nfc: pn533: add UART phy driver

This adds the UART phy interface for the pn533 driver.
The pn533 driver can be used through UART interface this way.
It is implemented as a serdev device.

Cc: Johan Hovold <[e-mail]>
Cc: Claudiu Beznea <[e-mail]>
Cc: David Miller <[e-mail]>
Signed-off-by: Lars Poeschel <[e-mail]>
Signed-off-by: David S. Miller <[e-mail]>

drivers/nfc/pn533/Kconfig

···
 
 	  If you choose to build a module, it'll be called pn533_i2c.
 	  Say N if unsure.
+
+config NFC_PN532_UART
+	tristate "NFC PN532 device support (UART)"
+	depends on SERIAL_DEV_BUS
+	select NFC_PN533
+	---help---
+	  This module adds support for the NXP pn532 UART interface.
+	  Select this if your platform is using the UART bus.
+
+	  If you choose to build a module, it'll be called pn532_uart.
+	  Say N if unsure.

drivers/nfc/pn533/Makefile

···
 #
 pn533_usb-objs  = usb.o
 pn533_i2c-objs  = i2c.o
+pn532_uart-objs  = uart.o
 
 obj-$(CONFIG_NFC_PN533)     += pn533.o
 obj-$(CONFIG_NFC_PN533_USB) += pn533_usb.o
 obj-$(CONFIG_NFC_PN533_I2C) += pn533_i2c.o
+obj-$(CONFIG_NFC_PN532_UART) += pn532_uart.o

drivers/nfc/pn533/pn533.h

···
 
 /* Preamble (1), SoPC (2), ACK Code (2), Postamble (1) */
 #define PN533_STD_FRAME_ACK_SIZE 6
+/*
+ * Preamble (1), SoPC (2), Packet Length (1), Packet Length Checksum (1),
+ * Specific Application Level Error Code (1) , Postamble (1)
+ */
+#define PN533_STD_ERROR_FRAME_SIZE 8
 #define PN533_STD_FRAME_CHECKSUM(f) (f->data[f->datalen])
 #define PN533_STD_FRAME_POSTAMBLE(f) (f->data[f->datalen + 1])
 /* Half start code (3), LEN (4) should be 0xffff for extended frame */
···
 #define PN533_CMD_MI_MASK 0x40
 #define PN533_CMD_RET_SUCCESS 0x00
 
+#define PN533_FRAME_DATALEN_ACK 0x00
+#define PN533_FRAME_DATALEN_ERROR 0x01
+#define PN533_FRAME_DATALEN_EXTENDED 0xFF
 
 enum  pn533_protocol_type {
 	PN533_PROTO_REQ_ACK_RESP = 0,

drivers/nfc/pn533/uart.c

···
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for NXP PN532 NFC Chip - UART transport layer
+ *
+ * Copyright (C) 2018 Lemonage Software GmbH
+ * Author: Lars Pöschel <[e-mail]>
+ * All rights reserved.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nfc.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/serdev.h>
+#include "pn533.h"
+
+#define PN532_UART_SKB_BUFF_LEN	(PN533_CMD_DATAEXCH_DATA_MAXLEN * 2)
+
+enum send_wakeup {
+	PN532_SEND_NO_WAKEUP = 0,
+	PN532_SEND_WAKEUP,
+	PN532_SEND_LAST_WAKEUP,
+};
+
+
+struct pn532_uart_phy {
+	struct serdev_device *serdev;
+	struct sk_buff *recv_skb;
+	struct pn533 *priv;
+	/*
+	 * send_wakeup variable is used to control if we need to send a wakeup
+	 * request to the pn532 chip prior to our actual command. There is a
+	 * little propability of a race condition. We decided to not mutex the
+	 * variable as the worst that could happen is, that we send a wakeup
+	 * to the chip that is already awake. This does not hurt. It is a
+	 * no-op to the chip.
+	 */
+	enum send_wakeup send_wakeup;
+	struct timer_list cmd_timeout;
+	struct sk_buff *cur_out_buf;
+};
+
+static int pn532_uart_send_frame(struct pn533 *dev,
+				struct sk_buff *out)
+{
+	/* wakeup sequence and dummy bytes for waiting time */
+	static const u8 wakeup[] = {
+		0x55, 0x55, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+		0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
+	struct pn532_uart_phy *pn532 = dev->phy;
+	int err;
+
+	print_hex_dump_debug("PN532_uart TX: ", DUMP_PREFIX_NONE, 16, 1,
+			     out->data, out->len, false);
+
+	pn532->cur_out_buf = out;
+	if (pn532->send_wakeup) {
+		err = serdev_device_write(pn532->serdev,
+				wakeup, sizeof(wakeup),
+				MAX_SCHEDULE_TIMEOUT);
+		if (err < 0)
+			return err;
+	}
+
+	if (pn532->send_wakeup == PN532_SEND_LAST_WAKEUP)
+		pn532->send_wakeup = PN532_SEND_NO_WAKEUP;
+
+	err = serdev_device_write(pn532->serdev, out->data, out->len,
+			MAX_SCHEDULE_TIMEOUT);
+	if (err < 0)
+		return err;
+
+	mod_timer(&pn532->cmd_timeout, HZ / 40 + jiffies);
+	return 0;
+}
+
+static int pn532_uart_send_ack(struct pn533 *dev, gfp_t flags)
+{
+	/* spec 7.1.1.3:  Preamble, SoPC (2), ACK Code (2), Postamble */
+	static const u8 ack[PN533_STD_FRAME_ACK_SIZE] = {
+			0x00, 0x00, 0xff, 0x00, 0xff, 0x00};
+	struct pn532_uart_phy *pn532 = dev->phy;
+	int err;
+
+	err = serdev_device_write(pn532->serdev, ack, sizeof(ack),
+			MAX_SCHEDULE_TIMEOUT);
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+
+static void pn532_uart_abort_cmd(struct pn533 *dev, gfp_t flags)
+{
+	/* An ack will cancel the last issued command */
+	pn532_uart_send_ack(dev, flags);
+	/* schedule cmd_complete_work to finish current command execution */
+	pn533_recv_frame(dev, NULL, -ENOENT);
+}
+
+static void pn532_dev_up(struct pn533 *dev)
+{
+	struct pn532_uart_phy *pn532 = dev->phy;
+
+	serdev_device_open(pn532->serdev);
+	pn532->send_wakeup = PN532_SEND_LAST_WAKEUP;
+}
+
+static void pn532_dev_down(struct pn533 *dev)
+{
+	struct pn532_uart_phy *pn532 = dev->phy;
+
+	serdev_device_close(pn532->serdev);
+	pn532->send_wakeup = PN532_SEND_WAKEUP;
+}
+
+static struct pn533_phy_ops uart_phy_ops = {
+	.send_frame = pn532_uart_send_frame,
+	.send_ack = pn532_uart_send_ack,
+	.abort_cmd = pn532_uart_abort_cmd,
+	.dev_up = pn532_dev_up,
+	.dev_down = pn532_dev_down,
+};
+
+static void pn532_cmd_timeout(struct timer_list *t)
+{
+	struct pn532_uart_phy *dev = from_timer(dev, t, cmd_timeout);
+
+	pn532_uart_send_frame(dev->priv, dev->cur_out_buf);
+}
+
+/*
+ * scans the buffer if it contains a pn532 frame. It is not checked if the
+ * frame is really valid. This is later done with pn533_rx_frame_is_valid.
+ * This is useful for malformed or errornous transmitted frames. Adjusts the
+ * bufferposition where the frame starts, since pn533_recv_frame expects a
+ * well formed frame.
+ */
+static int pn532_uart_rx_is_frame(struct sk_buff *skb)
+{
+	struct pn533_std_frame *std;
+	struct pn533_ext_frame *ext;
+	u16 frame_len;
+	int i;
+
+	for (i = 0; i + PN533_STD_FRAME_ACK_SIZE <= skb->len; i++) {
+		std = (struct pn533_std_frame *)&skb->data[i];
+		/* search start code */
+		if (std->start_frame != cpu_to_be16(PN533_STD_FRAME_SOF))
+			continue;
+
+		/* frame type */
+		switch (std->datalen) {
+		case PN533_FRAME_DATALEN_ACK:
+			if (std->datalen_checksum == 0xff) {
+				skb_pull(skb, i);
+				return 1;
+			}
+
+			break;
+		case PN533_FRAME_DATALEN_ERROR:
+			if ((std->datalen_checksum == 0xff) &&
+					(skb->len >=
+					 PN533_STD_ERROR_FRAME_SIZE)) {
+				skb_pull(skb, i);
+				return 1;
+			}
+
+			break;
+		case PN533_FRAME_DATALEN_EXTENDED:
+			ext = (struct pn533_ext_frame *)&skb->data[i];
+			frame_len = be16_to_cpu(ext->datalen);
+			if (skb->len >= frame_len +
+					sizeof(struct pn533_ext_frame) +
+					2 /* CKS + Postamble */) {
+				skb_pull(skb, i);
+				return 1;
+			}
+
+			break;
+		default: /* normal information frame */
+			frame_len = std->datalen;
+			if (skb->len >= frame_len +
+					sizeof(struct pn533_std_frame) +
+					2 /* CKS + Postamble */) {
+				skb_pull(skb, i);
+				return 1;
+			}
+
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int pn532_receive_buf(struct serdev_device *serdev,
+		const unsigned char *data, size_t count)
+{
+	struct pn532_uart_phy *dev = serdev_device_get_drvdata(serdev);
+	size_t i;
+
+	del_timer(&dev->cmd_timeout);
+	for (i = 0; i < count; i++) {
+		skb_put_u8(dev->recv_skb, *data++);
+		if (!pn532_uart_rx_is_frame(dev->recv_skb))
+			continue;
+
+		pn533_recv_frame(dev->priv, dev->recv_skb, 0);
+		dev->recv_skb = alloc_skb(PN532_UART_SKB_BUFF_LEN, GFP_KERNEL);
+		if (!dev->recv_skb)
+			return 0;
+	}
+
+	return i;
+}
+
+static struct serdev_device_ops pn532_serdev_ops = {
+	.receive_buf = pn532_receive_buf,
+	.write_wakeup = serdev_device_write_wakeup,
+};
+
+static const struct of_device_id pn532_uart_of_match[] = {
+	{ .compatible = "nxp,pn532", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, pn532_uart_of_match);
+
+static int pn532_uart_probe(struct serdev_device *serdev)
+{
+	struct pn532_uart_phy *pn532;
+	struct pn533 *priv;
+	int err;
+
+	err = -ENOMEM;
+	pn532 = kzalloc(sizeof(*pn532), GFP_KERNEL);
+	if (!pn532)
+		goto err_exit;
+
+	pn532->recv_skb = alloc_skb(PN532_UART_SKB_BUFF_LEN, GFP_KERNEL);
+	if (!pn532->recv_skb)
+		goto err_free;
+
+	pn532->serdev = serdev;
+	serdev_device_set_drvdata(serdev, pn532);
+	serdev_device_set_client_ops(serdev, &pn532_serdev_ops);
+	err = serdev_device_open(serdev);
+	if (err) {
+		dev_err(&serdev->dev, "Unable to open device\n");
+		goto err_skb;
+	}
+
+	err = serdev_device_set_baudrate(serdev, 115200);
+	if (err != 115200) {
+		err = -EINVAL;
+		goto err_serdev;
+	}
+
+	serdev_device_set_flow_control(serdev, false);
+	pn532->send_wakeup = PN532_SEND_WAKEUP;
+	timer_setup(&pn532->cmd_timeout, pn532_cmd_timeout, 0);
+	priv = pn53x_common_init(PN533_DEVICE_PN532,
+				     PN533_PROTO_REQ_ACK_RESP,
+				     pn532, &uart_phy_ops, NULL,
+				     &pn532->serdev->dev);
+	if (IS_ERR(priv)) {
+		err = PTR_ERR(priv);
+		goto err_serdev;
+	}
+
+	pn532->priv = priv;
+	err = pn533_finalize_setup(pn532->priv);
+	if (err)
+		goto err_clean;
+
+	serdev_device_close(serdev);
+	err = pn53x_register_nfc(priv, PN533_NO_TYPE_B_PROTOCOLS, &serdev->dev);
+	if (err) {
+		pn53x_common_clean(pn532->priv);
+		goto err_skb;
+	}
+
+	return err;
+
+err_clean:
+	pn53x_common_clean(pn532->priv);
+err_serdev:
+	serdev_device_close(serdev);
+err_skb:
+	kfree_skb(pn532->recv_skb);
+err_free:
+	kfree(pn532);
+err_exit:
+	return err;
+}
+
+static void pn532_uart_remove(struct serdev_device *serdev)
+{
+	struct pn532_uart_phy *pn532 = serdev_device_get_drvdata(serdev);
+
+	pn53x_unregister_nfc(pn532->priv);
+	serdev_device_close(serdev);
+	pn53x_common_clean(pn532->priv);
+	kfree_skb(pn532->recv_skb);
+	kfree(pn532);
+}
+
+static struct serdev_device_driver pn532_uart_driver = {
+	.probe = pn532_uart_probe,
+	.remove = pn532_uart_remove,
+	.driver = {
+		.name = "pn532_uart",
+		.of_match_table = of_match_ptr(pn532_uart_of_match),
+	},
+};
+
+module_serdev_device_driver(pn532_uart_driver);
+
+MODULE_AUTHOR("Lars Pöschel <[e-mail]>");
+MODULE_DESCRIPTION("PN532 UART driver");
+MODULE_LICENSE("GPL");