Merge tag 'renesas-arm-dt-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.16

- I2C EEPROM support on the RZA2MEVB development board,
- DMA, USB2.0, and audio support for the RZ/G2L SoC,
- USB2.0, I2C, audio, ADC, and CANFD support for the RZ/G2L SMARC EVK
development board,
- Support for more R-Car Gen3e SoCs (H3e, M3e, M3Ne(-2G), D3e, E3e,
H3Ne),
- PWM support for the R-Car M3-W+ and V3U SoCs,
- IPMMU support for SDHI on the R-Car V3U SoC,
- Switches support for the Falcon development board,
- Improve Ethernet PHY descriptions to fix reset handling after kexec,
- Miscellaneous fixes and improvements.

* tag 'renesas-arm-dt-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (45 commits)
arm64: dts: renesas: rcar-gen3: Add missing Ethernet PHY resets
ARM: dts: rzg1: Add missing Ethernet PHY resets
ARM: dts: r-mobile: Add missing Ethernet PHY resets
arm64: dts: renesas: Add compatible properties to RTL8211E Ethernet PHYs
arm64: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
arm64: dts: renesas: Add compatible properties to AR8031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to uPD6061x Ethernet PHYs
ARM: dts: renesas: Add compatible properties to RTL8201FL Ethernet PHYs
ARM: dts: renesas: Add compatible properties to LAN8710A Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8081 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8041 Ethernet PHYs
arm64: dts: renesas: beacon: Fix Ethernet PHY mode
ARM: dts: renesas: Fix SMSC Ethernet compatible values
arm64: dts: renesas: rzg2l-smarc: Enable CANFD
arm64: dts: renesas: rzg2l-smarc-som: Enable ADC on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Move extal and memory nodes to SOM DTSI
arm64: dts: renesas: r8a779a0: falcon-cpu: Add SW47-SW49 support
arm64: dts: renesas: rzg2l-smarc: Add Mic routing
arm64: dts: renesas: rzg2l-smarc: Enable audio
...

Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Arnd Bergmann <[e-mail]>

arch/arm/boot/dts/emev2-kzm9d.dts

···
 	};
 
 	ethernet@20000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan9221", "smsc,lan9115";
 		reg = <0x20000000 0x10000>;
 		phy-mode = "mii";
 		interrupt-parent = <&gpio0>;

arch/arm/boot/dts/iwg20d-q7-common.dtsi

···
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		micrel,led-mode = <1>;
 	};

arch/arm/boot/dts/r7s72100-genmai.dts

···
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-idb824.2814",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };

arch/arm/boot/dts/r7s72100-gr-peach.dts

···
 	phy-handle = <&phy0>;
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 
 		reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;

arch/arm/boot/dts/r7s72100-rskrza1.dts

···
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-idb824.2814",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };

arch/arm/boot/dts/r7s9210-rza2mevb.dts

···
 	renesas,no-ether-link;
 	phy-handle = <&phy1>;
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id001c.c816",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };
···
 /* EXTAL */
 &extal_clk {
 	clock-frequency = <24000000>;	/* 24MHz */
+};
+
+&i2c3 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	eeprom@50 {
+		compatible = "renesas,r1ex24128", "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
 };
 
 /* High resolution System tick timers */
···
 			 <RZA2_PINMUX(PORT3, 3, 1)>, /* ET1_MDC */
 			 <RZA2_PINMUX(PORT3, 4, 1)>, /* ET1_MDIO */
 			 <RZA2_PINMUX(PORTL, 1, 5)>; /* IRQ5 */
+	};
+
+	i2c3_pins: i2c3 {
+		pinmux = <RZA2_PINMUX(PORTD, 6, 1)>,	/* RIIC3SCL */
+			 <RZA2_PINMUX(PORTD, 7, 1)>;	/* RIIC3SDA */
 	};
 
 	keyboard_pins: keyboard {

arch/arm/boot/dts/r8a73a4-ape6evm.dts

···
 		reg-io-width = <4>;
 		smsc,irq-active-high;
 		smsc,irq-push-pull;
+		reset-gpios = <&pfc 270 GPIO_ACTIVE_LOW>;
 		vdd33a-supply = <&ape6evm_fixed_3v3>;
 		vddvario-supply = <&ape6evm_fixed_1v8>;
 	};

arch/arm/boot/dts/r8a7740-armadillo800eva.dts

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f1",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
+		reset-gpios = <&pfc 18 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1560",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		micrel,led-mode = <1>;
 	};

arch/arm/boot/dts/r8a7742-iwg21d-q7.dts

···
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		micrel,led-mode = <1>;
 	};

arch/arm/boot/dts/r8a7743-sk-rzg1m.dts

···
 
 /dts-v1/;
 #include "r8a7743.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "SK-RZG1M";
···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 	};
 };

arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts

···
 	 * On some older versions of the platform (before R4.0) the phy address
 	 * may be 1 or 3. The address is fixed to 3 for R4.0 onwards.
 	 */
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		micrel,led-mode = <1>;
 	};

arch/arm/boot/dts/r8a7745-sk-rzg1e.dts

···
 
 /dts-v1/;
 #include "r8a7745.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "SK-RZG1E";
···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	};
 };

arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts

···
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7778-bockw.dts

···
 
 &bsc {
 	ethernet@18300000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan89218", "smsc,lan9115";
 		reg = <0x18300000 0x1000>;
 
 		phy-mode = "mii";

arch/arm/boot/dts/r8a7779-marzen.dts

···
 	};
 
 	ethernet@18000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan89218", "smsc,lan9115";
 		reg = <0x18000000 0x100>;
 		pinctrl-0 = <&ethernet_pins>;
 		pinctrl-names = "default";

arch/arm/boot/dts/r8a7790-lager.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7790-stout.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7791-koelsch.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7791-porter.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7793-gose.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7794-alt.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/r8a7794-silk.dts

···
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;

arch/arm/boot/dts/sh73a0-kzm9g.dts

···
 
 &bsc {
 	ethernet@10000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan9221", "smsc,lan9115";
 		reg = <0x10000000 0x100>;
 		phy-mode = "mii";
 		interrupt-parent = <&irqpin0>;

arch/arm64/boot/dts/renesas/Makefile

···
 dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb-kf.dtb
 
+dtb-$(CONFIG_ARCH_R8A77965) += r8a779m5-salvator-xs.dtb
+
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc.dtb

arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi

···
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&phy0>;
 	rx-internal-delay-ps = <1800>;
 	tx-internal-delay-ps = <2000>;
···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id004d.d074",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;

arch/arm64/boot/dts/renesas/cat875.dtsi

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c915",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;

arch/arm64/boot/dts/renesas/draak.dtsi

···
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Draak board
+ *
+ * Copyright (C) 2016-2018 Renesas Electronics Corp.
+ * Copyright (C) 2017 Glider bvba
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Renesas Draak board";
+	compatible = "renesas,draak";
+
+	aliases {
+		serial0 = &scif2;
+		ethernet0 = &avb;
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000>;
+
+		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
+		default-brightness-level = <10>;
+
+		power-supply = <&reg_12p0v>;
+		enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:115200n8";
+	};
+
+	composite-in {
+		compatible = "composite-video-connector";
+
+		port {
+			composite_con_in: endpoint {
+				remote-endpoint = <&adv7180_in>;
+			};
+		};
+	};
+
+	hdmi-in {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&adv7612_in>;
+			};
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_out: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW56-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW56-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW56-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW56-4";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+		vcc-supply = <&reg_3p3v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				thc63lvd1024_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				thc63lvd1024_out: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x18000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_12p0v: regulator-12p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "D12.0V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sound_card: sound {
+		compatible = "audio-graph-card";
+
+		dais = <&rsnd_port0	/* ak4613 */
+			/* HDMI is not yet supported */
+		>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+
+	x19_clk: x19 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&audio_clk_b {
+	/*
+	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
+	 * and R-Car Sound uses AUDIO_CLKB.
+	 * Note is that schematic indicates VI4_FIELD conection only
+	 * not AUDIO_CLKB at SoC page.
+	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
+	 * SW60 should be 1-2.
+	 */
+
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+		/*
+		 * TX clock internal delay mode is required for reliable
+		 * 1Gbps communication using the KSZ9031RNX phy present on
+		 * the Draak board, however, TX clock internal delay mode
+		 * isn't supported on R-Car D3(e).  Thus, limit speed to
+		 * 100Mbps for reliable communication.
+		 */
+		max-speed = <100>;
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&can0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-0 = <&can1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&x12_clk>;
+	clock-names = "du.0", "du.1", "dclkin.0";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+	};
+};
+
+&ehci0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <48000000>;
+};
+
+&hsusb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 0>; /* audio_clkout */
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+
+		port {
+			ak4613_endpoint: endpoint {
+				remote-endpoint = <&rsnd_for_ak4613>;
+			};
+		};
+	};
+
+	composite-in@20 {
+		compatible = "adi,adv7180cp";
+		reg = <0x20>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7180_in: endpoint {
+					remote-endpoint = <&composite_con_in>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				/*
+				 * The VIN4 video input path is shared between
+				 * CVBS and HDMI inputs through SW[49-53]
+				 * switches.
+				 *
+				 * CVBS is the default selection, link it to
+				 * VIN4 here.
+				 */
+				adv7180_out: endpoint {
+					remote-endpoint = <&vin4_in>;
+				};
+			};
+		};
+
+	};
+
+	hdmi-encoder@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
+		reg-names = "main", "edid", "cec", "packet";
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&thc63lvd1024_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+
+	hdmi-decoder@4c {
+		compatible = "adi,adv7612";
+		reg = <0x4c>;
+		default-input = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7612_in: endpoint {
+					remote-endpoint = <&hdmi_con_in>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				/*
+				 * The VIN4 video input path is shared between
+				 * CVBS and HDMI inputs through SW[49-53]
+				 * switches.
+				 *
+				 * CVBS is the default selection, leave HDMI
+				 * not connected here.
+				 */
+				adv7612_out: endpoint {
+					pclk-sample = <0>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+				};
+			};
+		};
+	};
+
+	cs2000: clk-multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+
+	eeprom@50 {
+		compatible = "rohm,br24t01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&lvds0 {
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x12_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&thc63lvd1024_in>;
+			};
+		};
+	};
+};
+
+&lvds1 {
+	/*
+	 * Even though the LVDS1 output is not connected, the encoder must be
+	 * enabled to supply a pixel clock to the DU for the DPAD output when
+	 * LVDS0 is in use.
+	 */
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x12_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+};
+
+&ohci0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&pfc {
+	avb0_pins: avb {
+		groups = "avb0_link", "avb0_mdio", "avb0_mii";
+		function = "avb0";
+	};
+
+	can0_pins: can0 {
+		groups = "can0_data_a";
+		function = "can0";
+	};
+
+	can1_pins: can1 {
+		groups = "can1_data_a";
+		function = "can1";
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
+		function = "du";
+	};
+
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	i2c1_pins: i2c1 {
+		groups = "i2c1";
+		function = "i2c1";
+	};
+
+	keys_pins: keys {
+		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
+		bias-pull-up;
+	};
+
+	pwm0_pins: pwm0 {
+		groups = "pwm0_c";
+		function = "pwm0";
+	};
+
+	pwm1_pins: pwm1 {
+		groups = "pwm1_c";
+		function = "pwm1";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data";
+		function = "scif2";
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "mmc_data8", "mmc_ctrl";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "mmc_data8", "mmc_ctrl";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound-clk {
+		groups = "audio_clk_a", "audio_clk_b",
+			 "audio_clkout", "audio_clkout1";
+		function = "audio_clk";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	vin4_pins_cvbs: vin4 {
+		groups = "vin4_data8", "vin4_sync", "vin4_clk";
+		function = "vin4";
+	};
+};
+
+&pwm0 {
+	pinctrl-0 = <&pwm0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1 */
+	#clock-cells = <1>;
+	clock-frequency = <12288000 11289600>;
+
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
+		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&cs2000>, <&audio_clk_b>,
+		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
+
+	ports {
+		rsnd_port0: port {
+			rsnd_for_ak4613: endpoint {
+				remote-endpoint = <&ak4613_endpoint>;
+				dai-format = "left_j";
+				bitclock-master = <&rsnd_for_ak4613>;
+				frame-master = <&rsnd_for_ak4613>;
+				playback = <&ssi3>, <&src5>, <&dvc0>;
+				capture  = <&ssi4>, <&src6>, <&dvc1>;
+			};
+		};
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&ssi4 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	renesas,no-otg-pins;
+	status = "okay";
+};
+
+&vin4 {
+	pinctrl-0 = <&vin4_pins_cvbs>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	ports {
+		port {
+			vin4_in: endpoint {
+				remote-endpoint = <&adv7180_out>;
+			};
+		};
+	};
+};

arch/arm64/boot/dts/renesas/ebisu.dtsi

···
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Ebisu board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Renesas Ebisu board";
+	compatible = "renesas,ebisu";
+
+	aliases {
+		serial0 = &scif2;
+		ethernet0 = &avb;
+		mmc0 = &sdhi3;
+		mmc1 = &sdhi0;
+		mmc2 = &sdhi1;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 50000>;
+
+		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
+		default-brightness-level = <10>;
+
+		power-supply = <&reg_12p0v>;
+	};
+
+	cvbs-in {
+		compatible = "composite-video-connector";
+		label = "CVBS IN";
+
+		port {
+			cvbs_con: endpoint {
+				remote-endpoint = <&adv7482_ain7>;
+			};
+		};
+	};
+
+	hdmi-in {
+		compatible = "hdmi-connector";
+		label = "HDMI IN";
+		type = "a";
+
+		port {
+			hdmi_in_con: endpoint {
+				remote-endpoint = <&adv7482_hdmi>;
+			};
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_out: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW4-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW4-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW4-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW4-4";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+		vcc-supply = <&reg_3p3v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				thc63lvd1024_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				thc63lvd1024_out: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_12p0v: regulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "D12.0V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "rsnd-ak4613";
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+	};
+
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS_CN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	vcc_sdhi1: regulator-vcc-sdhi1 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	x13_clk: x13 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		/*
+		 * TX clock internal delay mode is required for reliable
+		 * 1Gbps communication using the KSZ9031RNX phy present on
+		 * the Ebisu board, however, TX clock internal delay mode
+		 * isn't supported on R-Car E3(e).  Thus, limit speed to
+		 * 100Mbps for reliable communication.
+		 */
+		max-speed = <100>;
+	};
+};
+
+&canfd {
+	pinctrl-0 = <&canfd0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+};
+
+&csi40 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&adv7482_txa>;
+			};
+		};
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&x13_clk>;
+	clock-names = "du.0", "du.1", "dclkin.0";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+	};
+};
+
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <48000000>;
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	io_expander: gpio@20 {
+		compatible = "onnn,pca9654";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	hdmi-encoder@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&thc63lvd1024_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+
+	video-receiver@70 {
+		compatible = "adi,adv7482";
+		reg = <0x70>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gpio0>;
+		interrupt-names = "intrq1", "intrq2";
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
+			     <17 IRQ_TYPE_LEVEL_LOW>;
+
+		port@7 {
+			reg = <7>;
+
+			adv7482_ain7: endpoint {
+				remote-endpoint = <&cvbs_con>;
+			};
+		};
+
+		port@8 {
+			reg = <8>;
+
+			adv7482_hdmi: endpoint {
+				remote-endpoint = <&hdmi_in_con>;
+			};
+		};
+
+		port@a {
+			reg = <10>;
+
+			adv7482_txa: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi40_in>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk-multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&i2c_dvfs {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pmic: pmic@30 {
+		pinctrl-0 = <&irq0_pins>;
+		pinctrl-names = "default";
+
+		compatible = "rohm,bd9571mwv";
+		reg = <0x30>;
+		interrupt-parent = <&intc_ex>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		rohm,ddr-backup-power = <0x1>;
+		rohm,rstbmode-level;
+	};
+
+	eeprom@50 {
+		compatible = "rohm,br24t01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x13_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&thc63lvd1024_in>;
+			};
+		};
+	};
+};
+
+&lvds1 {
+	/*
+	 * Even though the LVDS1 output is not connected, the encoder must be
+	 * enabled to supply a pixel clock to the DU for the DPAD output when
+	 * LVDS0 is in use.
+	 */
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x13_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+};
+
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	status = "okay";
+};
+
+&pfc {
+	avb_pins: avb {
+		groups = "avb_link", "avb_mii";
+		function = "avb";
+	};
+
+	canfd0_pins: canfd0 {
+		groups = "canfd0_data";
+		function = "canfd0";
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
+		function = "du";
+	};
+
+	irq0_pins: irq0 {
+		groups = "intc_ex_irq0";
+		function = "intc_ex";
+	};
+
+	keys_pins: keys {
+		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
+		bias-pull-up;
+	};
+
+	pwm3_pins: pwm3 {
+		groups = "pwm3_b";
+		function = "pwm3";
+	};
+
+	pwm5_pins: pwm5 {
+		groups = "pwm5_a";
+		function = "pwm5";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi1_pins: sd1 {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <3300>;
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <1800>;
+	};
+
+	sdhi3_pins: sd3 {
+		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
+		function = "sdhi3";
+		power-source = <1800>;
+	};
+
+	sound_clk_pins: sound_clk {
+		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout1_a";
+		function = "audio_clk";
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
+		function = "ssi";
+	};
+
+	usb0_pins: usb {
+		groups = "usb0_b", "usb0_id";
+		function = "usb0";
+	};
+
+	usb30_pins: usb30 {
+		groups = "usb30";
+		function = "usb30";
+	};
+};
+
+&pwm3 {
+	pinctrl-0 = <&pwm3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pwm5 {
+	pinctrl-0 = <&pwm5_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <12288000 11289600>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
+		 <&cpg CPG_CORE R8A77990_CLK_ZA2>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0>, <&src0>, <&dvc0>;
+			capture  = <&ssi1>, <&src1>, <&dvc1>;
+		};
+	};
+
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi1>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdhi3 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi3_pins>;
+	pinctrl-1 = <&sdhi3_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	full-pwr-cycle-in-suspend;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb3_peri0 {
+	companion = <&xhci0>;
+	status = "okay";
+};
+
+&vin4 {
+	status = "okay";
+};
+
+&vin5 {
+	status = "okay";
+};
+
+&xhci0 {
+	pinctrl-0 = <&usb30_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};

arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c915",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;

arch/arm64/boot/dts/renesas/r8a77961.dtsi

···
 			status = "disabled";
 		};
 
+		tpu: pwm@e6e80000 {
+			compatible = "renesas,tpu-r8a77961", "renesas,tpu";
+			reg = <0 0xe6e80000 0 0x148>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 304>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 304>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a77961",
 				     "renesas,rcar-gen3-msiof";

arch/arm64/boot/dts/renesas/r8a77970-eagle.dts

···
 
 /dts-v1/;
 #include "r8a77970.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas Eagle board based on r8a77970";
···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts

···
 
 /dts-v1/;
 #include "r8a77970.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas V3M Starter Kit board";
···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm64/boot/dts/renesas/r8a77980-condor.dts

···
 
 /dts-v1/;
 #include "r8a77980.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas Condor board based on r8a77980";
···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts

···
 
 /dts-v1/;
 #include "r8a77980.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas V3H Starter Kit board";
···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts

···
 
 /dts-v1/;
 #include "r8a77990.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ebisu.dtsi"
 
 / {
 	model = "Renesas Ebisu board based on r8a77990";
 	compatible = "renesas,ebisu", "renesas,r8a77990";
-
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-		mmc0 = &sdhi3;
-		mmc1 = &sdhi0;
-		mmc2 = &sdhi1;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 50000>;
-
-		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
-		default-brightness-level = <10>;
-
-		power-supply = <&reg_12p0v>;
-	};
-
-	cvbs-in {
-		compatible = "composite-video-connector";
-		label = "CVBS IN";
-
-		port {
-			cvbs_con: endpoint {
-				remote-endpoint = <&adv7482_ain7>;
-			};
-		};
-	};
-
-	hdmi-in {
-		compatible = "hdmi-connector";
-		label = "HDMI IN";
-		type = "a";
-
-		port {
-			hdmi_in_con: endpoint {
-				remote-endpoint = <&adv7482_hdmi>;
-			};
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_out: endpoint {
-				remote-endpoint = <&adv7511_out>;
-			};
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		pinctrl-0 = <&keys_pins>;
-		pinctrl-names = "default";
-
-		key-1 {
-			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_1>;
-			label = "SW4-1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-2 {
-			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_2>;
-			label = "SW4-2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-3 {
-			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_3>;
-			label = "SW4-3";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-4 {
-			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_4>;
-			label = "SW4-4";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-	};
-
-	lvds-decoder {
-		compatible = "thine,thc63lvd1024";
-		vcc-supply = <&reg_3p3v>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				thc63lvd1024_in: endpoint {
-					remote-endpoint = <&lvds0_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				thc63lvd1024_out: endpoint {
-					remote-endpoint = <&adv7511_in>;
-				};
-			};
-		};
-	};
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x38000000>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_12p0v: regulator2 {
-		compatible = "regulator-fixed";
-		regulator-name = "D12.0V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,name = "rsnd-ak4613";
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS_CN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vcc_sdhi1: regulator-vcc-sdhi1 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI1 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi1: regulator-vccq-sdhi1 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI1 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	x13_clk: x13 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <74250000>;
-	};
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
-		/*
-		 * TX clock internal delay mode is required for reliable
-		 * 1Gbps communication using the KSZ9031RNX phy present on
-		 * the Ebisu board, however, TX clock internal delay mode
-		 * isn't supported on r8a77990.  Thus, limit speed to
-		 * 100Mbps for reliable communication.
-		 */
-		max-speed = <100>;
-	};
-};
-
-&canfd {
-	pinctrl-0 = <&canfd0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	channel0 {
-		status = "okay";
-	};
-};
-
-&csi40 {
-	status = "okay";
-
-	ports {
-		port@0 {
-			csi40_in: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-				remote-endpoint = <&adv7482_txa>;
-			};
-		};
-	};
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 724>,
-		 <&cpg CPG_MOD 723>,
-		 <&x13_clk>;
-	clock-names = "du.0", "du.1", "dclkin.0";
-
-	ports {
-		port@0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-	};
-};
-
-&ehci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <48000000>;
-};
-
-&hsusb {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&i2c0 {
-	status = "okay";
-
-	io_expander: gpio@20 {
-		compatible = "onnn,pca9654";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
-	};
-
-	hdmi-encoder@39 {
-		compatible = "adi,adv7511w";
-		reg = <0x39>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511_in: endpoint {
-					remote-endpoint = <&thc63lvd1024_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con_out>;
-				};
-			};
-		};
-	};
-
-	video-receiver@70 {
-		compatible = "adi,adv7482";
-		reg = <0x70>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		interrupt-parent = <&gpio0>;
-		interrupt-names = "intrq1", "intrq2";
-		interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
-			     <17 IRQ_TYPE_LEVEL_LOW>;
-
-		port@7 {
-			reg = <7>;
-
-			adv7482_ain7: endpoint {
-				remote-endpoint = <&cvbs_con>;
-			};
-		};
-
-		port@8 {
-			reg = <8>;
-
-			adv7482_hdmi: endpoint {
-				remote-endpoint = <&hdmi_in_con>;
-			};
-		};
-
-		port@a {
-			reg = <10>;
-
-			adv7482_txa: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-				remote-endpoint = <&csi40_in>;
-			};
-		};
-	};
-};
-
-&i2c3 {
-	status = "okay";
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk-multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-
-	clock-frequency = <400000>;
-
-	pmic: pmic@30 {
-		pinctrl-0 = <&irq0_pins>;
-		pinctrl-names = "default";
-
-		compatible = "rohm,bd9571mwv";
-		reg = <0x30>;
-		interrupt-parent = <&intc_ex>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		rohm,ddr-backup-power = <0x1>;
-		rohm,rstbmode-level;
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&lvds0 {
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x13_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-
-	ports {
-		port@1 {
-			lvds0_out: endpoint {
-				remote-endpoint = <&thc63lvd1024_in>;
-			};
-		};
-	};
-};
-
-&lvds1 {
-	/*
-	 * Even though the LVDS1 output is not connected, the encoder must be
-	 * enabled to supply a pixel clock to the DU for the DPAD output when
-	 * LVDS0 is in use.
-	 */
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x13_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pfc {
-	avb_pins: avb {
-		groups = "avb_link", "avb_mii";
-		function = "avb";
-	};
-
-	canfd0_pins: canfd0 {
-		groups = "canfd0_data";
-		function = "canfd0";
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
-		function = "du";
-	};
-
-	irq0_pins: irq0 {
-		groups = "intc_ex_irq0";
-		function = "intc_ex";
-	};
-
-	keys_pins: keys {
-		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
-		bias-pull-up;
-	};
-
-	pwm3_pins: pwm3 {
-		groups = "pwm3_b";
-		function = "pwm3";
-	};
-
-	pwm5_pins: pwm5 {
-		groups = "pwm5_a";
-		function = "pwm5";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi1_pins: sd1 {
-		groups = "sdhi1_data4", "sdhi1_ctrl";
-		function = "sdhi1";
-		power-source = <3300>;
-	};
-
-	sdhi1_pins_uhs: sd1_uhs {
-		groups = "sdhi1_data4", "sdhi1_ctrl";
-		function = "sdhi1";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout1_a";
-		function = "audio_clk";
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
-		function = "ssi";
-	};
-
-	usb0_pins: usb {
-		groups = "usb0_b", "usb0_id";
-		function = "usb0";
-	};
-
-	usb30_pins: usb30 {
-		groups = "usb30";
-		function = "usb30";
-	};
-};
-
-&pwm3 {
-	pinctrl-0 = <&pwm3_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&pwm5 {
-	pinctrl-0 = <&pwm5_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
-		 <&cpg CPG_CORE R8A77990_CLK_ZA2>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0>, <&src0>, <&dvc0>;
-			capture  = <&ssi1>, <&src1>, <&dvc1>;
-		};
-	};
-
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi1 {
-	pinctrl-0 = <&sdhi1_pins>;
-	pinctrl-1 = <&sdhi1_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi1>;
-	vqmmc-supply = <&vccq_sdhi1>;
-	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi3 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	mmc-hs200-1_8v;
-	mmc-hs400-1_8v;
-	bus-width = <8>;
-	no-sd;
-	no-sdio;
-	non-removable;
-	full-pwr-cycle-in-suspend;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb3_peri0 {
-	companion = <&xhci0>;
-	status = "okay";
-};
-
-&vin4 {
-	status = "okay";
-};
-
-&vin5 {
-	status = "okay";
-};
-
-&xhci0 {
-	pinctrl-0 = <&usb30_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
 };

arch/arm64/boot/dts/renesas/r8a77995-draak.dts

···
 
 /dts-v1/;
 #include "r8a77995.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "draak.dtsi"
 
 / {
 	model = "Renesas Draak board based on r8a77995";
 	compatible = "renesas,draak", "renesas,r8a77995";
-
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <12288000>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
-
-		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
-		default-brightness-level = <10>;
-
-		power-supply = <&reg_12p0v>;
-		enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	composite-in {
-		compatible = "composite-video-connector";
-
-		port {
-			composite_con_in: endpoint {
-				remote-endpoint = <&adv7180_in>;
-			};
-		};
-	};
-
-	hdmi-in {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&adv7612_in>;
-			};
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_out: endpoint {
-				remote-endpoint = <&adv7511_out>;
-			};
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		pinctrl-0 = <&keys_pins>;
-		pinctrl-names = "default";
-
-		key-1 {
-			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_1>;
-			label = "SW56-1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-2 {
-			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_2>;
-			label = "SW56-2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-3 {
-			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_3>;
-			label = "SW56-3";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-4 {
-			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_4>;
-			label = "SW56-4";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-	};
-
-	lvds-decoder {
-		compatible = "thine,thc63lvd1024";
-		vcc-supply = <&reg_3p3v>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				thc63lvd1024_in: endpoint {
-					remote-endpoint = <&lvds0_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				thc63lvd1024_out: endpoint {
-					remote-endpoint = <&adv7511_in>;
-				};
-			};
-		};
-	};
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x18000000>;
-	};
-
-	reg_1p8v: regulator-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_12p0v: regulator-12p0v {
-		compatible = "regulator-fixed";
-		regulator-name = "D12.0V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	sound_card: sound {
-		compatible = "audio-graph-card";
-
-		dais = <&rsnd_port0	/* ak4613 */
-			/* HDMI is not yet supported */
-		>;
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <74250000>;
-	};
-
-	x19_clk: x19 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-};
-
-&audio_clk_b {
-	/*
-	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
-	 * and R-Car Sound uses AUDIO_CLKB.
-	 * Note is that schematic indicates VI4_FIELD conection only
-	 * not AUDIO_CLKB at SoC page.
-	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
-	 * SW60 should be 1-2.
-	 */
-
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb0_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
-		/*
-		 * TX clock internal delay mode is required for reliable
-		 * 1Gbps communication using the KSZ9031RNX phy present on
-		 * the Draak board, however, TX clock internal delay mode
-		 * isn't supported on r8a77995.  Thus, limit speed to
-		 * 100Mbps for reliable communication.
-		 */
-		max-speed = <100>;
-	};
-};
-
-&can0 {
-	pinctrl-0 = <&can0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-0 = <&can1_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 724>,
-		 <&cpg CPG_MOD 723>,
-		 <&x12_clk>;
-	clock-names = "du.0", "du.1", "dclkin.0";
-
-	ports {
-		port@0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-	};
-};
-
-&ehci0 {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <48000000>;
-};
-
-&hsusb {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-0 = <&i2c0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 0>; /* audio_clkout */
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-
-		port {
-			ak4613_endpoint: endpoint {
-				remote-endpoint = <&rsnd_for_ak4613>;
-			};
-		};
-	};
-
-	composite-in@20 {
-		compatible = "adi,adv7180cp";
-		reg = <0x20>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7180_in: endpoint {
-					remote-endpoint = <&composite_con_in>;
-				};
-			};
-
-			port@3 {
-				reg = <3>;
-
-				/*
-				 * The VIN4 video input path is shared between
-				 * CVBS and HDMI inputs through SW[49-53]
-				 * switches.
-				 *
-				 * CVBS is the default selection, link it to
-				 * VIN4 here.
-				 */
-				adv7180_out: endpoint {
-					remote-endpoint = <&vin4_in>;
-				};
-			};
-		};
-
-	};
-
-	hdmi-encoder@39 {
-		compatible = "adi,adv7511w";
-		reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
-		reg-names = "main", "edid", "cec", "packet";
-		interrupt-parent = <&gpio1>;
-		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511_in: endpoint {
-					remote-endpoint = <&thc63lvd1024_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con_out>;
-				};
-			};
-		};
-	};
-
-	hdmi-decoder@4c {
-		compatible = "adi,adv7612";
-		reg = <0x4c>;
-		default-input = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				adv7612_in: endpoint {
-					remote-endpoint = <&hdmi_con_in>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-
-				/*
-				 * The VIN4 video input path is shared between
-				 * CVBS and HDMI inputs through SW[49-53]
-				 * switches.
-				 *
-				 * CVBS is the default selection, leave HDMI
-				 * not connected here.
-				 */
-				adv7612_out: endpoint {
-					pclk-sample = <0>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-				};
-			};
-		};
-	};
-
-	cs2000: clk-multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&i2c1 {
-	pinctrl-0 = <&i2c1_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&lvds0 {
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x12_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-
-	ports {
-		port@1 {
-			lvds0_out: endpoint {
-				remote-endpoint = <&thc63lvd1024_in>;
-			};
-		};
-	};
-};
-
-&lvds1 {
-	/*
-	 * Even though the LVDS1 output is not connected, the encoder must be
-	 * enabled to supply a pixel clock to the DU for the DPAD output when
-	 * LVDS0 is in use.
-	 */
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x12_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&pfc {
-	avb0_pins: avb {
-		groups = "avb0_link", "avb0_mdio", "avb0_mii";
-		function = "avb0";
-	};
-
-	can0_pins: can0 {
-		groups = "can0_data_a";
-		function = "can0";
-	};
-
-	can1_pins: can1 {
-		groups = "can1_data_a";
-		function = "can1";
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
-		function = "du";
-	};
-
-	i2c0_pins: i2c0 {
-		groups = "i2c0";
-		function = "i2c0";
-	};
-
-	i2c1_pins: i2c1 {
-		groups = "i2c1";
-		function = "i2c1";
-	};
-
-	keys_pins: keys {
-		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
-		bias-pull-up;
-	};
-
-	pwm0_pins: pwm0 {
-		groups = "pwm0_c";
-		function = "pwm0";
-	};
-
-	pwm1_pins: pwm1 {
-		groups = "pwm1_c";
-		function = "pwm1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data";
-		function = "scif2";
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "mmc_data8", "mmc_ctrl";
-		function = "mmc";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "mmc_data8", "mmc_ctrl";
-		function = "mmc";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound-clk {
-		groups = "audio_clk_a", "audio_clk_b",
-			 "audio_clkout", "audio_clkout1";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	vin4_pins_cvbs: vin4 {
-		groups = "vin4_data8", "vin4_sync", "vin4_clk";
-		function = "vin4";
-	};
-};
-
-&pwm0 {
-	pinctrl-0 = <&pwm0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&pwm1 {
-	pinctrl-0 = <&pwm1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
-		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&cs2000>, <&audio_clk_b>,
-		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
-
-	ports {
-		rsnd_port0: port {
-			rsnd_for_ak4613: endpoint {
-				remote-endpoint = <&ak4613_endpoint>;
-				dai-format = "left_j";
-				bitclock-master = <&rsnd_for_ak4613>;
-				frame-master = <&rsnd_for_ak4613>;
-				playback = <&ssi3>, <&src5>, <&dvc0>;
-				capture  = <&ssi4>, <&src6>, <&dvc1>;
-			};
-		};
-	};
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	no-sd;
-	no-sdio;
-	non-removable;
-	status = "okay";
-};
-
-&ssi4 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	renesas,no-otg-pins;
-	status = "okay";
-};
-
-&vin4 {
-	pinctrl-0 = <&vin4_pins_cvbs>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	ports {
-		port {
-			vin4_in: endpoint {
-				remote-endpoint = <&adv7180_out>;
-			};
-		};
-	};
 };

arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi

···
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 
 #include "r8a779a0.dtsi"
···
 
 	chosen {
 		stdout-path = "serial0:115200n8";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW47";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-2 {
+			gpios = <&gpio6 19 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW48";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-3 {
+			gpios = <&gpio6 20 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW49";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
 	};
 
 	leds {
···
 	i2c6_pins: i2c6 {
 		groups = "i2c6";
 		function = "i2c6";
+	};
+
+	keys_pins: keys {
+		pins = "GP_6_18", "GP_6_19", "GP_6_20";
+		bias-pull-up;
 	};
 
 	mmc_pins: mmc {

arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio4>;

arch/arm64/boot/dts/renesas/r8a779a0.dtsi

···
 			status = "disabled";
 		};
 
+		tpu: pwm@e6e80000 {
+			compatible = "renesas,tpu-r8a779a0", "renesas,tpu";
+			reg = <0 0xe6e80000 0 0x148>;
+			interrupts = <GIC_SPI 515 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 718>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 718>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a779a0",
 				     "renesas,rcar-gen3-msiof";
···
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 706>;
 			max-frequency = <200000000>;
+			iommus = <&ipmmu_ds0 32>;
 			status = "disabled";
+		};
+
+		ipmmu_rt0: iommu@ee480000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xee480000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 10>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_rt1: iommu@ee4c0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xee4c0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 19>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds0: iommu@eed00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds1: iommu@eed40000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed40000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ir: iommu@eed80000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed80000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 3>;
+			power-domains = <&sysc R8A779A0_PD_A3IR>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vc0: iommu@eedc0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeedc0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 12>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vi0: iommu@eee80000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeee80000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 14>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vi1: iommu@eeec0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeeec0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 15>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_3dg: iommu@eee00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeee00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 6>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vip0: iommu@eef00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeef00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 5>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vip1: iommu@eef40000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeef40000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 11>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: iommu@eefc0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeefc0000 0 0x20000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
 		};
 
 		gic: interrupt-controller@f1000000 {

arch/arm64/boot/dts/renesas/r8a779m0.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3e (R8A779M0) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m0", "renesas,r8a7795";
+};

arch/arm64/boot/dts/renesas/r8a779m2.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3e (R8A779M2) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77961.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m2", "renesas,r8a77961";
+};

arch/arm64/boot/dts/renesas/r8a779m4.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3Ne (R8A779M4) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77965.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m4", "renesas,r8a77965";
+};

arch/arm64/boot/dts/renesas/r8a779m5-salvator-xs.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car M3Ne-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77965-salvator-xs.dts
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779m5.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a779m5";
+	compatible = "renesas,salvator-xs", "renesas,r8a779m5",
+		     "renesas,r8a77965";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 721>,
+		 <&versaclock6 1>,
+		 <&x21_clk>,
+		 <&versaclock6 2>;
+	clock-names = "du.0", "du.1", "du.3",
+		      "dclkin.0", "dclkin.1", "dclkin.3";
+};

arch/arm64/boot/dts/renesas/r8a779m5.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3Ne-2G (R8A779M5) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77965.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m5", "renesas,r8a77965";
+};

arch/arm64/boot/dts/renesas/r8a779m6.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car E3e (R8A779M6) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77990.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m6", "renesas,r8a77990";
+};

arch/arm64/boot/dts/renesas/r8a779m7.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car D3e (R8A779M7) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77995.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m7", "renesas,r8a77995";
+};

arch/arm64/boot/dts/renesas/r8a779m8.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3Ne (R8A779M8) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m8", "renesas,r8a7795";
+};

arch/arm64/boot/dts/renesas/r9a07g044.dtsi

···
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	audio_clk1: audio_clk1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	audio_clk2: audio_clk2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
···
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
+
+		ssi0: ssi@10049c00 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x10049c00 0 0x400>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 329 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI0_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI0_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI0_RST_M2_REG>;
+			dmas = <&dmac 0x2655>, <&dmac 0x2656>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi1: ssi@1004a000 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a000 0 0x400>;
+			interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 332 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 333 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI1_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI1_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI1_RST_M2_REG>;
+			dmas = <&dmac 0x2659>, <&dmac 0x265a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi2: ssi@1004a400 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a400 0 0x400>;
+			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 336 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 337 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI2_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI2_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI2_RST_M2_REG>;
+			dmas = <&dmac 0x265f>;
+			dma-names = "rt";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi3: ssi@1004a800 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a800 0 0x400>;
+			interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 341 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI3_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI3_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI3_RST_M2_REG>;
+			dmas = <&dmac 0x2661>, <&dmac 0x2662>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
 
 		scif0: serial@1004b800 {
 			compatible = "renesas,scif-r9a07g044";
···
 				 <&cpg R9A07G044_GPIO_SPARE_RESETN>;
 		};
 
+		dmac: dma-controller@11820000 {
+			compatible = "renesas,r9a07g044-dmac",
+				     "renesas,rz-dmac";
+			reg = <0 0x11820000 0 0x10000>,
+			      <0 0x11830000 0 0x10000>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD R9A07G044_DMAC_ACLK>,
+				 <&cpg CPG_MOD R9A07G044_DMAC_PCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_DMAC_ARESETN>,
+				 <&cpg R9A07G044_DMAC_RST_ASYNC>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
 		gic: interrupt-controller@11900000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
···
 			reg = <0x0 0x11900000 0 0x40000>,
 			      <0x0 0x11940000 0 0x60000>;
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+		};
+
+		phyrst: usbphy-ctrl@11c40000 {
+			compatible = "renesas,r9a07g044-usbphy-ctrl",
+				     "renesas,rzg2l-usbphy-ctrl";
+			reg = <0 0x11c40000 0 0x10000>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>;
+			resets = <&cpg R9A07G044_USB_PRESETN>;
+			power-domains = <&cpg>;
+			#reset-cells = <1>;
+			status = "disabled";
+		};
+
+		ohci0: usb@11c50000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c50000 0 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ohci1: usb@11c70000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c70000 0 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G044_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci0: usb@11c50100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c50100 0 0x100>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 2>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci1: usb@11c70100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c70100 0 0x100>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G044_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 2>;
+			phy-names = "usb";
+			companion = <&ohci1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy0: usb-phy@11c50200 {
+			compatible = "renesas,usb2-phy-r9a07g044",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c50200 0 0x700>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy1: usb-phy@11c70200 {
+			compatible = "renesas,usb2-phy-r9a07g044",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c70200 0 0x700>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		hsusb: usb@11c60000 {
+			compatible = "renesas,usbhs-r9a07g044",
+				     "renesas,rza2-usbhs";
+			reg = <0 0x11c60000 0 0x10000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2P_EXR_CPUCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2P_EXL_SYSRST>;
+			renesas,buswait = <7>;
+			phys = <&usb2_phy0 3>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
 		};
 	};
 

arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts

···
 
 /dts-v1/;
 #include "r9a07g044l2.dtsi"
+#include "rzg2l-smarc-som.dtsi"
 #include "rzg2l-smarc.dtsi"
 
 / {
 	model = "Renesas SMARC EVK based on r9a07g044l2";
 	compatible = "renesas,smarc-evk", "renesas,r9a07g044l2", "renesas,r9a07g044";
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x78000000>;
-	};
 };

arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2L SMARC SOM common parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/ {
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+};
+
+&adc {
+	pinctrl-0 = <&adc_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/delete-node/ channel@6;
+	/delete-node/ channel@7;
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+&pinctrl {
+	adc_pins: adc {
+		pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
+	};
+};

arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi

···
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * SSI-WM8978
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer cset name='Left Input Mixer L2 Switch' on
+ *	amixer cset name='Right Input Mixer R2 Switch' on
+ *	amixer cset name='Headphone Playback Volume' 100
+ *	amixer cset name='PCM Volume' 100%
+ *	amixer cset name='Input PGA Volume' 25
+ *
+ */
 
 / {
 	aliases {
 		serial0 = &scif0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c3 = &i2c3;
 	};
 
 	chosen {
 		bootargs = "ignore_loglevel";
 		stdout-path = "serial0:115200n8";
 	};
+
+	audio_mclock: audio_mclock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	snd_rzg2l: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&cpu_dai>;
+		simple-audio-card,frame-master = <&cpu_dai>;
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,widgets = "Microphone", "Microphone Jack";
+		simple-audio-card,routing =
+			    "L2", "Mic Bias",
+			    "R2", "Mic Bias",
+			    "Mic Bias", "Microphone Jack";
+
+		cpu_dai: simple-audio-card,cpu {
+			sound-dai = <&ssi0>;
+		};
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&audio_mclock>;
+			sound-dai = <&wm8978>;
+		};
+	};
+
+	usb0_vbus_otg: regulator-usb0-vbus-otg {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB0_VBUS_OTG";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
 };
 
-&extal_clk {
-	clock-frequency = <24000000>;
+&audio_clk1{
+	clock-frequency = <11289600>;
+};
+
+&audio_clk2{
+	clock-frequency = <12288000>;
+};
+
+&canfd {
+	pinctrl-0 = <&can0_pins &can1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+
+	channel1 {
+		status = "okay";
+	};
+};
+
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	wm8978: codec@1a {
+		compatible = "wlf,wm8978";
+		#sound-dai-cells = <0>;
+		reg = <0x1a>;
+	};
+};
+
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&phyrst {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-0 = <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	can0_pins: can0 {
+		pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
+	};
+
+	/* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
+	can0-stb {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can0_stb";
+	};
+
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
+	};
+
+	/* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
+	can1-stb {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can1_stb";
+	};
+
+	i2c0_pins: i2c0 {
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+		input-enable;
+	};
+
+	i2c1_pins: i2c1 {
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+		input-enable;
+	};
+
+	i2c3_pins: i2c3 {
+		pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
+			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
+			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
+	};
+
+	sound_clk_pins: sound_clk {
+		pins = "AUDIO_CLK1", "AUDIO_CLK2";
+		input-enable;
+	};
+
+	ssi0_pins: ssi0 {
+		pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
+			 <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
+			 <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
+			 <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
+	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
+	};
 };
 
 &scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ssi0 {
+	pinctrl-0 = <&ssi0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
 	status = "okay";
 };

arch/arm64/boot/dts/renesas/salvator-common.dtsi

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;

arch/arm64/boot/dts/renesas/ulcb.dtsi

···
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;