Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:

at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency

integrator:
- fix an OF-related regression against 3.15

mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board

qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver

samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm

sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...

Documentation/devicetree/bindings/arm/armada-38x.txt

···
 
 Required root node property:
 
- - compatible: must contain either "marvell,armada380" or
-   "marvell,armada385" depending on the variant of the SoC being used.
+ - compatible: must contain "marvell,armada380"
+
+In addition, boards using the Marvell Armada 385 SoC shall have the
+following property before the previous one:
+
+Required root node property:
+
+compatible: must contain "marvell,armada385"
+
+Example:
+
+compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380";

arch/arm/boot/dts/Makefile

···
 	stih415-b2020.dtb \
 	stih416-b2000.dtb \
 	stih416-b2020.dtb \
-	stih416-b2020-revE.dtb
+	stih416-b2020e.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-cubieboard.dtb \

arch/arm/boot/dts/armada-380.dtsi

···
 
 / {
 	model = "Marvell Armada 380 family SoC";
-	compatible = "marvell,armada380", "marvell,armada38x";
+	compatible = "marvell,armada380";
 
 	cpus {
 		#address-cells = <1>;

arch/arm/boot/dts/armada-385-db.dts

···
 
 / {
 	model = "Marvell Armada 385 Development Board";
-	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada380";
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlyprintk";

arch/arm/boot/dts/armada-385-rd.dts

···
 
 / {
 	model = "Marvell Armada 385 Reference Design";
-	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380";
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlyprintk";

arch/arm/boot/dts/armada-385.dtsi

···
 
 / {
 	model = "Marvell Armada 385 family SoC";
-	compatible = "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,armada385", "marvell,armada380";
 
 	cpus {
 		#address-cells = <1>;

arch/arm/boot/dts/armada-38x.dtsi

···
 
 / {
 	model = "Marvell Armada 38x family SoC";
-	compatible = "marvell,armada38x";
+	compatible = "marvell,armada380";
 
 	aliases {
 		gpio0 = &gpio0;

arch/arm/boot/dts/at91sam9261.dtsi

···
 				#size-cells = <0>;
 				#interrupt-cells = <1>;
 
-				slow_rc_osc: slow_rc_osc {
-					compatible = "fixed-clock";
+				main_osc: main_osc {
+					compatible = "atmel,at91rm9200-clk-main-osc";
 					#clock-cells = <0>;
-					clock-frequency = <32768>;
-					clock-accuracy = <50000000>;
-				};
-
-				clk32k: slck {
-					compatible = "atmel,at91sam9260-clk-slow";
-					#clock-cells = <0>;
-					clocks = <&slow_rc_osc &slow_xtal>;
+					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+					clocks = <&main_xtal>;
 				};
 
 				main: mainck {
 					compatible = "atmel,at91rm9200-clk-main";
 					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&main_xtal>;
+					clocks = <&main_osc>;
 				};
 
 				plla: pllack {
···
 					compatible = "atmel,at91rm9200-clk-master";
 					#clock-cells = <0>;
 					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
-					clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
 					atmel,clk-output-range = <0 94000000>;
 					atmel,clk-divisors = <1 2 4 0>;
 				};
···
 					#address-cells = <1>;
 					#size-cells = <0>;
 					interrupt-parent = <&pmc>;
-					clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
 
 					prog0: prog0 {
 						#clock-cells = <0>;

arch/arm/boot/dts/at91sam9261ek.dts

···
 		reg = <0x20000000 0x4000000>;
 	};
 
+	slow_xtal {
+		clock-frequency = <32768>;
+	};
+
 	main_xtal {
 		clock-frequency = <18432000>;
 	};

arch/arm/boot/dts/at91sam9n12.dtsi

···
 								      <595000000 650000000 3 0>,
 								      <545000000 600000000 0 1>,
 								      <495000000 555000000 1 1>,
-								      <445000000 500000000 1 2>,
-								      <400000000 450000000 1 3>;
+								      <445000000 500000000 2 1>,
+								      <400000000 450000000 3 1>;
 				};
 
 				plladiv: plladivck {

arch/arm/boot/dts/at91sam9x5.dtsi

···
 								       595000000 650000000 3 0
 								       545000000 600000000 0 1
 								       495000000 555000000 1 1
-								       445000000 500000000 1 2
-								       400000000 450000000 1 3>;
+								       445000000 500000000 2 1
+								       400000000 450000000 3 1>;
 				};
 
 				plladiv: plladivck {

arch/arm/boot/dts/exynos4.dtsi

···
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
-		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
+		reg = <0x10490000 0x10000>, <0x10480000 0x10000>;
 	};
 
 	combiner: interrupt-controller@10440000 {

arch/arm/boot/dts/imx51-babbage.dts

···
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	fsl,cd-controller;
-	fsl,wp-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &esdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;
-	cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
···
 				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
 				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
 				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-				MX51_PAD_GPIO1_0__SD1_CD		0x20d5
-				MX51_PAD_GPIO1_1__SD1_WP		0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0		0x100
+				MX51_PAD_GPIO1_1__GPIO1_1		0x100
 			>;
 		};
 

arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts

···
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>;
-	fsl,cd-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
···
 
 		pinctrl_esdhc1_cd: esdhc1_cd {
 			fsl,pins = <
-				MX51_PAD_GPIO1_0__SD1_CD 0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0 0xd5
 			>;
 		};
 

arch/arm/boot/dts/imx53-m53evk.dts

···
 		      <0xb0000000 0x20000000>;
 	};
 
-	soc {
-		display1: display@di1 {
-			compatible = "fsl,imx-parallel-display";
-			interface-pix-fmt = "bgr666";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_ipu_disp1>;
+	display1: display@di1 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp1>;
 
-			display-timings {
-				800x480p60 {
-					native-mode;
-					clock-frequency = <31500000>;
-					hactive = <800>;
-					vactive = <480>;
-					hfront-porch = <40>;
-					hback-porch = <88>;
-					hsync-len = <128>;
-					vback-porch = <33>;
-					vfront-porch = <9>;
-					vsync-len = <3>;
-					vsync-active = <1>;
-				};
+		display-timings {
+			800x480p60 {
+				native-mode;
+				clock-frequency = <31500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <40>;
+				hback-porch = <88>;
+				hsync-len = <128>;
+				vback-porch = <33>;
+				vfront-porch = <9>;
+				vsync-len = <3>;
+				vsync-active = <1>;
 			};
 		};
 

arch/arm/boot/dts/imx6dl-hummingboard.dts

···
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
 		};
 
+		pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
+			/*
+			 * Similar to pinctrl_usbotg_2, but we want it
+			 * pulled down for a fixed host connection.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
 		};
···
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-gw51xx.dts

···
 
 /dts-v1/;
 #include "imx6q.dtsi"
-#include "imx6qdl-gw54xx.dtsi"
+#include "imx6qdl-gw51xx.dtsi"
 
 / {
 	model = "Gateworks Ventana i.MX6 Quad GW51XX";

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

···
 		pinctrl-0 = <&pinctrl_cubox_i_ir>;
 	};
 
+	pwmleds {
+		compatible = "pwm-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+		front {
+			active-low;
+			label = "imx6:red:front";
+			max-brightness = <248>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 
···
 			>;
 		};
 
+		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_spdif: cubox-i-spdif {
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
 
 		pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
+		};
+
+		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+			/*
+			 * The Cubox-i pulls this low, but as it's pointless
+			 * leaving it as a pull-up, even if it is just 10uA.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
 		};
 
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
···
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw51xx.dtsi

···
 	status = "okay";
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

···
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {
···
 	codec: sgtl5000@0a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
-		clocks = <&clks 169>;
+		clocks = <&clks 201>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

···
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-microsom.dtsi

···
 				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
 			>;
 		};
-
-		pinctrl_microsom_usbotg: microsom-usbotg {
-			/*
-			 * Similar to pinctrl_usbotg_2, but we want it
-			 * pulled down for a fixed host connection.
-			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
-		};
 	};
 };
 
···
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_uart1>;
 	status = "okay";
-};
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_microsom_usbotg>;
 };

arch/arm/boot/dts/imx6sl.dtsi

···
 				compatible = "fsl,imx6sl-fec", "fsl,imx25-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks IMX6SL_CLK_ENET_REF>,
+				clocks = <&clks IMX6SL_CLK_ENET>,
 					 <&clks IMX6SL_CLK_ENET_REF>;
 				clock-names = "ipg", "ahb";
 				status = "disabled";

arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts

···
 		compatible = "ethernet-phy-id0141.0cb0",
 		             "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
-		phy-connection-type = "rgmii-id";
 	};
 
 	ethphy1: ethernet-phy@1 {
···
 		compatible = "ethernet-phy-id0141.0cb0",
 		             "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
-		phy-connection-type = "rgmii-id";
 	};
 };
 
···
 	status = "okay";
 	ethernet0-port@0 {
 		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
 	};
 };
 
···
 	status = "okay";
 	ethernet1-port@0 {
 		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
 	};
 };

arch/arm/boot/dts/stih415.dtsi

···
 
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii0>;
-			clock-names	= "stmmaceth";
-			clocks		= <&clk_s_a1_ls CLK_GMAC0_PHY>;
+			clock-names	= "stmmaceth", "sti-ethclk";
+			clocks		= <&clk_s_a1_ls CLK_ICN_IF_2>, <&clk_s_a1_ls CLK_GMAC0_PHY>;
 		};
 
 		ethernet1: dwmac@fef08000 {
···
 			reset-names		= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii1>;
-			clock-names	= "stmmaceth";
-			clocks		= <&clk_s_a0_ls CLK_ETH1_PHY>;
+			clock-names	= "stmmaceth", "sti-ethclk";
+			clocks		= <&clk_s_a0_ls CLK_ICN_REG>, <&clk_s_a0_ls CLK_ETH1_PHY>;
 		};
 
 		rc: rc@fe518000 {

arch/arm/boot/dts/stih416.dtsi

···
 			reset-names		= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii0>;
-			clock-names	= "stmmaceth";
-			clocks		= <&clk_s_a1_ls CLK_GMAC0_PHY>;
+			clock-names	= "stmmaceth", "sti-ethclk";
+			clocks		= <&clk_s_a1_ls CLK_ICN_IF_2>, <&clk_s_a1_ls CLK_GMAC0_PHY>;
 		};
 
 		ethernet1: dwmac@fef08000 {
···
 			reset-names	= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii1>;
-			clock-names	= "stmmaceth";
-			clocks		= <&clk_s_a0_ls CLK_ETH1_PHY>;
+			clock-names	= "stmmaceth", "sti-ethclk";
+			clocks		= <&clk_s_a0_ls CLK_ICN_REG>, <&clk_s_a0_ls CLK_ETH1_PHY>;
 		};
 
 		rc: rc@fe518000 {

arch/arm/configs/imx_v6_v7_defconfig

···
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_CODA=y
 CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y

arch/arm/configs/multi_v7_defconfig

···
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
+CONFIG_QCOM_GSBI=y
 CONFIG_COMMON_CLK_QCOM=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_MMCC_8960=y

arch/arm/configs/mvebu_v7_defconfig

···
 CONFIG_MACH_ARMADA_375=y
 CONFIG_MACH_ARMADA_38X=y
 CONFIG_MACH_ARMADA_XP=y
+CONFIG_MACH_DOVE=y
 CONFIG_NEON=y
 # CONFIG_CACHE_L2X0 is not set
 # CONFIG_SWP_EMULATE is not set
···
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_I2C=y
 CONFIG_SPI=y
 CONFIG_SPI_ORION=y

arch/arm/mach-exynos/hotplug.c

···
 		if (cpu == 1)
 			exynos_cpu_power_down(cpu);
 
-		/*
-		 * here's the WFI
-		 */
-		asm(".word	0xe320f003\n"
-		    :
-		    :
-		    : "memory", "cc");
+		wfi();
 
 		if (pen_release == cpu_logical_map(cpu)) {
 			/*

arch/arm/mach-exynos/mcpm-exynos.c

···
 
 #define EXYNOS5420_CPUS_PER_CLUSTER	4
 #define EXYNOS5420_NR_CLUSTERS		2
-#define MCPM_BOOT_ADDR_OFFSET		0x1c
 
 /*
  * The common v7_exit_coherency_flush API could not be used because of the
···
 	pr_info("Exynos MCPM support installed\n");
 
 	/*
-	 * Future entries into the kernel can now go
-	 * through the cluster entry vectors.
+	 * U-Boot SPL is hardcoded to jump to the start of ns_sram_base_addr
+	 * as part of secondary_cpu_start().  Let's redirect it to the
+	 * mcpm_entry_point().
 	 */
-	__raw_writel(virt_to_phys(mcpm_entry_point),
-			ns_sram_base_addr + MCPM_BOOT_ADDR_OFFSET);
+	__raw_writel(0xe59f0000, ns_sram_base_addr);     /* ldr r0, [pc, #0] */
+	__raw_writel(0xe12fff10, ns_sram_base_addr + 4); /* bx  r0 */
+	__raw_writel(virt_to_phys(mcpm_entry_point), ns_sram_base_addr + 8);
 
 	iounmap(ns_sram_base_addr);
 

arch/arm/mach-exynos/pm.c

···
 	tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0);
 	__raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION);
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		exynos_cpu_save_register();
 
 	return 0;
···
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		exynos_cpu_restore_register();
 
 	/* For release retention */
···
 
 	s3c_pm_do_restore_core(exynos_core_save, ARRAY_SIZE(exynos_core_save));
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(S5P_VA_SCU);
 
 early_wakeup:
···
 	case CPU_PM_ENTER:
 		if (cpu == 0) {
 			exynos_pm_central_suspend();
-			exynos_cpu_save_register();
+			if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
+				exynos_cpu_save_register();
 		}
 		break;
 
 	case CPU_PM_EXIT:
 		if (cpu == 0) {
-			if (!soc_is_exynos5250())
+			if (read_cpuid_part_number() ==
+					ARM_CPU_PART_CORTEX_A9) {
 				scu_enable(S5P_VA_SCU);
-			exynos_cpu_restore_register();
+				exynos_cpu_restore_register();
+			}
 			exynos_pm_central_resume();
 		}
 		break;

arch/arm/mach-imx/clk-imx6sl.c

···
 	clks[IMX6SL_CLK_ECSPI2]       = imx_clk_gate2("ecspi2",       "ecspi_root",        base + 0x6c, 2);
 	clks[IMX6SL_CLK_ECSPI3]       = imx_clk_gate2("ecspi3",       "ecspi_root",        base + 0x6c, 4);
 	clks[IMX6SL_CLK_ECSPI4]       = imx_clk_gate2("ecspi4",       "ecspi_root",        base + 0x6c, 6);
+	clks[IMX6SL_CLK_ENET]         = imx_clk_gate2("enet",         "ipg",               base + 0x6c, 10);
 	clks[IMX6SL_CLK_EPIT1]        = imx_clk_gate2("epit1",        "perclk",            base + 0x6c, 12);
 	clks[IMX6SL_CLK_EPIT2]        = imx_clk_gate2("epit2",        "perclk",            base + 0x6c, 14);
 	clks[IMX6SL_CLK_EXTERN_AUDIO] = imx_clk_gate2("extern_audio", "extern_audio_podf", base + 0x6c, 16);

arch/arm/mach-integrator/integrator_ap.c

···
 static void __init ap_init_of(void)
 {
 	unsigned long sc_dec;
-	struct device_node *root;
 	struct device_node *syscon;
 	struct device_node *ebi;
 	struct device *parent;
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 	u32 ap_sc_id;
-	int err;
 	int i;
 
-	/* Here we create an SoC device for the root node */
-	root = of_find_node_by_path("/");
-	if (!root)
-		return;
-
-	syscon = of_find_matching_node(root, ap_syscon_match);
+	syscon = of_find_matching_node(NULL, ap_syscon_match);
 	if (!syscon)
 		return;
-	ebi = of_find_matching_node(root, ebi_match);
+	ebi = of_find_matching_node(NULL, ebi_match);
 	if (!ebi)
 		return;
 
···
 	if (!ebi_base)
 		return;
 
+	of_platform_populate(NULL, of_default_bus_match_table,
+			ap_auxdata_lookup, NULL);
+
 	ap_sc_id = readl(ap_syscon_base);
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
 		return;
 
-	err = of_property_read_string(root, "compatible",
-				      &soc_dev_attr->soc_id);
-	if (err)
-		return;
-	err = of_property_read_string(root, "model", &soc_dev_attr->machine);
-	if (err)
-		return;
+	soc_dev_attr->soc_id = "XVC";
+	soc_dev_attr->machine = "Integrator/AP";
 	soc_dev_attr->family = "Integrator";
 	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%c",
 					   'A' + (ap_sc_id & 0x0f));
···
 
 	parent = soc_device_to_device(soc_dev);
 	integrator_init_sysfs(parent, ap_sc_id);
-
-	of_platform_populate(root, of_default_bus_match_table,
-			ap_auxdata_lookup, parent);
 
 	sc_dec = readl(ap_syscon_base + INTEGRATOR_SC_DEC_OFFSET);
 	for (i = 0; i < 4; i++) {

arch/arm/mach-integrator/integrator_cp.c

···
 
 static void __init intcp_init_of(void)
 {
-	struct device_node *root;
 	struct device_node *cpcon;
 	struct device *parent;
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 	u32 intcp_sc_id;
-	int err;
 
-	/* Here we create an SoC device for the root node */
-	root = of_find_node_by_path("/");
-	if (!root)
-		return;
-
-	cpcon = of_find_matching_node(root, intcp_syscon_match);
+	cpcon = of_find_matching_node(NULL, intcp_syscon_match);
 	if (!cpcon)
 		return;
 
···
 	if (!intcp_con_base)
 		return;
 
+	of_platform_populate(NULL, of_default_bus_match_table,
+			     intcp_auxdata_lookup, NULL);
+
 	intcp_sc_id = readl(intcp_con_base);
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
 		return;
 
-	err = of_property_read_string(root, "compatible",
-				      &soc_dev_attr->soc_id);
-	if (err)
-		return;
-	err = of_property_read_string(root, "model", &soc_dev_attr->machine);
-	if (err)
-		return;
+	soc_dev_attr->soc_id = "XCV";
+	soc_dev_attr->machine = "Integrator/CP";
 	soc_dev_attr->family = "Integrator";
 	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%c",
 					   'A' + (intcp_sc_id & 0x0f));
···
 
 	parent = soc_device_to_device(soc_dev);
 	integrator_init_sysfs(parent, intcp_sc_id);
-	of_platform_populate(root, of_default_bus_match_table,
-			intcp_auxdata_lookup, parent);
 }
 
 static const char * intcp_dt_board_compat[] = {

arch/arm/mach-mvebu/Kconfig

···
 	select ZONE_DMA if ARM_LPAE
 	select ARCH_REQUIRE_GPIOLIB
 	select PCI_QUIRKS if PCI
+	select OF_ADDRESS_PCI
 
 if ARCH_MVEBU
 
···
 	bool
 	select ARMADA_370_XP_TIMER
 	select CACHE_L2X0
+	select ARM_CPU_SUSPEND
 
 config MACH_ARMADA_370
 	bool "Marvell Armada 370 boards" if ARCH_MULTI_V7

drivers/clocksource/exynos_mct.c

···
 }
 
 /* Clocksource handling */
-static void exynos4_mct_frc_start(u32 hi, u32 lo)
+static void exynos4_mct_frc_start(void)
 {
 	u32 reg;
-
-	exynos4_mct_write(lo, EXYNOS4_MCT_G_CNT_L);
-	exynos4_mct_write(hi, EXYNOS4_MCT_G_CNT_U);
 
 	reg = __raw_readl(reg_base + EXYNOS4_MCT_G_TCON);
 	reg |= MCT_G_TCON_START;
···
 
 static void exynos4_frc_resume(struct clocksource *cs)
 {
-	exynos4_mct_frc_start(0, 0);
+	exynos4_mct_frc_start();
 }
 
 struct clocksource mct_frc = {
···
 
 static void __init exynos4_clocksource_init(void)
 {
-	exynos4_mct_frc_start(0, 0);
+	exynos4_mct_frc_start();
 
 	if (clocksource_register_hz(&mct_frc, clk_rate))
 		panic("%s: can't register clocksource\n", mct_frc.name);

drivers/misc/Kconfig

···
 config ATMEL_PWM
 	tristate "Atmel AT32/AT91 PWM support"
 	depends on HAVE_CLK
-	depends on AVR32 || AT91SAM9263 || AT91SAM9RL || AT91SAM9G45
+	depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
 	help
 	  This option enables device driver support for the PWM channels
 	  on certain Atmel processors.  Pulse Width Modulation is used for

drivers/tty/serial/msm_serial.c

···
 	{ }
 };
 
-static int __init msm_serial_probe(struct platform_device *pdev)
+static int msm_serial_probe(struct platform_device *pdev)
 {
 	struct msm_port *msm_port;
 	struct resource *resource;

include/dt-bindings/clock/imx6sl-clock.h

···
 #define IMX6SL_CLK_USDHC4		132
 #define IMX6SL_CLK_PLL4_AUDIO_DIV	133
 #define IMX6SL_CLK_SPBA			134
-#define IMX6SL_CLK_END			135
+#define IMX6SL_CLK_ENET			135
+#define IMX6SL_CLK_END			136
 
 #endif /* __DT_BINDINGS_CLOCK_IMX6SL_H */

include/dt-bindings/clock/stih415-clks.h

···
 #define CLK_ETH1_PHY		4
 
 /* CLOCKGEN A1 */
+#define CLK_ICN_IF_2		0
 #define CLK_GMAC0_PHY		3
 
 #endif

include/dt-bindings/clock/stih416-clks.h

···
 #define CLK_ETH1_PHY		4
 
 /* CLOCKGEN A1 */
+#define CLK_ICN_IF_2		0
 #define CLK_GMAC0_PHY		3
 
 #endif