tjh.dev
commits
Drain the Microcode TX-status-FIFO before we enable IRQs.
This is required, because the FIFO may still have entries left
from a previous run. Those would immediately fire after enabling
IRQs and would lead to an oops in the DMA TXstatus handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.
This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix EV64120 and Ocelot builds by providing a plat_timer_setup().
[MIPS] EV64120: Fix PCI interrupt allocation.
[MIPS] Make irq number allocator generally available for fixing EV64120.
[MIPS] EV64120: Fix timer initialization for HZ != 100.
[MIPS] Ocelot 3: Fix MAC address detection after platform_device conversion.
[MIPS] Ocelot C: Fix MAC address detection after platform_device conversion.
[MIPS] SB1: On bootup only flush cache on local CPU.
[MIPS] Ocelot 3: Fix large number of warnings.
[MIPS] Ocelot C: Fix mapping of ioport address range.
[MIPS] Ocelot C: Fix warning about missmatching format string.
[MIPS] Ocelot C: fix eth registration after conversion to platform_device
[MIPS] Ocelot C: Fix large number of warnings.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4751): Fix DBV_FE_CUSTOMISE for card drivers compiled into kernel
V4L/DVB (4784): [saa7146_i2c] short_delay mode fixed for fast machines
V4L/DVB (4770): Fix mode switch of Compro Videomate T300
V4L/DVB (4787): Budget-ci: Inversion setting fixed for Technotrend 1500 T
V4L/DVB (4786): Pvrusb2: use NULL instead of 0
V4L/DVB (4785): Budget-ci: Change DEBIADDR_IR to a safer default
V4L/DVB (4752): DVB: Add DVB_FE_CUSTOMISE support for MT2060
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[DLM] fix oops in kref_put when removing a lockspace
[DLM] Fix kref_put oops
[GFS2] Fix OOM error handling
[GFS2] Fix incorrect fs sync behaviour.
[GFS2] don't panic needlessly
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
AVR32: Add missing return instruction in __raw_writesb
AVR32: Wire up sys_epoll_pwait
AVR32: Fix thinko in generic_find_next_zero_le_bit()
AVR32: Get rid of board_early_init
Now that the lockspace struct is freed when the last sysfs object is released
this patch prevents use of that lockspace by sysfs. We attempt to re-get the
lockspace from the lockspace list and fail the request if it has been removed.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
TT DVB-C 2300 runs at 137 kHz I2C speed. short_delay mode did not work
reliably on fast machines with that speed. Increased max loop count from
20 to 50. Moved dummy access out of the loop.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] IRQs too early enabled.
[S390] revert add_active_range() usage patch.
__raw_writesb ends with a conditional branch, which is obviously
wrong. It should return after the last loop terminates.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch fixes the recounting on the lockspace kobject. Previously the lockspace was freed while userspace could have had a
reference to one of its sysfs files, causing an oops in kref_put.
Now the lockspace kfree is moved into the kobject release() function
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The board did not return to analog mode since the board specific
"demod sleep" function was not called.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Kconfig: remove redundant NETDEVICES depends
[PATCH] ehea: 64K page support fix
[PATCH] ehea: Removed redundant define
[PATCH] ehea: Nullpointer dereferencation fix
[PATCH] bcm43xx: fix unexpected LED control values in BCM4303 sprom
[PATCH] bcm43xx: Fix low-traffic netdev watchdog TX timeouts
[PATCH] hostap_plx: fix CIS verification
[PATCH] ieee80211: don't flood log with errors
setup_lowcore() calls ctl_set_bit() which returns withs interrupts
enabled. The setup arch code is not supposed to enable interrupts that
early. Therefore use the __ctl_set_bit() variant.
This fixes the not working lock dependency validator on non 64 bit
systems.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix the OOM error handling in inode.c where it was possible for
a NULL pointer to be dereferenced.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
auth_domain_put() forgot to unlock acquired spinlock.
Cc: Olaf Kirch <okir@monad.swb.de>
Cc: Andy Adamson <andros@citi.umich.edu>
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 7676bef9c183fd573822cac9992927ef596d584c breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The existing implementation of this function seems to be looking for
a one although it should be looking for a zero. This causes trouble
for the ext2 filesystem, which tends to report -ENOSPC without this
patch.
Fix this by complementing each word before scanning.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds a sync_fs superblock operation for GFS2 and removes
the journal flush from write_super in favour of sync_fs where it
ought to be. This is more or less identical to the way in which ext3
does this.
This bug was pointed out by Russell Cattelan <cattelan@redhat.com>
Cc: Russell Cattelan <cattelan@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Fix sparse NULL usage warnings:
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:714:14: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:715:16: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1079:10: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:224:58: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch takes the CTL_UNNUMBERD concept from NFS and makes it available to
all new sysctl users.
At the same time the sysctl binary interface maintenance documentation is
updated to mention and to describe what is needed to successfully maintain the
sysctl binary interface.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/Kconfig says:
# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
so remove duplicate 'depends' uses of NETDEVICES.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETLABEL]: Fix build failure.
[IPV6]: Give sit driver an appropriate module alias.
[IPV6]: Add ndisc_netdev_notifier unregister.
[NET]: __alloc_pages() failures reported due to fragmentation
[PKTGEN]: TCI endianness fixes
[TG3]: Fix 2nd ifup failure on 5752M.
[NETFILTER] bug: skb->protocol is already net-endian
[NETFILTER] bug: nfulnl_msg_config_mode ->copy_range is 32bit
[NETFILTER] bug: NFULA_CFG_QTHRESH uses 32bit
[IPV6]: Fix ECN bug on big-endian
[IPX]: Annotate and fix IPX checksum
[IPX]: Trivial parts of endianness annotations
board_early_init() is left over from some early prototyping work
where we had to initialize the SDRAM controller ourselves. This
depends on the kernel being loaded into static RAM, which just
isn't possible on any commercially available products today.
In order to run without a boot loader, we need to create a zImage
stub or have the debugger initialize the SDRAM for us (for really
low-level debugging)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
First, SLAB_PANIC is unjustified. Second, all error propagating and backing out
is in place.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David H�rdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This fixes a warning on bootup warning in smp_call_function.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since it is becoming clear that there are just enough users of the binary
sysctl interface that completely removing the binary interface from the kernel
will not be an option for foreseeable future, we need to find a way to address
the sysctl maintenance issues.
The basic problem is that sysctl requires one central authority to allocate
sysctl numbers, or else conflicts and ABI breakage occur. The proc interface
to sysctl does not have that problem, as names are not densely allocated.
By not terminating a sysctl table until I have neither a ctl_name nor a
procname, it becomes simple to add sysctl entries that don't show up in the
binary sysctl interface. Which allows people to avoid allocating a binary
sysctl value when not needed.
I have audited the kernel code and in my reading I have not found a single
sysctl table that wasn't terminated by a completely zero filled entry. So
this change in behavior should not affect anything.
I think this mechanism eases the pain enough that combined with a little
disciple we can solve the reoccurring sysctl ABI breakage.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes 64k page support by using PAGE_MASK and appropriate pagesize defines in several places.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added the entries for the robust futex syscall entries, I
forgot to bump NR_SYSCALLS. The current situation is error-prone
because NR_SYSCALLS lives in entry.S where the system call limit
checks are enforced. Move the definition to asm/unistd.h in order to
make this mistake much more difficult to make.
And wire up sys_migrate_pages since the powerpc folks implemented the
compat wrapper for us.
Signed-off-by: David S. Miller <davem@davemloft.net>
> the build with the attached .config failed, make ends with:
> ...
> : undefined reference to `cipso_v4_sock_getattr'
> net/built-in.o: In function `netlbl_socket_getattr':
...
It looks like I was stupid and made NetLabel depend on CONFIG_NET and not
CONFIG_INET, the patch below should fix this by making NetLabel depend on
CONFIG_INET and CONFIG_SECURITY. Please review and apply for 2.6.19.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the MT2060 be customized like most of the other DVB PLLs/front-ends.
Also, add a missing dependency on I2C.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Don't warn about libpthread's access to kernel.version. When it receives
-ENOSYS it will read /proc/sys/kernel/version.
If anything else shows up print the sysctl number string.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cal Peake <cp@absolutedigital.net>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed define H_CB_ALIGNMENT which is already defined in include/asm-powerpc/hvcall.h
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous commit (45c18b0bb579b5c1b89f8c99f1b6ffa4c586ba08, aka "Fix
unlikely (but possible) race condition on task->user access") fixed a
potential oops due to __sigqueue_alloc() getting its "user" pointer out
of sync with switch_user(), and accessing a user pointer that had been
de-allocated on another CPU.
It still left another (much less serious) problem, where a concurrent
__sigqueue_alloc and swich_user could cause sigqueue_alloc to do signal
pending reference counting for a _different_ user than the one it then
actually ended up using. No oops, but we'd end up with the wrong signal
accounting.
Another case of Oleg's eagle-eyes picking up the problem.
This is trivially fixed by just making sure we load whichever "user"
structure we decide to use (it doesn't matter _which_ one we pick, we
just need to pick one) just once.
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would be nice to keep things working even with this built as a
module, it took me some time to realize my IPv6 tunnel was broken
because of the missing sit module. This module alias fixes things
until distributions have added an appropriate alias to modprobe.conf.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pci_ids.h: Add NVIDIA PCI ID
o Fix warnings
o 768MB worth of I/O ports were insane
o 64-bit kernels don't need special handling because ioremap does the magic
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the delayacct lock irqsave; this avoids the possible deadlock where
an interrupt is taken while holding the delayacct lock which needs to
take the delayacct lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix: Must check for nullpointer before dereferencing it - not afterwards.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The "ieee80211: Workaround malformed 802.11 frames from AP" patch (see
http://kernel.org/git/?p=linux/kernel/git/linville/wireless-2.6.git;a=commit;h=f09fc44d8c25f22c4d985bb93857338ed02feac6 )
fixes the problem with some buggy APs but also converts debug message into
an error one. This floods the log with errors when you are near such AP (you
get a message for every beacon). This patch reverts the error message back
to the debug one.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a possible race condition when doing a "switch_uid()" from one
user to another, which could race with another thread doing a signal
allocation and looking at the old thread ->user pointer as it is freed.
This explains an oops reported by Lukasz Trabinski:
http://permalink.gmane.org/gmane.linux.kernel/462241
We fix this by delaying the (reference-counted) freeing of the user
structure until the thread signal handler lock has been released, so
that we know that the signal allocation has either seen the new value or
has properly incremented the reference count of the old one.
Race identified by Oleg Nesterov.
Cc: Lukasz Trabinski <lukasz@wsisiz.edu.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If inet6_init() fails later than ndisc_init() call, or IPv6 module is
unloaded, ndisc_netdev_notifier call remains in the list and will follows in
oops later.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] report rename failure when target file is locked by Windows
[CIFS] Allow null user connections
[CIFS] Fix readdir breakage when blocksize set too small
Drain the Microcode TX-status-FIFO before we enable IRQs.
This is required, because the FIFO may still have entries left
from a previous run. Those would immediately fire after enabling
IRQs and would lead to an oops in the DMA TXstatus handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.
This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix EV64120 and Ocelot builds by providing a plat_timer_setup().
[MIPS] EV64120: Fix PCI interrupt allocation.
[MIPS] Make irq number allocator generally available for fixing EV64120.
[MIPS] EV64120: Fix timer initialization for HZ != 100.
[MIPS] Ocelot 3: Fix MAC address detection after platform_device conversion.
[MIPS] Ocelot C: Fix MAC address detection after platform_device conversion.
[MIPS] SB1: On bootup only flush cache on local CPU.
[MIPS] Ocelot 3: Fix large number of warnings.
[MIPS] Ocelot C: Fix mapping of ioport address range.
[MIPS] Ocelot C: Fix warning about missmatching format string.
[MIPS] Ocelot C: fix eth registration after conversion to platform_device
[MIPS] Ocelot C: Fix large number of warnings.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4751): Fix DBV_FE_CUSTOMISE for card drivers compiled into kernel
V4L/DVB (4784): [saa7146_i2c] short_delay mode fixed for fast machines
V4L/DVB (4770): Fix mode switch of Compro Videomate T300
V4L/DVB (4787): Budget-ci: Inversion setting fixed for Technotrend 1500 T
V4L/DVB (4786): Pvrusb2: use NULL instead of 0
V4L/DVB (4785): Budget-ci: Change DEBIADDR_IR to a safer default
V4L/DVB (4752): DVB: Add DVB_FE_CUSTOMISE support for MT2060
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the lockspace struct is freed when the last sysfs object is released
this patch prevents use of that lockspace by sysfs. We attempt to re-get the
lockspace from the lockspace list and fail the request if it has been removed.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes the recounting on the lockspace kobject. Previously the lockspace was freed while userspace could have had a
reference to one of its sysfs files, causing an oops in kref_put.
Now the lockspace kfree is moved into the kobject release() function
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Kconfig: remove redundant NETDEVICES depends
[PATCH] ehea: 64K page support fix
[PATCH] ehea: Removed redundant define
[PATCH] ehea: Nullpointer dereferencation fix
[PATCH] bcm43xx: fix unexpected LED control values in BCM4303 sprom
[PATCH] bcm43xx: Fix low-traffic netdev watchdog TX timeouts
[PATCH] hostap_plx: fix CIS verification
[PATCH] ieee80211: don't flood log with errors
setup_lowcore() calls ctl_set_bit() which returns withs interrupts
enabled. The setup arch code is not supposed to enable interrupts that
early. Therefore use the __ctl_set_bit() variant.
This fixes the not working lock dependency validator on non 64 bit
systems.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
auth_domain_put() forgot to unlock acquired spinlock.
Cc: Olaf Kirch <okir@monad.swb.de>
Cc: Andy Adamson <andros@citi.umich.edu>
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 7676bef9c183fd573822cac9992927ef596d584c breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The existing implementation of this function seems to be looking for
a one although it should be looking for a zero. This causes trouble
for the ext2 filesystem, which tends to report -ENOSPC without this
patch.
Fix this by complementing each word before scanning.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds a sync_fs superblock operation for GFS2 and removes
the journal flush from write_super in favour of sync_fs where it
ought to be. This is more or less identical to the way in which ext3
does this.
This bug was pointed out by Russell Cattelan <cattelan@redhat.com>
Cc: Russell Cattelan <cattelan@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Fix sparse NULL usage warnings:
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:714:14: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:715:16: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1079:10: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:224:58: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch takes the CTL_UNNUMBERD concept from NFS and makes it available to
all new sysctl users.
At the same time the sysctl binary interface maintenance documentation is
updated to mention and to describe what is needed to successfully maintain the
sysctl binary interface.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETLABEL]: Fix build failure.
[IPV6]: Give sit driver an appropriate module alias.
[IPV6]: Add ndisc_netdev_notifier unregister.
[NET]: __alloc_pages() failures reported due to fragmentation
[PKTGEN]: TCI endianness fixes
[TG3]: Fix 2nd ifup failure on 5752M.
[NETFILTER] bug: skb->protocol is already net-endian
[NETFILTER] bug: nfulnl_msg_config_mode ->copy_range is 32bit
[NETFILTER] bug: NFULA_CFG_QTHRESH uses 32bit
[IPV6]: Fix ECN bug on big-endian
[IPX]: Annotate and fix IPX checksum
[IPX]: Trivial parts of endianness annotations
board_early_init() is left over from some early prototyping work
where we had to initialize the SDRAM controller ourselves. This
depends on the kernel being loaded into static RAM, which just
isn't possible on any commercially available products today.
In order to run without a boot loader, we need to create a zImage
stub or have the debugger initialize the SDRAM for us (for really
low-level debugging)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David H�rdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since it is becoming clear that there are just enough users of the binary
sysctl interface that completely removing the binary interface from the kernel
will not be an option for foreseeable future, we need to find a way to address
the sysctl maintenance issues.
The basic problem is that sysctl requires one central authority to allocate
sysctl numbers, or else conflicts and ABI breakage occur. The proc interface
to sysctl does not have that problem, as names are not densely allocated.
By not terminating a sysctl table until I have neither a ctl_name nor a
procname, it becomes simple to add sysctl entries that don't show up in the
binary sysctl interface. Which allows people to avoid allocating a binary
sysctl value when not needed.
I have audited the kernel code and in my reading I have not found a single
sysctl table that wasn't terminated by a completely zero filled entry. So
this change in behavior should not affect anything.
I think this mechanism eases the pain enough that combined with a little
disciple we can solve the reoccurring sysctl ABI breakage.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added the entries for the robust futex syscall entries, I
forgot to bump NR_SYSCALLS. The current situation is error-prone
because NR_SYSCALLS lives in entry.S where the system call limit
checks are enforced. Move the definition to asm/unistd.h in order to
make this mistake much more difficult to make.
And wire up sys_migrate_pages since the powerpc folks implemented the
compat wrapper for us.
Signed-off-by: David S. Miller <davem@davemloft.net>
> the build with the attached .config failed, make ends with:
> ...
> : undefined reference to `cipso_v4_sock_getattr'
> net/built-in.o: In function `netlbl_socket_getattr':
...
It looks like I was stupid and made NetLabel depend on CONFIG_NET and not
CONFIG_INET, the patch below should fix this by making NetLabel depend on
CONFIG_INET and CONFIG_SECURITY. Please review and apply for 2.6.19.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't warn about libpthread's access to kernel.version. When it receives
-ENOSYS it will read /proc/sys/kernel/version.
If anything else shows up print the sysctl number string.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cal Peake <cp@absolutedigital.net>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous commit (45c18b0bb579b5c1b89f8c99f1b6ffa4c586ba08, aka "Fix
unlikely (but possible) race condition on task->user access") fixed a
potential oops due to __sigqueue_alloc() getting its "user" pointer out
of sync with switch_user(), and accessing a user pointer that had been
de-allocated on another CPU.
It still left another (much less serious) problem, where a concurrent
__sigqueue_alloc and swich_user could cause sigqueue_alloc to do signal
pending reference counting for a _different_ user than the one it then
actually ended up using. No oops, but we'd end up with the wrong signal
accounting.
Another case of Oleg's eagle-eyes picking up the problem.
This is trivially fixed by just making sure we load whichever "user"
structure we decide to use (it doesn't matter _which_ one we pick, we
just need to pick one) just once.
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would be nice to keep things working even with this built as a
module, it took me some time to realize my IPv6 tunnel was broken
because of the missing sit module. This module alias fixes things
until distributions have added an appropriate alias to modprobe.conf.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the delayacct lock irqsave; this avoids the possible deadlock where
an interrupt is taken while holding the delayacct lock which needs to
take the delayacct lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "ieee80211: Workaround malformed 802.11 frames from AP" patch (see
http://kernel.org/git/?p=linux/kernel/git/linville/wireless-2.6.git;a=commit;h=f09fc44d8c25f22c4d985bb93857338ed02feac6 )
fixes the problem with some buggy APs but also converts debug message into
an error one. This floods the log with errors when you are near such AP (you
get a message for every beacon). This patch reverts the error message back
to the debug one.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a possible race condition when doing a "switch_uid()" from one
user to another, which could race with another thread doing a signal
allocation and looking at the old thread ->user pointer as it is freed.
This explains an oops reported by Lukasz Trabinski:
http://permalink.gmane.org/gmane.linux.kernel/462241
We fix this by delaying the (reference-counted) freeing of the user
structure until the thread signal handler lock has been released, so
that we know that the signal allocation has either seen the new value or
has properly incremented the reference count of the old one.
Race identified by Oleg Nesterov.
Cc: Lukasz Trabinski <lukasz@wsisiz.edu.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>