Merge tag 'imx-cleanup-3.10' into imx/soc

The imx cleanup for 3.10:

* Clean up a couple of unneeded function declarations
* Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well
as the replacement
* Remove platform ahci support
* Clean up unused ARCH/MACH Kconfig symbols
* Remove a couple of unused files

arch/arm/Kconfig

···
 
 source "drivers/cpufreq/Kconfig"
 
-config CPU_FREQ_IMX
-	tristate "CPUfreq driver for i.MX CPUs"
-	depends on ARCH_MXC && CPU_FREQ
-	select CPU_FREQ_TABLE
-	help
-	  This enables the CPUfreq driver for i.MX CPUs.
-
 config CPU_FREQ_SA1100
 	bool
 

arch/arm/mach-imx/Kconfig

···
 config ARCH_MX1
 	bool
 
-config MACH_MX21
-	bool
-
 config ARCH_MX25
 	bool
 
 config MACH_MX27
-	bool
-
-config ARCH_MX5
-	bool
-
-config ARCH_MX51
-	bool
-
-config ARCH_MX53
 	bool
 
 config SOC_IMX1
···
 	select COMMON_CLK
 	select CPU_ARM926T
 	select IMX_HAVE_IOMUX_V1
-	select MACH_MX21
 	select MXC_AVIC
 
 config SOC_IMX25
···
 config SOC_IMX5
 	bool
 	select ARCH_HAS_CPUFREQ
-	select ARCH_MX5
 	select ARCH_MXC_IOMUX_V3
 	select COMMON_CLK
 	select CPU_V7
···
 
 config	SOC_IMX51
 	bool
-	select ARCH_MX5
-	select ARCH_MX51
 	select PINCTRL
 	select PINCTRL_IMX51
 	select SOC_IMX5
···
 
 config	SOC_IMX53
 	bool "i.MX53 support"
-	select ARCH_MX5
-	select ARCH_MX53
 	select HAVE_CAN_FLEXCAN if CAN
 	select IMX_HAVE_PLATFORM_IMX2_WDT
 	select PINCTRL

arch/arm/mach-imx/Makefile

···
 obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clk-imx35.o ehci-imx35.o pm-imx3.o
 
 imx5-pm-$(CONFIG_PM) += pm-imx5.o
-obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o $(imx5-pm-y) cpu_op-mx51.o
+obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o $(imx5-pm-y)
 
 obj-$(CONFIG_COMMON_CLK) += clk-pllv1.o clk-pllv2.o clk-pllv3.o clk-gate2.o \
 			    clk-pfd.o clk-busy.o clk.o
···
 obj-$(CONFIG_MXC_ULPI) += ulpi.o
 obj-$(CONFIG_MXC_USE_EPIT) += epit.o
 obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
-obj-$(CONFIG_CPU_FREQ_IMX)    += cpufreq.o
 
 ifeq ($(CONFIG_CPU_IDLE),y)
 obj-y += cpuidle.o

arch/arm/mach-imx/Makefile.boot

···
-zreladdr-$(CONFIG_SOC_IMX1)	+= 0x08008000
-params_phys-$(CONFIG_SOC_IMX1)	:= 0x08000100
-initrd_phys-$(CONFIG_SOC_IMX1)	:= 0x08800000
-
-zreladdr-$(CONFIG_SOC_IMX21)	+= 0xC0008000
-params_phys-$(CONFIG_SOC_IMX21)	:= 0xC0000100
-initrd_phys-$(CONFIG_SOC_IMX21)	:= 0xC0800000
-
-zreladdr-$(CONFIG_SOC_IMX25)	+= 0x80008000
-params_phys-$(CONFIG_SOC_IMX25)	:= 0x80000100
-initrd_phys-$(CONFIG_SOC_IMX25)	:= 0x80800000
-
-zreladdr-$(CONFIG_SOC_IMX27)	+= 0xA0008000
-params_phys-$(CONFIG_SOC_IMX27)	:= 0xA0000100
-initrd_phys-$(CONFIG_SOC_IMX27)	:= 0xA0800000
-
-zreladdr-$(CONFIG_SOC_IMX31)	+= 0x80008000
-params_phys-$(CONFIG_SOC_IMX31)	:= 0x80000100
-initrd_phys-$(CONFIG_SOC_IMX31)	:= 0x80800000
-
-zreladdr-$(CONFIG_SOC_IMX35)	+= 0x80008000
-params_phys-$(CONFIG_SOC_IMX35)	:= 0x80000100
-initrd_phys-$(CONFIG_SOC_IMX35)	:= 0x80800000
-
-zreladdr-$(CONFIG_SOC_IMX51)	+= 0x90008000
-params_phys-$(CONFIG_SOC_IMX51)	:= 0x90000100
-initrd_phys-$(CONFIG_SOC_IMX51)	:= 0x90800000
-
-zreladdr-$(CONFIG_SOC_IMX53)	+= 0x70008000
-params_phys-$(CONFIG_SOC_IMX53)	:= 0x70000100
-initrd_phys-$(CONFIG_SOC_IMX53)	:= 0x70800000
-
-zreladdr-$(CONFIG_SOC_IMX6Q)	+= 0x10008000
-params_phys-$(CONFIG_SOC_IMX6Q)	:= 0x10000100
-initrd_phys-$(CONFIG_SOC_IMX6Q)	:= 0x10800000

arch/arm/mach-imx/avic.c

···
 void __iomem *avic_base;
 static struct irq_domain *domain;
 
-static u32 avic_saved_mask_reg[2];
-
 #ifdef CONFIG_MXC_IRQ_PRIOR
 static int avic_irq_set_priority(unsigned char irq, unsigned char prio)
 {
···
 };
 
 #ifdef CONFIG_PM
+static u32 avic_saved_mask_reg[2];
+
 static void avic_irq_suspend(struct irq_data *d)
 {
 	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);

arch/arm/mach-imx/clk-imx27.c

···
 	clk_register_clkdev(clk[scc_ipg_gate], "scc", NULL);
 	clk_register_clkdev(clk[cpu_div], "cpu", NULL);
 	clk_register_clkdev(clk[emi_ahb_gate], "emi_ahb" , NULL);
-	clk_register_clkdev(clk[ssi1_baud_gate], "bitrate" , "imx-ssi.0");
-	clk_register_clkdev(clk[ssi2_baud_gate], "bitrate" , "imx-ssi.1");
 
 	mxc_timer_init(MX27_IO_ADDRESS(MX27_GPT1_BASE_ADDR), MX27_INT_GPT1);
 

arch/arm/mach-imx/common.h

···
 extern u32 imx_get_cpu_arg(int cpu);
 extern void imx_set_cpu_arg(int cpu, u32 arg);
 extern void v7_cpu_resume(void);
-extern u32 *pl310_get_save_ptr(void);
 #ifdef CONFIG_SMP
 extern void v7_secondary_startup(void);
 extern void imx_scu_map_io(void);
···
 static inline void imx_smp_prepare(void) {}
 static inline void imx_scu_standby_enable(void) {}
 #endif
-extern void imx_enable_cpu(int cpu, bool enable);
-extern void imx_set_cpu_jump(int cpu, void *jump_addr);
 extern void imx_src_init(void);
 extern void imx_src_prepare_restart(void);
 extern void imx_gpc_init(void);

arch/arm/mach-imx/cpu_op-mx51.c

···
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/bug.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-
-#include "hardware.h"
-
-static struct cpu_op mx51_cpu_op[] = {
-	{
-	.cpu_rate = 160000000,},
-	{
-	.cpu_rate = 800000000,},
-};
-
-struct cpu_op *mx51_get_cpu_op(int *op)
-{
-	*op = ARRAY_SIZE(mx51_cpu_op);
-	return mx51_cpu_op;
-}

arch/arm/mach-imx/cpu_op-mx51.h

···
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-extern struct cpu_op *mx51_get_cpu_op(int *op);

arch/arm/mach-imx/cpufreq.c

···
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/*
- * A driver for the Freescale Semiconductor i.MXC CPUfreq module.
- * The CPUFREQ driver is for controlling CPU frequency. It allows you to change
- * the CPU clock speed on the fly.
- */
-
-#include <linux/module.h>
-#include <linux/cpufreq.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-
-#include "hardware.h"
-
-#define CLK32_FREQ	32768
-#define NANOSECOND	(1000 * 1000 * 1000)
-
-struct cpu_op *(*get_cpu_op)(int *op);
-
-static int cpu_freq_khz_min;
-static int cpu_freq_khz_max;
-
-static struct clk *cpu_clk;
-static struct cpufreq_frequency_table *imx_freq_table;
-
-static int cpu_op_nr;
-static struct cpu_op *cpu_op_tbl;
-
-static int set_cpu_freq(int freq)
-{
-	int ret = 0;
-	int org_cpu_rate;
-
-	org_cpu_rate = clk_get_rate(cpu_clk);
-	if (org_cpu_rate == freq)
-		return ret;
-
-	ret = clk_set_rate(cpu_clk, freq);
-	if (ret != 0) {
-		printk(KERN_DEBUG "cannot set CPU clock rate\n");
-		return ret;
-	}
-
-	return ret;
-}
-
-static int mxc_verify_speed(struct cpufreq_policy *policy)
-{
-	if (policy->cpu != 0)
-		return -EINVAL;
-
-	return cpufreq_frequency_table_verify(policy, imx_freq_table);
-}
-
-static unsigned int mxc_get_speed(unsigned int cpu)
-{
-	if (cpu)
-		return 0;
-
-	return clk_get_rate(cpu_clk) / 1000;
-}
-
-static int mxc_set_target(struct cpufreq_policy *policy,
-			  unsigned int target_freq, unsigned int relation)
-{
-	struct cpufreq_freqs freqs;
-	int freq_Hz;
-	int ret = 0;
-	unsigned int index;
-
-	cpufreq_frequency_table_target(policy, imx_freq_table,
-			target_freq, relation, &index);
-	freq_Hz = imx_freq_table[index].frequency * 1000;
-
-	freqs.old = clk_get_rate(cpu_clk) / 1000;
-	freqs.new = freq_Hz / 1000;
-	freqs.cpu = 0;
-	freqs.flags = 0;
-	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
-
-	ret = set_cpu_freq(freq_Hz);
-
-	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
-
-	return ret;
-}
-
-static int mxc_cpufreq_init(struct cpufreq_policy *policy)
-{
-	int ret;
-	int i;
-
-	printk(KERN_INFO "i.MXC CPU frequency driver\n");
-
-	if (policy->cpu != 0)
-		return -EINVAL;
-
-	if (!get_cpu_op)
-		return -EINVAL;
-
-	cpu_clk = clk_get(NULL, "cpu_clk");
-	if (IS_ERR(cpu_clk)) {
-		printk(KERN_ERR "%s: failed to get cpu clock\n", __func__);
-		return PTR_ERR(cpu_clk);
-	}
-
-	cpu_op_tbl = get_cpu_op(&cpu_op_nr);
-
-	cpu_freq_khz_min = cpu_op_tbl[0].cpu_rate / 1000;
-	cpu_freq_khz_max = cpu_op_tbl[0].cpu_rate / 1000;
-
-	imx_freq_table = kmalloc(
-		sizeof(struct cpufreq_frequency_table) * (cpu_op_nr + 1),
-			GFP_KERNEL);
-	if (!imx_freq_table) {
-		ret = -ENOMEM;
-		goto err1;
-	}
-
-	for (i = 0; i < cpu_op_nr; i++) {
-		imx_freq_table[i].index = i;
-		imx_freq_table[i].frequency = cpu_op_tbl[i].cpu_rate / 1000;
-
-		if ((cpu_op_tbl[i].cpu_rate / 1000) < cpu_freq_khz_min)
-			cpu_freq_khz_min = cpu_op_tbl[i].cpu_rate / 1000;
-
-		if ((cpu_op_tbl[i].cpu_rate / 1000) > cpu_freq_khz_max)
-			cpu_freq_khz_max = cpu_op_tbl[i].cpu_rate / 1000;
-	}
-
-	imx_freq_table[i].index = i;
-	imx_freq_table[i].frequency = CPUFREQ_TABLE_END;
-
-	policy->cur = clk_get_rate(cpu_clk) / 1000;
-	policy->min = policy->cpuinfo.min_freq = cpu_freq_khz_min;
-	policy->max = policy->cpuinfo.max_freq = cpu_freq_khz_max;
-
-	/* Manual states, that PLL stabilizes in two CLK32 periods */
-	policy->cpuinfo.transition_latency = 2 * NANOSECOND / CLK32_FREQ;
-
-	ret = cpufreq_frequency_table_cpuinfo(policy, imx_freq_table);
-
-	if (ret < 0) {
-		printk(KERN_ERR "%s: failed to register i.MXC CPUfreq with error code %d\n",
-		       __func__, ret);
-		goto err;
-	}
-
-	cpufreq_frequency_table_get_attr(imx_freq_table, policy->cpu);
-	return 0;
-err:
-	kfree(imx_freq_table);
-err1:
-	clk_put(cpu_clk);
-	return ret;
-}
-
-static int mxc_cpufreq_exit(struct cpufreq_policy *policy)
-{
-	cpufreq_frequency_table_put_attr(policy->cpu);
-
-	set_cpu_freq(cpu_freq_khz_max * 1000);
-	clk_put(cpu_clk);
-	kfree(imx_freq_table);
-	return 0;
-}
-
-static struct cpufreq_driver mxc_driver = {
-	.flags = CPUFREQ_STICKY,
-	.verify = mxc_verify_speed,
-	.target = mxc_set_target,
-	.get = mxc_get_speed,
-	.init = mxc_cpufreq_init,
-	.exit = mxc_cpufreq_exit,
-	.name = "imx",
-};
-
-static int mxc_cpufreq_driver_init(void)
-{
-	return cpufreq_register_driver(&mxc_driver);
-}
-
-static void mxc_cpufreq_driver_exit(void)
-{
-	cpufreq_unregister_driver(&mxc_driver);
-}
-
-module_init(mxc_cpufreq_driver_init);
-module_exit(mxc_cpufreq_driver_exit);
-
-MODULE_AUTHOR("Freescale Semiconductor Inc. Yong Shen <[e-mail]>");
-MODULE_DESCRIPTION("CPUfreq driver for i.MX");
-MODULE_LICENSE("GPL");

arch/arm/mach-imx/devices/Kconfig

···
 
 config IMX_HAVE_PLATFORM_SPI_IMX
 	bool
-
-config IMX_HAVE_PLATFORM_AHCI
-	bool
-	default y if ARCH_MX53

arch/arm/mach-imx/devices/Makefile

···
 obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) +=  platform-spi_imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_AHCI) +=  platform-ahci-imx.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_EMMA) += platform-mx2-emma.o

arch/arm/mach-imx/devices/devices-common.h

···
 					int irq, int irq_err);
 struct platform_device *imx_add_imx_sdma(char *name,
 	resource_size_t iobase, int irq, struct sdma_platform_data *pdata);
-
-#include <linux/ahci_platform.h>
-struct imx_ahci_imx_data {
-	const char *devid;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_ahci_imx(
-		const struct imx_ahci_imx_data *data,
-		const struct ahci_platform_data *pdata);

arch/arm/mach-imx/devices/platform-ahci-imx.c

···
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
-
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
-
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-#include <asm/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_ahci_imx_data_entry_single(soc, _devid)		\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _SATA_BASE_ADDR,			\
-		.irq = soc ## _INT_SATA,				\
-	}
-
-#ifdef CONFIG_SOC_IMX53
-const struct imx_ahci_imx_data imx53_ahci_imx_data __initconst =
-	imx_ahci_imx_data_entry_single(MX53, "imx53-ahci");
-#endif
-
-enum {
-	HOST_CAP = 0x00,
-	HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
-	HOST_PORTS_IMPL	= 0x0c,
-	HOST_TIMER1MS = 0xe0, /* Timer 1-ms */
-};
-
-static struct clk *sata_clk, *sata_ref_clk;
-
-/* AHCI module Initialization, if return 0, initialization is successful. */
-static int imx_sata_init(struct device *dev, void __iomem *addr)
-{
-	u32 tmpdata;
-	int ret = 0;
-	struct clk *clk;
-
-	sata_clk = clk_get(dev, "ahci");
-	if (IS_ERR(sata_clk)) {
-		dev_err(dev, "no sata clock.\n");
-		return PTR_ERR(sata_clk);
-	}
-	ret = clk_prepare_enable(sata_clk);
-	if (ret) {
-		dev_err(dev, "can't prepare/enable sata clock.\n");
-		goto put_sata_clk;
-	}
-
-	/* Get the AHCI SATA PHY CLK */
-	sata_ref_clk = clk_get(dev, "ahci_phy");
-	if (IS_ERR(sata_ref_clk)) {
-		dev_err(dev, "no sata ref clock.\n");
-		ret = PTR_ERR(sata_ref_clk);
-		goto release_sata_clk;
-	}
-	ret = clk_prepare_enable(sata_ref_clk);
-	if (ret) {
-		dev_err(dev, "can't prepare/enable sata ref clock.\n");
-		goto put_sata_ref_clk;
-	}
-
-	/* Get the AHB clock rate, and configure the TIMER1MS reg later */
-	clk = clk_get(dev, "ahci_dma");
-	if (IS_ERR(clk)) {
-		dev_err(dev, "no dma clock.\n");
-		ret = PTR_ERR(clk);
-		goto release_sata_ref_clk;
-	}
-	tmpdata = clk_get_rate(clk) / 1000;
-	clk_put(clk);
-
-	writel(tmpdata, addr + HOST_TIMER1MS);
-
-	tmpdata = readl(addr + HOST_CAP);
-	if (!(tmpdata & HOST_CAP_SSS)) {
-		tmpdata |= HOST_CAP_SSS;
-		writel(tmpdata, addr + HOST_CAP);
-	}
-
-	if (!(readl(addr + HOST_PORTS_IMPL) & 0x1))
-		writel((readl(addr + HOST_PORTS_IMPL) | 0x1),
-			addr + HOST_PORTS_IMPL);
-
-	return 0;
-
-release_sata_ref_clk:
-	clk_disable_unprepare(sata_ref_clk);
-put_sata_ref_clk:
-	clk_put(sata_ref_clk);
-release_sata_clk:
-	clk_disable_unprepare(sata_clk);
-put_sata_clk:
-	clk_put(sata_clk);
-
-	return ret;
-}
-
-static void imx_sata_exit(struct device *dev)
-{
-	clk_disable_unprepare(sata_ref_clk);
-	clk_put(sata_ref_clk);
-
-	clk_disable_unprepare(sata_clk);
-	clk_put(sata_clk);
-
-}
-struct platform_device *__init imx_add_ahci_imx(
-		const struct imx_ahci_imx_data *data,
-		const struct ahci_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_4K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device_dmamask(data->devid, 0,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata),  DMA_BIT_MASK(32));
-}
-
-struct platform_device *__init imx53_add_ahci_imx(void)
-{
-	struct ahci_platform_data pdata = {
-		.init = imx_sata_init,
-		.exit = imx_sata_exit,
-	};
-
-	return imx_add_ahci_imx(&imx53_ahci_imx_data, &pdata);
-}

arch/arm/mach-imx/hardware.h

···
 
 #include "mxc.h"
 
-#include "mx6q.h"
 #include "mx51.h"
 #include "mx53.h"
 #include "mx3x.h"

arch/arm/mach-imx/mach-cpuimx51sd.c

···
 
 #include "common.h"
 #include "devices-imx51.h"
-#include "cpu_op-mx51.h"
 #include "eukrea-baseboards.h"
 #include "hardware.h"
 #include "iomux-mx51.h"
···
 
 	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
 					ARRAY_SIZE(eukrea_cpuimx51sd_pads));
-
-#if defined(CONFIG_CPU_FREQ_IMX)
-	get_cpu_op = mx51_get_cpu_op;
-#endif
 
 	imx51_add_imx_uart(0, &uart_pdata);
 	imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);

arch/arm/mach-imx/mach-mx51_babbage.c

···
 
 #include "common.h"
 #include "devices-imx51.h"
-#include "cpu_op-mx51.h"
 #include "hardware.h"
 #include "iomux-mx51.h"
 
···
 
 	imx51_soc_init();
 
-#if defined(CONFIG_CPU_FREQ_IMX)
-	get_cpu_op = mx51_get_cpu_op;
-#endif
 	imx51_babbage_common_init();
 
 	imx51_add_imx_uart(0, &uart_pdata);

arch/arm/mach-imx/mx6q.h

···
-/*
- * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2011 Linaro Ltd.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#ifndef __MACH_MX6Q_H__
-#define __MACH_MX6Q_H__
-
-#define MX6Q_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX6Q_IO_ADDRESS(x)		IOMEM(MX6Q_IO_P2V(x))
-
-/*
- * The following are the blocks that need to be statically mapped.
- * For other blocks, the base address really should be retrieved from
- * device tree.
- */
-#define MX6Q_SCU_BASE_ADDR		0x00a00000
-#define MX6Q_SCU_SIZE			0x1000
-#define MX6Q_CCM_BASE_ADDR		0x020c4000
-#define MX6Q_CCM_SIZE			0x4000
-#define MX6Q_ANATOP_BASE_ADDR		0x020c8000
-#define MX6Q_ANATOP_SIZE		0x1000
-
-#endif	/* __MACH_MX6Q_H__ */