Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:

- Add a new LED common module for ti-lmu driver family

- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property

- Add regulator support for LM36274 driver to lm363x-regulator.c

- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)

- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x

- Convert LED documentation to ReST

* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property

Documentation/devicetree/bindings/leds/leds-lm36274.txt

···
+* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias
+
+The LM36274 is an integrated four-channel WLED driver and LCD bias supply.
+The backlight boost provides the power to bias four parallel LED strings with
+up to 29V total output voltage. The 11-bit LED current is programmable via
+the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA.
+
+Parent device properties are documented in
+Documentation/devicetree/bindings/mfd/ti-lmu.txt
+
+Regulator properties are documented in
+Documentation/devicetree/bindings/regulator/lm363x-regulator.txt
+
+Required backlight properties:
+	- compatible:
+		"ti,lm36274-backlight"
+	- reg : 0
+	- #address-cells : 1
+	- #size-cells : 0
+	- led-sources : Indicates which LED strings will be enabled.
+			Values from 0-3, sources is 0 based so strings will be
+			source value + 1.
+
+Optional backlight properties:
+	- label : see Documentation/devicetree/bindings/leds/common.txt
+	- linux,default-trigger :
+	   see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is
+controlled by control bank B.
+
+lm36274@11 {
+	compatible = "ti,lm36274";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x11>;
+
+	enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm363x-regulator";
+
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <7150000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+	};
+
+	backlight {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm36274-backlight";
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 2>;
+			label = "white:backlight_cluster";
+			linux,default-trigger = "backlight";
+		};
+	};
+};
+
+For more product information please see the link below:
+http://www.ti.com/lit/ds/symlink/lm36274.pdf

Documentation/devicetree/bindings/leds/leds-lm3697.txt

···
+* Texas Instruments - LM3697 Highly Efficient White LED Driver
+
+The LM3697 11-bit LED driver provides high-
+performance backlight dimming for 1, 2, or 3 series
+LED strings while delivering up to 90% efficiency.
+
+This device is suitable for display and keypad lighting
+
+Required properties:
+	- compatible:
+		"ti,lm3697"
+	- reg :  I2C slave address
+	- #address-cells : 1
+	- #size-cells : 0
+
+Optional properties:
+	- enable-gpios : GPIO pin to enable/disable the device
+	- vled-supply : LED supply
+
+Required child properties:
+	- reg : 0 - LED is Controlled by bank A
+		1 - LED is Controlled by bank B
+	- led-sources : Indicates which HVLED string is associated to which
+			control bank.  This is a zero based property so
+			HVLED1 = 0, HVLED2 = 1, HVLED3 = 2.
+			Additional information is contained
+			in Documentation/devicetree/bindings/leds/common.txt
+
+Optional child properties:
+	- ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+	- ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+	- ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+	- label : see Documentation/devicetree/bindings/leds/common.txt
+	- linux,default-trigger :
+	   see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is
+controlled by control bank B.
+
+led-controller@36 {
+	compatible = "ti,lm3697";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x36>;
+
+	enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	vled-supply = <&vbatt>;
+
+	led@0 {
+		reg = <0>;
+		led-sources = <0 2>;
+		ti,brightness-resolution = <2047>;
+		ramp-up-us = <5000>;
+		ramp-down-us = <1000>;
+		label = "white:first_backlight_cluster";
+		linux,default-trigger = "backlight";
+	};
+
+	led@1 {
+		reg = <1>;
+		led-sources = <1>;
+		ti,brightness-resolution = <255>;
+		ramp-up-us = <500>;
+		ramp-down-us = <1000>;
+		label = "white:second_backlight_cluster";
+		linux,default-trigger = "backlight";
+	};
+}
+
+For more product information please see the link below:
+http://www.ti.com/lit/ds/symlink/lm3697.pdf

Documentation/devicetree/bindings/leds/leds-spi-byte.txt

···
+* Single Byte SPI LED Device Driver.
+
+The driver can be used for controllers with a very simple SPI protocol:
+- one LED is controlled by a single byte on MOSI
+- the value of the byte gives the brightness between two values (lowest to
+  highest)
+- no return value is necessary (no MISO signal)
+
+The value for lowest and highest brightness is dependent on the device and
+therefore on the compatible string.
+
+Depending on the compatible string some special functions (like hardware
+accelerated blinking) might can be supported too.
+
+The driver currently only supports one LED. The properties of the LED are
+configured in a sub-node in the device node.
+
+Required properties:
+- compatible: should be one of
+   * "ubnt,acb-spi-led"		microcontroller (SONiX 8F26E611LA) based device
+				used for example in Ubiquiti airCube ISP
+
+Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
+apply.
+
+LED sub-node properties:
+- label:
+	see Documentation/devicetree/bindings/leds/common.txt
+- default-state:
+	see Documentation/devicetree/bindings/leds/common.txt
+	Only "on" and "off" are supported.
+
+Example:
+
+led-controller@0 {
+	compatible = "ubnt,acb-spi-led";
+	reg = <0>;
+	spi-max-frequency = <100000>;
+
+	led {
+		label = "white:status";
+		default-state = "on";
+	};
+};

Documentation/devicetree/bindings/mfd/ti-lmu.txt

···
   LM3632       Backlight and regulator
   LM3633       Backlight, LED and fault monitor
   LM3695       Backlight
-  LM3697       Backlight and fault monitor
+  LM36274      Backlight and regulator
 
 Required properties:
   - compatible: Should be one of:
···
                 "ti,lm3632"
                 "ti,lm3633"
                 "ti,lm3695"
-                "ti,lm3697"
+		"ti,lm36274"
   - reg: I2C slave address.
          0x11 for LM3632
          0x29 for LM3631
-         0x36 for LM3633, LM3697
+         0x36 for LM3633
          0x63 for LM3695
+         0x11 for LM36274
 
-Optional property:
+Optional properties:
   - enable-gpios: A GPIO specifier for hardware enable pin.
+  - ramp-up-us: Current ramping from one brightness level to
+		the a higher brightness level.
+		Range from 2048 us - 117.44 s
+  - ramp-down-us: Current ramping from one brightness level to
+		  the a lower brightness level.
+		  Range from 2048 us - 117.44 s
+  - ti,brightness-resolution - This determines whether to use 8 bit brightness
+			       mode or 11 bit brightness mode.  If this value is
+			       not set the device is defaulted to the preferred
+			       8bit brightness mode per 7.3.4.1 of the data
+			       sheet.  This setting can either be in the parent
+			       node or as part of the LED child nodes.  This
+			       is determined by the part itself if the strings
+			       have a common brightness register or individual
+			       brightness registers.
+			       The values are 255 (8bit) or 2047 (11bit).
 
 Required node:
   - backlight: All LMU devices have backlight child nodes.
···
     Required properties:
       - compatible: Should be one of:
                     "ti,lm3633-fault-monitor"
-                    "ti,lm3697-fault-monitor"
   - leds: LED properties for LM3633. Please refer to [2].
+	  LED properties for LM36274. Please refer to [4].
   - regulators: Regulator properties for LM3631 and LM3632.
                 Please refer to [3].
 
 [1] ../leds/backlight/ti-lmu-backlight.txt
 [2] ../leds/leds-lm3633.txt
 [3] ../regulator/lm363x-regulator.txt
+[4] ../leds/leds-lm36274.txt
 
 lm3631@29 {
 	compatible = "ti,lm3631";
···
 
 		lcd_bl {
 			led-sources = <0 1>;
-			ramp-up-msec = <300>;
+			ramp-up-us = <300000>;
 		};
 	};
 };
···
 		main {
 			label = "main_lcd";
 			led-sources = <1 2>;
-			ramp-up-msec = <500>;
-			ramp-down-msec = <500>;
+			ramp-up-us = <500000>;
+			ramp-down-us = <500000>;
 		};
 
 		front {
 			label = "front_lcd";
 			led-sources = <0>;
-			ramp-up-msec = <1000>;
-			ramp-down-msec = <0>;
+			ramp-up-us = <1000000>;
+			ramp-down-us = <0>;
 		};
 	};
 
···
 	};
 };
 
-lm3697@36 {
-	compatible = "ti,lm3697";
-	reg = <0x36>;
+lm36274@11 {
+	compatible = "ti,lm36274";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x11>;
 
 	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm363x-regulator";
 
-	backlight {
-		compatible = "ti,lm3697-backlight";
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
 
-		lcd {
-			led-sources = <0 1 2>;
-			ramp-up-msec = <200>;
-			ramp-down-msec = <200>;
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <7150000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
 		};
 	};
 
-	fault-monitor {
-		compatible = "ti,lm3697-fault-monitor";
+	backlight {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm36274-backlight";
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 2>;
+			label = "white:backlight_cluster";
+			linux,default-trigger = "backlight";
+		};
 	};
 };

Documentation/laptops/thinkpad-acpi.txt

···
 sysfs notes:
 
 The ThinkLight sysfs interface is documented by the LED class
-documentation, in Documentation/leds/leds-class.txt.  The ThinkLight LED name
+documentation, in Documentation/leds/leds-class.rst.  The ThinkLight LED name
 is "tpacpi::thinklight".
 
 Due to limitations in the sysfs LED class, if the status of the ThinkLight
···
 sysfs notes:
 
 The ThinkPad LED sysfs interface is described in detail by the LED class
-documentation, in Documentation/leds/leds-class.txt.
+documentation, in Documentation/leds/leds-class.rst.
 
 The LEDs are named (in LED ID order, from 0 to 12):
 "tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt",

Documentation/leds/index.rst

···
+:orphan:
+
+====
+LEDs
+====
+
+.. toctree::
+   :maxdepth: 1
+
+   leds-class
+   leds-class-flash
+   ledtrig-oneshot
+   ledtrig-transient
+   ledtrig-usbport
+
+   uleds
+
+   leds-blinkm
+   leds-lm3556
+   leds-lp3944
+   leds-lp5521
+   leds-lp5523
+   leds-lp5562
+   leds-lp55xx
+   leds-mlxcpld

Documentation/leds/leds-blinkm.txt Documentation/leds/leds-blinkm.rst

···
+==================
+Leds BlinkM driver
+==================
+
 The leds-blinkm driver supports the devices of the BlinkM family.
 
 They are RGB-LED modules driven by a (AT)tiny microcontroller and
···
 a) LED class interface for use with triggers
 ############################################
 
-The registration follows the scheme:
-blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
+The registration follows the scheme::
 
-$ ls -h /sys/class/leds/blinkm-6-*
-/sys/class/leds/blinkm-6-9-blue:
-brightness  device  max_brightness  power  subsystem  trigger  uevent
+  blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
 
-/sys/class/leds/blinkm-6-9-green:
-brightness  device  max_brightness  power  subsystem  trigger  uevent
+  $ ls -h /sys/class/leds/blinkm-6-*
+  /sys/class/leds/blinkm-6-9-blue:
+  brightness  device  max_brightness  power  subsystem  trigger  uevent
 
-/sys/class/leds/blinkm-6-9-red:
-brightness  device  max_brightness  power  subsystem  trigger  uevent
+  /sys/class/leds/blinkm-6-9-green:
+  brightness  device  max_brightness  power  subsystem  trigger  uevent
+
+  /sys/class/leds/blinkm-6-9-red:
+  brightness  device  max_brightness  power  subsystem  trigger  uevent
 
 (same is /sys/bus/i2c/devices/6-0009/leds)
 
 We can control the colors separated into red, green and blue and
 assign triggers on each color.
 
-E.g.:
+E.g.::
 
-$ cat blinkm-6-9-blue/brightness
-05
+  $ cat blinkm-6-9-blue/brightness
+  05
 
-$ echo 200 > blinkm-6-9-blue/brightness
-$
+  $ echo 200 > blinkm-6-9-blue/brightness
+  $
 
-$ modprobe ledtrig-heartbeat
-$ echo heartbeat > blinkm-6-9-green/trigger
-$
+  $ modprobe ledtrig-heartbeat
+  $ echo heartbeat > blinkm-6-9-green/trigger
+  $
 
 
 b) Sysfs group to control rgb, fade, hsb, scripts ...
···
 in the sysfs folder of the I2C device.
 E.g. below /sys/bus/i2c/devices/6-0009/blinkm
 
-$ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
-blue  green  red  test
+  $ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
+  blue  green  red  test
 
 Currently supported is just setting red, green, blue
 and a test sequence.
 
-E.g.:
+E.g.::
 
-$ cat *
-00
-00
-00
-#Write into test to start test sequence!#
+  $ cat *
+  00
+  00
+  00
+  #Write into test to start test sequence!#
 
-$ echo 1 > test
-$
+  $ echo 1 > test
+  $
 
-$ echo 255 > red
-$
+  $ echo 255 > red
+  $
 
 
 
 as of 6/2012
 
 dl9pf <at> gmx <dot> de
-

Documentation/leds/leds-class-flash.txt Documentation/leds/leds-class-flash.rst

···
-
+==============================
 Flash LED handling under Linux
 ==============================
 
 Some LED devices provide two modes - torch and flash. In the LED subsystem
-those modes are supported by LED class (see Documentation/leds/leds-class.txt)
+those modes are supported by LED class (see Documentation/leds/leds-class.rst)
 and LED Flash class respectively. The torch mode related features are enabled
 by default and the flash ones only if a driver declares it by setting
 LED_DEV_CAP_FLASH flag.
···
 
 Following sysfs attributes are exposed for controlling flash LED devices:
 (see Documentation/ABI/testing/sysfs-class-led-flash)
+
 	- flash_brightness
 	- max_flash_brightness
 	- flash_timeout
···
 
 The driver must call the v4l2_flash_init function to get registered in the
 V4L2 subsystem. The function takes six arguments:
-- dev       : flash device, e.g. an I2C device
-- of_node   : of_node of the LED, may be NULL if the same as device's
-- fled_cdev : LED flash class device to wrap
-- iled_cdev : LED flash class device representing indicator LED associated with
-	      fled_cdev, may be NULL
-- ops : V4L2 specific ops
-	* external_strobe_set - defines the source of the flash LED strobe -
+
+- dev:
+	flash device, e.g. an I2C device
+- of_node:
+	of_node of the LED, may be NULL if the same as device's
+- fled_cdev:
+	LED flash class device to wrap
+- iled_cdev:
+	LED flash class device representing indicator LED associated with
+	fled_cdev, may be NULL
+- ops:
+	V4L2 specific ops
+
+	* external_strobe_set
+		defines the source of the flash LED strobe -
 		V4L2_CID_FLASH_STROBE control or external source, typically
 		a sensor, which makes it possible to synchronise the flash
 		strobe start with exposure start,
-	* intensity_to_led_brightness and led_brightness_to_intensity - perform
+	* intensity_to_led_brightness and led_brightness_to_intensity
+		perform
 		enum led_brightness <-> V4L2 intensity conversion in a device
 		specific manner - they can be used for devices with non-linear
 		LED current scale.
-- config : configuration for V4L2 Flash sub-device
-	* dev_name - the name of the media entity, unique in the system,
-	* flash_faults - bitmask of flash faults that the LED flash class
+- config:
+	configuration for V4L2 Flash sub-device
+
+	* dev_name
+		the name of the media entity, unique in the system,
+	* flash_faults
+		bitmask of flash faults that the LED flash class
 		device can report; corresponding LED_FAULT* bit definitions are
 		available in <linux/led-class-flash.h>,
-	* torch_intensity - constraints for the LED in TORCH mode
+	* torch_intensity
+		constraints for the LED in TORCH mode
 		in microamperes,
-	* indicator_intensity - constraints for the indicator LED
+	* indicator_intensity
+		constraints for the indicator LED
 		in microamperes,
-	* has_external_strobe - determines whether the flash strobe source
+	* has_external_strobe
+		determines whether the flash strobe source
 		can be switched to external,
 
 On remove the v4l2_flash_release function has to be called, which takes one

Documentation/leds/leds-class.txt Documentation/leds/leds-class.rst

···
-
+========================
 LED handling under Linux
 ========================
 
···
 
 Is currently of the form:
 
-"devicename:colour:function"
+	"devicename:colour:function"
 
 There have been calls for LED properties such as colour to be exported as
 individual led class attributes. As a solution which doesn't incur as much
···
 
 LED subsystem core exposes following API for setting brightness:
 
-    - led_set_brightness : it is guaranteed not to sleep, passing LED_OFF stops
+    - led_set_brightness:
+		it is guaranteed not to sleep, passing LED_OFF stops
 		blinking,
-    - led_set_brightness_sync : for use cases when immediate effect is desired -
+
+    - led_set_brightness_sync:
+		for use cases when immediate effect is desired -
 		it can block the caller for the time required for accessing
 		device registers and can sleep, passing LED_OFF stops hardware
 		blinking, returns -EBUSY if software blink fallback is enabled.
···
 
 A driver wanting to register a LED classdev for use by other drivers /
 userspace needs to allocate and fill a led_classdev struct and then call
-[devm_]led_classdev_register. If the non devm version is used the driver
+`[devm_]led_classdev_register`. If the non devm version is used the driver
 must call led_classdev_unregister from its remove function before
 free-ing the led_classdev struct.
 
···
 timers that may have been required for blinking.
 
 The blink_set() function should choose a user friendly blinking value
-if it is called with *delay_on==0 && *delay_off==0 parameters. In this
+if it is called with `*delay_on==0` && `*delay_off==0` parameters. In this
 case the driver should give back the chosen value through delay_on and
 delay_off parameters to the leds subsystem.
 

Documentation/leds/leds-lm3556.txt Documentation/leds/leds-lm3556.rst

···
+========================
 Kernel driver for lm3556
 ========================
 
-*Texas Instrument:
- 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
+* Texas Instrument:
+  1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
 * Datasheet: http://www.national.com/ds/LM/LM3556.pdf
 
 Authors:
-	Daniel Jeong
+      - Daniel Jeong
+
 	Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
 
 Description
 -----------
 There are 3 functions in LM3556, Flash, Torch and Indicator.
 
-FLASH MODE
+Flash Mode
+^^^^^^^^^^
+
 In Flash Mode, the LED current source(LED) provides 16 target current levels
 from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
 CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
 or by pulling the STROBE pin HIGH.
+
 LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
+
 * if STROBE pin is enabled, below example control brightness only, and
-ON / OFF will be controlled by STROBE pin.
+  ON / OFF will be controlled by STROBE pin.
 
 Flash Example:
-OFF     : #echo 0 > sys/class/leds/flash/brightness
-93.75 mA: #echo 1 > sys/class/leds/flash/brightness
-... .....
-1500  mA: #echo 16 > sys/class/leds/flash/brightness
 
-TORCH MODE
+OFF::
+
+	#echo 0 > sys/class/leds/flash/brightness
+
+93.75 mA::
+
+	#echo 1 > sys/class/leds/flash/brightness
+
+...
+
+1500  mA::
+
+	#echo 16 > sys/class/leds/flash/brightness
+
+Torch Mode
+^^^^^^^^^^
+
 In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
 REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
 hardware TORCH input.
+
 LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
 * if TORCH pin is enabled, below example control brightness only,
 and ON / OFF will be controlled by TORCH pin.
 
 Torch Example:
-OFF     : #echo 0 > sys/class/leds/torch/brightness
-46.88 mA: #echo 1 > sys/class/leds/torch/brightness
-... .....
-375 mA  : #echo 8 > sys/class/leds/torch/brightness
 
-INDICATOR MODE
+OFF::
+
+	#echo 0 > sys/class/leds/torch/brightness
+
+46.88 mA::
+
+	#echo 1 > sys/class/leds/torch/brightness
+
+...
+
+375 mA::
+
+	#echo 8 > sys/class/leds/torch/brightness
+
+Indicator Mode
+^^^^^^^^^^^^^^
+
 Indicator pattern can be set through sys/class/leds/indicator/pattern file,
 and 4 patterns are pre-defined in indicator_pattern array.
+
 According to N-lank, Pulse time and N Period values, different pattern wiill
 be generated.If you want new patterns for your own device, change
 indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
+
 Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
 
 Indicator pattern example:
-pattern 0: #echo 0 > sys/class/leds/indicator/pattern
-....
-pattern 3: #echo 3 > sys/class/leds/indicator/pattern
+
+pattern 0::
+
+	#echo 0 > sys/class/leds/indicator/pattern
+
+...
+
+pattern 3::
+
+	#echo 3 > sys/class/leds/indicator/pattern
 
 Indicator brightness can be controlled through
 sys/class/leds/indicator/brightness file.
 
 Example:
-OFF      : #echo 0 > sys/class/leds/indicator/brightness
-5.86 mA  : #echo 1 > sys/class/leds/indicator/brightness
-........
-46.875mA : #echo 8 > sys/class/leds/indicator/brightness
+
+OFF::
+
+	#echo 0 > sys/class/leds/indicator/brightness
+
+5.86 mA::
+
+	#echo 1 > sys/class/leds/indicator/brightness
+
+...
+
+46.875mA::
+
+	#echo 8 > sys/class/leds/indicator/brightness
 
 Notes
 -----
···
 To register the chip at address 0x63 on specific adapter, set the platform data
 according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
 
-Example:
+Example::
+
 	static struct i2c_board_info board_i2c_ch4[] __initdata = {
 		{
 			 I2C_BOARD_INFO(LM3556_NAME, 0x63),
···
 
 and register it in the platform init function
 
-Example:
+Example::
+
 	board_register_i2c_bus(4, 400,
 				board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));

Documentation/leds/leds-lp3944.txt Documentation/leds/leds-lp3944.rst

···
+====================
 Kernel driver lp3944
 ====================
 
   * National Semiconductor LP3944 Fun-light Chip
+
     Prefix: 'lp3944'
+
     Addresses scanned: None (see the Notes section below)
-    Datasheet: Publicly available at the National Semiconductor website
-               http://www.national.com/pf/LP/LP3944.html
+
+    Datasheet:
+
+	Publicly available at the National Semiconductor website
+	http://www.national.com/pf/LP/LP3944.html
 
 Authors:
-        Antonio Ospite <[e-mail]>
+	Antonio Ospite <[e-mail]>
 
 
 Description
···
 
 The DIM modes are used to set _blink_ patterns for leds, the pattern is
 specified supplying two parameters:
-  - period: from 0s to 1.6s
-  - duty cycle: percentage of the period the led is on, from 0 to 100
+
+  - period:
+	from 0s to 1.6s
+  - duty cycle:
+	percentage of the period the led is on, from 0 to 100
 
 Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
 See the datasheet for details.
···
 registered using the i2c_board_info mechanism.
 
 To register the chip at address 0x60 on adapter 0, set the platform data
-according to include/linux/leds-lp3944.h, set the i2c board info:
+according to include/linux/leds-lp3944.h, set the i2c board info::
 
 	static struct i2c_board_info a910_i2c_board_info[] __initdata = {
 		{
···
 		},
 	};
 
-and register it in the platform init function
+and register it in the platform init function::
 
 	i2c_register_board_info(0, a910_i2c_board_info,
 			ARRAY_SIZE(a910_i2c_board_info));

Documentation/leds/leds-lp5521.rst

···
+========================
+Kernel driver for lp5521
+========================
+
+* National Semiconductor LP5521 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5521.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+
+LP5521 can drive up to 3 channels. Leds can be controlled directly via
+the led class control interface. Channels have generic names:
+lp5521:channelx, where x is 0 .. 2
+
+All three channels can be also controlled using the engine micro programs.
+More details of the instructions can be found from the public data sheet.
+
+LP5521 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode and enginex_load
+   Control interface for the engines:
+
+   x is 1 .. 3
+
+   enginex_mode:
+	disabled, load, run
+   enginex_load:
+	store program (visible only in engine load mode)
+
+  Example (start to blink the channel 2 led)::
+
+	cd   /sys/class/leds/lp5521:channel2/device
+	echo "load" > engine3_mode
+	echo "037f4d0003ff6000" > engine3_load
+	echo "run" > engine3_mode
+
+  To stop the engine::
+
+	echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+sysfs contains a selftest entry.
+
+The test communicates with the chip and checks that
+the clock mode is automatically set to the requested one.
+
+Each channel has its own led current settings.
+
+- /sys/class/leds/lp5521:channel0/led_current - RW
+- /sys/class/leds/lp5521:channel0/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+example platform data::
+
+  static struct lp55xx_led_config lp5521_led_config[] = {
+	  {
+		.name = "red",
+		  .chan_nr        = 0,
+		  .led_current    = 50,
+		.max_current    = 130,
+	  }, {
+		.name = "green",
+		  .chan_nr        = 1,
+		  .led_current    = 0,
+		.max_current    = 130,
+	  }, {
+		.name = "blue",
+		  .chan_nr        = 2,
+		  .led_current    = 0,
+		.max_current    = 130,
+	  }
+  };
+
+  static int lp5521_setup(void)
+  {
+	/* setup HW resources */
+  }
+
+  static void lp5521_release(void)
+  {
+	/* Release HW resources */
+  }
+
+  static void lp5521_enable(bool state)
+  {
+	/* Control of chip enable signal */
+  }
+
+  static struct lp55xx_platform_data lp5521_platform_data = {
+	  .led_config     = lp5521_led_config,
+	  .num_channels   = ARRAY_SIZE(lp5521_led_config),
+	  .clock_mode     = LP55XX_CLOCK_EXT,
+	  .setup_resources   = lp5521_setup,
+	  .release_resources = lp5521_release,
+	  .enable            = lp5521_enable,
+  };
+
+Note:
+  chan_nr can have values between 0 and 2.
+  The name of each channel can be configurable.
+  If the name field is not defined, the default name will be set to 'xxxx:channelN'
+  (XXXX : pdata->label or i2c client name, N : channel number)
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.

Documentation/leds/leds-lp5521.txt

···
-Kernel driver for lp5521
-========================
-
-* National Semiconductor LP5521 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5521.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-
-LP5521 can drive up to 3 channels. Leds can be controlled directly via
-the led class control interface. Channels have generic names:
-lp5521:channelx, where x is 0 .. 2
-
-All three channels can be also controlled using the engine micro programs.
-More details of the instructions can be found from the public data sheet.
-
-LP5521 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode and enginex_load
-  Control interface for the engines:
-  x is 1 .. 3
-  enginex_mode : disabled, load, run
-  enginex_load : store program (visible only in engine load mode)
-
-  Example (start to blink the channel 2 led):
-  cd   /sys/class/leds/lp5521:channel2/device
-  echo "load" > engine3_mode
-  echo "037f4d0003ff6000" > engine3_load
-  echo "run" > engine3_mode
-
-  To stop the engine:
-  echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
-  For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-sysfs contains a selftest entry.
-The test communicates with the chip and checks that
-the clock mode is automatically set to the requested one.
-
-Each channel has its own led current settings.
-/sys/class/leds/lp5521:channel0/led_current - RW
-/sys/class/leds/lp5521:channel0/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-example platform data:
-
-Note: chan_nr can have values between 0 and 2.
-The name of each channel can be configurable.
-If the name field is not defined, the default name will be set to 'xxxx:channelN'
-(XXXX : pdata->label or i2c client name, N : channel number)
-
-static struct lp55xx_led_config lp5521_led_config[] = {
-        {
-		.name = "red",
-                .chan_nr        = 0,
-                .led_current    = 50,
-		.max_current    = 130,
-        }, {
-		.name = "green",
-                .chan_nr        = 1,
-                .led_current    = 0,
-		.max_current    = 130,
-        }, {
-		.name = "blue",
-                .chan_nr        = 2,
-                .led_current    = 0,
-		.max_current    = 130,
-        }
-};
-
-static int lp5521_setup(void)
-{
-	/* setup HW resources */
-}
-
-static void lp5521_release(void)
-{
-	/* Release HW resources */
-}
-
-static void lp5521_enable(bool state)
-{
-	/* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5521_platform_data = {
-        .led_config     = lp5521_led_config,
-        .num_channels   = ARRAY_SIZE(lp5521_led_config),
-        .clock_mode     = LP55XX_CLOCK_EXT,
-        .setup_resources   = lp5521_setup,
-        .release_resources = lp5521_release,
-        .enable            = lp5521_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.

Documentation/leds/leds-lp5523.rst

···
+========================
+Kernel driver for lp5523
+========================
+
+* National Semiconductor LP5523 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5523.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+LP5523 can drive up to 9 channels. Leds can be controlled directly via
+the led class control interface.
+The name of each channel is configurable in the platform data - name and label.
+There are three options to make the channel name.
+
+a) Define the 'name' in the platform data
+
+To make specific channel name, then use 'name' platform data.
+
+- /sys/class/leds/R1               (name: 'R1')
+- /sys/class/leds/B1               (name: 'B1')
+
+b) Use the 'label' with no 'name' field
+
+For one device name with channel number, then use 'label'.
+- /sys/class/leds/RGB:channelN     (label: 'RGB', N: 0 ~ 8)
+
+c) Default
+
+If both fields are NULL, 'lp5523' is used by default.
+- /sys/class/leds/lp5523:channelN  (N: 0 ~ 8)
+
+LP5523 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode, enginex_load and enginex_leds
+
+  Control interface for the engines:
+
+  x is 1 .. 3
+
+  enginex_mode:
+	disabled, load, run
+  enginex_load:
+	microcode load
+  enginex_leds:
+	led mux control
+
+  ::
+
+	cd /sys/class/leds/lp5523:channel2/device
+	echo "load" > engine3_mode
+	echo "9d80400004ff05ff437f0000" > engine3_load
+	echo "111111111" > engine3_leds
+	echo "run" > engine3_mode
+
+  To stop the engine::
+
+	echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+LP5523 has three master faders. If a channel is mapped to one of
+the master faders, its output is dimmed based on the value of the master
+fader.
+
+For example::
+
+  echo "123000123" > master_fader_leds
+
+creates the following channel-fader mappings::
+
+  channel 0,6 to master_fader1
+  channel 1,7 to master_fader2
+  channel 2,8 to master_fader3
+
+Then, to have 25% of the original output on channel 0,6::
+
+  echo 64 > master_fader1
+
+To have 0% of the original output (i.e. no output) channel 1,7::
+
+  echo 0 > master_fader2
+
+To have 100% of the original output (i.e. no dimming) on channel 2,8::
+
+  echo 255 > master_fader3
+
+To clear all master fader controls::
+
+  echo "000000000" > master_fader_leds
+
+Selftest uses always the current from the platform data.
+
+Each channel contains led current settings.
+- /sys/class/leds/lp5523:channel2/led_current - RW
+- /sys/class/leds/lp5523:channel2/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+Example platform data::
+
+	static struct lp55xx_led_config lp5523_led_config[] = {
+		{
+			.name		= "D1",
+			.chan_nr        = 0,
+			.led_current    = 50,
+			.max_current    = 130,
+		},
+	...
+		{
+			.chan_nr        = 8,
+			.led_current    = 50,
+			.max_current    = 130,
+		}
+	};
+
+	static int lp5523_setup(void)
+	{
+		/* Setup HW resources */
+	}
+
+	static void lp5523_release(void)
+	{
+		/* Release HW resources */
+	}
+
+	static void lp5523_enable(bool state)
+	{
+		/* Control chip enable signal */
+	}
+
+	static struct lp55xx_platform_data lp5523_platform_data = {
+		.led_config     = lp5523_led_config,
+		.num_channels   = ARRAY_SIZE(lp5523_led_config),
+		.clock_mode     = LP55XX_CLOCK_EXT,
+		.setup_resources   = lp5523_setup,
+		.release_resources = lp5523_release,
+		.enable            = lp5523_enable,
+	};
+
+Note
+  chan_nr can have values between 0 and 8.

Documentation/leds/leds-lp5523.txt

···
-Kernel driver for lp5523
-========================
-
-* National Semiconductor LP5523 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5523.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-LP5523 can drive up to 9 channels. Leds can be controlled directly via
-the led class control interface.
-The name of each channel is configurable in the platform data - name and label.
-There are three options to make the channel name.
-
-a) Define the 'name' in the platform data
-To make specific channel name, then use 'name' platform data.
-/sys/class/leds/R1               (name: 'R1')
-/sys/class/leds/B1               (name: 'B1')
-
-b) Use the 'label' with no 'name' field
-For one device name with channel number, then use 'label'.
-/sys/class/leds/RGB:channelN     (label: 'RGB', N: 0 ~ 8)
-
-c) Default
-If both fields are NULL, 'lp5523' is used by default.
-/sys/class/leds/lp5523:channelN  (N: 0 ~ 8)
-
-LP5523 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode, enginex_load and enginex_leds
-  Control interface for the engines:
-  x is 1 .. 3
-  enginex_mode : disabled, load, run
-  enginex_load : microcode load
-  enginex_leds : led mux control
-
-  cd /sys/class/leds/lp5523:channel2/device
-  echo "load" > engine3_mode
-  echo "9d80400004ff05ff437f0000" > engine3_load
-  echo "111111111" > engine3_leds
-  echo "run" > engine3_mode
-
-  To stop the engine:
-  echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
-  For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-LP5523 has three master faders. If a channel is mapped to one of
-the master faders, its output is dimmed based on the value of the master
-fader.
-
-For example,
-
-  echo "123000123" > master_fader_leds
-
-creates the following channel-fader mappings:
-
-  channel 0,6 to master_fader1
-  channel 1,7 to master_fader2
-  channel 2,8 to master_fader3
-
-Then, to have 25% of the original output on channel 0,6:
-
-  echo 64 > master_fader1
-
-To have 0% of the original output (i.e. no output) channel 1,7:
-
-  echo 0 > master_fader2
-
-To have 100% of the original output (i.e. no dimming) on channel 2,8:
-
-  echo 255 > master_fader3
-
-To clear all master fader controls:
-
-  echo "000000000" > master_fader_leds
-
-Selftest uses always the current from the platform data.
-
-Each channel contains led current settings.
-/sys/class/leds/lp5523:channel2/led_current - RW
-/sys/class/leds/lp5523:channel2/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-Example platform data:
-
-Note - chan_nr can have values between 0 and 8.
-
-static struct lp55xx_led_config lp5523_led_config[] = {
-        {
-		.name		= "D1",
-                .chan_nr        = 0,
-                .led_current    = 50,
-		.max_current    = 130,
-        },
-...
-        {
-                .chan_nr        = 8,
-                .led_current    = 50,
-		.max_current    = 130,
-        }
-};
-
-static int lp5523_setup(void)
-{
-	/* Setup HW resources */
-}
-
-static void lp5523_release(void)
-{
-	/* Release HW resources */
-}
-
-static void lp5523_enable(bool state)
-{
-	/* Control chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5523_platform_data = {
-        .led_config     = lp5523_led_config,
-        .num_channels   = ARRAY_SIZE(lp5523_led_config),
-        .clock_mode     = LP55XX_CLOCK_EXT,
-        .setup_resources   = lp5523_setup,
-        .release_resources = lp5523_release,
-        .enable            = lp5523_enable,
-};

Documentation/leds/leds-lp5562.rst

···
+========================
+Kernel driver for lp5562
+========================
+
+* TI LP5562 LED Driver
+
+Author: Milo(Woogyom) Kim <[e-mail]>
+
+Description
+===========
+
+  LP5562 can drive up to 4 channels. R/G/B and White.
+  LEDs can be controlled directly via the led class control interface.
+
+  All four channels can be also controlled using the engine micro programs.
+  LP5562 has the internal program memory for running various LED patterns.
+  For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+Device attribute
+================
+
+engine_mux
+  3 Engines are allocated in LP5562, but the number of channel is 4.
+  Therefore each channel should be mapped to the engine number.
+
+  Value: RGB or W
+
+  This attribute is used for programming LED data with the firmware interface.
+  Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
+  so additional sysfs is required
+
+  LED Map
+
+  ===== === ===============================
+  Red   ... Engine 1 (fixed)
+  Green ... Engine 2 (fixed)
+  Blue  ... Engine 3 (fixed)
+  White ... Engine 1 or 2 or 3 (selective)
+  ===== === ===============================
+
+How to load the program data using engine_mux
+=============================================
+
+  Before loading the LP5562 program data, engine_mux should be written between
+  the engine selection and loading the firmware.
+  Engine mux has two different mode, RGB and W.
+  RGB is used for loading RGB program data, W is used for W program data.
+
+  For example, run blinking green channel pattern::
+
+    echo 2 > /sys/bus/i2c/devices/xxxx/select_engine     # 2 is for green channel
+    echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux    # engine mux for RGB
+    echo 1 > /sys/class/firmware/lp5562/loading
+    echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+    echo 0 > /sys/class/firmware/lp5562/loading
+    echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+  To run a blinking white pattern::
+
+    echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
+    echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
+    echo 1 > /sys/class/firmware/lp5562/loading
+    echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+    echo 0 > /sys/class/firmware/lp5562/loading
+    echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+How to load the predefined patterns
+===================================
+
+  Please refer to 'leds-lp55xx.txt"
+
+Setting Current of Each Channel
+===============================
+
+  Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
+  The 'led_current' and 'max_current' are used.
+
+Example of Platform data
+========================
+
+::
+
+	static struct lp55xx_led_config lp5562_led_config[] = {
+		{
+			.name 		= "R",
+			.chan_nr	= 0,
+			.led_current	= 20,
+			.max_current	= 40,
+		},
+		{
+			.name 		= "G",
+			.chan_nr	= 1,
+			.led_current	= 20,
+			.max_current	= 40,
+		},
+		{
+			.name 		= "B",
+			.chan_nr	= 2,
+			.led_current	= 20,
+			.max_current	= 40,
+		},
+		{
+			.name 		= "W",
+			.chan_nr	= 3,
+			.led_current	= 20,
+			.max_current	= 40,
+		},
+	};
+
+	static int lp5562_setup(void)
+	{
+		/* setup HW resources */
+	}
+
+	static void lp5562_release(void)
+	{
+		/* Release HW resources */
+	}
+
+	static void lp5562_enable(bool state)
+	{
+		/* Control of chip enable signal */
+	}
+
+	static struct lp55xx_platform_data lp5562_platform_data = {
+		.led_config     = lp5562_led_config,
+		.num_channels   = ARRAY_SIZE(lp5562_led_config),
+		.setup_resources   = lp5562_setup,
+		.release_resources = lp5562_release,
+		.enable            = lp5562_enable,
+	};
+
+To configure the platform specific data, lp55xx_platform_data structure is used
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.

Documentation/leds/leds-lp5562.txt

···
-Kernel driver for LP5562
-========================
-
-* TI LP5562 LED Driver
-
-Author: Milo(Woogyom) Kim <[e-mail]>
-
-Description
-
-  LP5562 can drive up to 4 channels. R/G/B and White.
-  LEDs can be controlled directly via the led class control interface.
-
-  All four channels can be also controlled using the engine micro programs.
-  LP5562 has the internal program memory for running various LED patterns.
-  For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-Device attribute: engine_mux
-
-  3 Engines are allocated in LP5562, but the number of channel is 4.
-  Therefore each channel should be mapped to the engine number.
-  Value : RGB or W
-
-  This attribute is used for programming LED data with the firmware interface.
-  Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
-  so additional sysfs is required.
-
-  LED Map
-  Red   ... Engine 1 (fixed)
-  Green ... Engine 2 (fixed)
-  Blue  ... Engine 3 (fixed)
-  White ... Engine 1 or 2 or 3 (selective)
-
-How to load the program data using engine_mux
-
-  Before loading the LP5562 program data, engine_mux should be written between
-  the engine selection and loading the firmware.
-  Engine mux has two different mode, RGB and W.
-  RGB is used for loading RGB program data, W is used for W program data.
-
-  For example, run blinking green channel pattern,
-  echo 2 > /sys/bus/i2c/devices/xxxx/select_engine     # 2 is for green channel
-  echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux    # engine mux for RGB
-  echo 1 > /sys/class/firmware/lp5562/loading
-  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
-  echo 0 > /sys/class/firmware/lp5562/loading
-  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-  To run a blinking white pattern,
-  echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
-  echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
-  echo 1 > /sys/class/firmware/lp5562/loading
-  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
-  echo 0 > /sys/class/firmware/lp5562/loading
-  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-How to load the predefined patterns
-
-  Please refer to 'leds-lp55xx.txt"
-
-Setting Current of Each Channel
-
-  Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
-  The 'led_current' and 'max_current' are used.
-
-(Example of Platform data)
-
-To configure the platform specific data, lp55xx_platform_data structure is used.
-
-static struct lp55xx_led_config lp5562_led_config[] = {
-	{
-		.name 		= "R",
-		.chan_nr	= 0,
-		.led_current	= 20,
-		.max_current	= 40,
-	},
-	{
-		.name 		= "G",
-		.chan_nr	= 1,
-		.led_current	= 20,
-		.max_current	= 40,
-	},
-	{
-		.name 		= "B",
-		.chan_nr	= 2,
-		.led_current	= 20,
-		.max_current	= 40,
-	},
-	{
-		.name 		= "W",
-		.chan_nr	= 3,
-		.led_current	= 20,
-		.max_current	= 40,
-	},
-};
-
-static int lp5562_setup(void)
-{
-	/* setup HW resources */
-}
-
-static void lp5562_release(void)
-{
-	/* Release HW resources */
-}
-
-static void lp5562_enable(bool state)
-{
-	/* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5562_platform_data = {
-        .led_config     = lp5562_led_config,
-        .num_channels   = ARRAY_SIZE(lp5562_led_config),
-        .setup_resources   = lp5562_setup,
-        .release_resources = lp5562_release,
-        .enable            = lp5562_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.

Documentation/leds/leds-lp55xx.rst

···
+=================================================
+LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
+=================================================
+
+Authors: Milo(Woogyom) Kim <[e-mail]>
+
+Description
+-----------
+LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
+
+  Register access via the I2C
+  Device initialization/deinitialization
+  Create LED class devices for multiple output channels
+  Device attributes for user-space interface
+  Program memory for running LED patterns
+
+The LP55xx common driver provides these features using exported functions.
+
+  lp55xx_init_device() / lp55xx_deinit_device()
+  lp55xx_register_leds() / lp55xx_unregister_leds()
+  lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
+
+( Driver Structure Data )
+
+In lp55xx common driver, two different data structure is used.
+
+* lp55xx_led
+    control multi output LED channels such as led current, channel index.
+* lp55xx_chip
+    general chip control such like the I2C and platform data.
+
+For example, LP5521 has maximum 3 LED channels.
+LP5523/55231 has 9 output channels::
+
+  lp55xx_chip for LP5521 ... lp55xx_led #1
+			     lp55xx_led #2
+			     lp55xx_led #3
+
+  lp55xx_chip for LP5523 ... lp55xx_led #1
+			     lp55xx_led #2
+				   .
+				   .
+			     lp55xx_led #9
+
+( Chip Dependent Code )
+
+To support device specific configurations, special structure
+'lpxx_device_config' is used.
+
+  - Maximum number of channels
+  - Reset command, chip enable command
+  - Chip specific initialization
+  - Brightness control register access
+  - Setting LED output current
+  - Program memory address access for running patterns
+  - Additional device specific attributes
+
+( Firmware Interface )
+
+LP55xx family devices have the internal program memory for running
+various LED patterns.
+
+This pattern data is saved as a file in the user-land or
+hex byte string is written into the memory through the I2C.
+
+LP55xx common driver supports the firmware interface.
+
+LP55xx chips have three program engines.
+
+To load and run the pattern, the programming sequence is following.
+
+  (1) Select an engine number (1/2/3)
+  (2) Mode change to load
+  (3) Write pattern data into selected area
+  (4) Mode change to run
+
+The LP55xx common driver provides simple interfaces as below.
+
+select_engine:
+	Select which engine is used for running program
+run_engine:
+	Start program which is loaded via the firmware interface
+firmware:
+	Load program data
+
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
+For example, run blinking pattern in engine #1 of LP5521::
+
+	echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+	echo 1 > /sys/class/firmware/lp5521/loading
+	echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+	echo 0 > /sys/class/firmware/lp5521/loading
+	echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+For example, run blinking pattern in engine #3 of LP55231
+
+Two LEDs are configured as pattern output channels::
+
+	echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+	echo 1 > /sys/class/firmware/lp55231/loading
+	echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
+	echo 0 > /sys/class/firmware/lp55231/loading
+	echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
+	echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+To start blinking patterns in engine #2 and #3 simultaneously::
+
+	for idx in 2 3
+	do
+	echo $idx > /sys/class/leds/red/device/select_engine
+	sleep 0.1
+	echo 1 > /sys/class/firmware/lp5521/loading
+	echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+	echo 0 > /sys/class/firmware/lp5521/loading
+	done
+	echo 1 > /sys/class/leds/red/device/run_engine
+
+Here is another example for LP5523.
+
+Full LED strings are selected by 'engine2_leds'::
+
+	echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+	echo 1 > /sys/class/firmware/lp5523/loading
+	echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
+	echo 0 > /sys/class/firmware/lp5523/loading
+	echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
+	echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+As soon as 'loading' is set to 0, registered callback is called.
+Inside the callback, the selected engine is loaded and memory is updated.
+To run programmed pattern, 'run_engine' attribute should be enabled.
+
+The pattern sequence of LP8501 is similar to LP5523.
+
+However pattern data is specific.
+
+Ex 1) Engine 1 is used::
+
+	echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+	echo 1 > /sys/class/firmware/lp8501/loading
+	echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+	echo 0 > /sys/class/firmware/lp8501/loading
+	echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+Ex 2) Engine 2 and 3 are used at the same time::
+
+	echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+	sleep 1
+	echo 1 > /sys/class/firmware/lp8501/loading
+	echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+	echo 0 > /sys/class/firmware/lp8501/loading
+	sleep 1
+	echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+	sleep 1
+	echo 1 > /sys/class/firmware/lp8501/loading
+	echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+	echo 0 > /sys/class/firmware/lp8501/loading
+	sleep 1
+	echo 1 > /sys/class/leds/d1/device/run_engine
+
+( 'run_engine' and 'firmware_cb' )
+
+The sequence of running the program data is common.
+
+But each device has own specific register addresses for commands.
+
+To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
+
+run_engine:
+	Control the selected engine
+firmware_cb:
+	The callback function after loading the firmware is done.
+
+	Chip specific commands for loading and updating program memory.
+
+( Predefined pattern data )
+
+Without the firmware interface, LP55xx driver provides another method for
+loading a LED pattern. That is 'predefined' pattern.
+
+A predefined pattern is defined in the platform data and load it(or them)
+via the sysfs if needed.
+
+To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
+configured.
+
+Example of predefined pattern data::
+
+  /* mode_1: blinking data */
+  static const u8 mode_1[] = {
+		0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
+		};
+
+  /* mode_2: always on */
+  static const u8 mode_2[] = { 0x40, 0xFF, };
+
+  struct lp55xx_predef_pattern board_led_patterns[] = {
+	{
+		.r = mode_1,
+		.size_r = ARRAY_SIZE(mode_1),
+	},
+	{
+		.b = mode_2,
+		.size_b = ARRAY_SIZE(mode_2),
+	},
+  }
+
+  struct lp55xx_platform_data lp5562_pdata = {
+  ...
+	.patterns      = board_led_patterns,
+	.num_patterns  = ARRAY_SIZE(board_led_patterns),
+  };
+
+Then, mode_1 and mode_2 can be run via through the sysfs::
+
+  echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern    # red blinking LED pattern
+  echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern    # blue LED always on
+
+To stop running pattern::
+
+  echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern

Documentation/leds/leds-lp55xx.txt

···
-LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
-=================================================
-
-Authors: Milo(Woogyom) Kim <[e-mail]>
-
-Description
------------
-LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
-
-  Register access via the I2C
-  Device initialization/deinitialization
-  Create LED class devices for multiple output channels
-  Device attributes for user-space interface
-  Program memory for running LED patterns
-
-The LP55xx common driver provides these features using exported functions.
-  lp55xx_init_device() / lp55xx_deinit_device()
-  lp55xx_register_leds() / lp55xx_unregister_leds()
-  lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
-
-( Driver Structure Data )
-
-In lp55xx common driver, two different data structure is used.
-
-o lp55xx_led
-  control multi output LED channels such as led current, channel index.
-o lp55xx_chip
-  general chip control such like the I2C and platform data.
-
-For example, LP5521 has maximum 3 LED channels.
-LP5523/55231 has 9 output channels.
-
-lp55xx_chip for LP5521 ... lp55xx_led #1
-                           lp55xx_led #2
-                           lp55xx_led #3
-
-lp55xx_chip for LP5523 ... lp55xx_led #1
-                           lp55xx_led #2
-                                 .
-                                 .
-                           lp55xx_led #9
-
-( Chip Dependent Code )
-
-To support device specific configurations, special structure
-'lpxx_device_config' is used.
-
-  Maximum number of channels
-  Reset command, chip enable command
-  Chip specific initialization
-  Brightness control register access
-  Setting LED output current
-  Program memory address access for running patterns
-  Additional device specific attributes
-
-( Firmware Interface )
-
-LP55xx family devices have the internal program memory for running
-various LED patterns.
-This pattern data is saved as a file in the user-land or
-hex byte string is written into the memory through the I2C.
-LP55xx common driver supports the firmware interface.
-
-LP55xx chips have three program engines.
-To load and run the pattern, the programming sequence is following.
-  (1) Select an engine number (1/2/3)
-  (2) Mode change to load
-  (3) Write pattern data into selected area
-  (4) Mode change to run
-
-The LP55xx common driver provides simple interfaces as below.
-select_engine : Select which engine is used for running program
-run_engine    : Start program which is loaded via the firmware interface
-firmware      : Load program data
-
-In case of LP5523, one more command is required, 'enginex_leds'.
-It is used for selecting LED output(s) at each engine number.
-In more details, please refer to 'leds-lp5523.txt'.
-
-For example, run blinking pattern in engine #1 of LP5521
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5521/loading
-echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
-echo 0 > /sys/class/firmware/lp5521/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-For example, run blinking pattern in engine #3 of LP55231
-Two LEDs are configured as pattern output channels.
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp55231/loading
-echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
-echo 0 > /sys/class/firmware/lp55231/loading
-echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-To start blinking patterns in engine #2 and #3 simultaneously,
-for idx in 2 3
-do
-  echo $idx > /sys/class/leds/red/device/select_engine
-  sleep 0.1
-  echo 1 > /sys/class/firmware/lp5521/loading
-  echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
-  echo 0 > /sys/class/firmware/lp5521/loading
-done
-echo 1 > /sys/class/leds/red/device/run_engine
-
-Here is another example for LP5523.
-Full LED strings are selected by 'engine2_leds'.
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5523/loading
-echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
-echo 0 > /sys/class/firmware/lp5523/loading
-echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-As soon as 'loading' is set to 0, registered callback is called.
-Inside the callback, the selected engine is loaded and memory is updated.
-To run programmed pattern, 'run_engine' attribute should be enabled.
-
-The pattern sequence of LP8501 is similar to LP5523.
-However pattern data is specific.
-Ex 1) Engine 1 is used
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-Ex 2) Engine 2 and 3 are used at the same time
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 1 > /sys/class/leds/d1/device/run_engine
-
-( 'run_engine' and 'firmware_cb' )
-The sequence of running the program data is common.
-But each device has own specific register addresses for commands.
-To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
-run_engine  : Control the selected engine
-firmware_cb : The callback function after loading the firmware is done.
-              Chip specific commands for loading and updating program memory.
-
-( Predefined pattern data )
-
-Without the firmware interface, LP55xx driver provides another method for
-loading a LED pattern. That is 'predefined' pattern.
-A predefined pattern is defined in the platform data and load it(or them)
-via the sysfs if needed.
-To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
-configured.
-
-  Example of predefined pattern data:
-
-  /* mode_1: blinking data */
-  static const u8 mode_1[] = {
-		0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
-		};
-
-  /* mode_2: always on */
-  static const u8 mode_2[] = { 0x40, 0xFF, };
-
-  struct lp55xx_predef_pattern board_led_patterns[] = {
-	{
-		.r = mode_1,
-		.size_r = ARRAY_SIZE(mode_1),
-	},
-	{
-		.b = mode_2,
-		.size_b = ARRAY_SIZE(mode_2),
-	},
-  }
-
-  struct lp55xx_platform_data lp5562_pdata = {
-  ...
-	.patterns      = board_led_patterns,
-	.num_patterns  = ARRAY_SIZE(board_led_patterns),
-  };
-
-Then, mode_1 and mode_2 can be run via through the sysfs.
-
-  echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern    # red blinking LED pattern
-  echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern    # blue LED always on
-
-To stop running pattern,
-  echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern

Documentation/leds/leds-mlxcpld.rst

···
+=======================================
+Kernel driver for Mellanox systems LEDs
+=======================================
+
+Provide system LED support for the nex Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+"msn2410", "msb7800", "msn2740", "msn2100".
+
+Description
+-----------
+Driver provides the following LEDs for the systems "msx6710", "msx6720",
+"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
+
+  - mlxcpld:fan1:green
+  - mlxcpld:fan1:red
+  - mlxcpld:fan2:green
+  - mlxcpld:fan2:red
+  - mlxcpld:fan3:green
+  - mlxcpld:fan3:red
+  - mlxcpld:fan4:green
+  - mlxcpld:fan4:red
+  - mlxcpld:psu:green
+  - mlxcpld:psu:red
+  - mlxcpld:status:green
+  - mlxcpld:status:red
+
+ "status"
+  - CPLD reg offset: 0x20
+  - Bits [3:0]
+
+ "psu"
+  - CPLD reg offset: 0x20
+  - Bits [7:4]
+
+ "fan1"
+  - CPLD reg offset: 0x21
+  - Bits [3:0]
+
+ "fan2"
+  - CPLD reg offset: 0x21
+  - Bits [7:4]
+
+ "fan3"
+  - CPLD reg offset: 0x22
+  - Bits [3:0]
+
+ "fan4"
+  - CPLD reg offset: 0x22
+  - Bits [7:4]
+
+ Color mask for all the above LEDs:
+
+  [bit3,bit2,bit1,bit0] or
+  [bit7,bit6,bit5,bit4]:
+
+	- [0,0,0,0] = LED OFF
+	- [0,1,0,1] = Red static ON
+	- [1,1,0,1] = Green static ON
+	- [0,1,1,0] = Red blink 3Hz
+	- [1,1,1,0] = Green blink 3Hz
+	- [0,1,1,1] = Red blink 6Hz
+	- [1,1,1,1] = Green blink 6Hz
+
+Driver provides the following LEDs for the system "msn2100":
+
+  - mlxcpld:fan:green
+  - mlxcpld:fan:red
+  - mlxcpld:psu1:green
+  - mlxcpld:psu1:red
+  - mlxcpld:psu2:green
+  - mlxcpld:psu2:red
+  - mlxcpld:status:green
+  - mlxcpld:status:red
+  - mlxcpld:uid:blue
+
+ "status"
+  - CPLD reg offset: 0x20
+  - Bits [3:0]
+
+ "fan"
+  - CPLD reg offset: 0x21
+  - Bits [3:0]
+
+ "psu1"
+  - CPLD reg offset: 0x23
+  - Bits [3:0]
+
+ "psu2"
+  - CPLD reg offset: 0x23
+  - Bits [7:4]
+
+ "uid"
+  - CPLD reg offset: 0x24
+  - Bits [3:0]
+
+ Color mask for all the above LEDs, excepted uid:
+
+  [bit3,bit2,bit1,bit0] or
+  [bit7,bit6,bit5,bit4]:
+
+	- [0,0,0,0] = LED OFF
+	- [0,1,0,1] = Red static ON
+	- [1,1,0,1] = Green static ON
+	- [0,1,1,0] = Red blink 3Hz
+	- [1,1,1,0] = Green blink 3Hz
+	- [0,1,1,1] = Red blink 6Hz
+	- [1,1,1,1] = Green blink 6Hz
+
+ Color mask for uid LED:
+  [bit3,bit2,bit1,bit0]:
+
+	- [0,0,0,0] = LED OFF
+	- [1,1,0,1] = Blue static ON
+	- [1,1,1,0] = Blue blink 3Hz
+	- [1,1,1,1] = Blue blink 6Hz
+
+Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
+For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.

Documentation/leds/leds-mlxcpld.txt

···
-Kernel driver for Mellanox systems LEDs
-=======================================
-
-Provide system LED support for the nex Mellanox systems:
-"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
-"msn2410", "msb7800", "msn2740", "msn2100".
-
-Description
------------
-Driver provides the following LEDs for the systems "msx6710", "msx6720",
-"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
-  mlxcpld:fan1:green
-  mlxcpld:fan1:red
-  mlxcpld:fan2:green
-  mlxcpld:fan2:red
-  mlxcpld:fan3:green
-  mlxcpld:fan3:red
-  mlxcpld:fan4:green
-  mlxcpld:fan4:red
-  mlxcpld:psu:green
-  mlxcpld:psu:red
-  mlxcpld:status:green
-  mlxcpld:status:red
-
- "status"
-  CPLD reg offset: 0x20
-  Bits [3:0]
-
- "psu"
-  CPLD reg offset: 0x20
-  Bits [7:4]
-
- "fan1"
-  CPLD reg offset: 0x21
-  Bits [3:0]
-
- "fan2"
-  CPLD reg offset: 0x21
-  Bits [7:4]
-
- "fan3"
-  CPLD reg offset: 0x22
-  Bits [3:0]
-
- "fan4"
-  CPLD reg offset: 0x22
-  Bits [7:4]
-
- Color mask for all the above LEDs:
-  [bit3,bit2,bit1,bit0] or
-  [bit7,bit6,bit5,bit4]:
-	[0,0,0,0] = LED OFF
-	[0,1,0,1] = Red static ON
-	[1,1,0,1] = Green static ON
-	[0,1,1,0] = Red blink 3Hz
-	[1,1,1,0] = Green blink 3Hz
-	[0,1,1,1] = Red blink 6Hz
-	[1,1,1,1] = Green blink 6Hz
-
-Driver provides the following LEDs for the system "msn2100":
-  mlxcpld:fan:green
-  mlxcpld:fan:red
-  mlxcpld:psu1:green
-  mlxcpld:psu1:red
-  mlxcpld:psu2:green
-  mlxcpld:psu2:red
-  mlxcpld:status:green
-  mlxcpld:status:red
-  mlxcpld:uid:blue
-
- "status"
-  CPLD reg offset: 0x20
-  Bits [3:0]
-
- "fan"
-  CPLD reg offset: 0x21
-  Bits [3:0]
-
- "psu1"
-  CPLD reg offset: 0x23
-  Bits [3:0]
-
- "psu2"
-  CPLD reg offset: 0x23
-  Bits [7:4]
-
- "uid"
-  CPLD reg offset: 0x24
-  Bits [3:0]
-
- Color mask for all the above LEDs, excepted uid:
-  [bit3,bit2,bit1,bit0] or
-  [bit7,bit6,bit5,bit4]:
-	[0,0,0,0] = LED OFF
-	[0,1,0,1] = Red static ON
-	[1,1,0,1] = Green static ON
-	[0,1,1,0] = Red blink 3Hz
-	[1,1,1,0] = Green blink 3Hz
-	[0,1,1,1] = Red blink 6Hz
-	[1,1,1,1] = Green blink 6Hz
-
- Color mask for uid LED:
-  [bit3,bit2,bit1,bit0]:
-	[0,0,0,0] = LED OFF
-	[1,1,0,1] = Blue static ON
-	[1,1,1,0] = Blue blink 3Hz
-	[1,1,1,1] = Blue blink 6Hz
-
-Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
-For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.

Documentation/leds/ledtrig-oneshot.txt Documentation/leds/ledtrig-oneshot.rst

···
+====================
 One-shot LED Trigger
 ====================
 
···
 on (inverted) when not rearmed.
 
 The trigger can be activated from user space on led class devices as shown
-below:
+below::
 
   echo oneshot > trigger
 
 This adds sysfs attributes to the LED that are documented in:
 Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
 
-Example use-case: network devices, initialization:
+Example use-case: network devices, initialization::
 
   echo oneshot > trigger # set trigger for this led
   echo 33 > delay_on     # blink at 1 / (33 + 33) Hz on continuous traffic
   echo 33 > delay_off
 
-interface goes up:
+interface goes up::
 
   echo 1 > invert # set led as normally-on, turn the led on
 
-packet received/transmitted:
+packet received/transmitted::
 
   echo 1 > shot # led starts blinking, ignored if already blinking
 
-interface goes down
+interface goes down::
 
   echo 0 > invert # set led as normally-off, turn the led off

Documentation/leds/ledtrig-transient.txt Documentation/leds/ledtrig-transient.rst

···
+=====================
 LED Transient Trigger
 =====================
 
···
 state, the LED state changes to LED_OFF.
 
 Transient trigger can be enabled and disabled from user space on led class
-devices, that support this trigger as shown below:
+devices, that support this trigger as shown below::
 
-echo transient > trigger
-echo none > trigger
+	echo transient > trigger
+	echo none > trigger
 
-NOTE: Add a new property trigger state to control the state.
+NOTE:
+	Add a new property trigger state to control the state.
 
 This trigger exports three properties, activate, state, and duration. When
 transient trigger is activated these properties are set to default values.
···
 - state allows user to specify a transient state to be held for the specified
   duration.
 
-	activate - one shot timer activate mechanism.
+	activate
+	      - one shot timer activate mechanism.
 		1 when activated, 0 when deactivated.
 		default value is zero when transient trigger is enabled,
 		to allow duration to be set.
···
 		deactivated state indicates that there is no active timer
 		running.
 
-	duration - one shot timer value. When activate is set, duration value
+	duration
+	      - one shot timer value. When activate is set, duration value
 		is used to start a timer that runs once. This value doesn't
 		get changed by the trigger unless user does a set via
 		echo new_value > duration
 
-	state - transient state to be held. It has two values 0 or 1. 0 maps
+	state
+	      - transient state to be held. It has two values 0 or 1. 0 maps
 		to LED_OFF and 1 maps to LED_FULL. The specified state is
 		held for the duration of the one shot timer and then the
 		state gets changed to the non-transient state which is the
···
 at the set value to be used when activate is set at a future time. This will
 allow user app to set the time once and activate it to run it once for the
 specified value as needed. When timer expires, state is restored to the
-non-transient state which is the inverse of the transient state.
+non-transient state which is the inverse of the transient state:
 
-	echo 1 > activate - starts timer = duration when duration is not 0.
-	echo 0 > activate - cancels currently running timer.
-	echo n > duration - stores timer value to be used upon next
-                            activate. Currently active timer if
-                            any, continues to run for the specified time.
-	echo 0 > duration - stores timer value to be used upon next
-                            activate. Currently active timer if any,
-                            continues to run for the specified time.
-	echo 1 > state    - stores desired transient state LED_FULL to be
+	=================   ===============================================
+	echo 1 > activate   starts timer = duration when duration is not 0.
+	echo 0 > activate   cancels currently running timer.
+	echo n > duration   stores timer value to be used upon next
+			    activate. Currently active timer if
+			    any, continues to run for the specified time.
+	echo 0 > duration   stores timer value to be used upon next
+			    activate. Currently active timer if any,
+			    continues to run for the specified time.
+	echo 1 > state      stores desired transient state LED_FULL to be
 			    held for the specified duration.
-	echo 0 > state    - stores desired transient state LED_OFF to be
+	echo 0 > state      stores desired transient state LED_OFF to be
 			    held for the specified duration.
+	=================   ===============================================
 
-What is not supported:
-======================
+What is not supported
+=====================
+
 - Timer activation is one shot and extending and/or shortening the timer
   is not supported.
 
-Example use-case 1:
+Examples
+========
+
+use-case 1::
+
 	echo transient > trigger
 	echo n > duration
 	echo 1 > state
-repeat the following step as needed:
+
+repeat the following step as needed::
+
 	echo 1 > activate - start timer = duration to run once
 	echo 1 > activate - start timer = duration to run once
 	echo none > trigger
 
 This trigger is intended to be used for for the following example use cases:
+
  - Control of vibrate (phones, tablets etc.) hardware by user space app.
  - Use of LED by user space app as activity indicator.
  - Use of LED by user space app as a kind of watchdog indicator -- as
-       long as the app is alive, it can keep the LED illuminated, if it dies
-       the LED will be extinguished automatically.
+   long as the app is alive, it can keep the LED illuminated, if it dies
+   the LED will be extinguished automatically.
  - Use by any user space app that needs a transient GPIO output.

Documentation/leds/ledtrig-usbport.txt Documentation/leds/ledtrig-usbport.rst

···
+====================
 USB port LED trigger
 ====================
 
···
 echoing "1" to a chosen port.
 
 Please note that this trigger allows selecting multiple USB ports for a single
-LED. This can be useful in two cases:
+LED.
+
+This can be useful in two cases:
 
 1) Device with single USB LED and few physical ports
+====================================================
 
 In such a case LED will be turned on as long as there is at least one connected
 USB device.
 
 2) Device with a physical port handled by few controllers
+=========================================================
 
 Some devices may have one controller per PHY standard. E.g. USB 3.0 physical
 port may be handled by ohci-platform, ehci-platform and xhci-hcd. If there is
···
 
 
 This trigger can be activated from user space on led class devices as shown
-below:
+below::
 
   echo usbport > trigger
 
 This adds sysfs attributes to the LED that are documented in:
 Documentation/ABI/testing/sysfs-class-led-trigger-usbport
 
-Example use-case:
+Example use-case::
 
   echo usbport > trigger
   echo 1 > ports/usb1-port1

Documentation/leds/uleds.txt Documentation/leds/uleds.rst

···
+==============
 Userspace LEDs
 ==============
 
···
 
 When the driver is loaded, a character device is created at /dev/uleds. To
 create a new LED class device, open /dev/uleds and write a uleds_user_dev
-structure to it (found in kernel public header file linux/uleds.h).
+structure to it (found in kernel public header file linux/uleds.h)::
 
     #define LED_MAX_NAME_SIZE 64
 
     struct uleds_user_dev {
-        char name[LED_MAX_NAME_SIZE];
+	char name[LED_MAX_NAME_SIZE];
     };
 
 A new LED class device will be created with the name given. The name can be

MAINTAINERS

···
 S:	Supported
 F:	drivers/leds/leds-mlxcpld.c
 F:	drivers/leds/leds-mlxreg.c
-F:	Documentation/leds/leds-mlxcpld.txt
+F:	Documentation/leds/leds-mlxcpld.rst
 
 MELLANOX PLATFORM DRIVER
 M:	Vadim Pasternak <[e-mail]>

drivers/leds/Kconfig

···
 	  To compile this driver as a module, choose M here: the module
 	  will be called leds-nic78bx.
 
+config LEDS_SPI_BYTE
+	tristate "LED support for SPI LED controller with a single byte"
+	depends on LEDS_CLASS
+	depends on SPI
+	depends on OF
+	help
+	  This option enables support for LED controller which use a single byte
+	  for controlling the brightness. Currently the following controller is
+	  supported: Ubiquiti airCube ISP microcontroller based LED controller.
+
+config LEDS_TI_LMU_COMMON
+	tristate "LED driver for TI LMU"
+	depends on LEDS_CLASS
+	depends on REGMAP
+	help
+	  Say Y to enable the LED driver for TI LMU devices.
+	  This supports common features between the TI LM3532, LM3631, LM3632,
+	  LM3633, LM3695 and LM3697.
+
+config LEDS_LM3697
+	tristate "LED driver for LM3697"
+	depends on LEDS_TI_LMU_COMMON
+	depends on I2C && OF
+	help
+	  Say Y to enable the LM3697 LED driver for TI LMU devices.
+	  This supports the LED device LM3697.
+
+config LEDS_LM36274
+	tristate "LED driver for LM36274"
+	depends on LEDS_TI_LMU_COMMON
+	depends on MFD_TI_LMU
+	help
+	  Say Y to enable the LM36274 LED driver for TI LMU devices.
+	  This supports the LED device LM36274.
+
 comment "LED Triggers"
 source "drivers/leds/trigger/Kconfig"
 

drivers/leds/Makefile

···
 obj-$(CONFIG_LEDS_MLXCPLD)		+= leds-mlxcpld.o
 obj-$(CONFIG_LEDS_MLXREG)		+= leds-mlxreg.o
 obj-$(CONFIG_LEDS_NIC78BX)		+= leds-nic78bx.o
+obj-$(CONFIG_LEDS_SPI_BYTE)		+= leds-spi-byte.o
 obj-$(CONFIG_LEDS_MT6323)		+= leds-mt6323.o
 obj-$(CONFIG_LEDS_LM3692X)		+= leds-lm3692x.o
 obj-$(CONFIG_LEDS_SC27XX_BLTC)		+= leds-sc27xx-bltc.o
 obj-$(CONFIG_LEDS_LM3601X)		+= leds-lm3601x.o
+obj-$(CONFIG_LEDS_TI_LMU_COMMON)	+= leds-ti-lmu-common.o
+obj-$(CONFIG_LEDS_LM3697)		+= leds-lm3697.o
+obj-$(CONFIG_LEDS_LM36274)		+= leds-lm36274.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_CR0014114)		+= leds-cr0014114.o

drivers/leds/leds-lm36274.c

···
+// SPDX-License-Identifier: GPL-2.0
+// TI LM36274 LED chip family driver
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/leds.h>
+#include <linux/leds-ti-lmu-common.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/ti-lmu.h>
+#include <linux/mfd/ti-lmu-register.h>
+
+#include <uapi/linux/uleds.h>
+
+#define LM36274_MAX_STRINGS	4
+#define LM36274_BL_EN		BIT(4)
+
+/**
+ * struct lm36274
+ * @pdev: platform device
+ * @led_dev: led class device
+ * @lmu_data: Register and setting values for common code
+ * @regmap: Devices register map
+ * @dev: Pointer to the devices device struct
+ * @led_sources - The LED strings supported in this array
+ * @num_leds - Number of LED strings are supported in this array
+ */
+struct lm36274 {
+	struct platform_device *pdev;
+	struct led_classdev led_dev;
+	struct ti_lmu_bank lmu_data;
+	struct regmap *regmap;
+	struct device *dev;
+
+	u32 led_sources[LM36274_MAX_STRINGS];
+	int num_leds;
+};
+
+static int lm36274_brightness_set(struct led_classdev *led_cdev,
+				enum led_brightness brt_val)
+{
+	struct lm36274 *led = container_of(led_cdev, struct lm36274, led_dev);
+
+	return ti_lmu_common_set_brightness(&led->lmu_data, brt_val);
+}
+
+static int lm36274_init(struct lm36274 *lm36274_data)
+{
+	int enable_val = 0;
+	int i;
+
+	for (i = 0; i < lm36274_data->num_leds; i++)
+		enable_val |= (1 << lm36274_data->led_sources[i]);
+
+	if (!enable_val) {
+		dev_err(lm36274_data->dev, "No LEDs were enabled\n");
+		return -EINVAL;
+	}
+
+	enable_val |= LM36274_BL_EN;
+
+	return regmap_write(lm36274_data->regmap, LM36274_REG_BL_EN,
+			    enable_val);
+}
+
+static int lm36274_parse_dt(struct lm36274 *lm36274_data)
+{
+	struct fwnode_handle *child = NULL;
+	char label[LED_MAX_NAME_SIZE];
+	struct device *dev = &lm36274_data->pdev->dev;
+	const char *name;
+	int child_cnt;
+	int ret = -EINVAL;
+
+	/* There should only be 1 node */
+	child_cnt = device_get_child_node_count(dev);
+	if (child_cnt != 1)
+		return -EINVAL;
+
+	device_for_each_child_node(dev, child) {
+		ret = fwnode_property_read_string(child, "label", &name);
+		if (ret)
+			snprintf(label, sizeof(label),
+				"%s::", lm36274_data->pdev->name);
+		else
+			snprintf(label, sizeof(label),
+				 "%s:%s", lm36274_data->pdev->name, name);
+
+		lm36274_data->num_leds = fwnode_property_read_u32_array(child,
+							  "led-sources",
+							  NULL, 0);
+		if (lm36274_data->num_leds <= 0)
+			return -ENODEV;
+
+		ret = fwnode_property_read_u32_array(child, "led-sources",
+						     lm36274_data->led_sources,
+						     lm36274_data->num_leds);
+		if (ret) {
+			dev_err(dev, "led-sources property missing\n");
+			return ret;
+		}
+
+		fwnode_property_read_string(child, "linux,default-trigger",
+					&lm36274_data->led_dev.default_trigger);
+
+	}
+
+	lm36274_data->lmu_data.regmap = lm36274_data->regmap;
+	lm36274_data->lmu_data.max_brightness = MAX_BRIGHTNESS_11BIT;
+	lm36274_data->lmu_data.msb_brightness_reg = LM36274_REG_BRT_MSB;
+	lm36274_data->lmu_data.lsb_brightness_reg = LM36274_REG_BRT_LSB;
+
+	lm36274_data->led_dev.name = label;
+	lm36274_data->led_dev.max_brightness = MAX_BRIGHTNESS_11BIT;
+	lm36274_data->led_dev.brightness_set_blocking = lm36274_brightness_set;
+
+	return 0;
+}
+
+static int lm36274_probe(struct platform_device *pdev)
+{
+	struct ti_lmu *lmu = dev_get_drvdata(pdev->dev.parent);
+	struct lm36274 *lm36274_data;
+	int ret;
+
+	lm36274_data = devm_kzalloc(&pdev->dev, sizeof(*lm36274_data),
+				    GFP_KERNEL);
+	if (!lm36274_data)
+		return -ENOMEM;
+
+	lm36274_data->pdev = pdev;
+	lm36274_data->dev = lmu->dev;
+	lm36274_data->regmap = lmu->regmap;
+	dev_set_drvdata(&pdev->dev, lm36274_data);
+
+	ret = lm36274_parse_dt(lm36274_data);
+	if (ret) {
+		dev_err(lm36274_data->dev, "Failed to parse DT node\n");
+		return ret;
+	}
+
+	ret = lm36274_init(lm36274_data);
+	if (ret) {
+		dev_err(lm36274_data->dev, "Failed to init the device\n");
+		return ret;
+	}
+
+	return devm_led_classdev_register(lm36274_data->dev,
+					 &lm36274_data->led_dev);
+}
+
+static const struct of_device_id of_lm36274_leds_match[] = {
+	{ .compatible = "ti,lm36274-backlight", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lm36274_leds_match);
+
+static struct platform_driver lm36274_driver = {
+	.probe  = lm36274_probe,
+	.driver = {
+		.name = "lm36274-leds",
+	},
+};
+module_platform_driver(lm36274_driver)
+
+MODULE_DESCRIPTION("Texas Instruments LM36274 LED driver");
+MODULE_AUTHOR("Dan Murphy <[e-mail]>");
+MODULE_LICENSE("GPL v2");

drivers/leds/leds-lm3697.c

···
+// SPDX-License-Identifier: GPL-2.0
+// TI LM3697 LED chip family driver
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/leds-ti-lmu-common.h>
+
+#define LM3697_REV			0x0
+#define LM3697_RESET			0x1
+#define LM3697_OUTPUT_CONFIG		0x10
+#define LM3697_CTRL_A_RAMP		0x11
+#define LM3697_CTRL_B_RAMP		0x12
+#define LM3697_CTRL_A_B_RT_RAMP		0x13
+#define LM3697_CTRL_A_B_RAMP_CFG	0x14
+#define LM3697_CTRL_A_B_BRT_CFG		0x16
+#define LM3697_CTRL_A_FS_CURR_CFG	0x17
+#define LM3697_CTRL_B_FS_CURR_CFG	0x18
+#define LM3697_PWM_CFG			0x1c
+#define LM3697_CTRL_A_BRT_LSB		0x20
+#define LM3697_CTRL_A_BRT_MSB		0x21
+#define LM3697_CTRL_B_BRT_LSB		0x22
+#define LM3697_CTRL_B_BRT_MSB		0x23
+#define LM3697_CTRL_ENABLE		0x24
+
+#define LM3697_SW_RESET		BIT(0)
+
+#define LM3697_CTRL_A_EN	BIT(0)
+#define LM3697_CTRL_B_EN	BIT(1)
+#define LM3697_CTRL_A_B_EN	(LM3697_CTRL_A_EN | LM3697_CTRL_B_EN)
+
+#define LM3697_MAX_LED_STRINGS	3
+
+#define LM3697_CONTROL_A	0
+#define LM3697_CONTROL_B	1
+#define LM3697_MAX_CONTROL_BANKS 2
+
+/**
+ * struct lm3697_led -
+ * @hvled_strings: Array of LED strings associated with a control bank
+ * @label: LED label
+ * @led_dev: LED class device
+ * @priv: Pointer to the device struct
+ * @lmu_data: Register and setting values for common code
+ * @control_bank: Control bank the LED is associated to. 0 is control bank A
+ *		   1 is control bank B
+ */
+struct lm3697_led {
+	u32 hvled_strings[LM3697_MAX_LED_STRINGS];
+	char label[LED_MAX_NAME_SIZE];
+	struct led_classdev led_dev;
+	struct lm3697 *priv;
+	struct ti_lmu_bank lmu_data;
+	int control_bank;
+	int enabled;
+	int num_leds;
+};
+
+/**
+ * struct lm3697 -
+ * @enable_gpio: Hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: Pointer to the I2C client
+ * @regmap: Devices register map
+ * @dev: Pointer to the devices device struct
+ * @lock: Lock for reading/writing the device
+ * @leds: Array of LED strings
+ */
+struct lm3697 {
+	struct gpio_desc *enable_gpio;
+	struct regulator *regulator;
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct device *dev;
+	struct mutex lock;
+
+	int bank_cfg;
+
+	struct lm3697_led leds[];
+};
+
+static const struct reg_default lm3697_reg_defs[] = {
+	{LM3697_OUTPUT_CONFIG, 0x6},
+	{LM3697_CTRL_A_RAMP, 0x0},
+	{LM3697_CTRL_B_RAMP, 0x0},
+	{LM3697_CTRL_A_B_RT_RAMP, 0x0},
+	{LM3697_CTRL_A_B_RAMP_CFG, 0x0},
+	{LM3697_CTRL_A_B_BRT_CFG, 0x0},
+	{LM3697_CTRL_A_FS_CURR_CFG, 0x13},
+	{LM3697_CTRL_B_FS_CURR_CFG, 0x13},
+	{LM3697_PWM_CFG, 0xc},
+	{LM3697_CTRL_A_BRT_LSB, 0x0},
+	{LM3697_CTRL_A_BRT_MSB, 0x0},
+	{LM3697_CTRL_B_BRT_LSB, 0x0},
+	{LM3697_CTRL_B_BRT_MSB, 0x0},
+	{LM3697_CTRL_ENABLE, 0x0},
+};
+
+static const struct regmap_config lm3697_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LM3697_CTRL_ENABLE,
+	.reg_defaults = lm3697_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lm3697_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+static int lm3697_brightness_set(struct led_classdev *led_cdev,
+				enum led_brightness brt_val)
+{
+	struct lm3697_led *led = container_of(led_cdev, struct lm3697_led,
+					      led_dev);
+	int ctrl_en_val = (1 << led->control_bank);
+	int ret;
+
+	mutex_lock(&led->priv->lock);
+
+	if (brt_val == LED_OFF) {
+		ret = regmap_update_bits(led->priv->regmap, LM3697_CTRL_ENABLE,
+					 ctrl_en_val, ~ctrl_en_val);
+		if (ret) {
+			dev_err(&led->priv->client->dev, "Cannot write ctrl register\n");
+			goto brightness_out;
+		}
+
+		led->enabled = LED_OFF;
+	} else {
+		ret = ti_lmu_common_set_brightness(&led->lmu_data, brt_val);
+		if (ret) {
+			dev_err(&led->priv->client->dev,
+				"Cannot write brightness\n");
+			goto brightness_out;
+		}
+
+		if (!led->enabled) {
+			ret = regmap_update_bits(led->priv->regmap,
+						 LM3697_CTRL_ENABLE,
+						 ctrl_en_val, ctrl_en_val);
+			if (ret) {
+				dev_err(&led->priv->client->dev,
+					"Cannot enable the device\n");
+				goto brightness_out;
+			}
+
+			led->enabled = brt_val;
+		}
+	}
+
+brightness_out:
+	mutex_unlock(&led->priv->lock);
+	return ret;
+}
+
+static int lm3697_init(struct lm3697 *priv)
+{
+	struct lm3697_led *led;
+	int i, ret;
+
+	if (priv->enable_gpio) {
+		gpiod_direction_output(priv->enable_gpio, 1);
+	} else {
+		ret = regmap_write(priv->regmap, LM3697_RESET, LM3697_SW_RESET);
+		if (ret) {
+			dev_err(&priv->client->dev, "Cannot reset the device\n");
+			goto out;
+		}
+	}
+
+	ret = regmap_write(priv->regmap, LM3697_CTRL_ENABLE, 0x0);
+	if (ret) {
+		dev_err(&priv->client->dev, "Cannot write ctrl enable\n");
+		goto out;
+	}
+
+	ret = regmap_write(priv->regmap, LM3697_OUTPUT_CONFIG, priv->bank_cfg);
+	if (ret)
+		dev_err(&priv->client->dev, "Cannot write OUTPUT config\n");
+
+	for (i = 0; i < LM3697_MAX_CONTROL_BANKS; i++) {
+		led = &priv->leds[i];
+		ret = ti_lmu_common_set_ramp(&led->lmu_data);
+		if (ret)
+			dev_err(&priv->client->dev, "Setting the ramp rate failed\n");
+	}
+out:
+	return ret;
+}
+
+static int lm3697_probe_dt(struct lm3697 *priv)
+{
+	struct fwnode_handle *child = NULL;
+	struct lm3697_led *led;
+	const char *name;
+	int control_bank;
+	size_t i = 0;
+	int ret = -EINVAL;
+	int j;
+
+	priv->enable_gpio = devm_gpiod_get_optional(&priv->client->dev,
+						   "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->enable_gpio)) {
+		ret = PTR_ERR(priv->enable_gpio);
+		dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+			ret);
+		return ret;
+	}
+
+	priv->regulator = devm_regulator_get(&priv->client->dev, "vled");
+	if (IS_ERR(priv->regulator))
+		priv->regulator = NULL;
+
+	device_for_each_child_node(priv->dev, child) {
+		ret = fwnode_property_read_u32(child, "reg", &control_bank);
+		if (ret) {
+			dev_err(&priv->client->dev, "reg property missing\n");
+			fwnode_handle_put(child);
+			goto child_out;
+		}
+
+		if (control_bank > LM3697_CONTROL_B) {
+			dev_err(&priv->client->dev, "reg property is invalid\n");
+			ret = -EINVAL;
+			fwnode_handle_put(child);
+			goto child_out;
+		}
+
+		led = &priv->leds[i];
+
+		ret = ti_lmu_common_get_brt_res(&priv->client->dev,
+						child, &led->lmu_data);
+		if (ret)
+			dev_warn(&priv->client->dev, "brightness resolution property missing\n");
+
+		led->control_bank = control_bank;
+		led->lmu_data.regmap = priv->regmap;
+		led->lmu_data.runtime_ramp_reg = LM3697_CTRL_A_RAMP +
+						 control_bank;
+		led->lmu_data.msb_brightness_reg = LM3697_CTRL_A_BRT_MSB +
+						   led->control_bank * 2;
+		led->lmu_data.lsb_brightness_reg = LM3697_CTRL_A_BRT_LSB +
+						   led->control_bank * 2;
+
+		led->num_leds = fwnode_property_read_u32_array(child,
+						       "led-sources",
+						       NULL, 0);
+
+		if (led->num_leds > LM3697_MAX_LED_STRINGS) {
+			dev_err(&priv->client->dev, "To many LED strings defined\n");
+			continue;
+		}
+
+		ret = fwnode_property_read_u32_array(child, "led-sources",
+						    led->hvled_strings,
+						    led->num_leds);
+		if (ret) {
+			dev_err(&priv->client->dev, "led-sources property missing\n");
+			fwnode_handle_put(child);
+			goto child_out;
+		}
+
+		for (j = 0; j < led->num_leds; j++)
+			priv->bank_cfg |=
+				(led->control_bank << led->hvled_strings[j]);
+
+		ret = ti_lmu_common_get_ramp_params(&priv->client->dev,
+						    child, &led->lmu_data);
+		if (ret)
+			dev_warn(&priv->client->dev, "runtime-ramp properties missing\n");
+
+		fwnode_property_read_string(child, "linux,default-trigger",
+					    &led->led_dev.default_trigger);
+
+		ret = fwnode_property_read_string(child, "label", &name);
+		if (ret)
+			snprintf(led->label, sizeof(led->label),
+				"%s::", priv->client->name);
+		else
+			snprintf(led->label, sizeof(led->label),
+				 "%s:%s", priv->client->name, name);
+
+		led->priv = priv;
+		led->led_dev.name = led->label;
+		led->led_dev.max_brightness = led->lmu_data.max_brightness;
+		led->led_dev.brightness_set_blocking = lm3697_brightness_set;
+
+		ret = devm_led_classdev_register(priv->dev, &led->led_dev);
+		if (ret) {
+			dev_err(&priv->client->dev, "led register err: %d\n",
+				ret);
+			fwnode_handle_put(child);
+			goto child_out;
+		}
+
+		i++;
+	}
+
+child_out:
+	return ret;
+}
+
+static int lm3697_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct lm3697 *led;
+	int count;
+	int ret;
+
+	count = device_get_child_node_count(&client->dev);
+	if (!count) {
+		dev_err(&client->dev, "LEDs are not defined in device tree!");
+		return -ENODEV;
+	}
+
+	led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+			   GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	mutex_init(&led->lock);
+	i2c_set_clientdata(client, led);
+
+	led->client = client;
+	led->dev = &client->dev;
+	led->regmap = devm_regmap_init_i2c(client, &lm3697_regmap_config);
+	if (IS_ERR(led->regmap)) {
+		ret = PTR_ERR(led->regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = lm3697_probe_dt(led);
+	if (ret)
+		return ret;
+
+	return lm3697_init(led);
+}
+
+static int lm3697_remove(struct i2c_client *client)
+{
+	struct lm3697 *led = i2c_get_clientdata(client);
+	int ret;
+
+	ret = regmap_update_bits(led->regmap, LM3697_CTRL_ENABLE,
+				 LM3697_CTRL_A_B_EN, 0);
+	if (ret) {
+		dev_err(&led->client->dev, "Failed to disable the device\n");
+		return ret;
+	}
+
+	if (led->enable_gpio)
+		gpiod_direction_output(led->enable_gpio, 0);
+
+	if (led->regulator) {
+		ret = regulator_disable(led->regulator);
+		if (ret)
+			dev_err(&led->client->dev,
+				"Failed to disable regulator\n");
+	}
+
+	mutex_destroy(&led->lock);
+
+	return 0;
+}
+
+static const struct i2c_device_id lm3697_id[] = {
+	{ "lm3697", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, lm3697_id);
+
+static const struct of_device_id of_lm3697_leds_match[] = {
+	{ .compatible = "ti,lm3697", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lm3697_leds_match);
+
+static struct i2c_driver lm3697_driver = {
+	.driver = {
+		.name	= "lm3697",
+		.of_match_table = of_lm3697_leds_match,
+	},
+	.probe		= lm3697_probe,
+	.remove		= lm3697_remove,
+	.id_table	= lm3697_id,
+};
+module_i2c_driver(lm3697_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LM3697 LED driver");
+MODULE_AUTHOR("Dan Murphy <[e-mail]>");
+MODULE_LICENSE("GPL v2");

drivers/leds/leds-max77650.c

···
 {
 	struct device_node *of_node, *child;
 	struct max77650_led *leds, *led;
-	struct device *parent;
 	struct device *dev;
 	struct regmap *map;
 	const char *label;
···
 	u32 reg;
 
 	dev = &pdev->dev;
-	parent = dev->parent;
 	of_node = dev->of_node;
 
 	if (!of_node)

drivers/leds/leds-pca955x.c

···
 	int ngpios = 0;
 
 	chip = &pca955x_chipdefs[id->driver_data];
-	adapter = to_i2c_adapter(client->dev.parent);
+	adapter = client->adapter;
 	pdata = dev_get_platdata(&client->dev);
 	if (!pdata) {
 		pdata =	pca955x_get_pdata(client, chip);

drivers/leds/leds-spi-byte.c

···
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Christian Mauderer <[e-mail]>
+
+/*
+ * The driver supports controllers with a very simple SPI protocol:
+ * - one LED is controlled by a single byte on MOSI
+ * - the value of the byte gives the brightness between two values (lowest to
+ *   highest)
+ * - no return value is necessary (no MISO signal)
+ *
+ * The value for minimum and maximum brightness depends on the device
+ * (compatible string).
+ *
+ * Supported devices:
+ * - "ubnt,acb-spi-led": Microcontroller (SONiX 8F26E611LA) based device used
+ *   for example in Ubiquiti airCube ISP. Reverse engineered protocol for this
+ *   controller:
+ *   * Higher two bits set a mode. Lower six bits are a parameter.
+ *   * Mode: 00 -> set brightness between 0x00 (min) and 0x3F (max)
+ *   * Mode: 01 -> pulsing pattern (min -> max -> min) with an interval. From
+ *     some tests, the period is about (50ms + 102ms * parameter). There is a
+ *     slightly different pattern starting from 0x10 (longer gap between the
+ *     pulses) but the time still follows that calculation.
+ *   * Mode: 10 -> same as 01 but with only a ramp from min to max. Again a
+ *     slight jump in the pattern at 0x10.
+ *   * Mode: 11 -> blinking (off -> 25% -> off -> 25% -> ...) with a period of
+ *     (105ms * parameter)
+ *   NOTE: This driver currently only supports mode 00.
+ */
+
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mutex.h>
+#include <uapi/linux/uleds.h>
+
+struct spi_byte_chipdef {
+	/* SPI byte that will be send to switch the LED off */
+	u8	off_value;
+	/* SPI byte that will be send to switch the LED to maximum brightness */
+	u8	max_value;
+};
+
+struct spi_byte_led {
+	struct led_classdev		ldev;
+	struct spi_device		*spi;
+	char				name[LED_MAX_NAME_SIZE];
+	struct mutex			mutex;
+	const struct spi_byte_chipdef	*cdef;
+};
+
+static const struct spi_byte_chipdef ubnt_acb_spi_led_cdef = {
+	.off_value = 0x0,
+	.max_value = 0x3F,
+};
+
+static const struct of_device_id spi_byte_dt_ids[] = {
+	{ .compatible = "ubnt,acb-spi-led", .data = &ubnt_acb_spi_led_cdef },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, spi_byte_dt_ids);
+
+static int spi_byte_brightness_set_blocking(struct led_classdev *dev,
+					    enum led_brightness brightness)
+{
+	struct spi_byte_led *led = container_of(dev, struct spi_byte_led, ldev);
+	u8 value;
+	int ret;
+
+	value = (u8) brightness + led->cdef->off_value;
+
+	mutex_lock(&led->mutex);
+	ret = spi_write(led->spi, &value, sizeof(value));
+	mutex_unlock(&led->mutex);
+
+	return ret;
+}
+
+static int spi_byte_probe(struct spi_device *spi)
+{
+	const struct of_device_id *of_dev_id;
+	struct device_node *child;
+	struct device *dev = &spi->dev;
+	struct spi_byte_led *led;
+	const char *name = "leds-spi-byte::";
+	const char *state;
+	int ret;
+
+	of_dev_id = of_match_device(spi_byte_dt_ids, dev);
+	if (!of_dev_id)
+		return -EINVAL;
+
+	if (of_get_child_count(dev->of_node) != 1) {
+		dev_err(dev, "Device must have exactly one LED sub-node.");
+		return -EINVAL;
+	}
+	child = of_get_next_child(dev->of_node, NULL);
+
+	led = devm_kzalloc(dev, sizeof(*led), GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	of_property_read_string(child, "label", &name);
+	strlcpy(led->name, name, sizeof(led->name));
+	led->spi = spi;
+	mutex_init(&led->mutex);
+	led->cdef = of_dev_id->data;
+	led->ldev.name = led->name;
+	led->ldev.brightness = LED_OFF;
+	led->ldev.max_brightness = led->cdef->max_value - led->cdef->off_value;
+	led->ldev.brightness_set_blocking = spi_byte_brightness_set_blocking;
+
+	state = of_get_property(child, "default-state", NULL);
+	if (state) {
+		if (!strcmp(state, "on")) {
+			led->ldev.brightness = led->ldev.max_brightness;
+		} else if (strcmp(state, "off")) {
+			/* all other cases except "off" */
+			dev_err(dev, "default-state can only be 'on' or 'off'");
+			return -EINVAL;
+		}
+	}
+	spi_byte_brightness_set_blocking(&led->ldev,
+					 led->ldev.brightness);
+
+	ret = devm_led_classdev_register(&spi->dev, &led->ldev);
+	if (ret) {
+		mutex_destroy(&led->mutex);
+		return ret;
+	}
+	spi_set_drvdata(spi, led);
+
+	return 0;
+}
+
+static int spi_byte_remove(struct spi_device *spi)
+{
+	struct spi_byte_led	*led = spi_get_drvdata(spi);
+
+	mutex_destroy(&led->mutex);
+
+	return 0;
+}
+
+static struct spi_driver spi_byte_driver = {
+	.probe		= spi_byte_probe,
+	.remove		= spi_byte_remove,
+	.driver = {
+		.name		= KBUILD_MODNAME,
+		.of_match_table	= spi_byte_dt_ids,
+	},
+};
+
+module_spi_driver(spi_byte_driver);
+
+MODULE_AUTHOR("Christian Mauderer <[e-mail]>");
+MODULE_DESCRIPTION("single byte SPI LED driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("spi:leds-spi-byte");

drivers/leds/leds-tca6507.c

···
 	int err;
 	int i = 0;
 
-	adapter = to_i2c_adapter(client->dev.parent);
+	adapter = client->adapter;
 	pdata = dev_get_platdata(&client->dev);
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))

drivers/leds/leds-ti-lmu-common.c

···
+// SPDX-License-Identifier: GPL-2.0
+// Copyright 2015 Texas Instruments
+// Copyright 2018 Sebastian Reichel
+// Copyright 2018 Pavel Machek <[e-mail]>
+// TI LMU LED common framework, based on previous work from
+// Milo Kim <[e-mail]>
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/of_device.h>
+
+#include <linux/leds-ti-lmu-common.h>
+
+const static int ramp_table[16] = {2048, 262000, 524000, 1049000, 2090000,
+				4194000, 8389000, 16780000, 33550000, 41940000,
+				50330000, 58720000, 67110000, 83880000,
+				100660000, 117440000};
+
+static int ti_lmu_common_update_brightness(struct ti_lmu_bank *lmu_bank,
+					   int brightness)
+{
+	struct regmap *regmap = lmu_bank->regmap;
+	u8 reg, val;
+	int ret;
+
+	/*
+	 * Brightness register update
+	 *
+	 * 11 bit dimming: update LSB bits and write MSB byte.
+	 *		   MSB brightness should be shifted.
+	 *  8 bit dimming: write MSB byte.
+	 */
+	if (lmu_bank->max_brightness == MAX_BRIGHTNESS_11BIT) {
+		reg = lmu_bank->lsb_brightness_reg;
+		ret = regmap_update_bits(regmap, reg,
+					 LMU_11BIT_LSB_MASK,
+					 brightness);
+		if (ret)
+			return ret;
+
+		val = brightness >> LMU_11BIT_MSB_SHIFT;
+	} else {
+		val = brightness;
+	}
+
+	reg = lmu_bank->msb_brightness_reg;
+
+	return regmap_write(regmap, reg, val);
+}
+
+int ti_lmu_common_set_brightness(struct ti_lmu_bank *lmu_bank, int brightness)
+{
+	return ti_lmu_common_update_brightness(lmu_bank, brightness);
+}
+EXPORT_SYMBOL(ti_lmu_common_set_brightness);
+
+static int ti_lmu_common_convert_ramp_to_index(unsigned int usec)
+{
+	int size = ARRAY_SIZE(ramp_table);
+	int i;
+
+	if (usec <= ramp_table[0])
+		return 0;
+
+	if (usec > ramp_table[size - 1])
+		return size - 1;
+
+	for (i = 1; i < size; i++) {
+		if (usec == ramp_table[i])
+			return i;
+
+		/* Find an approximate index by looking up the table */
+		if (usec > ramp_table[i - 1] && usec < ramp_table[i]) {
+			if (usec - ramp_table[i - 1] < ramp_table[i] - usec)
+				return i - 1;
+			else
+				return i;
+		}
+	}
+
+	return -EINVAL;
+}
+
+int ti_lmu_common_set_ramp(struct ti_lmu_bank *lmu_bank)
+{
+	struct regmap *regmap = lmu_bank->regmap;
+	u8 ramp, ramp_up, ramp_down;
+
+	if (lmu_bank->ramp_up_usec == 0 && lmu_bank->ramp_down_usec == 0) {
+		ramp_up = 0;
+		ramp_down = 0;
+	} else {
+		ramp_up = ti_lmu_common_convert_ramp_to_index(lmu_bank->ramp_up_usec);
+		ramp_down = ti_lmu_common_convert_ramp_to_index(lmu_bank->ramp_down_usec);
+	}
+
+	if (ramp_up < 0 || ramp_down < 0)
+		return -EINVAL;
+
+	ramp = (ramp_up << 4) | ramp_down;
+
+	return regmap_write(regmap, lmu_bank->runtime_ramp_reg, ramp);
+
+}
+EXPORT_SYMBOL(ti_lmu_common_set_ramp);
+
+int ti_lmu_common_get_ramp_params(struct device *dev,
+				  struct fwnode_handle *child,
+				  struct ti_lmu_bank *lmu_data)
+{
+	int ret;
+
+	ret = fwnode_property_read_u32(child, "ramp-up-us",
+				 &lmu_data->ramp_up_usec);
+	if (ret)
+		dev_warn(dev, "ramp-up-us property missing\n");
+
+
+	ret = fwnode_property_read_u32(child, "ramp-down-us",
+				 &lmu_data->ramp_down_usec);
+	if (ret)
+		dev_warn(dev, "ramp-down-us property missing\n");
+
+	return 0;
+}
+EXPORT_SYMBOL(ti_lmu_common_get_ramp_params);
+
+int ti_lmu_common_get_brt_res(struct device *dev, struct fwnode_handle *child,
+				  struct ti_lmu_bank *lmu_data)
+{
+	int ret;
+
+	ret = device_property_read_u32(dev, "ti,brightness-resolution",
+				       &lmu_data->max_brightness);
+	if (ret)
+		ret = fwnode_property_read_u32(child,
+					       "ti,brightness-resolution",
+					       &lmu_data->max_brightness);
+	if (lmu_data->max_brightness <= 0) {
+		lmu_data->max_brightness = MAX_BRIGHTNESS_8BIT;
+		return ret;
+	}
+
+	if (lmu_data->max_brightness > MAX_BRIGHTNESS_11BIT)
+			lmu_data->max_brightness = MAX_BRIGHTNESS_11BIT;
+
+
+	return 0;
+}
+EXPORT_SYMBOL(ti_lmu_common_get_brt_res);
+
+MODULE_DESCRIPTION("TI LMU common LED framework");
+MODULE_AUTHOR("Sebastian Reichel");
+MODULE_AUTHOR("Dan Murphy <[e-mail]>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("ti-lmu-led-common");

drivers/leds/trigger/Kconfig

···
 	  This allows LEDs to be controlled by a programmable timer
 	  via sysfs. Some LED hardware can be programmed to start
 	  blinking the LED without any further software interaction.
-	  For more details read Documentation/leds/leds-class.txt.
+	  For more details read Documentation/leds/leds-class.rst.
 
 	  If unsure, say Y.
 

drivers/leds/trigger/ledtrig-transient.c

···
 // LED Kernel Transient Trigger
 //
 // Transient trigger allows one shot timer activation. Please refer to
-// Documentation/leds/ledtrig-transient.txt for details
+// Documentation/leds/ledtrig-transient.rst for details
 // Copyright (C) 2012 Shuah Khan <[e-mail]>
 //
 // Based on Richard Purdie's ledtrig-timer.c and Atsushi Nemoto's

drivers/mfd/Kconfig

···
 	select REGMAP_I2C
 	help
 	  Say yes here to enable support for TI LMU chips.
-
-	  TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
-	  It consists of backlight, LED and regulator driver.
+	  TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and
+	  LM36274.  It consists of backlight, LED and regulator driver.
 	  It provides consistent device controls for lighting functions.
 
 config MFD_OMAP_USB_HOST

drivers/mfd/ti-lmu.c

···
 	},
 };
 
-static const struct mfd_cell lm3697_devices[] = {
+static const struct mfd_cell lm36274_devices[] = {
+	LM363X_REGULATOR(LM36274_BOOST),
+	LM363X_REGULATOR(LM36274_LDO_POS),
+	LM363X_REGULATOR(LM36274_LDO_NEG),
 	{
-		.name          = "ti-lmu-backlight",
-		.id            = LM3697,
-		.of_compatible = "ti,lm3697-backlight",
-	},
-	/* Monitoring driver for open/short circuit detection */
-	{
-		.name          = "ti-lmu-fault-monitor",
-		.id            = LM3697,
-		.of_compatible = "ti,lm3697-fault-monitor",
+		.name          = "lm36274-leds",
+		.id            = LM36274,
+		.of_compatible = "ti,lm36274-backlight",
 	},
 };
 
···
 TI_LMU_DATA(lm3632, LM3632_MAX_REG);
 TI_LMU_DATA(lm3633, LM3633_MAX_REG);
 TI_LMU_DATA(lm3695, LM3695_MAX_REG);
-TI_LMU_DATA(lm3697, LM3697_MAX_REG);
+TI_LMU_DATA(lm36274, LM36274_MAX_REG);
 
 static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 {
···
 	{ .compatible = "ti,lm3632", .data = &lm3632_data },
 	{ .compatible = "ti,lm3633", .data = &lm3633_data },
 	{ .compatible = "ti,lm3695", .data = &lm3695_data },
-	{ .compatible = "ti,lm3697", .data = &lm3697_data },
+	{ .compatible = "ti,lm36274", .data = &lm36274_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
···
 	{ "lm3632", LM3632 },
 	{ "lm3633", LM3633 },
 	{ "lm3695", LM3695 },
-	{ "lm3697", LM3697 },
+	{ "lm36274", LM36274 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);

drivers/regulator/Kconfig

···
 	tristate "TI LM363X voltage regulators"
 	depends on MFD_TI_LMU
 	help
-	  This driver supports LM3631 and LM3632 voltage regulators for
+	  This driver supports LM3631, LM3632 and LM36274 voltage regulators for
 	  the LCD bias.
 	  One boost output voltage is configurable and always on.
 	  Other LDOs are used for the display module.

drivers/regulator/lm363x-regulator.c

···
 #define LM3632_VBOOST_MIN		4500000
 #define LM3632_VLDO_MIN			4000000
 
+/* LM36274 */
+#define LM36274_BOOST_VSEL_MAX		0x3f
+#define LM36274_LDO_VSEL_MAX		0x34
+#define LM36274_VOLTAGE_MIN		4000000
+
 /* Common */
 #define LM363X_STEP_50mV		50000
 #define LM363X_STEP_500mV		500000
···
 		.enable_reg     = LM3632_REG_BIAS_CONFIG,
 		.enable_mask    = LM3632_EN_VNEG_MASK,
 	},
+
+	/* LM36274 */
+	{
+		.name           = "vboost",
+		.of_match	= "vboost",
+		.id             = LM36274_BOOST,
+		.ops            = &lm363x_boost_voltage_table_ops,
+		.n_voltages     = LM36274_BOOST_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_BOOST,
+		.vsel_mask      = LM36274_VOUT_MASK,
+	},
+	{
+		.name           = "ldo_vpos",
+		.of_match	= "vpos",
+		.id             = LM36274_LDO_POS,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_POS,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VPOS_MASK,
+	},
+	{
+		.name           = "ldo_vneg",
+		.of_match	= "vneg",
+		.id             = LM36274_LDO_NEG,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_NEG,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VNEG_MASK,
+	},
 };
 
 static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev, int id)
···
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
+	case LM36274_LDO_POS:
 		return gpiod_get_index_optional(dev, "enable", 0,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
+	case LM36274_LDO_NEG:
 		return gpiod_get_index_optional(dev, "enable", 1,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
 		return NULL;
 	}
+}
+
+static int lm363x_regulator_set_ext_en(struct regmap *regmap, int id)
+{
+	int ext_en_mask = 0;
+
+	switch (id) {
+	case LM3632_LDO_POS:
+	case LM3632_LDO_NEG:
+		ext_en_mask = LM3632_EXT_EN_MASK;
+		break;
+	case LM36274_LDO_POS:
+	case LM36274_LDO_NEG:
+		ext_en_mask = LM36274_EXT_EN_MASK;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	return regmap_update_bits(regmap, lm363x_regulator_desc[id].enable_reg,
+				 ext_en_mask, ext_en_mask);
 }
 
 static int lm363x_regulator_probe(struct platform_device *pdev)
···
 
 	if (gpiod) {
 		cfg.ena_gpiod = gpiod;
-
-		ret = regmap_update_bits(regmap, LM3632_REG_BIAS_CONFIG,
-					 LM3632_EXT_EN_MASK,
-					 LM3632_EXT_EN_MASK);
+		ret = lm363x_regulator_set_ext_en(regmap, id);
 		if (ret) {
 			gpiod_put(gpiod);
 			dev_err(dev, "External pin err: %d\n", ret);

include/linux/leds-ti-lmu-common.h

···
+/* SPDX-License-Identifier: GPL-2.0 */
+// TI LMU Common Core
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#ifndef _TI_LMU_COMMON_H_
+#define _TI_LMU_COMMON_H_
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#define LMU_11BIT_LSB_MASK	(BIT(0) | BIT(1) | BIT(2))
+#define LMU_11BIT_MSB_SHIFT	3
+
+#define MAX_BRIGHTNESS_8BIT	255
+#define MAX_BRIGHTNESS_11BIT	2047
+
+struct ti_lmu_bank {
+	struct regmap *regmap;
+
+	int max_brightness;
+
+	u8 lsb_brightness_reg;
+	u8 msb_brightness_reg;
+
+	u8 runtime_ramp_reg;
+	u32 ramp_up_usec;
+	u32 ramp_down_usec;
+};
+
+int ti_lmu_common_set_brightness(struct ti_lmu_bank *lmu_bank, int brightness);
+
+int ti_lmu_common_set_ramp(struct ti_lmu_bank *lmu_bank);
+
+int ti_lmu_common_get_ramp_params(struct device *dev,
+				  struct fwnode_handle *child,
+				  struct ti_lmu_bank *lmu_data);
+
+int ti_lmu_common_get_brt_res(struct device *dev, struct fwnode_handle *child,
+			      struct ti_lmu_bank *lmu_data);
+
+#endif /* _TI_LMU_COMMON_H_ */

include/linux/mfd/ti-lmu-register.h

···
 
 #define LM3695_MAX_REG				0x14
 
-/* LM3697 */
-#define LM3697_REG_HVLED_OUTPUT_CFG		0x10
-#define LM3697_HVLED1_CFG_MASK			BIT(0)
-#define LM3697_HVLED2_CFG_MASK			BIT(1)
-#define LM3697_HVLED3_CFG_MASK			BIT(2)
-#define LM3697_HVLED1_CFG_SHIFT			0
-#define LM3697_HVLED2_CFG_SHIFT			1
-#define LM3697_HVLED3_CFG_SHIFT			2
+/* LM36274 */
+#define LM36274_REG_REV				0x01
+#define LM36274_REG_BL_CFG_1			0x02
+#define LM36274_REG_BL_CFG_2			0x03
+#define LM36274_REG_BRT_LSB			0x04
+#define LM36274_REG_BRT_MSB			0x05
+#define LM36274_REG_BL_EN			0x08
 
-#define LM3697_REG_BL0_RAMP			0x11
-#define LM3697_REG_BL1_RAMP			0x12
-#define LM3697_RAMPUP_MASK			0xF0
-#define LM3697_RAMPUP_SHIFT			4
-#define LM3697_RAMPDN_MASK			0x0F
-#define LM3697_RAMPDN_SHIFT			0
+#define LM36274_REG_BIAS_CONFIG_1		0x09
+#define LM36274_EXT_EN_MASK			BIT(0)
+#define LM36274_EN_VNEG_MASK			BIT(1)
+#define LM36274_EN_VPOS_MASK			BIT(2)
 
-#define LM3697_REG_RAMP_CONF			0x14
-#define LM3697_RAMP_MASK			0x0F
-#define LM3697_RAMP_EACH			0x05
+#define LM36274_REG_BIAS_CONFIG_2		0x0a
+#define LM36274_REG_BIAS_CONFIG_3		0x0b
+#define LM36274_REG_VOUT_BOOST			0x0c
+#define LM36274_REG_VOUT_POS			0x0d
+#define LM36274_REG_VOUT_NEG			0x0e
+#define LM36274_VOUT_MASK			0x3F
 
-#define LM3697_REG_PWM_CFG			0x1C
-#define LM3697_PWM_A_MASK			BIT(0)
-#define LM3697_PWM_B_MASK			BIT(1)
+#define LM36274_MAX_REG				0x13
 
-#define LM3697_REG_IMAX_A			0x17
-#define LM3697_REG_IMAX_B			0x18
-
-#define LM3697_REG_FEEDBACK_ENABLE		0x19
-
-#define LM3697_REG_BRT_A_LSB			0x20
-#define LM3697_REG_BRT_A_MSB			0x21
-#define LM3697_REG_BRT_B_LSB			0x22
-#define LM3697_REG_BRT_B_MSB			0x23
-
-#define LM3697_REG_ENABLE			0x24
-
-#define LM3697_REG_OPEN_FAULT_STATUS		0xB0
-
-#define LM3697_REG_SHORT_FAULT_STATUS		0xB2
-
-#define LM3697_REG_MONITOR_ENABLE		0xB4
-
-#define LM3697_MAX_REG				0xB4
 #endif

include/linux/mfd/ti-lmu.h

···
 	LM3632,
 	LM3633,
 	LM3695,
-	LM3697,
+	LM36274,
 	LMU_MAX_ID,
 };
 
···
 	LM3632_BOOST,		/* Boost output */
 	LM3632_LDO_POS,		/* Positive display bias output */
 	LM3632_LDO_NEG,		/* Negative display bias output */
+	LM36274_BOOST,		/* Boost output */
+	LM36274_LDO_POS,	/* Positive display bias output */
+	LM36274_LDO_NEG,	/* Negative display bias output */
 };
 
 /**

net/netfilter/Kconfig

···
 	    echo netfilter-ssh > /sys/class/leds/<ledname>/trigger
 
 	  For more information on the LEDs available on your system, see
-	  Documentation/leds/leds-class.txt
+	  Documentation/leds/leds-class.rst
 
 config NETFILTER_XT_TARGET_LOG
 	tristate "LOG target support"