tjh.dev
commits
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When I converted dell-wmi to the new bus infrastructure, I left the
call to dell_wmi_check_descriptor_buffer() in dell_wmi_init(). This
could cause two problems:
- An error message when loading the driver on a system without
dell-wmi. We'd try to read the event descriptor even if the WMI
GUID wasn't there.
- A possible race if dell-wmi was loaded manually before wmi was
fully initialized.
Fix it by moving the call to the probe function where it belongs.
Fixes: bff589be59c5 ("platform/x86: dell-wmi: Convert to the WMI bus infrastructure")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The latest change of compat_sys_sigpending in commit 8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abced ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a build error caused by not including <linux/bug.h>.
The following compilation errors are caused by the missing header:
arch/mips/ralink/mt7620.c: In function ‘mt7620_get_cpu_pll_rate’:
arch/mips/ralink/mt7620.c:431:2: error: implicit declaration of function ‘WARN_ON’ [-Werror=implicit-function-declaration]
WARN_ON(div >= ARRAY_SIZE(mt7620_clk_divider));
^
arch/mips/ralink/mt7620.c: In function ‘mt7620_get_sys_rate’:
arch/mips/ralink/mt7620.c:500:2: error: implicit declaration of function ‘WARN’ [-Werror=implicit-function-declaration]
if (WARN(!div, "invalid divider for OCP ratio %u", ocp_ratio))
^
arch/mips/ralink/mt7620.c: In function ‘mt7620_dram_init’:
arch/mips/ralink/mt7620.c:619:3: error: implicit declaration of function ‘BUG’ [-Werror=implicit-function-declaration]
BUG();
^
cc1: some warnings being treated as errors
scripts/Makefile.build:302: recipe for target 'arch/mips/ralink/mt7620.o' failed
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16781/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d66
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
The order of resource deallocations is messed up in acpi_wmi_init().
It should be vice versa.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
Previously, <linux/module.h> was included before ralink_regs.h in all
ralink files - leading to <linux/io.h> being implicitly included.
After commit 26dd3e4ff9ac ("MIPS: Audit and remove any unnecessary
uses of module.h") removed the inclusion of module.h from multiple
places, some ralink platforms failed to build with the following error:
In file included from arch/mips/ralink/mt7620.c:17:0:
./arch/mips/include/asm/mach-ralink/ralink_regs.h: In function ‘rt_sysc_w32’:
./arch/mips/include/asm/mach-ralink/ralink_regs.h:38:2: error: implicit declaration of function ‘__raw_writel’ [-Werror=implicit-function-declaration]
__raw_writel(val, rt_sysc_membase + reg);
^
./arch/mips/include/asm/mach-ralink/ralink_regs.h: In function ‘rt_sysc_r32’:
./arch/mips/include/asm/mach-ralink/ralink_regs.h:43:2: error: implicit declaration of function ‘__raw_readl’ [-Werror=implicit-function-declaration]
return __raw_readl(rt_sysc_membase + reg);
Fix this by including <linux/io.h>.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Fixes: 26dd3e4ff9ac ("MIPS: Audit and remove any unnecessary uses of module.h")
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> #4.11+
Patchwork: https://patchwork.linux-mips.org/patch/16780/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The new driver fails to build without INPUT_POLLDEV
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_exit':
peaq-wmi.c:(.exit.text+0x1c): undefined reference to `input_unregister_polled_device'
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_init':
peaq-wmi.c:(.init.text+0x23): undefined reference to `input_allocate_polled_device'
peaq-wmi.c:(.init.text+0x18e): undefined reference to `input_register_polled_device'
For some reason, all other drivers that need this use 'select'
here rather than 'depends on', so I'm doing the same.
Fixes: 13bb0fd5519d ("platform/x86: peaq-wmi: Add new peaq-wmi driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull GPIO fixes from Linus Walleij:
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical irqdomain
symbol properly - this happens to be done in the pin control
framework but whatever, it had dependencies to GPIO so we need to
apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray, also add the
right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
* tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: fix unbalanced chained_irq_enter/exit
gpiolib: skip unwanted events, don't convert them to opposite edge
gpio: exar: Use correct property prefix and document bindings
gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake source
gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHY
pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
gpio: lp87565: Set proper output level and direction for direction_output
MAINTAINERS: Add entry for Whiskey Cove PMIC GPIO driver
The code looks in imx_enum_frame_size() looks like this:
2066 int index = fse->index;
2067 struct imx_device *dev = to_imx_sensor(sd);
2068
2069 mutex_lock(&dev->input_lock);
2070 if (index >= dev->entries_curr_table) {
2071 mutex_unlock(&dev->input_lock);
2072 return -EINVAL;
2073 }
2074
2075 fse->min_width = dev->curr_res_table[index].width;
"fse->index" is a u32 that comes from the user. We want negative values
of "index" to be -EINVAL so we don't read before the start of the
dev->curr_res_table[] array. I've made "entries_curr_table" unsigned
long to fix this. I thought about making it unsigned int, but because
of struct alignment, it doesn't use more memory either way.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
When more than one GPIO IRQs are triggered simultaneously,
tegra_gpio_irq_handler() called chained_irq_exit() multiple
times for one chained_irq_enter().
Fixes: 3c92db9ac0ca3eee8e46e2424b6c074e2e394ad9
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
[Also changed the variable to a bool]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The problem is this code from ap1302_enum_frame_size():
738 int index = fse->index;
739
740 mutex_lock(&dev->input_lock);
741 context = ap1302_get_context(sd);
742 if (index >= dev->cntx_res[context].res_num) {
743 mutex_unlock(&dev->input_lock);
744 return -EINVAL;
745 }
746
747 res_table = dev->cntx_res[context].res_table;
748 fse->min_width = res_table[index].width;
"fse->index" is a u32 that come from the user. We want negative values
of "index" to be treated as -EINVAL but they're not so we can read from
before the start of the res_table[] array.
I've fixed this by making "res_num" a u32. I made "cur_res" a u32 as
well, just for consistency.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull documentation format standardization from Jonathan Corbet:
"This series converts a number of top-level documents to the RST format
without incorporating them into the Sphinx tree. The hope is to bring
some uniformity to kernel documentation and, perhaps more importantly,
have our existing docs serve as an example of the desired formatting
for those that will be added later.
Mauro has gone through and fixed up a lot of top-level documentation
files to make them conform to the RST format, but without moving or
renaming them in any way. This will help when we incorporate the ones
we want to keep into the Sphinx doctree, but the real purpose is to
bring a bit of uniformity to our documentation and let the top-level
docs serve as examples for those writing new ones"
* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
docs: kprobes.txt: Fix whitespacing
tee.txt: standardize document format
cgroup-v2.txt: standardize document format
dell_rbu.txt: standardize document format
zorro.txt: standardize document format
xz.txt: standardize document format
xillybus.txt: standardize document format
vfio.txt: standardize document format
vfio-mediated-device.txt: standardize document format
unaligned-memory-access.txt: standardize document format
this_cpu_ops.txt: standardize document format
svga.txt: standardize document format
static-keys.txt: standardize document format
smsc_ece1099.txt: standardize document format
SM501.txt: standardize document format
siphash.txt: standardize document format
sgi-ioc4.txt: standardize document format
SAK.txt: standardize document format
rpmsg.txt: standardize document format
robust-futexes.txt: standardize document format
...
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
Currently a bug in the sci_clk_get implementation causes it to always
return a clock belonging to the last device in the static list of clock
data. This is due to a bug in the init code that causes the array
used by sci_clk_get to only be populated with the clocks for the last
device, as each device overwrites the entire array with its own clocks.
Fix this by calculating the actual number of clocks for the SoC, and
allocating the whole array in one go. Also, we don't need the handle
to the init data array anymore after doing this, instead we can
just compare the dev_id / clk_id against the registered clocks and
use binary search for speed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Fixes: b745c0794e2f ("clk: keystone: Add sci-clk driver support")
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Franklin Cooper <fcooper@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The previous fix for filtering out of unwatched events was not entirely
correct. Instead of skipping the events we don't want, they are now
interpreted as events with opposing edge.
In order to fix it: always read the GPIO line value on interrupt and
only emit the event if it corresponds with the event type we requested.
Cc: stable@vger.kernel.org
Fixes: ad537b822577 ("gpiolib: fix filtering out unwanted events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The problem here is this code from atomisp_enum_input():
581 int index = input->index;
582
583 if (index >= isp->input_cnt)
584 return -EINVAL;
585
586 if (!isp->inputs[index].camera)
587 return -EINVAL;
"input->index" is a u32 which comes from the ioctl. We want negative
values of "index" to be counted as -EINVAL but they aren't. I've fixed
this by changing the type of "isp->input_cnt" to unsigned int.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
The notes at the end of this file start with a blank space,
instead of a blank line, violating ReST format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Pull x86 fix from Thomas Gleixner:
"The recent irq core changes unearthed API abuse in the HPET code,
which manifested itself in a suspend/resume regression.
The fix replaces the cruft with the proper function calls and cures
the regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Cure interface abuse in the resume path
KVM/ARM Fixes for v4.13-rc4
- Yet another race with VM destruction plugged
- A set of small vgic fixes
Pull one Allwinner clock fix from Chen-Yu Tsai:
One critical clock fix for sun5i (A10s/A13/R8) which enables propagation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
* tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a2f ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
Avoid the READ_ONCE in commit 4a072c71f49b ("random: silence compiler
warnings and fix race") if we can leave the function after
arch_get_random_XXX().
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Each text file under Documentation follows a different format. Some
doesn't even have titles!
Change its representation to follow the adopted standard,
using ReST markups for it to be parseable by Sphinx:
- adjust identation of titles;
- mark ascii artwork as a literal block;
- adjust references.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull timer fix from Thomas Gleixner:
"A single fix for a multiplication overflow in the timer code on 32bit
systems"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix overflow in get_next_timer_interrupt
The HPET resume path abuses irq_domain_[de]activate_irq() to restore the
MSI message in the HPET chip for the boot CPU on resume and it relies on an
implementation detail of the interrupt core code, which magically makes the
HPET unmask call invoked via a irq_disable/enable pair. This worked as long
as the irq code did unconditionally invoke the unmask() callback. With the
recent changes which keep track of the masked state to avoid expensive
hardware access, this does not longer work. As a consequence the HPET timer
interrupts are not unmasked which breaks resume as the boot CPU waits
forever that a timer interrupt arrives.
Make the restore of the MSI message explicit and invoke the unmask()
function directly. While at it get rid of the pointless affinity setting as
nothing can change the affinity of the interrupt and the vector across
suspend/resume. The restore of the MSI message reestablishes the previous
affinity setting which is the correct one.
Fixes: bf22ff45bed6 ("genirq: Avoid unnecessary low level irq function calls")
Reported-and-tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Martin Peres <martin.peres@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: jeffy.chen@rock-chips.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707312158590.2287@nanos
------------[ cut here ]------------
WARNING: CPU: 5 PID: 2288 at arch/x86/kvm/vmx.c:11124 nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
CPU: 5 PID: 2288 Comm: qemu-system-x86 Not tainted 4.13.0-rc2+ #7
RIP: 0010:nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
Call Trace:
vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
? vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x5dd/0x1be0 [kvm]
? vmx_vcpu_load+0x1be/0x220 [kvm_intel]
? kvm_arch_vcpu_load+0x62/0x230 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x8f/0x750
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL64_slow_path+0x25/0x25
This can be reproduced by booting L1 guest w/ 'noapic' grub parameter, which
means that tells the kernel to not make use of any IOAPICs that may be present
in the system.
Actually external_intr variable in nested_vmx_vmexit() is the req_int_win
variable passed from vcpu_enter_guest() which means that the L0's userspace
requests an irq window. I observed the scenario (!kvm_cpu_has_interrupt(vcpu) &&
L0's userspace reqeusts an irq window) is true, so there is no interrupt which
L1 requires to inject to L2, we should not attempt to emualte "Acknowledge
interrupt on exit" for the irq window requirement in this scenario.
This patch fixes it by not attempt to emulate "Acknowledge interrupt on exit"
if there is no L1 requirement to inject an interrupt to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Added code comment to make it obvious that the behavior is not correct.
We should do a userspace exit with open interrupt window instead of the
nested VM exit. This patch still improves the behavior, so it was
accepted as a (temporary) workaround.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is a small chance that the compiler could generate separate loads
for the dist->propbaser which could be modified from another CPU. As we
want to make sure we atomically update the entire value, and don't race
with other updates, guarantee that the cmpxchg operation compares
against the original value.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull one Meson clock fix from Neil Armstrong
* tag 'meson-clk-fixes-for-4.13-rc4-v2' of git://github.com/baylibre/clk-meson:
clk: meson: mpll: fix mpll0 fractional part ignored
The current CPU clock is missing the option to change the rate of its
parents, leading to improper rates calculated by cpufreq, and eventually
crashes.
Cc: <stable@vger.kernel.org>
Fixes: 5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the function gpio_set_wake_irq(), port->irq_high is only checked for
zero. As platform_get_irq() returns a value less then zero if no interrupt
was found, any gpio >= 16 was handled like an irq_high interrupt was
available. On iMX27 for example no high interrupt is available. This lead
to the problem that only some gpios (the lower 16) were useable as wake
sources.
Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68fd7 ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull more __copy_.._user elimination from Al Viro.
* 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
drm_dp_aux_dev: switch to read_iter/write_iter
The isofs patch needs a small fix to handle a signed/unsigned comparison that
the compiler didn't flag - thanks to Dan for catching it.
It should be noted, however, the session number handing appears to be incorrect
between where it is parsed and where it is used.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unfortunately, on some models of some architectures getting a fully
seeded CRNG is extremely difficult, and so this can result in dmesg
getting spammed for a surprisingly long time. This is really bad from
a security perspective, and so architecture maintainers really need to
do what they can to get the CRNG seeded sooner after the system is
booted. However, users can't do anything actionble to address this,
and spamming the kernel messages log will only just annoy people.
For developers who want to work on improving this situation,
CONFIG_WARN_UNSEEDED_RANDOM has been renamed to
CONFIG_WARN_ALL_UNSEEDED_RANDOM. By default the kernel will always
print the first use of unseeded randomness. This way, hopefully the
security obsessed will be happy that there is _some_ indication when
the kernel boots there may be a potential issue with that architecture
or subarchitecture. To see all uses of unseeded randomness,
developers can enable CONFIG_WARN_ALL_UNSEEDED_RANDOM.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Each text file under Documentation follows a different
format. Some doesn't even have titles!
Change its representation to follow the adopted standard,
using ReST markups for it to be parseable by Sphinx:
- Comment the internal index;
- Use :Date: and :Author: for authorship;
- Mark titles;
- Mark literal blocks;
- Adjust witespaces;
- Mark notes;
- Use table notation for the existing tables.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
For e.g. HZ=100, timer being 430 jiffies in the future, and 32 bit
unsigned int, there is an overflow on unsigned int right-hand side
of the expression which results with wrong values being returned.
Type cast the multiplier to 64bit to avoid that issue.
Fixes: 46c8f0b077a8 ("timers: Fix get_next_timer_interrupt() computation")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: khilman@baylibre.com
Cc: akpm@linux-foundation.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/a7900f04-2a21-c9fd-67be-ab334d459ee5@nokia.com
The host physical addresses of L1's Virtual APIC Page and Posted
Interrupt descriptor are loaded into the VMCS02. The CPU may write
to these pages via their host physical address while L2 is running,
bypassing address-translation-based dirty tracking (e.g. EPT write
protection). Mark them dirty on every exit from L2 to prevent them
from getting out of sync with dirty tracking.
Also mark the virtual APIC page and the posted interrupt descriptor
dirty when KVM is virtualizing posted interrupt processing.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Cc: stable@vger.kernel.org
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal = 24000000.
Fixes: 9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f01 ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
When I converted dell-wmi to the new bus infrastructure, I left the
call to dell_wmi_check_descriptor_buffer() in dell_wmi_init(). This
could cause two problems:
- An error message when loading the driver on a system without
dell-wmi. We'd try to read the event descriptor even if the WMI
GUID wasn't there.
- A possible race if dell-wmi was loaded manually before wmi was
fully initialized.
Fix it by moving the call to the probe function where it belongs.
Fixes: bff589be59c5 ("platform/x86: dell-wmi: Convert to the WMI bus infrastructure")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The latest change of compat_sys_sigpending in commit 8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abced ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a build error caused by not including <linux/bug.h>.
The following compilation errors are caused by the missing header:
arch/mips/ralink/mt7620.c: In function ‘mt7620_get_cpu_pll_rate’:
arch/mips/ralink/mt7620.c:431:2: error: implicit declaration of function ‘WARN_ON’ [-Werror=implicit-function-declaration]
WARN_ON(div >= ARRAY_SIZE(mt7620_clk_divider));
^
arch/mips/ralink/mt7620.c: In function ‘mt7620_get_sys_rate’:
arch/mips/ralink/mt7620.c:500:2: error: implicit declaration of function ‘WARN’ [-Werror=implicit-function-declaration]
if (WARN(!div, "invalid divider for OCP ratio %u", ocp_ratio))
^
arch/mips/ralink/mt7620.c: In function ‘mt7620_dram_init’:
arch/mips/ralink/mt7620.c:619:3: error: implicit declaration of function ‘BUG’ [-Werror=implicit-function-declaration]
BUG();
^
cc1: some warnings being treated as errors
scripts/Makefile.build:302: recipe for target 'arch/mips/ralink/mt7620.o' failed
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16781/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d66
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
Previously, <linux/module.h> was included before ralink_regs.h in all
ralink files - leading to <linux/io.h> being implicitly included.
After commit 26dd3e4ff9ac ("MIPS: Audit and remove any unnecessary
uses of module.h") removed the inclusion of module.h from multiple
places, some ralink platforms failed to build with the following error:
In file included from arch/mips/ralink/mt7620.c:17:0:
./arch/mips/include/asm/mach-ralink/ralink_regs.h: In function ‘rt_sysc_w32’:
./arch/mips/include/asm/mach-ralink/ralink_regs.h:38:2: error: implicit declaration of function ‘__raw_writel’ [-Werror=implicit-function-declaration]
__raw_writel(val, rt_sysc_membase + reg);
^
./arch/mips/include/asm/mach-ralink/ralink_regs.h: In function ‘rt_sysc_r32’:
./arch/mips/include/asm/mach-ralink/ralink_regs.h:43:2: error: implicit declaration of function ‘__raw_readl’ [-Werror=implicit-function-declaration]
return __raw_readl(rt_sysc_membase + reg);
Fix this by including <linux/io.h>.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Fixes: 26dd3e4ff9ac ("MIPS: Audit and remove any unnecessary uses of module.h")
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> #4.11+
Patchwork: https://patchwork.linux-mips.org/patch/16780/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The new driver fails to build without INPUT_POLLDEV
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_exit':
peaq-wmi.c:(.exit.text+0x1c): undefined reference to `input_unregister_polled_device'
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_init':
peaq-wmi.c:(.init.text+0x23): undefined reference to `input_allocate_polled_device'
peaq-wmi.c:(.init.text+0x18e): undefined reference to `input_register_polled_device'
For some reason, all other drivers that need this use 'select'
here rather than 'depends on', so I'm doing the same.
Fixes: 13bb0fd5519d ("platform/x86: peaq-wmi: Add new peaq-wmi driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull GPIO fixes from Linus Walleij:
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical irqdomain
symbol properly - this happens to be done in the pin control
framework but whatever, it had dependencies to GPIO so we need to
apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray, also add the
right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
* tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: fix unbalanced chained_irq_enter/exit
gpiolib: skip unwanted events, don't convert them to opposite edge
gpio: exar: Use correct property prefix and document bindings
gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake source
gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHY
pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
gpio: lp87565: Set proper output level and direction for direction_output
MAINTAINERS: Add entry for Whiskey Cove PMIC GPIO driver
The code looks in imx_enum_frame_size() looks like this:
2066 int index = fse->index;
2067 struct imx_device *dev = to_imx_sensor(sd);
2068
2069 mutex_lock(&dev->input_lock);
2070 if (index >= dev->entries_curr_table) {
2071 mutex_unlock(&dev->input_lock);
2072 return -EINVAL;
2073 }
2074
2075 fse->min_width = dev->curr_res_table[index].width;
"fse->index" is a u32 that comes from the user. We want negative values
of "index" to be -EINVAL so we don't read before the start of the
dev->curr_res_table[] array. I've made "entries_curr_table" unsigned
long to fix this. I thought about making it unsigned int, but because
of struct alignment, it doesn't use more memory either way.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
When more than one GPIO IRQs are triggered simultaneously,
tegra_gpio_irq_handler() called chained_irq_exit() multiple
times for one chained_irq_enter().
Fixes: 3c92db9ac0ca3eee8e46e2424b6c074e2e394ad9
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
[Also changed the variable to a bool]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The problem is this code from ap1302_enum_frame_size():
738 int index = fse->index;
739
740 mutex_lock(&dev->input_lock);
741 context = ap1302_get_context(sd);
742 if (index >= dev->cntx_res[context].res_num) {
743 mutex_unlock(&dev->input_lock);
744 return -EINVAL;
745 }
746
747 res_table = dev->cntx_res[context].res_table;
748 fse->min_width = res_table[index].width;
"fse->index" is a u32 that come from the user. We want negative values
of "index" to be treated as -EINVAL but they're not so we can read from
before the start of the res_table[] array.
I've fixed this by making "res_num" a u32. I made "cur_res" a u32 as
well, just for consistency.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull documentation format standardization from Jonathan Corbet:
"This series converts a number of top-level documents to the RST format
without incorporating them into the Sphinx tree. The hope is to bring
some uniformity to kernel documentation and, perhaps more importantly,
have our existing docs serve as an example of the desired formatting
for those that will be added later.
Mauro has gone through and fixed up a lot of top-level documentation
files to make them conform to the RST format, but without moving or
renaming them in any way. This will help when we incorporate the ones
we want to keep into the Sphinx doctree, but the real purpose is to
bring a bit of uniformity to our documentation and let the top-level
docs serve as examples for those writing new ones"
* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
docs: kprobes.txt: Fix whitespacing
tee.txt: standardize document format
cgroup-v2.txt: standardize document format
dell_rbu.txt: standardize document format
zorro.txt: standardize document format
xz.txt: standardize document format
xillybus.txt: standardize document format
vfio.txt: standardize document format
vfio-mediated-device.txt: standardize document format
unaligned-memory-access.txt: standardize document format
this_cpu_ops.txt: standardize document format
svga.txt: standardize document format
static-keys.txt: standardize document format
smsc_ece1099.txt: standardize document format
SM501.txt: standardize document format
siphash.txt: standardize document format
sgi-ioc4.txt: standardize document format
SAK.txt: standardize document format
rpmsg.txt: standardize document format
robust-futexes.txt: standardize document format
...
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
Currently a bug in the sci_clk_get implementation causes it to always
return a clock belonging to the last device in the static list of clock
data. This is due to a bug in the init code that causes the array
used by sci_clk_get to only be populated with the clocks for the last
device, as each device overwrites the entire array with its own clocks.
Fix this by calculating the actual number of clocks for the SoC, and
allocating the whole array in one go. Also, we don't need the handle
to the init data array anymore after doing this, instead we can
just compare the dev_id / clk_id against the registered clocks and
use binary search for speed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Fixes: b745c0794e2f ("clk: keystone: Add sci-clk driver support")
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Franklin Cooper <fcooper@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The previous fix for filtering out of unwatched events was not entirely
correct. Instead of skipping the events we don't want, they are now
interpreted as events with opposing edge.
In order to fix it: always read the GPIO line value on interrupt and
only emit the event if it corresponds with the event type we requested.
Cc: stable@vger.kernel.org
Fixes: ad537b822577 ("gpiolib: fix filtering out unwanted events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The problem here is this code from atomisp_enum_input():
581 int index = input->index;
582
583 if (index >= isp->input_cnt)
584 return -EINVAL;
585
586 if (!isp->inputs[index].camera)
587 return -EINVAL;
"input->index" is a u32 which comes from the ioctl. We want negative
values of "index" to be counted as -EINVAL but they aren't. I've fixed
this by changing the type of "isp->input_cnt" to unsigned int.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
Pull x86 fix from Thomas Gleixner:
"The recent irq core changes unearthed API abuse in the HPET code,
which manifested itself in a suspend/resume regression.
The fix replaces the cruft with the proper function calls and cures
the regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Cure interface abuse in the resume path
Pull one Allwinner clock fix from Chen-Yu Tsai:
One critical clock fix for sun5i (A10s/A13/R8) which enables propagation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
* tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a2f ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
Each text file under Documentation follows a different format. Some
doesn't even have titles!
Change its representation to follow the adopted standard,
using ReST markups for it to be parseable by Sphinx:
- adjust identation of titles;
- mark ascii artwork as a literal block;
- adjust references.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The HPET resume path abuses irq_domain_[de]activate_irq() to restore the
MSI message in the HPET chip for the boot CPU on resume and it relies on an
implementation detail of the interrupt core code, which magically makes the
HPET unmask call invoked via a irq_disable/enable pair. This worked as long
as the irq code did unconditionally invoke the unmask() callback. With the
recent changes which keep track of the masked state to avoid expensive
hardware access, this does not longer work. As a consequence the HPET timer
interrupts are not unmasked which breaks resume as the boot CPU waits
forever that a timer interrupt arrives.
Make the restore of the MSI message explicit and invoke the unmask()
function directly. While at it get rid of the pointless affinity setting as
nothing can change the affinity of the interrupt and the vector across
suspend/resume. The restore of the MSI message reestablishes the previous
affinity setting which is the correct one.
Fixes: bf22ff45bed6 ("genirq: Avoid unnecessary low level irq function calls")
Reported-and-tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Martin Peres <martin.peres@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: jeffy.chen@rock-chips.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707312158590.2287@nanos
------------[ cut here ]------------
WARNING: CPU: 5 PID: 2288 at arch/x86/kvm/vmx.c:11124 nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
CPU: 5 PID: 2288 Comm: qemu-system-x86 Not tainted 4.13.0-rc2+ #7
RIP: 0010:nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
Call Trace:
vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
? vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x5dd/0x1be0 [kvm]
? vmx_vcpu_load+0x1be/0x220 [kvm_intel]
? kvm_arch_vcpu_load+0x62/0x230 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x8f/0x750
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL64_slow_path+0x25/0x25
This can be reproduced by booting L1 guest w/ 'noapic' grub parameter, which
means that tells the kernel to not make use of any IOAPICs that may be present
in the system.
Actually external_intr variable in nested_vmx_vmexit() is the req_int_win
variable passed from vcpu_enter_guest() which means that the L0's userspace
requests an irq window. I observed the scenario (!kvm_cpu_has_interrupt(vcpu) &&
L0's userspace reqeusts an irq window) is true, so there is no interrupt which
L1 requires to inject to L2, we should not attempt to emualte "Acknowledge
interrupt on exit" for the irq window requirement in this scenario.
This patch fixes it by not attempt to emulate "Acknowledge interrupt on exit"
if there is no L1 requirement to inject an interrupt to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Added code comment to make it obvious that the behavior is not correct.
We should do a userspace exit with open interrupt window instead of the
nested VM exit. This patch still improves the behavior, so it was
accepted as a (temporary) workaround.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is a small chance that the compiler could generate separate loads
for the dist->propbaser which could be modified from another CPU. As we
want to make sure we atomically update the entire value, and don't race
with other updates, guarantee that the cmpxchg operation compares
against the original value.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current CPU clock is missing the option to change the rate of its
parents, leading to improper rates calculated by cpufreq, and eventually
crashes.
Cc: <stable@vger.kernel.org>
Fixes: 5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the function gpio_set_wake_irq(), port->irq_high is only checked for
zero. As platform_get_irq() returns a value less then zero if no interrupt
was found, any gpio >= 16 was handled like an irq_high interrupt was
available. On iMX27 for example no high interrupt is available. This lead
to the problem that only some gpios (the lower 16) were useable as wake
sources.
Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68fd7 ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The isofs patch needs a small fix to handle a signed/unsigned comparison that
the compiler didn't flag - thanks to Dan for catching it.
It should be noted, however, the session number handing appears to be incorrect
between where it is parsed and where it is used.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unfortunately, on some models of some architectures getting a fully
seeded CRNG is extremely difficult, and so this can result in dmesg
getting spammed for a surprisingly long time. This is really bad from
a security perspective, and so architecture maintainers really need to
do what they can to get the CRNG seeded sooner after the system is
booted. However, users can't do anything actionble to address this,
and spamming the kernel messages log will only just annoy people.
For developers who want to work on improving this situation,
CONFIG_WARN_UNSEEDED_RANDOM has been renamed to
CONFIG_WARN_ALL_UNSEEDED_RANDOM. By default the kernel will always
print the first use of unseeded randomness. This way, hopefully the
security obsessed will be happy that there is _some_ indication when
the kernel boots there may be a potential issue with that architecture
or subarchitecture. To see all uses of unseeded randomness,
developers can enable CONFIG_WARN_ALL_UNSEEDED_RANDOM.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Each text file under Documentation follows a different
format. Some doesn't even have titles!
Change its representation to follow the adopted standard,
using ReST markups for it to be parseable by Sphinx:
- Comment the internal index;
- Use :Date: and :Author: for authorship;
- Mark titles;
- Mark literal blocks;
- Adjust witespaces;
- Mark notes;
- Use table notation for the existing tables.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
For e.g. HZ=100, timer being 430 jiffies in the future, and 32 bit
unsigned int, there is an overflow on unsigned int right-hand side
of the expression which results with wrong values being returned.
Type cast the multiplier to 64bit to avoid that issue.
Fixes: 46c8f0b077a8 ("timers: Fix get_next_timer_interrupt() computation")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: khilman@baylibre.com
Cc: akpm@linux-foundation.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/a7900f04-2a21-c9fd-67be-ab334d459ee5@nokia.com
The host physical addresses of L1's Virtual APIC Page and Posted
Interrupt descriptor are loaded into the VMCS02. The CPU may write
to these pages via their host physical address while L2 is running,
bypassing address-translation-based dirty tracking (e.g. EPT write
protection). Mark them dirty on every exit from L2 to prevent them
from getting out of sync with dirty tracking.
Also mark the virtual APIC page and the posted interrupt descriptor
dirty when KVM is virtualizing posted interrupt processing.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Cc: stable@vger.kernel.org
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal = 24000000.
Fixes: 9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f01 ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>