Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.

Another week, another batch of fixes for arm-soc platforms.

Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703

arch/arm/boot/dts/am33xx.dtsi

···
 			ti,hwmods = "gpmc";
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
-			num-cs = <7>;
-			num-waitpins = <2>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
 			status = "disabled";

arch/arm/boot/dts/armada-xp-gp.dts

···
 	};
 
 	soc {
-		ranges = <0          0 0xd0000000 0x100000
-			  0xf0000000 0 0xf0000000 0x1000000>;
+		ranges = <0          0 0xd0000000 0x100000  /* Internal registers 1MiB */
+			  0xe0000000 0 0xe0000000 0x8100000 /* PCIe */
+			  0xf0000000 0 0xf0000000 0x1000000 /* Device Bus, NOR 16MiB  */>;
 
 		internal-regs {
 			serial@12000 {

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

···
 	};
 
 	soc {
-		ranges = <0          0 0xd0000000 0x100000
-			  0xf0000000 0 0xf0000000 0x8000000>;
+		ranges = <0          0 0xd0000000 0x100000	/* Internal registers 1MiB */
+			  0xe0000000 0 0xe0000000 0x8100000     /* PCIe */
+			  0xf0000000 0 0xf0000000 0x8000000     /* Device Bus, NOR 128MiB   */>;
 
 		internal-regs {
 			serial@12000 {

arch/arm/boot/dts/omap4-panda-common.dtsi

···
 	};
 };
 
+&omap4_pmx_wkup {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6030_wkup_pins
+	>;
+
+	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+		pinctrl-single,pins = <
+			0x14 0x2        /* fref_clk0_out.sys_drm_msecure OUTPUT | MODE2 */
+		>;
+	};
+};
+
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
+			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&mcbsp1_pins
 			&dss_hdmi_pins
 			&tpd12s015_pins
 	>;
+
+	twl6030_pins: pinmux_twl6030_pins {
+		pinctrl-single,pins = <
+			0x15e 0x4118	/* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */
+		>;
+	};
 
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <

arch/arm/boot/dts/omap4-sdp.dts

···
 	};
 };
 
+&omap4_pmx_wkup {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6030_wkup_pins
+	>;
+
+	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+		pinctrl-single,pins = <
+			0x14 0x2        /* fref_clk0_out.sys_drm_msecure OUTPUT | MODE2 */
+		>;
+	};
+};
+
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
+			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&dmic_pins
···
 		pinctrl-single,pins = <
 			0x11c 0x100	/* uart4_rx.uart4_rx INPUT | MODE0 */
 			0x11e 0		/* uart4_tx.uart4_tx OUTPUT | MODE0 */
+		>;
+	};
+
+	twl6030_pins: pinmux_twl6030_pins {
+		pinctrl-single,pins = <
+			0x15e 0x4118	/* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */
 		>;
 	};
 

arch/arm/boot/dts/omap5.dtsi

···
 			interrupts = <0 41 0x4>;
 			ti,hwmods = "timer5";
 			ti,timer-dsp;
+			ti,timer-pwm;
 		};
 
 		timer6: timer@4013a000 {
···
 			reg = <0x4803e000 0x80>;
 			interrupts = <0 45 0x4>;
 			ti,hwmods = "timer9";
+			ti,timer-pwm;
 		};
 
 		timer10: timer@48086000 {
···
 			reg = <0x48086000 0x80>;
 			interrupts = <0 46 0x4>;
 			ti,hwmods = "timer10";
+			ti,timer-pwm;
 		};
 
 		timer11: timer@48088000 {

arch/arm/mach-kirkwood/mpp.c

···
 
 	kirkwood_pcie_id(&dev, &rev);
 
-	if ((dev == MV88F6281_DEV_ID && rev >= MV88F6281_REV_A0) ||
-	    (dev == MV88F6282_DEV_ID))
+	if (dev == MV88F6281_DEV_ID && rev >= MV88F6281_REV_A0)
 		return MPP_F6281_MASK;
+	if (dev == MV88F6282_DEV_ID)
+		return MPP_F6282_MASK;
 	if (dev == MV88F6192_DEV_ID && rev >= MV88F6192_REV_A0)
 		return MPP_F6192_MASK;
 	if (dev == MV88F6180_DEV_ID)

arch/arm/mach-omap2/clock36xx.c

···
 
 #include <linux/kernel.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/io.h>
 
 #include "clock.h"
 #include "clock36xx.h"
-
+#define to_clk_divider(_hw) container_of(_hw, struct clk_divider, hw)
 
 /**
  * omap36xx_pwrdn_clk_enable_with_hsdiv_restore - enable clocks suffering
···
  */
 int omap36xx_pwrdn_clk_enable_with_hsdiv_restore(struct clk_hw *clk)
 {
-	struct clk_hw_omap *parent;
+	struct clk_divider *parent;
 	struct clk_hw *parent_hw;
-	u32 dummy_v, orig_v, clksel_shift;
+	u32 dummy_v, orig_v;
 	int ret;
 
 	/* Clear PWRDN bit of HSDIVIDER */
 	ret = omap2_dflt_clk_enable(clk);
 
 	parent_hw = __clk_get_hw(__clk_get_parent(clk->clk));
-	parent = to_clk_hw_omap(parent_hw);
+	parent = to_clk_divider(parent_hw);
 
 	/* Restore the dividers */
 	if (!ret) {
-		clksel_shift = __ffs(parent->clksel_mask);
-		orig_v = __raw_readl(parent->clksel_reg);
+		orig_v = __raw_readl(parent->reg);
 		dummy_v = orig_v;
 
 		/* Write any other value different from the Read value */
-		dummy_v ^= (1 << clksel_shift);
-		__raw_writel(dummy_v, parent->clksel_reg);
+		dummy_v ^= (1 << parent->shift);
+		__raw_writel(dummy_v, parent->reg);
 
 		/* Write the original divider */
-		__raw_writel(orig_v, parent->clksel_reg);
+		__raw_writel(orig_v, parent->reg);
 	}
 
 	return ret;

arch/arm/mach-omap2/omap_hwmod_33xx_data.c

···
 	},
 };
 
+/* uart2 */
+static struct omap_hwmod_dma_info uart2_edma_reqs[] = {
+	{ .name = "tx",	.dma_req = 28, },
+	{ .name = "rx",	.dma_req = 29, },
+	{ .dma_req = -1 }
+};
+
 static struct omap_hwmod_irq_info am33xx_uart2_irqs[] = {
 	{ .irq = 73 + OMAP_INTC_START, },
 	{ .irq = -1 },
···
 	.clkdm_name	= "l4ls_clkdm",
 	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart2_irqs,
-	.sdma_reqs	= uart1_edma_reqs,
+	.sdma_reqs	= uart2_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
 	.prcm		= {
 		.omap4	= {

arch/arm/mach-omap2/pm34xx.c

···
 	/* Clear any pending PRCM interrupts */
 	omap2_prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
-	if (omap3_has_iva())
-		omap3_iva_idle();
+	/*
+	 * We need to idle iva2_pwrdm even on am3703 with no iva2.
+	 */
+	omap3_iva_idle();
 
 	omap3_d2d_idle();
 }

arch/arm/mach-prima2/pm.c

···
 	struct device_node *np;
 
 	np = of_find_matching_node(NULL, pwrc_ids);
-	if (!np)
-		panic("unable to find compatible pwrc node in dtb\n");
+	if (!np) {
+		pr_err("unable to find compatible sirf pwrc node in dtb\n");
+		return -ENOENT;
+	}
 
 	/*
 	 * pwrc behind rtciobrg is not located in memory space

arch/arm/mach-prima2/rstc.c

···
 	struct device_node *np;
 
 	np = of_find_matching_node(NULL, rstc_ids);
-	if (!np)
-		panic("unable to find compatible rstc node in dtb\n");
+	if (!np) {
+		pr_err("unable to find compatible sirf rstc node in dtb\n");
+		return -ENOENT;
+	}
 
 	sirfsoc_rstc_base = of_iomap(np, 0);
 	if (!sirfsoc_rstc_base)

arch/arm/plat-samsung/pm.c

···
 #include <linux/suspend.h>
 #include <linux/errno.h>
 #include <linux/delay.h>
+#include <linux/of.h>
 #include <linux/serial_core.h>
 #include <linux/io.h>
 
···
 	 * require a full power-cycle)
 	*/
 
-	if (!any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
+	if (!of_have_populated_dt() &&
+	    !any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
 	    !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
 		printk(KERN_ERR "%s: No wake-up sources!\n", __func__);
 		printk(KERN_ERR "%s: Aborting sleep\n", __func__);
···
 
 	/* save all necessary core registers not covered by the drivers */
 
-	samsung_pm_save_gpios();
-	samsung_pm_saved_gpios();
+	if (!of_have_populated_dt()) {
+		samsung_pm_save_gpios();
+		samsung_pm_saved_gpios();
+	}
+
 	s3c_pm_save_uarts();
 	s3c_pm_save_core();
 
···
 
 	s3c_pm_restore_core();
 	s3c_pm_restore_uarts();
-	samsung_pm_restore_gpios();
-	s3c_pm_restored_gpios();
+
+	if (!of_have_populated_dt()) {
+		samsung_pm_restore_gpios();
+		s3c_pm_restored_gpios();
+	}
 
 	s3c_pm_debug_init();