blackfin: cleanup board files

using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)

Signed-off-by: Steven Miao <[e-mail]>

arch/blackfin/mach-bf518/boards/ezbrd.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezbrd_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 
 static struct resource ezbrd_flash_resource = {
 	.start = 0x20000000,
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	.end   = 0x202fffff,
 #else
 	.end   = 0x203fffff,
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = {
 	P_MII0_ETxD0,
···
 
 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 	{
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 		.addr = 3,
 #else
 		.addr = 1,
···
 	.phydev_data = bfin_phydev_data,
 	.phy_mode = PHY_INTERFACE_MODE_MII,
 	.mac_peripherals = bfin_mac_peripherals,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	.phy_mask = 0xfff7, /* Only probe the port phy connect to the on chip MAC */
 #endif
 	.vlan1_mask = 1,
···
 	}
 };
 
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 static struct dsa_chip_data ksz8893m_switch_chip_data = {
 	.mii_bus = &bfin_mii_bus.dev,
 	.port_names = {
···
 #endif
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-#if defined(CONFIG_NET_DSA_KSZ8893M) \
-	|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	{
 		.modalias = "ksz8893m",
 		.max_speed_hz = 5000000,
···
 #endif
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
 	 && defined(CONFIG_SND_SOC_WM8731_SPI)
 	{
 		.modalias	= "wm8731",
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 
 /* SPI controller data */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 6,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_RSI,
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	&ksz8893m_switch_device,
 #endif
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 	&bfin_spi1_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bf51x_sdh_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezbrd_flash_device,
 #endif
 };
···
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	/* setup BF518-EZBRD GPIO pin PG11 to AMS2, PG15 to AMS3. */
 	peripheral_request(P_AMS2, "ParaFlash");
-#if !defined(CONFIG_SPI_BFIN5XX) && !defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if !IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	peripheral_request(P_AMS3, "ParaFlash");
 #endif
 	return 0;

arch/blackfin/mach-bf518/boards/tcm-bf518.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition tcm_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
 	 && defined(CONFIG_SND_SOC_WM8731_SPI)
 	{
 		.modalias	= "wm8731",
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 
 /* SPI controller data */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 6,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
···
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_RSI,
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 	&bfin_spi1_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bf51x_sdh_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&tcm_flash_device,
 #endif
 };

arch/blackfin/mach-bf527/boards/ad7160eval.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xffc03800,
···
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_RA158Z)
 static struct resource bf52x_ra158z_resources[] = {
 	{
 		.start = IRQ_PPI_ERROR,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ad7160eval_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "linux kernel(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 #endif
 
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 4,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 30000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7160)
 #include <linux/input/ad7160.h>
 static const struct ad7160_platform_data bfin_ad7160_ts_info = {
 	.sensor_x_res = 854,
···
 };
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7160)
 	{
 		I2C_BOARD_INFO("ad7160", 0x33),
 		.irq = IRQ_PH1,
···
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_RA158Z)
 	&bf52x_ra158z_device,
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 	&bfin_rotary_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ad7160eval_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 };

arch/blackfin/mach-bf527/boards/cm_bf527.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xffc03800,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "linux kernel(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 static struct resource bfin_pcmcia_cf_resources[] = {
 	{
 		.start = 0x20310000, /* IO PORT */
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 4,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
 	 && defined(CONFIG_SND_SOC_WM8731_SPI)
 	{
 		.modalias	= "wm8731",
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 8,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition cm_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 	&bfin_pcmcia_cf_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 	&dm9000_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&cm_flash_device,
 #endif
 };

arch/blackfin/mach-bf527/boards/ezbrd.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xffc03800,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezbrd_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "bootloader(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
···
 #endif
 
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 #include <linux/spi/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
 	{
 		.modalias = "ad7879",
 		.platform_data = &bfin_ad7879_ts_info,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
 	 && defined(CONFIG_SND_SOC_WM8731_SPI)
 	{
 		.modalias	= "wm8731",
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 8,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
···
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 	},
 };
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 #include <asm/bfin-lq035q1.h>
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	&bfin_lq035q1_device,
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezbrd_flash_device,
 #endif
 };

arch/blackfin/mach-bf527/boards/ezkit.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xffc03800,
···
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_T350MCQB)
 
 static struct resource bf52x_t350mcqb_resources[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 #include <asm/bfin-lq035q1.h>
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "bootloader(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 static struct resource bfin_pcmcia_cf_resources[] = {
 	{
 		.start = 0x20310000, /* IO PORT */
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 #include <linux/spi/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 
 static const u16 bfin_snd_pin[][7] = {
 	{P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97_pcm = {
 	.name = "bfin-ac97-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.4",
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
 	{
 		.modalias = "ad7879",
 		.platform_data = &bfin_ad7879_ts_info,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 8,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
 #include <linux/mfd/adp5520.h>
 
 	/*
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
 	{
 		I2C_BOARD_INFO("ad7879", 0x2C),
 		.irq = IRQ_PF8,
 		.platform_data = (void *)&bfin_ad7879_ts_info,
 	},
 #endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
 	{
 		I2C_BOARD_INFO("pmic-adp5520", 0x32),
 		.irq = IRQ_PF9,
 		.platform_data = (void *)&adp5520_pdev_data,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
 #endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("ad5252", 0x2f),
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1373)
 	{
 		I2C_BOARD_INFO("adau1373", 0x1A),
 	},
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 	&bfin_pcmcia_cf_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 	&dm9000_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_T350MCQB)
 	&bf52x_t350mcqb_device,
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	&bfin_lq035q1_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 	&bfin_rotary_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
 };

arch/blackfin/mach-bf527/boards/tll6527m.c

···
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) \
-	|| defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 #include <linux/spi/ad7879.h>
 #define LCD_BACKLIGHT_GPIO 0x40
 /* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xffc03800,
···
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 #include <asm/bfin-lq035q1.h>
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition tll6527m_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_DECODER)
 /* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
  * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
  * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
···
 
 #endif
 
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
 #include <linux/input/adxl34x.h>
 static const struct adxl34x_platform_data adxl345_info = {
 	.x_axis_offset = 0,
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) \
-	|| defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
 	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_MCP23S08)
 #include <linux/spi/mcp23s08.h>
 static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
 	.chip[0].is_present = true,
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 /*
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
-	|| defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
 	{
 		.modalias = "ad7879",
 		.platform_data = &bfin_ad7879_ts_info,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 10000000,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_MCP23S08)
 	{
 		.modalias = "mcp23s08",
 		.platform_data = &bfin_mcp23s08_sys_gpio_info,
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
 
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
-	|| defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
 	{
 		I2C_BOARD_INFO("ad7879", 0x2C),
 		.irq = IRQ_PH14,
 		.platform_data = (void *)&bfin_ad7879_ts_info,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
···
 	{
 		I2C_BOARD_INFO("ltc3576", 0x09),
 	},
-#if defined(CONFIG_INPUT_ADXL34X_I2C) \
-	|| defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
 	{
 		I2C_BOARD_INFO("adxl34x", 0x53),
 		.irq = IRQ_PH13,
···
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) \
-	|| defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	&bfin_lq035q1_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) \
-	|| defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&tll6527m_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_DECODER)
 	&spi_decoded_gpio,
 #endif
 };

arch/blackfin/mach-bf533/boards/H8606.c

···
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/irq.h>
···
  */
 const char bfin_board_name[] = "HV Sistemas H8606";
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
···
 /*
 *  Driver needs to know address, irq and flag pin.
  */
- #if	defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader (spi)",
···
 /* Notice: for blackfin, the speed_hz is the value of register
  * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 16,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_8250)
 
 #include <linux/serial_8250.h>
 #include <linux/serial.h>
···
 
 #endif
 
-#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES)
 
 /*
  * Configuration for one OpenCores keyboard controller in FPGA at address 0x20200030,
···
 #endif
 
 static struct platform_device *h8606_devices[] __initdata = {
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if	defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 	&dm9000_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_8250)
 	&serial8250_device,
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES)
 	&opencores_kbd_device,
 #endif
 };
···
 	printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n");
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(h8606_devices, ARRAY_SIZE(h8606_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 	return 0;

arch/blackfin/mach-bf533/boards/blackstamp.c

···
  */
 const char bfin_board_name[] = "BlackStamp";
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
···
 /*
  *  Driver needs to know address, irq and flag pin.
  */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 	&i2c_gpio_device,
 #endif
 };
···
 	if (ret < 0)
 		return ret;
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	/*
 	 * setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC.
 	 * the bfin-async-map driver takes care of flipping between

arch/blackfin/mach-bf533/boards/cm_bf533.c

···
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
 #include <linux/spi/mmc_spi.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/irq.h>
···
  */
 const char bfin_board_name[] = "Bluetechnix CM BF533";
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80",       /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 #include <linux/smsc911x.h>
 
 static struct resource smsc911x_resources[] = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20308000,
···
 #endif
 
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 
 
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition para_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 	&smsc911x_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&para_flash_device,
 #endif
 };
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 	return 0;

arch/blackfin/mach-bf533/boards/ezkit.c

···
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/irq.h>
···
  */
 const char bfin_board_name[] = "ADI BF533-EZKIT";
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
···
  *  USB-LAN EzExtender board
  *  Driver needs to know address, irq and flag pin.
  */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions_a[] = {
 	{
 		.name       = "bootloader(nor a)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
 static struct platdata_mtd_ram sram_data_a = {
 	.mapname   = "Flash A SRAM",
 	.bankwidth = 2,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 4,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
···
 };
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
 };
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97 = {
 	.name = "bfin-ac97",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device_a,
 	&ezkit_flash_device_b,
 #endif
 
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
 	&sram_device_a,
 	&sram_device_b,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 	&i2c_gpio_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97,
 #endif
 };

arch/blackfin/mach-bf533/boards/ip0x.c

···
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <asm/irq.h>
···
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 
 #include <linux/dm9000.h>
 
···
 #endif
 
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,		/* if 1 - block!!! */
 };
···
 /* Notice: for blackfin, the speed_hz is the value of register
  * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 2,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20300000,
···
 
 static struct platform_device *ip0x_devices[] __initdata = {
 #if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 	&dm9000_device1,
 	&dm9000_device2,
 #endif
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&spi_bfin_master_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 };

arch/blackfin/mach-bf533/boards/stamp.c

···
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
 #include <linux/spi/mmc_spi.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/irq.h>
···
  */
 const char bfin_board_name[] = "ADI BF533-STAMP";
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
···
 /*
  *  Driver needs to know address, irq and flag pin.
  */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_BFIN_ASYNC) || defined(CONFIG_MTD_BFIN_ASYNC_MODULE)
+#if IS_ENABLED(CONFIG_MTD_BFIN_ASYNC)
 static struct mtd_partition stamp_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 static int bfin_mmc_spi_init(struct device *dev,
 	irqreturn_t (*detect_int)(int, void *), void *data)
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	{
 		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || \
-	defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
 static struct resource bfin_sport0_resources[] = {
 	{
 		.start = SPORT0_TCR1,
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+#if IS_ENABLED(CONFIG_JOYSTICK_AD7142)
 	{
 		I2C_BOARD_INFO("ad7142_joystick", 0x2C),
 		.irq = 39,
 	},
 #endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = 39,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("ad5252", 0x2f),
 	},
···
 	},
 };
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
-	defined(CONFIG_SND_BF5XX_AC97) || \
-	defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+	IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 
 #include <asm/bfin_sport.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97_pcm = {
 	.name = "bfin-ac97-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.4",
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
 static const unsigned ad73311_gpio[] = {
 	GPIO_PF4,
 };
···
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
 static struct platform_device bfin_ad73311_codec_device = {
 	.name = "ad73311",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_AD74111) || defined(CONFIG_SND_SOC_AD74111_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD74111)
 static struct platform_device bfin_ad74111_codec_device = {
 	.name = "ad74111",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || \
-	defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
 static struct platform_device bfin_ac97 = {
 	.name = "bfin-ac97",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || \
-	defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 	&i2c_gpio_device,
 #endif
 
-#if defined(CONFIG_MTD_BFIN_ASYNC) || defined(CONFIG_MTD_BFIN_ASYNC_MODULE)
+#if IS_ENABLED(CONFIG_MTD_BFIN_ASYNC)
 	&stamp_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
 	&bfin_ad73311_machine,
 #endif
 
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
 	&bfin_ad73311_codec_device,
 #endif
 
-#if defined(CONFIG_SND_SOC_AD74111) || defined(CONFIG_SND_SOC_AD74111_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD74111)
 	&bfin_ad74111_codec_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || \
-	defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
 	&bfin_ac97,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	/* Set PF0 to 0, PF1 to 1 make /AMS3 work properly */
···
 	if (ret < 0)
 		return ret;
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	/*
 	 * setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC.
 	 * the bfin-async-map driver takes care of flipping between

arch/blackfin/mach-bf537/boards/cm_bf537e.c

···
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
···
  */
 const char bfin_board_name[] = "Bluetechnix CM BF537E";
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
 
 /* SPORT SPI controller data */
 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
···
 
 #endif  /* sport spi master and devices */
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 static struct platform_device hitachi_fb_device = {
 	.name = "hitachi-tx09",
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20308000,
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition cm_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) \
-|| defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
+|| IS_ENABLED(CONFIG_BFIN_SPORT)
 unsigned short bfin_sport0_peripherals[] = {
 	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
 };
 #endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 };
 #endif
 #endif
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
 static struct resource bfin_sport0_resources[] = {
 	{
 		.start = SPORT0_TCR1,
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define PATA_INT	IRQ_PF14
 
 static struct pata_platform_info bfin_pata_platform_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
 	&bfin_sport0_device,
 #endif
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 	&hitachi_fb_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
 	&bfin_sport_spi0_device,
 	&bfin_sport_spi1_device,
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&cm_flash_device,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PG14, "net2272");
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
 

arch/blackfin/mach-bf537/boards/cm_bf537u.c

···
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
···
  */
 const char bfin_board_name[] = "Bluetechnix CM BF537U";
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 static struct platform_device hitachi_fb_device = {
 	.name = "hitachi-tx09",
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20308000,
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20200000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition cm_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define PATA_INT	IRQ_PF14
 
 static struct pata_platform_info bfin_pata_platform_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 	&hitachi_fb_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&cm_flash_device,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PH15, driver_name);
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
 

arch/blackfin/mach-bf537/boards/dnp5370.c

···
 #define FLASH_MAC               0x202f0000
 #define CONFIG_MTD_PHYSMAP_LEN  0x300000
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition asmb_flash_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma    = 0,	 /* use no dma transfer with this chip*/
···
 
 #endif
 
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 /* This mapping is for at45db642 it has 1056 page size,
  * partition size and offset should be page aligned
  */
···
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 /* SD/MMC card reader at SPI bus */
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias	 = "mmc_spi",
 		.max_speed_hz    = 20000000,
···
 #endif
 
 /* 8 Megabyte Atmel NOR flash chip at SPI bus */
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 	{
 	.modalias        = "mtd_dataflash",
 	.max_speed_hz    = 16700000,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 
 static struct platform_device *dnp5370_devices[] __initdata = {
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&asmb_flash_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&spi_bfin_master_device,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 

arch/blackfin/mach-bf537/boards/minotaur.c

···
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
···
  */
 const char bfin_board_name[] = "CamSig Minotaur BF537";
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 static struct resource bfin_pcmcia_cf_resources[] = {
 	{
 		.start = 0x20310000, /* IO PORT */
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 
 /* Partition sizes */
 #define FLASH_SIZE       0x00400000
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 
 static struct platform_device *minotaur_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 	&bfin_pcmcia_cf_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(minotaur_devices, ARRAY_SIZE(minotaur_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info,
 				ARRAY_SIZE(bfin_spi_board_info));
 #endif

arch/blackfin/mach-bf537/boards/pnav10.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 static struct resource bfin_pcmcia_cf_resources[] = {
 	{
 		.start = 0x20310000, /* IO PORT */
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 4,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 {
 	.modalias		= "ad7877",
 	.platform_data		= &bfin_ad7877_ts_info,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
 static struct platform_device bfin_fb_device = {
 	.name = "bf537-lq035",
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 
 static struct platform_device *stamp_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 	&bfin_pcmcia_cf_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
 	&bfin_fb_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info,
 				ARRAY_SIZE(bfin_spi_board_info));
 #endif

arch/blackfin/mach-bf537/boards/stamp.c

···
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/i2c.h>
···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 static struct resource bfin_pcmcia_cf_resources[] = {
 	{
 		.start = 0x20310000, /* IO PORT */
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
···
 };
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_SL811_HCD)
 static struct resource sl811_hcd_resources[] = {
 	{
 		.start = 0x20340000,
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20360000,
···
 };
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 static unsigned short bfin_can_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
 };
···
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
 const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL };
 
 static struct mtd_partition bfin_plat_nand_partitions[] = {
···
 static void bfin_plat_nand_init(void) {}
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition stamp_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_SPI)
 #include <linux/input/ad714x.h>
 
 static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_I2C)
 #include <linux/input/ad714x.h>
 static struct ad714x_button_plat ad7142_i2c_button_plat[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
+#if IS_ENABLED(CONFIG_AD2S90)
 static struct bfin5xx_spi_chip ad2s90_spi_chip_info = {
 	.enable_dma = 0,
 };
···
 };
 #endif
 
-#if defined(CONFIG_AD2S1210) || defined(CONFIG_AD2S1210_MODULE)
+#if IS_ENABLED(CONFIG_AD2S1210)
 static unsigned short ad2s1210_platform_data[] = {
 	/* use as SAMPLE, A0, A1 */
 	GPIO_PF7, GPIO_PF8, GPIO_PF9,
···
 };
 #endif
 
-#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+#if IS_ENABLED(CONFIG_AD7816)
 static unsigned short ad7816_platform_data[] = {
 	GPIO_PF4, /* rdwr_pin */
 	GPIO_PF5, /* convert_pin */
···
 };
 #endif
 
-#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+#if IS_ENABLED(CONFIG_ADT7310)
 static unsigned long adt7310_platform_data[3] = {
 /* INT bound temperature alarm event. line 1 */
 	IRQ_PG4, IRQF_TRIGGER_LOW,
···
 };
 #endif
 
-#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+#if IS_ENABLED(CONFIG_AD7298)
 static unsigned short ad7298_platform_data[] = {
 	GPIO_PF7, /* busy_pin */
 	0,
 };
 #endif
 
-#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_SPI)
 static unsigned long adt7316_spi_data[2] = {
 	IRQF_TRIGGER_LOW, /* interrupt flags */
 	GPIO_PF7, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 
 static int bfin_mmc_spi_init(struct device *dev,
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 #include <linux/spi/ad7877.h>
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 #include <linux/spi/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
 #include <linux/input/adxl34x.h>
 static const struct adxl34x_platform_data adxl34x_info = {
 	.x_axis_offset = 0,
···
 };
 #endif
 
-#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
+#if IS_ENABLED(CONFIG_ENC28J60)
 static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
 	.enable_dma	= 1,
 };
 #endif
 
-#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
+#if IS_ENABLED(CONFIG_ADF702X)
 #include <linux/spi/adf702x.h>
 #define TXREG 0x0160A470
 static const u32 adf7021_regs[] = {
···
 static inline void adf702x_mac_init(void) {}
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_ADS7846)
 #include <linux/spi/ads7846.h>
 static int ads7873_get_pendown_state(void)
 {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_DATAFLASH) \
-	|| defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 
 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_AD7476) || defined(CONFIG_AD7476_MODULE)
+#if IS_ENABLED(CONFIG_AD7476)
 static struct bfin5xx_spi_chip spi_ad7476_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_MTD_DATAFLASH) \
-	|| defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 	{	/* DataFlash chip */
 		.modalias = "mtd_dataflash",
 		.max_speed_hz = 33250000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	{
 		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_SPI)
 	{
 		.modalias = "ad714x_captouch",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
+#if IS_ENABLED(CONFIG_AD2S90)
 	{
 		.modalias = "ad2s90",
 		.bus_num = 0,
···
 	},
 #endif
 
-#if defined(CONFIG_AD2S1210) || defined(CONFIG_AD2S1210_MODULE)
+#if IS_ENABLED(CONFIG_AD2S1210)
 	{
 		.modalias = "ad2s1210",
 		.max_speed_hz = 8192000,
···
 	},
 #endif
 
-#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+#if IS_ENABLED(CONFIG_AD7816)
 	{
 		.modalias = "ad7818",
 		.max_speed_hz = 1000000,
···
 	},
 #endif
 
-#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+#if IS_ENABLED(CONFIG_ADT7310)
 	{
 		.modalias = "adt7310",
 		.max_speed_hz = 1000000,
···
 	},
 #endif
 
-#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+#if IS_ENABLED(CONFIG_AD7298)
 	{
 		.modalias = "ad7298",
 		.max_speed_hz = 1000000,
···
 	},
 #endif
 
-#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_SPI)
 	{
 		.modalias = "adt7316",
 		.max_speed_hz = 1000000,
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select  = 1,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
 	{
 		.modalias = "ad7879",
 		.platform_data = &bfin_ad7879_ts_info,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
+#if IS_ENABLED(CONFIG_ENC28J60)
 	{
 		.modalias = "enc28j60",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
 	{
 		.modalias	= "adxl34x",
 		.platform_data	= &adxl34x_info,
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
+#if IS_ENABLED(CONFIG_ADF702X)
 	{
 		.modalias = "adf702x",
 		.max_speed_hz = 16000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_ADS7846)
 	{
 		.modalias = "ads7846",
 		.max_speed_hz = 2000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_AD7476) \
-	|| defined(CONFIG_AD7476_MODULE)
+#if IS_ENABLED(CONFIG_AD7476)
 	{
 		.modalias = "ad7476", /* Name of spi_driver for this device */
 		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_ADE7753) \
-	|| defined(CONFIG_ADE7753_MODULE)
+#if IS_ENABLED(CONFIG_ADE7753)
 	{
 		.modalias = "ade7753",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_1,
 	},
 #endif
-#if defined(CONFIG_ADE7754) \
-	|| defined(CONFIG_ADE7754_MODULE)
+#if IS_ENABLED(CONFIG_ADE7754)
 	{
 		.modalias = "ade7754",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_1,
 	},
 #endif
-#if defined(CONFIG_ADE7758) \
-	|| defined(CONFIG_ADE7758_MODULE)
+#if IS_ENABLED(CONFIG_ADE7758)
 	{
 		.modalias = "ade7758",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_1,
 	},
 #endif
-#if defined(CONFIG_ADE7759) \
-	|| defined(CONFIG_ADE7759_MODULE)
+#if IS_ENABLED(CONFIG_ADE7759)
 	{
 		.modalias = "ade7759",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_1,
 	},
 #endif
-#if defined(CONFIG_ADE7854_SPI) \
-	|| defined(CONFIG_ADE7854_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADE7854_SPI)
 	{
 		.modalias = "ade7854",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_ADIS16060) \
-	|| defined(CONFIG_ADIS16060_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16060)
 	{
 		.modalias = "adis16060_r",
 		.max_speed_hz = 2900000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_1,
 	},
 #endif
-#if defined(CONFIG_ADIS16130) \
-	|| defined(CONFIG_ADIS16130_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16130)
 	{
 		.modalias = "adis16130",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_ADIS16201) \
-	|| defined(CONFIG_ADIS16201_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16201)
 	{
 		.modalias = "adis16201",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16203) \
-	|| defined(CONFIG_ADIS16203_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16203)
 	{
 		.modalias = "adis16203",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16204) \
-	|| defined(CONFIG_ADIS16204_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16204)
 	{
 		.modalias = "adis16204",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16209) \
-	|| defined(CONFIG_ADIS16209_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16209)
 	{
 		.modalias = "adis16209",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16220) \
-	|| defined(CONFIG_ADIS16220_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16220)
 	{
 		.modalias = "adis16220",
 		.max_speed_hz = 2000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16240) \
-	|| defined(CONFIG_ADIS16240_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16240)
 	{
 		.modalias = "adis16240",
 		.max_speed_hz = 1500000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16260) \
-	|| defined(CONFIG_ADIS16260_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16260)
 	{
 		.modalias = "adis16260",
 		.max_speed_hz = 1500000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16261) \
-	|| defined(CONFIG_ADIS16261_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16261)
 	{
 		.modalias = "adis16261",
 		.max_speed_hz = 2500000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_ADIS16300) \
-	|| defined(CONFIG_ADIS16300_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16300)
 	{
 		.modalias = "adis16300",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16350) \
-	|| defined(CONFIG_ADIS16350_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16350)
 	{
 		.modalias = "adis16364",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 		.irq = IRQ_PF4,
 	},
 #endif
-#if defined(CONFIG_ADIS16400) \
-	|| defined(CONFIG_ADIS16400_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16400)
 	{
 		.modalias = "adis16400",
 		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
 
 /* SPORT SPI controller data */
 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
···
 
 #endif  /* sport spi master and devices */
 
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
 static struct platform_device bfin_fb_device = {
 	.name = "bf537_lq035",
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 #include <asm/bfin-lq035q1.h>
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
···
 };
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_capture.h>
 #include <media/blackfin/ppi.h>
···
 	.pin_req = ppi_req,
 };
 
-#if defined(CONFIG_VIDEO_VS6624) \
-	|| defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
 static struct v4l2_input vs6624_inputs[] = {
 	{
 		.index = 0,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_ADP5588)
 static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
 	[0]	 = KEY_GRAVE,
 	[1]	 = KEY_1,
···
 };
 #endif
 
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
 #include <linux/mfd/adp5520.h>
 
 	/*
···
 
 #endif
 
-#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_ADP5588)
 static struct adp5588_gpio_platform_data adp5588_gpio_data = {
 	.gpio_start = 50,
 	.pullup_dis_mask = 0,
 };
 #endif
 
-#if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8870)
 #include <linux/i2c/adp8870.h>
 static struct led_info adp8870_leds[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8860)
 #include <linux/i2c/adp8860.h>
 static struct led_info adp8860_leds[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
 static struct regulator_consumer_supply ad5398_consumer = {
 	.supply = "current",
 };
···
 	.consumer_supplies     = &ad5398_consumer,
 };
 
-#if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
-	defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_VIRTUAL_CONSUMER)
 static struct platform_device ad5398_virt_consumer_device = {
 	.name = "reg-virt-consumer",
 	.id = 0,
···
 	},
 };
 #endif
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
-	defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
 static struct regulator_bulk_data ad5398_bulk_data = {
 	.supply = "current",
 };
···
 #endif
 #endif
 
-#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+#if IS_ENABLED(CONFIG_ADT7410)
 /* INT bound temperature alarm event. line 1 */
 static unsigned long adt7410_platform_data[2] = {
 	IRQ_PG4, IRQF_TRIGGER_LOW,
 };
 #endif
 
-#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_I2C)
 /* INT bound temperature alarm event. line 1 */
 static unsigned long adt7316_i2c_data[2] = {
 	IRQF_TRIGGER_LOW, /* interrupt flags */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_SOC_ADAV80X) || defined(CONFIG_SND_SOC_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAV80X)
 	{
 		I2C_BOARD_INFO("adav803", 0x10),
 	},
 #endif
 
-#if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_I2C)
 	{
 		I2C_BOARD_INFO("ad7142_captouch", 0x2C),
 		.irq = IRQ_PG5,
···
 	},
 #endif
 
-#if defined(CONFIG_AD7150) || defined(CONFIG_AD7150_MODULE)
+#if IS_ENABLED(CONFIG_AD7150)
 	{
 		I2C_BOARD_INFO("ad7150", 0x48),
 		.irq = IRQ_PG5, /* fixme: use real interrupt number */
 	},
 #endif
 
-#if defined(CONFIG_AD7152) || defined(CONFIG_AD7152_MODULE)
+#if IS_ENABLED(CONFIG_AD7152)
 	{
 		I2C_BOARD_INFO("ad7152", 0x48),
 	},
 #endif
 
-#if defined(CONFIG_AD774X) || defined(CONFIG_AD774X_MODULE)
+#if IS_ENABLED(CONFIG_AD774X)
 	{
 		I2C_BOARD_INFO("ad774x", 0x48),
 	},
 #endif
 
-#if defined(CONFIG_ADE7854_I2C) || defined(CONFIG_ADE7854_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADE7854_I2C)
 	{
 		I2C_BOARD_INFO("ade7854", 0x38),
 	},
···
 	},
 #endif
 
-#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+#if IS_ENABLED(CONFIG_ADT7410)
 	{
 		I2C_BOARD_INFO("adt7410", 0x48),
 		/* CT critical temperature event. line 0 */
···
 	},
 #endif
 
-#if defined(CONFIG_AD7291) || defined(CONFIG_AD7291_MODULE)
+#if IS_ENABLED(CONFIG_AD7291)
 	{
 		I2C_BOARD_INFO("ad7291", 0x20),
 		.irq = IRQ_PG5,
 	},
 #endif
 
-#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_I2C)
 	{
 		I2C_BOARD_INFO("adt7316", 0x48),
 		.irq = IRQ_PG6,
···
 	},
 #endif
 
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PG6,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
 	{
 		I2C_BOARD_INFO("ad7879", 0x2F),
 		.irq = IRQ_PG5,
 		.platform_data = (void *)&bfin_ad7879_ts_info,
 	},
 #endif
-#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_ADP5588)
 	{
 		I2C_BOARD_INFO("adp5588-keys", 0x34),
 		.irq = IRQ_PG0,
 		.platform_data = (void *)&adp5588_kpad_data,
 	},
 #endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
 	{
 		I2C_BOARD_INFO("pmic-adp5520", 0x32),
 		.irq = IRQ_PG0,
 		.platform_data = (void *)&adp5520_pdev_data,
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
 	{
 		I2C_BOARD_INFO("adxl34x", 0x53),
 		.irq = IRQ_PG3,
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
-#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_ADP5588)
 	{
 		I2C_BOARD_INFO("adp5588-gpio", 0x34),
 		.platform_data = (void *)&adp5588_gpio_data,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
 	{
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
 	{
 		I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2F),
 	},
 #endif
-#if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8870)
 	{
 		I2C_BOARD_INFO("adp8870", 0x2B),
 		.platform_data = (void *)&adp8870_pdata,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1371) || defined(CONFIG_SND_SOC_ADAU1371_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1371)
 	{
 		I2C_BOARD_INFO("adau1371", 0x1A),
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
 	{
 		I2C_BOARD_INFO("adau1761", 0x38),
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1361) || defined(CONFIG_SND_SOC_ADAU1361_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1361)
 	{
 		I2C_BOARD_INFO("adau1361", 0x38),
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1701) || defined(CONFIG_SND_SOC_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1701)
 	{
 		I2C_BOARD_INFO("adau1701", 0x34),
 	},
 #endif
-#if defined(CONFIG_AD525X_DPOT) || defined(CONFIG_AD525X_DPOT_MODULE)
+#if IS_ENABLED(CONFIG_AD525X_DPOT)
 	{
 		I2C_BOARD_INFO("ad5258", 0x18),
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
 #endif
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
 	{
 		I2C_BOARD_INFO("ad5398", 0xC),
 		.platform_data = (void *)&ad5398_regulator_data,
 	},
 #endif
-#if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8860)
 	{
 		I2C_BOARD_INFO("adp8860", 0x2A),
 		.platform_data = (void *)&adp8860_pdata,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1373)
 	{
 		I2C_BOARD_INFO("adau1373", 0x1A),
 	},
 #endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("ad5252", 0x2e),
 	},
 #endif
 };
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) \
-|| defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
+|| IS_ENABLED(CONFIG_BFIN_SPORT)
 unsigned short bfin_sport0_peripherals[] = {
 	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
 };
 #endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 };
 #endif
 #endif
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
 static struct resource bfin_sport0_resources[] = {
 	{
 		.start = SPORT0_TCR1,
···
 	},
 };
 #endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
 /* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
 
···
 	},
 };
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
-	defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+	IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 
 #define SPORT_REQ(x) \
 	[x] = {P_SPORT##x##_TFS, P_SPORT##x##_DTPRI, P_SPORT##x##_TSCLK, \
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97_pcm = {
 	.name = "bfin-ac97-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.4",
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
-				defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
 static const unsigned ad73311_gpio[] = {
 	GPIO_PF4,
 };
···
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
 static struct platform_device bfin_ad73311_codec_device = {
 	.name = "ad73311",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X)
 static struct platform_device bfin_eval_adav801_device = {
 	.name = "bfin-eval-adav801",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
 static struct platform_device bfin_ac97 = {
 	.name = "bfin-ac97",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_FIXED_VOLTAGE)
 #define REGULATOR_ADP122	"adp122"
 #define REGULATOR_ADP122_UV	2500000
 
···
 	},
 };
 
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
-	defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
 static struct regulator_bulk_data adp122_bulk_data = {
 	.supply = REGULATOR_ADP122,
 };
···
 #endif
 #endif
 
-#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
-	defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+#if IS_ENABLED(CONFIG_IIO_GPIO_TRIGGER)
 
 static struct resource iio_gpio_trigger_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373)
 static struct platform_device bf5xx_adau1373_device = {
 	.name = "bfin-eval-adau1373",
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701)
 static struct platform_device bf5xx_adau1701_device = {
 	.name = "bfin-eval-adau1701",
 };
···
 static struct platform_device *stamp_devices[] __initdata = {
 
 	&bfin_dpmc,
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
 	&bfin_sport0_device,
 #endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
 	&bfin_pcmcia_cf_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_SL811_HCD)
 	&sl811_hcd_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
 	&dm9000_device,
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
 	&bfin_sport_spi0_device,
 	&bfin_sport_spi1_device,
 #endif
 
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
 	&bfin_fb_device,
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	&bfin_lq035q1_device,
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 	&bfin_capture_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
 	&bfin_async_nand_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&stamp_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
-		defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
 	&bfin_ad73311_machine,
 #endif
 
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
 	&bfin_ad73311_codec_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
 	&bfin_ac97,
 #endif
 
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
-#if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
-	defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
+#if IS_ENABLED(CONFIG_REGULATOR_VIRTUAL_CONSUMER)
 	&ad5398_virt_consumer_device,
 #endif
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
-	defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
 	&ad5398_userspace_consumer_device,
 #endif
 #endif
 
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_FIXED_VOLTAGE)
 	&adp_switch_device,
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
-	defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
 	&adp122_userspace_consumer_device,
 #endif
 #endif
 
-#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
-	defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+#if IS_ENABLED(CONFIG_IIO_GPIO_TRIGGER)
 	&iio_gpio_trigger,
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373)
 	&bf5xx_adau1373_device,
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701)
 	&bf5xx_adau1701_device,
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X)
 	&bfin_eval_adav801_device,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PF6, "net2272");

arch/blackfin/mach-bf537/boards/tcm_bf537.c

···
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
···
  */
 const char bfin_board_name[] = "Bluetechnix TCM BF537";
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 	},
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 static struct platform_device hitachi_fb_device = {
 	.name = "hitachi-tx09",
 };
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20308000,
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition cm_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;
 
···
 };
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define PATA_INT	IRQ_PF14
 
 static struct pata_platform_info bfin_pata_platform_data = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 	&hitachi_fb_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif
 
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&cm_flash_device,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PG14, "net2272");
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
 

arch/blackfin/mach-bf538/boards/ezkit.c

···
  */
 
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif	/* CONFIG_RTC_DRV_BFIN */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif	/* CONFIG_SERIAL_BFIN_UART2 */
 #endif	/* CONFIG_SERIAL_BFIN */
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif	/* CONFIG_BFIN_SIR2 */
 #endif	/* CONFIG_BFIN_SIR */
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif	/* CONFIG_SERIAL_BFIN_SPORT3_UART */
 #endif	/* CONFIG_SERIAL_BFIN_SPORT */
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 static unsigned short bfin_can_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
 };
···
  *  USB-LAN EzExtender board
  *  Driver needs to know address, irq and flag pin.
  */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif	/* CONFIG_SMC91X */
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 /* SPI flash chip (m25p16) */
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
···
 #endif	/* CONFIG_MTD_M25P80 */
 #endif	/* CONFIG_SPI_BFIN5XX */
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
 #include <linux/spi/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
···
 };
 #endif	/* CONFIG_TOUCHSCREEN_AD7879 */
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 #include <asm/bfin-lq035q1.h>
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
···
 #endif	/* CONFIG_FB_BFIN_LQ035Q1 */
 
 static struct spi_board_info bf538_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif	/* CONFIG_MTD_M25P80 */
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
 	{
 		.modalias = "ad7879",
 		.platform_data = &bfin_ad7879_ts_info,
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif	/* CONFIG_TOUCHSCREEN_AD7879_SPI */
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif	/* CONFIG_FB_BFIN_LQ035Q1 */
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		},
 };
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 };
 #endif	/* CONFIG_I2C_BLACKFIN_TWI */
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
···
 	},
 };
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 
 static struct resource ezkit_flash_resource = {
 	.start = 0x20000000,
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	.end   = 0x202fffff,
 #else
 	.end   = 0x203fffff,
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bf538_spi_master0,
 	&bf538_spi_master1,
 	&bf538_spi_master2,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi0_device,
 	&i2c_bfin_twi1_device,
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	&bfin_lq035q1_device,
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
 };
···
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf538_devices, ARRAY_SIZE(cm_bf538_devices));
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bf538_spi_board_info,
 			ARRAY_SIZE(bf538_spi_board_info));
 #endif

arch/blackfin/mach-bf548/boards/cm_bf548.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
 
 #include <mach/bf54x-lq043.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
 static unsigned int bf548_keymap[] = {
 	KEYVAL(0, 0, KEY_ENTER),
 	KEYVAL(0, 1, KEY_HELP),
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 #include <linux/smsc911x.h>
 
 static struct resource smsc911x_resources[] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xFFC03C00,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
 static struct resource bfin_atapi_resources[] = {
 	{
 		.start = 0xFFC03800,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "linux kernel(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_SDH,
 	.irq_int0 = IRQ_SDH_MASK0,
···
 };
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 static unsigned short bfin_can_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
 };
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition para_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 /* SPI flash chip (m25p16) */
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bf54x_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 {
 	.modalias		= "ad7877",
 	.platform_data		= &bfin_ad7877_ts_info,
···
 	.chip_select  		= 2,
 },
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
 	&bf54x_lq043_device,
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 	&smsc911x_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
 	&bfin_atapi_device,
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bf54x_sdh_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bf54x_spi_master0,
 	&bf54x_spi_master1,
 #endif
 
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
 	&bf54x_kpad_device,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi0_device,
 #if !defined(CONFIG_BF542)
 	&i2c_bfin_twi1_device,
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&para_flash_device,
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can_device,
 #endif
 
···
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf548_devices, ARRAY_SIZE(cm_bf548_devices));
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bf54x_spi_board_info,
 			ARRAY_SIZE(bf54x_spi_board_info));
 #endif

arch/blackfin/mach-bf548/boards/ezkit.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
 
 #include <mach/bf54x-lq043.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
 static const unsigned int bf548_keymap[] = {
 	KEYVAL(0, 0, KEY_ENTER),
 	KEYVAL(0, 1, KEY_HELP),
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
 #include <linux/input/adxl34x.h>
 static const struct adxl34x_platform_data adxl34x_info = {
 	.x_axis_offset = 0,
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 #include <linux/smsc911x.h>
 
 static struct resource smsc911x_resources[] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xFFC03C00,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 
 static unsigned short bfin_can0_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
···
 
 #endif
 
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
 static struct resource bfin_atapi_resources[] = {
 	{
 		.start = 0xFFC03800,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "bootloader(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_SDH,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 /* SPI flash chip (m25p16) */
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = MAX_CTRL_CS + GPIO_PG6, /* SPI_SSEL2 */
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select		= MAX_CTRL_CS + GPIO_PE5, /* SPI_SSEL2 */
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = MAX_CTRL_CS + GPIO_PE4, /* SPI_SSEL1 */
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
 	{
 		.modalias		= "adxl34x",
 		.platform_data		= &adxl34x_info,
···
 	},
 #endif
 };
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_capture.h>
 #include <media/blackfin/ppi.h>
···
 	.pin_req = ppi_req,
 };
 
-#if defined(CONFIG_VIDEO_VS6624) \
-	|| defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
 static struct v4l2_input vs6624_inputs[] = {
 	{
 		.index = 0,
···
 };
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
···
 
 #if !defined(CONFIG_BF542)	/* The BF542 only has 1 TWI */
 static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = 212,
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
 	{
 		I2C_BOARD_INFO("adxl34x", 0x53),
 		.irq = IRQ_PC5,
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("ad5252", 0x2f),
 	},
···
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
···
 	},
 };
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
-	defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+	IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 
 #define SPORT_REQ(x) \
 	[x] = {P_SPORT##x##_TFS, P_SPORT##x##_DTPRI, P_SPORT##x##_TSCLK, \
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97_pcm = {
 	.name = "bfin-ac97-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
 static struct platform_device bfin_ad73311_codec_device = {
 	.name = "ad73311",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1980) || defined(CONFIG_SND_BF5XX_SOC_AD1980_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980)
 static struct platform_device bfin_ad1980_codec_device = {
 	.name = "ad1980",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
 static struct platform_device bfin_ac97 = {
 	.name = "bfin-ac97",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 	&bfin_gpj_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
 	&bf54x_lq043_device,
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 	&smsc911x_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can0_device,
 	&bfin_can1_device,
 #endif
 
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
 	&bfin_atapi_device,
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bf5xx_nand_device,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bf54x_sdh_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bf54x_spi_master0,
 	&bf54x_spi_master1,
 #endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 	&bfin_capture_device,
 #endif
 
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
 	&bf54x_kpad_device,
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 	&bfin_rotary_device,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi0_device,
 #if !defined(CONFIG_BF542)
 	&i2c_bfin_twi1_device,
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97_pcm,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1980) || defined(CONFIG_SND_BF5XX_SOC_AD1980_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980)
 	&bfin_ad1980_codec_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97,
 #endif
 };

arch/blackfin/mach-bf561/boards/acvilon.c

···
  */
 const char bfin_board_name[] = "Acvilon board";
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 	 },
 };
 
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
 static struct platdata_mtd_ram mtd_ram_data = {
 	.mapname = "rootfs(RAM)",
 	.bankwidth = 4,
···
 };
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 #include <linux/smsc911x.h>
 static struct resource smsc911x_resources[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
 
 static struct mtd_partition bfin_plat_nand_partitions[] = {
 	{
···
 }
 #endif
 
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 	{
 	 .name = "bootloader",
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 	 .modalias = "spidev",
 	 .max_speed_hz = 3125000,	/* max spi clock (SCK) speed in HZ */
···
 	 .chip_select = 3,
 	 },
 #endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 	{			/* DataFlash chip */
 	 .modalias = "mtd_dataflash",
 	 .max_speed_hz = 33250000,	/* max spi clock (SCK) speed in HZ */
···
 static struct platform_device *acvilon_devices[] __initdata = {
 	&bfin_dpmc,
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 
 	&bfin_gpios_device,
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 	&smsc911x_device,
 #endif
 
 	&bfin_i2c_pca_device,
 
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
 	&bfin_async_nand_device,
 #endif
 
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
 	&mtd_ram_device,
 #endif
 

arch/blackfin/mach-bf561/boards/cm_bf561.c

···
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
···
  */
 const char bfin_board_name[] = "Bluetechnix CM BF561";
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */
 
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 	},
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.chip_select = 4,
 	},
 #endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
···
 #endif  /* spi master and devices */
 
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 static struct platform_device hitachi_fb_device = {
 	.name = "hitachi-tx09",
 };
 #endif
 
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 #include <linux/smsc911x.h>
 
 static struct resource smsc911x_resources[] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x24000000,
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x24008000,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define PATA_INT	IRQ_PF46
 
 static struct pata_platform_info bfin_pata_platform_data = {
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition para_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 	&hitachi_fb_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
 	&smsc911x_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&para_flash_device,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PF46, "net2272");
···
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
 
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
 

arch/blackfin/mach-bf561/boards/ezkit.c

···
  */
 const char bfin_board_name[] = "ADI BF561-EZKIT";
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 
 static struct resource isp1362_hcd_resources[] = {
···
 };
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x2C000000,
···
  *  USB-LAN EzExtender board
  *  Driver needs to know address, irq and flag pin.
  */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>
 
 static struct smc91x_platdata smc91x_info = {
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 #endif
 };
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
···
 	},
 };
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_capture.h>
 #include <media/blackfin/ppi.h>
···
 	.pin_req = ppi_req,
 };
 
-#if defined(CONFIG_VIDEO_ADV7183) \
-	|| defined(CONFIG_VIDEO_ADV7183_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7183)
 #include <media/adv7183.h>
 static struct v4l2_input adv7183_inputs[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 static struct platform_device bfin_ac97 = {
 	.name = "bfin-ac97",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.4",
···
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif
 
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
 	&i2c_gpio_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 	&bfin_capture_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
 	&bfin_ac97,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
 };
 
 static int __init net2272_init(void)
 {
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;
 
 	ret = gpio_request(GPIO_PF11, "net2272");
···
 	if (ret < 0)
 		return ret;
 
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
 	bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 12));
 	SSYNC();
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
 	bfin_write_FIO0_FLAG_S(1 << 15);
 	SSYNC();

arch/blackfin/mach-bf561/boards/tepla.c

···
 	.resource      = smc91x_resources,
 };
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 static struct platform_device *tepla_devices[] __initdata = {
 	&smc91x_device,
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif

arch/blackfin/mach-bf609/boards/ezkit.c

···
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
···
 };
 #endif
 
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
 #include <linux/stmmac.h>
 #include <linux/phy.h>
 
···
 };
 #endif
 
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
 #include <linux/input/adxl34x.h>
 static const struct adxl34x_platform_data adxl34x_info = {
 	.x_axis_offset = 0,
···
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xFFCC1000,
···
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
···
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 
 static unsigned short bfin_can0_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
···
 
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "bootloader(nand)",
···
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_RSI,
···
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
···
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 /* SPI flash chip (w25q32) */
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 static struct bfin_spi3_chip spidev_chip_info = {
 	.enable_dma = true,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
 #include <asm/bfin_sport3.h>
 static struct resource bfin_snd_resources[] = {
 	{
···
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.76",
···
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
 static struct platform_device adau1761_device = {
 	.name = "bfin-eval-adau1x61",
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
 #include <sound/adau17x1.h>
 static struct adau1761_platform_data adau1761_info = {
 	.lineout_mode = ADAU1761_OUTPUT_MODE_LINE,
···
 };
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_capture.h>
 #include <media/blackfin/ppi.h>
···
 	P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7,
 	P_PPI0_D8, P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
 	P_PPI0_D12, P_PPI0_D13, P_PPI0_D14, P_PPI0_D15,
-#if !defined(CONFIG_VIDEO_VS6624) && !defined(CONFIG_VIDEO_VS6624_MODULE)
+#if !IS_ENABLED(CONFIG_VIDEO_VS6624)
 	P_PPI0_D16, P_PPI0_D17, P_PPI0_D18, P_PPI0_D19,
 	P_PPI0_D20, P_PPI0_D21, P_PPI0_D22, P_PPI0_D23,
 #endif
···
 	.pin_req = ppi_req,
 };
 
-#if defined(CONFIG_VIDEO_VS6624) \
-	|| defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
 static struct v4l2_input vs6624_inputs[] = {
 	{
 		.index = 0,
···
 };
 #endif
 
-#if defined(CONFIG_VIDEO_ADV7842) \
-	|| defined(CONFIG_VIDEO_ADV7842_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7842)
 #include <media/adv7842.h>
 
 static struct v4l2_input adv7842_inputs[] = {
···
 };
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_display.h>
 #include <media/blackfin/ppi.h>
···
 	.pin_req = ppi_req_disp,
 };
 
-#if defined(CONFIG_VIDEO_ADV7511) \
-	|| defined(CONFIG_VIDEO_ADV7511_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7511)
 #include <media/adv7511.h>
 
 static struct v4l2_output adv7511_outputs[] = {
···
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
···
 
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
···
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
···
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
···
 		.chip_select		= MAX_CTRL_CS + GPIO_PC15, /* SPI_SSEL4 */
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
···
 		.controller_data = &spidev_chip_info,
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
 	{
 		.modalias		= "adxl34x",
 		.platform_data		= &adxl34x_info,
···
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
···
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
 	{
 		I2C_BOARD_INFO("adxl34x", 0x53),
 		.irq = IRQ_PC5,
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
 	{
 		I2C_BOARD_INFO("adau1761", 0x38),
 		.platform_data = (void *)&adau1761_info
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
···
 	&bfin_gpg_device,
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
 	&bfin_eth_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
···
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can0_device,
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bfin_nand_device,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bfin_sdh_device,
 #endif
 
···
 	&bf60x_spi_master1,
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 	&bfin_rotary_device,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi0_device,
 #if !defined(CONFIG_BF542)
 	&i2c_bfin_twi1_device,
···
 	&bfin_crypto_crc_device,
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
 	&bfin_i2s,
 #endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
 	&adau1761_device,
 #endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 	&bfin_capture_device,
 #endif
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
 	&bfin_display_device,
 #endif
 
···
 	PIN_MAP_MUX_GROUP_DEFAULT("physmap-flash.0",  "pinctrl-adi2.0", NULL, "smc0"),
 	PIN_MAP_MUX_GROUP_DEFAULT("bf609_nl8048.2",  "pinctrl-adi2.0", NULL, "ppi2_16b"),
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin_display.0",  "pinctrl-adi2.0", NULL, "ppi0_16b"),
-#if defined(CONFIG_VIDEO_MT9M114) || defined(CONFIG_VIDEO_MT9M114_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_MT9M114)
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0",  "pinctrl-adi2.0", NULL, "ppi0_8b"),
-#elif defined(CONFIG_VIDEO_VS6624) || defined(CONFIG_VIDEO_VS6624_MODULE)
+#elif IS_ENABLED(CONFIG_VIDEO_VS6624)
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0",  "pinctrl-adi2.0", NULL, "ppi0_16b"),
 #else
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0",  "pinctrl-adi2.0", NULL, "ppi0_24b"),