Merge tag 'ux500-dts-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

Some Ux500 DTS updates for v6.2:

- Some cleanups from Krzysztof for the SPI nodes.

- Fix up the NFC chip in Janice.

- Drop a bogus power domain regulator that isn't used for
the crypto blocks. (We use proper power domains now.)

- Add GPS to the Kyle.

* tag 'ux500-dts-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add GPS to the Kyle
ARM: dts: DBx500 cryp and hash uses power domain
ARM: dts: ux500: Fix up the Janice NFC chip
ARM: dts: ste: ux500: align SPI node name with dtschema

Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Arnd Bergmann <[e-mail]>

arch/arm/boot/dts/ste-dbx5x0.dtsi

···
 			compatible = "stericsson,ux500-cryp";
 			reg = <0xa03cb000 0x1000>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-
-			v-ape-supply = <&db8500_vape_reg>;
 			clocks = <&prcc_pclk 6 1>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		hash@a03c2000 {
 			compatible = "stericsson,ux500-hash";
 			reg = <0xa03c2000 0x1000>;
-
-			v-ape-supply = <&db8500_vape_reg>;
 			clocks = <&prcc_pclk 6 2>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 	};
 };

arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts

···
 		};
 	};
 
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/ste-ux500-samsung-codina.dts

···
 		};
 	};
 
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/ste-ux500-samsung-gavini.dts

···
 	/*
 	 * TODO: See if we can use the PL023 for this instead.
 	 */
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/ste-ux500-samsung-janice.dts

···
 	 * this derivative is 3wire support, so it cannot be used to drive
 	 * this panel interface. We have to use GPIO bit-banging instead.
 	 */
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220 */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
···
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		nfc@30 {
-			compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
-			reg = <0x30>;
+		/* This is only mounted on the GT-I9070P */
+		nfc@2b { /* 0x30? */
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
 			/* NFC IRQ on GPIO32 */
 			interrupt-parent = <&gpio1>;
 			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
···
 			/* GPIO88 */
 			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
-			pinctrl-0 = <&pn547_janice_default>;
+			pinctrl-0 = <&pn544_janice_default>;
 		};
 	};
 
···
 		};
 	};
 	nfc {
-		pn547_janice_default: pn547_janice {
+		pn544_janice_default: pn544_janice {
 			/* Interrupt line */
 			janice_cfg1 {
 				pins = "GPIO32_V2";

arch/arm/boot/dts/ste-ux500-samsung-kyle.dts

···
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
 			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_kyle_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
 		};
 
 		/* Debugging console UART connected to AB8505 USB */
···
 			kyle_cfg1 {
 				pins = "GPIO218_AH11";
 				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	g05ta03 {
+		g05ta03_kyle_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			kyle_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			kyle_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
 			};
 		};
 	};