Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
net: clear heap allocation for ETHTOOL_GRXCLSRLALL
isdn: strcpy() => strlcpy()
Revert "mac80211: use netif_receive_skb in ieee80211_tx_status callpath"
mac80211: delete AddBA response timer
ath9k_hw: fix regression in ANI listen time calculation
caif: fix two caif_connect() bugs
bonding: fix WARN_ON when writing to bond_master sysfs file
skge: add quirk to limit DMA
MAINTAINERS: update Intel LAN Ethernet info
e1000e.txt: Add e1000e documentation
e1000.txt: Update e1000 documentation
ixgbevf.txt: Update ixgbevf documentation
cls_u32: signedness bug
Bluetooth: Disallow to change L2CAP_OPTIONS values when connected
sctp: Fix out-of-bounds reading in sctp_asoc_get_hmac()
sctp: prevent reading out-of-bounds memory
ipv4: correct IGMP behavior on v3 query during v2-compatibility mode
netdev: Depend on INET before selecting INET_LRO
Revert "ipv4: Make INET_LRO a bool instead of tristate."
net: Fix the condition passed to sk_wait_event()
...

Documentation/networking/e1000.txt

···
 Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
 ===============================================================
 
-September 26, 2006
-
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
 
 Contents
 ========
 
-- In This Release
 - Identifying Your Adapter
-- Building and Installation
 - Command Line Parameters
 - Speed and Duplex Configuration
 - Additional Configurations
-- Known Issues
 - Support
-
-
-In This Release
-===============
-
-This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters.  This driver includes support for Itanium(R)2-based systems.
-
-For questions related to hardware requirements, refer to the documentation
-supplied with your Intel PRO/1000 adapter. All hardware requirements listed
-apply to use with Linux.
-
-The following features are now available in supported kernels:
- - Native VLANs
- - Channel Bonding (teaming)
- - SNMP
-
-Channel Bonding documentation can be found in the Linux kernel source:
-/Documentation/networking/bonding.txt
-
-The driver information previously displayed in the /proc filesystem is not
-supported in this release.  Alternatively, you can use ethtool (version 1.6
-or later), lspci, and ifconfig to obtain the same information.
-
-Instructions on updating ethtool can be found in the section "Additional
-Configurations" later in this document.
-
-NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100
-support.
-
 
 Identifying Your Adapter
 ========================
···
 For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
-    http://support.intel.com/support/network/adapter/pro100/21397.htm
+    http://support.intel.com/support/go/network/adapter/idguide.htm
 
 For the latest Intel network drivers for Linux, refer to the following
 website.  In the search field, enter your adapter name or type, or use the
 networking link on the left to search for your adapter:
 
-    http://downloadfinder.intel.com/scripts-df/support_intel.asp
-
+    http://support.intel.com/support/go/network/adapter/home.htm
 
 Command Line Parameters
 =======================
-
-If the driver is built as a module, the  following optional parameters
-are used by entering them on the command line with the modprobe command
-using this syntax:
-
-     modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
-
-For example, with two PRO/1000 PCI adapters, entering:
-
-     modprobe e1000 TxDescriptors=80,128
-
-loads the e1000 driver with 80 TX descriptors for the first adapter and
-128 TX descriptors for the second adapter.
 
 The default value for each parameter is generally the recommended setting,
 unless otherwise noted.
···
         RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
         parameters, see the application note at:
         http://www.intel.com/design/network/applnots/ap450.htm
-
-        A descriptor describes a data buffer and attributes related to
-        the data buffer.  This information is accessed by the hardware.
-
 
 AutoNeg
 -------
···
 NOTE:  Refer to the Speed and Duplex section of this readme for more
        information on the AutoNeg parameter.
 
-
 Duplex
 ------
 (Supported only on adapters with copper connections)
···
 link partner is forced (either full or half), Duplex defaults to half-
 duplex.
 
-
 FlowControl
 -----------
 Valid Range:   0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
···
 This parameter controls the automatic generation(Tx) and response(Rx)
 to Ethernet PAUSE frames.
 
-
 InterruptThrottleRate
 ---------------------
 (not supported on Intel(R) 82542, 82543 or 82544-based adapters)
-Valid Range:   0,1,3,100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                   4=simplified balancing)
 Default Value: 3
 
 The driver can limit the amount of interrupts per second that the adapter
-will generate for incoming packets. It does this by writing a value to the 
-adapter that is based on the maximum amount of interrupts that the adapter 
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
 will generate per second.
 
 Setting InterruptThrottleRate to a value greater or equal to 100
···
 load on the system and can lower CPU utilization under heavy load,
 but will increase latency as packets are not processed as quickly.
 
-The default behaviour of the driver previously assumed a static 
-InterruptThrottleRate value of 8000, providing a good fallback value for 
-all traffic types,but lacking in small packet performance and latency. 
-The hardware can handle many more small packets per second however, and 
+The default behaviour of the driver previously assumed a static
+InterruptThrottleRate value of 8000, providing a good fallback value for
+all traffic types,but lacking in small packet performance and latency.
+The hardware can handle many more small packets per second however, and
 for this reason an adaptive interrupt moderation algorithm was implemented.
 
 Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which
-it dynamically adjusts the InterruptThrottleRate value based on the traffic 
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
 that it receives. After determining the type of incoming traffic in the last
-timeframe, it will adjust the InterruptThrottleRate to an appropriate value 
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
 for that traffic.
 
 The algorithm classifies the incoming traffic every interval into
-classes.  Once the class is determined, the InterruptThrottleRate value is 
-adjusted to suit that traffic type the best. There are three classes defined: 
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
 "Bulk traffic", for large amounts of packets of normal size; "Low latency",
 for small amounts of traffic and/or a significant percentage of small
-packets; and "Lowest latency", for almost completely small packets or 
+packets; and "Lowest latency", for almost completely small packets or
 minimal traffic.
 
-In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 
-for traffic that falls in class "Bulk traffic". If traffic falls in the "Low 
-latency" or "Lowest latency" class, the InterruptThrottleRate is increased 
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
 stepwise to 20000. This default mode is suitable for most applications.
 
 For situations where low latency is vital such as cluster or
 grid computing, the algorithm can reduce latency even more when
 InterruptThrottleRate is set to mode 1. In this mode, which operates
-the same as mode 3, the InterruptThrottleRate will be increased stepwise to 
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
 70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic.  If the bytes per second rate is approximately equal, the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
 
 Setting InterruptThrottleRate to 0 turns off any interrupt moderation
 and may improve small packet latency, but is generally not suitable
···
        be platform-specific.  If CPU utilization is not a concern, use
        RX_POLLING (NAPI) and default driver settings.
 
-
-
 RxDescriptors
 -------------
 Valid Range:   80-256 for 82542 and 82543-based adapters
···
 incoming packets, at the expense of increased system memory utilization.
 
 Each descriptor is 16 bytes.  A receive buffer is also allocated for each
-descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending 
+descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
 on the MTU setting. The maximum MTU size is 16110.
 
-NOTE:  MTU designates the frame size.  It only needs to be set for Jumbo 
-       Frames.  Depending on the available system resources, the request 
-       for a higher number of receive descriptors may be denied.  In this 
+NOTE:  MTU designates the frame size.  It only needs to be set for Jumbo
+       Frames.  Depending on the available system resources, the request
+       for a higher number of receive descriptors may be denied.  In this
        case, use a lower number.
-
 
 RxIntDelay
 ----------
···
           restoring the network connection.  To eliminate the potential
           for the hang ensure that RxIntDelay is set to 0.
 
-
 RxAbsIntDelay
 -------------
 (This parameter is supported only on 82540, 82545 and later adapters.)
···
 along with RxIntDelay, may improve traffic throughput in specific network
 conditions.
 
-
 Speed
 -----
 (This parameter is supported only on adapters with copper connections.)
···
 (Mbps).  If this parameter is not specified or is set to 0 and the link
 partner is set to auto-negotiate, the board will auto-detect the correct
 speed.  Duplex should also be set when Speed is set to either 10 or 100.
-
 
 TxDescriptors
 -------------
···
        higher number of transmit descriptors may be denied.  In this case,
        use a lower number.
 
+TxDescriptorStep
+----------------
+Valid Range:    1 (use every Tx Descriptor)
+		4 (use every 4th Tx Descriptor)
+
+Default Value:  1 (use every Tx Descriptor)
+
+On certain non-Intel architectures, it has been observed that intense TX
+traffic bursts of short packets may result in an improper descriptor
+writeback. If this occurs, the driver will report a "TX Timeout" and reset
+the adapter, after which the transmit flow will restart, though data may
+have stalled for as much as 10 seconds before it resumes.
+
+The improper writeback does not occur on the first descriptor in a system
+memory cache-line, which is typically 32 bytes, or 4 descriptors long.
+
+Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors
+are aligned to the start of a system memory cache line, and so this problem
+will not occur.
+
+NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of
+       TxDescriptors available for transmits to 1/4 of the normal allocation.
+       This has a possible negative performance impact, which may be
+       compensated for by allocating more descriptors using the TxDescriptors
+       module parameter.
+
+       There are other conditions which may result in "TX Timeout", which will
+       not be resolved by the use of the TxDescriptorStep parameter. As the
+       issue addressed by this parameter has never been observed on Intel
+       Architecture platforms, it should not be used on Intel platforms.
 
 TxIntDelay
 ----------
···
 efficiency if properly tuned for specific network traffic.  If the
 system is reporting dropped transmits, this value may be set too high
 causing the driver to run out of available transmit descriptors.
-
 
 TxAbsIntDelay
 -------------
···
 A value of '1' indicates that the driver should enable IP checksum
 offload for received packets (both UDP and TCP) to the adapter hardware.
 
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+Usage: insmod e1000.ko copybreak=128
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can turn off
+this parameter in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
 
 Speed and Duplex Configuration
 ==============================
···
 parameter should not be used.  Instead, use the Speed and Duplex parameters
 previously mentioned to force the adapter to the same speed and duplex.
 
-
 Additional Configurations
 =========================
-
-  Configuring the Driver on Different Distributions
-  -------------------------------------------------
-  Configuring a network driver to load properly when the system is started
-  is distribution dependent.  Typically, the configuration process involves
-  adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
-  as editing other system startup scripts and/or configuration files.  Many
-  popular Linux distributions ship with tools to make these changes for you.
-  To learn the proper way to configure a network device for your system,
-  refer to your distribution documentation.  If during this process you are
-  asked for the driver or module name, the name for the Linux Base Driver
-  for the Intel(R) PRO/1000 Family of Adapters is e1000.
-
-  As an example, if you install the e1000 driver for two PRO/1000 adapters
-  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
-  the following to modules.conf or or modprobe.conf:
-
-       alias eth0 e1000
-       alias eth1 e1000
-       options e1000 Speed=10,100 Duplex=2,1
-
-  Viewing Link Messages
-  ---------------------
-  Link messages will not be displayed to the console if the distribution is
-  restricting system messages.  In order to see network driver link messages
-  on your console, set dmesg to eight by entering the following:
-
-       dmesg -n 8
-
-  NOTE: This setting is not saved across reboots.
 
   Jumbo Frames
   ------------
···
    setting in a different location.
 
   Notes:
-
-  - To enable Jumbo Frames, increase the MTU size on the interface beyond
-    1500.
+  Degradation in throughput performance may be observed in some Jumbo frames
+  environments. If this is observed, increasing the application's socket buffer
+  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+  See the specific application manual and /usr/src/linux*/Documentation/
+  networking/ip-sysctl.txt for more details.
 
   - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
     with the maximum Jumbo Frames size of 16128.
···
   - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
     loss of link.
 
-  - Some Intel gigabit adapters that support Jumbo Frames have a frame size
-    limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
-    The adapters with this limitation are based on the Intel(R) 82571EB,
-    82572EI, 82573L and 80003ES2LAN controller.  These correspond to the
-    following product names:
-     Intel(R) PRO/1000 PT Server Adapter
-     Intel(R) PRO/1000 PT Desktop Adapter
-     Intel(R) PRO/1000 PT Network Connection
-     Intel(R) PRO/1000 PT Dual Port Server Adapter
-     Intel(R) PRO/1000 PT Dual Port Network Connection
-     Intel(R) PRO/1000 PF Server Adapter
-     Intel(R) PRO/1000 PF Network Connection
-     Intel(R) PRO/1000 PF Dual Port Server Adapter
-     Intel(R) PRO/1000 PB Server Connection
-     Intel(R) PRO/1000 PL Network Connection
-     Intel(R) PRO/1000 EB Network Connection with I/O Acceleration
-     Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration
-     Intel(R) PRO/1000 PT Quad Port Server Adapter
-
   - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
     support Jumbo Frames. These correspond to the following product names:
      Intel(R) PRO/1000 Gigabit Server Adapter
      Intel(R) PRO/1000 PM Network Connection
-
-  - The following adapters do not support Jumbo Frames:
-     Intel(R) 82562V 10/100 Network Connection
-     Intel(R) 82566DM Gigabit Network Connection
-     Intel(R) 82566DC Gigabit Network Connection
-     Intel(R) 82566MM Gigabit Network Connection
-     Intel(R) 82566MC Gigabit Network Connection
-     Intel(R) 82562GT 10/100 Network Connection
-     Intel(R) 82562G 10/100 Network Connection
-
 
   Ethtool
   -------
···
   The latest release of ethtool can be found from
   http://sourceforge.net/projects/gkernel.
 
-  NOTE: Ethtool 1.6 only supports a limited set of ethtool options.  Support
-  for a more complete ethtool feature set can be enabled by upgrading
-  ethtool to ethtool-1.8.1.
-
   Enabling Wake on LAN* (WoL)
   ---------------------------
-  WoL is configured through the Ethtool* utility.  Ethtool is included with
-  all versions of Red Hat after Red Hat 7.2.  For other Linux distributions,
-  download and install Ethtool from the following website:
-  http://sourceforge.net/projects/gkernel.
-
-  For instructions on enabling WoL with Ethtool, refer to the website listed
-  above.
+  WoL is configured through the Ethtool* utility.
 
   WoL will be enabled on the system during the next shut down or reboot.
   For this driver version, in order to enable WoL, the e1000 driver must be
   loaded when shutting down or rebooting the system.
-
-  Wake On LAN is only supported on port A for the following devices:
-  Intel(R) PRO/1000 PT Dual Port Network Connection
-  Intel(R) PRO/1000 PT Dual Port Server Connection
-  Intel(R) PRO/1000 PT Dual Port Server Adapter
-  Intel(R) PRO/1000 PF Dual Port Server Adapter
-  Intel(R) PRO/1000 PT Quad Port Server Adapter
-
-  NAPI
-  ----
-  NAPI (Rx polling mode) is enabled in the e1000 driver.
-
-  See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
-
-
-Known Issues
-============
-
-Dropped Receive Packets on Half-duplex 10/100 Networks
-------------------------------------------------------
-If you have an Intel PCI Express adapter running at 10mbps or 100mbps, half-
-duplex, you may observe occasional dropped receive packets.  There are no
-workarounds for this problem in this network configuration.  The network must
-be updated to operate in full-duplex, and/or 1000mbps only.
-
-Jumbo Frames System Requirement
--------------------------------
-Memory allocation failures have been observed on Linux systems with 64 MB
-of RAM or less that are running Jumbo Frames.  If you are using Jumbo
-Frames, your system may require more than the advertised minimum
-requirement of 64 MB of system memory.
-
-Performance Degradation with Jumbo Frames
------------------------------------------
-Degradation in throughput performance may be observed in some Jumbo frames
-environments.  If this is observed, increasing the application's socket
-buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
-may help.  See the specific application manual and
-/usr/src/linux*/Documentation/
-networking/ip-sysctl.txt for more details.
-
-Jumbo Frames on Foundry BigIron 8000 switch
--------------------------------------------
-There is a known issue using Jumbo frames when connected to a Foundry
-BigIron 8000 switch.  This is a 3rd party limitation.  If you experience
-loss of packets, lower the MTU size.
-
-Allocating Rx Buffers when Using Jumbo Frames 
----------------------------------------------
-Allocating Rx buffers when using Jumbo Frames on 2.6.x kernels may fail if 
-the available memory is heavily fragmented. This issue may be seen with PCI-X 
-adapters or with packet split disabled. This can be reduced or eliminated 
-by changing the amount of available memory for receive buffer allocation, by
-increasing /proc/sys/vm/min_free_kbytes. 
-
-Multiple Interfaces on Same Ethernet Broadcast Network
-------------------------------------------------------
-Due to the default ARP behavior on Linux, it is not possible to have
-one system on two IP networks in the same Ethernet broadcast domain
-(non-partitioned switch) behave as expected.  All Ethernet interfaces
-will respond to IP traffic for any IP address assigned to the system.
-This results in unbalanced receive traffic.
-
-If you have multiple interfaces in a server, either turn on ARP
-filtering by entering:
-
-    echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-(this only works if your kernel's version is higher than 2.4.5),
-
-NOTE: This setting is not saved across reboots.  The configuration
-change can be made permanent by adding the line:
-    net.ipv4.conf.all.arp_filter = 1
-to the file /etc/sysctl.conf
-
-      or,
-
-install the interfaces in separate broadcast domains (either in
-different switches or in a switch partitioned to VLANs).
-
-82541/82547 can't link or are slow to link with some link partners
------------------------------------------------------------------
-There is a known compatibility issue with 82541/82547 and some
-low-end switches where the link will not be established, or will
-be slow to establish.  In particular, these switches are known to
-be incompatible with 82541/82547:
-
-    Planex FXG-08TE
-    I-O Data ETG-SH8
-
-To workaround this issue, the driver can be compiled with an override
-of the PHY's master/slave setting.  Forcing master or forcing slave
-mode will improve time-to-link.
-
-    # make CFLAGS_EXTRA=-DE1000_MASTER_SLAVE=<n>
-
-Where <n> is:
-
-    0 = Hardware default
-    1 = Master mode
-    2 = Slave mode
-    3 = Auto master/slave
-
-Disable rx flow control with ethtool
-------------------------------------
-In order to disable receive flow control using ethtool, you must turn
-off auto-negotiation on the same command line.
-
-For example:
-
-   ethtool -A eth? autoneg off rx off
-
-Unplugging network cable while ethtool -p is running
-----------------------------------------------------
-In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging
-the network cable while ethtool -p is running will cause the system to
-become unresponsive to keyboard commands, except for control-alt-delete.
-Restarting the system appears to be the only remedy.
-
 
 Support
 =======

Documentation/networking/e1000e.txt

···
+Linux* Driver for Intel(R) Network Connection
+===============================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Additional Configurations
+- Support
+
+Identifying Your Adapter
+========================
+
+The e1000e driver supports all PCI Express Intel(R) Gigabit Network
+Connections, except those that are 82575, 82576 and 82580-based*.
+
+* NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter is supported by
+  the e1000 driver, not the e1000e driver due to the 82546 part being used
+  behind a PCI Express bridge.
+
+For more information on how to identify your adapter, go to the Adapter &
+Driver ID Guide at:
+
+    http://support.intel.com/support/go/network/adapter/idguide.htm
+
+For the latest Intel network drivers for Linux, refer to the following
+website.  In the search field, enter your adapter name or type, or use the
+networking link on the left to search for your adapter:
+
+    http://support.intel.com/support/go/network/adapter/home.htm
+
+Command Line Parameters
+=======================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTES:  For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
+        http://www.intel.com/design/network/applnots/ap450.htm
+
+InterruptThrottleRate
+---------------------
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                   4=simplified balancing)
+Default Value: 3
+
+The driver can limit the amount of interrupts per second that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
+will generate per second.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+stepwise to 20000. This default mode is suitable for most applications.
+
+For situations where low latency is vital such as cluster or
+grid computing, the algorithm can reduce latency even more when
+InterruptThrottleRate is set to mode 1. In this mode, which operates
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic.  If the bytes per second rate is approximately equal the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
+Setting InterruptThrottleRate to 0 turns off any interrupt moderation
+and may improve small packet latency, but is generally not suitable
+for bulk throughput traffic.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+       RxAbsIntDelay parameters.  In other words, minimizing the receive
+       and/or transmit absolute delays does not force the controller to
+       generate more interrupts than what the Interrupt Throttle Rate
+       allows.
+
+NOTE:  When e1000e is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly.  In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
+
+           modprobe e1000e InterruptThrottleRate=3000,3000,3000
+
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver.  The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific.  If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
+RxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic.  Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic.  If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
+          hang (stop transmitting) under certain network conditions.  If
+          this occurs a NETDEV WATCHDOG message is logged in the system
+          event log.  In addition, the controller is automatically reset,
+          restoring the network connection.  To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated.  Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+TxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds.  Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic.  If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 32
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated.  Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000e/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can set this parameter
+in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
+
+IntMode
+-------
+Valid Range: 0-2 (0=legacy, 1=MSI, 2=MSI-X)
+Default Value: 2
+
+Allows changing the interrupt mode at module load time, without requiring a
+recompile. If the driver load fails to enable a specific interrupt mode, the
+driver will try other interrupt modes, from least to most compatible.  The
+interrupt order is MSI-X, MSI, Legacy.  If specifying MSI (IntMode=1)
+interrupts, only MSI and Legacy will be attempted.
+
+CrcStripping
+------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Strip the CRC from received packets before sending up the network stack.  If
+you have a machine with a BMC enabled but cannot receive IPMI traffic after
+loading or enabling the driver, try disabling this feature.
+
+WriteProtectNVM
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Set the hardware to ignore all write/erase cycles to the GbE region in the
+ICHx NVM (non-volatile memory).  This feature can be disabled by the
+WriteProtectNVM module parameter (enabled by default) only after a hardware
+reset, but the machine must be power cycled before trying to enable writes.
+
+Note: the kernel boot option iomem=relaxed may need to be set if the kernel
+config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the
+NVM from user space via ethtool.
+
+Additional Configurations
+=========================
+
+  Jumbo Frames
+  ------------
+  Jumbo Frames support is enabled by changing the MTU to a value larger than
+  the default of 1500.  Use the ifconfig command to increase the MTU size.
+  For example:
+
+       ifconfig eth<x> mtu 9000 up
+
+  This setting is not saved across reboots.
+
+  Notes:
+
+  - The maximum MTU setting for Jumbo Frames is 9216.  This value coincides
+    with the maximum Jumbo Frames size of 9234 bytes.
+
+  - Using Jumbo Frames at 10 or 100 Mbps is not supported and may result in
+    poor performance or loss of link.
+
+  - Some adapters limit Jumbo Frames sized packets to a maximum of
+    4096 bytes and some adapters do not support Jumbo Frames.
+
+
+  Ethtool
+  -------
+  The driver utilizes the ethtool interface for driver configuration and
+  diagnostics, as well as displaying statistical information.  We
+  strongly recommend downloading the latest version of Ethtool at:
+
+  http://sourceforge.net/projects/gkernel.
+
+  Speed and Duplex
+  ----------------
+  Speed and Duplex are configured through the Ethtool* utility. For
+  instructions,  refer to the Ethtool man page.
+
+  Enabling Wake on LAN* (WoL)
+  ---------------------------
+  WoL is configured through the Ethtool* utility. For instructions on
+  enabling WoL with Ethtool, refer to the Ethtool man page.
+
+  WoL will be enabled on the system during the next shut down or reboot.
+  For this driver version, in order to enable WoL, the e1000e driver must be
+  loaded when shutting down or rebooting the system.
+
+  In most cases Wake On LAN is only supported on port A for multiple port
+  adapters. To verify if a port supports Wake on LAN run ethtool eth<X>.
+
+
+Support
+=======
+
+For general information, go to the Intel support website at:
+
+    www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related
+to the issue to [e-mail]

Documentation/networking/ixgbevf.txt

···
 Linux* Base Driver for Intel(R) Network Connection
 ==================================================
 
-November 24, 2009
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
 
 Contents
 ========
 
-- In This Release
 - Identifying Your Adapter
 - Known Issues/Troubleshooting
 - Support
-
-In This Release
-===============
 
 This file describes the ixgbevf Linux* Base Driver for Intel Network
 Connection.
···
 For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
-    http://support.intel.com/support/network/sb/CS-008441.htm
+    http://support.intel.com/support/go/network/adapter/idguide.htm
 
 Known Issues/Troubleshooting
 ============================
···
 If an issue is identified with the released source code on the supported
 kernel with a supported adapter, email the specific information related
 to the issue to [e-mail]
-
-License
-=======
-
-Intel 10 Gigabit Linux driver.
-Copyright(c) 1999 - 2009 Intel Corporation.
-
-This program is free software; you can redistribute it and/or modify it
-under the terms and conditions of the GNU General Public License,
-version 2, as published by the Free Software Foundation.
-
-This program is distributed in the hope it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along with
-this program; if not, write to the Free Software Foundation, Inc.,
-51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
-
-The full GNU General Public License is included in this distribution in
-the file called "COPYING".
-
-Trademarks
-==========
-
-Intel, Itanium, and Pentium are trademarks or registered trademarks of
-Intel Corporation or its subsidiaries in the United States and other
-countries.
-
-* Other names and brands may be claimed as the property of others.

MAINTAINERS

···
 S:	Maintained
 F:	drivers/net/ixp2000/
 
-INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe)
+INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe/ixgbevf)
 M:	Jeff Kirsher <[e-mail]>
 M:	Jesse Brandeburg <[e-mail]>
 M:	Bruce Allan <[e-mail]>
-M:	Alex Duyck <[e-mail]>
+M:	Carolyn Wyborny <[e-mail]>
+M:	Don Skidmore <[e-mail]>
+M:	Greg Rose <[e-mail]>
 M:	PJ Waskiewicz <[e-mail]>
+M:	Alex Duyck <[e-mail]>
 M:	John Ronciak <[e-mail]>
 L:	[e-mail]
 W:	http://e1000.sourceforge.net/
 S:	Supported
+F:	Documentation/networking/e100.txt
+F:	Documentation/networking/e1000.txt
+F:	Documentation/networking/e1000e.txt
+F:	Documentation/networking/igb.txt
+F:	Documentation/networking/igbvf.txt
+F:	Documentation/networking/ixgb.txt
+F:	Documentation/networking/ixgbe.txt
+F:	Documentation/networking/ixgbevf.txt
 F:	drivers/net/e100.c
 F:	drivers/net/e1000/
 F:	drivers/net/e1000e/
···
 F:	drivers/net/igbvf/
 F:	drivers/net/ixgb/
 F:	drivers/net/ixgbe/
+F:	drivers/net/ixgbevf/
 
 INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT
 L:	[e-mail]

drivers/isdn/sc/interrupt.c

···
 			}
 			else if(callid>=0x0000 && callid<=0x7FFF)
 			{
+				int len;
+
 				pr_debug("%s: Got Incoming Call\n",
 						sc_adapter[card]->devicename);
-				strcpy(setup.phone,&(rcvmsg.msg_data.byte_array[4]));
-				strcpy(setup.eazmsn,
-					sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn);
+				len = strlcpy(setup.phone, &(rcvmsg.msg_data.byte_array[4]),
+						sizeof(setup.phone));
+				if (len >= sizeof(setup.phone))
+					continue;
+				len = strlcpy(setup.eazmsn,
+						sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+						sizeof(setup.eazmsn));
+				if (len >= sizeof(setup.eazmsn))
+					continue;
 				setup.si1 = 7;
 				setup.si2 = 0;
 				setup.plan = 0;
···
 		 * Handle a GetMyNumber Rsp
 		 */
 		if (IS_CE_MESSAGE(rcvmsg,Call,0,GetMyNumber)){
-			strcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn,rcvmsg.msg_data.byte_array);
+			strlcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+				rcvmsg.msg_data.byte_array,
+				sizeof(rcvmsg.msg_data.byte_array));
 			continue;
 		}
 			

drivers/net/Kconfig

···
 
 config MV643XX_ETH
 	tristate "Marvell Discovery (643XX) and Orion ethernet support"
-	depends on MV64X60 || PPC32 || PLAT_ORION
+	depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
 	select INET_LRO
 	select PHYLIB
 	help
···
 
 config PASEMI_MAC
 	tristate "PA Semi 1/10Gbit MAC"
-	depends on PPC_PASEMI && PCI
+	depends on PPC_PASEMI && PCI && INET
 	select PHYLIB
 	select INET_LRO
 	help

drivers/net/bonding/bond_main.c

···
 		res = dev_alloc_name(bond_dev, "bond%d");
 		if (res < 0)
 			goto out;
+	} else {
+		/*
+		 * If we're given a name to register
+		 * we need to ensure that its not already
+		 * registered
+		 */
+		res = -EEXIST;
+		if (__dev_get_by_name(net, name) != NULL)
+			goto out;
 	}
 
 	res = register_netdevice(bond_dev);

drivers/net/skge.c

···
 #include <linux/seq_file.h>
 #include <linux/mii.h>
 #include <linux/slab.h>
+#include <linux/dmi.h>
 #include <asm/irq.h>
 
 #include "skge.h"
···
 	netif_info(skge, probe, skge->netdev, "addr %pM\n", dev->dev_addr);
 }
 
+static int only_32bit_dma;
+
 static int __devinit skge_probe(struct pci_dev *pdev,
 				const struct pci_device_id *ent)
 {
···
 
 	pci_set_master(pdev);
 
-	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+	if (!only_32bit_dma && !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
 		using_dac = 1;
 		err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
 	} else if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
···
 	.shutdown =	skge_shutdown,
 };
 
+static struct dmi_system_id skge_32bit_dma_boards[] = {
+	{
+		.ident = "Gigabyte nForce boards",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co"),
+			DMI_MATCH(DMI_BOARD_NAME, "nForce"),
+		},
+	},
+	{}
+};
+
 static int __init skge_init_module(void)
 {
+	if (dmi_check_system(skge_32bit_dma_boards))
+		only_32bit_dma = 1;
 	skge_debug_init();
 	return pci_register_driver(&skge_driver);
 }

drivers/net/wireless/ath/ath9k/ani.c

···
 	if (conf_is_ht40(conf))
 		return clockrate * 2;
 
-	return clockrate * 2;
+	return clockrate;
 }
 
 static int32_t ath9k_hw_ani_get_listen_time(struct ath_hw *ah)

include/net/bluetooth/bluetooth.h

···
 {
 	struct sk_buff *skb;
 
+	release_sock(sk);
 	if ((skb = sock_alloc_send_skb(sk, len + BT_SKB_RESERVE, nb, err))) {
 		skb_reserve(skb, BT_SKB_RESERVE);
 		bt_cb(skb)->incoming  = 0;
 	}
+	lock_sock(sk);
+
+	if (!skb && *err)
+		return NULL;
+
+	*err = sock_error(sk);
+	if (*err)
+		goto out;
+
+	if (sk->sk_shutdown) {
+		*err = -ECONNRESET;
+		goto out;
+	}
 
 	return skb;
+
+out:
+	kfree_skb(skb);
+	return NULL;
 }
 
 int bt_err(__u16 code);

net/bluetooth/l2cap.c

···
 
 static void l2cap_streaming_send(struct sock *sk)
 {
-	struct sk_buff *skb, *tx_skb;
+	struct sk_buff *skb;
 	struct l2cap_pinfo *pi = l2cap_pi(sk);
 	u16 control, fcs;
 
-	while ((skb = sk->sk_send_head)) {
-		tx_skb = skb_clone(skb, GFP_ATOMIC);
-
-		control = get_unaligned_le16(tx_skb->data + L2CAP_HDR_SIZE);
+	while ((skb = skb_dequeue(TX_QUEUE(sk)))) {
+		control = get_unaligned_le16(skb->data + L2CAP_HDR_SIZE);
 		control |= pi->next_tx_seq << L2CAP_CTRL_TXSEQ_SHIFT;
-		put_unaligned_le16(control, tx_skb->data + L2CAP_HDR_SIZE);
+		put_unaligned_le16(control, skb->data + L2CAP_HDR_SIZE);
 
 		if (pi->fcs == L2CAP_FCS_CRC16) {
-			fcs = crc16(0, (u8 *)tx_skb->data, tx_skb->len - 2);
-			put_unaligned_le16(fcs, tx_skb->data + tx_skb->len - 2);
+			fcs = crc16(0, (u8 *)skb->data, skb->len - 2);
+			put_unaligned_le16(fcs, skb->data + skb->len - 2);
 		}
 
-		l2cap_do_send(sk, tx_skb);
+		l2cap_do_send(sk, skb);
 
 		pi->next_tx_seq = (pi->next_tx_seq + 1) % 64;
-
-		if (skb_queue_is_last(TX_QUEUE(sk), skb))
-			sk->sk_send_head = NULL;
-		else
-			sk->sk_send_head = skb_queue_next(TX_QUEUE(sk), skb);
-
-		skb = skb_dequeue(TX_QUEUE(sk));
-		kfree_skb(skb);
 	}
 }
 
···
 
 	switch (optname) {
 	case L2CAP_OPTIONS:
+		if (sk->sk_state == BT_CONNECTED) {
+			err = -EINVAL;
+			break;
+		}
+
 		opts.imtu     = l2cap_pi(sk)->imtu;
 		opts.omtu     = l2cap_pi(sk)->omtu;
 		opts.flush_to = l2cap_pi(sk)->flush_to;
···
 		case L2CAP_CONF_MTU:
 			if (val < L2CAP_DEFAULT_MIN_MTU) {
 				*result = L2CAP_CONF_UNACCEPT;
-				pi->omtu = L2CAP_DEFAULT_MIN_MTU;
+				pi->imtu = L2CAP_DEFAULT_MIN_MTU;
 			} else
-				pi->omtu = val;
-			l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->omtu);
+				pi->imtu = val;
+			l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->imtu);
 			break;
 
 		case L2CAP_CONF_FLUSH_TO:
···
 	return 0;
 }
 
+static inline void set_default_fcs(struct l2cap_pinfo *pi)
+{
+	/* FCS is enabled only in ERTM or streaming mode, if one or both
+	 * sides request it.
+	 */
+	if (pi->mode != L2CAP_MODE_ERTM && pi->mode != L2CAP_MODE_STREAMING)
+		pi->fcs = L2CAP_FCS_NONE;
+	else if (!(pi->conf_state & L2CAP_CONF_NO_FCS_RECV))
+		pi->fcs = L2CAP_FCS_CRC16;
+}
+
 static inline int l2cap_config_req(struct l2cap_conn *conn, struct l2cap_cmd_hdr *cmd, u16 cmd_len, u8 *data)
 {
 	struct l2cap_conf_req *req = (struct l2cap_conf_req *) data;
···
 	if (!sk)
 		return -ENOENT;
 
-	if (sk->sk_state != BT_CONFIG) {
-		struct l2cap_cmd_rej rej;
-
-		rej.reason = cpu_to_le16(0x0002);
-		l2cap_send_cmd(conn, cmd->ident, L2CAP_COMMAND_REJ,
-				sizeof(rej), &rej);
+	if (sk->sk_state == BT_DISCONN)
 		goto unlock;
-	}
 
 	/* Reject if config buffer is too small. */
 	len = cmd_len - sizeof(*req);
···
 		goto unlock;
 
 	if (l2cap_pi(sk)->conf_state & L2CAP_CONF_INPUT_DONE) {
-		if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
-		    l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
-			l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+		set_default_fcs(l2cap_pi(sk));
 
 		sk->sk_state = BT_CONNECTED;
 
···
 	l2cap_pi(sk)->conf_state |= L2CAP_CONF_INPUT_DONE;
 
 	if (l2cap_pi(sk)->conf_state & L2CAP_CONF_OUTPUT_DONE) {
-		if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
-		    l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
-			l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+		set_default_fcs(l2cap_pi(sk));
 
 		sk->sk_state = BT_CONNECTED;
 		l2cap_pi(sk)->next_tx_seq = 0;

net/bluetooth/rfcomm/sock.c

···
 static void rfcomm_sk_state_change(struct rfcomm_dlc *d, int err)
 {
 	struct sock *sk = d->owner, *parent;
+	unsigned long flags;
+
 	if (!sk)
 		return;
 
 	BT_DBG("dlc %p state %ld err %d", d, d->state, err);
 
+	local_irq_save(flags);
 	bh_lock_sock(sk);
 
 	if (err)
···
 	}
 
 	bh_unlock_sock(sk);
+	local_irq_restore(flags);
 
 	if (parent && sock_flag(sk, SOCK_ZAPPED)) {
 		/* We have to drop DLC lock here, otherwise

net/caif/caif_socket.c

···
 	long timeo;
 	int err;
 	int ifindex, headroom, tailroom;
+	unsigned int mtu;
 	struct net_device *dev;
 
 	lock_sock(sk);
···
 		cf_sk->sk.sk_state = CAIF_DISCONNECTED;
 		goto out;
 	}
-	dev = dev_get_by_index(sock_net(sk), ifindex);
+
+	err = -ENODEV;
+	rcu_read_lock();
+	dev = dev_get_by_index_rcu(sock_net(sk), ifindex);
+	if (!dev) {
+		rcu_read_unlock();
+		goto out;
+	}
 	cf_sk->headroom = LL_RESERVED_SPACE_EXTRA(dev, headroom);
+	mtu = dev->mtu;
+	rcu_read_unlock();
+
 	cf_sk->tailroom = tailroom;
-	cf_sk->maxframe = dev->mtu - (headroom + tailroom);
-	dev_put(dev);
+	cf_sk->maxframe = mtu - (headroom + tailroom);
 	if (cf_sk->maxframe < 1) {
-		pr_warning("CAIF: %s(): CAIF Interface MTU too small (%d)\n",
-			__func__, dev->mtu);
-		err = -ENODEV;
+		pr_warning("CAIF: %s(): CAIF Interface MTU too small (%u)\n",
+			   __func__, mtu);
 		goto out;
 	}
 

net/core/ethtool.c

···
 	if (info.cmd == ETHTOOL_GRXCLSRLALL) {
 		if (info.rule_cnt > 0) {
 			if (info.rule_cnt <= KMALLOC_MAX_SIZE / sizeof(u32))
-				rule_buf = kmalloc(info.rule_cnt * sizeof(u32),
+				rule_buf = kzalloc(info.rule_cnt * sizeof(u32),
 						   GFP_USER);
 			if (!rule_buf)
 				return -ENOMEM;

net/core/stream.c

···
 
 		set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
 		sk->sk_write_pending++;
-		sk_wait_event(sk, &current_timeo, !sk->sk_err &&
-						  !(sk->sk_shutdown & SEND_SHUTDOWN) &&
-						  sk_stream_memory_free(sk) &&
-						  vm_wait);
+		sk_wait_event(sk, &current_timeo, sk->sk_err ||
+						  (sk->sk_shutdown & SEND_SHUTDOWN) ||
+						  (sk_stream_memory_free(sk) &&
+						  !vm_wait));
 		sk->sk_write_pending--;
 
 		if (vm_wait) {

net/ipv4/Kconfig

···
 	  If unsure, say Y.
 
 config INET_LRO
-	bool "Large Receive Offload (ipv4/tcp)"
+	tristate "Large Receive Offload (ipv4/tcp)"
 	default y
 	---help---
 	  Support for Large Receive Offload (ipv4/tcp).

net/ipv4/igmp.c

···
 	int			mark = 0;
 
 
-	if (len == 8 || IGMP_V2_SEEN(in_dev)) {
+	if (len == 8) {
 		if (ih->code == 0) {
 			/* Alas, old v1 router presents here. */
 
···
 		igmpv3_clear_delrec(in_dev);
 	} else if (len < 12) {
 		return;	/* ignore bogus packet; freed by caller */
+	} else if (IGMP_V1_SEEN(in_dev)) {
+		/* This is a v3 query with v1 queriers present */
+		max_delay = IGMP_Query_Response_Interval;
+		group = 0;
+	} else if (IGMP_V2_SEEN(in_dev)) {
+		/* this is a v3 query with v2 queriers present;
+		 * Interpretation of the max_delay code is problematic here.
+		 * A real v2 host would use ih_code directly, while v3 has a
+		 * different encoding. We use the v3 encoding as more likely
+		 * to be intended in a v3 query.
+		 */
+		max_delay = IGMPV3_MRC(ih3->code)*(HZ/IGMP_TIMER_SCALE);
 	} else { /* v3 */
 		if (!pskb_may_pull(skb, sizeof(struct igmpv3_query)))
 			return;

net/ipv6/route.c

···
  *	i.e. Path MTU discovery
  */
 
-void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
-			struct net_device *dev, u32 pmtu)
+static void rt6_do_pmtu_disc(struct in6_addr *daddr, struct in6_addr *saddr,
+			     struct net *net, u32 pmtu, int ifindex)
 {
 	struct rt6_info *rt, *nrt;
-	struct net *net = dev_net(dev);
 	int allfrag = 0;
 
-	rt = rt6_lookup(net, daddr, saddr, dev->ifindex, 0);
+	rt = rt6_lookup(net, daddr, saddr, ifindex, 0);
 	if (rt == NULL)
 		return;
 
···
 	}
 out:
 	dst_release(&rt->dst);
+}
+
+void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
+			struct net_device *dev, u32 pmtu)
+{
+	struct net *net = dev_net(dev);
+
+	/*
+	 * RFC 1981 states that a node "MUST reduce the size of the packets it
+	 * is sending along the path" that caused the Packet Too Big message.
+	 * Since it's not possible in the general case to determine which
+	 * interface was used to send the original packet, we update the MTU
+	 * on the interface that will be used to send future packets. We also
+	 * update the MTU on the interface that received the Packet Too Big in
+	 * case the original packet was forced out that interface with
+	 * SO_BINDTODEVICE or similar. This is the next best thing to the
+	 * correct behaviour, which would be to update the MTU on all
+	 * interfaces.
+	 */
+	rt6_do_pmtu_disc(daddr, saddr, net, pmtu, 0);
+	rt6_do_pmtu_disc(daddr, saddr, net, pmtu, dev->ifindex);
 }
 
 /*

net/mac80211/agg-tx.c

···
 
 	set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
 
+	del_timer_sync(&tid_tx->addba_resp_timer);
+
 	/*
 	 * After this packets are no longer handed right through
 	 * to the driver but are put onto tid_tx->pending instead,

net/mac80211/status.c

···
 				skb2 = skb_clone(skb, GFP_ATOMIC);
 				if (skb2) {
 					skb2->dev = prev_dev;
-					netif_receive_skb(skb2);
+					netif_rx(skb2);
 				}
 			}
 
···
 	}
 	if (prev_dev) {
 		skb->dev = prev_dev;
-		netif_receive_skb(skb);
+		netif_rx(skb);
 		skb = NULL;
 	}
 	rcu_read_unlock();

net/sched/cls_u32.c

···
 			int toff = off + key->off + (off2 & key->offmask);
 			__be32 *data, _data;
 
-			if (skb_headroom(skb) + toff < 0)
+			if (skb_headroom(skb) + toff > INT_MAX)
 				goto out;
 
 			data = skb_header_pointer(skb, toff, 4, &_data);

net/sctp/auth.c

···
 		id = ntohs(hmacs->hmac_ids[i]);
 
 		/* Check the id is in the supported range */
-		if (id > SCTP_AUTH_HMAC_ID_MAX)
+		if (id > SCTP_AUTH_HMAC_ID_MAX) {
+			id = 0;
 			continue;
+		}
 
 		/* See is we support the id.  Supported IDs have name and
 		 * length fields set, so that we can allocated and use
 		 * them.  We can safely just check for name, for without the
 		 * name, we can't allocate the TFM.
 		 */
-		if (!sctp_hmac_list[id].hmac_name)
+		if (!sctp_hmac_list[id].hmac_name) {
+			id = 0;
 			continue;
+		}
 
 		break;
 	}

net/sctp/socket.c

···
 	/* Walk through the addrs buffer and count the number of addresses. */
 	addr_buf = kaddrs;
 	while (walk_size < addrs_size) {
+		if (walk_size + sizeof(sa_family_t) > addrs_size) {
+			kfree(kaddrs);
+			return -EINVAL;
+		}
+
 		sa_addr = (struct sockaddr *)addr_buf;
 		af = sctp_get_af_specific(sa_addr->sa_family);
 
···
 	/* Walk through the addrs buffer and count the number of addresses. */
 	addr_buf = kaddrs;
 	while (walk_size < addrs_size) {
+		if (walk_size + sizeof(sa_family_t) > addrs_size) {
+			err = -EINVAL;
+			goto out_free;
+		}
+
 		sa_addr = (union sctp_addr *)addr_buf;
 		af = sctp_get_af_specific(sa_addr->sa.sa_family);
-		port = ntohs(sa_addr->v4.sin_port);
 
 		/* If the address family is not supported or if this address
 		 * causes the address buffer to overflow return EINVAL.
···
 			err = -EINVAL;
 			goto out_free;
 		}
+
+		port = ntohs(sa_addr->v4.sin_port);
 
 		/* Save current address so we can work with it */
 		memcpy(&to, sa_addr, af->sockaddr_len);