Merge tag 'omap-for-v4.17/dt-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "Second set of dts changes for omap variants for v4.17" from Tony Lindgren:

This series of patches configures few new drivers and adds
omap5 specific nodes:

- Enable USB OTG mode for xhci on am437x

- A series of changes to configure aux control module instance
on omap5 mostly to get the audio clocks configured

- A series of changes to update droid4 for MDM6600 modem USB PHY
and UART1 pinctrl

* tag 'omap-for-v4.17/dt-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Configure uart1 pins
ARM: dts: omap4-droid4: Configure MDM6600 USB PHY
ARM: dts: omap4-droid4: Fix USB PHY port naming
ARM: dts: omap5-board-common: Add phandle for mclk clock for twl6040
ARM: dts: omap5: add fref_xtal_ck support
ARM: dts: omap5: add support for control module wkup pad config
dt-bindings: omap5: ctrl: Support for control module wkup pad config
ARM: dts: am43xx: Enable dual-role mode for USB1

Documentation/devicetree/bindings/arm/omap/ctrl.txt

···
 		"ti,omap4-scm-padconf-wkup"
 		"ti,omap5-scm-core"
 		"ti,omap5-scm-padconf-core"
+		"ti,omap5-scm-wkup-pad-conf"
 		"ti,dra7-scm-core"
 - reg:		Contains Control Module register address range
 		(base address and length)

arch/arm/boot/dts/am437x-gp-evm.dts

···
 };
 
 &usb1 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 };
 

arch/arm/boot/dts/am437x-sk-evm.dts

···
 };
 
 &usb1 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb1_pins>;

arch/arm/boot/dts/am43x-epos-evm.dts

···
 };
 
 &usb1 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 };
 

arch/arm/boot/dts/omap4-droid4-xt894.dts

···
 		regulator-always-on;
 	};
 
-	/* HS USB Host PHY on PORT 1 */
-	hsusb1_phy: hsusb1_phy {
+	/* FS USB Host PHY on port 1 for mdm6600 */
+	fsusb1_phy: usb-phy@1 {
+		compatible = "motorola,mapphone-mdm6600";
+		pinctrl-0 = <&usb_mdm6600_pins>;
+		pinctrl-names = "default";
+		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
+		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
+		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
+		/* mode: gpio_148 gpio_149 */
+		motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
+				      <&gpio5 21 GPIO_ACTIVE_HIGH>;
+		/* cmd: gpio_103 gpio_104 gpio_142 */
+		motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
+				     <&gpio4 8 GPIO_ACTIVE_HIGH>,
+				     <&gpio5 14 GPIO_ACTIVE_HIGH>;
+		/* status: gpio_52 gpio_53 gpio_55 */
+		motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
+					<&gpio2 21 GPIO_ACTIVE_HIGH>,
+					<&gpio2 23 GPIO_ACTIVE_HIGH>;
+		#phy-cells = <0>;
+	};
+
+	/* HS USB host TLL nop-phy on port 2 for w3glte */
+	hsusb2_phy: usb-phy@2 {
 		compatible = "usb-nop-xceiv";
 		#phy-cells = <0>;
 	};
···
 		>;
 	};
 
+	usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
+		pinctrl-single,pins = <
+		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
+		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
+
+		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
+		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
+
+		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
+		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
+		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
+		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
+
+		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
+		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
+
+		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
+		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
+
+		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
+		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
+
+		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
+		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
+		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
+		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
 	usb_ulpi_pins: pinmux_usb_ulpi_pins {
 		pinctrl-single,pins = <
 		OMAP4_IOPAD(0x196, MUX_MODE7)
···
 		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
+		>;
+	};
+
+	/*
+	 * Note that the v3.0.8 stock userspace dynamically remuxes uart1
+	 * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
+	 * when not used. If needed, we can add rts pin remux later based
+	 * on power measurements.
+	 */
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+		/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
+		OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
+		OMAP4_IOPAD(0x13e, MUX_MODE1)
+
+		/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
+		OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
+
+		/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
+		OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
 		>;
 	};
 
···
 	};
 };
 
+/*
+ * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
+ * uart1 wakeirq.
+ */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0xfc>;
+};
+
 &uart3 {
 	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 			       &omap4_pmx_core 0x17c>;
···
 	};
 };
 
+&usbhsohci {
+	phys = <&fsusb1_phy>;
+	phy-names = "usb";
+};
+
 &usbhsehci {
-	phys = <&hsusb1_phy>;
+	phys = <&hsusb2_phy>;
 };
 
 &usbhshost {

arch/arm/boot/dts/omap5-board-common.dtsi

···
 		v2v1-supply = <&smps9_reg>;
 		enable-active-high;
 
-		clocks = <&clk32kgaudio>;
-		clock-names = "clk32k";
+		clocks = <&clk32kgaudio>, <&fref_xtal_ck>;
+		clock-names = "clk32k", "mclk";
 	};
 };
 

arch/arm/boot/dts/omap5.dtsi

···
 				pinctrl-single,register-width = <16>;
 				pinctrl-single,function-mask = <0x7fff>;
 			};
+
+			omap5_scm_wkup_pad_conf: omap5_scm_wkup_pad_conf@cda0 {
+				compatible = "ti,omap5-scm-wkup-pad-conf",
+					     "simple-bus";
+				reg = <0xcda0 0x60>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0xcda0 0x60>;
+
+				scm_wkup_pad_conf: scm_conf@0 {
+					compatible = "syscon", "simple-bus";
+					reg = <0x0 0x60>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x0 0x60>;
+
+					scm_wkup_pad_conf_clocks: clocks@0 {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+			};
 		};
 
 		ocmcram: ocmcram@40300000 {

arch/arm/boot/dts/omap54xx-clocks.dtsi

···
 		};
 	};
 };
+
+&scm_wkup_pad_conf_clocks {
+	fref_xtal_ck: fref_xtal_ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&sys_clkin>;
+		ti,bit-shift = <28>;
+		reg = <0x14>;
+	};
+};