Merge tag 'ti-k3-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt

TI K3 device tree updates for v6.10

Generic Cleanups/Fixes:
- fixup of generated dtb imx219 overlay file names
- Remove UART baud rate selection in device tree.
- Use exact ranges for FSS.

SoC specific Fixes/Features:

AM625:
- Add USB PHY2 region and usb phy control registers

AM62A
- Add USB PHY2 region and usb phy control registers, Disable USB LPM.
- Add wave-512 video encoder/decoder support
- Enable UHS mode for SD

AM62P:
- Disable ethernet by default
- Add USB support

AM654
- Serdes fixups
- SDHCI fixups.

AM67/j722s:
- Disable ethernet by default
- Add USB support

AM68/J721s2:
- Add main ESM range
- Add support for SDR104

AM69/J784S4:
- Add main ESM range
- Enable support for UHS mode

Board specific fixes/Features:

AM625:
- BeaglePlay: Fixes for wlan mmc-pwrseq and ethernet phy reset
- phyboard-lyra: Add Audio codec, USB-C, increase CAN bit rate and enable
ability to apply overlays
- verdin: GPIO pinctrl fixups, Switch SD carddetect to GPIO, fixup memory
to 2GB, and audio clock, PCIe reset GPIO hog, sleep-moci
- lp-sk: Drop power button
- sk: minor white space cleanup.

AM64
- phyboard-electra: Increase CAN bit rate, enable overlay to enable GPIO fan

AM65:
- iot2050: Add icssg-prueth for PG1

AM67/j722s:
- evm: Enable UHS support for SD card and eMMC support.

AM69/J784s4:
- evm/sk: Fix uart pins and pinctrl macro usage.

* tag 'ti-k3-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (48 commits)
arm64: dts: ti: Fix csi2-dual-imx219 dtb names
arm64: dts: ti: k3-am625-beagleplay: Fix Ethernet PHY RESET GPIOs
arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add USB-C
arm64: dts: ti: k3-j784s4: Add main esm address range
arm64: dts: ti: k3-j721s2: Add main esm address range
arm64: dts: ti: k3-am62-verdin-dahlia: support sleep-moci
arm64: dts: ti: k3-am62-verdin: replace sleep-moci hog with regulator
arm64: dts: ti: k3-j722s-evm: Enable UHS support for MMCSD
arm64: dts: ti: k3-j784s4-main: Enable support for UHS mode
arm64: dts: ti: k3-j721s2-main: Enable support for SDR104 speed mode
arm64: dts: ti: k3-am62a: Enable UHS mode support for SD cards
arm64: dts: ti: k3-am65-main: Remove unused properties in sdhci nodes
arm64: dts: ti: k3-am65-main: Fix sdhci node properties
arm64: dts: ti: Enable overlays for the am625-phyboard-lyra
arm64: dts: ti: am64-phyboard-electra: Add overlay to enable a GPIO fan
arm64: dts: ti: k3-am62a-main: Add Wave5 Video Encoder/Decoder Node
arm64: dts: ti: k3-am69-sk: Fix UART pin type and macro type
arm64: dts: ti: k3-j784s4-evm: Fix UART pin type and macro type
arm64: dts: ti: k3-am62a: Disable USB LPM
arm64: dts: ti: k3-am62p: add the USB sub-system
...

Link: https://lore.kernel.org/r/20240501124319.ake5j2oc5pbnn5nb@contour
Signed-off-by: Arnd Bergmann <[e-mail]>

arch/arm64/boot/dts/ti/Makefile

···
 dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-pcie.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-usb3.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-gpio-fan.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am64-tqma64xxl-mbax4xxl-sdcard.dtbo
···
 	k3-am62x-sk-csi2-tevi-ov5640.dtbo
 k3-am642-evm-icssg1-dualemac-dtbs := \
 	k3-am642-evm.dtb k3-am642-evm-icssg1-dualemac.dtbo
+k3-am642-phyboard-electra-gpio-fan-dtbs := \
+	k3-am642-phyboard-electra-rdk.dtb k3-am642-phyboard-electra-gpio-fan.dtbo
 k3-am642-tqma64xxl-mbax4xxl-sdcard-dtbs := \
 	k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-sdcard.dtbo
 k3-am642-tqma64xxl-mbax4xxl-wlan-dtbs := \
···
 	k3-am642-evm-icssg1-dualemac.dtb \
 	k3-am642-tqma64xxl-mbax4xxl-sdcard.dtb \
 	k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \
-	k3-am68-sk-base-board-csi2-dual-imx219-dtbs \
-	k3-am69-sk-csi2-dual-imx219-dtbs \
+	k3-am68-sk-base-board-csi2-dual-imx219.dtb \
+	k3-am69-sk-csi2-dual-imx219.dtb \
 	k3-j721e-evm-pcie0-ep.dtb \
-	k3-j721e-sk-csi2-dual-imx219-dtbs \
+	k3-j721e-sk-csi2-dual-imx219.dtb \
 	k3-j721s2-evm-pcie1-ep.dtb
 
 # Enable support for device-tree overlays
 DTC_FLAGS_k3-am625-beagleplay += -@
+DTC_FLAGS_k3-am625-phyboard-lyra-rdk += -@
 DTC_FLAGS_k3-am625-sk += -@
 DTC_FLAGS_k3-am62-lp-sk += -@
 DTC_FLAGS_k3-am62a7-sk += -@
 DTC_FLAGS_k3-am62p5-sk += -@
 DTC_FLAGS_k3-am642-evm += -@
+DTC_FLAGS_k3-am642-phyboard-electra-rdk += -@
 DTC_FLAGS_k3-am642-tqma64xxl-mbax4xxl += -@
 DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
 DTC_FLAGS_k3-am68-sk-base-board += -@

arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts

···
 
 		interrupt-parent = <&gic500>;
 		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
-		ti,power-button;
 
 		regulators {
 			buck1_reg: buck1 {

arch/arm64/boot/dts/ti/k3-am62-main.dtsi

···
 
 	usbss0: dwc3-usb@f900000 {
 		compatible = "ti,am62-usb";
-		reg = <0x00 0x0f900000 0x00 0x800>;
+		reg = <0x00 0x0f900000 0x00 0x800>,
+		      <0x00 0x0f908000 0x00 0x400>;
 		clocks = <&k3_clks 161 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
···
 
 	usbss1: dwc3-usb@f910000 {
 		compatible = "ti,am62-usb";
-		reg = <0x00 0x0f910000 0x00 0x800>;
+		reg = <0x00 0x0f910000 0x00 0x800>,
+		      <0x00 0x0f918000 0x00 0x400>;
 		clocks = <&k3_clks 162 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;

arch/arm64/boot/dts/ti/k3-am62-verdin-dahlia.dtsi

···
 		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&codec_dai>;
 		simple-audio-card,name = "verdin-wm8904";
+		simple-audio-card,mclk-fs = <256>;
 		simple-audio-card,routing =
 			"Headphone Jack", "HPOUTL",
 			"Headphone Jack", "HPOUTR",
···
 			"Line", "Line In Jack";
 
 		codec_dai: simple-audio-card,codec {
-			clocks = <&audio_refclk1>;
 			sound-dai = <&wm8904_1a>;
 		};
 
 		simple-audio-card,cpu {
 			sound-dai = <&mcasp0>;
 		};
+	};
+
+	reg_usb_hub: regulator-usb-hub {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpio = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		regulator-name = "HUB_PWR_EN";
 	};
 };
 
···
 	pinctrl-0 = <&pinctrl_gpio_1>,
 		    <&pinctrl_gpio_2>,
 		    <&pinctrl_gpio_3>,
-		    <&pinctrl_gpio_4>;
+		    <&pinctrl_gpio_4>,
+		    <&pinctrl_pcie_1_reset>;
 };
 
 /* Verdin I2C_3_HDMI */
···
 	status = "okay";
 };
 
+/* Do not force CTRL_SLEEP_MOCI# always enabled */
+&reg_force_sleep_moci {
+	status = "disabled";
+};
+
 /* Verdin SD_1 */
 &sdhci1 {
 	status = "okay";
···
 };
 
 &usb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	usb-hub@1 {
+		compatible = "usb424,2744";
+		reg = <1>;
+		vdd-supply = <&reg_usb_hub>;
+	};
 };
 
 /* Verdin CTRL_WAKE1_MICO# */
 &verdin_gpio_keys {
+	status = "okay";
+};
+
+/* Verdin PCIE_1_RESET# */
+&verdin_pcie_1_reset_hog {
 	status = "okay";
 };
 

arch/arm64/boot/dts/ti/k3-am62-verdin-dev.dtsi

···
 	pinctrl-0 = <&pinctrl_gpio_1>,
 		    <&pinctrl_gpio_2>,
 		    <&pinctrl_gpio_3>,
-		    <&pinctrl_gpio_4>;
+		    <&pinctrl_gpio_4>,
+		    <&pinctrl_pcie_1_reset>;
 };
 
 /* Verdin I2C_3_HDMI */
···
 
 /* Verdin CTRL_WAKE1_MICO# */
 &verdin_gpio_keys {
+	status = "okay";
+};
+
+/* Verdin PCIE_1_RESET# */
+&verdin_pcie_1_reset_hog {
 	status = "okay";
 };
 

arch/arm64/boot/dts/ti/k3-am62-verdin-mallow.dtsi

···
 &main_gpio0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>,
-		    <&pinctrl_gpio_1>,
-		    <&pinctrl_gpio_2>,
-		    <&pinctrl_gpio_3>,
-		    <&pinctrl_gpio_4>;
+		    <&pinctrl_gpio_5>,
+		    <&pinctrl_gpio_6>,
+		    <&pinctrl_gpio_7>,
+		    <&pinctrl_gpio_8>;
 };
 
 /* Verdin I2C_1 */
···
 	status = "okay";
 };
 
+&mcu_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_1>,
+		    <&pinctrl_gpio_2>,
+		    <&pinctrl_gpio_3>,
+		    <&pinctrl_gpio_4>,
+		    <&pinctrl_pcie_1_reset>;
+};
+
 /* Verdin I2C_3_HDMI */
 &mcu_i2c0 {
 	status = "okay";
···
 
 /* Verdin CTRL_WAKE1_MICO# */
 &verdin_gpio_keys {
+	status = "okay";
+};
+
+/* Verdin PCIE_1_RESET# */
+&verdin_pcie_1_reset_hog {
 	status = "okay";
 };
 

arch/arm64/boot/dts/ti/k3-am62-verdin-yavia.dtsi

···
 	pinctrl-0 = <&pinctrl_gpio_1>,
 		    <&pinctrl_gpio_2>,
 		    <&pinctrl_gpio_3>,
-		    <&pinctrl_gpio_4>;
+		    <&pinctrl_gpio_4>,
+		    <&pinctrl_pcie_1_reset>;
 };
 
 /* Verdin I2C_3_HDMI */
···
 
 /* Verdin CTRL_WAKE1_MICO# */
 &verdin_gpio_keys {
+	status = "okay";
+};
+
+/* Verdin PCIE_1_RESET# */
+&verdin_pcie_1_reset_hog {
 	status = "okay";
 };
 

arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi

···
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0x00000000 0x80000000 0x00000000 0x40000000>; /* 1G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>; /* 2G RAM */
 	};
 
 	opp-table {
···
 		regulator-min-microvolt = <1800000>;
 		regulator-name = "On-module +V1.8_ETH";
 		vin-supply = <&reg_1v8>;
+	};
+
+	/*
+	 * By default we enable CTRL_SLEEP_MOCI#, this is required to have
+	 * peripherals on the carrier board powered.
+	 * If more granularity or power saving is required this can be disabled
+	 * in the carrier board device tree files.
+	 */
+	reg_force_sleep_moci: regulator-force-sleep-moci {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpio = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "CTRL_SLEEP_MOCI#";
 	};
 
 	/* Verdin SD_1 Power Supply */
···
 		>;
 	};
 
+	/* Verdin SD_1_CD# as GPIO */
+	pinctrl_sd1_cd_gpio: main-gpio1-48-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 7) /* (D17) MMC1_SDCD.GPIO1_48 */ /* SODIMM 84 */
+		>;
+	};
+
 	/* Verdin DSI_1_INT# (pulled-up as active-low) */
 	pinctrl_dsi1_int: main-gpio1-49-default-pins {
 		pinctrl-single,pins = <
···
 			AM62X_IOPAD(0x22c, PIN_INPUT,        0) /* (B21) MMC1_DAT1 */ /* SODIMM 82 */
 			AM62X_IOPAD(0x228, PIN_INPUT,        0) /* (C21) MMC1_DAT2 */ /* SODIMM 70 */
 			AM62X_IOPAD(0x224, PIN_INPUT,        0) /* (D22) MMC1_DAT3 */ /* SODIMM 72 */
-			AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 0) /* (D17) MMC1_SDCD */ /* SODIMM 84 */
 		>;
 	};
 
···
 		"",
 		"",
 		"";
-
-	verdin_ctrl_sleep_moci: ctrl-sleep-moci-hog {
-		gpio-hog;
-		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
-		gpios = <31 GPIO_ACTIVE_HIGH>;
-		line-name = "CTRL_SLEEP_MOCI#";
-		output-high;
-	};
 };
 
 &main_gpio1 {
···
 		"",
 		"",
 		"";
+
+	verdin_pcie_1_reset_hog: pcie-1-reset-hog {
+		gpio-hog;
+		/* Verdin PCIE_1_RESET# (SODIMM 244) */
+		gpios = <0 GPIO_ACTIVE_LOW>;
+		line-name = "PCIE_1_RESET#";
+		output-low;
+		status = "disabled";
+	};
 };
 
 /* Verdin CAN_2 */
···
 /* Verdin SD_1 */
 &sdhci1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sdhci1>;
+	pinctrl-0 = <&pinctrl_sdhci1>, <&pinctrl_sd1_cd_gpio>;
+	cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	vmmc-supply = <&reg_sdhc1_vmmc>;
 	vqmmc-supply = <&reg_sdhc1_vqmmc>;
+	ti,fails-without-test-cd;
 	status = "disabled";
 };
 

arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi

···
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	target-module@2b300050 {

arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts

···
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_pins_default>;
+		/* Internal power on time(Figure 8-3) * 2 */
+		post-power-on-delay-ms = <10>;
+		/* Re-enable time(Figure 8-2) + 20uS */
+		power-off-delay-us = <80>;
+		reset-gpios = <&main_gpio0 38 GPIO_ACTIVE_LOW>;
+	};
+
 	vsys_5v0: regulator-1 {
 		bootph-all;
 		compatible = "regulator-fixed";
···
 		vin-supply = <&vsys_5v0>;
 		regulator-always-on;
 		regulator-boot-on;
-	};
-
-	wlan_en: regulator-3 {
-		/* OUTPUT of SN74AVC2T244DQMR */
-		compatible = "regulator-fixed";
-		regulator-name = "wlan_en";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		enable-active-high;
-		regulator-always-on;
-		vin-supply = <&vdd_3v3>;
-		gpio = <&main_gpio0 38 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_pins_default>;
 	};
 
 	vdd_3v3_sd: regulator-4 {
···
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
 			AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+			AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
+			AM62X_IOPAD(0x018c, PIN_INPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
 		>;
 	};
 
···
 			AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
 			AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
 			AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
-			AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
 			AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
 			AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
 		>;
···
 
 	cpsw3g_phy0: ethernet-phy@0 {
 		reg = <0>;
+		reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <50000>;
 	};
 
 	cpsw3g_phy1: ethernet-phy@1 {
···
 		"USR0", "USR1", "USR2", "USR3", "", "", "USR4",	/* 3-9 */
 		"EEPROM_WP",					/* 10 */
 		"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2",	/* 11-12 */
-		"CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "",	/* 13-17 */
+		"CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "",	/* 13-17 */
 		"USR_BUTTON", "", "", "", "", "", "", "", "",	/* 18-26 */
 		"", "", "", "", "", "", "", "", "", "HDMI_INT",	/* 27-36 */
 		"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
···
 };
 
 &sdhci2 {
-	vmmc-supply = <&wlan_en>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&wifi_pins_default>, <&wifi_32k_clk>;
 	non-removable;
 	ti,fails-without-test-cd;
 	cap-power-off-card;
 	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
 	assigned-clocks = <&k3_clks 157 158>;
 	assigned-clock-parents = <&k3_clks 157 160>;
 	#address-cells = <1>;

arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts

···
 	can_tc1: can-phy0 {
 		compatible = "ti,tcan1042";
 		#phy-cells = <0>;
-		max-bitrate = <5000000>;
+		max-bitrate = <8000000>;
 		standby-gpios = <&gpio_exp 1 GPIO_ACTIVE_HIGH>;
 	};
 
···
 		};
 	};
 
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "phyBOARD-Lyra";
+		simple-audio-card,widgets =
+			"Microphone",           "Mic Jack",
+			"Headphone",            "Headphone Jack",
+			"Speaker",              "External Speaker";
+		simple-audio-card,routing =
+			"MIC3R",                "Mic Jack",
+			"Mic Jack",             "Mic Bias",
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"External Speaker",     "SPOP",
+			"External Speaker",     "SPOM";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp2>;
+		};
+
+		sound_master: simple-audio-card,codec {
+				sound-dai = <&audio_codec>;
+				clocks = <&audio_refclk1>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
···
 		};
 	};
 
+	vcc_1v8: regulator-vcc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vcc_3v3_mmc: regulator-vcc-3v3-mmc {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC_3V3_MMC";
···
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vcc_3v3_sw: regulator-vcc-3v3-sw {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3_SW";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &main_pmx0 {
+	audio_ext_refclk1_pins_default: audio-ext-refclk1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0a0, PIN_OUTPUT, 1) /* (K25) GPMC0_WPn.AUDIO_EXT_REFCLK1 */
+		>;
+	};
+
 	gpio_keys_pins_default: gpio-keys-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x1d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
···
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x1dc, PIN_INPUT, 0) /* (E15) MCAN0_RX */
 			AM62X_IOPAD(0x1d8, PIN_OUTPUT, 0) /* (C15) MCAN0_TX */
+		>;
+	};
+
+	main_mcasp2_pins_default: main-mcasp2-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x070, PIN_INPUT, 3) /* (T24) GPMC0_AD13.MCASP2_ACLKX */
+			AM62X_IOPAD(0x06c, PIN_INPUT, 3) /* (T22) GPMC0_AD12.MCASP2_AFSX */
+			AM62X_IOPAD(0x064, PIN_OUTPUT, 3) /* (T25) GPMC0_AD10.MCASP2_AXR2 */
+			AM62X_IOPAD(0x068, PIN_INPUT, 3) /* (R21) GPMC0_AD11.MCASP2_AXR3 */
 		>;
 	};
 
···
 	clock-frequency = <100000>;
 	status = "okay";
 
+	audio_codec: audio-codec@18 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&audio_ext_refclk1_pins_default>;
+
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		ai3x-micbias-vg = <2>;
+
+		AVDD-supply = <&vcc_3v3_sw>;
+		IOVDD-supply = <&vcc_3v3_sw>;
+		DRVDD-supply = <&vcc_3v3_sw>;
+		DVDD-supply = <&vcc_1v8>;
+	};
+
 	gpio_exp: gpio-expander@21 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_exp_int_pins_default>;
···
 				  "GPIO2_LED2", "GPIO3_LVDS_GPIO",
 				  "GPIO4_BUT2", "GPIO5_LVDS_BKLT_EN",
 				  "GPIO6_ETH1_USER_RESET", "GPIO7_AUDIO_USER_RESET";
+	};
+
+	usb-pd@22 {
+		compatible = "ti,tps6598x";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			self-powered;
+			data-role = "dual";
+			power-role = "sink";
+			port {
+				usb_con_hs: endpoint {
+					remote-endpoint = <&typec_hs>;
+				};
+			};
+		};
 	};
 
 	sii9022: bridge-hdmi@39 {
···
 	status = "okay";
 };
 
+&mcasp2 {
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp2_pins_default>;
+
+	/* MCASP_IIS_MODE */
+	op-mode = <0>;
+	tdm-slots = <2>;
+
+	/* 0: INACTIVE, 1: TX, 2: RX */
+	serial-dir = <
+			0 0 1 2
+			0 0 0 0
+			0 0 0 0
+			0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+	status = "okay";
+};
+
 &sdhci1 {
 	vmmc-supply = <&vcc_3v3_mmc>;
 	vqmmc-supply = <&vddshv5_sdio>;
···
 };
 
 &usb0 {
-	dr_mode = "peripheral";
+	usb-role-switch;
+
+	port {
+		typec_hs: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
 };
 
 &usb1 {

arch/arm64/boot/dts/ti/k3-am62a-main.dtsi

···
 		ti,itap-del-sel-sd-hs = <0x0>;
 		ti,itap-del-sel-sdr12 = <0x0>;
 		ti,itap-del-sel-sdr25 = <0x0>;
-		no-1-8-v;
 		status = "disabled";
 	};
 
···
 		ti,itap-del-sel-sd-hs = <0x0>;
 		ti,itap-del-sel-sdr12 = <0x0>;
 		ti,itap-del-sel-sdr25 = <0x0>;
-		no-1-8-v;
 		status = "disabled";
 	};
 
 	usbss0: dwc3-usb@f900000 {
 		compatible = "ti,am62-usb";
-		reg = <0x00 0x0f900000 0x00 0x800>;
+		reg = <0x00 0x0f900000 0x00 0x800>,
+		      <0x00 0x0f908000 0x00 0x400>;
 		clocks = <&k3_clks 161 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
···
 			interrupt-names = "host", "peripheral";
 			maximum-speed = "high-speed";
 			dr_mode = "otg";
+			snps,usb2-gadget-lpm-disable;
+			snps,usb2-lpm-disable;
 		};
 	};
 
 	usbss1: dwc3-usb@f910000 {
 		compatible = "ti,am62-usb";
-		reg = <0x00 0x0f910000 0x00 0x800>;
+		reg = <0x00 0x0f910000 0x00 0x800>,
+		      <0x00 0x0f918000 0x00 0x400>;
 		clocks = <&k3_clks 162 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
···
 			interrupt-names = "host", "peripheral";
 			maximum-speed = "high-speed";
 			dr_mode = "otg";
+			snps,usb2-gadget-lpm-disable;
+			snps,usb2-lpm-disable;
 		};
 	};
 
···
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
+	};
+
+	vpu: video-codec@30210000 {
+		compatible = "ti,j721s2-wave521c", "cnm,wave521c";
+		reg = <0x00 0x30210000 0x00 0x10000>;
+		clocks = <&k3_clks 204 2>;
+		power-domains = <&k3_pds 204 TI_SCI_PD_EXCLUSIVE>;
 	};
 };

arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi

···
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	wkup_uart0: serial@2b300000 {

arch/arm64/boot/dts/ti/k3-am62a7-sk.dts

···
 		regulator-boot-on;
 	};
 
+	vddshv_sdio: regulator-5 {
+		compatible = "regulator-gpio";
+		regulator-name = "vddshv_sdio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vddshv_sdio_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&ldo1>;
+		gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
···
 	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
 		pinctrl-single,pins = <
 			AM62AX_IOPAD(0x01d4, PIN_INPUT, 7) /* (C15) UART0_RTSn.GPIO1_23 */
+		>;
+	};
+
+	vddshv_sdio_pins_default: vddshv-sdio-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x07c, PIN_OUTPUT, 7) /* (M19) GPMC0_CLK.GPIO0_31 */
 		>;
 	};
 };
···
 	/* SD/MMC */
 	status = "okay";
 	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vddshv_sdio>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	disable-wp;

arch/arm64/boot/dts/ti/k3-am62p-main.dtsi

···
 		status = "disabled";
 	};
 
+	usbss0: usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>,
+		      <0x00 0x0f908000 0x00 0x400>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+			<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+			snps,usb2-gadget-lpm-disable;
+			snps,usb2-lpm-disable;
+		};
+	};
+
+	usbss1: usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>,
+		      <0x00 0x0f918000 0x00 0x400>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+			<GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+			snps,usb2-gadget-lpm-disable;
+			snps,usb2-lpm-disable;
+		};
+	};
+
 	fss: bus@fc00000 {
 		compatible = "simple-bus";
 		reg = <0x00 0x0fc00000 0x00 0x70000>;
···
 		assigned-clock-parents = <&k3_clks 13 11>;
 		clock-names = "fck";
 		power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
 
 		dmas = <&main_pktdma 0xc600 15>,
 		       <&main_pktdma 0xc601 15>,
···
 				label = "port1";
 				phys = <&phy_gmii_sel 1>;
 				mac-address = [00 00 00 00 00 00];
+				status = "disabled";
 			};
 
 			cpsw_port2: port@2 {
···
 				label = "port2";
 				phys = <&phy_gmii_sel 2>;
 				mac-address = [00 00 00 00 00 00];
+				status = "disabled";
 			};
 		};
 

arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi

···
 			reg = <0x14 0x4>;
 			bootph-all;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	wkup_uart0: serial@2b300000 {

arch/arm64/boot/dts/ti/k3-am62p5-sk.dts

···
 		spi0 = &ospi0;
 		ethernet0 = &cpsw_port1;
 		ethernet1 = &cpsw_port2;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
···
 		bootph-all;
 	};
 
+	main_usb1_pins_default: main-usb1-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
+		>;
+	};
+
 	main_wlirq_pins_default: main-wlirq-default-pins {
 		pinctrl-single,pins = <
 			AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
···
 		pinctrl-single,pins = <
 			AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
 		>;
+	};
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	typec_pd0: usb-power-controller@3f {
+		compatible = "ti,tps6598x";
+		reg = <0x3f>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			self-powered;
+			data-role = "dual";
+			power-role = "sink";
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					usb_con_hs: endpoint {
+						remote-endpoint = <&usb0_hs_ep>;
+					};
+				};
+			};
+		};
 	};
 };
 
···
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_rgmii1_pins_default>,
 		    <&main_rgmii2_pins_default>;
+	status = "okay";
 };
 
 &cpsw_port1 {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy0>;
+	status = "okay";
 };
 
 &cpsw_port2 {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy1>;
+	status = "okay";
 };
 
 &cpsw3g_mdio {
···
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		ti,min-output-impedance;
 	};
+};
+
+&usbss0 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usbss1 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	usb-role-switch;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		usb0_hs_ep: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
 };
 
 &mcasp1 {
···
 	pinctrl-0 = <&ospi0_pins_default>;
 	bootph-all;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;

arch/arm64/boot/dts/ti/k3-am642-evm.dts

···
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
-	current-speed = <115200>;
 };
 
 /* main_uart1 is reserved for firmware usage */

arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-gpio-fan.dtso

···
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Copyright (C) 2024 PHYTEC America LLC
+ * Author: Nathan Morrisson <[e-mail]>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/thermal/thermal.h>
+#include "k3-pinctrl.h"
+
+&{/} {
+	fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpio-fan,speed-map = <0 0 8600 1>;
+		gpios = <&main_gpio0 28 GPIO_ACTIVE_LOW>;
+		#cooling-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_fan_pins_default>;
+	};
+};
+
+&main_pmx0 {
+	gpio_fan_pins_default: gpio-fan-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x070, PIN_OUTPUT, 7) /* (V18) GPMC0_AD13.GPIO0_28 */
+		>;
+	};
+};
+
+&thermal_zones {
+	main0_thermal: main0-thermal {
+		trips {
+			main0_thermal_trip0: main0-thermal-trip {
+				temperature = <65000>;  /* millicelsius */
+				hysteresis = <2000>;    /* millicelsius */
+				type = "active";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&main0_thermal_trip0>;
+				cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};

arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts

···
 		pinctrl-names = "default";
 		pinctrl-0 = <&can_tc1_pins_default>;
 		#phy-cells = <0>;
-		max-bitrate = <5000000>;
+		max-bitrate = <8000000>;
 		standby-gpios = <&main_gpio0 32 GPIO_ACTIVE_HIGH>;
 	};
 
···
 		pinctrl-names = "default";
 		pinctrl-0 = <&can_tc2_pins_default>;
 		#phy-cells = <0>;
-		max-bitrate = <5000000>;
+		max-bitrate = <8000000>;
 		standby-gpios = <&main_gpio0 35 GPIO_ACTIVE_HIGH>;
 	};
 
···
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
-	current-speed = <115200>;
 };
 
 &main_uart1 {
···
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart1_pins_default>;
 	uart-has-rtscts;
-	current-speed = <115200>;
 };
 
 &sdhci1 {

arch/arm64/boot/dts/ti/k3-am642-sk.dts

···
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
-	current-speed = <115200>;
 };
 
 &main_uart1 {

arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi

···
 };
 
 &icssg0_eth {
-	status = "disabled";
-};
+	compatible = "ti,am654-sr1-icssg-prueth";
 
-&icssg0_mdio {
-	status = "disabled";
+	ti,prus = <&pru0_0>, <&rtu0_0>, <&pru0_1>, <&rtu0_1>;
+	firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf",
+			"ti-pruss/am65x-rtu0-prueth-fw.elf",
+			"ti-pruss/am65x-pru1-prueth-fw.elf",
+			"ti-pruss/am65x-rtu1-prueth-fw.elf";
+
+	ti,pruss-gp-mux-sel = <2>,      /* MII mode */
+			      <2>,
+			      <2>,      /* MII mode */
+			      <2>;
+
+	dmas = <&main_udmap 0xc100>, /* egress slice 0 */
+	       <&main_udmap 0xc101>, /* egress slice 0 */
+	       <&main_udmap 0xc102>, /* egress slice 0 */
+	       <&main_udmap 0xc103>, /* egress slice 0 */
+	       <&main_udmap 0xc104>, /* egress slice 1 */
+	       <&main_udmap 0xc105>, /* egress slice 1 */
+	       <&main_udmap 0xc106>, /* egress slice 1 */
+	       <&main_udmap 0xc107>, /* egress slice 1 */
+	       <&main_udmap 0x4100>, /* ingress slice 0 */
+	       <&main_udmap 0x4101>, /* ingress slice 1 */
+	       <&main_udmap 0x4102>, /* mgmnt rsp slice 0 */
+	       <&main_udmap 0x4103>; /* mgmnt rsp slice 1 */
+	dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
+		    "tx1-0", "tx1-1", "tx1-2", "tx1-3",
+		    "rx0", "rx1",
+		    "rxmgm0", "rxmgm1";
 };

arch/arm64/boot/dts/ti/k3-am65-main.dtsi

···
 		assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>;
 		ti,serdes-clk = <&serdes0_clk>;
 		#clock-cells = <1>;
-		mux-controls = <&serdes_mux 0>;
+		mux-controls = <&serdes0_mux 0>;
 	};
 
 	serdes1: serdes@910000 {
···
 		assigned-clock-parents = <&k3_clks 154 9>, <&k3_clks 154 5>;
 		ti,serdes-clk = <&serdes1_clk>;
 		#clock-cells = <1>;
-		mux-controls = <&serdes_mux 1>;
+		mux-controls = <&serdes1_mux 0>;
 	};
 
 	main_uart0: serial@2800000 {
···
 		reg = <0x00 0x02800000 0x00 0x100>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
 		status = "disabled";
 	};
···
 		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 		mmc-ddr-1_8v;
 		mmc-hs200-1_8v;
+		ti,clkbuf-sel = <0x7>;
+		ti,trm-icp = <0x8>;
 		ti,otap-del-sel-legacy = <0x0>;
 		ti,otap-del-sel-mmc-hs = <0x0>;
-		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0x0>;
-		ti,otap-del-sel-sdr25 = <0x0>;
-		ti,otap-del-sel-sdr50 = <0x8>;
-		ti,otap-del-sel-sdr104 = <0x7>;
-		ti,otap-del-sel-ddr50 = <0x5>;
 		ti,otap-del-sel-ddr52 = <0x5>;
 		ti,otap-del-sel-hs200 = <0x5>;
-		ti,otap-del-sel-hs400 = <0x0>;
-		ti,trm-icp = <0x8>;
+		ti,itap-del-sel-ddr52 = <0x0>;
 		dma-coherent;
 		status = "disabled";
 	};
···
 		clocks = <&k3_clks 48 0>, <&k3_clks 48 1>;
 		clock-names = "clk_ahb", "clk_xin";
 		interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+		ti,clkbuf-sel = <0x7>;
+		ti,trm-icp = <0x8>;
 		ti,otap-del-sel-legacy = <0x0>;
-		ti,otap-del-sel-mmc-hs = <0x0>;
 		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0x0>;
-		ti,otap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
 		ti,otap-del-sel-sdr50 = <0x8>;
 		ti,otap-del-sel-sdr104 = <0x7>;
 		ti,otap-del-sel-ddr50 = <0x4>;
-		ti,otap-del-sel-ddr52 = <0x4>;
-		ti,otap-del-sel-hs200 = <0x7>;
-		ti,clkbuf-sel = <0x7>;
-		ti,trm-icp = <0x8>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-sd-hs = <0x1>;
+		ti,itap-del-sel-sdr12 = <0xa>;
+		ti,itap-del-sel-sdr25 = <0x1>;
 		dma-coherent;
 		status = "disabled";
 	};
···
 		ranges = <0x0 0x0 0x00100000 0x1c000>;
 
 		serdes0_clk: clock@4080 {
-			compatible = "syscon";
-			reg = <0x00004080 0x4>;
+			compatible = "ti,am654-serdes-ctrl", "syscon";
+			reg = <0x4080 0x4>;
+
+			serdes0_mux: mux-controller {
+				compatible = "mmio-mux";
+				#mux-control-cells = <1>;
+				mux-reg-masks = <0x0 0x3>; /* lane select */
+			};
 		};
 
 		serdes1_clk: clock@4090 {
-			compatible = "syscon";
-			reg = <0x00004090 0x4>;
-		};
+			compatible = "ti,am654-serdes-ctrl", "syscon";
+			reg = <0x4090 0x4>;
 
-		serdes_mux: mux-controller {
-			compatible = "mmio-mux";
-			#mux-control-cells = <1>;
-			mux-reg-masks = <0x4080 0x3>, /* SERDES0 lane select */
-					<0x4090 0x3>; /* SERDES1 lane select */
+			serdes1_mux: mux-controller {
+				compatible = "mmio-mux";
+				#mux-control-cells = <1>;
+				mux-reg-masks = <0x0 0x3>; /* lane select */
+			};
 		};
 
 		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41e0 {

arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi

···
 		reg = <0x00 0x40a00000 0x00 0x100>;
 		interrupts = <GIC_SPI 565 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <96000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		status = "disabled";
 	};
···
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
-		ranges;
+		ranges = <0x0 0x47000000 0x0 0x47000000 0x0 0x100>, /* FSS Control */
+			 <0x0 0x47040000 0x0 0x47040000 0x0 0x100>, /* OSPI0 Control */
+			 <0x0 0x47050000 0x0 0x47050000 0x0 0x100>, /* OSPI1 Control */
+			 <0x5 0x00000000 0x5 0x00000000 0x1 0x0000000>, /* OSPI0 Memory */
+			 <0x7 0x00000000 0x7 0x00000000 0x1 0x0000000>; /* OSPI1 Memory */
 
 		ospi0: spi@47040000 {
 			compatible = "ti,am654-ospi", "cdns,qspi-nor";

arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi

···
 		reg = <0x42300000 0x100>;
 		interrupts = <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 150 TI_SCI_PD_EXCLUSIVE>;
 		status = "disabled";
 	};

arch/arm64/boot/dts/ti/k3-am69-sk.dts

···
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
-			J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */
-			J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */
-			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
-			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
+			J784S4_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_UART0_CTSn */
+			J784S4_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (L36) WKUP_UART0_RTSn */
+			J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
+			J784S4_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (K34) WKUP_UART0_TXD */
 		>;
 	};
 
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
-			J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
-			J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+			J784S4_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+			J784S4_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
 		>;
 	};
 

arch/arm64/boot/dts/ti/k3-j7200-main.dtsi

···
 		reg = <0x00 0x02800000 0x00 0x100>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 146 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02810000 0x00 0x100>;
 		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 278 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 278 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02820000 0x00 0x100>;
 		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 279 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 279 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02830000 0x00 0x100>;
 		interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 280 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 280 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02840000 0x00 0x100>;
 		interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 281 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 281 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02850000 0x00 0x100>;
 		interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 282 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 282 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02860000 0x00 0x100>;
 		interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 283 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 283 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02870000 0x00 0x100>;
 		interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 284 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 284 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02880000 0x00 0x100>;
 		interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 285 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 285 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02890000 0x00 0x100>;
 		interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 286 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 286 2>;
 		clock-names = "fclk";

arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi

···
 		reg = <0x00 0x42300000 0x00 0x100>;
 		interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 287 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 287 2>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x40a00000 0x00 0x100>;
 		interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <96000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 2>;
 		clock-names = "fclk";
···
 
 	fss: bus@47000000 {
 		compatible = "simple-bus";
-		reg = <0x00 0x47000000 0x00 0x100>;
 		#address-cells = <2>;
 		#size-cells = <2>;
-		ranges;
+		ranges = <0x0 0x47000000 0x0 0x47000000 0x0 0x100>, /* FSS Control */
+			 <0x0 0x47034000 0x0 0x47040000 0x0 0x100>, /* HBMC Control */
+			 <0x0 0x47040000 0x0 0x47040000 0x0 0x100>, /* OSPI0 Control */
+			 <0x5 0x00000000 0x5 0x00000000 0x1 0x0000000>; /* HBMC/OSPI0 Memory */
 
 		hbmc_mux: mux-controller@47000004 {
 			compatible = "reg-mux";

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi

···
 		reg = <0x00 0x02800000 0x00 0x100>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 146 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02810000 0x00 0x100>;
 		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 278 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 278 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02820000 0x00 0x100>;
 		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 279 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 279 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02830000 0x00 0x100>;
 		interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 280 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 280 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02840000 0x00 0x100>;
 		interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 281 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 281 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02850000 0x00 0x100>;
 		interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 282 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 282 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02860000 0x00 0x100>;
 		interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 283 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 283 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02870000 0x00 0x100>;
 		interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 284 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 284 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02880000 0x00 0x100>;
 		interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 285 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 285 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x02890000 0x00 0x100>;
 		interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 286 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 286 0>;
 		clock-names = "fclk";

arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi

···
 		reg = <0x00 0x42300000 0x00 0x100>;
 		interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <48000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 287 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 287 0>;
 		clock-names = "fclk";
···
 		reg = <0x00 0x40a00000 0x00 0x100>;
 		interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <96000000>;
-		current-speed = <115200>;
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 0>;
 		clock-names = "fclk";
···
 
 	fss: bus@47000000 {
 		compatible = "simple-bus";
-		reg = <0x0 0x47000000 0x0 0x100>;
 		#address-cells = <2>;
 		#size-cells = <2>;
-		ranges;
+		ranges = <0x0 0x47000000 0x0 0x47000000 0x0 0x100>, /* FSS Control */
+			 <0x0 0x47034000 0x0 0x47034000 0x0 0x100>, /* HBMC Control */
+			 <0x0 0x47040000 0x0 0x47040000 0x0 0x100>, /* OSPI0 Control */
+			 <0x0 0x47050000 0x0 0x47050000 0x0 0x100>, /* OSPI1 Control */
+			 <0x5 0x00000000 0x5 0x00000000 0x1 0x0000000>, /* HBMC/OSPI0 Memory */
+			 <0x7 0x00000000 0x7 0x00000000 0x1 0x0000000>; /* OSPI1 Memory */
 
 		hbmc_mux: mux-controller@47000004 {
 			compatible = "reg-mux";

arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi

···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x200>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 146 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02810000 0x00 0x200>;
 		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 350 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 350 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02820000 0x00 0x200>;
 		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 351 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 351 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02830000 0x00 0x200>;
 		interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 352 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 352 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02840000 0x00 0x200>;
 		interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 353 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 353 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02850000 0x00 0x200>;
 		interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 354 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 354 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02860000 0x00 0x200>;
 		interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 355 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 355 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02870000 0x00 0x200>;
 		interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 356 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 356 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02880000 0x00 0x200>;
 		interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 357 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 357 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02890000 0x00 0x200>;
 		interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 358 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 358 TI_SCI_PD_EXCLUSIVE>;
···
 		ti,clkbuf-sel = <0x7>;
 		ti,trm-icp = <0x8>;
 		dma-coherent;
-		/* Masking support for SDR104 capability */
-		sdhci-caps-mask = <0x00000003 0x00000000>;
 		status = "disabled";
 	};
 

arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi

···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x42300000 0x00 0x200>;
 		interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 359 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 359 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x40a00000 0x00 0x200>;
 		interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 149 3>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;

arch/arm64/boot/dts/ti/k3-j721s2.dtsi

···
 		#size-cells = <2>;
 		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
 			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
+			 <0x00 0x00700000 0x00 0x00700000 0x00 0x00001000>, /* ESM */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
 			 <0x00 0x0d800000 0x00 0x0d800000 0x00 0x00800000>, /* PCIe Core*/
 			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */

arch/arm64/boot/dts/ti/k3-j722s-evm.dts

···
 &cpsw_port1 {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy0>;
-};
-
-&cpsw_port2 {
-	status = "disabled";
+	status = "okay";
 };
 
 &main_gpio1 {
···
 
 };
 
+&sdhci0 {
+	disable-wp;
+	bootph-all;
+	ti,driver-strength-ohm = <50>;
+	status = "okay";
+};
+
 &sdhci1 {
 	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;
···
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
-	no-1-8-v;
 	status = "okay";
 	bootph-all;
 };

arch/arm64/boot/dts/ti/k3-j784s4-evm.dts

···
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
-			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
-			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
+			J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
+			J784S4_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (K34) WKUP_UART0_TXD */
 		>;
 	};
 
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
-			J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
-			J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+			J784S4_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+			J784S4_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
 		>;
 	};
 

arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi

···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x200>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 146 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02810000 0x00 0x200>;
 		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 388 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 388 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02820000 0x00 0x200>;
 		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 389 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 389 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02830000 0x00 0x200>;
 		interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 390 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 390 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02840000 0x00 0x200>;
 		interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 391 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 391 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02850000 0x00 0x200>;
 		interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 392 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 392 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02860000 0x00 0x200>;
 		interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 393 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 393 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02870000 0x00 0x200>;
 		interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 394 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 394 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02880000 0x00 0x200>;
 		interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 395 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 395 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02890000 0x00 0x200>;
 		interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 396 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 396 TI_SCI_PD_EXCLUSIVE>;
···
 		ti,clkbuf-sel = <0x7>;
 		ti,trm-icp = <0x8>;
 		dma-coherent;
-		sdhci-caps-mask = <0x00000003 0x00000000>;
-		no-1-8-v;
 		status = "disabled";
 	};
 

arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi

···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x42300000 0x00 0x200>;
 		interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 397 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 397 TI_SCI_PD_EXCLUSIVE>;
···
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x40a00000 0x00 0x200>;
 		interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
-		current-speed = <115200>;
 		clocks = <&k3_clks 149 0>;
 		clock-names = "fclk";
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
···
 
 	fss: bus@47000000 {
 		compatible = "simple-bus";
-		reg = <0x00 0x47000000 0x00 0x100>;
 		#address-cells = <2>;
 		#size-cells = <2>;
-		ranges;
+		ranges = <0x0 0x47000000 0x0 0x47000000 0x0 0x100>, /* FSS Control */
+			 <0x0 0x47040000 0x0 0x47040000 0x0 0x100>, /* OSPI0 Control */
+			 <0x0 0x47050000 0x0 0x47050000 0x0 0x100>, /* OSPI1 Control */
+			 <0x5 0x00000000 0x5 0x00000000 0x1 0x0000000>, /* OSPI0 Memory */
+			 <0x7 0x00000000 0x7 0x00000000 0x1 0x0000000>; /* OSPI1 Memory */
 
 		ospi0: spi@47040000 {
 			compatible = "ti,am654-ospi", "cdns,qspi-nor";

arch/arm64/boot/dts/ti/k3-j784s4.dtsi

···
 		#size-cells = <2>;
 		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
 			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
+			 <0x00 0x00700000 0x00 0x00700000 0x00 0x00001000>, /* ESM */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
 			 <0x00 0x04210000 0x00 0x04210000 0x00 0x00010000>, /* VPU0 */
 			 <0x00 0x04220000 0x00 0x04220000 0x00 0x00010000>, /* VPU1 */