ARM: dts: stm32: Add DHCOR based DRC Compact board

Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.

Signed-off-by: Marek Vasut <[e-mail]>
Cc: Alexandre Torgue <[e-mail]>
Cc: [e-mail]
To: [e-mail]
Signed-off-by: Alexandre Torgue <[e-mail]>

arch/arm/boot/dts/Makefile

···
 	stm32mp151a-prtt1c.dtb \
 	stm32mp151a-prtt1s.dtb \
 	stm32mp153c-dhcom-drc02.dtb \
+	stm32mp153c-dhcor-drc-compact.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \
 	stm32mp157a-dk1.dtb \

arch/arm/boot/dts/stm32mp153c-dhcor-drc-compact.dts

···
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <[e-mail]>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * DRC Compact PCB number: 627-100 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOR DRC Compact";
+	compatible = "dh,stm32mp153c-dhcor-drc-compact",
+		     "dh,stm32mp153c-dhcor-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_c>;
+	pinctrl-1 = <&m_can1_sleep_pins_c>;
+	status = "okay";
+};

arch/arm/boot/dts/stm32mp15xx-dhcor-drc-compact.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <[e-mail]>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		mmc0 = &sdmmc1;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+		serial0 = &uart4;
+		serial1 = &uart8;
+		serial2 = &usart3;
+		serial3 = &uart5;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "yellow:user0";
+			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "red:user1";
+			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {	/* X11 ADC inputs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 6>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <0 1 2>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "DRCC-VAR2", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "DRCC-GPIO0", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "DRCC-GPIO5", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "DRCC-HW2",
+			  "DRCC-GPIO4", "", "", "",
+			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
+			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DRCC-GPIO2",
+			  "", "DRCC-GPIO1", "", "",
+			  "", "", "", "";
+};
+
+&i2c1 {	/* X11 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {	/* MicroSD */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc2 {	/* eMMC */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	bus-width = <4>;
+	mmc-ddr-3_3v;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi2 {	/* X11 SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	label = "UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_d>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart5 {	/* X11 UART */
+	label = "X11-UART5";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	label = "RS485-1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart3 {	/* RS485 or RS232 */
+	label = "RS485-2";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart3_pins_e>;
+	pinctrl-1 = <&usart3_sleep_pins_e>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};