Merge tag 'arm-soc/for-6.14/devicetree-arm64' of https://github.com/Broadcom/stblinux into soc/dt

This pull request contains Broadcom ARM64-based SoCs Device Tree updates
for 6.14:

- Dave adds the display pipeline DT nodes on BCM2712 (Raspberry Pi 5)

- Rob removes some undocumented properties

- Same ensures that the CFE stub area is reserved to allow secondary
CPUs to be successfully brought up in Linux, also making sure that the
address used in the spin table is also carved out. Finally he adds
support for the Zyxel EX3510-B router using BCM4906

- Rosen converts the BCM4908 platforms to use the more flexible
nvmem-layout representation

* tag 'arm-soc/for-6.14/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: bcm4908: nvmem-layout conversion
arm64: dts: broadcom: bcmbca: bcm4908: Add DT for Zyxel EX3510-B
dt-bindings: arm64: bcmbca: Add Zyxel EX3510-B based on BCM4906
arm64: dts: broadcom: bcmbca: bcm4908: Protect cpu-release-addr
arm64: dts: broadcom: bcmbca: bcm4908: Reserve CFE stub area
arm64: dts: broadcom: Remove unused and undocumented properties
arm64: dts: broadcom: Add DT for D-step version of BCM2712
arm64: dts: broadcom: Add display pipeline support to BCM2712
arm64: dts: broadcom: Add firmware clocks and power nodes to Pi5 DT

Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Arnd Bergmann <[e-mail]>

Documentation/devicetree/bindings/arm/bcm/brcm,bcmbca.yaml

···
           - enum:
               - netgear,r8000p
               - tplink,archer-c2300-v1
+              - zyxel,ex3510b
           - const: brcm,bcm4906
           - const: brcm,bcm4908
           - const: brcm,bcmbca

arch/arm64/boot/dts/broadcom/Makefile

···
 			      bcm2711-rpi-4-b.dtb \
 			      bcm2711-rpi-cm4-io.dtb \
 			      bcm2712-rpi-5-b.dtb \
+			      bcm2712-d-rpi-5-b.dtb \
 			      bcm2837-rpi-3-a-plus.dtb \
 			      bcm2837-rpi-3-b.dtb \
 			      bcm2837-rpi-3-b-plus.dtb \

arch/arm64/boot/dts/broadcom/bcm2712-d-rpi-5-b.dts

···
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+
+#include "bcm2712-rpi-5-b.dts"
+
+&gio_aon {
+	brcm,gpio-bank-widths = <15 6>;
+
+	gpio-line-names =
+		"RP1_SDA", // AON_GPIO_00
+		"RP1_SCL", // AON_GPIO_01
+		"RP1_RUN", // AON_GPIO_02
+		"SD_IOVDD_SEL", // AON_GPIO_03
+		"SD_PWR_ON", // AON_GPIO_04
+		"SD_CDET_N", // AON_GPIO_05
+		"SD_FLG_N", // AON_GPIO_06
+		"", // AON_GPIO_07
+		"2712_WAKE", // AON_GPIO_08
+		"2712_STAT_LED", // AON_GPIO_09
+		"", // AON_GPIO_10
+		"", // AON_GPIO_11
+		"PMIC_INT", // AON_GPIO_12
+		"UART_TX_FS", // AON_GPIO_13
+		"UART_RX_FS", // AON_GPIO_14
+		"", // AON_GPIO_15
+		"", // AON_GPIO_16
+
+		// Pad bank0 out to 32 entries
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+
+		"HDMI0_SCL", // AON_SGPIO_00
+		"HDMI0_SDA", // AON_SGPIO_01
+		"HDMI1_SCL", // AON_SGPIO_02
+		"HDMI1_SDA", // AON_SGPIO_03
+		"PMIC_SCL", // AON_SGPIO_04
+		"PMIC_SDA"; // AON_SGPIO_05
+};

arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts

···
 	sd-uhs-ddr50;
 	sd-uhs-sdr104;
 };
+
+&soc {
+	firmware: firmware {
+		compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mboxes = <&mailbox>;
+		dma-ranges;
+
+		firmware_clocks: clocks {
+			compatible = "raspberrypi,firmware-clocks";
+			#clock-cells = <1>;
+		};
+
+		reset: reset {
+			compatible = "raspberrypi,firmware-reset";
+			#reset-cells = <1>;
+		};
+	};
+
+	power: power {
+		compatible = "raspberrypi,bcm2835-power";
+		firmware = <&firmware>;
+		#power-domain-cells = <1>;
+	};
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>, <&firmware_clocks 16>;
+	clock-names = "core", "disp";
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+};

arch/arm64/boot/dts/broadcom/bcm2712.dtsi

···
 			#mbox-cells = <0>;
 		};
 
-		local_intc: interrupt-controller@7cd00000 {
-			compatible = "brcm,bcm2836-l1-intc";
-			reg = <0x7cd00000 0x100>;
-		};
-
 		uart10: serial@7d001000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x7d001000 0x200>;
···
 			interrupt-controller;
 			#interrupt-cells = <3>;
 		};
+
+		aon_intr: interrupt-controller@7d510600 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7d510600 0x30>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		pixelvalve0: pixelvalve@7c410000 {
+			compatible = "brcm,bcm2712-pixelvalve0";
+			reg = <0x7c410000 0x100>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pixelvalve1: pixelvalve@7c411000 {
+			compatible = "brcm,bcm2712-pixelvalve1";
+			reg = <0x7c411000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		mop: mop@7c500000 {
+			compatible = "brcm,bcm2712-mop";
+			reg = <0x7c500000 0x28>;
+			interrupt-parent = <&disp_intr>;
+			interrupts = <1>;
+		};
+
+		moplet: moplet@7c501000 {
+			compatible = "brcm,bcm2712-moplet";
+			reg = <0x7c501000 0x20>;
+			interrupt-parent = <&disp_intr>;
+			interrupts = <0>;
+		};
+
+		disp_intr: interrupt-controller@7c502000 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7c502000 0x30>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		dvp: clock@7c700000 {
+			compatible = "brcm,brcm2711-dvp";
+			reg = <0x7c700000 0x10>;
+			clocks = <&clk_108MHz>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		ddc0: i2c@7d508200 {
+			compatible = "brcm,brcmstb-i2c";
+			reg = <0x7d508200 0x58>;
+			interrupt-parent = <&bsc_irq>;
+			interrupts = <1>;
+			clock-frequency = <97500>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ddc1: i2c@7d508280 {
+			compatible = "brcm,brcmstb-i2c";
+			reg = <0x7d508280 0x58>;
+			interrupt-parent = <&bsc_irq>;
+			interrupts = <2>;
+			clock-frequency = <97500>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		bsc_irq: interrupt-controller@7d508380 {
+			compatible = "brcm,bcm7271-l2-intc";
+			reg = <0x7d508380 0x10>;
+			interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		main_irq: interrupt-controller@7d508400 {
+			compatible = "brcm,bcm7271-l2-intc";
+			reg = <0x7d508400 0x10>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		hdmi0: hdmi@7c701400 {
+			compatible = "brcm,bcm2712-hdmi0";
+			reg = <0x7c701400 0x300>,
+			      <0x7c701000 0x200>,
+			      <0x7c701d00 0x300>,
+			      <0x7c702000 0x80>,
+			      <0x7c703800 0x200>,
+			      <0x7c704000 0x800>,
+			      <0x7c700100 0x80>,
+			      <0x7d510800 0x100>,
+			      <0x7c720000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			resets = <&dvp 1>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <1>, <2>, <3>,
+				     <7>, <8>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "hpd-connected", "hpd-removed";
+			ddc = <&ddc0>;
+		};
+
+		hdmi1: hdmi@7c706400 {
+			compatible = "brcm,bcm2712-hdmi1";
+			reg = <0x7c706400 0x300>,
+			      <0x7c706000 0x200>,
+			      <0x7c706d00 0x300>,
+			      <0x7c707000 0x80>,
+			      <0x7c708800 0x200>,
+			      <0x7c709000 0x800>,
+			      <0x7c700180 0x80>,
+			      <0x7d511000 0x100>,
+			      <0x7c720000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			resets = <&dvp 2>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <11>, <12>, <13>,
+				     <14>, <15>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "hpd-connected", "hpd-removed";
+			ddc = <&ddc1>;
+		};
+	};
+
+	axi: axi {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		ranges = <0x00 0x00000000  0x00 0x00000000  0x10 0x00000000>,
+			 <0x10 0x00000000  0x10 0x00000000  0x01 0x00000000>,
+			 <0x14 0x00000000  0x14 0x00000000  0x04 0x00000000>,
+			 <0x18 0x00000000  0x18 0x00000000  0x04 0x00000000>,
+			 <0x1c 0x00000000  0x1c 0x00000000  0x04 0x00000000>;
+
+		dma-ranges = <0x00 0x00000000  0x00 0x00000000  0x10 0x00000000>,
+			     <0x10 0x00000000  0x10 0x00000000  0x01 0x00000000>,
+			     <0x14 0x00000000  0x14 0x00000000  0x04 0x00000000>,
+			     <0x18 0x00000000  0x18 0x00000000  0x04 0x00000000>,
+			     <0x1c 0x00000000  0x1c 0x00000000  0x04 0x00000000>;
+
+		vc4: gpu {
+			compatible = "brcm,bcm2712-vc6";
+		};
 	};
 
 	timer {
···
 					  IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(4) |
 					  IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	clk_27MHz: clk-27M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <27000000>;
+		clock-output-names = "27MHz-clock";
+	};
+
+	clk_108MHz: clk-108M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <108000000>;
+		clock-output-names = "108MHz-clock";
+	};
+
+	hvs: hvs@107c580000 {
+		compatible = "brcm,bcm2712-hvs";
+		reg = <0x10 0x7c580000 0x0 0x1a000>;
+		interrupt-parent = <&disp_intr>;
+		interrupts = <2>, <9>, <16>;
+		interrupt-names = "ch0-eof", "ch1-eof", "ch2-eof";
 	};
 };

arch/arm64/boot/dts/broadcom/bcmbca/Makefile

···
 dtb-$(CONFIG_ARCH_BCMBCA) += \
 				bcm4906-netgear-r8000p.dtb \
 				bcm4906-tplink-archer-c2300-v1.dtb \
+				bcm4906-zyxel-ex3510b.dtb \
 				bcm4908-asus-gt-ac5300.dtb \
 				bcm4908-netgear-raxe500.dtb \
 				bcm94908.dtb \

arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-netgear-r8000p.dts

···
 		#size-cells = <1>;
 
 		partition@0 {
-			compatible = "nvmem-cells";
 			label = "cferom";
 			reg = <0x0 0x100000>;
-
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x0 0x100000>;
 
-			base_mac_addr: mac@106a0 {
-				reg = <0x106a0 0x6>;
+			nvmem-layout {
+				compatible = "fixed-layout";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				base_mac_addr: mac@106a0 {
+					reg = <0x106a0 0x6>;
+				};
 			};
 		};
 

arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts

···
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "bcm4906.dtsi"
+
+/ {
+	compatible = "zyxel,ex3510b", "brcm,bcm4906", "brcm,bcm4908", "brcm,bcmbca";
+	model = "Zyxel EX3510-B";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x20000000>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		key-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+		};
+
+		key-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&leds {
+	pinctrl-0 = <&pins_led_0_a>, <&pins_led_2_a>, <&pins_led_3_a>,
+		    <&pins_led_4_a>, <&pins_led_10_a>, <&pins_led_12_a>,
+		    <&pins_led_14_a>, <&pins_led_15_a>, <&pins_led_21_a>;
+	pinctrl-names = "default";
+
+	led@0 {
+		reg = <0x0>;
+		function = LED_FUNCTION_POWER;
+		color = <LED_COLOR_ID_RED>;
+	};
+
+	led@2 {
+		reg = <0x2>;
+		function = LED_FUNCTION_WAN_ONLINE;
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@3 {
+		reg = <0x3>;
+		function = LED_FUNCTION_WAN_ONLINE;
+		color = <LED_COLOR_ID_RED>;
+	};
+
+	led@4 {
+		reg = <0x4>;
+		function = LED_FUNCTION_USB;
+		color = <LED_COLOR_ID_GREEN>;
+		trigger-sources = <&ohci_port1>, <&ohci_port2>,
+				  <&ehci_port1>, <&ehci_port2>,
+				  <&xhci_port1>, <&xhci_port2>;
+		linux,default-trigger = "usbport";
+	};
+
+	led@a {
+		reg = <0xa>;
+		function = LED_FUNCTION_POWER;
+		color = <LED_COLOR_ID_GREEN>;
+		linux,default-trigger = "default-on";
+	};
+
+	led@c {
+		reg = <0xc>;
+		function = LED_FUNCTION_LAN;
+		color = <LED_COLOR_ID_GREEN>;
+		active-low;
+	};
+
+	led@e {
+		reg = <0xe>;
+		function = LED_FUNCTION_WPS;
+		color = <LED_COLOR_ID_GREEN>;
+		active-low;
+	};
+
+	led@f {
+		reg = <0xf>;
+		function = LED_FUNCTION_WPS;
+		color = <LED_COLOR_ID_RED>;
+		active-low;
+	};
+
+	led@15 {
+		reg = <0x15>;
+		function = LED_FUNCTION_WAN;
+		color = <LED_COLOR_ID_GREEN>;
+		active-low;
+	};
+};
+
+&enet {
+	nvmem-cells = <&base_mac_addr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&usb_phy {
+	brcm,ioc = <1>;
+	brcm,ipp = <1>;
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan1";
+	};
+
+	port@1 {
+		label = "lan2";
+	};
+
+	port@2 {
+		label = "lan3";
+	};
+
+	port@3 {
+		label = "lan4";
+	};
+
+	port@7 {
+		reg = <7>;
+		phy-mode = "internal";
+		phy-handle = <&phy12>;
+		label = "wan";
+	};
+};
+
+&nand_controller {
+	status = "okay";
+};
+
+&nandcs {
+	brcm,nand-oob-sector-size = <27>;
+	nand-ecc-strength = <8>;
+	nand-ecc-step-size = <512>;
+	nand-on-flash-bbt;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	partitions {
+		compatible = "brcm,bcm4908-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			compatible = "nvmem-cells";
+			label = "cferom";
+			reg = <0x0 0x100000>;
+			read-only;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			base_mac_addr: mac@106a0 {
+				reg = <0x106a0 0x6>;
+			};
+		};
+
+		partition@100000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x100000 0x5f80000>;
+		};
+
+		partition@6080000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x6080000 0x5f80000>;
+		};
+	};
+};

arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi

···
 			compatible = "brcm,brahma-b53";
 			reg = <0x0>;
 			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
+			cpu-release-addr = <0x0 0xff8>;
 			next-level-cache = <&l2>;
 		};
 
···
 			compatible = "brcm,brahma-b53";
 			reg = <0x1>;
 			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
+			cpu-release-addr = <0x0 0xff8>;
 			next-level-cache = <&l2>;
 		};
 
···
 			compatible = "brcm,brahma-b53";
 			reg = <0x2>;
 			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
+			cpu-release-addr = <0x0 0xff8>;
 			next-level-cache = <&l2>;
 		};
 
···
 			compatible = "brcm,brahma-b53";
 			reg = <0x3>;
 			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
+			cpu-release-addr = <0x0 0xff8>;
 			next-level-cache = <&l2>;
 		};
 
···
 			compatible = "cache";
 			cache-level = <2>;
 			cache-unified;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		cfe-stub@0 {
+			reg = <0x0 0x0 0x0 0x1000>;
 		};
 	};
 

arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts

···
 		spi-cpha;
 		spi-cpol;
 		pl022,interface = <0>;
-		pl022,slave-tx-disable = <0>;
 		pl022,com-mode = <0>;
 		pl022,rx-level-trig = <1>;
 		pl022,tx-level-trig = <1>;
···
 };
 
 &qspi {
-	bspi-sel = <0>;
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm64/boot/dts/broadcom/northstar2/ns2-xmc.dts

···
 		#size-cells = <1>;
 		compatible = "m25p80";
 		spi-max-frequency = <62500000>;
-		m25p,default-addr-width = <3>;
 		reg = <0x0 0x0>;
 
 		partition@0 {

arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi

···
 		brcm,pcie-ob;
 		brcm,pcie-ob-oarr-size;
 		brcm,pcie-ob-axi-offset = <0x00000000>;
-		brcm,pcie-ob-window-size = <256>;
 
 		status = "disabled";
 
···
 		brcm,pcie-ob;
 		brcm,pcie-ob-oarr-size;
 		brcm,pcie-ob-axi-offset = <0x30000000>;
-		brcm,pcie-ob-window-size = <256>;
 
 		status = "disabled";