mmc: core: Add definitions for SD UHS-II cards

Add UHS-II specific data structures for commands and defines for
registers, as described in Part 1 UHS-II Addendum Version 1.01.

UHS-II related definitions are listed below:
1. UHS-II card capability: sd_uhs2_caps{}
2. UHS-II configuration: sd_uhs2_config{}
3. UHS-II register I/O address and register field definitions: sd_uhs2.h

Signed-off-by: Jason Lai <[e-mail]>
Signed-off-by: Victor Shih <[e-mail]>
Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Ulf Hansson <[e-mail]>

include/linux/mmc/card.h

···
 #define SD_MAX_CURRENT_400	(1 << SD_SET_CURRENT_LIMIT_400)
 #define SD_MAX_CURRENT_600	(1 << SD_SET_CURRENT_LIMIT_600)
 #define SD_MAX_CURRENT_800	(1 << SD_SET_CURRENT_LIMIT_800)
+
+#define SD4_SET_POWER_LIMIT_0_72W	0
+#define SD4_SET_POWER_LIMIT_1_44W	1
+#define SD4_SET_POWER_LIMIT_2_16W	2
+#define SD4_SET_POWER_LIMIT_2_88W	3
+#define SD4_SET_POWER_LIMIT_1_80W	4
 };
 
 struct sd_ext_reg {
···
 
 struct sd_uhs2_config {
 	u32			node_id;
-	/* TODO: Extend with more register configs. */
+
+	u32			n_fcu;
+	u32			maxblk_len;
+	u8			n_lanes;
+	u8			dadr_len;
+	u8			app_type;
+	u8			phy_minor_rev;
+	u8			phy_major_rev;
+	u8			can_hibernate;
+	u8			n_lss_sync;
+	u8			n_lss_dir;
+	u8			link_minor_rev;
+	u8			link_major_rev;
+	u8			dev_type;
+	u8			n_data_gap;
+
+	u32			n_fcu_set;
+	u32			maxblk_len_set;
+	u8			n_lanes_set;
+	u8			speed_range_set;
+	u8			n_lss_sync_set;
+	u8			n_lss_dir_set;
+	u8			n_data_gap_set;
+	u8			max_retry_set;
 };
 
 struct sdio_cccr {

include/linux/mmc/host.h

···
 #include <linux/mmc/pm.h>
 #include <linux/dma-direction.h>
 #include <linux/blk-crypto-profile.h>
+#include <linux/mmc/sd_uhs2.h>
 
 struct mmc_ios {
 	unsigned int	clock;			/* clock rate */
···
 };
 
 struct sd_uhs2_caps {
-	/* TODO: Add UHS-II capabilities for the host. */
+	u32	dap;
+	u32	gap;
+	u32	group_desc;
+	u32	maxblk_len;
+	u32	n_fcu;
+	u8	n_lanes;
+	u8	addr64;
+	u8	card_type;
+	u8	phy_rev;
+	u8	speed_range;
+	u8	n_lss_sync;
+	u8	n_lss_dir;
+	u8	link_rev;
+	u8	host_type;
+	u8	n_data_gap;
+
+	u32	maxblk_len_set;
+	u32	n_fcu_set;
+	u8	n_lanes_set;
+	u8	n_lss_sync_set;
+	u8	n_lss_dir_set;
+	u8	n_data_gap_set;
+	u8	max_retry_set;
 };
 
 enum sd_uhs2_operation {

include/linux/mmc/sd_uhs2.h

···
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Header file for UHS-II packets, Host Controller registers and I/O
+ * accessors.
+ *
+ *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
+ */
+#ifndef LINUX_MMC_UHS2_H
+#define LINUX_MMC_UHS2_H
+
+/* LINK Layer definition */
+/*
+ * UHS2 Header:
+ * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
+ *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
+ *      bit [6:4]  : TYP(Packet Type)
+ *                   000b: CCMD(Control command packet)
+ *                   001b: DCMD(Data command packet)
+ *                   010b: RES(Response packet)
+ *                   011b: DATA(Data payload packet)
+ *                   111b: MSG(Message packet)
+ *                   Others: Reserved
+ *      bit [7]    : NP(Native Packet)
+ *      bit [10:8] : TID(Transaction ID)
+ *      bit [11]   : Reserved
+ *      bit [15:12]: SID(Source ID 0: Node ID of Host)
+ *
+ * Broadcast CCMD issued by Host is represented as DID=SID=0.
+ */
+/*
+ * UHS2 Argument:
+ * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
+ *      bit [3:0]  : MSB of IOADR
+ *      bit [5:4]  : PLEN(Payload Length)
+ *                   00b: 0 byte
+ *                   01b: 4 bytes
+ *                   10b: 8 bytes
+ *                   11b: 16 bytes
+ *      bit [6]    : Reserved
+ *      bit [7]    : R/W(Read/Write)
+ *                   0: Control read command
+ *                   1: Control write command
+ *      bit [15:8] : LSB of IOADR
+ *
+ * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
+ * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
+ */
+#define UHS2_NATIVE_PACKET_POS	7
+#define UHS2_NATIVE_PACKET	(1 << UHS2_NATIVE_PACKET_POS)
+
+#define UHS2_PACKET_TYPE_POS	4
+#define UHS2_PACKET_TYPE_CCMD	(0 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_DCMD	(1 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_RES	(2 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_DATA	(3 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_MSG	(7 << UHS2_PACKET_TYPE_POS)
+
+#define UHS2_DEST_ID_MASK	0x0F
+#define UHS2_DEST_ID		0x1
+
+#define UHS2_SRC_ID_POS		12
+#define UHS2_SRC_ID_MASK	0xF000
+
+#define UHS2_TRANS_ID_POS	8
+#define UHS2_TRANS_ID_MASK	0x0700
+
+/* UHS2 MSG */
+#define UHS2_MSG_CTG_POS	5
+#define UHS2_MSG_CTG_LMSG	0x00
+#define UHS2_MSG_CTG_INT	0x60
+#define UHS2_MSG_CTG_AMSG	0x80
+
+#define UHS2_MSG_CTG_FCREQ	0x00
+#define UHS2_MSG_CTG_FCRDY	0x01
+#define UHS2_MSG_CTG_STAT	0x02
+
+#define UHS2_MSG_CODE_POS			8
+#define UHS2_MSG_CODE_FC_UNRECOVER_ERR		0x8
+#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR	0x8
+#define UHS2_MSG_CODE_STAT_RECOVER_ERR		0x1
+
+/* TRANS Layer definition */
+
+/* Native packets*/
+#define UHS2_NATIVE_CMD_RW_POS	7
+#define UHS2_NATIVE_CMD_WRITE	(1 << UHS2_NATIVE_CMD_RW_POS)
+#define UHS2_NATIVE_CMD_READ	(0 << UHS2_NATIVE_CMD_RW_POS)
+
+#define UHS2_NATIVE_CMD_PLEN_POS	4
+#define UHS2_NATIVE_CMD_PLEN_4B		(1 << UHS2_NATIVE_CMD_PLEN_POS)
+#define UHS2_NATIVE_CMD_PLEN_8B		(2 << UHS2_NATIVE_CMD_PLEN_POS)
+#define UHS2_NATIVE_CMD_PLEN_16B	(3 << UHS2_NATIVE_CMD_PLEN_POS)
+
+#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK	0xF00
+#define UHS2_NATIVE_CCMD_MIOADR_MASK		0x0F
+
+#define UHS2_NATIVE_CCMD_LIOADR_POS		8
+#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK	0x0FF
+
+#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG	BIT(11)
+#define UHS2_DEV_INIT_PAYLOAD_LEN		1
+#define UHS2_DEV_INIT_RESP_LEN			6
+#define UHS2_DEV_ENUM_PAYLOAD_LEN		1
+#define UHS2_DEV_ENUM_RESP_LEN			8
+#define UHS2_CFG_WRITE_PAYLOAD_LEN		2
+#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN		4
+#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN	5
+#define UHS2_GO_DORMANT_PAYLOAD_LEN		1
+
+/*
+ * UHS2 Argument:
+ * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
+ *      bit [3:0]  : Reserved
+ *      bit [6:3]  : TMODE(Transfer Mode)
+ *                   bit 3: DAM(Data Access Mode)
+ *                   bit 4: TLUM(TLEN Unit Mode)
+ *                   bit 5: LM(Length Mode)
+ *                   bit 6: DM(Duplex Mode)
+ *      bit [7]    : R/W(Read/Write)
+ *                   0: Control read command
+ *                   1: Control write command
+ *      bit [15:8] : Reserved
+ *
+ * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
+ * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
+ */
+#define UHS2_DCMD_DM_POS		6
+#define UHS2_DCMD_2L_HD_MODE		(1 << UHS2_DCMD_DM_POS)
+#define UHS2_DCMD_LM_POS		5
+#define UHS2_DCMD_LM_TLEN_EXIST		(1 << UHS2_DCMD_LM_POS)
+#define UHS2_DCMD_TLUM_POS		4
+#define UHS2_DCMD_TLUM_BYTE_MODE	(1 << UHS2_DCMD_TLUM_POS)
+#define UHS2_NATIVE_DCMD_DAM_POS	3
+#define UHS2_NATIVE_DCMD_DAM_IO		(1 << UHS2_NATIVE_DCMD_DAM_POS)
+
+#define UHS2_RES_NACK_POS	7
+#define UHS2_RES_NACK_MASK	(0x1 << UHS2_RES_NACK_POS)
+
+#define UHS2_RES_ECODE_POS	4
+#define UHS2_RES_ECODE_MASK	0x7
+#define UHS2_RES_ECODE_COND	1
+#define UHS2_RES_ECODE_ARG	2
+#define UHS2_RES_ECODE_GEN	3
+
+/* IOADR of device registers */
+#define UHS2_IOADR_GENERIC_CAPS		0x00
+#define UHS2_IOADR_PHY_CAPS		0x02
+#define UHS2_IOADR_LINK_CAPS		0x04
+#define UHS2_IOADR_RSV_CAPS		0x06
+#define UHS2_IOADR_GENERIC_SETTINGS	0x08
+#define UHS2_IOADR_PHY_SETTINGS		0x0A
+#define UHS2_IOADR_LINK_SETTINGS	0x0C
+#define UHS2_IOADR_PRESET		0x40
+
+/* SD application packets */
+#define UHS2_SD_CMD_INDEX_POS	8
+
+#define UHS2_SD_CMD_APP_POS	14
+#define UHS2_SD_CMD_APP		(1 << UHS2_SD_CMD_APP_POS)
+
+/* UHS-II Device Registers */
+#define UHS2_DEV_CONFIG_REG	0x000
+
+/* General Caps and Settings registers */
+#define UHS2_DEV_CONFIG_GEN_CAPS	(UHS2_DEV_CONFIG_REG + 0x000)
+#define UHS2_DEV_CONFIG_N_LANES_POS	8
+#define UHS2_DEV_CONFIG_N_LANES_MASK	0x3F
+#define UHS2_DEV_CONFIG_2L_HD_FD	0x1
+#define UHS2_DEV_CONFIG_2D1U_FD		0x2
+#define UHS2_DEV_CONFIG_1D2U_FD		0x4
+#define UHS2_DEV_CONFIG_2D2U_FD		0x8
+#define UHS2_DEV_CONFIG_DADR_POS	14
+#define UHS2_DEV_CONFIG_DADR_MASK	0x1
+#define UHS2_DEV_CONFIG_APP_POS		16
+#define UHS2_DEV_CONFIG_APP_MASK	0xFF
+#define UHS2_DEV_CONFIG_APP_SD_MEM	0x1
+
+#define UHS2_DEV_CONFIG_GEN_SET			(UHS2_DEV_CONFIG_REG + 0x008)
+#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS	8
+#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD	0x0
+#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD		0x2
+#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD		0x3
+#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD		0x4
+#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE	BIT(31)
+
+/* PHY Caps and Settings registers */
+#define UHS2_DEV_CONFIG_PHY_CAPS	(UHS2_DEV_CONFIG_REG + 0x002)
+#define UHS2_DEV_CONFIG_PHY_MINOR_MASK	0xF
+#define UHS2_DEV_CONFIG_PHY_MAJOR_POS	4
+#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK	0x3
+#define UHS2_DEV_CONFIG_CAN_HIBER_POS	15
+#define UHS2_DEV_CONFIG_CAN_HIBER_MASK	0x1
+#define UHS2_DEV_CONFIG_PHY_CAPS1	(UHS2_DEV_CONFIG_REG + 0x003)
+#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK	0xF
+#define UHS2_DEV_CONFIG_N_LSS_DIR_POS	4
+#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK	0xF
+
+#define UHS2_DEV_CONFIG_PHY_SET			(UHS2_DEV_CONFIG_REG + 0x00A)
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS	6
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A		0x0
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B		0x1
+
+/* LINK-TRAN Caps and Settings registers */
+#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS		(UHS2_DEV_CONFIG_REG + 0x004)
+#define UHS2_DEV_CONFIG_LT_MINOR_MASK		0xF
+#define UHS2_DEV_CONFIG_LT_MAJOR_POS		4
+#define UHS2_DEV_CONFIG_LT_MAJOR_MASK		0x3
+#define UHS2_DEV_CONFIG_N_FCU_POS		8
+#define UHS2_DEV_CONFIG_N_FCU_MASK		0xFF
+#define UHS2_DEV_CONFIG_DEV_TYPE_POS		16
+#define UHS2_DEV_CONFIG_DEV_TYPE_MASK		0x7
+#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS		20
+#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK	0xFFF
+#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1		(UHS2_DEV_CONFIG_REG + 0x005)
+#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK		0xFF
+
+#define UHS2_DEV_CONFIG_LINK_TRAN_SET		(UHS2_DEV_CONFIG_REG + 0x00C)
+#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN	0x200
+#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS	16
+
+/* Preset register */
+#define UHS2_DEV_CONFIG_PRESET	(UHS2_DEV_CONFIG_REG + 0x040)
+
+#define UHS2_DEV_INT_REG	0x100
+
+#define UHS2_DEV_STATUS_REG	0x180
+
+#define UHS2_DEV_CMD_REG		0x200
+#define UHS2_DEV_CMD_FULL_RESET		(UHS2_DEV_CMD_REG + 0x000)
+#define UHS2_DEV_CMD_GO_DORMANT_STATE	(UHS2_DEV_CMD_REG + 0x001)
+#define UHS2_DEV_CMD_DORMANT_HIBER	BIT(7)
+#define UHS2_DEV_CMD_DEVICE_INIT	(UHS2_DEV_CMD_REG + 0x002)
+#define UHS2_DEV_INIT_COMPLETE_FLAG	BIT(11)
+#define UHS2_DEV_CMD_ENUMERATE		(UHS2_DEV_CMD_REG + 0x003)
+#define UHS2_DEV_CMD_TRANS_ABORT	(UHS2_DEV_CMD_REG + 0x004)
+
+#define UHS2_RCLK_MAX	52000000
+#define UHS2_RCLK_MIN	26000000
+
+#endif /* LINUX_MMC_UHS2_H */