Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.

Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.

All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"

Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt

···
 - reg-io-width : the size (in bytes) of the IO accesses that should be
   performed on the device.  If this property is not present then single byte
   accesses are used.
+- dcd-override : Override the DCD modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- dsr-override : Override the DTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- cts-override : Override the CTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- ri-override : Override the RI modem status signal. This signal will always be
+  reported as inactive instead of being obtained from the modem status register.
+  Define this if your serial port does not use this pin.
 
 Example:
 
···
 		interrupts = <10>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		dcd-override;
+		dsr-override;
+		cts-override;
+		ri-override;
 	};
 
 Example with one clock:

drivers/tty/bfin_jtag_comm.c

···
 	return circ_cnt(&bfin_jc_write_buf);
 }
 
-static void
-bfin_jc_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-	unsigned long expire = jiffies + timeout;
-	while (!circ_empty(&bfin_jc_write_buf)) {
-		if (signal_pending(current))
-			break;
-		if (time_after(jiffies, expire))
-			break;
-	}
-}
-
 static const struct tty_operations bfin_jc_ops = {
 	.open            = bfin_jc_open,
 	.close           = bfin_jc_close,
···
 	.flush_chars     = bfin_jc_flush_chars,
 	.write_room      = bfin_jc_write_room,
 	.chars_in_buffer = bfin_jc_chars_in_buffer,
-	.wait_until_sent = bfin_jc_wait_until_sent,
 };
 
 static int __init bfin_jc_init(void)

drivers/tty/serial/8250/8250_core.c

···
 	/*
 	 * Clear the interrupt registers.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 
···
 	 * saved flags to avoid getting false values from polling
 	 * routines or the previous session.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 	up->lsr_saved_flags = 0;
···
 	 * Read data port to reset things, and then unlink from
 	 * the IRQ chain.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_RX);
 	serial8250_rpm_put(up);
 
 	del_timer_sync(&up->timer);

drivers/tty/serial/8250/8250_dw.c

···
 	u8			usr_reg;
 	int			last_mcr;
 	int			line;
+	int			msr_mask_on;
+	int			msr_mask_off;
 	struct clk		*clk;
 	struct clk		*pclk;
 	struct reset_control	*rst;
···
 	if (offset == UART_MSR && d->last_mcr & UART_MCR_AFE) {
 		value |= UART_MSR_CTS;
 		value &= ~UART_MSR_DCTS;
+	}
+
+	/* Override any modem control signals if needed */
+	if (offset == UART_MSR) {
+		value |= d->msr_mask_on;
+		value &= ~d->msr_mask_off;
 	}
 
 	return value;
···
 	id = of_alias_get_id(np, "serial");
 	if (id >= 0)
 		p->line = id;
+
+	if (of_property_read_bool(np, "dcd-override")) {
+		/* Always report DCD as active */
+		data->msr_mask_on |= UART_MSR_DCD;
+		data->msr_mask_off |= UART_MSR_DDCD;
+	}
+
+	if (of_property_read_bool(np, "dsr-override")) {
+		/* Always report DSR as active */
+		data->msr_mask_on |= UART_MSR_DSR;
+		data->msr_mask_off |= UART_MSR_DDSR;
+	}
+
+	if (of_property_read_bool(np, "cts-override")) {
+		/* Always report DSR as active */
+		data->msr_mask_on |= UART_MSR_DSR;
+		data->msr_mask_off |= UART_MSR_DDSR;
+	}
+
+	if (of_property_read_bool(np, "ri-override")) {
+		/* Always report Ring indicator as inactive */
+		data->msr_mask_off |= UART_MSR_RI;
+		data->msr_mask_off |= UART_MSR_TERI;
+	}
 
 	/* clock got configured through clk api, all done */
 	if (p->uartclk)

drivers/tty/serial/8250/8250_pci.c

···
 	       "Please send the output of lspci -vv, this\n"
 	       "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
 	       "manufacturer and name of serial board or\n"
-	       "modem board to [e-mail].\n",
+	       "modem board to <[e-mail]>.\n",
 	       pci_name(dev), str, dev->vendor, dev->device,
 	       dev->subsystem_vendor, dev->subsystem_device);
 }
···
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_QRK_UART,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_default_setup,
-	},
-	{
-		.vendor		= PCI_VENDOR_ID_INTEL,
 		.device		= PCI_DEVICE_ID_INTEL_BSW_UART1,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
···
 	/*
 	 * PLX
 	 */
-	{
-		.vendor		= PCI_VENDOR_ID_PLX,
-		.device		= PCI_DEVICE_ID_PLX_9030,
-		.subvendor	= PCI_SUBVENDOR_ID_PERLE,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_default_setup,
-	},
 	{
 		.vendor		= PCI_VENDOR_ID_PLX,
 		.device		= PCI_DEVICE_ID_PLX_9050,
···
 		0, 0, pbn_b0_bt_4_115200 },
 
 	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH353_2S1PF,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0, 0, pbn_b0_bt_2_115200 },
-
-	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S,
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_b0_bt_2_115200 },
 

drivers/tty/serial/of_serial.c

···
 	if (of_find_property(np, "no-loopback-test", NULL))
 		port->flags |= UPF_SKIP_TEST;
 
-	ret = of_alias_get_id(np, "serial");
-	if (ret >= 0)
-		port->line = ret;
-
 	port->dev = &ofdev->dev;
 
 	switch (type) {

drivers/tty/serial/sprd_serial.c

···
 
 	ims = serial_in(port, SPRD_IMSR);
 
-	if (!ims)
+	if (!ims) {
+		spin_unlock(&port->lock);
 		return IRQ_NONE;
+	}
 
 	serial_out(port, SPRD_ICLR, ~0);
 

drivers/tty/tty_io.c

···
 /* We limit tty time update visibility to every 8 seconds or so. */
 static void tty_update_time(struct timespec *time)
 {
-	unsigned long sec = get_seconds() & ~7;
-	if ((long)(sec - time->tv_sec) > 0)
+	unsigned long sec = get_seconds();
+	if (abs(sec - time->tv_sec) & ~7)
 		time->tv_sec = sec;
 }
 

drivers/tty/tty_ioctl.c

···
 #endif
 	if (!timeout)
 		timeout = MAX_SCHEDULE_TIMEOUT;
-	if (wait_event_interruptible_timeout(tty->write_wait,
-			!tty_chars_in_buffer(tty), timeout) >= 0) {
-		if (tty->ops->wait_until_sent)
-			tty->ops->wait_until_sent(tty, timeout);
-	}
+
+	timeout = wait_event_interruptible_timeout(tty->write_wait,
+			!tty_chars_in_buffer(tty), timeout);
+	if (timeout <= 0)
+		return;
+
+	if (timeout == MAX_SCHEDULE_TIMEOUT)
+		timeout = 0;
+
+	if (tty->ops->wait_until_sent)
+		tty->ops->wait_until_sent(tty, timeout);
 }
 EXPORT_SYMBOL(tty_wait_until_sent);
 

drivers/usb/serial/generic.c

···
 	 * character or at least one jiffy.
 	 */
 	period = max_t(unsigned long, (10 * HZ / bps), 1);
-	period = min_t(unsigned long, period, timeout);
+	if (timeout)
+		period = min_t(unsigned long, period, timeout);
 
 	dev_dbg(&port->dev, "%s - timeout = %u ms, period = %u ms\n",
 					__func__, jiffies_to_msecs(timeout),
···
 		schedule_timeout_interruptible(period);
 		if (signal_pending(current))
 			break;
-		if (time_after(jiffies, expire))
+		if (timeout && time_after(jiffies, expire))
 			break;
 	}
 }

include/linux/serial_core.h

···
 	unsigned char		iotype;			/* io access style */
 	unsigned char		unused1;
 
-#define UPIO_PORT		(0)			/* 8b I/O port access */
-#define UPIO_HUB6		(1)			/* Hub6 ISA card */
-#define UPIO_MEM		(2)			/* 8b MMIO access */
-#define UPIO_MEM32		(3)			/* 32b little endian */
-#define UPIO_MEM32BE		(4)			/* 32b big endian */
-#define UPIO_AU			(5)			/* Au1x00 and RT288x type IO */
-#define UPIO_TSI		(6)			/* Tsi108/109 type IO */
+#define UPIO_PORT		(SERIAL_IO_PORT)	/* 8b I/O port access */
+#define UPIO_HUB6		(SERIAL_IO_HUB6)	/* Hub6 ISA card */
+#define UPIO_MEM		(SERIAL_IO_MEM)		/* 8b MMIO access */
+#define UPIO_MEM32		(SERIAL_IO_MEM32)	/* 32b little endian */
+#define UPIO_AU			(SERIAL_IO_AU)		/* Au1x00 and RT288x type IO */
+#define UPIO_TSI		(SERIAL_IO_TSI)		/* Tsi108/109 type IO */
+#define UPIO_MEM32BE		(SERIAL_IO_MEM32BE)	/* 32b big endian */
 
 	unsigned int		read_status_mask;	/* driver specific */
 	unsigned int		ignore_status_mask;	/* driver specific */

include/uapi/linux/serial.h

···
 #define SERIAL_IO_PORT	0
 #define SERIAL_IO_HUB6	1
 #define SERIAL_IO_MEM	2
+#define SERIAL_IO_MEM32	  3
+#define SERIAL_IO_AU	  4
+#define SERIAL_IO_TSI	  5
+#define SERIAL_IO_MEM32BE 6
 
 #define UART_CLEAR_FIFO		0x01
 #define UART_USE_FIFO		0x02

kernel/printk/console_cmdline.h

···
 
 struct console_cmdline
 {
-	char	name[8];			/* Name of the driver	    */
+	char	name[16];			/* Name of the driver	    */
 	int	index;				/* Minor dev. to use	    */
 	char	*options;			/* Options for the driver   */
 #ifdef CONFIG_A11Y_BRAILLE_CONSOLE

kernel/printk/printk.c

···
 	for (i = 0, c = console_cmdline;
 	     i < MAX_CMDLINECONSOLES && c->name[0];
 	     i++, c++) {
+		BUILD_BUG_ON(sizeof(c->name) != sizeof(newcon->name));
 		if (strcmp(c->name, newcon->name) != 0)
 			continue;
 		if (newcon->index >= 0 &&

net/irda/ircomm/ircomm_tty.c

···
 	orig_jiffies = jiffies;
 
 	/* Set poll time to 200 ms */
-	poll_time = IRDA_MIN(timeout, msecs_to_jiffies(200));
+	poll_time = msecs_to_jiffies(200);
+	if (timeout)
+		poll_time = min_t(unsigned long, timeout, poll_time);
 
 	spin_lock_irqsave(&self->spinlock, flags);
 	while (self->tx_skb && self->tx_skb->len) {