tjh.dev
commits
Pull parisc fix from Helge Deller:
"This is a 2-line patch to save the CPU register which holds our task
thread info pointer before calling a firmware function and then to
restore it again afterwards.
This is necessary because on some 64bit machines the high-order 32bits
are being clobbered by the firmware call, and thus we failed to bring
up secondary CPUs (and instead crashed the kernel) in some situations
eg if we had more than 4GB RAM. This patch fixes a bug which has been
since ever in the parisc linux kernel and which prevented some people
to use a 64bit kernel"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM
Pull timer fix from Ingo Molnar:
"This tree contains a clockevents regression fix for certain ARM
subarchitectures"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Sanitize ticks to nsec conversion
Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel. The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.
In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.
Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.
So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
info pointer was located above the 4GB boundary.
Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull perf fixes from Ingo Molnar:
"The tree contains three fixes:
- Two tooling fixes
- Reversal of the new 'MMAP2' extended mmap record ABI, introduced in
this merge window. (Patches were proposed to fix it but it was all
a bit late and we felt it's safer to just delay the ABI one more
kernel release and do it right)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Disable PERF_RECORD_MMAP2 support
perf scripting perl: Fix build error on Fedora 12
perf probe: Fix to initialize fname always before use it
Marc Kleine-Budde pointed out, that commit 77cc982 "clocksource: use
clockevents_config_and_register() where possible" caused a regression
for some of the converted subarchs.
The reason is, that the clockevents core code converts the minimal
hardware tick delta to a nanosecond value for core internal
usage. This conversion is affected by integer math rounding loss, so
the backwards conversion to hardware ticks will likely result in a
value which is less than the configured hardware limitation. The
affected subarchs used their own workaround (SIGH!) which got lost in
the conversion.
The solution for the issue at hand is simple: adding evt->mult - 1 to
the shifted value before the integer divison in the core conversion
function takes care of it. But this only works for the case where for
the scaled math mult/shift pair "mult <= 1 << shift" is true. For the
case where "mult > 1 << shift" we can apply the rounding add only for
the minimum delta value to make sure that the backward conversion is
not less than the given hardware limit. For the upper bound we need to
omit the rounding add, because the backwards conversion is always
larger than the original latch value. That would violate the upper
bound of the hardware device.
Though looking closer at the details of that function reveals another
bogosity: The upper bounds check is broken as well. Checking for a
resulting "clc" value greater than KTIME_MAX after the conversion is
pointless. The conversion does:
u64 clc = (latch << evt->shift) / evt->mult;
So there is no sanity check for (latch << evt->shift) exceeding the
64bit boundary. The latch argument is "unsigned long", so on a 64bit
arch the handed in argument could easily lead to an unnoticed shift
overflow. With the above rounding fix applied the calculation before
the divison is:
u64 clc = (latch << evt->shift) + evt->mult - 1;
So we need to make sure, that neither the shift nor the rounding add
is overflowing the u64 boundary.
[ukl: move assignment to rnd after eventually changing mult, fix build
issue and correct comment with the right math]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: nicolas.ferre@atmel.com
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: john.stultz@linaro.org
Cc: kernel@pengutronix.de
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1380052223-24139-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull ACPI and power management fixes from
"These fix two bugs in the intel_pstate driver, a hibernate bug leading
to nasty resume failures sometimes and acpi-cpufreq initialization bug
that causes problems to happen during module unload when intel_pstate
is in use.
Specifics:
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing of
the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory when
the driver cannot be registered and then attempting to unregister
things that have never been registered on exit"
* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi-cpufreq: Fail initialization if driver cannot be registered
PM / hibernate: Move software_resume to late_initcall_sync
intel_pstate: Correct calculation of min pstate value
intel_pstate: Improve accuracy by not truncating until final result
Pull locking fix from Ingo Molnar:
"This tree fixes a boot crash in CONFIG_DEBUG_MUTEXES=y kernels, on
kernels built with GCC 3.x (there are still such distros)"
Side note: it's not just a fix for old gcc versions, it's also removing
an incredibly broken/subtle check that LLVM had issues with, and that
made no sense.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Avoid gcc version dependent __builtin_constant_p() usage
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
" * Fix build error on Fedora 12.
* Fix to initialize fname always before use it, bug introduced
during this merge window, from Masami Hiramatsu.
* Disable PERF_RECORD_MMAP2 support, from Stephane Eranian. "
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull s390 fixes from Martin Schwidefsky:
"Several last minute bug fixes.
Two of them are on the larger side for rc7, the dasd format patch for
older storage devices and the store-clock-fast patch where we have
been to optimistic with an optimization"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/time: correct use of store clock fast
s390/vmlogrdr: fix array access in vmlogrdr_open()
s390/compat,signal: fix return value of copy_siginfo_(to|from)_user32()
s390/dasd: check for availability of prefix command during format
s390/mm,kvm: fix software dirty bits vs. kvm for old machines
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
Commit 040a0a37 ("mutex: Add support for wound/wait style locks")
used "!__builtin_constant_p(p == NULL)" but gcc 3.x cannot
handle such expression correctly, leading to boot failure when
built with CONFIG_DEBUG_MUTEXES=y.
Fix it by explicitly passing a bool which tells whether p != NULL
or not.
[ PeterZ: This is a sad patch, but provided it actually generates
similar code I suppose its the best we can do bar whole
sale deprecating gcc-3. ]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: peterz@infradead.org
Cc: imirkin@alum.mit.edu
Cc: daniel.vetter@ffwll.ch
Cc: robdclark@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/201310171945.AGB17114.FSQVtHOJFOOFML@I-love.SAKURA.ne.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For now, we disable the extended MMAP record support (MMAP2).
We have identified cases where it would not report the correct mapping
information, clone(VM_CLONE) but with separate pids. We will revisit
the support once we find a solution for this case.
The patch changes the kernel to return EINVAL if attr->mmap2 is set. The
patch also modifies the perf tool to use regular PERF_RECORD_MMAP for
synthetic events and it also prevents the tool from requesting
attr->mmap2 mode because the kernel would reject it.
The support will be revisited once the kenrel interface is updated.
In V2, we reduce the patch to the strict minimum.
In V3, we avoid calling perf_event_open() with mmap2 set because we know
it will fail and require fallback retry.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131017173215.GA8820@quad
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull thermal management fixes from Zhang Rui:
"These includes several commits that are necessary to properly fix
regression for TMU test MUX address setting after reset, for exynos
thermal driver.
Specifics:
- fix a regression that the removal of setting a certain field at TMU
configuration setting results in immediately shutdown after reset
on Exynos4412 SoC.
- revert a patch which tries to link the thermal_zone device and its
hwmon node but breaks libsensors.
- fix a deadlock/lockdep warning issue in x86_pkg_temp thermal
driver, which can be reproduced on a buggy platform only.
- fix ti-soc-thermal driver to fall back on bandgap reading when
reading from PCB temperature sensor fails"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Revert "drivers: thermal: parent virtual hwmon with thermal zone"
drivers: thermal: allow ti-soc-thermal run without pcb zone
thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
thermal: exynos: Provide separate TMU data for Exynos4412
thermal: exynos: Remove check for thermal device pointer at exynos_report_trigger()
Thermal: x86_pkg_temp: change spin lock
The result of the store-clock-fast (STCKF) instruction is a bit fuzzy.
It can happen that the value stored on one CPU is smaller than the value
stored on another CPU, although the order of the stores is the other
way around. This can cause deltas of get_tod_clock() values to become
negative when they should not be.
We need to be more careful with store-clock-fast, this patch partially
reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time:
always use stckf instead of stck if available". The get_tod_clock()
function now uses the store-clock-extended (STCKE) instruction.
get_tod_clock_fast() can be used if the fuzziness of store-clock-fast
is acceptable e.g. for wait loops local to a CPU.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull vfs fixes (try two) from Al Viro:
"nfsd performance regression fix + seq_file lseek(2) fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: always update file->f_pos in seq_lseek()
nfsd regression since delayed fput()
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
software_resume is being called after deferred_probe_initcall in
drivers base. If the probing of the device that contains the resume
image is deferred, and the system has been instructed to wait for
it to show up, this wait will occur in software_resume. This causes
a deadlock.
Move software_resume into late_initcall_sync so that it happens
after all the other late_initcalls.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Pavel Machek <Pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the late fixes pull request for dmaengine while you fly back
from KS.
We have a new dmaengine ML hosted by vger so a patch for that along
with addition of Dave as driver mainatainer for ioat. Other fixes are
memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
by Sergei"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: edma: fix another memory leak
dma: edma: Fix memory leak
MAINTAINERS: add to ioatdma maintainer list
MAINTAINERS: add the new dmaengine mailing list
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull CIFS fixes from Steve French:
"Five small cifs fixes (includes fixes for: unmount hang, 2 security
related, symlink, large file writes)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ntstatus_to_dos_map[] is not terminated
cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
cifs: Fix inability to write files >2GB to SMB2/3 shares
cifs: Avoid umount hangs with smb2 when server is unresponsive
do not treat non-symlink reparse points as valid symlinks
Pull btrfs fix from Chris Mason:
"Sage hit a deadlock with ceph on btrfs, and Josef tracked it down to a
regression in our initial rc1 pull. When doing nocow writes we were
sometimes starting a transaction with locks held"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: release path before starting transaction in can_nocow_extent
Cast __u64 to u64 to silence this warning on older distros, such as
Fedora 12:
CC /tmp/build/perf/util/scripting-engines/trace-event-perl.o
cc1: warnings being treated as errors
util/scripting-engines/trace-event-perl.c: In function ‘perl_process_tracepoint’:
util/scripting-engines/trace-event-perl.c:285: error: format ‘%lu’ expects type ‘long unsigned int’, but argument 2 has type ‘__u64’
make[1]: *** [/tmp/build/perf/util/scripting-engines/trace-event-perl.o] Error 1
make: *** [install] Error 2
make: Leaving directory `/home/acme/git/linux/tools/perf'
[acme@fedora12 linux]$
Reported-by: Waiman Long <Waiman.Long@hp.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/n/tip-nlxofdqcdjfm0w9o6bgq4kqv@git.kernel.org
Link: http://lkml.kernel.org/r/1381265120-58532-1-git-send-email-Waiman.Long@hp.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix build error in asus_wmi.c when ASUS_WMI=y and ACPI_VIDEO=m
by preventing that combination.
drivers/built-in.o: In function `asus_wmi_probe':
asus-wmi.c:(.text+0x65ddb4): undefined reference to `acpi_video_unregister'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix check within vmlogrdr_open() if the minor address is not larger
than the number of array elements.
Found with "smatch":
drivers/s390/char/vmlogrdr.c:318 vmlogrdr_open() warn:
buffer overflow 'sys_ser' 3 <= 3
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41
As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:
char str1[32] = { 0 };
char str2[32] = { 0 };
int poffset = 10;
int count = 20;
/*open any seq file*/
int fd = open("/proc/modules", O_RDONLY);
pread(fd, str1, count, poffset);
printf("pread:%s\n", str1);
/*seek to where m->read_pos is*/
lseek(fd, poffset+count, SEEK_SET);
/*supposed to read from poffset+count, but this read from position 0*/
read(fd, str2, count);
printf("read:%s\n", str2);
out put:
pread:
ck_netbios_ns 12665
read:
nf_conntrack_netbios
/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000
So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In a recent commit:
commit f455578dd961087a5cf94730d9f6489bb1d355f0
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon Aug 12 14:14:53 2013 -0300
mtd: nand: pxa3xx: Remove hardcoded mtd name
There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.
Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.
While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The minimum pstate is supposed to be a percentage of the maximum P
state available. Calculate min using max pstate and not the
current max which may have been limited by the user
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 4b6271a6 fix a menory leak but one more existed in driver so fix that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull driver core fix from Greg KH:
"Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1"
* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
Functions that walk the ntstatus_to_dos_map[] array could
run off the end. For example, ntstatus_to_dos() loops
while ntstatus_to_dos_map[].ntstatus is not 0. Granted,
this is mostly theoretical, but could be used as a DOS attack
if the error code in the SMB header is bogus.
[Might consider adding to stable, as this patch is low risk - Steve]
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Pull ACPI and power management fixes from Rafael Wysocki:
- intel_pstate fix for misbehavior after system resume if sysfs
attributes are set in a specific way before the corresponding suspend
from Dirk Brandewie.
- A recent intel_pstate fix has no effect if unsigned long is 32-bit,
so fix it up to cover that case as well.
- The s3c64xx cpufreq driver was not updated when the index field of
struct cpufreq_frequency_table was replaced with driver_data, so
update it now. From Charles Keepax.
- The Kconfig help text for ACPI_BUTTON still refers to
/proc/acpi/event that has been dropped recently, so modify it to
remove that reference. From Krzysztof Mazur.
- A Lan Tianyu's change adds a missing mutex unlock to an error code
path in acpi_resume_power_resources().
- Some code related to ACPI power resources, whose very purpose is
questionable to put it lightly, turns out to cause problems to happen
during testing on real systems, so remove it completely (we may
revisit that in the future if there's a compelling enough reason).
From Rafael J Wysocki and Aaron Lu.
* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
cpufreq: s3c64xx: Rename index to driver_data
ACPI / power: Drop automaitc resume of power resource dependent devices
intel_pstate: Fix type mismatch warning
cpufreq / intel_pstate: Fix max_perf_pct on resume
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
We can't be holding tree locks while we try to start a transaction, we will
deadlock. Thanks,
Reported-by: Sage Weil <sage@inktank.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Fix perf probe --list to initialize fname local var always before
use it. This may cause a SEGV if there is a probe which is in
the function body but not in any inline function.
Problem introduced in:
commit e08cfd4bda76
Author: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Date: Mon Sep 30 18:21:44 2013 +0900
perf probe: Fix to find line information for probe list
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20131011122317.9662.29736.stgit@kbuild-fedora.novalocal
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b82715fdd4a5407f56853b24d387d484dd9c3b5b introduces
a 'device' subdirectory under /sys/class/hwmon/hwmonX/ directory,
for the thermal_zone hwmon devices. And this results in different
handling by libsensors.
The problem is reported and discussed in this thread
http://marc.info/?l=linux-pm&m=138229306109596&w=2
This patch reverts commit b82715fdd4a5407f56853b24d387d484dd9c3b5b.
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
x86_pkg_temp receives thermal notifications via a callback from a
therm_throt driver, where thermal interrupts are processed.
This callback is pkg_temp_thermal_platform_thermal_notify. Here to
avoid multiple interrupts from cores in a package, we disable the
source and also set a variable to avoid scheduling delayed work function.
This variable is protected via spin_lock_irqsave. On one buggy platform,
we still receiving interrupts even if the source is disabled. This
can cause deadlock/lockdep warning, when interrupt is generated while under
spinlock in work function.
Change spin_lock to spin_lock_irqsave and spin_unlock to
spin_unlock_irqrestore as the data it is trying to protect can also
be modified in a notification call called from interrupt handler.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The return value of copy_siginfo_(to|from)_user32() gets passed to
user space, however we do not convert a positive return value from
copy_(to|from)_user to -EFAULT.
Therefore these functions (and the calling system calls) my incorrectly
return a positive number (bytes not copied) instead of -EFAULT.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull ecryptfs fixes from Tyler Hicks:
"Two important fixes
- Fix long standing memory leak in the (rarely used) public key
support
- Fix large file corruption on 32 bit architectures"
* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: fix 32 bit corruption issue
ecryptfs: Fix memory leakage in keystore.c
I plan to stay with the Rockchip SoCs for the foreseable future
and hope to expand its support along the way.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Background: nfsd v[23] had throughput regression since delayed fput
went in; every read or write ends up doing fput() and we get a pair
of extra context switches out of that (plus quite a bit of work
in queue_work itselfi, apparently). Use of schedule_delayed_work()
gives it a chance to accumulate a bit before we do __fput() on all
of them. I'm not too happy about that solution, but... on at least
one real-world setup it reverts about 10% throughput loss we got from
switch to delayed fput.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull MTD fixes from Brian Norris:
- fix a small memory leak in some new ONFI code
- account for additional odd variations of Micron SPI flash
Acked by David Woodhouse.
* tag 'for-linus-20131008' of git://git.infradead.org/linux-mtd:
mtd: m25p80: Fix 4 byte addressing mode for Micron devices.
mtd: nand: fix memory leak in ONFI extended parameter page
This patch addresses Bug 60727
(https://bugzilla.kernel.org/show_bug.cgi?id=60727)
which was due to the truncation of intermediate values in the
calculations, which causes the code to consistently underestimate the
current cpu frequency, specifically 100% cpu utilization was truncated
down to the setpoint of 97%. This patch fixes the problem by keeping
the results of all intermediate calculations as fixed point numbers
rather scaling them back and forth between integers and fixed point.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60727
Signed-off-by: Brennan Shacklett <bpshacklett@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When it fails to allocate a slot, edesc should be free'd before return;
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds an explicit check + failure for XCOPY I/O to source +
destination devices with a non-matching block_size.
This limitiation is currently due to the fact that the scatterlist
memory allocated for the XCOPY READ operation is passed zero-copy
to the XCOPY WRITE operation.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
When inserting a wrong value to /sys/devices/system/memory/memoryX/state file,
following messages are shown. And device_hotplug_lock is never released.
================================================
[ BUG: lock held when returning to user space! ]
3.12.0-rc4-debug+ #3 Tainted: G W
------------------------------------------------
bash/6442 is leaving the kernel with locks still held!
1 lock held by bash/6442:
#0: (device_hotplug_lock){+.+.+.}, at: [<ffffffff8146cbb5>] lock_device_hotplug_sysfs+0x15/0x50
This issue was introdued by commit fa2be40 (drivers: base: use standard
device online/offline for state change).
This patch releases device_hotplug_lcok when store_mem_state returns EINVAL.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
CC: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows users to use LANMAN authentication on servers which support
unencapsulated authentication.
The patch fixes a regression where users using plaintext authentication
were no longer able to do so because of changed bought in by patch
3f618223dc0bdcbc8d510350e78ee2195ff93768
https://bugzilla.redhat.com/show_bug.cgi?id=1011621
Reported-by: Panos Kavalagios <Panagiotis.Kavalagios@eurodyn.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Pull x86 fixes from Ingo Molnar:
"Two fixlets:
- fix a (rare-config) build bug
- fix a next-gen SGI/UV hw/firmware enumeration bug"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Update UV3 hub revision ID
x86/microcode: Correct Kconfig dependencies
* acpi-fixes:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
ACPI / power: Drop automaitc resume of power resource dependent devices
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
When doing space balance and subvolume destroy at the same time, we met
the following oops:
kernel BUG at fs/btrfs/relocation.c:2247!
RIP: 0010: [<ffffffffa04cec16>] prepare_to_merge+0x154/0x1f0 [btrfs]
Call Trace:
[<ffffffffa04b5ab7>] relocate_block_group+0x466/0x4e6 [btrfs]
[<ffffffffa04b5c7a>] btrfs_relocate_block_group+0x143/0x275 [btrfs]
[<ffffffffa0495c56>] btrfs_relocate_chunk.isra.27+0x5c/0x5a2 [btrfs]
[<ffffffffa0459871>] ? btrfs_item_key_to_cpu+0x15/0x31 [btrfs]
[<ffffffffa048b46a>] ? btrfs_get_token_64+0x7e/0xcd [btrfs]
[<ffffffffa04a3467>] ? btrfs_tree_read_unlock_blocking+0xb2/0xb7 [btrfs]
[<ffffffffa049907d>] btrfs_balance+0x9c7/0xb6f [btrfs]
[<ffffffffa049ef84>] btrfs_ioctl_balance+0x234/0x2ac [btrfs]
[<ffffffffa04a1e8e>] btrfs_ioctl+0xd87/0x1ef9 [btrfs]
[<ffffffff81122f53>] ? path_openat+0x234/0x4db
[<ffffffff813c3b78>] ? __do_page_fault+0x31d/0x391
[<ffffffff810f8ab6>] ? vma_link+0x74/0x94
[<ffffffff811250f5>] vfs_ioctl+0x1d/0x39
[<ffffffff811258c8>] do_vfs_ioctl+0x32d/0x3e2
[<ffffffff811259d4>] SyS_ioctl+0x57/0x83
[<ffffffff813c3bfa>] ? do_page_fault+0xe/0x10
[<ffffffff813c73c2>] system_call_fastpath+0x16/0x1b
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* The libaudit test was failing in some systems due to a unescaped newline, fix
it so that the 'trace' tool can be built in such systems.
* Fix installation of libexec components.
* Add default handler for mmap2 events so that tools that don't explicitely
define an MMAP2 handler don't crash, fix from David Ahern.
* Fix to find line information for probe list, from Masami Hiramatsu.
* Set child_pid after perf_evlist__prepare_workload(), fix from Namhyung Kim.
* Fix infinite loop on invalid perf.data file, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull media fixes from Mauro Carvalho Chehab:
- Compilation fixes for GCC < 4.4.6
- one Kbuild dependency select fix (selecting videobuf on msi3101)
- driver fixes on tda10071, e4000, msi3101, soc_camera, s5p-jpeg,
saa7134 and adv7511
- some device quirks needed to make them work properly
- some videobuf2 core regression fixes for some features used only on
embedded drivers
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] saa7134: Fix crash when device is closed before streamoff
[media] adv7511: fix error return code in adv7511_probe()
[media] ths8200: fix compilation with GCC < 4.4.6
[media] ad9389b: fix compilation with GCC < 4.4.6
[media] adv7511: fix compilation with GCC < 4.4.6
[media] adv7842: fix compilation with GCC < 4.4.6
[media] s5p-jpeg: Initialize vfd_decoder->vfl_dir field
[media] videobuf2-dc: Fix support for mappings without struct page in userptr mode
[media] vb2: Allow queuing OUTPUT buffers with zeroed 'bytesused'
[media] mx3-camera: locking cleanup in mx3_videobuf_queue()
[media] sh_vou: almost forever loop in sh_vou_try_fmt_vid_out()
[media] tda10071: change firmware download condition
[media] msi3101: correct max videobuf2 alloc
[media] Add HCL T12Rg-H to STK webcam upside-down table
[media] msi3101: Kconfig select VIDEOBUF2_VMALLOC
[media] msi3101: msi3101_ioctl_ops can be static
[media] e4000: fix PLL calc bug on 32-bit arch
[media] uvcvideo: quirk PROBE_DEF for Microsoft Lifecam NX-3000
[media] uvcvideo: quirk PROBE_DEF for Dell SP2008WFP monitor
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Pull parisc fix from Helge Deller:
"This is a 2-line patch to save the CPU register which holds our task
thread info pointer before calling a firmware function and then to
restore it again afterwards.
This is necessary because on some 64bit machines the high-order 32bits
are being clobbered by the firmware call, and thus we failed to bring
up secondary CPUs (and instead crashed the kernel) in some situations
eg if we had more than 4GB RAM. This patch fixes a bug which has been
since ever in the parisc linux kernel and which prevented some people
to use a 64bit kernel"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM
Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel. The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.
In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.
Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.
So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
info pointer was located above the 4GB boundary.
Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull perf fixes from Ingo Molnar:
"The tree contains three fixes:
- Two tooling fixes
- Reversal of the new 'MMAP2' extended mmap record ABI, introduced in
this merge window. (Patches were proposed to fix it but it was all
a bit late and we felt it's safer to just delay the ABI one more
kernel release and do it right)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Disable PERF_RECORD_MMAP2 support
perf scripting perl: Fix build error on Fedora 12
perf probe: Fix to initialize fname always before use it
Marc Kleine-Budde pointed out, that commit 77cc982 "clocksource: use
clockevents_config_and_register() where possible" caused a regression
for some of the converted subarchs.
The reason is, that the clockevents core code converts the minimal
hardware tick delta to a nanosecond value for core internal
usage. This conversion is affected by integer math rounding loss, so
the backwards conversion to hardware ticks will likely result in a
value which is less than the configured hardware limitation. The
affected subarchs used their own workaround (SIGH!) which got lost in
the conversion.
The solution for the issue at hand is simple: adding evt->mult - 1 to
the shifted value before the integer divison in the core conversion
function takes care of it. But this only works for the case where for
the scaled math mult/shift pair "mult <= 1 << shift" is true. For the
case where "mult > 1 << shift" we can apply the rounding add only for
the minimum delta value to make sure that the backward conversion is
not less than the given hardware limit. For the upper bound we need to
omit the rounding add, because the backwards conversion is always
larger than the original latch value. That would violate the upper
bound of the hardware device.
Though looking closer at the details of that function reveals another
bogosity: The upper bounds check is broken as well. Checking for a
resulting "clc" value greater than KTIME_MAX after the conversion is
pointless. The conversion does:
u64 clc = (latch << evt->shift) / evt->mult;
So there is no sanity check for (latch << evt->shift) exceeding the
64bit boundary. The latch argument is "unsigned long", so on a 64bit
arch the handed in argument could easily lead to an unnoticed shift
overflow. With the above rounding fix applied the calculation before
the divison is:
u64 clc = (latch << evt->shift) + evt->mult - 1;
So we need to make sure, that neither the shift nor the rounding add
is overflowing the u64 boundary.
[ukl: move assignment to rnd after eventually changing mult, fix build
issue and correct comment with the right math]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: nicolas.ferre@atmel.com
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: john.stultz@linaro.org
Cc: kernel@pengutronix.de
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1380052223-24139-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull ACPI and power management fixes from
"These fix two bugs in the intel_pstate driver, a hibernate bug leading
to nasty resume failures sometimes and acpi-cpufreq initialization bug
that causes problems to happen during module unload when intel_pstate
is in use.
Specifics:
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing of
the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory when
the driver cannot be registered and then attempting to unregister
things that have never been registered on exit"
* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi-cpufreq: Fail initialization if driver cannot be registered
PM / hibernate: Move software_resume to late_initcall_sync
intel_pstate: Correct calculation of min pstate value
intel_pstate: Improve accuracy by not truncating until final result
Pull locking fix from Ingo Molnar:
"This tree fixes a boot crash in CONFIG_DEBUG_MUTEXES=y kernels, on
kernels built with GCC 3.x (there are still such distros)"
Side note: it's not just a fix for old gcc versions, it's also removing
an incredibly broken/subtle check that LLVM had issues with, and that
made no sense.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Avoid gcc version dependent __builtin_constant_p() usage
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
" * Fix build error on Fedora 12.
* Fix to initialize fname always before use it, bug introduced
during this merge window, from Masami Hiramatsu.
* Disable PERF_RECORD_MMAP2 support, from Stephane Eranian. "
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull s390 fixes from Martin Schwidefsky:
"Several last minute bug fixes.
Two of them are on the larger side for rc7, the dasd format patch for
older storage devices and the store-clock-fast patch where we have
been to optimistic with an optimization"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/time: correct use of store clock fast
s390/vmlogrdr: fix array access in vmlogrdr_open()
s390/compat,signal: fix return value of copy_siginfo_(to|from)_user32()
s390/dasd: check for availability of prefix command during format
s390/mm,kvm: fix software dirty bits vs. kvm for old machines
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
Commit 040a0a37 ("mutex: Add support for wound/wait style locks")
used "!__builtin_constant_p(p == NULL)" but gcc 3.x cannot
handle such expression correctly, leading to boot failure when
built with CONFIG_DEBUG_MUTEXES=y.
Fix it by explicitly passing a bool which tells whether p != NULL
or not.
[ PeterZ: This is a sad patch, but provided it actually generates
similar code I suppose its the best we can do bar whole
sale deprecating gcc-3. ]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: peterz@infradead.org
Cc: imirkin@alum.mit.edu
Cc: daniel.vetter@ffwll.ch
Cc: robdclark@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/201310171945.AGB17114.FSQVtHOJFOOFML@I-love.SAKURA.ne.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For now, we disable the extended MMAP record support (MMAP2).
We have identified cases where it would not report the correct mapping
information, clone(VM_CLONE) but with separate pids. We will revisit
the support once we find a solution for this case.
The patch changes the kernel to return EINVAL if attr->mmap2 is set. The
patch also modifies the perf tool to use regular PERF_RECORD_MMAP for
synthetic events and it also prevents the tool from requesting
attr->mmap2 mode because the kernel would reject it.
The support will be revisited once the kenrel interface is updated.
In V2, we reduce the patch to the strict minimum.
In V3, we avoid calling perf_event_open() with mmap2 set because we know
it will fail and require fallback retry.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131017173215.GA8820@quad
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull thermal management fixes from Zhang Rui:
"These includes several commits that are necessary to properly fix
regression for TMU test MUX address setting after reset, for exynos
thermal driver.
Specifics:
- fix a regression that the removal of setting a certain field at TMU
configuration setting results in immediately shutdown after reset
on Exynos4412 SoC.
- revert a patch which tries to link the thermal_zone device and its
hwmon node but breaks libsensors.
- fix a deadlock/lockdep warning issue in x86_pkg_temp thermal
driver, which can be reproduced on a buggy platform only.
- fix ti-soc-thermal driver to fall back on bandgap reading when
reading from PCB temperature sensor fails"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Revert "drivers: thermal: parent virtual hwmon with thermal zone"
drivers: thermal: allow ti-soc-thermal run without pcb zone
thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
thermal: exynos: Provide separate TMU data for Exynos4412
thermal: exynos: Remove check for thermal device pointer at exynos_report_trigger()
Thermal: x86_pkg_temp: change spin lock
The result of the store-clock-fast (STCKF) instruction is a bit fuzzy.
It can happen that the value stored on one CPU is smaller than the value
stored on another CPU, although the order of the stores is the other
way around. This can cause deltas of get_tod_clock() values to become
negative when they should not be.
We need to be more careful with store-clock-fast, this patch partially
reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time:
always use stckf instead of stck if available". The get_tod_clock()
function now uses the store-clock-extended (STCKE) instruction.
get_tod_clock_fast() can be used if the fuzziness of store-clock-fast
is acceptable e.g. for wait loops local to a CPU.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
software_resume is being called after deferred_probe_initcall in
drivers base. If the probing of the device that contains the resume
image is deferred, and the system has been instructed to wait for
it to show up, this wait will occur in software_resume. This causes
a deadlock.
Move software_resume into late_initcall_sync so that it happens
after all the other late_initcalls.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Pavel Machek <Pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the late fixes pull request for dmaengine while you fly back
from KS.
We have a new dmaengine ML hosted by vger so a patch for that along
with addition of Dave as driver mainatainer for ioat. Other fixes are
memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
by Sergei"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: edma: fix another memory leak
dma: edma: Fix memory leak
MAINTAINERS: add to ioatdma maintainer list
MAINTAINERS: add the new dmaengine mailing list
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull CIFS fixes from Steve French:
"Five small cifs fixes (includes fixes for: unmount hang, 2 security
related, symlink, large file writes)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ntstatus_to_dos_map[] is not terminated
cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
cifs: Fix inability to write files >2GB to SMB2/3 shares
cifs: Avoid umount hangs with smb2 when server is unresponsive
do not treat non-symlink reparse points as valid symlinks
Pull btrfs fix from Chris Mason:
"Sage hit a deadlock with ceph on btrfs, and Josef tracked it down to a
regression in our initial rc1 pull. When doing nocow writes we were
sometimes starting a transaction with locks held"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: release path before starting transaction in can_nocow_extent
Cast __u64 to u64 to silence this warning on older distros, such as
Fedora 12:
CC /tmp/build/perf/util/scripting-engines/trace-event-perl.o
cc1: warnings being treated as errors
util/scripting-engines/trace-event-perl.c: In function ‘perl_process_tracepoint’:
util/scripting-engines/trace-event-perl.c:285: error: format ‘%lu’ expects type ‘long unsigned int’, but argument 2 has type ‘__u64’
make[1]: *** [/tmp/build/perf/util/scripting-engines/trace-event-perl.o] Error 1
make: *** [install] Error 2
make: Leaving directory `/home/acme/git/linux/tools/perf'
[acme@fedora12 linux]$
Reported-by: Waiman Long <Waiman.Long@hp.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/n/tip-nlxofdqcdjfm0w9o6bgq4kqv@git.kernel.org
Link: http://lkml.kernel.org/r/1381265120-58532-1-git-send-email-Waiman.Long@hp.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix build error in asus_wmi.c when ASUS_WMI=y and ACPI_VIDEO=m
by preventing that combination.
drivers/built-in.o: In function `asus_wmi_probe':
asus-wmi.c:(.text+0x65ddb4): undefined reference to `acpi_video_unregister'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix check within vmlogrdr_open() if the minor address is not larger
than the number of array elements.
Found with "smatch":
drivers/s390/char/vmlogrdr.c:318 vmlogrdr_open() warn:
buffer overflow 'sys_ser' 3 <= 3
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41
As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:
char str1[32] = { 0 };
char str2[32] = { 0 };
int poffset = 10;
int count = 20;
/*open any seq file*/
int fd = open("/proc/modules", O_RDONLY);
pread(fd, str1, count, poffset);
printf("pread:%s\n", str1);
/*seek to where m->read_pos is*/
lseek(fd, poffset+count, SEEK_SET);
/*supposed to read from poffset+count, but this read from position 0*/
read(fd, str2, count);
printf("read:%s\n", str2);
out put:
pread:
ck_netbios_ns 12665
read:
nf_conntrack_netbios
/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000
So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In a recent commit:
commit f455578dd961087a5cf94730d9f6489bb1d355f0
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon Aug 12 14:14:53 2013 -0300
mtd: nand: pxa3xx: Remove hardcoded mtd name
There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.
Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.
While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull driver core fix from Greg KH:
"Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1"
* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
Functions that walk the ntstatus_to_dos_map[] array could
run off the end. For example, ntstatus_to_dos() loops
while ntstatus_to_dos_map[].ntstatus is not 0. Granted,
this is mostly theoretical, but could be used as a DOS attack
if the error code in the SMB header is bogus.
[Might consider adding to stable, as this patch is low risk - Steve]
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Pull ACPI and power management fixes from Rafael Wysocki:
- intel_pstate fix for misbehavior after system resume if sysfs
attributes are set in a specific way before the corresponding suspend
from Dirk Brandewie.
- A recent intel_pstate fix has no effect if unsigned long is 32-bit,
so fix it up to cover that case as well.
- The s3c64xx cpufreq driver was not updated when the index field of
struct cpufreq_frequency_table was replaced with driver_data, so
update it now. From Charles Keepax.
- The Kconfig help text for ACPI_BUTTON still refers to
/proc/acpi/event that has been dropped recently, so modify it to
remove that reference. From Krzysztof Mazur.
- A Lan Tianyu's change adds a missing mutex unlock to an error code
path in acpi_resume_power_resources().
- Some code related to ACPI power resources, whose very purpose is
questionable to put it lightly, turns out to cause problems to happen
during testing on real systems, so remove it completely (we may
revisit that in the future if there's a compelling enough reason).
From Rafael J Wysocki and Aaron Lu.
* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
cpufreq: s3c64xx: Rename index to driver_data
ACPI / power: Drop automaitc resume of power resource dependent devices
intel_pstate: Fix type mismatch warning
cpufreq / intel_pstate: Fix max_perf_pct on resume
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
Fix perf probe --list to initialize fname local var always before
use it. This may cause a SEGV if there is a probe which is in
the function body but not in any inline function.
Problem introduced in:
commit e08cfd4bda76
Author: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Date: Mon Sep 30 18:21:44 2013 +0900
perf probe: Fix to find line information for probe list
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20131011122317.9662.29736.stgit@kbuild-fedora.novalocal
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit b82715fdd4a5407f56853b24d387d484dd9c3b5b introduces
a 'device' subdirectory under /sys/class/hwmon/hwmonX/ directory,
for the thermal_zone hwmon devices. And this results in different
handling by libsensors.
The problem is reported and discussed in this thread
http://marc.info/?l=linux-pm&m=138229306109596&w=2
This patch reverts commit b82715fdd4a5407f56853b24d387d484dd9c3b5b.
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
x86_pkg_temp receives thermal notifications via a callback from a
therm_throt driver, where thermal interrupts are processed.
This callback is pkg_temp_thermal_platform_thermal_notify. Here to
avoid multiple interrupts from cores in a package, we disable the
source and also set a variable to avoid scheduling delayed work function.
This variable is protected via spin_lock_irqsave. On one buggy platform,
we still receiving interrupts even if the source is disabled. This
can cause deadlock/lockdep warning, when interrupt is generated while under
spinlock in work function.
Change spin_lock to spin_lock_irqsave and spin_unlock to
spin_unlock_irqrestore as the data it is trying to protect can also
be modified in a notification call called from interrupt handler.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The return value of copy_siginfo_(to|from)_user32() gets passed to
user space, however we do not convert a positive return value from
copy_(to|from)_user to -EFAULT.
Therefore these functions (and the calling system calls) my incorrectly
return a positive number (bytes not copied) instead of -EFAULT.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull ecryptfs fixes from Tyler Hicks:
"Two important fixes
- Fix long standing memory leak in the (rarely used) public key
support
- Fix large file corruption on 32 bit architectures"
* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: fix 32 bit corruption issue
ecryptfs: Fix memory leakage in keystore.c
Background: nfsd v[23] had throughput regression since delayed fput
went in; every read or write ends up doing fput() and we get a pair
of extra context switches out of that (plus quite a bit of work
in queue_work itselfi, apparently). Use of schedule_delayed_work()
gives it a chance to accumulate a bit before we do __fput() on all
of them. I'm not too happy about that solution, but... on at least
one real-world setup it reverts about 10% throughput loss we got from
switch to delayed fput.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull MTD fixes from Brian Norris:
- fix a small memory leak in some new ONFI code
- account for additional odd variations of Micron SPI flash
Acked by David Woodhouse.
* tag 'for-linus-20131008' of git://git.infradead.org/linux-mtd:
mtd: m25p80: Fix 4 byte addressing mode for Micron devices.
mtd: nand: fix memory leak in ONFI extended parameter page
This patch addresses Bug 60727
(https://bugzilla.kernel.org/show_bug.cgi?id=60727)
which was due to the truncation of intermediate values in the
calculations, which causes the code to consistently underestimate the
current cpu frequency, specifically 100% cpu utilization was truncated
down to the setpoint of 97%. This patch fixes the problem by keeping
the results of all intermediate calculations as fixed point numbers
rather scaling them back and forth between integers and fixed point.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60727
Signed-off-by: Brennan Shacklett <bpshacklett@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds an explicit check + failure for XCOPY I/O to source +
destination devices with a non-matching block_size.
This limitiation is currently due to the fact that the scatterlist
memory allocated for the XCOPY READ operation is passed zero-copy
to the XCOPY WRITE operation.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
When inserting a wrong value to /sys/devices/system/memory/memoryX/state file,
following messages are shown. And device_hotplug_lock is never released.
================================================
[ BUG: lock held when returning to user space! ]
3.12.0-rc4-debug+ #3 Tainted: G W
------------------------------------------------
bash/6442 is leaving the kernel with locks still held!
1 lock held by bash/6442:
#0: (device_hotplug_lock){+.+.+.}, at: [<ffffffff8146cbb5>] lock_device_hotplug_sysfs+0x15/0x50
This issue was introdued by commit fa2be40 (drivers: base: use standard
device online/offline for state change).
This patch releases device_hotplug_lcok when store_mem_state returns EINVAL.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
CC: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows users to use LANMAN authentication on servers which support
unencapsulated authentication.
The patch fixes a regression where users using plaintext authentication
were no longer able to do so because of changed bought in by patch
3f618223dc0bdcbc8d510350e78ee2195ff93768
https://bugzilla.redhat.com/show_bug.cgi?id=1011621
Reported-by: Panos Kavalagios <Panagiotis.Kavalagios@eurodyn.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
* acpi-fixes:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
ACPI / power: Drop automaitc resume of power resource dependent devices
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
When doing space balance and subvolume destroy at the same time, we met
the following oops:
kernel BUG at fs/btrfs/relocation.c:2247!
RIP: 0010: [<ffffffffa04cec16>] prepare_to_merge+0x154/0x1f0 [btrfs]
Call Trace:
[<ffffffffa04b5ab7>] relocate_block_group+0x466/0x4e6 [btrfs]
[<ffffffffa04b5c7a>] btrfs_relocate_block_group+0x143/0x275 [btrfs]
[<ffffffffa0495c56>] btrfs_relocate_chunk.isra.27+0x5c/0x5a2 [btrfs]
[<ffffffffa0459871>] ? btrfs_item_key_to_cpu+0x15/0x31 [btrfs]
[<ffffffffa048b46a>] ? btrfs_get_token_64+0x7e/0xcd [btrfs]
[<ffffffffa04a3467>] ? btrfs_tree_read_unlock_blocking+0xb2/0xb7 [btrfs]
[<ffffffffa049907d>] btrfs_balance+0x9c7/0xb6f [btrfs]
[<ffffffffa049ef84>] btrfs_ioctl_balance+0x234/0x2ac [btrfs]
[<ffffffffa04a1e8e>] btrfs_ioctl+0xd87/0x1ef9 [btrfs]
[<ffffffff81122f53>] ? path_openat+0x234/0x4db
[<ffffffff813c3b78>] ? __do_page_fault+0x31d/0x391
[<ffffffff810f8ab6>] ? vma_link+0x74/0x94
[<ffffffff811250f5>] vfs_ioctl+0x1d/0x39
[<ffffffff811258c8>] do_vfs_ioctl+0x32d/0x3e2
[<ffffffff811259d4>] SyS_ioctl+0x57/0x83
[<ffffffff813c3bfa>] ? do_page_fault+0xe/0x10
[<ffffffff813c73c2>] system_call_fastpath+0x16/0x1b
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* The libaudit test was failing in some systems due to a unescaped newline, fix
it so that the 'trace' tool can be built in such systems.
* Fix installation of libexec components.
* Add default handler for mmap2 events so that tools that don't explicitely
define an MMAP2 handler don't crash, fix from David Ahern.
* Fix to find line information for probe list, from Masami Hiramatsu.
* Set child_pid after perf_evlist__prepare_workload(), fix from Namhyung Kim.
* Fix infinite loop on invalid perf.data file, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull media fixes from Mauro Carvalho Chehab:
- Compilation fixes for GCC < 4.4.6
- one Kbuild dependency select fix (selecting videobuf on msi3101)
- driver fixes on tda10071, e4000, msi3101, soc_camera, s5p-jpeg,
saa7134 and adv7511
- some device quirks needed to make them work properly
- some videobuf2 core regression fixes for some features used only on
embedded drivers
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] saa7134: Fix crash when device is closed before streamoff
[media] adv7511: fix error return code in adv7511_probe()
[media] ths8200: fix compilation with GCC < 4.4.6
[media] ad9389b: fix compilation with GCC < 4.4.6
[media] adv7511: fix compilation with GCC < 4.4.6
[media] adv7842: fix compilation with GCC < 4.4.6
[media] s5p-jpeg: Initialize vfd_decoder->vfl_dir field
[media] videobuf2-dc: Fix support for mappings without struct page in userptr mode
[media] vb2: Allow queuing OUTPUT buffers with zeroed 'bytesused'
[media] mx3-camera: locking cleanup in mx3_videobuf_queue()
[media] sh_vou: almost forever loop in sh_vou_try_fmt_vid_out()
[media] tda10071: change firmware download condition
[media] msi3101: correct max videobuf2 alloc
[media] Add HCL T12Rg-H to STK webcam upside-down table
[media] msi3101: Kconfig select VIDEOBUF2_VMALLOC
[media] msi3101: msi3101_ioctl_ops can be static
[media] e4000: fix PLL calc bug on 32-bit arch
[media] uvcvideo: quirk PROBE_DEF for Microsoft Lifecam NX-3000
[media] uvcvideo: quirk PROBE_DEF for Dell SP2008WFP monitor
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>