Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.

The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."

* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...

Documentation/devicetree/bindings/arm/omap/l3-noc.txt

···
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+- reg:	Contains L3 register address range for each noc domain.
 - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain.
 
 Examples:

Documentation/devicetree/bindings/arm/omap/timer.txt

···
 OMAP Timer bindings
 
 Required properties:
-- compatible:		Must be "ti,omap2-timer" for OMAP2+ controllers.
+- compatible:		Should be set to one of the below. Please note that
+			OMAP44xx devices have timer instances that are 100%
+			register compatible with OMAP3xxx devices as well as
+			newer timers that are not 100% register compatible.
+			So for OMAP44xx devices timer instances may use
+			different compatible strings.
+
+			ti,omap2420-timer (applicable to OMAP24xx devices)
+			ti,omap3430-timer (applicable to OMAP3xxx/44xx devices)
+			ti,omap4430-timer (applicable to OMAP44xx devices)
+			ti,omap5430-timer (applicable to OMAP543x devices)
+			ti,am335x-timer	(applicable to AM335x devices)
+			ti,am335x-timer-1ms (applicable to AM335x devices)
+
 - reg:			Contains timer register address range (base address and
 			length).
 - interrupts: 		Contains the interrupt information for the timer. The
···
 Example:
 
 timer12: timer@48304000 {
-	compatible = "ti,omap2-timer";
+	compatible = "ti,omap3430-timer";
 	reg = <0x48304000 0x400>;
 	interrupts = <95>;
 	ti,hwmods = "timer12"

Documentation/devicetree/bindings/arm/samsung/sysreg.txt

···
+SAMSUNG S5P/Exynos SoC series System Registers (SYSREG)
+
+Properties:
+ - name : should be 'sysreg';
+ - compatible : should contain "samsung,<chip name>-sysreg", "syscon";
+   For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon";
+ - reg : offset and length of the register set.

Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt

···
 Required properties:
 - compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
 - reg : Should contain registers location and length
+- interrupts : Should contain the interrupt numbers of DMA channels.
+  If a channel is empty/reserved, 0 should be filled in place.
+- #dma-cells : Must be <1>.  The number cell specifies the channel ID.
+- dma-channels : Number of channels supported by the DMA controller
+
+Optional properties:
+- interrupt-names : Name of DMA channel interrupts
 
 Supported chips:
 imx23, imx28.
 
 Examples:
-dma-apbh@80004000 {
+
+dma_apbh: dma-apbh@80004000 {
 	compatible = "fsl,imx28-dma-apbh";
-	reg = <0x80004000 2000>;
+	reg = <0x80004000 0x2000>;
+	interrupts = <82 83 84 85
+		      88 88 88 88
+		      88 88 88 88
+		      87 86 0 0>;
+	interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
+			  "gpmi0", "gmpi1", "gpmi2", "gmpi3",
+			  "gpmi4", "gmpi5", "gpmi6", "gmpi7",
+			  "hsadc", "lcdif", "empty", "empty";
+	#dma-cells = <1>;
+	dma-channels = <16>;
 };
 
-dma-apbx@80024000 {
+dma_apbx: dma-apbx@80024000 {
 	compatible = "fsl,imx28-dma-apbx";
-	reg = <0x80024000 2000>;
+	reg = <0x80024000 0x2000>;
+	interrupts = <78 79 66 0
+		      80 81 68 69
+		      70 71 72 73
+		      74 75 76 77>;
+	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+			  "saif0", "saif1", "i2c0", "i2c1",
+			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
+			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+	#dma-cells = <1>;
+	dma-channels = <16>;
+};
+
+DMA clients connected to the MXS DMA controller must use the format
+described in the dma.txt file.
+
+Examples:
+
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112>;
+	dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+	dma-names = "rx", "tx";
 };

Documentation/devicetree/bindings/fb/mxsfb.txt

···
   imx23 and imx28.
 - reg: Address and length of the register set for lcdif
 - interrupts: Should contain lcdif interrupts
+- display : phandle to display node (see below for details)
 
-Optional properties:
-- panel-enable-gpios : Should specify the gpio for panel enable
+* display node
+
+Required properties:
+- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
+- bus-width : number of data lines.  Could be <8>, <16>, <18> or <24>.
+
+Required sub-node:
+- display-timings : Refer to binding doc display-timing.txt for details.
 
 Examples:
 
···
 	compatible = "fsl,imx28-lcdif";
 	reg = <0x80030000 2000>;
 	interrupts = <38 86>;
-	panel-enable-gpios = <&gpio3 30 0>;
+
+	display: display {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <164>;
+				hback-porch = <89>;
+				hsync-len = <10>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
 };

Documentation/devicetree/bindings/gpio/gpio-omap.txt

···
   - "ti,omap2-gpio" for OMAP2 controllers
   - "ti,omap3-gpio" for OMAP3 controllers
   - "ti,omap4-gpio" for OMAP4 controllers
+- gpio-controller : Marks the device node as a GPIO controller.
 - #gpio-cells : Should be two.
   - first cell is the pin number
   - second cell is used to specify optional parameters (unused)
-- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller.
 - #interrupt-cells : Should be 2.
-- interrupt-controller: Mark the device node as an interrupt controller
   The first cell is the GPIO number.
   The second cell is used to specify flags:
     bits[3:0] trigger type and level flags:
···
 gpio4: gpio4 {
     compatible = "ti,omap4-gpio";
     ti,hwmods = "gpio4";
-    #gpio-cells = <2>;
     gpio-controller;
-    #interrupt-cells = <2>;
+    #gpio-cells = <2>;
     interrupt-controller;
+    #interrupt-cells = <2>;
 };

Documentation/devicetree/bindings/gpu/samsung-g2d.txt

···
+* Samsung 2D Graphics Accelerator
+
+Required properties:
+  - compatible : value should be one among the following:
+	(a) "samsung,s5pv210-g2d" for G2D IP present in S5PV210 & Exynos4210 SoC
+	(b) "samsung,exynos4212-g2d" for G2D IP present in Exynos4x12 SoCs
+	(c) "samsung,exynos5250-g2d" for G2D IP present in Exynos5250 SoC
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : G2D interrupt number to the CPU.
+
+Example:
+	g2d@12800000 {
+		compatible = "samsung,s5pv210-g2d";
+		reg = <0x12800000 0x1000>;
+		interrupts = <0 89 0>;
+		status = "disabled";
+	};

Documentation/devicetree/bindings/i2c/i2c-mxs.txt

···
 Required properties:
 - compatible: Should be "fsl,<chip>-i2c"
 - reg: Should contain registers location and length
-- interrupts: Should contain ERROR and DMA interrupts
+- interrupts: Should contain ERROR interrupt number
 - clock-frequency: Desired I2C bus clock frequency in Hz.
                    Only 100000Hz and 400000Hz modes are supported.
-- fsl,i2c-dma-channel: APBX DMA channel for the I2C
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and I2C DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Examples:
 
···
 	#size-cells = <0>;
 	compatible = "fsl,imx28-i2c";
 	reg = <0x80058000 2000>;
-	interrupts = <111 68>;
+	interrupts = <111>;
 	clock-frequency = <100000>;
-	fsl,i2c-dma-channel = <6>;
+	dmas = <&dma_apbx 6>;
+	dma-names = "rx-tx";
 };

Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt

···
+NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
+
+Required properties:
+- compatible : should be:
+	"nvidia,tegra114-i2c"
+	"nvidia,tegra30-i2c"
+	"nvidia,tegra20-i2c"
+	"nvidia,tegra20-i2c-dvc"
+  Details of compatible are as follows:
+  nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
+	controller. This only support master mode of I2C communication. Register
+	interface/offset and interrupts handling are different than generic I2C
+	controller. Driver of DVC I2C controller is only compatible with
+	"nvidia,tegra20-i2c-dvc".
+  nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
+	master and slave mode of I2C communication. The i2c-tegra driver only
+	support master mode of I2C communication. Driver of I2C controller is
+	only compatible with "nvidia,tegra20-i2c".
+  nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
+	very much similar to Tegra20 I2C controller with additional feature:
+	Continue Transfer Support. This feature helps to implement M_NO_START
+	as per I2C core API transfer flags. Driver of I2C controller is
+	compatible with "nvidia,tegra30-i2c" to enable the continue transfer
+	support. This is also compatible with "nvidia,tegra20-i2c" without
+	continue transfer support.
+  nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
+	very much similar to Tegra30 I2C controller with some hardware
+	modification:
+	 - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
+	   fast-clk. Tegra114 has only one clock source called as div-clk and
+	   hence clock mechanism is changed in I2C controller.
+	 - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
+	   default and there is no way to disable it. Tegra114 has this
+	   interrupt disable by default and SW need to enable explicitly.
+	Due to above changes, Tegra114 I2C driver makes incompatible with
+	previous hardware driver. Hence, tegra114 I2C controller is compatible
+	with "nvidia,tegra114-i2c".
+- reg: Should contain I2C controller registers physical address and length.
+- interrupts: Should contain I2C controller interrupts.
+- address-cells: Address cells for I2C device address.
+- size-cells: Size of the I2C device address.
+- clocks: Clock ID as per
+		Documentation/devicetree/bindings/clock/tegra<chip-id>.txt
+	for I2C controller.
+- clock-names: Name of the clock:
+	Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk".
+	Tegra114 I2C controller: "div-clk".
+
+Example:
+
+	i2c@7000c000 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 12>, <&tegra_car 124>;
+		clock-names = "div-clk", "fast-clk";
+		status = "disabled";
+	};

Documentation/devicetree/bindings/mmc/mxs-mmc.txt

···
 Required properties:
 - compatible: Should be "fsl,<chip>-mmc".  The supported chips include
   imx23 and imx28.
-- interrupts: Should contain ERROR and DMA interrupts
-- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Examples:
 
 ssp0: ssp@80010000 {
 	compatible = "fsl,imx28-mmc";
 	reg = <0x80010000 2000>;
-	interrupts = <96 82>;
-	fsl,ssp-dma-channel = <0>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
 	bus-width = <8>;
 };

Documentation/devicetree/bindings/mtd/gpmi-nand.txt

···
   - compatible : should be "fsl,<chip>-gpmi-nand"
   - reg : should contain registers location and length for gpmi and bch.
   - reg-names: Should contain the reg names "gpmi-nand" and "bch"
-  - interrupts : The first is the DMA interrupt number for GPMI.
-                 The second is the BCH interrupt number.
-  - interrupt-names : The interrupt names "gpmi-dma", "bch";
-  - fsl,gpmi-dma-channel : Should contain the dma channel it uses.
+  - interrupts : BCH interrupt number.
+  - interrupt-names : Should be "bch".
+  - dmas: DMA specifier, consisting of a phandle to DMA controller node
+    and GPMI DMA channel ID.
+    Refer to dma.txt and fsl-mxs-dma.txt for details.
+  - dma-names: Must be "rx-tx".
 
 Optional properties:
   - nand-on-flash-bbt: boolean to enable on flash bbt option if not
···
 	#size-cells = <1>;
 	reg = <0x8000c000 2000>, <0x8000a000 2000>;
 	reg-names = "gpmi-nand", "bch";
-	interrupts = <88>, <41>;
-	interrupt-names = "gpmi-dma", "bch";
-	fsl,gpmi-dma-channel = <4>;
+	interrupts = <41>;
+	interrupt-names = "bch";
+	dmas = <&dma_apbh 4>;
+	dma-names = "rx-tx";
 
 	partition@0 {
 	...

Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt

···
     0: Disable the internal pull-up
     1: Enable the internal pull-up
 
+Note that when enabling the pull-up, the internal pad keeper gets disabled.
+Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
+will only disable the internal pad keeper.
+
 Examples:
 
 pinctrl@80018000 {

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt

···
 
 Required properties:
 - compatible : "nvidia,tegra-audio-alc5632"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
···
 
 	nvidia,i2s-controller = <&tegra_i2s1>;
 	nvidia,audio-codec = <&alc5632>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt

···
 
 Required properties:
 - compatible : "nvidia,tegra-audio-trimslice"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
 - nvidia,audio-codec : The phandle of the WM8903 audio codec
 
···
 	compatible = "nvidia,tegra-audio-trimslice";
 	nvidia,i2s-controller = <&tegra_i2s1>;
 	nvidia,audio-codec = <&codec>;
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt

···
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm8753"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
···
 
 	nvidia,i2s-controller = <&i2s1>;
 	nvidia,audio-codec = <&wm8753>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
 

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt

···
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm8903"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
···
 	nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
 	nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
 	nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
 

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt

···
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm9712"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
···
 		"Mic", "MIC1";
 
 	nvidia,ac97-controller = <&ac97>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };

Documentation/devicetree/bindings/spi/mxs-spi.txt

···
 Required properties:
 - compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28"
 - reg: Offset and length of the register set for the device
-- interrupts: Should contain SSP interrupts (error irq first, dma irq second)
-- fsl,ssp-dma-channel: APBX DMA channel for the SSP
+- interrupts: Should contain SSP ERROR interrupt
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Optional properties:
 - clock-frequency : Input clock frequency to the SPI block in Hz.
···
 	#size-cells = <0>;
 	compatible = "fsl,imx28-spi";
 	reg = <0x80010000 0x2000>;
-	interrupts = <96 82>;
-	fsl,ssp-dma-channel = <0>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
 };

Documentation/devicetree/bindings/spi/spi-davinci.txt

···
+Davinci SPI controller device bindings
+
+Required properties:
+- #address-cells: number of cells required to define a chip select
+	address on the SPI bus. Should be set to 1.
+- #size-cells: should be zero.
+- compatible:
+	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
+	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+- reg: Offset and length of SPI controller register space
+- num-cs: Number of chip selects
+- ti,davinci-spi-intr-line: interrupt line used to connect the SPI
+	IP to the interrupt controller within the SoC. Possible values
+	are 0 and 1. Manual says one of the two possible interrupt
+	lines can be tied to the interrupt controller. Set this
+	based on a specifc SoC configuration.
+- interrupts: interrupt number mapped to CPU.
+- clocks: spi clk phandle
+
+Example of a NOR flash slave device (n25q032) connected to DaVinci
+SPI controller device over the SPI bus.
+
+spi0:spi@20BF0000 {
+	#address-cells			= <1>;
+	#size-cells			= <0>;
+	compatible			= "ti,dm6446-spi";
+	reg				= <0x20BF0000 0x1000>;
+	num-cs				= <4>;
+	ti,davinci-spi-intr-line	= <0>;
+	interrupts			= <338>;
+	clocks				= <&clkspi>;
+
+	flash: n25q032@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "test";
+			reg = <0x80000 0x380000>;
+		};
+	};
+};

Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt

···
   imx23 and imx28.
 - reg : Address and length of the register set for the device
 - interrupts : Should contain the auart interrupt numbers
-
-Optional properties:
-- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other
-		is for TX. If you add this property, it also means that you
-		will enable the DMA support for the auart.
-		Note: due to the hardware bug in imx23(see errata : 2836),
-		only the imx28 can enable the DMA support for the auart.
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and AUART DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: "rx" for RX channel, "tx" for TX channel.
 
 Example:
 auart0: serial@8006a000 {
 	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 	reg = <0x8006a000 0x2000>;
-	interrupts = <112 70 71>;
-	fsl,auart-dma-channel = <8 9>;
+	interrupts = <112>;
+	dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+	dma-names = "rx", "tx";
 };
 
 Note: Each auart port should have an alias correctly numbered in "aliases"

Documentation/devicetree/bindings/usb/exynos-usb.txt

···
  - reg: physical base address of the controller and length of memory mapped
    region.
  - interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
 
 Optional properties:
  - samsung,vbus-gpio:  if present, specifies the GPIO that
···
 		reg = <0x12110000 0x100>;
 		interrupts = <0 71 0>;
 		samsung,vbus-gpio = <&gpx2 6 1 3 3>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};
 
 OHCI
···
  - reg: physical base address of the controller and length of memory mapped
    region.
  - interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
 
 Example:
 	usb@12120000 {
 		compatible = "samsung,exynos4210-ohci";
 		reg = <0x12120000 0x100>;
 		interrupts = <0 71 0>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};

Documentation/devicetree/bindings/usb/omap-usb.txt

···
    represents PERIPHERAL.
  - power : Should be "50". This signifies the controller can supply upto
    100mA when operating in host mode.
+ - usb-phy : the phandle for the PHY device
 
 Optional properties:
  - ctrl-module : phandle of the control module this glue uses to write to

Documentation/devicetree/bindings/video/samsung-fimd.txt

···
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+		"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+		"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+		"samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */
+		"samsung,s5pc100-fimd"; /* for S5PC100 SoC  */
+		"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+		"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+		"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupt-parent: should be the phandle of the fimd controller's
+		parent interrupt controller.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+		 format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+	"lcd_sys", in the same order as they were listed in the interrupts
+        property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+         clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+               property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- samsung,power-domain: a phandle to FIMD power domain node.
+
+Example:
+
+SoC specific DT entry:
+
+	fimd@11c00000 {
+		compatible = "samsung,exynos4210-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x11c00000 0x20000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <11 0>, <11 1>, <11 2>;
+		clocks = <&clock 140>, <&clock 283>;
+		clock-names = "sclk_fimd", "fimd";
+		samsung,power-domain = <&pd_lcd0>;
+		status = "disabled";
+	};
+
+Board specific DT entry:
+
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};

arch/arm/boot/dts/Makefile

···
 	exynos4412-smdk4412.dtb \
 	exynos4412-origen.dtb \
 	exynos5250-arndale.dtb \
+	exynos5440-sd5v1.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
 	exynos5440-ssdk5440.dtb
···
 	imx28-tx28.dtb
 dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb
 dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
+	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
 	omap3-tobi.dtb \
+	omap3-igep0020.dtb \
+	omap3-igep0030.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \

arch/arm/boot/dts/am335x-bone.dts

···
 			status = "okay";
 		};
 
-		i2c1: i2c@44e0b000 {
+		i2c0: i2c@44e0b000 {
 			status = "okay";
 			clock-frequency = <400000>;
 
···
 
 		led@2 {
 			label = "beaglebone:green:heartbeat";
-			gpios = <&gpio2 21 0>;
+			gpios = <&gpio1 21 0>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
 
 		led@3 {
 			label = "beaglebone:green:mmc0";
-			gpios = <&gpio2 22 0>;
+			gpios = <&gpio1 22 0>;
 			linux,default-trigger = "mmc0";
 			default-state = "off";
 		};
 
 		led@4 {
 			label = "beaglebone:green:usr2";
-			gpios = <&gpio2 23 0>;
+			gpios = <&gpio1 23 0>;
 			default-state = "off";
 		};
 
 		led@5 {
 			label = "beaglebone:green:usr3";
-			gpios = <&gpio2 24 0>;
+			gpios = <&gpio1 24 0>;
 			default-state = "off";
 		};
 	};

arch/arm/boot/dts/am335x-evm.dts

···
 			status = "okay";
 		};
 
-		i2c1: i2c@44e0b000 {
+		i2c0: i2c@44e0b000 {
 			status = "okay";
 			clock-frequency = <400000>;
 
···
 			};
 		};
 
-		i2c2: i2c@4802a000 {
+		i2c1: i2c@4802a000 {
 			status = "okay";
 			clock-frequency = <100000>;
 
···
 		debounce-delay-ms = <5>;
 		col-scan-delay-us = <2>;
 
-		row-gpios = <&gpio2 25 0	/* Bank1, pin25 */
-			     &gpio2 26 0	/* Bank1, pin26 */
-			     &gpio2 27 0>;	/* Bank1, pin27 */
+		row-gpios = <&gpio1 25 0	/* Bank1, pin25 */
+			     &gpio1 26 0	/* Bank1, pin26 */
+			     &gpio1 27 0>;	/* Bank1, pin27 */
 
-		col-gpios = <&gpio2 21 0	/* Bank1, pin21 */
-			     &gpio2 22 0>;	/* Bank1, pin22 */
+		col-gpios = <&gpio1 21 0	/* Bank1, pin21 */
+			     &gpio1 22 0>;	/* Bank1, pin22 */
 
 		linux,keymap = <0x0000008b	/* MENU */
 				0x0100009e	/* BACK */
···
 		switch@9 {
 			label = "volume-up";
 			linux,code = <115>;
-			gpios = <&gpio1 2 1>;
+			gpios = <&gpio0 2 1>;
 			gpio-key,wakeup;
 		};
 
 		switch@10 {
 			label = "volume-down";
 			linux,code = <114>;
-			gpios = <&gpio1 3 1>;
+			gpios = <&gpio0 3 1>;
 			gpio-key,wakeup;
 		};
 	};

arch/arm/boot/dts/am335x-evmsk.dts

···
 			status = "okay";
 		};
 
-		i2c1: i2c@44e0b000 {
+		i2c0: i2c@44e0b000 {
 			status = "okay";
 			clock-frequency = <400000>;
 
···
 
 		led@1 {
 			label = "evmsk:green:usr0";
-			gpios = <&gpio2 4 0>;
+			gpios = <&gpio1 4 0>;
 			default-state = "off";
 		};
 
 		led@2 {
 			label = "evmsk:green:usr1";
-			gpios = <&gpio2 5 0>;
+			gpios = <&gpio1 5 0>;
 			default-state = "off";
 		};
 
 		led@3 {
 			label = "evmsk:green:mmc0";
-			gpios = <&gpio2 6 0>;
+			gpios = <&gpio1 6 0>;
 			linux,default-trigger = "mmc0";
 			default-state = "off";
 		};
 
 		led@4 {
 			label = "evmsk:green:heartbeat";
-			gpios = <&gpio2 7 0>;
+			gpios = <&gpio1 7 0>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
···
 		switch@1 {
 			label = "button0";
 			linux,code = <0x100>;
-			gpios = <&gpio3 3 0>;
+			gpios = <&gpio2 3 0>;
 		};
 
 		switch@2 {
 			label = "button1";
 			linux,code = <0x101>;
-			gpios = <&gpio3 2 0>;
+			gpios = <&gpio2 2 0>;
 		};
 
 		switch@3 {
 			label = "button2";
 			linux,code = <0x102>;
-			gpios = <&gpio1 30 0>;
+			gpios = <&gpio0 30 0>;
 			gpio-key,wakeup;
 		};
 
 		switch@4 {
 			label = "button3";
 			linux,code = <0x103>;
-			gpios = <&gpio3 5 0>;
+			gpios = <&gpio2 5 0>;
 		};
 	};
 };

arch/arm/boot/dts/am33xx.dtsi

···
 		serial3 = &uart4;
 		serial4 = &uart5;
 		serial5 = &uart6;
+		d_can0 = &dcan0;
+		d_can1 = &dcan1;
 	};
 
 	cpus {
···
 			reg = <0x48200000 0x1000>;
 		};
 
-		gpio1: gpio@44e07000 {
+		gpio0: gpio@44e07000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
 			gpio-controller;
···
 			interrupts = <96>;
 		};
 
-		gpio2: gpio@4804c000 {
+		gpio1: gpio@4804c000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio2";
 			gpio-controller;
···
 			interrupts = <98>;
 		};
 
-		gpio3: gpio@481ac000 {
+		gpio2: gpio@481ac000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio3";
 			gpio-controller;
···
 			interrupts = <32>;
 		};
 
-		gpio4: gpio@481ae000 {
+		gpio3: gpio@481ae000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio4";
 			gpio-controller;
···
 			status = "disabled";
 		};
 
-		i2c1: i2c@44e0b000 {
+		i2c0: i2c@44e0b000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
···
 			status = "disabled";
 		};
 
-		i2c2: i2c@4802a000 {
+		i2c1: i2c@4802a000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
···
 			status = "disabled";
 		};
 
-		i2c3: i2c@4819c000 {
+		i2c2: i2c@4819c000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
···
 		dcan0: d_can@481cc000 {
 			compatible = "bosch,d_can";
 			ti,hwmods = "d_can0";
-			reg = <0x481cc000 0x2000>;
+			reg = <0x481cc000 0x2000
+				0x44e10644 0x4>;
 			interrupts = <52>;
 			status = "disabled";
 		};
···
 		dcan1: d_can@481d0000 {
 			compatible = "bosch,d_can";
 			ti,hwmods = "d_can1";
-			reg = <0x481d0000 0x2000>;
+			reg = <0x481d0000 0x2000
+				0x44e10644 0x4>;
 			interrupts = <55>;
 			status = "disabled";
 		};
 
 		timer1: timer@44e31000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer-1ms";
 			reg = <0x44e31000 0x400>;
 			interrupts = <67>;
 			ti,hwmods = "timer1";
···
 		};
 
 		timer2: timer@48040000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x48040000 0x400>;
 			interrupts = <68>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@48042000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x48042000 0x400>;
 			interrupts = <69>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@48044000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x48044000 0x400>;
 			interrupts = <92>;
 			ti,hwmods = "timer4";
···
 		};
 
 		timer5: timer@48046000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x48046000 0x400>;
 			interrupts = <93>;
 			ti,hwmods = "timer5";
···
 		};
 
 		timer6: timer@48048000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x48048000 0x400>;
 			interrupts = <94>;
 			ti,hwmods = "timer6";
···
 		};
 
 		timer7: timer@4804a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,am335x-timer";
 			reg = <0x4804a000 0x400>;
 			interrupts = <95>;
 			ti,hwmods = "timer7";
···
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x48030000 0x400>;
-			interrupt = <65>;
+			interrupts = <65>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi0";
 			status = "disabled";
···
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x481a0000 0x400>;
-			interrupt = <125>;
+			interrupts = <125>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi1";
 			status = "disabled";

arch/arm/boot/dts/am3517-evm.dts

···
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
 
 / {
 	model = "TI AM3517 EVM (AM3517/05)";

arch/arm/boot/dts/am3517_mt_ventoux.dts

···
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
 
 / {
 	model = "TeeJet Mt.Ventoux";

arch/arm/boot/dts/armada-370-db.dts

···
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <200000000>;
-			status = "okay";
-		};
-		sata@d00a0000 {
-			nr-ports = <2>;
-			status = "okay";
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <0>;
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "rgmii-id";
-		};
-
-		mvsdio@d00d4000 {
-			pinctrl-0 = <&sdio_pins1>;
-			pinctrl-names = "default";
-			/*
-			 * This device is disabled by default, because
-			 * using the SD card connector requires
-			 * changing the default CON40 connector
-			 * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
-			 * different connector
-			 * "DB-88F6710_MPP_RGMII_SD_Jumper".
-			 */
-			status = "disabled";
-			/* No CD or WP GPIOs */
-		};
-
-		usb@d0050000 {
-			status = "okay";
-		};
-
-		usb@d0051000 {
-			status = "okay";
-		};
-
-		spi0: spi@d0010600 {
-			status = "okay";
-
-			spi-flash@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "mx25l25635e";
-				reg = <0>; /* Chip select 0 */
-				spi-max-frequency = <50000000>;
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-			/*
-			 * The two PCIe units are accessible through
-			 * both standard PCIe slots and mini-PCIe
-			 * slots on the board.
-			 */
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <200000000>;
 				status = "okay";
 			};
-			pcie@2,0 {
-				/* Port 1, Lane 0 */
+			sata@a0000 {
+				nr-ports = <2>;
 				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins1>;
+				pinctrl-names = "default";
+				/*
+				 * This device is disabled by default, because
+				 * using the SD card connector requires
+				 * changing the default CON40 connector
+				 * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
+				 * different connector
+				 * "DB-88F6710_MPP_RGMII_SD_Jumper".
+				 */
+				status = "disabled";
+				/* No CD or WP GPIOs */
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb@51000 {
+				status = "okay";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "mx25l25635e";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <50000000>;
+				};
+			};
+
+			pcie-controller {
+				status = "okay";
+				/*
+				 * The two PCIe units are accessible through
+				 * both standard PCIe slots and mini-PCIe
+				 * slots on the board.
+				 */
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
+				pcie@2,0 {
+					/* Port 1, Lane 0 */
+					status = "okay";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-370-mirabox.dts

···
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <200000000>;
-			status = "okay";
-		};
-		timer@d0020300 {
-			clock-frequency = <600000000>;
-			status = "okay";
-		};
-
-		pinctrl {
-			pwr_led_pin: pwr-led-pin {
-				marvell,pins = "mpp63";
-				marvell,function = "gpo";
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
 			};
-
-			stat_led_pins: stat-led-pins {
-				marvell,pins = "mpp64", "mpp65";
-				marvell,function = "gpio";
-			};
-		};
-
-		gpio_leds {
-			compatible = "gpio-leds";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
-
-			green_pwr_led {
-				label = "mirabox:green:pwr";
-				gpios = <&gpio1 31 1>;
-				linux,default-trigger = "heartbeat";
-			};
-
-			blue_stat_led {
-				label = "mirabox:blue:stat";
-				gpios = <&gpio2 0 1>;
-				linux,default-trigger = "cpu0";
-			};
-
-			green_stat_led {
-				label = "mirabox:green:stat";
-				gpios = <&gpio2 1 1>;
-				default-state = "off";
-			};
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <0>;
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "rgmii-id";
-		};
-
-		mvsdio@d00d4000 {
-			pinctrl-0 = <&sdio_pins3>;
-			pinctrl-names = "default";
-			status = "okay";
-			/*
-			 * No CD or WP GPIOs: SDIO interface used for
-			 * Wifi/Bluetooth chip
-			 */
-		};
-
-		usb@d0050000 {
-			status = "okay";
-		};
-
-		usb@d0051000 {
-			status = "okay";
-		};
-
-		i2c@d0011000 {
-			status = "okay";
-			clock-frequency = <100000>;
-			pca9505: pca9505@25 {
-				compatible = "nxp,pca9505";
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x25>;
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-
-			/* Internal mini-PCIe connector */
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
+			timer@20300 {
+				clock-frequency = <600000000>;
 				status = "okay";
 			};
 
-			/* Connected on the PCB to a USB 3.0 XHCI controller */
-			pcie@2,0 {
-				/* Port 1, Lane 0 */
+			pinctrl {
+				pwr_led_pin: pwr-led-pin {
+					marvell,pins = "mpp63";
+					marvell,function = "gpo";
+				};
+
+				stat_led_pins: stat-led-pins {
+					marvell,pins = "mpp64", "mpp65";
+					marvell,function = "gpio";
+				};
+			};
+
+			gpio_leds {
+				compatible = "gpio-leds";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
+
+				green_pwr_led {
+					label = "mirabox:green:pwr";
+					gpios = <&gpio1 31 1>;
+					linux,default-trigger = "heartbeat";
+				};
+
+				blue_stat_led {
+					label = "mirabox:blue:stat";
+					gpios = <&gpio2 0 1>;
+					linux,default-trigger = "cpu0";
+				};
+
+				green_stat_led {
+					label = "mirabox:green:stat";
+					gpios = <&gpio2 1 1>;
+					default-state = "off";
+				};
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+			ethernet@70000 {
 				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins3>;
+				pinctrl-names = "default";
+				status = "okay";
+				/*
+				 * No CD or WP GPIOs: SDIO interface used for
+				 * Wifi/Bluetooth chip
+				 */
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb@51000 {
+				status = "okay";
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+				pca9505: pca9505@25 {
+					compatible = "nxp,pca9505";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x25>;
+				};
+			};
+
+			pcie-controller {
+				status = "okay";
+
+				/* Internal mini-PCIe connector */
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
+
+				/* Connected on the PCB to a USB 3.0 XHCI controller */
+				pcie@2,0 {
+					/* Port 1, Lane 0 */
+					status = "okay";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-370-rd.dts

···
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <200000000>;
-			status = "okay";
-		};
-		sata@d00a0000 {
-			nr-ports = <2>;
-			status = "okay";
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <0>;
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
 			};
 
-			phy1: ethernet-phy@1 {
-				reg = <1>;
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "sgmii";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins1>;
+				pinctrl-names = "default";
+				status = "okay";
+				/* No CD or WP GPIOs */
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb@51000 {
+				status = "okay";
+			};
+
+			gpio-keys {
+				compatible = "gpio-keys";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				button@1 {
+					label = "Software Button";
+					linux,code = <116>;
+					gpios = <&gpio0 6 1>;
+				};
 			};
 		};
-
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "sgmii";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "rgmii-id";
-		};
-
-		mvsdio@d00d4000 {
-			pinctrl-0 = <&sdio_pins1>;
-			pinctrl-names = "default";
-			status = "okay";
-			/* No CD or WP GPIOs */
-		};
-
-		usb@d0050000 {
-			status = "okay";
-		};
-
-		usb@d0051000 {
-			status = "okay";
-		};
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		button@1 {
-			label = "Software Button";
-			linux,code = <116>;
-			gpios = <&gpio0 6 1>;
-		};
-	};
-};
+ };

arch/arm/boot/dts/armada-370-xp.dtsi

···
  * 370 and Armada XP SoC.
  */
 
-/include/ "skeleton.dtsi"
+/include/ "skeleton64.dtsi"
 
 / {
 	model = "Marvell Armada 370 and XP SoC";
···
 		};
 	};
 
-	mpic: interrupt-controller@d0020000 {
-	      compatible = "marvell,mpic";
-	      #interrupt-cells = <1>;
-	      #size-cells = <1>;
-	      interrupt-controller;
-	};
-
-	coherency-fabric@d0020200 {
-		compatible = "marvell,coherency-fabric";
-		reg = <0xd0020200 0xb0>,
-		      <0xd0021810 0x1c>;
-	};
-
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&mpic>;
-		ranges;
+		ranges = <0 0 0xd0000000 0x100000>;
 
-		serial@d0012000 {
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mpic: interrupt-controller@20000 {
+				compatible = "marvell,mpic";
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+			};
+
+			coherency-fabric@20200 {
+				compatible = "marvell,coherency-fabric";
+				reg = <0x20200 0xb0>, <0x21810 0x1c>;
+			};
+
+			serial@12000 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0xd0012000 0x100>;
+				reg = <0x12000 0x100>;
 				reg-shift = <2>;
 				interrupts = <41>;
 				reg-io-width = <1>;
 				status = "disabled";
-		};
-		serial@d0012100 {
+			};
+			serial@12100 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0xd0012100 0x100>;
+				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <42>;
 				reg-io-width = <1>;
 				status = "disabled";
-		};
+			};
 
-		timer@d0020300 {
-			       compatible = "marvell,armada-370-xp-timer";
-			       reg = <0xd0020300 0x30>,
-			       <0xd0021040 0x30>;
-			       interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
-			       clocks = <&coreclk 2>;
-		};
+			timer@20300 {
+				compatible = "marvell,armada-370-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+				clocks = <&coreclk 2>;
+			};
 
-		sata@d00a0000 {
-			compatible = "marvell,orion-sata";
-			reg = <0xd00a0000 0x2400>;
-			interrupts = <55>;
-			clocks = <&gateclk 15>, <&gateclk 30>;
-			clock-names = "0", "1";
-			status = "disabled";
-		};
+			sata@a0000 {
+				compatible = "marvell,orion-sata";
+				reg = <0xa0000 0x2400>;
+				interrupts = <55>;
+				clocks = <&gateclk 15>, <&gateclk 30>;
+				clock-names = "0", "1";
+				status = "disabled";
+			};
 
-		mdio {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "marvell,orion-mdio";
-			reg = <0xd0072004 0x4>;
-		};
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x72004 0x4>;
+			};
 
-		ethernet@d0070000 {
+			ethernet@70000 {
 				compatible = "marvell,armada-370-neta";
-				reg = <0xd0070000 0x2500>;
+				reg = <0x70000 0x2500>;
 				interrupts = <8>;
 				clocks = <&gateclk 4>;
 				status = "disabled";
-		};
+			};
 
-		ethernet@d0074000 {
+			ethernet@74000 {
 				compatible = "marvell,armada-370-neta";
-				reg = <0xd0074000 0x2500>;
+				reg = <0x74000 0x2500>;
 				interrupts = <10>;
 				clocks = <&gateclk 3>;
 				status = "disabled";
-		};
+			};
 
-		i2c0: i2c@d0011000 {
-			compatible = "marvell,mv64xxx-i2c";
-			reg = <0xd0011000 0x20>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <31>;
-			timeout-ms = <1000>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <31>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		i2c1: i2c@d0011100 {
-			compatible = "marvell,mv64xxx-i2c";
-			reg = <0xd0011100 0x20>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <32>;
-			timeout-ms = <1000>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <32>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		rtc@10300 {
-			compatible = "marvell,orion-rtc";
-			reg = <0xd0010300 0x20>;
-			interrupts = <50>;
-		};
+			rtc@10300 {
+				compatible = "marvell,orion-rtc";
+				reg = <0x10300 0x20>;
+				interrupts = <50>;
+			};
 
-		mvsdio@d00d4000 {
-			compatible = "marvell,orion-sdio";
-			reg = <0xd00d4000 0x200>;
-			interrupts = <54>;
-			clocks = <&gateclk 17>;
-			status = "disabled";
-		};
+			mvsdio@d4000 {
+				compatible = "marvell,orion-sdio";
+				reg = <0xd4000 0x200>;
+				interrupts = <54>;
+				clocks = <&gateclk 17>;
+				status = "disabled";
+			};
 
-		usb@d0050000 {
-			compatible = "marvell,orion-ehci";
-			reg = <0xd0050000 0x500>;
-			interrupts = <45>;
-			status = "disabled";
-		};
+			usb@50000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x50000 0x500>;
+				interrupts = <45>;
+				status = "disabled";
+			};
 
-		usb@d0051000 {
-			compatible = "marvell,orion-ehci";
-			reg = <0xd0051000 0x500>;
-			interrupts = <46>;
-			status = "disabled";
-		};
+			usb@51000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x51000 0x500>;
+				interrupts = <46>;
+				status = "disabled";
+			};
 
-		spi0: spi@d0010600 {
-			compatible = "marvell,orion-spi";
-			reg = <0xd0010600 0x28>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <0>;
-			interrupts = <30>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			spi0: spi@10600 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10600 0x28>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <30>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		spi1: spi@d0010680 {
-			compatible = "marvell,orion-spi";
-			reg = <0xd0010680 0x28>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <1>;
-			interrupts = <92>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			spi1: spi@10680 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10680 0x28>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <92>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		devbus-bootcs@d0010400 {
-			compatible = "marvell,mvebu-devbus";
-			reg = <0xd0010400 0x8>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			devbus-bootcs@10400 {
+				compatible = "marvell,mvebu-devbus";
+				reg = <0x10400 0x8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		devbus-cs0@d0010408 {
-			compatible = "marvell,mvebu-devbus";
-			reg = <0xd0010408 0x8>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			devbus-cs0@10408 {
+				compatible = "marvell,mvebu-devbus";
+				reg = <0x10408 0x8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		devbus-cs1@d0010410 {
-			compatible = "marvell,mvebu-devbus";
-			reg = <0xd0010410 0x8>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			devbus-cs1@10410 {
+				compatible = "marvell,mvebu-devbus";
+				reg = <0x10410 0x8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		devbus-cs2@d0010418 {
-			compatible = "marvell,mvebu-devbus";
-			reg = <0xd0010418 0x8>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
-		};
+			devbus-cs2@10418 {
+				compatible = "marvell,mvebu-devbus";
+				reg = <0x10418 0x8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 
-		devbus-cs3@d0010420 {
-			compatible = "marvell,mvebu-devbus";
-			reg = <0xd0010420 0x8>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			clocks = <&coreclk 0>;
-			status = "disabled";
+			devbus-cs3@10420 {
+				compatible = "marvell,mvebu-devbus";
+				reg = <0x10420 0x8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
 		};
 	};
-};
-
+ };

arch/arm/boot/dts/armada-370.dtsi

···
  */
 
 /include/ "armada-370-xp.dtsi"
+/include/ "skeleton.dtsi"
 
 / {
 	model = "Marvell Armada 370 family SoC";
 	compatible = "marvell,armada370", "marvell,armada-370-xp";
-	L2: l2-cache {
-		compatible = "marvell,aurora-outer-cache";
-		reg = <0xd0008000 0x1000>;
-		cache-id-part = <0x100>;
-		wt-override;
-	};
 
 	aliases {
 		gpio0 = &gpio0;
···
 		gpio2 = &gpio2;
 	};
 
-	mpic: interrupt-controller@d0020000 {
-	      reg = <0xd0020a00 0x1d0>,
-		    <0xd0021870 0x58>;
-	};
-
 	soc {
-		system-controller@d0018200 {
+		ranges = <0 0xd0000000 0x100000>;
+		internal-regs {
+			system-controller@18200 {
 				compatible = "marvell,armada-370-xp-system-controller";
-				reg = <0xd0018200 0x100>;
-		};
-
-		pinctrl {
-			compatible = "marvell,mv88f6710-pinctrl";
-			reg = <0xd0018000 0x38>;
-
-			sdio_pins1: sdio-pins1 {
-			      marvell,pins = "mpp9",  "mpp11", "mpp12",
-					     "mpp13", "mpp14", "mpp15";
-			      marvell,function = "sd0";
+				reg = <0x18200 0x100>;
 			};
 
-			sdio_pins2: sdio-pins2 {
-			      marvell,pins = "mpp47", "mpp48", "mpp49",
-					     "mpp50", "mpp51", "mpp52";
-			      marvell,function = "sd0";
+			L2: l2-cache {
+				compatible = "marvell,aurora-outer-cache";
+				reg = <0xd0008000 0x1000>;
+				cache-id-part = <0x100>;
+				wt-override;
 			};
 
-			sdio_pins3: sdio-pins3 {
-			      marvell,pins = "mpp48", "mpp49", "mpp50",
-					     "mpp51", "mpp52", "mpp53";
-			      marvell,function = "sd0";
+			mpic: interrupt-controller@20000 {
+				reg = <0x20a00 0x1d0>, <0x21870 0x58>;
 			};
-	        };
 
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018100 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <82>, <83>, <84>, <85>;
-		};
+			pinctrl {
+				compatible = "marvell,mv88f6710-pinctrl";
+				reg = <0x18000 0x38>;
 
-		gpio1: gpio@d0018140 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018140 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <87>, <88>, <89>, <90>;
-		};
+				sdio_pins1: sdio-pins1 {
+					marvell,pins = "mpp9",  "mpp11", "mpp12",
+							"mpp13", "mpp14", "mpp15";
+					marvell,function = "sd0";
+				};
 
-		gpio2: gpio@d0018180 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018180 0x40>;
-			ngpios = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <91>;
-		};
+				sdio_pins2: sdio-pins2 {
+					marvell,pins = "mpp47", "mpp48", "mpp49",
+							"mpp50", "mpp51", "mpp52";
+					marvell,function = "sd0";
+				};
 
-		coreclk: mvebu-sar@d0018230 {
-			compatible = "marvell,armada-370-core-clock";
-			reg = <0xd0018230 0x08>;
-			#clock-cells = <1>;
-		};
-
-		gateclk: clock-gating-control@d0018220 {
-			compatible = "marvell,armada-370-gating-clock";
-			reg = <0xd0018220 0x4>;
-			clocks = <&coreclk 0>;
-			#clock-cells = <1>;
-		};
-
-		xor@d0060800 {
-			compatible = "marvell,orion-xor";
-			reg = <0xd0060800 0x100
-			       0xd0060A00 0x100>;
-			status = "okay";
-
-			xor00 {
-				interrupts = <51>;
-				dmacap,memcpy;
-				dmacap,xor;
+				sdio_pins3: sdio-pins3 {
+					marvell,pins = "mpp48", "mpp49", "mpp50",
+							"mpp51", "mpp52", "mpp53";
+					marvell,function = "sd0";
+				};
 			};
-			xor01 {
-				interrupts = <52>;
-				dmacap,memcpy;
-				dmacap,xor;
-				dmacap,memset;
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
 			};
-		};
 
-		xor@d0060900 {
-			compatible = "marvell,orion-xor";
-			reg = <0xd0060900 0x100
-			       0xd0060b00 0x100>;
-			status = "okay";
-
-			xor10 {
-				interrupts = <94>;
-				dmacap,memcpy;
-				dmacap,xor;
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <87>, <88>, <89>, <90>;
 			};
-			xor11 {
-				interrupts = <95>;
-				dmacap,memcpy;
-				dmacap,xor;
-				dmacap,memset;
+
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <91>;
 			};
-		};
 
-		usb@d0050000 {
-			clocks = <&coreclk 0>;
-		};
+			coreclk: mvebu-sar@18230 {
+				compatible = "marvell,armada-370-core-clock";
+				reg = <0x18230 0x08>;
+				#clock-cells = <1>;
+			};
 
-		usb@d0051000 {
-			clocks = <&coreclk 0>;
-		};
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-370-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
 
-		thermal@d0018300 {
-			compatible = "marvell,armada370-thermal";
-			reg = <0xd0018300 0x4
-			       0xd0018304 0x4>;
-			status = "okay";
-		};
+			xor@60800 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60800 0x100
+				       0x60A00 0x100>;
+				status = "okay";
 
-		pcie-controller {
-			compatible = "marvell,armada-370-pcie";
-			status = "disabled";
-			device_type = "pci";
+				xor00 {
+					interrupts = <51>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <52>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
 
-			#address-cells = <3>;
-			#size-cells = <2>;
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				status = "okay";
 
-			bus-range = <0x00 0xff>;
+				xor10 {
+					interrupts = <94>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <95>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
 
-			reg = <0xd0040000 0x2000>, <0xd0080000 0x2000>;
+			usb@50000 {
+				clocks = <&coreclk 0>;
+			};
 
-			reg-names = "pcie0.0", "pcie1.0";
+			usb@51000 {
+				clocks = <&coreclk 0>;
+			};
 
-			ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000   /* Port 0.0 registers */
-				  0x82000000 0 0xd0080000 0xd0080000 0 0x00002000   /* Port 1.0 registers */
-				  0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-			          0x81000000 0 0          0xe8000000 0 0x00100000>; /* downstream I/O */
+			thermal@18300 {
+				compatible = "marvell,armada370-thermal";
+				reg = <0x18300 0x4
+					0x18304 0x4>;
+				status = "okay";
+			};
 
-			pcie@1,0 {
+			pcie-controller {
+				compatible = "marvell,armada-370-pcie";
+				status = "disabled";
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
-				reg = <0x0800 0 0 0 0>;
+
 				#address-cells = <3>;
 				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 5>;
-				status = "disabled";
-			};
 
-			pcie@2,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
-				reg = <0x1000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
-				marvell,pcie-port = <1>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 9>;
-				status = "disabled";
+				bus-range = <0x00 0xff>;
+
+				reg = <0x40000 0x2000>, <0x80000 0x2000>;
+
+				reg-names = "pcie0.0", "pcie1.0";
+
+				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
+					0x82000000 0 0x80000 0x80000 0 0x00002000   /* Port 1.0 registers */
+					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+					0x81000000 0 0          0xe8000000 0 0x00100000>; /* downstream I/O */
+
+				pcie@1,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+					reg = <0x0800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 58>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 5>;
+					status = "disabled";
+				};
+
+				pcie@2,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+					reg = <0x1000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 62>;
+					marvell,pcie-port = <1>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 9>;
+					status = "disabled";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp-db.dts

···
 
 	memory {
 		device_type = "memory";
-		reg = <0x00000000 0x80000000>; /* 2 GB */
+		reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012100 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012200 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012300 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-
-		sata@d00a0000 {
-			nr-ports = <2>;
-			status = "okay";
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <0>;
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-
-			phy2: ethernet-phy@2 {
-				reg = <25>;
-			};
-
-			phy3: ethernet-phy@3 {
-				reg = <27>;
-			};
-		};
-
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0030000 {
-			status = "okay";
-			phy = <&phy2>;
-			phy-mode = "sgmii";
-		};
-		ethernet@d0034000 {
-			status = "okay";
-			phy = <&phy3>;
-			phy-mode = "sgmii";
-		};
-
-		mvsdio@d00d4000 {
-			pinctrl-0 = <&sdio_pins>;
-			pinctrl-names = "default";
-			status = "okay";
-			/* No CD or WP GPIOs */
-		};
-
-		usb@d0050000 {
-			status = "okay";
-		};
-
-		usb@d0051000 {
-			status = "okay";
-		};
-
-		usb@d0052000 {
-			status = "okay";
-		};
-
-		spi0: spi@d0010600 {
-			status = "okay";
-
-			spi-flash@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "m25p64";
-				reg = <0>; /* Chip select 0 */
-				spi-max-frequency = <20000000>;
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-
-			/*
-			 * All 6 slots are physically present as
-			 * standard PCIe slots on the board.
-			 */
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@2,0 {
-				/* Port 0, Lane 1 */
+			serial@12100 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@3,0 {
-				/* Port 0, Lane 2 */
+			serial@12200 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@4,0 {
-				/* Port 0, Lane 3 */
+			serial@12300 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@9,0 {
-				/* Port 2, Lane 0 */
+
+			sata@a0000 {
+				nr-ports = <2>;
 				status = "okay";
 			};
-			pcie@10,0 {
-				/* Port 3, Lane 0 */
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <25>;
+				};
+
+				phy3: ethernet-phy@3 {
+					reg = <27>;
+				};
+			};
+
+			ethernet@70000 {
 				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy2>;
+				phy-mode = "sgmii";
+			};
+			ethernet@34000 {
+				status = "okay";
+				phy = <&phy3>;
+				phy-mode = "sgmii";
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				/* No CD or WP GPIOs */
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb@51000 {
+				status = "okay";
+			};
+
+			usb@52000 {
+				status = "okay";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "m25p64";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <20000000>;
+				};
+			};
+
+			pcie-controller {
+				status = "okay";
+
+				/*
+				 * All 6 slots are physically present as
+				 * standard PCIe slots on the board.
+				 */
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
+				pcie@2,0 {
+					/* Port 0, Lane 1 */
+					status = "okay";
+				};
+				pcie@3,0 {
+					/* Port 0, Lane 2 */
+					status = "okay";
+				};
+				pcie@4,0 {
+					/* Port 0, Lane 3 */
+					status = "okay";
+				};
+				pcie@9,0 {
+					/* Port 2, Lane 0 */
+					status = "okay";
+				};
+				pcie@10,0 {
+					/* Port 3, Lane 0 */
+					status = "okay";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp-gp.dts

···
 
 	memory {
 		device_type = "memory";
-
 		/*
-		 * 4 GB of plug-in RAM modules by default but only 3GB
-		 * are visible, the amount of memory available can be
-		 * changed by the bootloader according the size of the
-		 * module actually plugged
+                 * 8 GB of plug-in RAM modules by default.The amount
+                 * of memory available can be changed by the
+                 * bootloader according the size of the module
+                 * actually plugged. Only 7GB are usable because
+                 * addresses from 0xC0000000 to 0xffffffff are used by
+                 * the internal registers of the SoC.
 		 */
-		reg = <0x00000000 0xC0000000>;
+		reg = <0x00000000 0x00000000 0x00000000 0xC0000000>,
+		      <0x00000001 0x00000000 0x00000001 0x00000000>;
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012100 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012200 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012300 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-
-		sata@d00a0000 {
-			nr-ports = <2>;
-			status = "okay";
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <16>;
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <17>;
-			};
-
-			phy2: ethernet-phy@2 {
-				reg = <18>;
-			};
-
-			phy3: ethernet-phy@3 {
-				reg = <19>;
-			};
-		};
-
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0030000 {
-			status = "okay";
-			phy = <&phy2>;
-			phy-mode = "rgmii-id";
-		};
-		ethernet@d0034000 {
-			status = "okay";
-			phy = <&phy3>;
-			phy-mode = "rgmii-id";
-		};
-
-		spi0: spi@d0010600 {
-			status = "okay";
-
-			spi-flash@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "n25q128a13";
-				reg = <0>; /* Chip select 0 */
-				spi-max-frequency = <108000000>;
-			};
-		};
-
-		devbus-bootcs@d0010400 {
-			status = "okay";
-			ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
-
-			/* Device Bus parameters are required */
-
-			/* Read parameters */
-			devbus,bus-width    = <8>;
-			devbus,turn-off-ps  = <60000>;
-			devbus,badr-skew-ps = <0>;
-			devbus,acc-first-ps = <124000>;
-			devbus,acc-next-ps  = <248000>;
-			devbus,rd-setup-ps  = <0>;
-			devbus,rd-hold-ps   = <0>;
-
-			/* Write parameters */
-			devbus,sync-enable = <0>;
-			devbus,wr-high-ps  = <60000>;
-			devbus,wr-low-ps   = <60000>;
-			devbus,ale-wr-ps   = <60000>;
-
-			/* NOR 16 MiB */
-			nor@0 {
-				compatible = "cfi-flash";
-				reg = <0 0x1000000>;
-				bank-width = <2>;
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-
-			/*
-			 * The 3 slots are physically present as
-			 * standard PCIe slots on the board.
-			 */
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@9,0 {
-				/* Port 2, Lane 0 */
+			serial@12100 {
+				clock-frequency = <250000000>;
 				status = "okay";
 			};
-			pcie@10,0 {
-				/* Port 3, Lane 0 */
+			serial@12200 {
+				clock-frequency = <250000000>;
 				status = "okay";
+			};
+			serial@12300 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <16>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <17>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <18>;
+				};
+
+				phy3: ethernet-phy@3 {
+					reg = <19>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy2>;
+				phy-mode = "rgmii-id";
+			};
+			ethernet@34000 {
+				status = "okay";
+				phy = <&phy3>;
+				phy-mode = "rgmii-id";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "n25q128a13";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			devbus-bootcs@10400 {
+				status = "okay";
+				ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
+
+				/* Device Bus parameters are required */
+
+				/* Read parameters */
+				devbus,bus-width    = <8>;
+				devbus,turn-off-ps  = <60000>;
+				devbus,badr-skew-ps = <0>;
+				devbus,acc-first-ps = <124000>;
+				devbus,acc-next-ps  = <248000>;
+				devbus,rd-setup-ps  = <0>;
+				devbus,rd-hold-ps   = <0>;
+
+				/* Write parameters */
+				devbus,sync-enable = <0>;
+				devbus,wr-high-ps  = <60000>;
+				devbus,wr-low-ps   = <60000>;
+				devbus,ale-wr-ps   = <60000>;
+
+				/* NOR 16 MiB */
+				nor@0 {
+					compatible = "cfi-flash";
+					reg = <0 0x1000000>;
+					bank-width = <2>;
+				};
+			};
+
+			pcie-controller {
+				status = "okay";
+
+				/*
+				 * The 3 slots are physically present as
+				 * standard PCIe slots on the board.
+				 */
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
+				pcie@9,0 {
+					/* Port 2, Lane 0 */
+					status = "okay";
+				};
+				pcie@10,0 {
+					/* Port 3, Lane 0 */
+					status = "okay";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp-mv78230.dtsi

···
 	};
 
 	cpus {
-	    #address-cells = <1>;
-	    #size-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	    cpu@0 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <0>;
-		clocks = <&cpuclk 0>;
-	    };
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+		};
 
-	    cpu@1 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <1>;
-		clocks = <&cpuclk 1>;
-	    };
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+		};
 	};
 
 	soc {
-		pinctrl {
-			compatible = "marvell,mv78230-pinctrl";
-			reg = <0xd0018000 0x38>;
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv78230-pinctrl";
+				reg = <0x18000 0x38>;
 
-			sdio_pins: sdio-pins {
-				marvell,pins = "mpp30", "mpp31", "mpp32",
-					       "mpp33", "mpp34", "mpp35";
-				marvell,function = "sd0";
-			};
-		};
-
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018100 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <82>, <83>, <84>, <85>;
-		};
-
-		gpio1: gpio@d0018140 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018140 0x40>;
-			ngpios = <17>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <87>, <88>, <89>;
-		};
-
-		/*
-		 * MV78230 has 2 PCIe units Gen2.0: One unit can be
-		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
-		 */
-		pcie-controller {
-			compatible = "marvell,armada-xp-pcie";
-			status = "disabled";
-			device_type = "pci";
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			bus-range = <0x00 0xff>;
-
-			ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000   /* Port 0.0 registers */
-				  0x82000000 0 0xd0042000 0xd0042000 0 0x00002000   /* Port 2.0 registers */
-				  0x82000000 0 0xd0044000 0xd0044000 0 0x00002000   /* Port 0.1 registers */
-				  0x82000000 0 0xd0048000 0xd0048000 0 0x00002000   /* Port 0.2 registers */
-				  0x82000000 0 0xd004c000 0xd004c000 0 0x00002000   /* Port 0.3 registers */
-				  0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-				  0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-			pcie@1,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
-				reg = <0x0800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 5>;
-				status = "disabled";
+				sdio_pins: sdio-pins {
+					marvell,pins = "mpp30", "mpp31", "mpp32",
+						       "mpp33", "mpp34", "mpp35";
+					marvell,function = "sd0";
+				};
 			};
 
-			pcie@2,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0044000 0 0x2000>;
-				reg = <0x1000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <1>;
-				clocks = <&gateclk 6>;
-				status = "disabled";
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
 			};
 
-			pcie@3,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0048000 0 0x2000>;
-				reg = <0x1800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <2>;
-				clocks = <&gateclk 7>;
-				status = "disabled";
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <87>, <88>, <89>;
 			};
 
-			pcie@4,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd004c000 0 0x2000>;
-				reg = <0x2000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <3>;
-				clocks = <&gateclk 8>;
+			/*
+			 * MV78230 has 2 PCIe units Gen2.0: One unit can be
+			 * configured as x4 or quad x1 lanes. One unit is
+			 * x4/x1.
+			 */
+			pcie-controller {
+				compatible = "marvell,armada-xp-pcie";
 				status = "disabled";
-			};
+				device_type = "pci";
 
-			pcie@9,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0042000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
-				status = "disabled";
+#address-cells = <3>;
+#size-cells = <2>;
+
+				bus-range = <0x00 0xff>;
+
+				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
+					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
+					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
+					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
+					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
+					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
+
+				pcie@1,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+					reg = <0x0800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 58>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 5>;
+					status = "disabled";
+				};
+
+				pcie@2,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+					reg = <0x1000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 59>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <1>;
+					clocks = <&gateclk 6>;
+					status = "disabled";
+				};
+
+				pcie@3,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+					reg = <0x1800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 60>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <2>;
+					clocks = <&gateclk 7>;
+					status = "disabled";
+				};
+
+				pcie@4,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+					reg = <0x2000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 61>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <3>;
+					clocks = <&gateclk 8>;
+					status = "disabled";
+				};
+
+				pcie@9,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+					reg = <0x4800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 99>;
+					marvell,pcie-port = <2>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 26>;
+					status = "disabled";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp-mv78260.dtsi

···
 	};
 
 	cpus {
-	    #address-cells = <1>;
-	    #size-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	    cpu@0 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <0>;
-		clocks = <&cpuclk 0>;
-	    };
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+		};
 
-	    cpu@1 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <1>;
-		clocks = <&cpuclk 1>;
-	    };
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+		};
 	};
 
 	soc {
-		pinctrl {
-			compatible = "marvell,mv78260-pinctrl";
-			reg = <0xd0018000 0x38>;
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv78260-pinctrl";
+				reg = <0x18000 0x38>;
 
-			sdio_pins: sdio-pins {
-				marvell,pins = "mpp30", "mpp31", "mpp32",
-					       "mpp33", "mpp34", "mpp35";
-				marvell,function = "sd0";
+				sdio_pins: sdio-pins {
+					marvell,pins = "mpp30", "mpp31", "mpp32",
+						       "mpp33", "mpp34", "mpp35";
+					marvell,function = "sd0";
+				};
 			};
-		};
 
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018100 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <82>, <83>, <84>, <85>;
-		};
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
 
-		gpio1: gpio@d0018140 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018140 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <87>, <88>, <89>, <90>;
-		};
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <87>, <88>, <89>, <90>;
+			};
 
-		gpio2: gpio@d0018180 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018180 0x40>;
-			ngpios = <3>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <91>;
-		};
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <91>;
+			};
 
-		ethernet@d0034000 {
+			ethernet@34000 {
 				compatible = "marvell,armada-370-neta";
-				reg = <0xd0034000 0x2500>;
+				reg = <0x34000 0x2500>;
 				interrupts = <14>;
 				clocks = <&gateclk 1>;
 				status = "disabled";
-		};
-
-		/*
-		 * MV78260 has 3 PCIe units Gen2.0: Two units can be
-		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
-		 */
-		pcie-controller {
-			compatible = "marvell,armada-xp-pcie";
-			status = "disabled";
-			device_type = "pci";
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			bus-range = <0x00 0xff>;
-
-			ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000   /* Port 0.0 registers */
-				  0x82000000 0 0xd0042000 0xd0042000 0 0x00002000   /* Port 2.0 registers */
-				  0x82000000 0 0xd0044000 0xd0044000 0 0x00002000   /* Port 0.1 registers */
-				  0x82000000 0 0xd0048000 0xd0048000 0 0x00002000   /* Port 0.2 registers */
-				  0x82000000 0 0xd004c000 0xd004c000 0 0x00002000   /* Port 0.3 registers */
-				  0x82000000 0 0xd0080000 0xd0080000 0 0x00002000   /* Port 1.0 registers */
-				  0x82000000 0 0xd0082000 0xd0082000 0 0x00002000   /* Port 3.0 registers */
-				  0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-				  0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-			pcie@1,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
-				reg = <0x0800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 5>;
-				status = "disabled";
 			};
 
-			pcie@2,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0044000 0 0x2000>;
-				reg = <0x1000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <1>;
-				clocks = <&gateclk 6>;
+			/*
+			 * MV78260 has 3 PCIe units Gen2.0: Two units can be
+			 * configured as x4 or quad x1 lanes. One unit is
+			 * x4/x1.
+			 */
+			pcie-controller {
+				compatible = "marvell,armada-xp-pcie";
 				status = "disabled";
-			};
+				device_type = "pci";
 
-			pcie@3,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0048000 0 0x2000>;
-				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <2>;
-				clocks = <&gateclk 7>;
-				status = "disabled";
-			};
 
-			pcie@4,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd004c000 0 0x2000>;
-				reg = <0x2000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <3>;
-				clocks = <&gateclk 8>;
-				status = "disabled";
-			};
+				bus-range = <0x00 0xff>;
 
-			pcie@9,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0042000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
-				status = "disabled";
-			};
+				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
+					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
+					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
+					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
+					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
+					0x82000000 0 0x80000 0x80000 0 0x00002000   /* Port 1.0 registers */
+					0x82000000 0 0x82000 0x82000 0 0x00002000   /* Port 3.0 registers */
+					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
 
-			pcie@10,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0082000 0 0x2000>;
-				reg = <0x5000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
-				marvell,pcie-port = <3>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 27>;
-				status = "disabled";
+				pcie@1,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+					reg = <0x0800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 58>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 5>;
+					status = "disabled";
+				};
+
+				pcie@2,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+					reg = <0x1000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 59>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <1>;
+					clocks = <&gateclk 6>;
+					status = "disabled";
+				};
+
+				pcie@3,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+					reg = <0x1800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 60>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <2>;
+					clocks = <&gateclk 7>;
+					status = "disabled";
+				};
+
+				pcie@4,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+					reg = <0x2000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 61>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <3>;
+					clocks = <&gateclk 8>;
+					status = "disabled";
+				};
+
+				pcie@9,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+					reg = <0x4800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 99>;
+					marvell,pcie-port = <2>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 26>;
+					status = "disabled";
+				};
+
+				pcie@10,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
+					reg = <0x5000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 103>;
+					marvell,pcie-port = <3>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 27>;
+					status = "disabled";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp-mv78460.dtsi

···
 
 
 	cpus {
-	    #address-cells = <1>;
-	    #size-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	    cpu@0 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <0>;
-		clocks = <&cpuclk 0>;
-	    };
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+		};
 
-	    cpu@1 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <1>;
-		clocks = <&cpuclk 1>;
-	    };
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+		};
 
-	    cpu@2 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <2>;
-		clocks = <&cpuclk 2>;
-	    };
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <2>;
+			clocks = <&cpuclk 2>;
+		};
 
-	    cpu@3 {
-		device_type = "cpu";
-		compatible = "marvell,sheeva-v7";
-		reg = <3>;
-		clocks = <&cpuclk 3>;
-	    };
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <3>;
+			clocks = <&cpuclk 3>;
+		};
 	};
 
 	soc {
-		pinctrl {
-			compatible = "marvell,mv78460-pinctrl";
-			reg = <0xd0018000 0x38>;
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv78460-pinctrl";
+				reg = <0x18000 0x38>;
 
-			sdio_pins: sdio-pins {
-				marvell,pins = "mpp30", "mpp31", "mpp32",
-					       "mpp33", "mpp34", "mpp35";
-				marvell,function = "sd0";
+				sdio_pins: sdio-pins {
+					marvell,pins = "mpp30", "mpp31", "mpp32",
+						       "mpp33", "mpp34", "mpp35";
+					marvell,function = "sd0";
+				};
 			};
-		};
 
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018100 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <82>, <83>, <84>, <85>;
-		};
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
 
-		gpio1: gpio@d0018140 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018140 0x40>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <87>, <88>, <89>, <90>;
-		};
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <87>, <88>, <89>, <90>;
+			};
 
-		gpio2: gpio@d0018180 {
-			compatible = "marvell,orion-gpio";
-			reg = <0xd0018180 0x40>;
-			ngpios = <3>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupts-cells = <2>;
-			interrupts = <91>;
-		};
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupts-cells = <2>;
+				interrupts = <91>;
+			};
 
-		ethernet@d0034000 {
+			ethernet@34000 {
 				compatible = "marvell,armada-370-neta";
-				reg = <0xd0034000 0x2500>;
+				reg = <0x34000 0x2500>;
 				interrupts = <14>;
 				clocks = <&gateclk 1>;
 				status = "disabled";
-		};
-
-		/*
-		 * MV78460 has 4 PCIe units Gen2.0: Two units can be
-		 * configured as x4 or quad x1 lanes. Two units are
-		 * x4/x1.
-		 */
-		pcie-controller {
-			compatible = "marvell,armada-xp-pcie";
-			status = "disabled";
-			device_type = "pci";
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			bus-range = <0x00 0xff>;
-
-			ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000   /* Port 0.0 registers */
-				  0x82000000 0 0xd0042000 0xd0042000 0 0x00002000   /* Port 2.0 registers */
-				  0x82000000 0 0xd0044000 0xd0044000 0 0x00002000   /* Port 0.1 registers */
-				  0x82000000 0 0xd0048000 0xd0048000 0 0x00002000   /* Port 0.2 registers */
-				  0x82000000 0 0xd004c000 0xd004c000 0 0x00002000   /* Port 0.3 registers */
-				  0x82000000 0 0xd0080000 0xd0080000 0 0x00002000   /* Port 1.0 registers */
-				  0x82000000 0 0xd0082000 0xd0082000 0 0x00002000   /* Port 3.0 registers */
-				  0x82000000 0 0xd0084000 0xd0084000 0 0x00002000   /* Port 1.1 registers */
-				  0x82000000 0 0xd0088000 0xd0088000 0 0x00002000   /* Port 1.2 registers */
-				  0x82000000 0 0xd008c000 0xd008c000 0 0x00002000   /* Port 1.3 registers */
-				  0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-				  0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-			pcie@1,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
-				reg = <0x0800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 5>;
-				status = "disabled";
 			};
 
-			pcie@2,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82001000 0 0xd0044000 0 0x2000>;
-				reg = <0x1000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <1>;
-				clocks = <&gateclk 6>;
+			/*
+			 * MV78460 has 4 PCIe units Gen2.0: Two units can be
+			 * configured as x4 or quad x1 lanes. Two units are
+			 * x4/x1.
+			 */
+			pcie-controller {
+				compatible = "marvell,armada-xp-pcie";
 				status = "disabled";
-			};
+				device_type = "pci";
 
-			pcie@3,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82001800 0 0xd0048000 0 0x2000>;
-				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <2>;
-				clocks = <&gateclk 7>;
-				status = "disabled";
-			};
 
-			pcie@4,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82002000 0 0xd004c000 0 0x2000>;
-				reg = <0x2000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
-				marvell,pcie-port = <0>;
-				marvell,pcie-lane = <3>;
-				clocks = <&gateclk 8>;
-				status = "disabled";
-			};
+				bus-range = <0x00 0xff>;
 
-			pcie@5,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
-				reg = <0x2800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
-				marvell,pcie-port = <1>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 9>;
-				status = "disabled";
-			};
+				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
+					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
+					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
+					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
+					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
+					0x82000000 0 0x80000 0x80000 0 0x00002000   /* Port 1.0 registers */
+					0x82000000 0 0x82000 0x82000 0 0x00002000   /* Port 3.0 registers */
+					0x82000000 0 0x84000 0x84000 0 0x00002000   /* Port 1.1 registers */
+					0x82000000 0 0x88000 0x88000 0 0x00002000   /* Port 1.2 registers */
+					0x82000000 0 0x8c000 0x8c000 0 0x00002000   /* Port 1.3 registers */
+					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
 
-			pcie@6,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82003000 0 0xd0084000 0 0x2000>;
-				reg = <0x3000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
-				marvell,pcie-port = <1>;
-				marvell,pcie-lane = <1>;
-				clocks = <&gateclk 10>;
-				status = "disabled";
-			};
+				pcie@1,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+					reg = <0x0800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 58>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 5>;
+					status = "disabled";
+				};
 
-			pcie@7,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82003800 0 0xd0088000 0 0x2000>;
-				reg = <0x3800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
-				marvell,pcie-port = <1>;
-				marvell,pcie-lane = <2>;
-				clocks = <&gateclk 11>;
-				status = "disabled";
-			};
+				pcie@2,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+					reg = <0x1000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 59>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <1>;
+					clocks = <&gateclk 6>;
+					status = "disabled";
+				};
 
-			pcie@8,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82004000 0 0xd008c000 0 0x2000>;
-				reg = <0x4000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
-				marvell,pcie-port = <1>;
-				marvell,pcie-lane = <3>;
-				clocks = <&gateclk 12>;
-				status = "disabled";
-			};
-			pcie@9,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82004800 0 0xd0042000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
-				status = "disabled";
-			};
+				pcie@3,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+					reg = <0x1800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 60>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <2>;
+					clocks = <&gateclk 7>;
+					status = "disabled";
+				};
 
-			pcie@10,0 {
-				device_type = "pci";
-				assigned-addresses = <0x82005000 0 0xd0082000 0 0x2000>;
-				reg = <0x5000 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				#interrupt-cells = <1>;
-				ranges;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
-				marvell,pcie-port = <3>;
-				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 27>;
-				status = "disabled";
+				pcie@4,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+					reg = <0x2000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 61>;
+					marvell,pcie-port = <0>;
+					marvell,pcie-lane = <3>;
+					clocks = <&gateclk 8>;
+					status = "disabled";
+				};
+
+				pcie@5,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+					reg = <0x2800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 62>;
+					marvell,pcie-port = <1>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 9>;
+					status = "disabled";
+				};
+
+				pcie@6,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+					reg = <0x3000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 63>;
+					marvell,pcie-port = <1>;
+					marvell,pcie-lane = <1>;
+					clocks = <&gateclk 10>;
+					status = "disabled";
+				};
+
+				pcie@7,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+					reg = <0x3800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 64>;
+					marvell,pcie-port = <1>;
+					marvell,pcie-lane = <2>;
+					clocks = <&gateclk 11>;
+					status = "disabled";
+				};
+
+				pcie@8,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+					reg = <0x4000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 65>;
+					marvell,pcie-port = <1>;
+					marvell,pcie-lane = <3>;
+					clocks = <&gateclk 12>;
+					status = "disabled";
+				};
+				pcie@9,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+					reg = <0x4800 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 99>;
+					marvell,pcie-port = <2>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 26>;
+					status = "disabled";
+				};
+
+				pcie@10,0 {
+					device_type = "pci";
+					assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+					reg = <0x5000 0 0 0 0>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					#interrupt-cells = <1>;
+					ranges;
+					interrupt-map-mask = <0 0 0 0>;
+					interrupt-map = <0 0 0 0 &mpic 103>;
+					marvell,pcie-port = <3>;
+					marvell,pcie-lane = <0>;
+					clocks = <&gateclk 27>;
+					status = "disabled";
+				};
 			};
 		};
 	};
- };
+};

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

···
 
 	memory {
 		device_type = "memory";
-		reg = <0x00000000 0xC0000000>; /* 3 GB */
+		reg = <0 0x00000000 0 0xC0000000>; /* 3 GB */
 	};
 
 	soc {
-		serial@d0012000 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		serial@d0012100 {
-			clock-frequency = <250000000>;
-			status = "okay";
-		};
-		pinctrl {
-			led_pins: led-pins-0 {
-				marvell,pins = "mpp49", "mpp51", "mpp53";
-				marvell,function = "gpio";
-			};
-		};
-		leds {
-			compatible = "gpio-leds";
-			pinctrl-names = "default";
-			pinctrl-0 = <&led_pins>;
-
-			red_led {
-				label = "red_led";
-				gpios = <&gpio1 17 1>;
-				default-state = "off";
-			};
-
-			yellow_led {
-				label = "yellow_led";
-				gpios = <&gpio1 19 1>;
-				default-state = "off";
-			};
-
-			green_led {
-				label = "green_led";
-				gpios = <&gpio1 21 1>;
-				default-state = "off";
-				linux,default-trigger = "heartbeat";
-			};
-		};
-
-		gpio_keys {
-			compatible = "gpio-keys";
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			button@1 {
-				label = "Init Button";
-				linux,code = <116>;
-				gpios = <&gpio1 28 0>;
-			};
-		};
-
-		mdio {
-			phy0: ethernet-phy@0 {
-				reg = <0>;
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-
-			phy2: ethernet-phy@2 {
-				reg = <2>;
-			};
-
-			phy3: ethernet-phy@3 {
-				reg = <3>;
-			};
-		};
-
-		ethernet@d0070000 {
-			status = "okay";
-			phy = <&phy0>;
-			phy-mode = "sgmii";
-		};
-		ethernet@d0074000 {
-			status = "okay";
-			phy = <&phy1>;
-			phy-mode = "sgmii";
-		};
-		ethernet@d0030000 {
-			status = "okay";
-			phy = <&phy2>;
-			phy-mode = "sgmii";
-		};
-		ethernet@d0034000 {
-			status = "okay";
-			phy = <&phy3>;
-			phy-mode = "sgmii";
-		};
-		i2c@d0011000 {
-			status = "okay";
-			clock-frequency = <400000>;
-		};
-		i2c@d0011100 {
-			status = "okay";
-			clock-frequency = <400000>;
-
-			s35390a: s35390a@30 {
-				compatible = "s35390a";
-				reg = <0x30>;
-			};
-		};
-		sata@d00a0000 {
-			nr-ports = <2>;
-			status = "okay";
-		};
-		usb@d0050000 {
-			status = "okay";
-		};
-		usb@d0051000 {
-			status = "okay";
-		};
-
-		devbus-bootcs@d0010400 {
-			status = "okay";
-			ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
-
-			/* Device Bus parameters are required */
-
-			/* Read parameters */
-			devbus,bus-width    = <8>;
-			devbus,turn-off-ps  = <60000>;
-			devbus,badr-skew-ps = <0>;
-			devbus,acc-first-ps = <124000>;
-			devbus,acc-next-ps  = <248000>;
-			devbus,rd-setup-ps  = <0>;
-			devbus,rd-hold-ps   = <0>;
-
-			/* Write parameters */
-			devbus,sync-enable = <0>;
-			devbus,wr-high-ps  = <60000>;
-			devbus,wr-low-ps   = <60000>;
-			devbus,ale-wr-ps   = <60000>;
-
-			/* NOR 128 MiB */
-			nor@0 {
-				compatible = "cfi-flash";
-				reg = <0 0x8000000>;
-				bank-width = <2>;
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-			/* Internal mini-PCIe connector */
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <250000000>;
 				status = "okay";
+			};
+			serial@12100 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+			pinctrl {
+				led_pins: led-pins-0 {
+					marvell,pins = "mpp49", "mpp51", "mpp53";
+					marvell,function = "gpio";
+				};
+			};
+			leds {
+				compatible = "gpio-leds";
+				pinctrl-names = "default";
+				pinctrl-0 = <&led_pins>;
+
+				red_led {
+					label = "red_led";
+					gpios = <&gpio1 17 1>;
+					default-state = "off";
+				};
+
+				yellow_led {
+					label = "yellow_led";
+					gpios = <&gpio1 19 1>;
+					default-state = "off";
+				};
+
+				green_led {
+					label = "green_led";
+					gpios = <&gpio1 21 1>;
+					default-state = "off";
+					linux,default-trigger = "heartbeat";
+				};
+			};
+
+			gpio_keys {
+				compatible = "gpio-keys";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				button@1 {
+					label = "Init Button";
+					linux,code = <116>;
+					gpios = <&gpio1 28 0>;
+				};
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+
+				phy3: ethernet-phy@3 {
+					reg = <3>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "sgmii";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "sgmii";
+			};
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy2>;
+				phy-mode = "sgmii";
+			};
+			ethernet@34000 {
+				status = "okay";
+				phy = <&phy3>;
+				phy-mode = "sgmii";
+			};
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <400000>;
+			};
+			i2c@11100 {
+				status = "okay";
+				clock-frequency = <400000>;
+
+				s35390a: s35390a@30 {
+					compatible = "s35390a";
+					reg = <0x30>;
+				};
+			};
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+			usb@50000 {
+				status = "okay";
+			};
+			usb@51000 {
+				status = "okay";
+			};
+
+			devbus-bootcs@10400 {
+				status = "okay";
+				ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
+
+				/* Device Bus parameters are required */
+
+				/* Read parameters */
+				devbus,bus-width    = <8>;
+				devbus,turn-off-ps  = <60000>;
+				devbus,badr-skew-ps = <0>;
+				devbus,acc-first-ps = <124000>;
+				devbus,acc-next-ps  = <248000>;
+				devbus,rd-setup-ps  = <0>;
+				devbus,rd-hold-ps   = <0>;
+
+				/* Write parameters */
+				devbus,sync-enable = <0>;
+				devbus,wr-high-ps  = <60000>;
+				devbus,wr-low-ps   = <60000>;
+				devbus,ale-wr-ps   = <60000>;
+
+				/* NOR 128 MiB */
+				nor@0 {
+					compatible = "cfi-flash";
+					reg = <0 0x8000000>;
+					bank-width = <2>;
+				};
+			};
+
+			pcie-controller {
+				status = "okay";
+				/* Internal mini-PCIe connector */
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-xp.dtsi

···
 	model = "Marvell Armada XP family SoC";
 	compatible = "marvell,armadaxp", "marvell,armada-370-xp";
 
-	L2: l2-cache {
-		compatible = "marvell,aurora-system-cache";
-		reg = <0xd0008000 0x1000>;
-		cache-id-part = <0x100>;
-		wt-override;
-	};
-
-	mpic: interrupt-controller@d0020000 {
-	      reg = <0xd0020a00 0x2d0>,
-		    <0xd0021070 0x58>;
-	};
-
-	armada-370-xp-pmsu@d0022000 {
-		compatible = "marvell,armada-370-xp-pmsu";
-		reg = <0xd0022100 0x430>,
-		      <0xd0020800 0x20>;
-	};
-
 	soc {
-		serial@d0012200 {
+		internal-regs {
+			L2: l2-cache {
+				compatible = "marvell,aurora-system-cache";
+				reg = <0x08000 0x1000>;
+				cache-id-part = <0x100>;
+				wt-override;
+			};
+
+			mpic: interrupt-controller@20000 {
+			      reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+			};
+
+			armada-370-xp-pmsu@22000 {
+				compatible = "marvell,armada-370-xp-pmsu";
+				reg = <0x22100 0x430>, <0x20800 0x20>;
+			};
+
+			serial@12200 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0xd0012200 0x100>;
+				reg = <0x12200 0x100>;
 				reg-shift = <2>;
 				interrupts = <43>;
 				reg-io-width = <1>;
 				status = "disabled";
-		};
-		serial@d0012300 {
+			};
+			serial@12300 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0xd0012300 0x100>;
+				reg = <0x12300 0x100>;
 				reg-shift = <2>;
 				interrupts = <44>;
 				reg-io-width = <1>;
 				status = "disabled";
-		};
+			};
 
-		timer@d0020300 {
+			timer@20300 {
 				marvell,timer-25Mhz;
-		};
+			};
 
-		coreclk: mvebu-sar@d0018230 {
-			compatible = "marvell,armada-xp-core-clock";
-			reg = <0xd0018230 0x08>;
-			#clock-cells = <1>;
-		};
+			coreclk: mvebu-sar@18230 {
+				compatible = "marvell,armada-xp-core-clock";
+				reg = <0x18230 0x08>;
+				#clock-cells = <1>;
+			};
 
-		cpuclk: clock-complex@d0018700 {
-			#clock-cells = <1>;
-			compatible = "marvell,armada-xp-cpu-clock";
-			reg = <0xd0018700 0xA0>;
-			clocks = <&coreclk 1>;
-		};
+			cpuclk: clock-complex@18700 {
+				#clock-cells = <1>;
+				compatible = "marvell,armada-xp-cpu-clock";
+				reg = <0x18700 0xA0>;
+				clocks = <&coreclk 1>;
+			};
 
-		gateclk: clock-gating-control@d0018220 {
-			compatible = "marvell,armada-xp-gating-clock";
-			reg = <0xd0018220 0x4>;
-			clocks = <&coreclk 0>;
-			#clock-cells = <1>;
-		};
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-xp-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
 
-		system-controller@d0018200 {
+			system-controller@18200 {
 				compatible = "marvell,armada-370-xp-system-controller";
-				reg = <0xd0018200 0x500>;
-		};
+				reg = <0x18200 0x500>;
+			};
 
-		ethernet@d0030000 {
+			ethernet@30000 {
 				compatible = "marvell,armada-370-neta";
-				reg = <0xd0030000 0x2500>;
+				reg = <0x30000 0x2500>;
 				interrupts = <12>;
 				clocks = <&gateclk 2>;
 				status = "disabled";
-		};
-
-		xor@d0060900 {
-			compatible = "marvell,orion-xor";
-			reg = <0xd0060900 0x100
-			       0xd0060b00 0x100>;
-			clocks = <&gateclk 22>;
-			status = "okay";
-
-			xor10 {
-				interrupts = <51>;
-				dmacap,memcpy;
-				dmacap,xor;
 			};
-			xor11 {
-				interrupts = <52>;
-				dmacap,memcpy;
-				dmacap,xor;
-				dmacap,memset;
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <51>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <52>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
 			};
-		};
 
-		xor@d00f0900 {
-			compatible = "marvell,orion-xor";
-			reg = <0xd00F0900 0x100
-			       0xd00F0B00 0x100>;
-			clocks = <&gateclk 28>;
-			status = "okay";
+			xor@f0900 {
+				compatible = "marvell,orion-xor";
+				reg = <0xF0900 0x100
+				       0xF0B00 0x100>;
+				clocks = <&gateclk 28>;
+				status = "okay";
 
-			xor00 {
-				interrupts = <94>;
-				dmacap,memcpy;
-				dmacap,xor;
+				xor00 {
+					interrupts = <94>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <95>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
 			};
-			xor01 {
-				interrupts = <95>;
-				dmacap,memcpy;
-				dmacap,xor;
-				dmacap,memset;
+
+			usb@50000 {
+				clocks = <&gateclk 18>;
 			};
-		};
 
-		usb@d0050000 {
-			clocks = <&gateclk 18>;
-		};
+			usb@51000 {
+				clocks = <&gateclk 19>;
+			};
 
-		usb@d0051000 {
-			clocks = <&gateclk 19>;
-		};
+			usb@52000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x52000 0x500>;
+				interrupts = <47>;
+				clocks = <&gateclk 20>;
+				status = "disabled";
+			};
 
-		usb@d0052000 {
-			compatible = "marvell,orion-ehci";
-			reg = <0xd0052000 0x500>;
-			interrupts = <47>;
-			clocks = <&gateclk 20>;
-			status = "disabled";
-		};
-
-		thermal@d00182b0 {
-			compatible = "marvell,armadaxp-thermal";
-			reg = <0xd00182b0 0x4
-			       0xd00184d0 0x4>;
-			status = "okay";
+			thermal@182b0 {
+				compatible = "marvell,armadaxp-thermal";
+				reg = <0x182b0 0x4
+					0x184d0 0x4>;
+				status = "okay";
+			};
 		};
 	};
 };

arch/arm/boot/dts/cros5250-common.dtsi

···
 	chosen {
 	};
 
+	pinctrl@11400000 {
+		/*
+		 * Disabled pullups since external part has its own pullups and
+		 * double-pulling gets us out of spec in some cases.
+		 */
+		i2c2_bus: i2c2-bus {
+			samsung,pin-pud = <0>;
+		};
+	};
+
 	i2c@12C60000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <378000>;
-		gpios = <&gpb3 0 2 3 0>,
-			<&gpb3 1 2 3 0>;
 
 		max77686@09 {
 			compatible = "maxim,max77686";
···
 	i2c@12C70000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <378000>;
-		gpios = <&gpb3 2 2 3 0>,
-			<&gpb3 3 2 3 0>;
 	};
 
 	i2c@12C80000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
-
-		/*
-		 * Disabled pullups since external part has its own pullups and
-		 * double-pulling gets us out of spec in some cases.
-		 */
-		gpios = <&gpa0 6 3 0 0>,
-			<&gpa0 7 3 0 0>;
 
 		hdmiddc@50 {
 			compatible = "samsung,exynos5-hdmiddc";
···
 	i2c@12C90000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
-		gpios = <&gpa1 2 3 3 0>,
-			<&gpa1 3 3 3 0>;
 	};
 
 	i2c@12CA0000 {
-		status = "disabled";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
 	};
 
 	i2c@12CB0000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
-		gpios = <&gpa2 2 3 3 0>,
-			<&gpa2 3 3 3 0>;
 	};
 
 	i2c@12CC0000 {
···
 	i2c@12CD0000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
-		gpios = <&gpb2 2 3 3 0>,
-			<&gpb2 3 3 3 0>;
 	};
 
 	i2c@12CE0000 {
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <8>;
-			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
-				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
-				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
-				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
-				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
 		};
 	};
 
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <4>;
-			samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
-			wp-gpios = <&gpc2 1 0 0 3>;
-			gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
-				<&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
-				<&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>;
+			wp-gpios = <&gpc2 1 0>;
 		};
 	};
 
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		/* See board-specific dts files for pin setup */
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <4>;
-			/* See board-specific dts files for GPIOs */
 		};
 	};
 
···
 	};
 
 	spi_1: spi@12d30000 {
-		gpios = <&gpa2 4 2 3 0>,
-			<&gpa2 6 2 3 0>,
-			<&gpa2 7 2 3 0>;
 		samsung,spi-src-clk = <0>;
 		num-cs = <1>;
 	};
···
 	};
 
 	hdmi {
-		hpd-gpio = <&gpx3 7 0xf 1 3>;
+		hpd-gpio = <&gpx3 7 0>;
 	};
 
 	gpio-keys {
···
 
 		power {
 			label = "Power";
-			gpios = <&gpx1 3 0 0x10000 0>;
+			gpios = <&gpx1 3 1>;
 			linux,code = <116>; /* KEY_POWER */
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/da850-evm.dts

···
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmc0_pins>;
 		};
+		spi1: spi@1f0e000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
+			flash: m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "m25p64";
+				spi-max-frequency = <30000000>;
+				reg = <0>;
+				partition@0 {
+					label = "U-Boot-SPL";
+					reg = <0x00000000 0x00010000>;
+					read-only;
+				};
+				partition@1 {
+					label = "U-Boot";
+					reg = <0x00010000 0x00080000>;
+					read-only;
+				};
+				partition@2 {
+					label = "U-Boot-Env";
+					reg = <0x00090000 0x00010000>;
+					read-only;
+				};
+				partition@3 {
+					label = "Kernel";
+					reg = <0x000a0000 0x00280000>;
+				};
+				partition@4 {
+					label = "Filesystem";
+					reg = <0x00320000 0x00400000>;
+				};
+				partition@5 {
+					label = "MAC-Address";
+					reg = <0x007f0000 0x00010000>;
+					read-only;
+				};
+			};
+		};
 	};
 	nand_cs3@62000000 {
 		status = "okay";

arch/arm/boot/dts/da850.dtsi

···
 					0x28 0x00222222  0x00ffffff
 				>;
 			};
+			ehrpwm0a_pins: pinmux_ehrpwm0a_pins {
+				pinctrl-single,bits = <
+					/* EPWM0A */
+					0xc 0x00000002 0x0000000f
+				>;
+			};
+			ehrpwm0b_pins: pinmux_ehrpwm0b_pins {
+				pinctrl-single,bits = <
+					/* EPWM0B */
+					0xc 0x00000020 0x000000f0
+				>;
+			};
+			ehrpwm1a_pins: pinmux_ehrpwm1a_pins {
+				pinctrl-single,bits = <
+					/* EPWM1A */
+					0x14 0x00000002 0x0000000f
+				>;
+			};
+			ehrpwm1b_pins: pinmux_ehrpwm1b_pins {
+				pinctrl-single,bits = <
+					/* EPWM1B */
+					0x14 0x00000020 0x000000f0
+				>;
+			};
+			ecap0_pins: pinmux_ecap0_pins {
+				pinctrl-single,bits = <
+					/* ECAP0_APWM0 */
+					0x8 0x20000000 0xf0000000
+				>;
+			};
+			ecap1_pins: pinmux_ecap1_pins {
+				pinctrl-single,bits = <
+					/* ECAP1_APWM1 */
+					0x4 0x40000000 0xf0000000
+				>;
+			};
+			ecap2_pins: pinmux_ecap2_pins {
+				pinctrl-single,bits = <
+					/* ECAP2_APWM2 */
+					0x4 0x00000004 0x0000000f
+				>;
+			};
+			spi1_pins: pinmux_spi_pins {
+				pinctrl-single,bits = <
+					/* SIMO, SOMI, CLK */
+					0x14 0x00110100 0x00ff0f00
+				>;
+			};
+			spi1_cs0_pin: pinmux_spi1_cs0 {
+				pinctrl-single,bits = <
+					/* CS0 */
+					0x14 0x00000010 0x000000f0
+				>;
+			};
 		};
 		serial0: serial@1c42000 {
 			compatible = "ns16550a";
···
 			compatible = "ti,da830-mmc";
 			reg = <0x40000 0x1000>;
 			interrupts = <16>;
+			status = "disabled";
+		};
+		ehrpwm0: ehrpwm@01f00000 {
+			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			#pwm-cells = <3>;
+			reg = <0x300000 0x2000>;
+			status = "disabled";
+		};
+		ehrpwm1: ehrpwm@01f02000 {
+			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			#pwm-cells = <3>;
+			reg = <0x302000 0x2000>;
+			status = "disabled";
+		};
+		ecap0: ecap@01f06000 {
+			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			#pwm-cells = <3>;
+			reg = <0x306000 0x80>;
+			status = "disabled";
+		};
+		ecap1: ecap@01f07000 {
+			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			#pwm-cells = <3>;
+			reg = <0x307000 0x80>;
+			status = "disabled";
+		};
+		ecap2: ecap@01f08000 {
+			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			#pwm-cells = <3>;
+			reg = <0x308000 0x80>;
+			status = "disabled";
+		};
+		spi1: spi@1f0e000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "ti,da830-spi";
+			reg = <0x30e000 0x1000>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <1>;
+			interrupts = <56>;
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/exynos4.dtsi

···
 		i2c7 = &i2c_7;
 	};
 
+	chipid@10000000 {
+		compatible = "samsung,exynos4210-chipid";
+		reg = <0x10000000 0x100>;
+	};
+
 	pd_mfc: mfc-power-domain@10023C40 {
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023C40 0x20>;
···
 		#interrupt-cells = <2>;
 		interrupt-controller;
 		reg = <0x10440000 0x1000>;
+	};
+
+	sys_reg: sysreg {
+		compatible = "samsung,exynos4-sysreg", "syscon";
+		reg = <0x10010000 0x400>;
 	};
 
 	watchdog@10060000 {
···
 		interrupts = <0 58 0>;
 		clocks = <&clock 317>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_bus>;
 		status = "disabled";
 	};
 
···
 		interrupts = <0 59 0>;
 		clocks = <&clock 318>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_bus>;
 		status = "disabled";
 	};
 
···
 		#size-cells = <0>;
 		clocks = <&clock 327>, <&clock 159>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0_bus>;
 		status = "disabled";
 	};
 
···
 		#size-cells = <0>;
 		clocks = <&clock 328>, <&clock 160>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi1_bus>;
 		status = "disabled";
 	};
 
···
 		#size-cells = <0>;
 		clocks = <&clock 329>, <&clock 161>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_bus>;
 		status = "disabled";
 	};
 
···
 			#dma-channels = <8>;
 			#dma-requests = <1>;
 		};
+	};
+
+	fimd: fimd@11c00000 {
+		compatible = "samsung,exynos4210-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x11c00000 0x20000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <11 0>, <11 1>, <11 2>;
+		clocks = <&clock 140>, <&clock 283>;
+		clock-names = "sclk_fimd", "fimd";
+		samsung,power-domain = <&pd_lcd0>;
+		status = "disabled";
 	};
 };

arch/arm/boot/dts/exynos4210-origen.dts

···
 		status = "okay";
 	};
 
+	g2d@12800000 {
+		status = "okay";
+	};
+
 	codec@13400000 {
 		samsung,mfc-r = <0x43000000 0x800000>;
 		samsung,mfc-l = <0x51000000 0x800000>;

arch/arm/boot/dts/exynos4210-smdkv310.dts

···
 	};
 
 	sdhci@12530000 {
-		samsung,sdhci-bus-width = <4>;
-		linux,mmc_cap_4_bit_data;
-		samsung,sdhci-cd-internal;
-		gpio-cd = <&gpk2 2 2 3 3>;
-		gpios = <&gpk2 0 2 0 3>,
-			<&gpk2 1 2 0 3>,
-			<&gpk2 3 2 3 3>,
-			<&gpk2 4 2 3 3>,
-			<&gpk2 5 2 3 3>,
-			<&gpk2 6 2 3 3>;
+		bus-width = <4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+		status = "okay";
+	};
+
+	g2d@12800000 {
 		status = "okay";
 	};
 
···
 		status = "okay";
 	};
 
+	pinctrl@11000000 {
+		keypad_rows: keypad-rows {
+			samsung,pins = "gpx2-0", "gpx2-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		keypad_cols: keypad-cols {
+			samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+				       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
 	keypad@100A0000 {
 		samsung,keypad-num-rows = <2>;
 		samsung,keypad-num-columns = <8>;
 		linux,keypad-no-autorepeat;
 		linux,keypad-wakeup;
+		pinctrl-names = "default";
+		pinctrl-0 = <&keypad_rows &keypad_cols>;
 		status = "okay";
-
-		row-gpios = <&gpx2 0 3 3 0>,
-			    <&gpx2 1 3 3 0>;
-
-		col-gpios = <&gpx1 0 3 0 0>,
-			    <&gpx1 1 3 0 0>,
-			    <&gpx1 2 3 0 0>,
-			    <&gpx1 3 3 0 0>,
-			    <&gpx1 4 3 0 0>,
-			    <&gpx1 5 3 0 0>,
-			    <&gpx1 6 3 0 0>,
-			    <&gpx1 7 3 0 0>;
 
 		key_1 {
 			keypad,row = <0>;
···
 		#address-cells = <1>;
 		#size-cells = <0>;
 		samsung,i2c-sda-delay = <100>;
-		samsung,i2c-max-bus-freq = <20000>;
-		gpios = <&gpd1 0 2 3 0>,
-			<&gpd1 1 2 3 0>;
+		samsung,i2c-max-bus-freq = <100000>;
 		status = "okay";
 
 		eeprom@50 {
···
 	};
 
 	spi_2: spi@13940000 {
-		gpios = <&gpc1 1 5 3 0>,
-			<&gpc1 3 5 3 0>,
-			<&gpc1 4 5 3 0>;
 		status = "okay";
 
 		w25x80@0 {
···
 			spi-max-frequency = <1000000>;
 
 			controller-data {
-				cs-gpio = <&gpc1 2 1 0 3>;
+				cs-gpio = <&gpc1 2 0>;
 				samsung,spi-feedback-delay = <0>;
 			};
 

arch/arm/boot/dts/exynos4210.dtsi

···
 		reg = <0x100C0000 0x100>;
 		interrupts = <2 4>;
 	};
+
+	g2d@12800000 {
+		compatible = "samsung,s5pv210-g2d";
+		reg = <0x12800000 0x1000>;
+		interrupts = <0 89 0>;
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos4412-origen.dts

···
 		status = "okay";
 	};
 
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing {
+			clock-frequency = <50000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hfront-porch = <64>;
+			hback-porch = <16>;
+			hsync-len = <48>;
+			vback-porch = <64>;
+			vfront-porch = <16>;
+			vsync-len = <3>;
+		};
+	};
+
 	serial@13800000 {
 		status = "okay";
 	};

arch/arm/boot/dts/exynos4412-smdk4412.dts

···
 		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
 	};
 
+	g2d@10800000 {
+		status = "okay";
+	};
+
+	g2d@10800000 {
+		status = "okay";
+	};
+
 	sdhci@12530000 {
 		bus-width = <4>;
 		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;

arch/arm/boot/dts/exynos4412.dtsi

···
 					<0x7 0 &gic 1 12 0>;
 		};
 	};
+
+	mshc@12550000 {
+		compatible = "samsung,exynos4412-dw-mshc";
+		reg = <0x12550000 0x1000>;
+		interrupts = <0 77 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
 };

arch/arm/boot/dts/exynos4x12.dtsi

···
 		reg = <0x106E0000 0x1000>;
 		interrupts = <0 72 0>;
 	};
+
+	g2d@10800000 {
+		compatible = "samsung,exynos4212-g2d";
+		reg = <0x10800000 0x1000>;
+		interrupts = <0 89 0>;
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos5250-arndale.dts

···
 		bootargs = "console=ttySAC2,115200";
 	};
 
+	codec@11000000 {
+		samsung,mfc-r = <0x43000000 0x800000>;
+		samsung,mfc-l = <0x51000000 0x800000>;
+	};
+
 	i2c@12C60000 {
-		status = "disabled";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <20000>;
+		samsung,i2c-slave-addr = <0x66>;
+
+		s5m8767_pmic@66 {
+			compatible = "samsung,s5m8767-pmic";
+			reg = <0x66>;
+
+			s5m8767,pmic-buck2-dvs-voltage = <1300000>;
+			s5m8767,pmic-buck3-dvs-voltage = <1100000>;
+			s5m8767,pmic-buck4-dvs-voltage = <1200000>;
+			s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 0>,
+							<&gpd1 1 0>,
+							<&gpd1 2 0>;
+			s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>,
+							<&gpx2 4 0>,
+							<&gpx2 5 0>;
+			regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "VDD_ALIVE_1.0V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "VDD_28IO_DP_1.35V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VDD_COMMON1_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VDD_IOPERI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					op_mode = <1>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VDD_EXT_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VDD_MPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VDD_XPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VDD_COMMON2_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "VDD_33ON_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					op_mode = <1>;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VDD_COMMON3_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "VDD_ABB2_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "VDD_USB_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "VDDQ_C2C_W_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "VDD18_ABB0_3_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "VDD10_COMMON4_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VDD18_HSIC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "VDDQ_MMC2_3_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo18_reg: LDO18 {
+					regulator-name = "VDD_33ON_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					op_mode = <1>;
+				};
+
+				ldo22_reg: LDO22 {
+					regulator-name = "EXT_33_OFF";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					op_mode = <1>;
+				};
+
+				ldo23_reg: LDO23 {
+					regulator-name = "EXT_28_OFF";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					op_mode = <1>;
+				};
+
+				ldo25_reg: LDO25 {
+					regulator-name = "PVDD_LDO25";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					op_mode = <1>;
+				};
+
+				ldo26_reg: LDO26 {
+					regulator-name = "EXT_18_OFF";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					op_mode = <1>;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "vdd_mif";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <925000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "vdd_int";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "vdd_g3d";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "VDD_MEM_1.35V";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1355000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck9_reg: BUCK9 {
+					regulator-name = "VDD_33_OFF_EXT1";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <3000000>;
+					op_mode = <1>;
+				};
+			};
+		};
 	};
 
 	i2c@12C70000 {
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		vmmc-supply = <&mmc_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <8>;
-			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
-				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
-				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>,
-				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
-				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>;
 		};
 	};
 
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		vmmc-supply = <&mmc_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <4>;
-			samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
-			gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
-				<&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
-				<&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>;
+			disable-wp;
 		};
 	};
 
···
 
 	spi_2: spi@12d40000 {
 		status = "disabled";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		menu {
+			label = "SW-TACT2";
+			gpios = <&gpx1 4 1>;
+			linux,code = <139>;
+			gpio-key,wakeup;
+		};
+
+		home {
+			label = "SW-TACT3";
+			gpios = <&gpx1 5 1>;
+			linux,code = <102>;
+			gpio-key,wakeup;
+		};
+
+		up {
+			label = "SW-TACT4";
+			gpios = <&gpx1 6 1>;
+			linux,code = <103>;
+			gpio-key,wakeup;
+		};
+
+		down {
+			label = "SW-TACT5";
+			gpios = <&gpx1 7 1>;
+			linux,code = <108>;
+			gpio-key,wakeup;
+		};
+
+		back {
+			label = "SW-TACT6";
+			gpios = <&gpx2 0 1>;
+			linux,code = <158>;
+			gpio-key,wakeup;
+		};
+
+		wakeup {
+			label = "SW-TACT7";
+			gpios = <&gpx2 1 1>;
+			linux,code = <143>;
+			gpio-key,wakeup;
+		};
+	};
+
+	hdmi {
+		hpd-gpio = <&gpx3 7 2>;
+		vdd_osc-supply = <&ldo10_reg>;
+		vdd_pll-supply = <&ldo8_reg>;
+		vdd-supply = <&ldo8_reg>;
+	};
+
+	mmc_reg: voltage-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_33ON_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpx1 1 1>;
+		enable-active-high;
+	};
+
+	reg_hdmi_en: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi-en";
 	};
 
 	fixed-rate-clocks {

arch/arm/boot/dts/exynos5250-pinctrl.dtsi

···
+/*
+ * Samsung's Exynos5250 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos5250 SoC pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/ {
+	pinctrl@11400000 {
+		gpa0: gpa0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpa1: gpa1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpa2: gpa2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb0: gpb0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb1: gpb1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb2: gpb2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb3: gpb3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc0: gpc0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc1: gpc1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc2: gpc2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc3: gpc3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd0: gpd0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd1: gpd1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy1: gpy1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy2: gpy2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy3: gpy3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy4: gpy4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy5: gpy5 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy6: gpy6 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpc4: gpc4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&combiner>;
+			#interrupt-cells = <2>;
+			interrupts = <23 0>, <24 0>, <25 0>, <25 1>,
+				     <26 0>, <26 1>, <27 0>, <27 1>;
+		};
+
+		gpx1: gpx1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&combiner>;
+			#interrupt-cells = <2>;
+			interrupts = <28 0>, <28 1>, <29 0>, <29 1>,
+				     <30 0>, <30 1>, <31 0>, <31 1>;
+		};
+
+		gpx2: gpx2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpx3: gpx3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c2_hs_bus: i2c2-hs-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		uart2_data: uart2-data {
+			samsung,pins = "gpa1-0", "gpa1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart2_fctl: uart2-fctl {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c3_bus: i2c3-bus {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c3_hs_bus: i2c3-hs-bus {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		uart3_data: uart3-data {
+			samsung,pins = "gpa1-4", "gpa1-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi0_bus: spi0-bus {
+			samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c4_bus: i2c4-bus {
+			samsung,pins = "gpa2-0", "gpa2-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c5_bus: i2c5-bus {
+			samsung,pins = "gpa2-2", "gpa2-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		spi1_bus: spi1-bus {
+			samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s1_bus: i2s1-bus {
+			samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+					"gpb0-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm1_bus: pcm1-bus {
+			samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+					"gpb0-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		ac97_bus: ac97-bus {
+			samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+					"gpb0-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s2_bus: i2s2-bus {
+			samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
+					"gpb1-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm2_bus: pcm2-bus {
+			samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
+					"gpb1-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spdif_bus: spdif-bus {
+			samsung,pins = "gpb1-0", "gpb1-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi2_bus: spi2-bus {
+			samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
+			samsung,pin-function = <5>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c6_bus: i2c6-bus {
+			samsung,pins = "gpb1-3", "gpb1-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c7_bus: i2c7-bus {
+			samsung,pins = "gpb2-2", "gpb2-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c0_bus: i2c0-bus {
+			samsung,pins = "gpb3-0", "gpb3-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c1_bus: i2c1-bus {
+			samsung,pins = "gpb3-2", "gpb3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c0_hs_bus: i2c0-hs-bus {
+			samsung,pins = "gpb3-0", "gpb3-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		i2c1_hs_bus: i2c1-hs-bus {
+			samsung,pins = "gpb3-2", "gpb3-3";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		sd0_clk: sd0-clk {
+			samsung,pins = "gpc0-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd0_cmd: sd0-cmd {
+			samsung,pins = "gpc0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd0_cd: sd0-cd {
+			samsung,pins = "gpc0-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd0_bus1: sd0-bus-width1 {
+			samsung,pins = "gpc0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd0_bus4: sd0-bus-width4 {
+			samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5", "gpc0-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd0_bus8: sd0-bus-width8 {
+			samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd1_clk: sd1-clk {
+			samsung,pins = "gpc2-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd1_cmd: sd1-cmd {
+			samsung,pins = "gpc2-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd1_cd: sd1-cd {
+			samsung,pins = "gpc2-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd1_bus1: sd1-bus-width1 {
+			samsung,pins = "gpc2-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd1_bus4: sd1-bus-width4 {
+			samsung,pins = "gpc2-3", "gpc2-4", "gpc2-5", "gpc2-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_clk: sd2-clk {
+			samsung,pins = "gpc3-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_cmd: sd2-cmd {
+			samsung,pins = "gpc3-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_cd: sd2-cd {
+			samsung,pins = "gpc3-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_bus1: sd2-bus-width1 {
+			samsung,pins = "gpc3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_bus4: sd2-bus-width4 {
+			samsung,pins = "gpc3-3", "gpc3-4", "gpc3-5", "gpc3-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd2_bus8: sd2-bus-width8 {
+			samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd3_clk: sd3-clk {
+			samsung,pins = "gpc4-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd3_cmd: sd3-cmd {
+			samsung,pins = "gpc4-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd3_cd: sd3-cd {
+			samsung,pins = "gpc4-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd3_bus1: sd3-bus-width1 {
+			samsung,pins = "gpc4-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		sd3_bus4: sd3-bus-width4 {
+			samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <3>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpd0-0", "gpd0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpd0-2", "gpd0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@13400000 {
+		gpe0: gpe0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe1: gpe1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf0: gpf0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf1: gpf1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpg0: gpg0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpg1: gpg1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpg2: gpg2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gph0: gph0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gph1: gph1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		cam_gpio_a: cam-gpio-a {
+			samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+				       "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+				       "gpe1-0", "gpe1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		cam_gpio_b: cam-gpio-b {
+			samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
+				       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_i2c2_bus: cam-i2c2-bus {
+			samsung,pins = "gpe0-6", "gpe1-0";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_spi1_bus: cam-spi1-bus {
+			samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_i2c1_bus: cam-i2c1-bus {
+			samsung,pins = "gpf0-2", "gpf0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_i2c0_bus: cam-i2c0-bus {
+			samsung,pins = "gpf0-0", "gpf0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_spi0_bus: cam-spi0-bus {
+			samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_bayrgb_bus: cam-bayrgb-bus {
+			samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
+				       "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
+				       "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
+				       "gpg1-4", "gpg1-5", "gpg1-6", "gpg1-7",
+				       "gpg2-0", "gpg2-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		cam_port_a: cam-port-a {
+			samsung,pins = "gph0-0", "gph0-1", "gph0-2", "gph0-3",
+				       "gph1-0", "gph1-1", "gph1-2", "gph1-3",
+				       "gph1-4", "gph1-5", "gph1-6", "gph1-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@10d10000 {
+		gpv0: gpv0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpv1: gpv1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpv2: gpv2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpv3: gpv3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpv4: gpv4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		c2c_rxd: c2c-rxd {
+			samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
+				       "gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
+				       "gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
+				       "gpv1-4", "gpv1-5", "gpv1-6", "gpv1-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+
+		c2c_txd: c2c-txd {
+			samsung,pins = "gpv2-0", "gpv2-1", "gpv2-2", "gpv2-3",
+				       "gpv2-4", "gpv2-5", "gpv2-6", "gpv2-7",
+				       "gpv3-0", "gpv3-1", "gpv3-2", "gpv3-3",
+				       "gpv3-4", "gpv3-5", "gpv3-6", "gpv3-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@03680000 {
+		gpz: gpz {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		i2s0_bus: i2s0-bus {
+			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+					"gpz-4", "gpz-5", "gpz-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+};

arch/arm/boot/dts/exynos5250-smdk5250.dts

···
 	i2c@12C60000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <20000>;
-		gpios = <&gpb3 0 2 3 0>,
-			<&gpb3 1 2 3 0>;
 
 		eeprom@50 {
 			compatible = "samsung,s524ad0xd1";
···
 	i2c@12C70000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <20000>;
-		gpios = <&gpb3 2 2 3 0>,
-			<&gpb3 3 2 3 0>;
 
 		eeprom@51 {
 			compatible = "samsung,s524ad0xd1";
···
 	i2c@12C80000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
-		gpios = <&gpa0 6 3 3 0>,
-			<&gpa0 7 3 3 0>;
 
 		hdmiddc@50 {
 			compatible = "samsung,exynos5-hdmiddc";
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <8>;
-			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
-				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
-				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
-				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
-				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
 		};
 	};
 
···
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <4>;
-			samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
 			disable-wp;
-			gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
-				<&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
-				<&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>,
-				<&gpc4 3 3 3 3>, <&gpc4 3 3 3 3>,
-				<&gpc4 5 3 3 3>, <&gpc4 6 3 3 3>;
 		};
 	};
 
···
 	};
 
 	spi_1: spi@12d30000 {
-		gpios = <&gpa2 4 2 3 0>,
-			<&gpa2 6 2 3 0>,
-			<&gpa2 7 2 3 0>;
-
 		w25q80bw@0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
···
 			spi-max-frequency = <1000000>;
 
 			controller-data {
-				cs-gpio = <&gpa2 5 1 0 3>;
+				cs-gpio = <&gpa2 5 0>;
 				samsung,spi-feedback-delay = <0>;
 			};
 
···
 	};
 
 	hdmi {
-		hpd-gpio = <&gpx3 7 0xf 1 3>;
+		hpd-gpio = <&gpx3 7 0>;
 	};
 
 	codec@11000000 {
···
 	};
 
 	i2s0: i2s@03830000 {
-		gpios = <&gpz 0 2 0 0>, <&gpz 1 2 0 0>, <&gpz 2 2 0 0>,
-			<&gpz 3 2 0 0>, <&gpz 4 2 0 0>, <&gpz 5 2 0 0>,
-			<&gpz 6 2 0 0>;
+		status = "okay";
 	};
 
 	i2s1: i2s@12D60000 {
···
 		samsung,color-depth = <1>;
 		samsung,link-rate = <0x0a>;
 		samsung,lane-count = <4>;
+	};
+
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing@0 {
+			/* 1280x800 */
+			clock-frequency = <50000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <4>;
+			hback-porch = <4>;
+			hsync-len = <4>;
+			vback-porch = <4>;
+			vfront-porch = <4>;
+			vsync-len = <4>;
+		};
 	};
 
 	fixed-rate-clocks {

arch/arm/boot/dts/exynos5250-snow.dts

···
 	model = "Google Snow";
 	compatible = "google,snow", "samsung,exynos5250";
 
+	aliases {
+		i2c104 = &i2c_104;
+	};
+
+	pinctrl@11400000 {
+		sd3_clk: sd3-clk {
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_cmd: sd3-cmd {
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_bus4: sd3-bus-width4 {
+			samsung,pin-drv = <0>;
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
 		lid-switch {
 			label = "Lid";
-			gpios = <&gpx3 5 0 0x10000 0>;
+			gpios = <&gpx3 5 1>;
 			linux,input-type = <5>; /* EV_SW */
 			linux,code = <0>; /* SW_LID */
 			debounce-interval = <1>;
 			gpio-key,wakeup;
+		};
+	};
+
+	i2c-arbitrator {
+		compatible = "i2c-arb-gpio-challenge";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@12CA0000}>;
+
+		our-claim-gpio = <&gpf0 3 1>;
+		their-claim-gpios = <&gpe0 4 1>;
+		slew-delay-us = <10>;
+		wait-retry-us = <3000>;
+		wait-free-us = <50000>;
+
+		/* Use ID 104 as a hint that we're on physical bus 4 */
+		i2c_104: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			battery: sbs-battery@b {
+				compatible = "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,poll-retry-count = <1>;
+			};
+
+			ec: embedded-controller {
+				compatible = "google,cros-ec-i2c";
+				reg = <0x1e>;
+				interrupts = <6 0>;
+				interrupt-parent = <&gpx1>;
+				wakeup-source;
+
+				keyboard-controller {
+				        compatible = "google,cros-ec-keyb";
+				        keypad,num-rows = <8>;
+				        keypad,num-columns = <13>;
+				        google,needs-ghost-filter;
+					linux,keymap = <0x0001003a	/* CAPSLK */
+							0x0002003b	/* F1 */
+							0x00030030	/* B */
+							0x00040044	/* F10 */
+							0x00060031	/* N */
+							0x0008000d	/* = */
+							0x000a0064	/* R_ALT */
+
+							0x01010001	/* ESC */
+							0x0102003e	/* F4 */
+							0x01030022	/* G */
+							0x01040041	/* F7 */
+							0x01060023	/* H */
+							0x01080028	/* ' */
+							0x01090043	/* F9 */
+							0x010b000e	/* BKSPACE */
+
+							0x0200001d	/* L_CTRL */
+							0x0201000f	/* TAB */
+							0x0202003d	/* F3 */
+							0x02030014	/* T */
+							0x02040040	/* F6 */
+							0x0205001b	/* ] */
+							0x02060015	/* Y */
+							0x02070056	/* 102ND */
+							0x0208001a	/* [ */
+							0x02090042	/* F8 */
+
+							0x03010029	/* GRAVE */
+							0x0302003c	/* F2 */
+							0x03030006	/* 5 */
+							0x0304003f	/* F5 */
+							0x03060007	/* 6 */
+							0x0308000c	/* - */
+							0x030b002b	/* \ */
+
+							0x04000061	/* R_CTRL */
+							0x0401001e	/* A */
+							0x04020020	/* D */
+							0x04030021	/* F */
+							0x0404001f	/* S */
+							0x04050025	/* K */
+							0x04060024	/* J */
+							0x04080027	/* ; */
+							0x04090026	/* L */
+							0x040b001c	/* ENTER */
+
+							0x0501002c	/* Z */
+							0x0502002e	/* C */
+							0x0503002f	/* V */
+							0x0504002d	/* X */
+							0x05050033	/* , */
+							0x05060032	/* M */
+							0x0507002a	/* L_SHIFT */
+							0x05080035	/* / */
+							0x05090034	/* . */
+							0x050B0039	/* SPACE */
+
+							0x06010002	/* 1 */
+							0x06020004	/* 3 */
+							0x06030005	/* 4 */
+							0x06040003	/* 2 */
+							0x06050009	/* 8 */
+							0x06060008	/* 7 */
+							0x0608000b	/* 0 */
+							0x0609000a	/* 9 */
+							0x060a0038	/* L_ALT */
+							0x060b006c	/* DOWN */
+							0x060c006a	/* RIGHT */
+
+							0x07010010	/* Q */
+							0x07020012	/* E */
+							0x07030013	/* R */
+							0x07040011	/* W */
+							0x07050017	/* I */
+							0x07060016	/* U */
+							0x07070036	/* R_SHIFT */
+							0x07080019	/* P */
+							0x07090018	/* O */
+							0x070b0067	/* UP */
+							0x070c0069>;	/* LEFT */
+				};
+			};
 		};
 	};
 
···
 	 */
 	dwmmc3@12230000 {
 		slot@0 {
-			gpios = <&gpc4 0 2 0 0>, <&gpc4 1 2 3 0>,
-				<&gpc4 3 2 3 0>, <&gpc4 4 2 3 0>,
-				<&gpc4 5 2 3 0>, <&gpc4 6 2 3 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
 		};
 	};
 

arch/arm/boot/dts/exynos5250.dtsi

···
 */
 
 /include/ "skeleton.dtsi"
+/include/ "exynos5250-pinctrl.dtsi"
 
 / {
 	compatible = "samsung,exynos5250";
···
 		i2c6 = &i2c_6;
 		i2c7 = &i2c_7;
 		i2c8 = &i2c_8;
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+		pinctrl3 = &pinctrl_3;
+	};
+
+	chipid@10000000 {
+		compatible = "samsung,exynos4210-chipid";
+		reg = <0x10000000 0x100>;
 	};
 
 	pd_gsc: gsc-power-domain@0x10044000 {
···
 	};
 
 	gic:interrupt-controller@10481000 {
-		compatible = "arm,cortex-a9-gic";
+		compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
-		reg = <0x10481000 0x1000>, <0x10482000 0x2000>;
+		reg = <0x10481000 0x1000>,
+		      <0x10482000 0x1000>,
+		      <0x10484000 0x2000>,
+		      <0x10486000 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 13 0xf08>,
+			     <1 14 0xf08>,
+			     <1 11 0xf08>,
+			     <1 10 0xf08>;
 	};
 
 	combiner:interrupt-controller@10440000 {
···
 		compatible = "arm,cortex-a15-pmu";
 		interrupt-parent = <&combiner>;
 		interrupts = <1 2>, <22 4>;
+	};
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,exynos5250-pinctrl";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 46 0>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupts = <0 32 0>;
+		};
+	};
+
+	pinctrl_1: pinctrl@13400000 {
+		compatible = "samsung,exynos5250-pinctrl";
+		reg = <0x13400000 0x1000>;
+		interrupts = <0 45 0>;
+	};
+
+	pinctrl_2: pinctrl@10d10000 {
+		compatible = "samsung,exynos5250-pinctrl";
+		reg = <0x10d10000 0x1000>;
+		interrupts = <0 50 0>;
+	};
+
+	pinctrl_3: pinctrl@03680000 {
+		compatible = "samsung,exynos5250-pinctrl";
+		reg = <0x0368000 0x1000>;
+		interrupts = <0 47 0>;
 	};
 
 	watchdog {
···
 		#size-cells = <0>;
 		clocks = <&clock 294>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_bus>;
 	};
 
 	i2c_1: i2c@12C70000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 295>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_bus>;
 	};
 
 	i2c_2: i2c@12C80000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 296>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_bus>;
 	};
 
 	i2c_3: i2c@12C90000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 297>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c3_bus>;
 	};
 
 	i2c_4: i2c@12CA0000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 298>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c4_bus>;
 	};
 
 	i2c_5: i2c@12CB0000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 299>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c5_bus>;
 	};
 
 	i2c_6: i2c@12CC0000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 300>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c6_bus>;
 	};
 
 	i2c_7: i2c@12CD0000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 301>;
 		clock-names = "i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c7_bus>;
 	};
 
 	i2c_8: i2c@12CE0000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 304>, <&clock 154>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0_bus>;
 	};
 
 	spi_1: spi@12d30000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 305>, <&clock 155>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi1_bus>;
 	};
 
 	spi_2: spi@12d40000 {
···
 		#size-cells = <0>;
 		clocks = <&clock 306>, <&clock 156>;
 		clock-names = "spi", "spi_busclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_bus>;
 	};
 
 	dwmmc_0: dwmmc0@12200000 {
···
 		samsung,supports-rstclr;
 		samsung,supports-secdai;
 		samsung,idma-addr = <0x03000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_bus>;
 	};
 
 	i2s1: i2s@12D60000 {
···
 		dmas = <&pdma1 12
 			&pdma1 11>;
 		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s1_bus>;
 	};
 
 	i2s2: i2s@12D70000 {
···
 		dmas = <&pdma0 12
 			&pdma0 11>;
 		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s2_bus>;
 	};
 
 	usb@12110000 {
 		compatible = "samsung,exynos4210-ehci";
 		reg = <0x12110000 0x100>;
 		interrupts = <0 71 0>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};
 
 	usb@12120000 {
 		compatible = "samsung,exynos4210-ohci";
 		reg = <0x12120000 0x100>;
 		interrupts = <0 71 0>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};
 
 	amba {
···
 			#dma-requests = <1>;
 		};
 	};
-
-	gpio-controllers {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		gpio-controller;
-		ranges;
-
-		gpa0: gpio-controller@11400000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpa1: gpio-controller@11400020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpa2: gpio-controller@11400040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400040 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb0: gpio-controller@11400060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb1: gpio-controller@11400080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb2: gpio-controller@114000A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb3: gpio-controller@114000C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc0: gpio-controller@114000E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc1: gpio-controller@11400100 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400100 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc2: gpio-controller@11400120 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400120 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc3: gpio-controller@11400140 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400140 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc4: gpio-controller@114002E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114002E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd0: gpio-controller@11400160 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400160 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd1: gpio-controller@11400180 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400180 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy0: gpio-controller@114001A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy1: gpio-controller@114001C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy2: gpio-controller@114001E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy3: gpio-controller@11400200 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400200 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy4: gpio-controller@11400220 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400220 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy5: gpio-controller@11400240 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400240 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy6: gpio-controller@11400260 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400260 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx0: gpio-controller@11400C00 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400C00 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx1: gpio-controller@11400C20 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400C20 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx2: gpio-controller@11400C40 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400C40 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx3: gpio-controller@11400C60 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400C60 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe0: gpio-controller@13400000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe1: gpio-controller@13400020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf0: gpio-controller@13400040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400040 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf1: gpio-controller@13400060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpg0: gpio-controller@13400080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpg1: gpio-controller@134000A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x134000A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpg2: gpio-controller@134000C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x134000C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gph0: gpio-controller@134000E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x134000E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gph1: gpio-controller@13400100 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x13400100 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpv0: gpio-controller@10D10000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x10D10000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpv1: gpio-controller@10D10020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x10D10020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpv2: gpio-controller@10D10040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x10D10060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpv3: gpio-controller@10D10060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x10D10080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpv4: gpio-controller@10D10080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x10D100C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpz: gpio-controller@03860000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x03860000 0x20>;
-			#gpio-cells = <4>;
-		};
-	};
-
 
 	gsc_0:  gsc@0x13e00000 {
 		compatible = "samsung,exynos5-gsc";
···
 			reg = <0x10040720>;
 			samsung,enable-mask = <1>;
 		};
+	};
+
+	fimd {
+		compatible = "samsung,exynos5250-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x14400000 0x40000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <18 4>, <18 5>, <18 6>;
+		clocks = <&clock 133>, <&clock 339>;
+		clock-names = "sclk_fimd", "fimd";
 	};
 };

arch/arm/boot/dts/exynos5440-sd5v1.dts

···
+/*
+ * SAMSUNG SD5v1 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos5440.dtsi"
+
+/ {
+	model = "SAMSUNG SD5v1 board based on EXYNOS5440";
+	compatible = "samsung,sd5v1", "samsung,exynos5440";
+
+	chosen {
+		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
+	};
+
+	fixed-rate-clocks {
+		xtal {
+			compatible = "samsung,clock-xtal";
+			clock-frequency = <50000000>;
+		};
+	};
+
+	gmac: ethernet@00230000 {
+		fixed_phy;
+		phy_addr = <1>;
+	};
+
+	spi {
+		status = "disabled";
+	};
+
+};

arch/arm/boot/dts/exynos5440-ssdk5440.dts

···
 	model = "SAMSUNG SSDK5440 board based on EXYNOS5440";
 	compatible = "samsung,ssdk5440", "samsung,exynos5440";
 
-	memory {
-		reg = <0x80000000 0x80000000>;
-	};
-
 	chosen {
-		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x81000000,8M console=ttySAC0,115200 init=/linuxrc";
+		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
 	};
 
 	spi {

arch/arm/boot/dts/exynos5440.dtsi

···
 		compatible = "arm,cortex-a15-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
-		reg = <0x2E1000 0x1000>, <0x2E2000 0x1000>;
+		reg =	<0x2E1000 0x1000>,
+			<0x2E2000 0x1000>,
+			<0x2E4000 0x2000>,
+			<0x2E6000 0x2000>;
+		interrupts = <1 9 0xf04>;
 	};
 
 	cpus {
···
 		};
 	};
 
+	arm-pmu {
+		compatible = "arm,cortex-a15-pmu", "arm,cortex-a9-pmu";
+		interrupts = <0 52 4>,
+			     <0 53 4>,
+			     <0 54 4>,
+			     <0 55 4>;
+	};
+
 	timer {
 		compatible = "arm,cortex-a15-timer",
 			     "arm,armv7-timer";
···
 			     <1 11 0xf08>,
 			     <1 10 0xf08>;
 		clock-frequency = <50000000>;
+	};
+
+	cpufreq@160000 {
+		compatible = "samsung,exynos5440-cpufreq";
+		reg = <0x160000 0x1000>;
+		interrupts = <0 57 0>;
+		operating-points = <
+				/* KHz	  uV */
+				1200000 1025000
+				1000000 975000
+				800000  925000
+		>;
 	};
 
 	serial@B0000 {
···
 	pinctrl {
 		compatible = "samsung,exynos5440-pinctrl";
 		reg = <0xE0000 0x1000>;
+		interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>,
+			     <0 41 0>, <0 42 0>, <0 43 0>, <0 44 0>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		#gpio-cells = <2>;
···
 		clock-names = "watchdog";
 	};
 
+	gmac: ethernet@00230000 {
+		compatible = "snps,dwmac-3.70a";
+		reg = <0x00230000 0x8000>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 31 4>;
+		interrupt-names = "macirq";
+		phy-mode = "sgmii";
+		clocks = <&clock 25>;
+		clock-names = "stmmaceth";
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;
···
 		interrupt-parent = <&gic>;
 		ranges;
 
-		pdma0: pdma@121A0000 {
+		pdma0: pdma@00121000 {
 			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x120000 0x1000>;
-			interrupts = <0 34 0>;
-			clocks = <&clock 21>;
+			reg = <0x121000 0x1000>;
+			interrupts = <0 46 0>;
+			clocks = <&clock 8>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
 			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@121B0000 {
+		pdma1: pdma@00120000 {
 			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x121000 0x1000>;
-			interrupts = <0 35 0>;
-			clocks = <&clock 21>;
+			reg = <0x120000 0x1000>;
+			interrupts = <0 47 0>;
+			clocks = <&clock 8>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;

arch/arm/boot/dts/imx23-evk.dts

···
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a>;
-				panel-enable-gpios = <&gpio1 18 0>;
+				lcd-supply = <&reg_lcd_3v3>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <9200000>;
+							hactive = <480>;
+							vactive = <272>;
+							hback-porch = <15>;
+							hfront-porch = <8>;
+							vback-porch = <12>;
+							vfront-porch = <4>;
+							hsync-len = <1>;
+							vsync-len = <1>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <0>;
+						};
+					};
+				};
 			};
 		};
 
···
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			gpio = <&gpio1 29 0>;
+		};
+
+		reg_lcd_3v3: lcd-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 18 0>;
+			enable-active-high;
 		};
 	};
 

arch/arm/boot/dts/imx23-olinuxino.dts

···
 				pinctrl-names = "default";
 				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
 				bus-width = <4>;
+				broken-cd;
 				status = "okay";
 			};
 

arch/arm/boot/dts/imx23.dtsi

···
 				reg = <0x80000000 0x2000>;
 			};
 
-			dma-apbh@80004000 {
+			dma_apbh: dma-apbh@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
+				interrupts = <0 14 20 0
+					      13 13 13 13>;
+				interrupt-names = "empty", "ssp0", "ssp1", "empty",
+						  "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+				#dma-cells = <1>;
+				dma-channels = <8>;
 				clocks = <&clks 15>;
 			};
 
···
 				interrupt-names = "gpmi-dma", "bch";
 				clocks = <&clks 34>;
 				clock-names = "gpmi_io";
+				dmas = <&dma_apbh 4>;
+				dma-names = "rx-tx";
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
···
 				reg = <0x80010000 0x2000>;
 				interrupts = <15 14>;
 				clocks = <&clks 33>;
+				dmas = <&dma_apbh 1>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
···
 				status = "disabled";
 			};
 
-			dma-apbx@80024000 {
+			dma_apbx: dma-apbx@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
+				interrupts = <7 5 9 26
+					      19 0 25 23
+					      60 58 9 0
+					      0 0 0 0>;
+				interrupt-names = "audio-adc", "audio-dac", "spdif-tx", "i2c",
+						  "saif0", "empty", "auart0-rx", "auart0-tx",
+						  "auart1-rx", "auart1-tx", "saif1", "empty",
+						  "empty", "empty", "empty", "empty";
+				#dma-cells = <1>;
+				dma-channels = <16>;
 				clocks = <&clks 16>;
 			};
 
···
 				reg = <0x80034000 0x2000>;
 				interrupts = <2 20>;
 				clocks = <&clks 33>;
+				dmas = <&dma_apbh 2>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
···
 
 			saif0: saif@80042000 {
 				reg = <0x80042000 0x2000>;
+				dmas = <&dma_apbx 4>;
+				dma-names = "rx-tx";
 				status = "disabled";
 			};
 
···
 
 			saif1: saif@80046000 {
 				reg = <0x80046000 0x2000>;
+				dmas = <&dma_apbx 10>;
+				dma-names = "rx-tx";
 				status = "disabled";
 			};
 
 			audio-out@80048000 {
 				reg = <0x80048000 0x2000>;
+				dmas = <&dma_apbx 1>;
+				dma-names = "tx";
 				status = "disabled";
 			};
 
 			audio-in@8004c000 {
 				reg = <0x8004c000 0x2000>;
+				dmas = <&dma_apbx 0>;
+				dma-names = "rx";
 				status = "disabled";
 			};
 
···
 
 			spdif@80054000 {
 				reg = <0x80054000 2000>;
+				dmas = <&dma_apbx 2>;
+				dma-names = "tx";
 				status = "disabled";
 			};
 
 			i2c@80058000 {
 				reg = <0x80058000 0x2000>;
+				dmas = <&dma_apbx 3>;
+				dma-names = "rx-tx";
 				status = "disabled";
 			};
 
···
 				reg = <0x8006c000 0x2000>;
 				interrupts = <24 25 23>;
 				clocks = <&clks 32>;
+				dmas = <&dma_apbx 6>, <&dma_apbx 7>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
···
 				reg = <0x8006e000 0x2000>;
 				interrupts = <59 60 58>;
 				clocks = <&clks 32>;
+				dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 

arch/arm/boot/dts/imx28-apf28dev.dts

···
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_16bit_pins_a
 						&lcdif_pins_apf28dev>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <16>;
+					bus-width = <16>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <33000033>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <96>;
+							hfront-porch = <96>;
+							vback-porch = <20>;
+							vfront-porch = <21>;
+							hsync-len = <64>;
+							vsync-len = <4>;
+							hsync-active = <1>;
+							vsync-active = <1>;
+							de-active = <1>;
+							pixelclk-active = <0>;
+						};
+					};
+				};
 			};
 		};
 

arch/arm/boot/dts/imx28-apx4devkit.dts

···
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_apx4>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <30000000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <88>;
+							hfront-porch = <40>;
+							vback-porch = <32>;
+							vfront-porch = <13>;
+							hsync-len = <48>;
+							vsync-len = <3>;
+							hsync-active = <1>;
+							vsync-active = <1>;
+							de-active = <1>;
+							pixelclk-active = <0>;
+						};
+					};
+				};
 			};
 		};
 

arch/arm/boot/dts/imx28-cfa10049.dts

···
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
-						0x1153 /* MX28_PAD_LCD_D22__GPIO_1_21 */
 						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
 						0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
···
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				w1_gpio_pins: w1-gpio@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>; /* 0 will enable the keeper */
+				};
 			};
 
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
 					     &lcdif_pins_cfa10049>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <18>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <9216000>;
+							hactive = <320>;
+							vactive = <480>;
+							hback-porch = <2>;
+							hfront-porch = <2>;
+							vback-porch = <2>;
+							vfront-porch = <2>;
+							hsync-len = <15>;
+							vsync-len = <15>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
 			};
 		};
 
···
 
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
+			};
+
+			lradc@80050000 {
+				status = "okay";
+				fsl,lradc-touchscreen-wires = <4>;
 			};
 		};
 	};
···
 		pwms = <&pwm 3 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
+
+	};
+
+	onewire@0 {
+		compatible = "w1-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&w1_gpio_pins>;
+		status = "okay";
+		gpios = <&gpio1 21 0>;
 	};
 };

arch/arm/boot/dts/imx28-evk.dts

···
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_evk>;
-				panel-enable-gpios = <&gpio3 30 0>;
+				lcd-supply = <&reg_lcd_3v3>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <33500000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <89>;
+							hfront-porch = <164>;
+							vback-porch = <23>;
+							vfront-porch = <10>;
+							hsync-len = <10>;
+							vsync-len = <10>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <0>;
+						};
+					};
+				};
 			};
 
 			can0: can@80032000 {
···
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio3 8 0>;
+			enable-active-high;
+		};
+
+		reg_lcd_3v3: lcd-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio3 30 0>;
 			enable-active-high;
 		};
 	};

arch/arm/boot/dts/imx28-m28evk.dts

···
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_m28>;
+				display = <&display>;
 				status = "okay";
+
+				display: display {
+					bits-per-pixel = <16>;
+					bus-width = <18>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <33260000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <0>;
+							hfront-porch = <256>;
+							vback-porch = <0>;
+							vfront-porch = <45>;
+							hsync-len = <1>;
+							vsync-len = <1>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
 			};
 
 			can0: can@80032000 {
···
 			phy-mode = "rmii";
 			pinctrl-names = "default";
 			pinctrl-0 = <&mac0_pins_a>;
+			clocks = <&clks 57>, <&clks 57>;
+			clock-names = "ipg", "ahb";
 			status = "okay";
 		};
 

arch/arm/boot/dts/imx28.dtsi

···
 			hsadc@80002000 {
 				reg = <0x80002000 0x2000>;
 				interrupts = <13 87>;
+				dmas = <&dma_apbh 12>;
+				dma-names = "rx";
 				status = "disabled";
 			};
 
-			dma-apbh@80004000 {
+			dma_apbh: dma-apbh@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
+				interrupts = <82 83 84 85
+					      88 88 88 88
+					      88 88 88 88
+					      87 86 0 0>;
+				interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
+						  "gpmi0", "gmpi1", "gpmi2", "gmpi3",
+						  "gpmi4", "gmpi5", "gpmi6", "gmpi7",
+						  "hsadc", "lcdif", "empty", "empty";
+				#dma-cells = <1>;
+				dma-channels = <16>;
 				clocks = <&clks 25>;
 			};
 
···
 				interrupt-names = "gpmi-dma", "bch";
 				clocks = <&clks 50>;
 				clock-names = "gpmi_io";
+				dmas = <&dma_apbh 4>;
+				dma-names = "rx-tx";
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
···
 				reg = <0x80010000 0x2000>;
 				interrupts = <96 82>;
 				clocks = <&clks 46>;
+				dmas = <&dma_apbh 0>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <0>;
 				status = "disabled";
 			};
···
 				reg = <0x80012000 0x2000>;
 				interrupts = <97 83>;
 				clocks = <&clks 47>;
+				dmas = <&dma_apbh 1>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
···
 				reg = <0x80014000 0x2000>;
 				interrupts = <98 84>;
 				clocks = <&clks 48>;
+				dmas = <&dma_apbh 2>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
···
 				reg = <0x80016000 0x2000>;
 				interrupts = <99 85>;
 				clocks = <&clks 49>;
+				dmas = <&dma_apbh 3>;
+				dma-names = "rx-tx";
 				fsl,ssp-dma-channel = <3>;
 				status = "disabled";
 			};
···
 				status = "disabled";
 			};
 
-			dma-apbx@80024000 {
+			dma_apbx: dma-apbx@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
+				interrupts = <78 79 66 0
+					      80 81 68 69
+					      70 71 72 73
+					      74 75 76 77>;
+				interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+						  "saif0", "saif1", "i2c0", "i2c1",
+						  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
+						  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+				#dma-cells = <1>;
+				dma-channels = <16>;
 				clocks = <&clks 26>;
 			};
 
···
 				reg = <0x80030000 0x2000>;
 				interrupts = <38 86>;
 				clocks = <&clks 55>;
+				dmas = <&dma_apbh 13>;
+				dma-names = "rx";
 				status = "disabled";
 			};
 
···
 				reg = <0x80042000 0x2000>;
 				interrupts = <59 80>;
 				clocks = <&clks 53>;
+				dmas = <&dma_apbx 4>;
+				dma-names = "rx-tx";
 				fsl,saif-dma-channel = <4>;
 				status = "disabled";
 			};
···
 				reg = <0x80046000 0x2000>;
 				interrupts = <58 81>;
 				clocks = <&clks 54>;
+				dmas = <&dma_apbx 5>;
+				dma-names = "rx-tx";
 				fsl,saif-dma-channel = <5>;
 				status = "disabled";
 			};
···
 			spdif@80054000 {
 				reg = <0x80054000 0x2000>;
 				interrupts = <45 66>;
+				dmas = <&dma_apbx 2>;
+				dma-names = "tx";
 				status = "disabled";
 			};
 
···
 				reg = <0x80058000 0x2000>;
 				interrupts = <111 68>;
 				clock-frequency = <100000>;
+				dmas = <&dma_apbx 6>;
+				dma-names = "rx-tx";
 				fsl,i2c-dma-channel = <6>;
 				status = "disabled";
 			};
···
 				reg = <0x8005a000 0x2000>;
 				interrupts = <110 69>;
 				clock-frequency = <100000>;
+				dmas = <&dma_apbx 7>;
+				dma-names = "rx-tx";
 				fsl,i2c-dma-channel = <7>;
 				status = "disabled";
 			};
···
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006a000 0x2000>;
 				interrupts = <112 70 71>;
+				dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+				dma-names = "rx", "tx";
 				fsl,auart-dma-channel = <8 9>;
 				clocks = <&clks 45>;
 				status = "disabled";
···
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006c000 0x2000>;
 				interrupts = <113 72 73>;
+				dmas = <&dma_apbx 10>, <&dma_apbx 11>;
+				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
 				status = "disabled";
 			};
···
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006e000 0x2000>;
 				interrupts = <114 74 75>;
+				dmas = <&dma_apbx 12>, <&dma_apbx 13>;
+				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
 				status = "disabled";
 			};
···
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80070000 0x2000>;
 				interrupts = <115 76 77>;
+				dmas = <&dma_apbx 14>, <&dma_apbx 15>;
+				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
 				status = "disabled";
 			};
···
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80072000 0x2000>;
 				interrupts = <116 78 79>;
+				dmas = <&dma_apbx 0>, <&dma_apbx 1>;
+				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
 				status = "disabled";
 			};
···
 			compatible = "fsl,imx28-fec";
 			reg = <0x800f0000 0x4000>;
 			interrupts = <101>;
-			clocks = <&clks 57>, <&clks 57>;
-			clock-names = "ipg", "ahb";
+			clocks = <&clks 57>, <&clks 57>, <&clks 64>;
+			clock-names = "ipg", "ahb", "enet_out";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/imx6qdl.dtsi

···
 		interrupt-parent = <&intc>;
 		ranges;
 
-		dma-apbh@00110000 {
+		dma_apbh: dma-apbh@00110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
+			interrupts = <0 13 0x04>, <0 13 0x04>, <0 13 0x04>, <0 13 0x04>;
+			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+			#dma-cells = <1>;
+			dma-channels = <4>;
 			clocks = <&clks 106>;
 		};
 
···
 				 <&clks 150>, <&clks 149>;
 			clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
 				      "gpmi_bch_apb", "per1_bch";
+			dmas = <&dma_apbh 0>;
+			dma-names = "rx-tx";
 			fsl,gpmi-dma-channel = <0>;
 			status = "disabled";
 		};

arch/arm/boot/dts/omap2.dtsi

···
 		};
 	};
 
+	pmu {
+		compatible = "arm,arm1136-pmu";
+		interrupts = <3>;
+	};
+
 	soc {
 		compatible = "ti,omap-infra";
 		mpu {
···
 			reg = <0x480FE000 0x1000>;
 		};
 
+		sdma: dma-controller@48056000 {
+			compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
+			reg = <0x48056000 0x1000>;
+			interrupts = <12>,
+				     <13>,
+				     <14>,
+				     <15>;
+			#dma-cells = <1>;
+			#dma-channels = <32>;
+			#dma-requests = <64>;
+		};
+
 		uart1: serial@4806a000 {
 			compatible = "ti,omap2-uart";
 			ti,hwmods = "uart1";
···
 		};
 
 		timer2: timer@4802a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x4802a000 0x400>;
 			interrupts = <38>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@48078000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48078000 0x400>;
 			interrupts = <39>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@4807a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x4807a000 0x400>;
 			interrupts = <40>;
 			ti,hwmods = "timer4";
 		};
 
 		timer5: timer@4807c000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x4807c000 0x400>;
 			interrupts = <41>;
 			ti,hwmods = "timer5";
···
 		};
 
 		timer6: timer@4807e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x4807e000 0x400>;
 			interrupts = <42>;
 			ti,hwmods = "timer6";
···
 		};
 
 		timer7: timer@48080000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48080000 0x400>;
 			interrupts = <43>;
 			ti,hwmods = "timer7";
···
 		};
 
 		timer8: timer@48082000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48082000 0x400>;
 			interrupts = <44>;
 			ti,hwmods = "timer8";
···
 		};
 
 		timer9: timer@48084000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48084000 0x400>;
 			interrupts = <45>;
 			ti,hwmods = "timer9";
···
 		};
 
 		timer10: timer@48086000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48086000 0x400>;
 			interrupts = <46>;
 			ti,hwmods = "timer10";
···
 		};
 
 		timer11: timer@48088000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48088000 0x400>;
 			interrupts = <47>;
 			ti,hwmods = "timer11";
···
 		};
 
 		timer12: timer@4808a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x4808a000 0x400>;
 			interrupts = <48>;
 			ti,hwmods = "timer12";

arch/arm/boot/dts/omap2420-h4.dts

···
 		reg = <0x80000000 0x4000000>; /* 64 MB */
 	};
 };
+
+&gpmc {
+	ranges = <0 0 0x08000000 0x04000000>;
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		linux,mtd-name= "intel,ge28f256l18b85";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0 0 0x04000000>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <160>;
+		gpmc,cs-wr-off-ns = <160>;
+		gpmc,adv-on-ns = <20>;
+		gpmc,adv-rd-off-ns = <50>;
+		gpmc,adv-wr-off-ns = <50>;
+		gpmc,oe-on-ns = <60>;
+		gpmc,oe-off-ns = <120>;
+		gpmc,we-on-ns = <60>;
+		gpmc,we-off-ns = <120>;
+		gpmc,rd-cycle-ns = <170>;
+		gpmc,wr-cycle-ns = <170>;
+		gpmc,access-ns = <150>;
+		gpmc,page-burst-access-ns = <10>;
+
+		partition@0 {
+			label = "bootloader";
+			reg = <0 0x20000>;
+		};
+		partition@0x20000 {
+			label = "params";
+			reg = <0x20000 0x20000>;
+		};
+		partition@0x40000 {
+			label = "kernel";
+			reg = <0x40000 0x200000>;
+		};
+		partition@0x240000 {
+			label = "file-system";
+			reg = <0x240000 0x3dc0000>;
+		};
+	};
+};

arch/arm/boot/dts/omap2420.dtsi

···
 			pinctrl-single,function-mask = <0x3f>;
 		};
 
+		gpio1: gpio@48018000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x48018000 0x200>;
+			interrupts = <29>;
+			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio2: gpio@4801a000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x4801a000 0x200>;
+			interrupts = <30>;
+			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio3: gpio@4801c000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x4801c000 0x200>;
+			interrupts = <31>;
+			ti,hwmods = "gpio3";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio4: gpio@4801e000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x4801e000 0x200>;
+			interrupts = <32>;
+			ti,hwmods = "gpio4";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpmc: gpmc@6800a000 {
+			compatible = "ti,omap2420-gpmc";
+			reg = <0x6800a000 0x1000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <20>;
+			gpmc,num-cs = <8>;
+			gpmc,num-waitpins = <4>;
+			ti,hwmods = "gpmc";
+		};
+
 		mcbsp1: mcbsp@48074000 {
 			compatible = "ti,omap2420-mcbsp";
 			reg = <0x48074000 0xff>;
···
 				     <60>; /* RX interrupt */
 			interrupt-names = "tx", "rx";
 			ti,hwmods = "mcbsp1";
+			dmas = <&sdma 31>,
+			       <&sdma 32>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp2: mcbsp@48076000 {
···
 				     <63>; /* RX interrupt */
 			interrupt-names = "tx", "rx";
 			ti,hwmods = "mcbsp2";
+			dmas = <&sdma 33>,
+			       <&sdma 34>;
+			dma-names = "tx", "rx";
 		};
 
 		timer1: timer@48028000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x48028000 0x400>;
 			interrupts = <37>;
 			ti,hwmods = "timer1";

arch/arm/boot/dts/omap2430.dtsi

···
 			pinctrl-single,function-mask = <0x3f>;
 		};
 
+		gpio1: gpio@4900c000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x4900c000 0x200>;
+			interrupts = <29>;
+			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio2: gpio@4900e000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x4900e000 0x200>;
+			interrupts = <30>;
+			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio3: gpio@49010000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x49010000 0x200>;
+			interrupts = <31>;
+			ti,hwmods = "gpio3";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio4: gpio@49012000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x49012000 0x200>;
+			interrupts = <32>;
+			ti,hwmods = "gpio4";
+			ti,gpio-always-on;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio5: gpio@480b6000 {
+			compatible = "ti,omap2-gpio";
+			reg = <0x480b6000 0x200>;
+			interrupts = <33>;
+			ti,hwmods = "gpio5";
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpmc: gpmc@6e000000 {
+			compatible = "ti,omap2430-gpmc";
+			reg = <0x6e000000 0x1000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <20>;
+			gpmc,num-cs = <8>;
+			gpmc,num-waitpins = <4>;
+			ti,hwmods = "gpmc";
+		};
+
 		mcbsp1: mcbsp@48074000 {
 			compatible = "ti,omap2430-mcbsp";
 			reg = <0x48074000 0xff>;
···
 			interrupt-names = "common", "tx", "rx", "rx_overflow";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp1";
+			dmas = <&sdma 31>,
+			       <&sdma 32>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp2: mcbsp@48076000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp2";
+			dmas = <&sdma 33>,
+			       <&sdma 34>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp3: mcbsp@4808c000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp3";
+			dmas = <&sdma 17>,
+			       <&sdma 18>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp4: mcbsp@4808e000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp4";
+			dmas = <&sdma 19>,
+			       <&sdma 20>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp5: mcbsp@48096000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp5";
+			dmas = <&sdma 21>,
+			       <&sdma 22>;
+			dma-names = "tx", "rx";
 		};
 
 		timer1: timer@49018000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap2420-timer";
 			reg = <0x49018000 0x400>;
 			interrupts = <37>;
 			ti,hwmods = "timer1";

arch/arm/boot/dts/omap3-beagle-xm.dts

···
 	model = "TI OMAP3 BeagleBoard xM";
 	compatible = "ti,omap3-beagle-xm, ti,omap3-beagle", "ti,omap3";
 
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
 	memory {
 		device_type = "memory";
 		reg = <0x80000000 0x20000000>; /* 512 MB */
···
 
 	leds {
 		compatible = "gpio-leds";
-		pmu_stat {
-			label = "beagleboard::pmu_stat";
-			gpios = <&twl_gpio 19 0>; /* LEDB */
-		};
 
 		heartbeat {
 			label = "beagleboard::usr0";
···
 			label = "beagleboard::usr1";
 			gpios = <&gpio5 21 0>; /* 149 -> D7 LED */
 			linux,default-trigger = "mmc0";
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		pmu_stat {
+			label = "beagleboard::pmu_stat";
+			pwms = <&twl_pwmled 1 7812500>;
+			max-brightness = <127>;
 		};
 	};
 
···
 	 * BIT(15), BIT(16), BIT(17)
 	 */
 	ti,pulldowns = <0x03a1c4>;
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap3-beagle.dts

···
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
 
 / {
 	model = "TI OMAP3 BeagleBoard";
 	compatible = "ti,omap3-beagle", "ti,omap3";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
 
 	memory {
 		device_type = "memory";

arch/arm/boot/dts/omap3-devkit8000.dts

···
+/*
+ * Author: Anil Kumar <[e-mail]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+/ {
+	model = "TimLL OMAP3 Devkit8000";
+	compatible = "timll,omap3-devkit8000", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			label = "devkit8000::led1";
+			gpios = <&gpio6 26 0>;	/* 186 -> LED1 */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		mmc {
+			label = "devkit8000::led2";
+			gpios = <&gpio6 3 0>;	/* 163 -> LED2 */
+			default-state = "on";
+			linux,default-trigger = "none";
+		};
+
+		usr {
+			label = "devkit8000::led3";
+			gpios = <&gpio6 4 0>;	/* 164 -> LED3 */
+			default-state = "on";
+			linux,default-trigger = "usr";
+                };
+
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "devkit8000";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+		ti,audio-routing =
+			"Ext Spk", "PREDRIVEL",
+			"Ext Spk", "PREDRIVER",
+			"MAINMIC", "Main Mic",
+			"Main Mic", "Mic Bias 1";
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>;	/* SYS_NIRQ cascaded to intc */
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&i2c3 {
+	status = "disabled";
+};
+
+/include/ "twl4030.dtsi"
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	vmmc_aux-supply = <&vsim>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&wdt2 {
+	status = "disabled";
+};
+
+&mcbsp1 {
+	status = "disabled";
+};
+
+&mcbsp3 {
+	status = "disabled";
+};
+
+&mcbsp4 {
+	status = "disabled";
+};
+
+&mcbsp5 {
+	status = "disabled";
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x04>;       /* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <16>;
+
+		gpmc,sync-clk = <0>;
+		gpmc,cs-on = <0>;
+		gpmc,cs-rd-off = <44>;
+		gpmc,cs-wr-off = <44>;
+		gpmc,adv-on = <6>;
+		gpmc,adv-rd-off = <34>;
+		gpmc,adv-wr-off = <44>;
+		gpmc,we-off = <40>;
+		gpmc,oe-off = <54>;
+		gpmc,access = <64>;
+		gpmc,rd-cycle = <82>;
+		gpmc,wr-cycle = <82>;
+		gpmc,wr-access = <40>;
+		gpmc,wr-data-mux-bus = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		x-loader@0 {
+			label = "X-Loader";
+			reg = <0 0x80000>;
+		};
+
+		bootloaders@80000 {
+			label = "U-Boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		bootloaders_env@260000 {
+			label = "U-Boot Env";
+			reg = <0x260000 0x20000>;
+		};
+
+		kernel@280000 {
+			label = "Kernel";
+			reg = <0x280000 0x400000>;
+		};
+
+		filesystem@680000 {
+			label = "File System";
+			reg = <0x680000 0xf980000>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-evm.dts

···
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
 
 / {
 	model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)";
 	compatible = "ti,omap3-evm", "ti,omap3";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
 
 	memory {
 		device_type = "memory";
···
 
 &twl_gpio {
 	ti,use-leds;
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap3-igep.dtsi

···
+/*
+ * Device Tree Source for IGEP Technology devices
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <[e-mail]>
+ * Copyright (C) 2012 Enric Balletbo i Serra <[e-mail]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "igep2";
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
+};
+
+&omap3_pmx_core {
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x152 0x100	/* uart1_rx.uart1_rx INPUT | MODE0 */
+			0x14c 0		/* uart1_tx.uart1_tx OUTPUT | MODE0 */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x14a 0x100	/* uart2_rx.uart2_rx INPUT | MODE0 */
+			0x148 0		/* uart2_tx.uart2_tx OUTPUT | MODE0 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e 0x100	/* uart3_rx.uart3_rx INPUT | MODE0 */
+			0x170 0		/* uart3_tx.uart3_tx OUTPUT | MODE0 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 0x0118    /* sdmmc1_clk.sdmmc1_clk INPUT PULLUP | MODE 0 */
+			0x116 0x0118    /* sdmmc1_cmd.sdmmc1_cmd INPUT PULLUP | MODE 0 */
+			0x118 0x0118 	/* sdmmc1_dat0.sdmmc1_dat0 INPUT PULLUP | MODE 0 */
+			0x11a 0x0118	/* sdmmc1_dat1.sdmmc1_dat1 INPUT PULLUP | MODE 0 */
+			0x11c 0x0118	/* sdmmc1_dat2.sdmmc1_dat2 INPUT PULLUP | MODE 0 */
+			0x11e 0x0118	/* sdmmc1_dat3.sdmmc1_dat3 INPUT PULLUP | MODE 0 */
+			0x120 0x0100	/* sdmmc1_dat4.sdmmc1_dat4 INPUT | MODE 0 */
+			0x122 0x0100	/* sdmmc1_dat5.sdmmc1_dat5 INPUT | MODE 0 */
+			0x124 0x0100	/* sdmmc1_dat6.sdmmc1_dat6 INPUT | MODE 0 */
+			0x126 0x0100	/* sdmmc1_dat7.sdmmc1_dat7 INPUT | MODE 0 */
+		>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			      };
+		};
+	};
+};
+
+/include/ "twl4030.dtsi"
+
+&i2c2 {
+	clock-frequency = <400000>;
+};
+
+&mmc1 {
+      pinctrl-names = "default";
+      pinctrl-0 = <&mmc1_pins>;
+      vmmc-supply = <&vmmc1>;
+      vmmc_aux-supply = <&vsim>;
+      bus-width = <8>;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart3_pins>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+};

arch/arm/boot/dts/omap3-igep0020.dts

···
+/*
+ * Device Tree Source for IGEPv2 board
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <[e-mail]>
+ * Copyright (C) 2012 Enric Balletbo i Serra <[e-mail]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "omap3-igep.dtsi"
+
+/ {
+	model = "IGEPv2";
+	compatible = "isee,omap3-igep0020", "ti,omap3";
+
+	leds {
+		compatible = "gpio-leds";
+		boot {
+			 label = "omap3:green:boot";
+			 gpios = <&gpio1 26 0>;
+			 default-state = "on";
+		};
+
+		user0 {
+			 label = "omap3:red:user0";
+			 gpios = <&gpio1 27 0>;
+			 default-state = "off";
+		};
+
+		user1 {
+			 label = "omap3:red:user1";
+			 gpios = <&gpio1 28 0>;
+			 default-state = "off";
+		};
+
+		user2 {
+			label = "omap3:green:user1";
+			gpios = <&twl_gpio 19 1>;
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+
+	/*
+	 * Display monitor features are burnt in the EEPROM
+	 * as EDID data.
+	 */
+	eeprom@50 {
+		compatible = "ti,eeprom";
+		reg = <0x50>;
+	};
+};

arch/arm/boot/dts/omap3-igep0030.dts

···
+/*
+ * Device Tree Source for IGEP COM Module
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <[e-mail]>
+ * Copyright (C) 2012 Enric Balletbo i Serra <[e-mail]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "omap3-igep.dtsi"
+
+/ {
+	model = "IGEP COM Module";
+	compatible = "isee,omap3-igep0030", "ti,omap3";
+
+	leds {
+		compatible = "gpio-leds";
+		boot {
+			 label = "omap3:green:boot";
+			 gpios = <&twl_gpio 13 1>;
+			 default-state = "on";
+		};
+
+		user0 {
+			 label = "omap3:red:user0";
+			 gpios = <&twl_gpio 18 1>; /* LEDA */
+			 default-state = "off";
+		};
+
+		user1 {
+			 label = "omap3:green:user1";
+			 gpios = <&twl_gpio 19 1>; /* LEDB */
+			 default-state = "off";
+		};
+
+		user2 {
+			 label = "omap3:red:user1";
+			 gpios = <&gpio1 16 1>;
+			 default-state = "off";
+		};
+	};
+};

arch/arm/boot/dts/omap3-overo.dtsi

···
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
 
 / {
-	leds {
-		compatible = "gpio-leds";
+	pwmleds {
+		compatible = "pwm-leds";
+
 		overo {
 			label = "overo:blue:COM";
-			gpios = <&twl_gpio 19 0>;
-			linux,default-trigger = "mmc0";
+			pwms = <&twl_pwmled 1 7812500>;
+			max-brightness = <127>;
 		};
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "overo";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
 	};
 };
 
···
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
 	};
 };
 
···
 
 &twl_gpio {
 	ti,use-leds;
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap3.dtsi

···
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+		ti,hwmods = "debugss";
+	};
+
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
···
 			reg = <0x48200000 0x1000>;
 		};
 
+		sdma: dma-controller@48056000 {
+			compatible = "ti,omap3630-sdma", "ti,omap3430-sdma";
+			reg = <0x48056000 0x1000>;
+			interrupts = <12>,
+				     <13>,
+				     <14>,
+				     <15>;
+			#dma-cells = <1>;
+			#dma-channels = <32>;
+			#dma-requests = <96>;
+		};
+
 		omap3_pmx_core: pinmux@48002030 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";
 			reg = <0x48002030 0x05cc>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			pinctrl-single,register-width = <16>;
-			pinctrl-single,function-mask = <0x7fff>;
+			pinctrl-single,function-mask = <0x7f1f>;
 		};
 
-		omap3_pmx_wkup: pinmux@0x48002a58 {
+		omap3_pmx_wkup: pinmux@0x48002a00 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";
-			reg = <0x48002a58 0x5c>;
+			reg = <0x48002a00 0x5c>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			pinctrl-single,register-width = <16>;
-			pinctrl-single,function-mask = <0x7fff>;
+			pinctrl-single,function-mask = <0x7f1f>;
 		};
 
 		gpio1: gpio@48310000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x48310000 0x200>;
+			interrupts = <29>;
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@49050000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x49050000 0x200>;
+			interrupts = <30>;
 			ti,hwmods = "gpio2";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio3: gpio@49052000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x49052000 0x200>;
+			interrupts = <31>;
 			ti,hwmods = "gpio3";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio4: gpio@49054000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x49054000 0x200>;
+			interrupts = <32>;
 			ti,hwmods = "gpio4";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio5: gpio@49056000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x49056000 0x200>;
+			interrupts = <33>;
 			ti,hwmods = "gpio5";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio6: gpio@49058000 {
 			compatible = "ti,omap3-gpio";
+			reg = <0x49058000 0x200>;
+			interrupts = <34>;
 			ti,hwmods = "gpio6";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		uart1: serial@4806a000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi1";
 			ti,spi-num-cs = <4>;
+			dmas = <&sdma 35>,
+			       <&sdma 36>,
+			       <&sdma 37>,
+			       <&sdma 38>,
+			       <&sdma 39>,
+			       <&sdma 40>,
+			       <&sdma 41>,
+			       <&sdma 42>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
 		};
 
 		mcspi2: spi@4809a000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi2";
 			ti,spi-num-cs = <2>;
+			dmas = <&sdma 43>,
+			       <&sdma 44>,
+			       <&sdma 45>,
+			       <&sdma 46>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 		};
 
 		mcspi3: spi@480b8000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi3";
 			ti,spi-num-cs = <2>;
+			dmas = <&sdma 15>,
+			       <&sdma 16>,
+			       <&sdma 23>,
+			       <&sdma 24>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 		};
 
 		mcspi4: spi@480ba000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi4";
 			ti,spi-num-cs = <1>;
+			dmas = <&sdma 70>, <&sdma 71>;
+			dma-names = "tx0", "rx0";
 		};
 
 		mmc1: mmc@4809c000 {
 			compatible = "ti,omap3-hsmmc";
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
+			dmas = <&sdma 61>, <&sdma 62>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc2: mmc@480b4000 {
 			compatible = "ti,omap3-hsmmc";
 			ti,hwmods = "mmc2";
+			dmas = <&sdma 47>, <&sdma 48>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc3: mmc@480ad000 {
 			compatible = "ti,omap3-hsmmc";
 			ti,hwmods = "mmc3";
+			dmas = <&sdma 77>, <&sdma 78>;
+			dma-names = "tx", "rx";
 		};
 
 		wdt2: wdt@48314000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp1";
+			dmas = <&sdma 31>,
+			       <&sdma 32>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp2: mcbsp@49022000 {
···
 			interrupt-names = "common", "tx", "rx", "sidetone";
 			ti,buffer-size = <1280>;
 			ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
+			dmas = <&sdma 33>,
+			       <&sdma 34>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp3: mcbsp@49024000 {
···
 			interrupt-names = "common", "tx", "rx", "sidetone";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
+			dmas = <&sdma 17>,
+			       <&sdma 18>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp4: mcbsp@49026000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp4";
+			dmas = <&sdma 19>,
+			       <&sdma 20>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp5: mcbsp@48096000 {
···
 			interrupt-names = "common", "tx", "rx";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp5";
+			dmas = <&sdma 21>,
+			       <&sdma 22>;
+			dma-names = "tx", "rx";
 		};
 
 		timer1: timer@48318000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48318000 0x400>;
 			interrupts = <37>;
 			ti,hwmods = "timer1";
···
 		};
 
 		timer2: timer@49032000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x49032000 0x400>;
 			interrupts = <38>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@49034000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x49034000 0x400>;
 			interrupts = <39>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@49036000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x49036000 0x400>;
 			interrupts = <40>;
 			ti,hwmods = "timer4";
 		};
 
 		timer5: timer@49038000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x49038000 0x400>;
 			interrupts = <41>;
 			ti,hwmods = "timer5";
···
 		};
 
 		timer6: timer@4903a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x4903a000 0x400>;
 			interrupts = <42>;
 			ti,hwmods = "timer6";
···
 		};
 
 		timer7: timer@4903c000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x4903c000 0x400>;
 			interrupts = <43>;
 			ti,hwmods = "timer7";
···
 		};
 
 		timer8: timer@4903e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x4903e000 0x400>;
 			interrupts = <44>;
 			ti,hwmods = "timer8";
···
 		};
 
 		timer9: timer@49040000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x49040000 0x400>;
 			interrupts = <45>;
 			ti,hwmods = "timer9";
···
 		};
 
 		timer10: timer@48086000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48086000 0x400>;
 			interrupts = <46>;
 			ti,hwmods = "timer10";
···
 		};
 
 		timer11: timer@48088000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48088000 0x400>;
 			interrupts = <47>;
 			ti,hwmods = "timer11";
···
 		};
 
 		timer12: timer@48304000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48304000 0x400>;
 			interrupts = <95>;
 			ti,hwmods = "timer12";
···
 			};
 		};
 
+		gpmc: gpmc@6e000000 {
+			compatible = "ti,omap3430-gpmc";
+			ti,hwmods = "gpmc";
+			reg = <0x6e000000 0x02d0>;
+			interrupts = <20>;
+			gpmc,num-cs = <8>;
+			gpmc,num-waitpins = <4>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+		};
+
+		usb_otg_hs: usb_otg_hs@480ab000 {
+			compatible = "ti,omap3-musb";
+			reg = <0x480ab000 0x1000>;
+			interrupts = <0 92 0x4>, <0 93 0x4>;
+			interrupt-names = "mc", "dma";
+			ti,hwmods = "usb_otg_hs";
+			usb-phy = <&usb2_phy>;
+			multipoint = <1>;
+			num-eps = <16>;
+			ram-bits = <12>;
+		};
 	};
 };

arch/arm/boot/dts/omap3430-sdp.dts

···
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+
+/ {
+	model = "TI OMAP3430 SDP";
+	compatible = "ti,omap3430-sdp", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	};
+};
+
+/include/ "twl4030.dtsi"
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	vmmc_aux-supply = <&vsim>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&gpmc {
+	ranges = <0 0 0x10000000 0x08000000>,
+		 <1 0 0x28000000 0x08000000>,
+		 <2 0 0x20000000 0x10000000>;
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		linux,mtd-name= "intel,pf48f6000m0y1be";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0 0 0x08000000>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+
+		partition@0 {
+			label = "bootloader-nor";
+			reg = <0 0x40000>;
+		};
+		partition@0x40000 {
+			label = "params-nor";
+			reg = <0x40000 0x40000>;
+		};
+		partition@0x80000 {
+			label = "kernel-nor";
+			reg = <0x80000 0x200000>;
+		};
+		partition@0x280000 {
+			label = "filesystem-nor";
+			reg = <0x240000 0x7d80000>;
+		};
+	};
+
+	nand@1,0 {
+		linux,mtd-name= "micron,mt29f1g08abb";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1 0 0x08000000>;
+		nand-bus-width = <8>;
+
+		ti,nand-ecc-opt = "sw";
+		gpmc,device-nand;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <36>;
+		gpmc,cs-wr-off-ns = <36>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <24>;
+		gpmc,adv-wr-off-ns = <36>;
+		gpmc,oe-on-ns = <6>;
+		gpmc,oe-off-ns = <48>;
+		gpmc,we-on-ns = <6>;
+		gpmc,we-off-ns = <30>;
+		gpmc,rd-cycle-ns = <72>;
+		gpmc,wr-cycle-ns = <72>;
+		gpmc,access-ns = <54>;
+		gpmc,wr-access-ns = <30>;
+
+		partition@0 {
+			label = "xloader-nand";
+			reg = <0 0x80000>;
+		};
+		partition@0x80000 {
+			label = "bootloader-nand";
+			reg = <0x80000 0x140000>;
+		};
+		partition@0x1c0000 {
+			label = "params-nand";
+			reg = <0x1c0000 0xc0000>;
+		};
+		partition@0x280000 {
+			label = "kernel-nand";
+			reg = <0x280000 0x500000>;
+		};
+		partition@0x780000 {
+			label = "filesystem-nand";
+			reg = <0x780000 0x7880000>;
+		};
+	};
+
+	onenand@2,0 {
+		linux,mtd-name= "samsung,kfm2g16q2m-deb8";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <2 0 0x10000000>;
+
+		gpmc,device-width = <2>;
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <84>;
+		gpmc,cs-wr-off-ns = <72>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <18>;
+		gpmc,adv-wr-off-ns = <18>;
+		gpmc,oe-on-ns = <30>;
+		gpmc,oe-off-ns = <84>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <42>;
+		gpmc,rd-cycle-ns = <108>;
+		gpmc,wr-cycle-ns = <96>;
+		gpmc,access-ns = <78>;
+		gpmc,wr-data-mux-bus-ns = <30>;
+
+		partition@0 {
+			label = "xloader-onenand";
+			reg = <0 0x80000>;
+		};
+		partition@0x80000 {
+			label = "bootloader-onenand";
+			reg = <0x80000 0x40000>;
+		};
+		partition@0xc0000 {
+			label = "params-onenand";
+			reg = <0xc0000 0x20000>;
+		};
+		partition@0xe0000 {
+			label = "kernel-onenand";
+			reg = <0xe0000 0x200000>;
+		};
+		partition@0x2e0000 {
+			label = "filesystem-onenand";
+			reg = <0x2e0000 0xfd20000>;
+		};
+	};
+};

arch/arm/boot/dts/omap34xx.dtsi

···
+/*
+ * Device Tree Source for OMAP34xx/OMAP35xx SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap3.dtsi"
+
+/ {
+	cpus {
+		cpu@0 {
+			/* OMAP343x/OMAP35xx variants OPP1-5 */
+			operating-points = <
+				/* kHz    uV */
+				125000   975000
+				250000  1075000
+				500000  1200000
+				550000  1270000
+				600000  1350000
+			>;
+			clock-latency = <300000>; /* From legacy driver */
+		};
+	};
+};

arch/arm/boot/dts/omap36xx.dtsi

···
 		serial3 = &uart4;
 	};
 
+	cpus {
+		/* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */
+		cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				300000   975000
+				600000  1075000
+				800000  1200000
+			>;
+			clock-latency = <300000>; /* From legacy driver */
+		};
+	};
+
 	ocp {
 		uart4: serial@49042000 {
 			compatible = "ti,omap3-uart";

arch/arm/boot/dts/omap4-panda-a4.dts

···
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-/include/ "omap4-panda.dts"
+/dts-v1/;
+
+/include/ "omap443x.dtsi"
+/include/ "omap4-panda-common.dtsi"
 
 /* Pandaboard Rev A4+ have external pullups on SCL & SDA */
 &dss_hdmi_pins {

arch/arm/boot/dts/omap4-panda-common.dtsi

···
+/*
+ * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/include/ "elpida_ecb240abacn.dtsi"
+
+/ {
+	model = "TI OMAP4 PandaBoard";
+	compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat {
+			label = "pandaboard::status1";
+			gpios = <&gpio1 7 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		mmc {
+			label = "pandaboard::status2";
+			gpios = <&gpio1 8 0>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	sound: sound {
+		compatible = "ti,abe-twl6040";
+		ti,model = "PandaBoard";
+
+		ti,mclk-freq = <38400000>;
+
+		ti,mcpdm = <&mcpdm>;
+
+		ti,twl6040 = <&twl6040>;
+
+		/* Audio routing */
+		ti,audio-routing =
+			"Headset Stereophone", "HSOL",
+			"Headset Stereophone", "HSOR",
+			"Ext Spk", "HFL",
+			"Ext Spk", "HFR",
+			"Line Out", "AUXL",
+			"Line Out", "AUXR",
+			"HSMIC", "Headset Mic",
+			"Headset Mic", "Headset Mic Bias",
+			"AFML", "Line In",
+			"AFMR", "Line In";
+	};
+};
+
+&omap4_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6040_pins
+			&mcpdm_pins
+			&mcbsp1_pins
+			&dss_hdmi_pins
+			&tpd12s015_pins
+	>;
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0xe0 0x3	/* hdq_sio.gpio_127 OUTPUT | MODE3 */
+			0x160 0x100	/* sys_nirq2.sys_nirq2 INPUT | MODE0 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0xc6 0x108	/* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
+			0xc8 0x108	/* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
+			0xca 0x118	/* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
+			0xcc 0x108	/* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
+			0xce 0x108	/* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0xbe 0x100	/* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
+			0xc0 0x108	/* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
+			0xc2 0x8		/* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
+			0xc4 0x100	/* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
+		>;
+	};
+
+	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+		pinctrl-single,pins = <
+			0x5a 0x118	/* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */
+			0x5c 0x118	/* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */
+			0x5e 0x118	/* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */
+		>;
+	};
+
+	tpd12s015_pins: pinmux_tpd12s015_pins {
+		pinctrl-single,pins = <
+			0x22 0x3	/* gpmc_a17.gpio_41 OUTPUT | MODE3 */
+			0x48 0x3	/* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */
+			0x58 0x10b	/* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0xe2 0x118        /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+			0xe4 0x118        /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0xe6 0x118        /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
+			0xe8 0x118        /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0xea 0x118        /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
+			0xec 0x118     /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			0xee 0x118        /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
+			0xf0 0x118     /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		/* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+		interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
+		interrupt-parent = <&gic>;
+	};
+
+	twl6040: twl@4b {
+		compatible = "ti,twl6040";
+		reg = <0x4b>;
+		/* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
+		interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
+		interrupt-parent = <&gic>;
+		ti,audpwron-gpio = <&gpio4 31 0>;  /* gpio line 127 */
+
+		vio-supply = <&v1v8>;
+		v2v1-supply = <&v2v1>;
+		enable-active-high;
+	};
+};
+
+/include/ "twl6030.dtsi"
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	clock-frequency = <100000>;
+
+	/*
+	 * Display monitor features are burnt in their EEPROM as EDID data.
+	 * The EEPROM is connected as I2C slave device.
+	 */
+	eeprom@50 {
+		compatible = "ti,eeprom";
+		reg = <0x50>;
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	clock-frequency = <400000>;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&mmc4 {
+	status = "disabled";
+};
+
+&mmc5 {
+	ti,non-removable;
+	bus-width = <4>;
+};
+
+&emif1 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};
+
+&emif2 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};
+
+&mcbsp2 {
+	status = "disabled";
+};
+
+&mcbsp3 {
+	status = "disabled";
+};
+
+&dmic {
+	status = "disabled";
+};
+
+&twl_usb_comparator {
+	usb-supply = <&vusb>;
+};
+
+&usb_otg_hs {
+	interface-type = <1>;
+	mode = <3>;
+	power = <50>;
+};

arch/arm/boot/dts/omap4-panda-es.dts

···
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-/include/ "omap4-panda.dts"
+/dts-v1/;
+
+/include/ "omap4460.dtsi"
+/include/ "omap4-panda-common.dtsi"
 
 /* Audio routing is differnet between PandaBoard4430 and PandaBoardES */
 &sound {

arch/arm/boot/dts/omap4-panda.dts

···
  */
 /dts-v1/;
 
-/include/ "omap4.dtsi"
-/include/ "elpida_ecb240abacn.dtsi"
-
-/ {
-	model = "TI OMAP4 PandaBoard";
-	compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
-
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		heartbeat {
-			label = "pandaboard::status1";
-			gpios = <&gpio1 7 0>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		mmc {
-			label = "pandaboard::status2";
-			gpios = <&gpio1 8 0>;
-			linux,default-trigger = "mmc0";
-		};
-	};
-
-	sound: sound {
-		compatible = "ti,abe-twl6040";
-		ti,model = "PandaBoard";
-
-		ti,mclk-freq = <38400000>;
-
-		ti,mcpdm = <&mcpdm>;
-
-		ti,twl6040 = <&twl6040>;
-
-		/* Audio routing */
-		ti,audio-routing =
-			"Headset Stereophone", "HSOL",
-			"Headset Stereophone", "HSOR",
-			"Ext Spk", "HFL",
-			"Ext Spk", "HFR",
-			"Line Out", "AUXL",
-			"Line Out", "AUXR",
-			"HSMIC", "Headset Mic",
-			"Headset Mic", "Headset Mic Bias",
-			"AFML", "Line In",
-			"AFMR", "Line In";
-	};
-};
-
-&omap4_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&twl6040_pins
-			&mcpdm_pins
-			&mcbsp1_pins
-			&dss_hdmi_pins
-			&tpd12s015_pins
-	>;
-
-	twl6040_pins: pinmux_twl6040_pins {
-		pinctrl-single,pins = <
-			0xe0 0x3	/* hdq_sio.gpio_127 OUTPUT | MODE3 */
-			0x160 0x100	/* sys_nirq2.sys_nirq2 INPUT | MODE0 */
-		>;
-	};
-
-	mcpdm_pins: pinmux_mcpdm_pins {
-		pinctrl-single,pins = <
-			0xc6 0x108	/* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
-			0xc8 0x108	/* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
-			0xca 0x118	/* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
-			0xcc 0x108	/* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
-			0xce 0x108	/* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
-		>;
-	};
-
-	mcbsp1_pins: pinmux_mcbsp1_pins {
-		pinctrl-single,pins = <
-			0xbe 0x100	/* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
-			0xc0 0x108	/* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
-			0xc2 0x8		/* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
-			0xc4 0x100	/* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
-		>;
-	};
-
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-			0x5a 0x118	/* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */
-			0x5c 0x118	/* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */
-			0x5e 0x118	/* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			0x22 0x3	/* gpmc_a17.gpio_41 OUTPUT | MODE3 */
-			0x48 0x3	/* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */
-			0x58 0x10b	/* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
-		>;
-	};
-};
-
-&i2c1 {
-	clock-frequency = <400000>;
-
-	twl: twl@48 {
-		reg = <0x48>;
-		/* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
-		interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
-		interrupt-parent = <&gic>;
-	};
-
-	twl6040: twl@4b {
-		compatible = "ti,twl6040";
-		reg = <0x4b>;
-		/* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
-		interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
-		interrupt-parent = <&gic>;
-		ti,audpwron-gpio = <&gpio4 31 0>;  /* gpio line 127 */
-
-		vio-supply = <&v1v8>;
-		v2v1-supply = <&v2v1>;
-		enable-active-high;
-	};
-};
-
-/include/ "twl6030.dtsi"
-
-&i2c2 {
-	clock-frequency = <400000>;
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-
-	/*
-	 * Display monitor features are burnt in their EEPROM as EDID data.
-	 * The EEPROM is connected as I2C slave device.
-	 */
-	eeprom@50 {
-		compatible = "ti,eeprom";
-		reg = <0x50>;
-	};
-};
-
-&i2c4 {
-	clock-frequency = <400000>;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmc>;
-	bus-width = <8>;
-};
-
-&mmc2 {
-	status = "disabled";
-};
-
-&mmc3 {
-	status = "disabled";
-};
-
-&mmc4 {
-	status = "disabled";
-};
-
-&mmc5 {
-	ti,non-removable;
-	bus-width = <4>;
-};
-
-&emif1 {
-	cs1-used;
-	device-handle = <&elpida_ECB240ABACN>;
-};
-
-&emif2 {
-	cs1-used;
-	device-handle = <&elpida_ECB240ABACN>;
-};
-
-&mcbsp2 {
-	status = "disabled";
-};
-
-&mcbsp3 {
-	status = "disabled";
-};
-
-&dmic {
-	status = "disabled";
-};
-
-&twl_usb_comparator {
-	usb-supply = <&vusb>;
-};
+/include/ "omap443x.dtsi"
+/include/ "omap4-panda-common.dtsi"

arch/arm/boot/dts/omap4-sdp.dts

···
  */
 /dts-v1/;
 
-/include/ "omap4.dtsi"
+/include/ "omap443x.dtsi"
 /include/ "elpida_ecb240abacn.dtsi"
 
 / {
···
 			label = "omap4:green:user";
 			gpios = <&gpio5 11 0>; /* 139 */
 		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+		kpad {
+			label = "omap4::keypad";
+			pwms = <&twl_pwm 0 7812500>;
+			max-brightness = <127>;
+		};
+
+		charging {
+			label = "omap4:green:chrg";
+			pwms = <&twl_pwmled 0 7812500>;
+			max-brightness = <255>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&twl_pwm 1 7812500>;
+		brightness-levels = <
+				0 10 20 30 40
+				50 60 70 80 90
+				100 110 120 127
+				>;
+		default-brightness-level = <13>;
 	};
 
 	sound {
···
 			0x58 0x10b	/* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
 		>;
 	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0xe2 0x118        /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+			0xe4 0x118       /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+                        0xe6 0x118        /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
+                        0xe8 0x118        /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0xea 0x118        /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
+			0xec 0x118     /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			0xee 0x118        /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
+			0xf0 0x118     /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
+		>;
+	};
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
 	clock-frequency = <400000>;
 
 	twl: twl@48 {
···
 /include/ "twl6030.dtsi"
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
 	clock-frequency = <400000>;
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
 	clock-frequency = <400000>;
 
 	/*
···
 };
 
 &i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
 	clock-frequency = <400000>;
 
 	/*
···
 
 &twl_usb_comparator {
 	usb-supply = <&vusb>;
+};
+
+&usb_otg_hs {
+	interface-type = <1>;
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap4-var-som.dts

···
  */
 /dts-v1/;
 
-/include/ "omap4.dtsi"
+/include/ "omap443x.dtsi"
 
 / {
 	model = "Variscite OMAP4 SOM";

arch/arm/boot/dts/omap4.dtsi

···
 		#size-cells = <1>;
 		ranges;
 		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+		reg = <0x44000000 0x1000>,
+		      <0x44800000 0x2000>,
+		      <0x45000000 0x1000>;
+		interrupts = <0 9 0x4>,
+			     <0 10 0x4>;
 
 		counter32k: counter@4a304000 {
 			compatible = "ti,omap-counter32k";
···
 			pinctrl-single,function-mask = <0x7fff>;
 		};
 
+		sdma: dma-controller@4a056000 {
+			compatible = "ti,omap4430-sdma";
+			reg = <0x4a056000 0x1000>;
+			interrupts = <0 12 0x4>,
+				     <0 13 0x4>,
+				     <0 14 0x4>,
+				     <0 15 0x4>;
+			#dma-cells = <1>;
+			#dma-channels = <32>;
+			#dma-requests = <127>;
+		};
+
 		gpio1: gpio@4a310000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x4a310000 0x200>;
 			interrupts = <0 29 0x4>;
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@48055000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio3: gpio@48057000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio4: gpio@48059000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio5: gpio@4805b000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio6: gpio@4805d000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,omap4430-gpmc";
+			reg = <0x50000000 0x1000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <0 20 0x4>;
+			gpmc,num-cs = <8>;
+			gpmc,num-waitpins = <4>;
+			ti,hwmods = "gpmc";
 		};
 
 		uart1: serial@4806a000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi1";
 			ti,spi-num-cs = <4>;
+			dmas = <&sdma 35>,
+			       <&sdma 36>,
+			       <&sdma 37>,
+			       <&sdma 38>,
+			       <&sdma 39>,
+			       <&sdma 40>,
+			       <&sdma 41>,
+			       <&sdma 42>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
 		};
 
 		mcspi2: spi@4809a000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi2";
 			ti,spi-num-cs = <2>;
+			dmas = <&sdma 43>,
+			       <&sdma 44>,
+			       <&sdma 45>,
+			       <&sdma 46>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 		};
 
 		mcspi3: spi@480b8000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi3";
 			ti,spi-num-cs = <2>;
+			dmas = <&sdma 15>, <&sdma 16>;
+			dma-names = "tx0", "rx0";
 		};
 
 		mcspi4: spi@480ba000 {
···
 			#size-cells = <0>;
 			ti,hwmods = "mcspi4";
 			ti,spi-num-cs = <1>;
+			dmas = <&sdma 70>, <&sdma 71>;
+			dma-names = "tx0", "rx0";
 		};
 
 		mmc1: mmc@4809c000 {
···
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
 			ti,needs-special-reset;
+			dmas = <&sdma 61>, <&sdma 62>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc2: mmc@480b4000 {
···
 			interrupts = <0 86 0x4>;
 			ti,hwmods = "mmc2";
 			ti,needs-special-reset;
+			dmas = <&sdma 47>, <&sdma 48>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc3: mmc@480ad000 {
···
 			interrupts = <0 94 0x4>;
 			ti,hwmods = "mmc3";
 			ti,needs-special-reset;
+			dmas = <&sdma 77>, <&sdma 78>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc4: mmc@480d1000 {
···
 			interrupts = <0 96 0x4>;
 			ti,hwmods = "mmc4";
 			ti,needs-special-reset;
+			dmas = <&sdma 57>, <&sdma 58>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc5: mmc@480d5000 {
···
 			interrupts = <0 59 0x4>;
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
+			dmas = <&sdma 59>, <&sdma 60>;
+			dma-names = "tx", "rx";
 		};
 
 		wdt2: wdt@4a314000 {
···
 			reg-names = "mpu", "dma";
 			interrupts = <0 112 0x4>;
 			ti,hwmods = "mcpdm";
+			dmas = <&sdma 65>,
+			       <&sdma 66>;
+			dma-names = "up_link", "dn_link";
 		};
 
 		dmic: dmic@4012e000 {
···
 			reg-names = "mpu", "dma";
 			interrupts = <0 114 0x4>;
 			ti,hwmods = "dmic";
+			dmas = <&sdma 67>;
+			dma-names = "up_link";
 		};
 
 		mcbsp1: mcbsp@40122000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp1";
+			dmas = <&sdma 33>,
+			       <&sdma 34>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp2: mcbsp@40124000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp2";
+			dmas = <&sdma 17>,
+			       <&sdma 18>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp3: mcbsp@40126000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp3";
+			dmas = <&sdma 19>,
+			       <&sdma 20>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp4: mcbsp@48096000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp4";
+			dmas = <&sdma 31>,
+			       <&sdma 32>;
+			dma-names = "tx", "rx";
 		};
 
 		keypad: keypad@4a31c000 {
···
 			#size-cells = <1>;
 			ranges;
 			ti,hwmods = "ocp2scp_usb_phy";
+			usb2_phy: usb2phy@4a0ad080 {
+				compatible = "ti,omap-usb2";
+				reg = <0x4a0ad080 0x58>;
+				ctrl-module = <&omap_control_usb>;
+			};
 		};
 
 		timer1: timer@4a318000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x4a318000 0x80>;
 			interrupts = <0 37 0x4>;
 			ti,hwmods = "timer1";
···
 		};
 
 		timer2: timer@48032000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48032000 0x80>;
 			interrupts = <0 38 0x4>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@48034000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x48034000 0x80>;
 			interrupts = <0 39 0x4>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@48036000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x48036000 0x80>;
 			interrupts = <0 40 0x4>;
 			ti,hwmods = "timer4";
 		};
 
 		timer5: timer@40138000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x40138000 0x80>,
 			      <0x49038000 0x80>;
 			interrupts = <0 41 0x4>;
···
 		};
 
 		timer6: timer@4013a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x4013a000 0x80>,
 			      <0x4903a000 0x80>;
 			interrupts = <0 42 0x4>;
···
 		};
 
 		timer7: timer@4013c000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x4013c000 0x80>,
 			      <0x4903c000 0x80>;
 			interrupts = <0 43 0x4>;
···
 		};
 
 		timer8: timer@4013e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x4013e000 0x80>,
 			      <0x4903e000 0x80>;
 			interrupts = <0 44 0x4>;
···
 		};
 
 		timer9: timer@4803e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x4803e000 0x80>;
 			interrupts = <0 45 0x4>;
 			ti,hwmods = "timer9";
···
 		};
 
 		timer10: timer@48086000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap3430-timer";
 			reg = <0x48086000 0x80>;
 			interrupts = <0 46 0x4>;
 			ti,hwmods = "timer10";
···
 		};
 
 		timer11: timer@48088000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap4430-timer";
 			reg = <0x48088000 0x80>;
 			interrupts = <0 47 0x4>;
 			ti,hwmods = "timer11";
···
 				interrupt-parent = <&gic>;
 				interrupts = <0 77 0x4>;
 			};
+		};
+
+		omap_control_usb: omap-control-usb@4a002300 {
+			compatible = "ti,omap-control-usb";
+			reg = <0x4a002300 0x4>,
+			      <0x4a00233c 0x4>;
+			reg-names = "control_dev_conf", "otghs_control";
+			ti,type = <1>;
+		};
+
+		usb_otg_hs: usb_otg_hs@4a0ab000 {
+			compatible = "ti,omap4-musb";
+			reg = <0x4a0ab000 0x7ff>;
+			interrupts = <0 92 0x4>, <0 93 0x4>;
+			interrupt-names = "mc", "dma";
+			ti,hwmods = "usb_otg_hs";
+			usb-phy = <&usb2_phy>;
+			multipoint = <1>;
+			num-eps = <16>;
+			ram-bits = <12>;
+			ti,has-mailbox;
 		};
 	};
 };

arch/arm/boot/dts/omap443x.dtsi

···
+/*
+ * Device Tree Source for OMAP443x SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap4.dtsi"
+
+/ {
+	cpus {
+		cpu@0 {
+			/* OMAP443x variants OPP50-OPPNT */
+			operating-points = <
+				/* kHz    uV */
+				300000  1025000
+				600000  1200000
+				800000  1313000
+				1008000 1375000
+			>;
+			clock-latency = <300000>; /* From legacy driver */
+		};
+	};
+};

arch/arm/boot/dts/omap4460.dtsi

···
+/*
+ * Device Tree Source for OMAP4460 SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+/include/ "omap4.dtsi"
+
+/ {
+	cpus {
+		/* OMAP446x 'standard device' variants OPP50 to OPPTurbo */
+		cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				350000   975000
+				700000  1075000
+				920000  1200000
+			>;
+			clock-latency = <300000>; /* From legacy driver */
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <0 54 0x4>,
+			     <0 55 0x4>;
+		ti,hwmods = "debugss";
+	};
+};

arch/arm/boot/dts/omap5-evm.dts

···
 
 	memory {
 		device_type = "memory";
-		reg = <0x80000000 0x80000000>; /* 2 GB */
+		reg = <0x80000000 0x7F000000>; /* 2032 MB */
 	};
 
 	vmmcsd_fixed: fixedregulator-mmcsd {
···
 			0x15a 0x100	/* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */
 		>;
 	};
+
+        i2c1_pins: pinmux_i2c1_pins {
+                pinctrl-single,pins = <
+                        0x1b2 0x118        /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+                        0x1b4 0x118        /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+                >;
+        };
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x178 0x100        /* i2c2_scl INPUTENABLE | MODE0 */
+			0x17a 0x100        /* i2c2_sda INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x13a 0x100        /* i2c3_scl INPUTENABLE | MODE0 */
+			0x13c 0x100     /* i2c3_sda INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			0xb8 0x100        /* i2c4_scl INPUTENABLE | MODE0 */
+			0xba 0x100     /* i2c4_sda INPUTENABLE | MODE0 */
+		>;
+	};
+
+	i2c5_pins: pinmux_i2c5_pins {
+		pinctrl-single,pins = <
+			0x184 0x100        /* i2c5_scl INPUTENABLE | MODE0 */
+			0x186 0x100     /* i2c5_sda INPUTENABLE | MODE0 */
+		>;
+	};
+
+	mcspi2_pins: pinmux_mcspi2_pins {
+		pinctrl-single,pins = <
+			0xbc 0x100	/*  MCSPI2_CLK INPUTENABLE | MODE0 */
+			0xbe 0x100	/*  MCSPI2_SIMO INPUTENABLE | MODE0 */
+			0xc0 0x118	/*  MCSPI2_SOMI PULLUP | INPUTENABLE | MODE0*/
+			0xc2 0x0	/*  MCSPI2_CS MODE0*/
+		>;
+	};
+
+	mcspi3_pins: pinmux_mcspi3_pins {
+		pinctrl-single,pins = <
+			0x78 0x101	/*  MCSPI2_SOMI INPUTENABLE | MODE1 */
+			0x7a 0x101	/*  MCSPI2_CS INPUTENABLE | MODE1 */
+			0x7c 0x101	/*  MCSPI2_SIMO INPUTENABLE | MODE1 */
+			0x7e 0x101	/*  MCSPI2_CLK INPUTENABLE | MODE1 */
+		>;
+	};
+
+	mcspi4_pins: pinmux_mcspi4_pins {
+		pinctrl-single,pins = <
+			0x164 0x101	/*  MCSPI2_CLK INPUTENABLE | MODE1 */
+			0x168 0x101	/*  MCSPI2_SIMO INPUTENABLE | MODE1 */
+			0x16a 0x101	/*  MCSPI2_SOMI INPUTENABLE | MODE1 */
+			0x16c 0x101	/*  MCSPI2_CS INPUTENABLE | MODE1 */
+		>;
+	};
 };
 
 &mmc1 {
···
 	status = "disabled";
 };
 
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+};
+
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
 	clock-frequency = <400000>;
 
 	/* Pressure Sensor */
···
 	};
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	clock-frequency = <400000>;
+};
+
 &i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
 	clock-frequency = <400000>;
 
 	/* Temperature Sensor */
···
 		compatible = "ti,tmp102";
 		reg = <0x48>;
 	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+
+	clock-frequency = <400000>;
 };
 
 &keypad {
···
 &emif2 {
 	cs1-used;
 	device-handle = <&samsung_K3PE0E000B>;
+};
+
+&mcspi1 {
+
+};
+
+&mcspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi2_pins>;
+};
+
+&mcspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi3_pins>;
+};
+
+&mcspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi4_pins>;
 };

arch/arm/boot/dts/omap5.dtsi

···
 /include/ "skeleton.dtsi"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	compatible = "ti,omap5";
 	interrupt-parent = <&gic>;
 
···
 	cpus {
 		cpu@0 {
 			compatible = "arm,cortex-a15";
-			timer {
-				compatible = "arm,armv7-timer";
-				/* 14th PPI IRQ, active low level-sensitive */
-				interrupts = <1 14 0x308>;
-				clock-frequency = <6144000>;
-			};
 		};
 		cpu@1 {
 			compatible = "arm,cortex-a15";
-			timer {
-				compatible = "arm,armv7-timer";
-				/* 14th PPI IRQ, active low level-sensitive */
-				interrupts = <1 14 0x308>;
-				clock-frequency = <6144000>;
-			};
 		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		/* PPI secure/nonsecure IRQ, active low level-sensitive */
+		interrupts = <1 13 0x308>,
+			     <1 14 0x308>,
+			     <1 11 0x308>,
+			     <1 10 0x308>;
+		clock-frequency = <6144000>;
+	};
+
+	gic: interrupt-controller@48211000 {
+		compatible = "arm,cortex-a15-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48211000 0x1000>,
+		      <0x48212000 0x1000>,
+		      <0x48214000 0x2000>,
+		      <0x48216000 0x2000>;
 	};
 
 	/*
···
 		#size-cells = <1>;
 		ranges;
 		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+		reg = <0x44000000 0x2000>,
+		      <0x44800000 0x3000>,
+		      <0x45000000 0x4000>;
+		interrupts = <0 9 0x4>,
+			     <0 10 0x4>;
 
 		counter32k: counter@4ae04000 {
 			compatible = "ti,omap-counter32k";
···
 			pinctrl-single,function-mask = <0x7fff>;
 		};
 
-		gic: interrupt-controller@48211000 {
-			compatible = "arm,cortex-a15-gic";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x48211000 0x1000>,
-			      <0x48212000 0x1000>;
+		sdma: dma-controller@4a056000 {
+			compatible = "ti,omap4430-sdma";
+			reg = <0x4a056000 0x1000>;
+			interrupts = <0 12 0x4>,
+				     <0 13 0x4>,
+				     <0 14 0x4>,
+				     <0 15 0x4>;
+			#dma-cells = <1>;
+			#dma-channels = <32>;
+			#dma-requests = <127>;
 		};
 
 		gpio1: gpio@4ae10000 {
···
 			reg = <0x4ae10000 0x200>;
 			interrupts = <0 29 0x4>;
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@48055000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio3: gpio@48057000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio4: gpio@48059000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio5: gpio@4805b000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio6: gpio@4805d000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio7: gpio@48051000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio8: gpio@48053000 {
···
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,omap4430-gpmc";
+			reg = <0x50000000 0x1000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <0 20 0x4>;
+			gpmc,num-cs = <8>;
+			gpmc,num-waitpins = <4>;
+			ti,hwmods = "gpmc";
 		};
 
 		i2c1: i2c@48070000 {
···
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c5";
+		};
+
+		mcspi1: spi@48098000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x48098000 0x200>;
+			interrupts = <0 65 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi1";
+			ti,spi-num-cs = <4>;
+			dmas = <&sdma 35>,
+			       <&sdma 36>,
+			       <&sdma 37>,
+			       <&sdma 38>,
+			       <&sdma 39>,
+			       <&sdma 40>,
+			       <&sdma 41>,
+			       <&sdma 42>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
+		};
+
+		mcspi2: spi@4809a000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x4809a000 0x200>;
+			interrupts = <0 66 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi2";
+			ti,spi-num-cs = <2>;
+			dmas = <&sdma 43>,
+			       <&sdma 44>,
+			       <&sdma 45>,
+			       <&sdma 46>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
+		};
+
+		mcspi3: spi@480b8000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x480b8000 0x200>;
+			interrupts = <0 91 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi3";
+			ti,spi-num-cs = <2>;
+			dmas = <&sdma 15>, <&sdma 16>;
+			dma-names = "tx0", "rx0";
+		};
+
+		mcspi4: spi@480ba000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x480ba000 0x200>;
+			interrupts = <0 48 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi4";
+			ti,spi-num-cs = <1>;
+			dmas = <&sdma 70>, <&sdma 71>;
+			dma-names = "tx0", "rx0";
 		};
 
 		uart1: serial@4806a000 {
···
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
 			ti,needs-special-reset;
+			dmas = <&sdma 61>, <&sdma 62>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc2: mmc@480b4000 {
···
 			interrupts = <0 86 0x4>;
 			ti,hwmods = "mmc2";
 			ti,needs-special-reset;
+			dmas = <&sdma 47>, <&sdma 48>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc3: mmc@480ad000 {
···
 			interrupts = <0 94 0x4>;
 			ti,hwmods = "mmc3";
 			ti,needs-special-reset;
+			dmas = <&sdma 77>, <&sdma 78>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc4: mmc@480d1000 {
···
 			interrupts = <0 96 0x4>;
 			ti,hwmods = "mmc4";
 			ti,needs-special-reset;
+			dmas = <&sdma 57>, <&sdma 58>;
+			dma-names = "tx", "rx";
 		};
 
 		mmc5: mmc@480d5000 {
···
 			interrupts = <0 59 0x4>;
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
+			dmas = <&sdma 59>, <&sdma 60>;
+			dma-names = "tx", "rx";
 		};
 
 		keypad: keypad@4ae1c000 {
 			compatible = "ti,omap4-keypad";
+			reg = <0x4ae1c000 0x400>;
 			ti,hwmods = "kbd";
 		};
 
···
 			reg-names = "mpu", "dma";
 			interrupts = <0 112 0x4>;
 			ti,hwmods = "mcpdm";
+			dmas = <&sdma 65>,
+			       <&sdma 66>;
+			dma-names = "up_link", "dn_link";
 		};
 
 		dmic: dmic@4012e000 {
···
 			reg-names = "mpu", "dma";
 			interrupts = <0 114 0x4>;
 			ti,hwmods = "dmic";
+			dmas = <&sdma 67>;
+			dma-names = "up_link";
 		};
 
 		mcbsp1: mcbsp@40122000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp1";
+			dmas = <&sdma 33>,
+			       <&sdma 34>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp2: mcbsp@40124000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp2";
+			dmas = <&sdma 17>,
+			       <&sdma 18>;
+			dma-names = "tx", "rx";
 		};
 
 		mcbsp3: mcbsp@40126000 {
···
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp3";
+			dmas = <&sdma 19>,
+			       <&sdma 20>;
+			dma-names = "tx", "rx";
 		};
 
 		timer1: timer@4ae18000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x4ae18000 0x80>;
 			interrupts = <0 37 0x4>;
 			ti,hwmods = "timer1";
···
 		};
 
 		timer2: timer@48032000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x48032000 0x80>;
 			interrupts = <0 38 0x4>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@48034000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x48034000 0x80>;
 			interrupts = <0 39 0x4>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@48036000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x48036000 0x80>;
 			interrupts = <0 40 0x4>;
 			ti,hwmods = "timer4";
 		};
 
 		timer5: timer@40138000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x40138000 0x80>,
 			      <0x49038000 0x80>;
 			interrupts = <0 41 0x4>;
···
 		};
 
 		timer6: timer@4013a000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x4013a000 0x80>,
 			      <0x4903a000 0x80>;
 			interrupts = <0 42 0x4>;
···
 		};
 
 		timer7: timer@4013c000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x4013c000 0x80>,
 			      <0x4903c000 0x80>;
 			interrupts = <0 43 0x4>;
···
 		};
 
 		timer8: timer@4013e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x4013e000 0x80>,
 			      <0x4903e000 0x80>;
 			interrupts = <0 44 0x4>;
···
 		};
 
 		timer9: timer@4803e000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x4803e000 0x80>;
 			interrupts = <0 45 0x4>;
 			ti,hwmods = "timer9";
 		};
 
 		timer10: timer@48086000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x48086000 0x80>;
 			interrupts = <0 46 0x4>;
 			ti,hwmods = "timer10";
 		};
 
 		timer11: timer@48088000 {
-			compatible = "ti,omap2-timer";
+			compatible = "ti,omap5430-timer";
 			reg = <0x48088000 0x80>;
 			interrupts = <0 47 0x4>;
 			ti,hwmods = "timer11";
 			ti,timer-pwm;
+		};
+
+		wdt2: wdt@4ae14000 {
+			compatible = "ti,omap5-wdt", "ti,omap3-wdt";
+			reg = <0x4ae14000 0x80>;
+			interrupts = <0 80 0x4>;
+			ti,hwmods = "wd_timer2";
 		};
 
 		emif1: emif@0x4c000000 {
···
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
 			hw-caps-temp-alert;
+		};
+
+		omap_control_usb: omap-control-usb@4a002300 {
+			compatible = "ti,omap-control-usb";
+			reg = <0x4a002300 0x4>,
+			      <0x4a002370 0x4>;
+			reg-names = "control_dev_conf", "phy_power_usb";
+			ti,type = <2>;
+		};
+
+		omap_dwc3@4a020000 {
+			compatible = "ti,dwc3";
+			ti,hwmods = "usb_otg_ss";
+			reg = <0x4a020000 0x1000>;
+			interrupts = <0 93 4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			utmi-mode = <2>;
+			ranges;
+			dwc3@4a030000 {
+				compatible = "synopsys,dwc3";
+				reg = <0x4a030000 0x1000>;
+				interrupts = <0 92 4>;
+				usb-phy = <&usb2_phy>, <&usb3_phy>;
+				tx-fifo-resize;
+			};
+		};
+
+		ocp2scp {
+			compatible = "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp1";
+			usb2_phy: usb2phy@4a084000 {
+				compatible = "ti,omap-usb2";
+				reg = <0x4a084000 0x7c>;
+				ctrl-module = <&omap_control_usb>;
+			};
+
+			usb3_phy: usb3phy@4a084400 {
+				compatible = "ti,omap-usb3";
+				reg = <0x4a084400 0x80>,
+				      <0x4a084800 0x64>,
+				      <0x4a084c00 0x40>;
+				reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+				ctrl-module = <&omap_control_usb>;
+			};
 		};
 	};
 };

arch/arm/boot/dts/tegra114-dalmore.dts

···
 		reg = <0x80000000 0x40000000>;
 	};
 
+	pinmux {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			dap1_dout_pn2 {
+				nvidia,pins = "dap1_dout_pn2",
+						"dap1_fs_pn0",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			dap2_din_pa4 {
+				nvidia,pins = "dap2_din_pa4";
+				nvidia,function = "i2s1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			dap2_dout_pa5 {
+				nvidia,pins = "dap2_dout_pa5",
+						"dap2_fs_pa2",
+						"dap2_sclk_pa3";
+				nvidia,function = "i2s1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			dap4_din_pp5 {
+				nvidia,pins = "dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_fs_pp4",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			dvfs_pwm_px0 {
+				nvidia,pins = "dvfs_pwm_px0",
+						"dvfs_clk_px2";
+				nvidia,function = "cldvfs";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_data0_po1",
+						"ulpi_data1_po2",
+						"ulpi_data2_po3",
+						"ulpi_data3_po4",
+						"ulpi_data4_po5",
+						"ulpi_data5_po6",
+						"ulpi_data6_po7",
+						"ulpi_data7_po0";
+				nvidia,function = "ulpi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			ulpi_dir_py1 {
+				nvidia,pins = "ulpi_dir_py1",
+						"ulpi_nxt_py2";
+				nvidia,function = "ulpi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "ulpi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <0>;
+			};
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0",
+						"pbb0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+				nvidia,lock = <0>;
+			};
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <0>;
+			};
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7";
+				nvidia,function = "uartd";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a18_pb1";
+				nvidia,function = "uartd";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_a19_pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "uartd";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_ad5_pg5 {
+				nvidia,pins = "gmi_ad5_pg5",
+						"gmi_cs6_n_pi3",
+						"gmi_wr_n_pi0";
+				nvidia,function = "spi4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_ad6_pg6 {
+				nvidia,pins = "gmi_ad6_pg6",
+						"gmi_ad7_pg7";
+				nvidia,function = "spi4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_cs1_n_pj2 {
+				nvidia,pins = "gmi_cs1_n_pj2",
+						"gmi_oe_n_pi1";
+				nvidia,function = "soc";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			sdmmc1_cmd_pz1 {
+				nvidia,pins = "sdmmc1_cmd_pz1",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat3_py4";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			sdmmc1_wp_n_pv3 {
+				nvidia,pins = "sdmmc1_wp_n_pv3";
+				nvidia,function = "spi4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4",
+						"kb_col4_pq4",
+						"sdmmc3_clk_lb_out_pee4",
+						"sdmmc3_clk_lb_in_pee5";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0",
+						"kb_col1_pq1",
+						"kb_col2_pq2",
+						"kb_row0_pr0",
+						"kb_row1_pr1",
+						"kb_row2_pr2";
+				nvidia,function = "kbc";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1",
+						"dap3_sclk_pp3";
+				nvidia,function = "displayb";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <0>;
+			};
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <0>;
+			};
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			kb_row10_ps2 {
+				nvidia,pins = "kb_row10_ps2";
+				nvidia,function = "uarta";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			kb_row9_ps1 {
+				nvidia,pins = "kb_row9_ps1";
+				nvidia,function = "uarta";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <0>;
+			};
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			core_pwr_req {
+				nvidia,pins = "core_pwr_req";
+				nvidia,function = "pwron";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			cpu_pwr_req {
+				nvidia,pins = "cpu_pwr_req";
+				nvidia,function = "cpu";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pwr_int_n {
+				nvidia,pins = "pwr_int_n";
+				nvidia,function = "pmi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			reset_out_n {
+				nvidia,pins = "reset_out_n";
+				nvidia,function = "reset_out_n";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <0>;
+			};
+			uart2_cts_n_pj5 {
+				nvidia,pins = "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			uart2_rts_n_pj6 {
+				nvidia,pins = "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3";
+				nvidia,function = "irda";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2";
+				nvidia,function = "irda";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <0>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <0>;
+			};
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,rcv-sel = <1>;
+			};
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "usb";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+			};
+			usb_vbus_en0_pn4 {
+				nvidia,pins = "usb_vbus_en0_pn4";
+				nvidia,function = "usb";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+				nvidia,lock = <0>;
+				nvidia,open-drain = <1>;
+			};
+			gpio_x6_aud_px6 {
+				nvidia,pins = "gpio_x6_aud_px6";
+				nvidia,function = "spi6";
+				nvidia,pull = <2>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <1>;
+			};
+			gpio_x4_aud_px4 {
+				nvidia,pins = "gpio_x4_aud_px4",
+						"gpio_x7_aud_px7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gpio_x5_aud_px5 {
+				nvidia,pins = "gpio_x5_aud_px5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gpio_w2_aud_pw2 {
+				nvidia,pins = "gpio_w2_aud_pw2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gpio_w3_aud_pw3 {
+				nvidia,pins = "gpio_w3_aud_pw3";
+				nvidia,function = "spi6";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gpio_x1_aud_px1 {
+				nvidia,pins = "gpio_x1_aud_px1";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gpio_x3_aud_px3 {
+				nvidia,pins = "gpio_x3_aud_px3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0";
+				nvidia,function = "i2s2";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			dap3_dout_pp2 {
+				nvidia,pins = "dap3_dout_pp2";
+				nvidia,function = "i2s2";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pv1 {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			pbb3 {
+				nvidia,pins = "pbb3",
+						"pbb5",
+						"pbb6",
+						"pbb7";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pcc1 {
+				nvidia,pins = "pcc1",
+						"pcc2";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1";
+				nvidia,function = "gmi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+						"gmi_ad11_ph3",
+						"gmi_ad13_ph5",
+						"gmi_ad8_ph0",
+						"gmi_clk_pk1";
+				nvidia,function = "gmi";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			gmi_ad2_pg2 {
+				nvidia,pins = "gmi_ad2_pg2",
+						"gmi_ad3_pg3";
+				nvidia,function = "gmi";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_adv_n_pk0 {
+				nvidia,pins = "gmi_adv_n_pk0",
+						"gmi_cs0_n_pj0",
+						"gmi_cs2_n_pk3",
+						"gmi_cs4_n_pk2",
+						"gmi_cs7_n_pi6",
+						"gmi_dqs_p_pj3",
+						"gmi_iordy_pi5",
+						"gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			gmi_cs3_n_pk4 {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "gmi";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			kb_col3_pq3 {
+				nvidia,pins = "kb_col3_pq3",
+						"kb_col6_pq6",
+						"kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			kb_col5_pq5 {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3",
+						"kb_row4_pr4",
+						"kb_row6_pr6",
+						"kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "displayb";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <0>;
+			};
+			pu5 {
+				nvidia,pins = "pu5",
+						"pu6";
+				nvidia,function = "displayb";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <1>;
+				nvidia,tristate = <0>;
+				nvidia,enable-input = <1>;
+			};
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2",
+						"usb_vbus_en1_pn5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <1>;
+				nvidia,tristate = <1>;
+				nvidia,enable-input = <0>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1";
+				nvidia,high-speed-mode = <1>;
+				nvidia,schmitt = <0>;
+				nvidia,low-power-mode = <3>;
+				nvidia,pull-down-strength = <36>;
+				nvidia,pull-up-strength = <20>;
+				nvidia,slew-rate-rising = <2>;
+				nvidia,slew-rate-falling = <2>;
+			};
+			drive_sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <1>;
+				nvidia,schmitt = <0>;
+				nvidia,low-power-mode = <3>;
+				nvidia,pull-down-strength = <22>;
+				nvidia,pull-up-strength = <36>;
+				nvidia,slew-rate-rising = <0>;
+				nvidia,slew-rate-falling = <0>;
+			};
+			drive_gma {
+				nvidia,pins = "drive_gma";
+				nvidia,high-speed-mode = <1>;
+				nvidia,schmitt = <0>;
+				nvidia,low-power-mode = <3>;
+				nvidia,pull-down-strength = <2>;
+				nvidia,pull-up-strength = <1>;
+				nvidia,slew-rate-rising = <0>;
+				nvidia,slew-rate-falling = <0>;
+				nvidia,drive-type = <1>;
+			};
+		};
+	};
+
 	serial@70006300 {
 		status = "okay";
 	};
 
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		battery: smart-battery {
+			compatible = "ti,bq20z45", "sbs,sbs-battery";
+			reg = <0xb>;
+			battery-name = "battery";
+			sbs,i2c-retry-count = <2>;
+			sbs,poll-retry-count = <100>;
+		};
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		tps51632 {
+			compatible = "ti,tps51632";
+			reg = <0x43>;
+			regulator-name = "vdd-cpu";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1520000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		tps65090 {
+			compatible = "ti,tps65090";
+			reg = <0x48>;
+			interrupt-parent = <&gpio>;
+			interrupts = <72 0x04>; /* gpio PJ0 */
+
+			vsys1-supply = <&vdd_ac_bat_reg>;
+			vsys2-supply = <&vdd_ac_bat_reg>;
+			vsys3-supply = <&vdd_ac_bat_reg>;
+			infet1-supply = <&vdd_ac_bat_reg>;
+			infet2-supply = <&vdd_ac_bat_reg>;
+			infet3-supply = <&tps65090_dcdc2_reg>;
+			infet4-supply = <&tps65090_dcdc2_reg>;
+			infet5-supply = <&tps65090_dcdc2_reg>;
+			infet6-supply = <&tps65090_dcdc2_reg>;
+			infet7-supply = <&tps65090_dcdc2_reg>;
+			vsys-l1-supply = <&vdd_ac_bat_reg>;
+			vsys-l2-supply = <&vdd_ac_bat_reg>;
+
+			regulators {
+				tps65090_dcdc1_reg: dcdc1 {
+					regulator-name = "vdd-sys-5v0";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				tps65090_dcdc2_reg: dcdc2 {
+					regulator-name = "vdd-sys-3v3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				dcdc3 {
+					regulator-name = "vdd-ao";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				fet1 {
+					regulator-name = "vdd-lcd-bl";
+				};
+
+				fet3 {
+					regulator-name = "vdd-modem-3v3";
+				};
+
+				fet4 {
+					regulator-name = "avdd-lcd";
+				};
+
+				fet5 {
+					regulator-name = "vdd-lvds";
+				};
+
+				fet6 {
+					regulator-name = "vdd-sd-slot";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				fet7 {
+					regulator-name = "vdd-com-3v3";
+				};
+
+				ldo1 {
+					regulator-name = "vdd-sby-5v0";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo2 {
+					regulator-name = "vdd-sby-3v3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+
 	pmc {
 		nvidia,invert-interrupt;
+	};
+
+	sdhci@78000400 {
+		cd-gpios = <&gpio 170 1>; /* gpio PV2 */
+		bus-width = <4>;
+		status = "okay";
+	};
+
+	sdhci@78000600 {
+		bus-width = <8>;
+		status = "okay";
+		non-removable;
 	};
 
 	clocks {
···
 			reg=<0>;
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd_ac_bat_reg: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "vdd_ac_bat";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+
+		dvdd_ts_reg: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "dvdd_ts";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			enable-active-high;
+			gpio = <&gpio 61 0>; /* GPIO PH5 */
+		};
+
+		lcd_bl_en_reg: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "lcd_bl_en";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 58 0>; /* GPIO PH2 */
+		};
+
+		usb1_vbus_reg: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 108 0>; /* GPIO PN4 */
+			gpio-open-drain;
+			vin-supply = <&tps65090_dcdc1_reg>;
+		};
+
+		usb3_vbus_reg: regulator@4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "usb2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 86 0>; /* GPIO PK6 */
+			gpio-open-drain;
+			vin-supply = <&tps65090_dcdc1_reg>;
+		};
+
+		vdd_hdmi_reg: regulator@5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "vdd_hdmi_5v0";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 81 0>; /* GPIO PK1 */
+			vin-supply = <&tps65090_dcdc1_reg>;
 		};
 	};
 };

arch/arm/boot/dts/tegra114.dtsi

···
 	compatible = "nvidia,tegra114";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uarta;
+		serial1 = &uartb;
+		serial2 = &uartc;
+		serial3 = &uartd;
+	};
+
 	gic: interrupt-controller {
 		compatible = "arm,cortex-a15-gic";
 		#interrupt-cells = <3>;
···
 		compatible = "nvidia,tegra114-car";
 		reg = <0x60006000 0x1000>;
 		#clock-cells = <1>;
+	};
+
+	apbdma: dma {
+		compatible = "nvidia,tegra114-apbdma";
+		reg = <0x6000a000 0x1400>;
+		interrupts = <0 104 0x04
+			      0 105 0x04
+			      0 106 0x04
+			      0 107 0x04
+			      0 108 0x04
+			      0 109 0x04
+			      0 110 0x04
+			      0 111 0x04
+			      0 112 0x04
+			      0 113 0x04
+			      0 114 0x04
+			      0 115 0x04
+			      0 116 0x04
+			      0 117 0x04
+			      0 118 0x04
+			      0 119 0x04
+			      0 128 0x04
+			      0 129 0x04
+			      0 130 0x04
+			      0 131 0x04
+			      0 132 0x04
+			      0 133 0x04
+			      0 134 0x04
+			      0 135 0x04
+			      0 136 0x04
+			      0 137 0x04
+			      0 138 0x04
+			      0 139 0x04
+			      0 140 0x04
+			      0 141 0x04
+			      0 142 0x04
+			      0 143 0x04>;
+		clocks = <&tegra_car 34>;
 	};
 
 	ahb: ahb {
···
 		       0x70003000 0x40c>;	/* Mux registers */
 	};
 
-	serial@70006000 {
+	/*
+	 * There are two serial driver i.e. 8250 based simple serial
+	 * driver and APB DMA based serial driver for higher baudrate
+	 * and performace. To enable the 8250 based driver, the compatible
+	 * is "nvidia,tegra114-uart", "nvidia,tegra20-uart" and to enable
+	 * the APB DMA based serial driver, the comptible is
+	 * "nvidia,tegra114-hsuart", "nvidia,tegra30-hsuart".
+	 */
+	uarta: serial@70006000 {
 		compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
 		reg = <0x70006000 0x40>;
 		reg-shift = <2>;
 		interrupts = <0 36 0x04>;
+		nvidia,dma-request-selector = <&apbdma 8>;
 		status = "disabled";
 		clocks = <&tegra_car 6>;
 	};
 
-	serial@70006040 {
+	uartb: serial@70006040 {
 		compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
 		reg = <0x70006040 0x40>;
 		reg-shift = <2>;
 		interrupts = <0 37 0x04>;
+		nvidia,dma-request-selector = <&apbdma 9>;
 		status = "disabled";
 		clocks = <&tegra_car 192>;
 	};
 
-	serial@70006200 {
+	uartc: serial@70006200 {
 		compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
 		reg = <0x70006200 0x100>;
 		reg-shift = <2>;
 		interrupts = <0 46 0x04>;
+		nvidia,dma-request-selector = <&apbdma 10>;
 		status = "disabled";
 		clocks = <&tegra_car 55>;
 	};
 
-	serial@70006300 {
+	uartd: serial@70006300 {
 		compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
 		reg = <0x70006300 0x100>;
 		reg-shift = <2>;
 		interrupts = <0 90 0x04>;
+		nvidia,dma-request-selector = <&apbdma 19>;
 		status = "disabled";
 		clocks = <&tegra_car 65>;
+	};
+
+	pwm: pwm {
+		compatible = "nvidia,tegra114-pwm", "nvidia,tegra20-pwm";
+		reg = <0x7000a000 0x100>;
+		#pwm-cells = <2>;
+		clocks = <&tegra_car 17>;
+		status = "disabled";
+	};
+
+	i2c@7000c000 {
+		compatible = "nvidia,tegra114-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 12>;
+		clock-names = "div-clk";
+		status = "disabled";
+	};
+
+	i2c@7000c400 {
+		compatible = "nvidia,tegra114-i2c";
+		reg = <0x7000c400 0x100>;
+		interrupts = <0 84 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 54>;
+		clock-names = "div-clk";
+		status = "disabled";
+	};
+
+	i2c@7000c500 {
+		compatible = "nvidia,tegra114-i2c";
+		reg = <0x7000c500 0x100>;
+		interrupts = <0 92 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 67>;
+		clock-names = "div-clk";
+		status = "disabled";
+	};
+
+	i2c@7000c700 {
+		compatible = "nvidia,tegra114-i2c";
+		reg = <0x7000c700 0x100>;
+		interrupts = <0 120 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 103>;
+		clock-names = "div-clk";
+		status = "disabled";
+	};
+
+	i2c@7000d000 {
+		compatible = "nvidia,tegra114-i2c";
+		reg = <0x7000d000 0x100>;
+		interrupts = <0 53 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 47>;
+		clock-names = "div-clk";
+		status = "disabled";
+	};
+
+	spi@7000d400 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000d400 0x200>;
+		interrupts = <0 59 0x04>;
+		nvidia,dma-request-selector = <&apbdma 15>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 41>;
+		clock-names = "spi";
+		status = "disabled";
+	};
+
+	spi@7000d600 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000d600 0x200>;
+		interrupts = <0 82 0x04>;
+		nvidia,dma-request-selector = <&apbdma 16>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 44>;
+		clock-names = "spi";
+		status = "disabled";
+	};
+
+	spi@7000d800 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000d800 0x200>;
+		interrupts = <0 83 0x04>;
+		nvidia,dma-request-selector = <&apbdma 17>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 46>;
+		clock-names = "spi";
+		status = "disabled";
+	};
+
+	spi@7000da00 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000da00 0x200>;
+		interrupts = <0 93 0x04>;
+		nvidia,dma-request-selector = <&apbdma 18>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 68>;
+		clock-names = "spi";
+		status = "disabled";
+	};
+
+	spi@7000dc00 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000dc00 0x200>;
+		interrupts = <0 94 0x04>;
+		nvidia,dma-request-selector = <&apbdma 27>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 104>;
+		clock-names = "spi";
+		status = "disabled";
+	};
+
+	spi@7000de00 {
+		compatible = "nvidia,tegra114-spi";
+		reg = <0x7000de00 0x200>;
+		interrupts = <0 79 0x04>;
+		nvidia,dma-request-selector = <&apbdma 28>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 105>;
+		clock-names = "spi";
+		status = "disabled";
 	};
 
 	rtc {
···
 		reg = <0x7000e000 0x100>;
 		interrupts = <0 2 0x04>;
 		clocks = <&tegra_car 4>;
+	};
+
+	kbc {
+		compatible = "nvidia,tegra114-kbc";
+		reg = <0x7000e200 0x100>;
+		interrupts = <0 85 0x04>;
+		clocks = <&tegra_car 36>;
+		status = "disabled";
 	};
 
 	pmc {
···
 		dma-window = <0 0x40000000>;
 		nvidia,swgroups = <0x18659fe>;
 		nvidia,ahb = <&ahb>;
+	};
+
+	sdhci@78000000 {
+		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+		reg = <0x78000000 0x200>;
+		interrupts = <0 14 0x04>;
+		clocks = <&tegra_car 14>;
+		status = "disable";
+	};
+
+	sdhci@78000200 {
+		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+		reg = <0x78000200 0x200>;
+		interrupts = <0 15 0x04>;
+		clocks = <&tegra_car 9>;
+		status = "disable";
+	};
+
+	sdhci@78000400 {
+		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+		reg = <0x78000400 0x200>;
+		interrupts = <0 19 0x04>;
+		clocks = <&tegra_car 69>;
+		status = "disable";
+	};
+
+	sdhci@78000600 {
+		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+		reg = <0x78000600 0x200>;
+		interrupts = <0 31 0x04>;
+		clocks = <&tegra_car 15>;
+		status = "disable";
 	};
 
 	cpus {

arch/arm/boot/dts/tegra20-colibri-512.dtsi

···
 		};
 	};
 
+	pmc {
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <5000>;
+		nvidia,cpu-pwr-off-time = <5000>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <3875>;
+		nvidia,sys-clock-req-active-high;
+	};
+
 	memory-controller@7000f400 {
 		emc-table@83250 {
 			reg = <83250>;
···
 			"Mic", "MIC1";
 
 		nvidia,ac97-controller = <&ac97>;
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
 	regulators {

arch/arm/boot/dts/tegra20-harmony.dts

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <5000>;
+		nvidia,cpu-pwr-off-time = <5000>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <3875>;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	usb@c5000000 {
···
 			reg=<0>;
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "Power";
+			gpios = <&gpio 170 1>; /* gpio PV2, active low */
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
 		};
 	};
 
···
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
 		nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
 		nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-medcom-wide.dts

···
 	model = "Avionic Design Medcom-Wide board";
 	compatible = "ad,medcom-wide", "ad,tamonten", "nvidia,tegra20";
 
+	pwm {
+		status = "okay";
+	};
+
 	i2c@7000c000 {
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
···
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-paz00.dts

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <0>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	usb@c5000000 {
···
 	sdhci@c8000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {
···
 		nvidia,audio-codec = <&alc5632>;
 		nvidia,i2s-controller = <&tegra_i2s1>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-plutux.dts

···
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-seaboard.dts

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <5000>;
+		nvidia,cpu-pwr-off-time = <5000>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <3875>;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	memory-controller@7000f400 {
···
 		status = "okay";
 		power-gpios = <&gpio 86 0>; /* gpio PK6 */
 		bus-width = <4>;
+		keep-power-in-suspend;
 	};
 
 	sdhci@c8000400 {
···
 	sdhci@c8000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {
···
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-tamonten.dtsi

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <5000>;
+		nvidia,cpu-pwr-off-time = <5000>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <3875>;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	usb@c5008000 {

arch/arm/boot/dts/tegra20-tec.dts

···
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-trimslice.dts

···
 		};
 	};
 
+	pmc {
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <5000>;
+		nvidia,cpu-pwr-off-time = <5000>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <3875>;
+		nvidia,sys-clock-req-active-high;
+	};
+
 	usb@c5000000 {
 		status = "okay";
 		nvidia,vbus-gpio = <&gpio 170 0>; /* gpio PV2 */
···
 		};
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "Power";
+			gpios = <&gpio 190 1>; /* gpio PX6, active low */
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
+		};
+	};
+
 	poweroff {
 		compatible = "gpio-poweroff";
 		gpios = <&gpio 191 1>; /* gpio PX7, active low */
···
 		compatible = "nvidia,tegra-audio-trimslice";
 		nvidia,i2s-controller = <&tegra_i2s1>;
 		nvidia,audio-codec = <&codec>;
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-ventana.dts

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <100>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <458>;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	usb@c5000000 {
···
 		status = "okay";
 		power-gpios = <&gpio 86 0>; /* gpio PK6 */
 		bus-width = <4>;
+		keep-power-in-suspend;
 	};
 
 	sdhci@c8000400 {
···
 	sdhci@c8000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {
···
 			reg=<0>;
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "Power";
+			gpios = <&gpio 170 1>; /* gpio PV2, active low */
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
 		};
 	};
 
···
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
 		nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
 		nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20-whistler.dts

···
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <1000>;
+		nvidia,core-pwr-good-time = <0 3845>;
+		nvidia,core-pwr-off-time = <93727>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		nvidia,combined-power-req;
 	};
 
 	usb@c5000000 {
···
 	sdhci@c8000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {
···
 		nvidia,repeat-delay-ms = <160>;
 		nvidia,kbc-row-pins = <0 1 2>;
 		nvidia,kbc-col-pins = <16 17>;
+		nvidia,wakeup-source;
 		linux,keymap = <0x00000074	/* KEY_POWER */
 				0x01000066	/* KEY_HOME */
 				0x0101009E	/* KEY_BACK */
···
 
 		nvidia,i2s-controller = <&tegra_i2s1>;
 		nvidia,audio-codec = <&codec>;
+
+		clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra20.dtsi

···
 		compatible = "nvidia,tegra20-das";
 		reg = <0x70000c00 0x80>;
 	};
-	
+
 	tegra_ac97: ac97 {
 		compatible = "nvidia,tegra20-ac97";
 		reg = <0x70002000 0x200>;
···
 		reg = <0x7000a000 0x100>;
 		#pwm-cells = <2>;
 		clocks = <&tegra_car 17>;
+		status = "disabled";
 	};
 
 	rtc {
···
 		#size-cells = <0>;
 	};
 
-	phy1: usb-phy@c5000400 {
-		compatible = "nvidia,tegra20-usb-phy";
-		reg = <0xc5000400 0x3c00>;
-		phy_type = "utmi";
-		nvidia,has-legacy-mode;
-		clocks = <&tegra_car 22>, <&tegra_car 127>;
-		clock-names = "phy", "pll_u";
-	};
-
-	phy2: usb-phy@c5004400 {
-		compatible = "nvidia,tegra20-usb-phy";
-		reg = <0xc5004400 0x3c00>;
-		phy_type = "ulpi";
-		clocks = <&tegra_car 94>, <&tegra_car 127>;
-		clock-names = "phy", "pll_u";
-	};
-
-	phy3: usb-phy@c5008400 {
-		compatible = "nvidia,tegra20-usb-phy";
-		reg = <0xc5008400 0x3C00>;
-		phy_type = "utmi";
-		clocks = <&tegra_car 22>, <&tegra_car 127>;
-		clock-names = "phy", "pll_u";
-	};
-
 	usb@c5000000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5000000 0x4000>;
···
 		status = "disabled";
 	};
 
+	phy1: usb-phy@c5000400 {
+		compatible = "nvidia,tegra20-usb-phy";
+		reg = <0xc5000400 0x3c00>;
+		phy_type = "utmi";
+		nvidia,has-legacy-mode;
+		clocks = <&tegra_car 22>, <&tegra_car 127>;
+		clock-names = "phy", "pll_u";
+	};
+
 	usb@c5004000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5004000 0x4000>;
···
 		status = "disabled";
 	};
 
+	phy2: usb-phy@c5004400 {
+		compatible = "nvidia,tegra20-usb-phy";
+		reg = <0xc5004400 0x3c00>;
+		phy_type = "ulpi";
+		clocks = <&tegra_car 93>, <&tegra_car 127>;
+		clock-names = "phy", "pll_u";
+	};
+
 	usb@c5008000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5008000 0x4000>;
···
 		clocks = <&tegra_car 59>;
 		nvidia,phy = <&phy3>;
 		status = "disabled";
+	};
+
+	phy3: usb-phy@c5008400 {
+		compatible = "nvidia,tegra20-usb-phy";
+		reg = <0xc5008400 0x3c00>;
+		phy_type = "utmi";
+		clocks = <&tegra_car 22>, <&tegra_car 127>;
+		clock-names = "phy", "pll_u";
 	};
 
 	sdhci@c8000000 {

arch/arm/boot/dts/tegra30-beaver.dts

···
 	pmc {
 		status = "okay";
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	sdhci@78000000 {
···
 	sdhci@78000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {

arch/arm/boot/dts/tegra30-cardhu-a02.dts

···
 		status = "okay";
 		power-gpios = <&gpio 28 0>; /* gpio PD4 */
 		bus-width = <4>;
+		keep-power-in-suspend;
 	};
 };
 

arch/arm/boot/dts/tegra30-cardhu-a04.dts

···
 		status = "okay";
 		power-gpios = <&gpio 27 0>; /* gpio PD3 */
 		bus-width = <4>;
+		keep-power-in-suspend;
 	};
 };

arch/arm/boot/dts/tegra30-cardhu.dtsi

···
 	pmc {
 		status = "okay";
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	sdhci@78000000 {
···
 	sdhci@78000600 {
 		status = "okay";
 		bus-width = <8>;
+		non-removable;
 	};
 
 	clocks {
···
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+		clocks = <&tegra_car 184>, <&tegra_car 185>, <&tegra_car 120>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };

arch/arm/boot/dts/tegra30.dtsi

···
 		reg = <0x7000a000 0x100>;
 		#pwm-cells = <2>;
 		clocks = <&tegra_car 17>;
+		status = "disabled";
 	};
 
 	rtc {

arch/arm/boot/dts/twl4030.dtsi

···
 		compatible = "ti,twl4030-wdt";
 	};
 
+	vcc: regulator-vdd1 {
+		compatible = "ti,twl4030-vdd1";
+		regulator-min-microvolt = <600000>;
+		regulator-max-microvolt = <1450000>;
+	};
+
 	vdac: regulator-vdac {
 		compatible = "ti,twl4030-vdac";
 		regulator-min-microvolt = <1800000>;
···
 		#interrupt-cells = <1>;
 	};
 
-	twl4030-usb {
+	usb2_phy: twl4030-usb {
 		compatible = "ti,twl4030-usb";
 		interrupts = <10>, <4>;
 		usb1v5-supply = <&vusb1v5>;
 		usb1v8-supply = <&vusb1v8>;
 		usb3v1-supply = <&vusb3v1>;
 		usb_mode = <1>;
+	};
+
+	twl_pwm: pwm {
+		compatible = "ti,twl4030-pwm";
+		#pwm-cells = <2>;
+	};
+
+	twl_pwmled: pwmled {
+		compatible = "ti,twl4030-pwmled";
+		#pwm-cells = <2>;
 	};
 };

arch/arm/boot/dts/twl6030.dtsi

···
 		compatible = "ti,twl6030-usb";
 		interrupts = <4>, <10>;
 	};
+
+	twl_pwm: pwm {
+		/* provides two PWMs (id 0, 1 for PWM1 and PWM2) */
+		compatible = "ti,twl6030-pwm";
+		#pwm-cells = <2>;
+	};
+
+	twl_pwmled: pwmled {
+		/* provides one PWM (id 0 for Charging indicator LED) */
+		compatible = "ti,twl6030-pwmled";
+		#pwm-cells = <2>;
+	};
 };

arch/arm/mach-davinci/da8xx-dt.c

···
 	OF_DEV_AUXDATA("ti,davinci-i2c", 0x01c22000, "i2c_davinci.1", NULL),
 	OF_DEV_AUXDATA("ti,davinci-wdt", 0x01c21000, "watchdog", NULL),
 	OF_DEV_AUXDATA("ti,da830-mmc", 0x01c40000, "da830-mmc.0", NULL),
+	OF_DEV_AUXDATA("ti,da850-ehrpwm", 0x01f00000, "ehrpwm", NULL),
+	OF_DEV_AUXDATA("ti,da850-ehrpwm", 0x01f02000, "ehrpwm", NULL),
+	OF_DEV_AUXDATA("ti,da850-ecap", 0x01f06000, "ecap", NULL),
+	OF_DEV_AUXDATA("ti,da850-ecap", 0x01f07000, "ecap", NULL),
+	OF_DEV_AUXDATA("ti,da850-ecap", 0x01f08000, "ecap", NULL),
+	OF_DEV_AUXDATA("ti,da830-spi", 0x01f0e000, "spi_davinci.1", NULL),
 	{}
 };
 

arch/arm/mach-exynos/common.c

···
 	},
 };
 
-#ifdef CONFIG_ARCH_EXYNOS5
-static struct map_desc exynos5440_iodesc[] __initdata = {
-	{
-		.virtual	= (unsigned long)S5P_VA_CHIPID,
-		.pfn		= __phys_to_pfn(EXYNOS5440_PA_CHIPID),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE,
-	},
-};
-#endif
-
 static struct map_desc exynos4_iodesc[] __initdata = {
 	{
 		.virtual	= (unsigned long)S3C_VA_SYS,
···
 	exynos_pm_late_initcall();
 }
 
+#ifdef CONFIG_OF
+int __init exynos_fdt_map_chipid(unsigned long node, const char *uname,
+					int depth, void *data)
+{
+	struct map_desc iodesc;
+	__be32 *reg;
+	unsigned long len;
+
+	if (!of_flat_dt_is_compatible(node, "samsung,exynos4210-chipid") &&
+		!of_flat_dt_is_compatible(node, "samsung,exynos5440-clock"))
+		return 0;
+
+	reg = of_get_flat_dt_prop(node, "reg", &len);
+	if (reg == NULL || len != (sizeof(unsigned long) * 2))
+		return 0;
+
+	iodesc.pfn = __phys_to_pfn(be32_to_cpu(reg[0]));
+	iodesc.length = be32_to_cpu(reg[1]) - 1;
+	iodesc.virtual = (unsigned long)S5P_VA_CHIPID;
+	iodesc.type = MT_DEVICE;
+	iotable_init(&iodesc, 1);
+	return 1;
+}
+#endif
+
 /*
  * exynos_map_io
  *
···
 
 void __init exynos_init_io(struct map_desc *mach_desc, int size)
 {
-	struct map_desc *iodesc = exynos_iodesc;
-	int iodesc_sz = ARRAY_SIZE(exynos_iodesc);
-#if defined(CONFIG_OF) && defined(CONFIG_ARCH_EXYNOS5)
-	unsigned long root = of_get_flat_dt_root();
-
-	/* initialize the io descriptors we need for initialization */
-	if (of_flat_dt_is_compatible(root, "samsung,exynos5440")) {
-		iodesc = exynos5440_iodesc;
-		iodesc_sz = ARRAY_SIZE(exynos5440_iodesc);
-	}
+#ifdef CONFIG_OF
+	if (initial_boot_params)
+		of_scan_flat_dt(exynos_fdt_map_chipid, NULL);
+	else
 #endif
-
-	iotable_init(iodesc, iodesc_sz);
+		iotable_init(exynos_iodesc, ARRAY_SIZE(exynos_iodesc));
 
 	if (mach_desc)
 		iotable_init(mach_desc, size);

arch/arm/mach-exynos/include/mach/map.h

···
 #define EXYNOS4_PA_ONENAND_DMA		0x0C600000
 
 #define EXYNOS_PA_CHIPID		0x10000000
-#define EXYNOS5440_PA_CHIPID		0x00160000
 
 #define EXYNOS4_PA_SYSCON		0x10010000
 #define EXYNOS5_PA_SYSCON		0x10050100

arch/arm/mach-mxs/mach-mxs.c

···
 #include <linux/irqchip.h>
 #include <linux/irqchip/mxs.h>
 #include <linux/micrel_phy.h>
-#include <linux/mxsfb.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/phy.h>
···
 	__raw_writel(mask, reg + MXS_TOG_ADDR);
 }
 
-static struct fb_videomode mx23evk_video_modes[] = {
-	{
-		.name		= "Samsung-LMS430HF02",
-		.refresh	= 60,
-		.xres		= 480,
-		.yres		= 272,
-		.pixclock	= 108096, /* picosecond (9.2 MHz) */
-		.left_margin	= 15,
-		.right_margin	= 8,
-		.upper_margin	= 12,
-		.lower_margin	= 4,
-		.hsync_len	= 1,
-		.vsync_len	= 1,
-	},
-};
-
-static struct fb_videomode mx28evk_video_modes[] = {
-	{
-		.name		= "Seiko-43WVF1G",
-		.refresh	= 60,
-		.xres		= 800,
-		.yres		= 480,
-		.pixclock	= 29851, /* picosecond (33.5 MHz) */
-		.left_margin	= 89,
-		.right_margin	= 164,
-		.upper_margin	= 23,
-		.lower_margin	= 10,
-		.hsync_len	= 10,
-		.vsync_len	= 10,
-	},
-};
-
-static struct fb_videomode m28evk_video_modes[] = {
-	{
-		.name		= "Ampire AM-800480R2TMQW-T01H",
-		.refresh	= 60,
-		.xres		= 800,
-		.yres		= 480,
-		.pixclock	= 30066, /* picosecond (33.26 MHz) */
-		.left_margin	= 0,
-		.right_margin	= 256,
-		.upper_margin	= 0,
-		.lower_margin	= 45,
-		.hsync_len	= 1,
-		.vsync_len	= 1,
-	},
-};
-
-static struct fb_videomode apx4devkit_video_modes[] = {
-	{
-		.name		= "HannStar PJ70112A",
-		.refresh	= 60,
-		.xres		= 800,
-		.yres		= 480,
-		.pixclock	= 33333, /* picosecond (30.00 MHz) */
-		.left_margin	= 88,
-		.right_margin	= 40,
-		.upper_margin	= 32,
-		.lower_margin	= 13,
-		.hsync_len	= 48,
-		.vsync_len	= 3,
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-	},
-};
-
-static struct fb_videomode apf28dev_video_modes[] = {
-	{
-		.name = "LW700",
-		.refresh = 60,
-		.xres = 800,
-		.yres = 480,
-		.pixclock = 30303, /* picosecond */
-		.left_margin = 96,
-		.right_margin = 96, /* at least 3 & 1 */
-		.upper_margin = 0x14,
-		.lower_margin = 0x15,
-		.hsync_len = 64,
-		.vsync_len = 4,
-		.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-	},
-};
-
-static struct fb_videomode cfa10049_video_modes[] = {
-	{
-		.name		= "Himax HX8357-B",
-		.refresh	= 60,
-		.xres		= 320,
-		.yres		= 480,
-		.pixclock	= 108506, /* picosecond (9.216 MHz) */
-		.left_margin	= 2,
-		.right_margin	= 2,
-		.upper_margin	= 2,
-		.lower_margin	= 2,
-		.hsync_len	= 15,
-		.vsync_len	= 15,
-	},
-};
-
-static struct mxsfb_platform_data mxsfb_pdata __initdata;
-
 /*
  * MX28EVK_FLEXCAN_SWITCH is shared between both flexcan controllers
  */
···
 static struct flexcan_platform_data flexcan_pdata[2];
 
 static struct of_dev_auxdata mxs_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("fsl,imx23-lcdif", 0x80030000, NULL, &mxsfb_pdata),
-	OF_DEV_AUXDATA("fsl,imx28-lcdif", 0x80030000, NULL, &mxsfb_pdata),
 	OF_DEV_AUXDATA("fsl,imx28-flexcan", 0x80032000, NULL, &flexcan_pdata[0]),
 	OF_DEV_AUXDATA("fsl,imx28-flexcan", 0x80034000, NULL, &flexcan_pdata[1]),
 	{ /* sentinel */ }
···
 	}
 }
 
-static void __init imx23_evk_init(void)
-{
-	mxsfb_pdata.mode_list = mx23evk_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
-				MXSFB_SYNC_DOTCLK_FAILING_ACT;
-}
-
 static inline void enable_clk_enet_out(void)
 {
 	struct clk *clk = clk_get_sys("enet_out", NULL);
···
 
 static void __init imx28_evk_init(void)
 {
-	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_FSL);
-
-	mxsfb_pdata.mode_list = mx28evk_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
-				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 
 	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
 }
···
 		flexcan_pdata[0].transceiver_switch = mx28evk_flexcan0_switch;
 		flexcan_pdata[1].transceiver_switch = mx28evk_flexcan1_switch;
 	}
-}
-
-static void __init m28evk_init(void)
-{
-	mxsfb_pdata.mode_list = m28evk_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes);
-	mxsfb_pdata.default_bpp = 16;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
-}
-
-static void __init sc_sps1_init(void)
-{
-	enable_clk_enet_out();
 }
 
 static int apx4devkit_phy_fixup(struct phy_device *phy)
···
 	if (IS_BUILTIN(CONFIG_PHYLIB))
 		phy_register_fixup_for_uid(PHY_ID_KSZ8051, MICREL_PHY_ID_MASK,
 					   apx4devkit_phy_fixup);
-
-	mxsfb_pdata.mode_list = apx4devkit_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(apx4devkit_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
-				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 }
 
 #define ENET0_MDC__GPIO_4_0	MXS_GPIO_NR(4, 0)
···
 
 static void __init cfa10049_init(void)
 {
-	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
-
-	mxsfb_pdata.mode_list = cfa10049_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
 }
 
 static void __init cfa10037_init(void)
 {
-	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
-}
-
-static void __init apf28_init(void)
-{
-	enable_clk_enet_out();
-
-	mxsfb_pdata.mode_list = apf28dev_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(apf28dev_video_modes);
-	mxsfb_pdata.default_bpp = 16;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_16BIT;
-	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
-				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 }
 
 static void __init mxs_machine_init(void)
 {
 	if (of_machine_is_compatible("fsl,imx28-evk"))
 		imx28_evk_init();
-	else if (of_machine_is_compatible("fsl,imx23-evk"))
-		imx23_evk_init();
-	else if (of_machine_is_compatible("denx,m28evk"))
-		m28evk_init();
 	else if (of_machine_is_compatible("bluegiga,apx4devkit"))
 		apx4devkit_init();
 	else if (of_machine_is_compatible("crystalfontz,cfa10037"))
 		cfa10037_init();
 	else if (of_machine_is_compatible("crystalfontz,cfa10049"))
 		cfa10049_init();
-	else if (of_machine_is_compatible("armadeus,imx28-apf28"))
-		apf28_init();
-	else if (of_machine_is_compatible("schulercontrol,imx28-sps1"))
-		sc_sps1_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     mxs_auxdata_lookup, NULL);

arch/arm/mach-omap2/board-generic.c

···
 
 static const char *omap3_gp_boards_compat[] __initdata = {
 	"ti,omap3-beagle",
+	"timll,omap3-devkit8000",
 	NULL,
 };
 

arch/arm/mach-omap2/omap_hwmod.c

···
 #include <linux/slab.h>
 #include <linux/bootmem.h>
 #include <linux/cpu.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 
 #include <asm/system_misc.h>
 
···
 }
 
 /**
+ * of_dev_hwmod_lookup - look up needed hwmod from dt blob
+ * @np: struct device_node *
+ * @oh: struct omap_hwmod *
+ *
+ * Parse the dt blob and find out needed hwmod. Recursive function is
+ * implemented to take care hierarchical dt blob parsing.
+ * Return: The device node on success or NULL on failure.
+ */
+static struct device_node *of_dev_hwmod_lookup(struct device_node *np,
+						struct omap_hwmod *oh)
+{
+	struct device_node *np0 = NULL, *np1 = NULL;
+	const char *p;
+
+	for_each_child_of_node(np, np0) {
+		if (of_find_property(np0, "ti,hwmods", NULL)) {
+			p = of_get_property(np0, "ti,hwmods", NULL);
+			if (!strcmp(p, oh->name))
+				return np0;
+			np1 = of_dev_hwmod_lookup(np0, oh);
+			if (np1)
+				return np1;
+		}
+	}
+	return NULL;
+}
+
+/**
  * _init_mpu_rt_base - populate the virtual address for a hwmod
  * @oh: struct omap_hwmod * to locate the virtual address
  *
···
 static void __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data)
 {
 	struct omap_hwmod_addr_space *mem;
-	void __iomem *va_start;
+	void __iomem *va_start = NULL;
+	struct device_node *np;
 
 	if (!oh)
 		return;
···
 	if (!mem) {
 		pr_debug("omap_hwmod: %s: no MPU register target found\n",
 			 oh->name);
-		return;
+
+		/* Extract the IO space from device tree blob */
+		if (!of_have_populated_dt())
+			return;
+
+		np = of_dev_hwmod_lookup(of_find_node_by_name(NULL, "ocp"), oh);
+		if (np)
+			va_start = of_iomap(np, 0);
+	} else {
+		va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start);
 	}
 
-	va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start);
 	if (!va_start) {
 		pr_err("omap_hwmod: %s: Could not ioremap\n", oh->name);
 		return;
···
 	if (oh->_state != _HWMOD_STATE_REGISTERED)
 		return 0;
 
-	_init_mpu_rt_base(oh, NULL);
+	if (oh->class->sysc)
+		_init_mpu_rt_base(oh, NULL);
 
 	r = _init_clocks(oh, NULL);
 	if (r < 0) {

arch/arm/mach-omap2/pmu.c

···
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
+#include <linux/of.h>
+
 #include <asm/pmu.h>
 
 #include "soc.h"
···
 	unsigned oh_num;
 	char **oh_names;
 
+	/* XXX Remove this check when the CTI driver is available */
+	if (cpu_is_omap443x()) {
+		pr_info("ARM PMU: not yet supported on OMAP4430 due to missing CTI driver\n");
+		return 0;
+	}
+
+	if (of_have_populated_dt())
+		return 0;
+
 	/*
 	 * To create an ARM-PMU device the following HWMODs
 	 * are required for the various OMAP2+ devices.
···
 	if (cpu_is_omap443x()) {
 		oh_num = ARRAY_SIZE(omap4430_pmu_oh_names);
 		oh_names = omap4430_pmu_oh_names;
-		/* XXX Remove the next two lines when CTI driver available */
-		pr_info("ARM PMU: not yet supported on OMAP4430 due to missing CTI driver\n");
-		return 0;
 	} else if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
 		oh_num = ARRAY_SIZE(omap3_pmu_oh_names);
 		oh_names = omap3_pmu_oh_names;

arch/arm/mach-omap2/timer.c

···
 };
 
 static struct of_device_id omap_timer_match[] __initdata = {
-	{ .compatible = "ti,omap2-timer", },
+	{ .compatible = "ti,omap2420-timer", },
+	{ .compatible = "ti,omap3430-timer", },
+	{ .compatible = "ti,omap4430-timer", },
+	{ .compatible = "ti,omap5430-timer", },
+	{ .compatible = "ti,am335x-timer", },
+	{ .compatible = "ti,am335x-timer-1ms", },
 	{ }
 };
 

arch/arm/plat-omap/dmtimer.c

···
 static LIST_HEAD(omap_timer_list);
 static DEFINE_SPINLOCK(dm_timer_lock);
 
+enum {
+	REQUEST_ANY = 0,
+	REQUEST_BY_ID,
+	REQUEST_BY_CAP,
+	REQUEST_BY_NODE,
+};
+
 /**
  * omap_dm_timer_read_reg - read timer registers in posted and non-posted mode
  * @timer:      timer pointer over which read operation to perform
···
 	return 0;
 }
 
-struct omap_dm_timer *omap_dm_timer_request(void)
+static struct omap_dm_timer *_omap_dm_timer_request(int req_type, void *data)
 {
 	struct omap_dm_timer *timer = NULL, *t;
+	struct device_node *np = NULL;
 	unsigned long flags;
-	int ret = 0;
+	u32 cap = 0;
+	int id = 0;
+
+	switch (req_type) {
+	case REQUEST_BY_ID:
+		id = *(int *)data;
+		break;
+	case REQUEST_BY_CAP:
+		cap = *(u32 *)data;
+		break;
+	case REQUEST_BY_NODE:
+		np = (struct device_node *)data;
+		break;
+	default:
+		/* REQUEST_ANY */
+		break;
+	}
 
 	spin_lock_irqsave(&dm_timer_lock, flags);
 	list_for_each_entry(t, &omap_timer_list, node) {
 		if (t->reserved)
 			continue;
 
-		timer = t;
-		timer->reserved = 1;
-		break;
+		switch (req_type) {
+		case REQUEST_BY_ID:
+			if (id == t->pdev->id) {
+				timer = t;
+				timer->reserved = 1;
+				goto found;
+			}
+			break;
+		case REQUEST_BY_CAP:
+			if (cap == (t->capability & cap)) {
+				/*
+				 * If timer is not NULL, we have already found
+				 * one timer but it was not an exact match
+				 * because it had more capabilites that what
+				 * was required. Therefore, unreserve the last
+				 * timer found and see if this one is a better
+				 * match.
+				 */
+				if (timer)
+					timer->reserved = 0;
+				timer = t;
+				timer->reserved = 1;
+
+				/* Exit loop early if we find an exact match */
+				if (t->capability == cap)
+					goto found;
+			}
+			break;
+		case REQUEST_BY_NODE:
+			if (np == t->pdev->dev.of_node) {
+				timer = t;
+				timer->reserved = 1;
+				goto found;
+			}
+			break;
+		default:
+			/* REQUEST_ANY */
+			timer = t;
+			timer->reserved = 1;
+			goto found;
+		}
 	}
+found:
 	spin_unlock_irqrestore(&dm_timer_lock, flags);
 
-	if (timer) {
-		ret = omap_dm_timer_prepare(timer);
-		if (ret) {
-			timer->reserved = 0;
-			timer = NULL;
-		}
+	if (timer && omap_dm_timer_prepare(timer)) {
+		timer->reserved = 0;
+		timer = NULL;
 	}
 
 	if (!timer)
···
 
 	return timer;
 }
+
+struct omap_dm_timer *omap_dm_timer_request(void)
+{
+	return _omap_dm_timer_request(REQUEST_ANY, NULL);
+}
 EXPORT_SYMBOL_GPL(omap_dm_timer_request);
 
 struct omap_dm_timer *omap_dm_timer_request_specific(int id)
 {
-	struct omap_dm_timer *timer = NULL, *t;
-	unsigned long flags;
-	int ret = 0;
-
 	/* Requesting timer by ID is not supported when device tree is used */
 	if (of_have_populated_dt()) {
-		pr_warn("%s: Please use omap_dm_timer_request_by_cap()\n",
+		pr_warn("%s: Please use omap_dm_timer_request_by_cap/node()\n",
 			__func__);
 		return NULL;
 	}
 
-	spin_lock_irqsave(&dm_timer_lock, flags);
-	list_for_each_entry(t, &omap_timer_list, node) {
-		if (t->pdev->id == id && !t->reserved) {
-			timer = t;
-			timer->reserved = 1;
-			break;
-		}
-	}
-	spin_unlock_irqrestore(&dm_timer_lock, flags);
-
-	if (timer) {
-		ret = omap_dm_timer_prepare(timer);
-		if (ret) {
-			timer->reserved = 0;
-			timer = NULL;
-		}
-	}
-
-	if (!timer)
-		pr_debug("%s: timer%d request failed!\n", __func__, id);
-
-	return timer;
+	return _omap_dm_timer_request(REQUEST_BY_ID, &id);
 }
 EXPORT_SYMBOL_GPL(omap_dm_timer_request_specific);
 
···
  */
 struct omap_dm_timer *omap_dm_timer_request_by_cap(u32 cap)
 {
-	struct omap_dm_timer *timer = NULL, *t;
-	unsigned long flags;
-
-	if (!cap)
-		return NULL;
-
-	spin_lock_irqsave(&dm_timer_lock, flags);
-	list_for_each_entry(t, &omap_timer_list, node) {
-		if ((!t->reserved) && ((t->capability & cap) == cap)) {
-			/*
-			 * If timer is not NULL, we have already found one timer
-			 * but it was not an exact match because it had more
-			 * capabilites that what was required. Therefore,
-			 * unreserve the last timer found and see if this one
-			 * is a better match.
-			 */
-			if (timer)
-				timer->reserved = 0;
-
-			timer = t;
-			timer->reserved = 1;
-
-			/* Exit loop early if we find an exact match */
-			if (t->capability == cap)
-				break;
-		}
-	}
-	spin_unlock_irqrestore(&dm_timer_lock, flags);
-
-	if (timer && omap_dm_timer_prepare(timer)) {
-		timer->reserved = 0;
-		timer = NULL;
-	}
-
-	if (!timer)
-		pr_debug("%s: timer request failed!\n", __func__);
-
-	return timer;
+	return _omap_dm_timer_request(REQUEST_BY_CAP, &cap);
 }
 EXPORT_SYMBOL_GPL(omap_dm_timer_request_by_cap);
+
+/**
+ * omap_dm_timer_request_by_node - Request a timer by device-tree node
+ * @np:		Pointer to device-tree timer node
+ *
+ * Request a timer based upon a device node pointer. Returns pointer to
+ * timer handle on success and a NULL pointer on failure.
+ */
+struct omap_dm_timer *omap_dm_timer_request_by_node(struct device_node *np)
+{
+	if (!np)
+		return NULL;
+
+	return _omap_dm_timer_request(REQUEST_BY_NODE, np);
+}
+EXPORT_SYMBOL_GPL(omap_dm_timer_request_by_node);
 
 int omap_dm_timer_free(struct omap_dm_timer *timer)
 {
···
 
 void omap_dm_timer_enable(struct omap_dm_timer *timer)
 {
+	int c;
+
 	pm_runtime_get_sync(&timer->pdev->dev);
+
+	if (!(timer->capability & OMAP_TIMER_ALWON)) {
+		if (timer->get_context_loss_count) {
+			c = timer->get_context_loss_count(&timer->pdev->dev);
+			if (c != timer->ctx_loss_count) {
+				omap_timer_restore_context(timer);
+				timer->ctx_loss_count = c;
+			}
+		} else {
+			omap_timer_restore_context(timer);
+		}
+	}
 }
 EXPORT_SYMBOL_GPL(omap_dm_timer_enable);
 
···
 
 	omap_dm_timer_enable(timer);
 
-	if (!(timer->capability & OMAP_TIMER_ALWON)) {
-		if (timer->get_context_loss_count &&
-			timer->get_context_loss_count(&timer->pdev->dev) !=
-				timer->ctx_loss_count)
-			omap_timer_restore_context(timer);
-	}
-
 	l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
 	if (!(l & OMAP_TIMER_CTRL_ST)) {
 		l |= OMAP_TIMER_CTRL_ST;
···
 		rate = clk_get_rate(timer->fclk);
 
 	__omap_dm_timer_stop(timer, timer->posted, rate);
-
-	if (!(timer->capability & OMAP_TIMER_ALWON)) {
-		if (timer->get_context_loss_count)
-			timer->ctx_loss_count =
-				timer->get_context_loss_count(&timer->pdev->dev);
-	}
 
 	/*
 	 * Since the register values are computed and written within
···
 		return -EINVAL;
 
 	omap_dm_timer_enable(timer);
-
-	if (!(timer->capability & OMAP_TIMER_ALWON)) {
-		if (timer->get_context_loss_count &&
-			timer->get_context_loss_count(&timer->pdev->dev) !=
-				timer->ctx_loss_count)
-			omap_timer_restore_context(timer);
-	}
 
 	l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
 	if (autoreload) {
···
 }
 EXPORT_SYMBOL_GPL(omap_dm_timers_active);
 
+static const struct of_device_id omap_timer_match[];
+
 /**
  * omap_dm_timer_probe - probe function called for every registered device
  * @pdev:	pointer to current timer platform device
···
 	struct omap_dm_timer *timer;
 	struct resource *mem, *irq;
 	struct device *dev = &pdev->dev;
-	struct dmtimer_platform_data *pdata = pdev->dev.platform_data;
+	const struct of_device_id *match;
+	const struct dmtimer_platform_data *pdata;
+
+	match = of_match_device(of_match_ptr(omap_timer_match), dev);
+	pdata = match ? match->data : dev->platform_data;
 
 	if (!pdata && !dev->of_node) {
 		dev_err(dev, "%s: no platform data.\n", __func__);
···
 			timer->capability |= OMAP_TIMER_SECURE;
 	} else {
 		timer->id = pdev->id;
-		timer->errata = pdata->timer_errata;
 		timer->capability = pdata->timer_capability;
 		timer->reserved = omap_dm_timer_reserved_systimer(timer->id);
 		timer->get_context_loss_count = pdata->get_context_loss_count;
 	}
+
+	if (pdata)
+		timer->errata = pdata->timer_errata;
 
 	timer->irq = irq->start;
 	timer->pdev = pdev;
···
 	return ret;
 }
 
+static const struct dmtimer_platform_data omap3plus_pdata = {
+	.timer_errata = OMAP_TIMER_ERRATA_I103_I767,
+};
+
 static const struct of_device_id omap_timer_match[] = {
-	{ .compatible = "ti,omap2-timer", },
+	{
+		.compatible = "ti,omap2420-timer",
+	},
+	{
+		.compatible = "ti,omap3430-timer",
+		.data = &omap3plus_pdata,
+	},
+	{
+		.compatible = "ti,omap4430-timer",
+		.data = &omap3plus_pdata,
+	},
+	{
+		.compatible = "ti,omap5430-timer",
+		.data = &omap3plus_pdata,
+	},
+	{
+		.compatible = "ti,am335x-timer",
+		.data = &omap3plus_pdata,
+	},
+	{
+		.compatible = "ti,am335x-timer-1ms",
+		.data = &omap3plus_pdata,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap_timer_match);

arch/arm/plat-omap/include/plat/dmtimer.h

···
 struct omap_dm_timer *omap_dm_timer_request(void);
 struct omap_dm_timer *omap_dm_timer_request_specific(int timer_id);
 struct omap_dm_timer *omap_dm_timer_request_by_cap(u32 cap);
+struct omap_dm_timer *omap_dm_timer_request_by_node(struct device_node *np);
 int omap_dm_timer_free(struct omap_dm_timer *timer);
 void omap_dm_timer_enable(struct omap_dm_timer *timer);
 void omap_dm_timer_disable(struct omap_dm_timer *timer);

drivers/dma/mxs-dma.c

···
 #include <linux/stmp_device.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_dma.h>
 
 #include <asm/irq.h>
 
···
 	struct dma_device		dma_device;
 	struct device_dma_parameters	dma_parms;
 	struct mxs_dma_chan		mxs_chans[MXS_DMA_CHANNELS];
+	struct platform_device		*pdev;
+	unsigned int			nr_channels;
 };
 
 struct mxs_dma_type {
···
 	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
 	int ret;
 
-	if (!data)
-		return -EINVAL;
-
-	mxs_chan->chan_irq = data->chan_irq;
+	if (data)
+		mxs_chan->chan_irq = data->chan_irq;
 
 	mxs_chan->ccw = dma_alloc_coherent(mxs_dma->dma_device.dev,
 				CCW_BLOCK_SIZE, &mxs_chan->ccw_phys,
···
 	return ret;
 }
 
+struct mxs_dma_filter_param {
+	struct device_node *of_node;
+	unsigned int chan_id;
+};
+
+static bool mxs_dma_filter_fn(struct dma_chan *chan, void *fn_param)
+{
+	struct mxs_dma_filter_param *param = fn_param;
+	struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+	int chan_irq;
+
+	if (mxs_dma->dma_device.dev->of_node != param->of_node)
+		return false;
+
+	if (chan->chan_id != param->chan_id)
+		return false;
+
+	chan_irq = platform_get_irq(mxs_dma->pdev, param->chan_id);
+	if (chan_irq < 0)
+		return false;
+
+	mxs_chan->chan_irq = chan_irq;
+
+	return true;
+}
+
+struct dma_chan *mxs_dma_xlate(struct of_phandle_args *dma_spec,
+			       struct of_dma *ofdma)
+{
+	struct mxs_dma_engine *mxs_dma = ofdma->of_dma_data;
+	dma_cap_mask_t mask = mxs_dma->dma_device.cap_mask;
+	struct mxs_dma_filter_param param;
+
+	if (dma_spec->args_count != 1)
+		return NULL;
+
+	param.of_node = ofdma->of_node;
+	param.chan_id = dma_spec->args[0];
+
+	if (param.chan_id >= mxs_dma->nr_channels)
+		return NULL;
+
+	return dma_request_channel(mask, mxs_dma_filter_fn, &param);
+}
+
 static int __init mxs_dma_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
 	const struct platform_device_id *id_entry;
 	const struct of_device_id *of_id;
 	const struct mxs_dma_type *dma_type;
···
 	struct resource *iores;
 	int ret, i;
 
-	mxs_dma = kzalloc(sizeof(*mxs_dma), GFP_KERNEL);
+	mxs_dma = devm_kzalloc(&pdev->dev, sizeof(*mxs_dma), GFP_KERNEL);
 	if (!mxs_dma)
 		return -ENOMEM;
+
+	ret = of_property_read_u32(np, "dma-channels", &mxs_dma->nr_channels);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to read dma-channels\n");
+		return ret;
+	}
 
 	of_id = of_match_device(mxs_dma_dt_ids, &pdev->dev);
 	if (of_id)
···
 	mxs_dma->dev_id = dma_type->id;
 
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mxs_dma->base = devm_ioremap_resource(&pdev->dev, iores);
+	if (IS_ERR(mxs_dma->base))
+		return PTR_ERR(mxs_dma->base);
 
-	if (!request_mem_region(iores->start, resource_size(iores),
-				pdev->name)) {
-		ret = -EBUSY;
-		goto err_request_region;
-	}
-
-	mxs_dma->base = ioremap(iores->start, resource_size(iores));
-	if (!mxs_dma->base) {
-		ret = -ENOMEM;
-		goto err_ioremap;
-	}
-
-	mxs_dma->clk = clk_get(&pdev->dev, NULL);
-	if (IS_ERR(mxs_dma->clk)) {
-		ret = PTR_ERR(mxs_dma->clk);
-		goto err_clk;
-	}
+	mxs_dma->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(mxs_dma->clk))
+		return PTR_ERR(mxs_dma->clk);
 
 	dma_cap_set(DMA_SLAVE, mxs_dma->dma_device.cap_mask);
 	dma_cap_set(DMA_CYCLIC, mxs_dma->dma_device.cap_mask);
···
 
 	ret = mxs_dma_init(mxs_dma);
 	if (ret)
-		goto err_init;
+		return ret;
 
+	mxs_dma->pdev = pdev;
 	mxs_dma->dma_device.dev = &pdev->dev;
 
 	/* mxs_dma gets 65535 bytes maximum sg size */
···
 	ret = dma_async_device_register(&mxs_dma->dma_device);
 	if (ret) {
 		dev_err(mxs_dma->dma_device.dev, "unable to register\n");
-		goto err_init;
+		return ret;
+	}
+
+	ret = of_dma_controller_register(np, mxs_dma_xlate, mxs_dma);
+	if (ret) {
+		dev_err(mxs_dma->dma_device.dev,
+			"failed to register controller\n");
+		dma_async_device_unregister(&mxs_dma->dma_device);
 	}
 
 	dev_info(mxs_dma->dma_device.dev, "initialized\n");
 
 	return 0;
-
-err_init:
-	clk_put(mxs_dma->clk);
-err_clk:
-	iounmap(mxs_dma->base);
-err_ioremap:
-	release_mem_region(iores->start, resource_size(iores));
-err_request_region:
-	kfree(mxs_dma);
-	return ret;
 }
 
 static struct platform_driver mxs_dma_driver = {

drivers/i2c/busses/i2c-mxs.c

···
 #include <linux/of_i2c.h>
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
-#include <linux/fsl/mxs-dma.h>
 
 #define DRIVER_NAME "mxs-i2c"
 
···
 	uint32_t timing1;
 
 	/* DMA support components */
-	int				dma_channel;
 	struct dma_chan         	*dmach;
-	struct mxs_dma_data		dma_data;
 	uint32_t			pio_data[2];
 	uint32_t			addr_data;
 	struct scatterlist		sg_io[2];
···
 	.functionality = mxs_i2c_func,
 };
 
-static bool mxs_i2c_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct mxs_i2c_dev *i2c = param;
-
-	if (!mxs_dma_is_apbx(chan))
-		return false;
-
-	if (chan->chan_id != i2c->dma_channel)
-		return false;
-
-	chan->private = &i2c->dma_data;
-
-	return true;
-}
-
 static void mxs_i2c_derive_timing(struct mxs_i2c_dev *i2c, int speed)
 {
 	/* The I2C block clock run at 24MHz */
···
 	struct device_node *node = dev->of_node;
 	int ret;
 
-	/*
-	 * TODO: This is a temporary solution and should be changed
-	 * to use generic DMA binding later when the helpers get in.
-	 */
-	ret = of_property_read_u32(node, "fsl,i2c-dma-channel",
-				   &i2c->dma_channel);
-	if (ret) {
-		dev_err(dev, "Failed to get DMA channel!\n");
-		return -ENODEV;
-	}
-
 	ret = of_property_read_u32(node, "clock-frequency", &speed);
 	if (ret) {
 		dev_warn(dev, "No I2C speed selected, using 100kHz\n");
···
 	struct pinctrl *pinctrl;
 	struct resource *res;
 	resource_size_t res_size;
-	int err, irq, dmairq;
-	dma_cap_mask_t mask;
+	int err, irq;
 
 	pinctrl = devm_pinctrl_get_select_default(dev);
 	if (IS_ERR(pinctrl))
···
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq = platform_get_irq(pdev, 0);
-	dmairq = platform_get_irq(pdev, 1);
 
-	if (!res || irq < 0 || dmairq < 0)
+	if (!res || irq < 0)
 		return -ENOENT;
 
 	res_size = resource_size(res);
···
 	}
 
 	/* Setup the DMA */
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-	i2c->dma_data.chan_irq = dmairq;
-	i2c->dmach = dma_request_channel(mask, mxs_i2c_dma_filter, i2c);
+	i2c->dmach = dma_request_slave_channel(dev, "rx-tx");
 	if (!i2c->dmach) {
 		dev_err(dev, "Failed to request dma\n");
 		return -ENODEV;

drivers/mmc/host/mxs-mmc.c

···
 	.enable_sdio_irq = mxs_mmc_enable_sdio_irq,
 };
 
-static bool mxs_mmc_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct mxs_mmc_host *host = param;
-	struct mxs_ssp *ssp = &host->ssp;
-
-	if (!mxs_dma_is_apbh(chan))
-		return false;
-
-	if (chan->chan_id != ssp->dma_channel)
-		return false;
-
-	chan->private = &ssp->dma_data;
-
-	return true;
-}
-
 static struct platform_device_id mxs_ssp_ids[] = {
 	{
 		.name = "imx23-mmc",
···
 	struct device_node *np = pdev->dev.of_node;
 	struct mxs_mmc_host *host;
 	struct mmc_host *mmc;
-	struct resource *iores, *dmares;
+	struct resource *iores;
 	struct pinctrl *pinctrl;
-	int ret = 0, irq_err, irq_dma;
-	dma_cap_mask_t mask;
+	int ret = 0, irq_err;
 	struct regulator *reg_vmmc;
 	enum of_gpio_flags flags;
 	struct mxs_ssp *ssp;
 	u32 bus_width = 0;
 
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
 	irq_err = platform_get_irq(pdev, 0);
-	irq_dma = platform_get_irq(pdev, 1);
-	if (!iores || irq_err < 0 || irq_dma < 0)
+	if (!iores || irq_err < 0)
 		return -EINVAL;
 
 	mmc = mmc_alloc_host(sizeof(struct mxs_mmc_host), &pdev->dev);
···
 		goto out_mmc_free;
 	}
 
-	if (np) {
-		ssp->devid = (enum mxs_ssp_id) of_id->data;
-		/*
-		 * TODO: This is a temporary solution and should be changed
-		 * to use generic DMA binding later when the helpers get in.
-		 */
-		ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
-					   &ssp->dma_channel);
-		if (ret) {
-			dev_err(mmc_dev(host->mmc),
-				"failed to get dma channel\n");
-			goto out_mmc_free;
-		}
-	} else {
-		ssp->devid = pdev->id_entry->driver_data;
-		ssp->dma_channel = dmares->start;
-	}
+	ssp->devid = (enum mxs_ssp_id) of_id->data;
 
 	host->mmc = mmc;
 	host->sdio_irq_en = 0;
···
 
 	mxs_mmc_reset(host);
 
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-	ssp->dma_data.chan_irq = irq_dma;
-	ssp->dmach = dma_request_channel(mask, mxs_mmc_dma_filter, host);
+	ssp->dmach = dma_request_slave_channel(&pdev->dev, "rx-tx");
 	if (!ssp->dmach) {
 		dev_err(mmc_dev(host->mmc),
 			"%s: failed to request dma\n", __func__);

drivers/mtd/nand/gpmi-nand/gpmi-nand.c

···
 #define GPMI_NAND_GPMI_REGS_ADDR_RES_NAME  "gpmi-nand"
 #define GPMI_NAND_BCH_REGS_ADDR_RES_NAME   "bch"
 #define GPMI_NAND_BCH_INTERRUPT_RES_NAME   "bch"
-#define GPMI_NAND_DMA_INTERRUPT_RES_NAME   "gpmi-dma"
 
 /* add our owner bbt descriptor */
 static uint8_t scan_ff_pattern[] = { 0xff };
···
 		free_irq(i, this);
 }
 
-static bool gpmi_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct gpmi_nand_data *this = param;
-	int dma_channel = (int)this->private;
-
-	if (!mxs_dma_is_apbh(chan))
-		return false;
-	/*
-	 * only catch the GPMI dma channels :
-	 *	for mx23 :	MX23_DMA_GPMI0 ~ MX23_DMA_GPMI3
-	 *		(These four channels share the same IRQ!)
-	 *
-	 *	for mx28 :	MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7
-	 *		(These eight channels share the same IRQ!)
-	 */
-	if (dma_channel == chan->chan_id) {
-		chan->private = &this->dma_data;
-		return true;
-	}
-	return false;
-}
-
 static void release_dma_channels(struct gpmi_nand_data *this)
 {
 	unsigned int i;
···
 static int acquire_dma_channels(struct gpmi_nand_data *this)
 {
 	struct platform_device *pdev = this->pdev;
-	struct resource *r_dma;
-	struct device_node *dn;
-	u32 dma_channel;
-	int ret;
 	struct dma_chan *dma_chan;
-	dma_cap_mask_t mask;
-
-	/* dma channel, we only use the first one. */
-	dn = pdev->dev.of_node;
-	ret = of_property_read_u32(dn, "fsl,gpmi-dma-channel", &dma_channel);
-	if (ret) {
-		pr_err("unable to get DMA channel from dt.\n");
-		goto acquire_err;
-	}
-	this->private = (void *)dma_channel;
-
-	/* gpmi dma interrupt */
-	r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
-					GPMI_NAND_DMA_INTERRUPT_RES_NAME);
-	if (!r_dma) {
-		pr_err("Can't get resource for DMA\n");
-		goto acquire_err;
-	}
-	this->dma_data.chan_irq = r_dma->start;
 
 	/* request dma channel */
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-
-	dma_chan = dma_request_channel(mask, gpmi_dma_filter, this);
+	dma_chan = dma_request_slave_channel(&pdev->dev, "rx-tx");
 	if (!dma_chan) {
 		pr_err("Failed to request DMA channel.\n");
 		goto acquire_err;

drivers/mtd/nand/gpmi-nand/gpmi-nand.h

···
 #include <linux/mtd/nand.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
 
 #define GPMI_CLK_MAX 5 /* MX6Q needs five clocks */
 struct resources {
···
 	/* DMA channels */
 #define DMA_CHANS		8
 	struct dma_chan		*dma_chans[DMA_CHANS];
-	struct mxs_dma_data	dma_data;
 	enum dma_ops_type	last_dma_type;
 	enum dma_ops_type	dma_type;
 	struct completion	dma_done;

drivers/net/ethernet/freescale/fec.h

···
 
 	struct clk *clk_ipg;
 	struct clk *clk_ahb;
+	struct clk *clk_enet_out;
 	struct clk *clk_ptp;
 
 	/* The saved address of a sent-in-place packet/buffer, for skfree(). */

drivers/net/ethernet/freescale/fec_main.c

···
 		goto failed_clk;
 	}
 
+	/* enet_out is optional, depends on board */
+	fep->clk_enet_out = devm_clk_get(&pdev->dev, "enet_out");
+	if (IS_ERR(fep->clk_enet_out))
+		fep->clk_enet_out = NULL;
+
 	fep->clk_ptp = devm_clk_get(&pdev->dev, "ptp");
 	fep->bufdesc_ex =
 		pdev->id_entry->driver_data & FEC_QUIRK_HAS_BUFDESC_EX;
 	if (IS_ERR(fep->clk_ptp)) {
-		ret = PTR_ERR(fep->clk_ptp);
+		fep->clk_ptp = NULL;
 		fep->bufdesc_ex = 0;
 	}
 
 	clk_prepare_enable(fep->clk_ahb);
 	clk_prepare_enable(fep->clk_ipg);
-	if (!IS_ERR(fep->clk_ptp))
-		clk_prepare_enable(fep->clk_ptp);
+	clk_prepare_enable(fep->clk_enet_out);
+	clk_prepare_enable(fep->clk_ptp);
 
 	reg_phy = devm_regulator_get(&pdev->dev, "phy");
 	if (!IS_ERR(reg_phy)) {
···
 failed_regulator:
 	clk_disable_unprepare(fep->clk_ahb);
 	clk_disable_unprepare(fep->clk_ipg);
-	if (!IS_ERR(fep->clk_ptp))
-		clk_disable_unprepare(fep->clk_ptp);
+	clk_disable_unprepare(fep->clk_enet_out);
+	clk_disable_unprepare(fep->clk_ptp);
 failed_pin:
 failed_clk:
 failed_ioremap:
···
 	clk_disable_unprepare(fep->clk_ptp);
 	if (fep->ptp_clock)
 		ptp_clock_unregister(fep->ptp_clock);
+	clk_disable_unprepare(fep->clk_enet_out);
 	clk_disable_unprepare(fep->clk_ahb);
 	clk_disable_unprepare(fep->clk_ipg);
 	for (i = 0; i < FEC_IRQ_NUM; i++) {
···
 		fec_stop(ndev);
 		netif_device_detach(ndev);
 	}
+	clk_disable_unprepare(fep->clk_enet_out);
 	clk_disable_unprepare(fep->clk_ahb);
 	clk_disable_unprepare(fep->clk_ipg);
 
···
 	struct net_device *ndev = dev_get_drvdata(dev);
 	struct fec_enet_private *fep = netdev_priv(ndev);
 
+	clk_prepare_enable(fep->clk_enet_out);
 	clk_prepare_enable(fep->clk_ahb);
 	clk_prepare_enable(fep->clk_ipg);
 	if (netif_running(ndev)) {

drivers/spi/spi-davinci.c

···
 #if defined(CONFIG_OF)
 static const struct of_device_id davinci_spi_of_match[] = {
 	{
-		.compatible = "ti,dm644x-spi",
+		.compatible = "ti,dm6441-spi",
 	},
 	{
-		.compatible = "ti,da8xx-spi",
+		.compatible = "ti,da830-spi",
 		.data = (void *)SPI_VERSION_2,
 	},
 	{ },

drivers/spi/spi-mxs.c

···
 	return status;
 }
 
-static bool mxs_ssp_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct mxs_ssp *ssp = param;
-
-	if (!mxs_dma_is_apbh(chan))
-		return false;
-
-	if (chan->chan_id != ssp->dma_channel)
-		return false;
-
-	chan->private = &ssp->dma_data;
-
-	return true;
-}
-
 static const struct of_device_id mxs_spi_dt_ids[] = {
 	{ .compatible = "fsl,imx23-spi", .data = (void *) IMX23_SSP, },
 	{ .compatible = "fsl,imx28-spi", .data = (void *) IMX28_SSP, },
···
 	struct spi_master *master;
 	struct mxs_spi *spi;
 	struct mxs_ssp *ssp;
-	struct resource *iores, *dmares;
+	struct resource *iores;
 	struct pinctrl *pinctrl;
 	struct clk *clk;
 	void __iomem *base;
-	int devid, dma_channel, clk_freq;
-	int ret = 0, irq_err, irq_dma;
-	dma_cap_mask_t mask;
+	int devid, clk_freq;
+	int ret = 0, irq_err;
 
 	/*
 	 * Default clock speed for the SPI core. 160MHz seems to
···
 
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq_err = platform_get_irq(pdev, 0);
-	irq_dma = platform_get_irq(pdev, 1);
-	if (!iores || irq_err < 0 || irq_dma < 0)
+	if (!iores || irq_err < 0)
 		return -EINVAL;
 
 	base = devm_ioremap_resource(&pdev->dev, iores);
···
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
 
-	if (np) {
-		devid = (enum mxs_ssp_id) of_id->data;
-		/*
-		 * TODO: This is a temporary solution and should be changed
-		 * to use generic DMA binding later when the helpers get in.
-		 */
-		ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
-					   &dma_channel);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"Failed to get DMA channel\n");
-			return -EINVAL;
-		}
-
-		ret = of_property_read_u32(np, "clock-frequency",
-					   &clk_freq);
-		if (ret)
-			clk_freq = clk_freq_default;
-	} else {
-		dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-		if (!dmares)
-			return -EINVAL;
-		devid = pdev->id_entry->driver_data;
-		dma_channel = dmares->start;
+	devid = (enum mxs_ssp_id) of_id->data;
+	ret = of_property_read_u32(np, "clock-frequency",
+				   &clk_freq);
+	if (ret)
 		clk_freq = clk_freq_default;
-	}
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*spi));
 	if (!master)
···
 	ssp->clk = clk;
 	ssp->base = base;
 	ssp->devid = devid;
-	ssp->dma_channel = dma_channel;
 
 	init_completion(&spi->c);
 
···
 	if (ret)
 		goto out_master_free;
 
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-	ssp->dma_data.chan_irq = irq_dma;
-	ssp->dmach = dma_request_channel(mask, mxs_ssp_dma_filter, ssp);
+	ssp->dmach = dma_request_slave_channel(&pdev->dev, "rx-tx");
 	if (!ssp->dmach) {
 		dev_err(ssp->dev, "Failed to request DMA\n");
 		ret = -ENODEV;

drivers/tty/serial/mxs-auart.c

···
 #include <linux/pinctrl/consumer.h>
 #include <linux/of_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
 
 #include <asm/cacheflush.h>
 
···
 	struct device *dev;
 
 	/* for DMA */
-	struct mxs_dma_data dma_data;
-	int dma_channel_rx, dma_channel_tx;
-	int dma_irq_rx, dma_irq_tx;
-	int dma_channel;
-
 	struct scatterlist tx_sgl;
 	struct dma_chan	*tx_dma_chan;
 	void *tx_dma_buf;
···
 	return mctrl;
 }
 
-static bool mxs_auart_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct mxs_auart_port *s = param;
-
-	if (!mxs_dma_is_apbx(chan))
-		return false;
-
-	if (s->dma_channel == chan->chan_id) {
-		chan->private = &s->dma_data;
-		return true;
-	}
-	return false;
-}
-
 static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s);
 static void dma_rx_callback(void *arg)
 {
···
 
 static int mxs_auart_dma_init(struct mxs_auart_port *s)
 {
-	dma_cap_mask_t mask;
-
 	if (auart_dma_enabled(s))
 		return 0;
 
-	/* We do not get the right DMA channels. */
-	if (s->dma_channel_rx == -1 || s->dma_channel_tx == -1)
-		return -EINVAL;
-
 	/* init for RX */
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-	s->dma_channel = s->dma_channel_rx;
-	s->dma_data.chan_irq = s->dma_irq_rx;
-	s->rx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+	s->rx_dma_chan = dma_request_slave_channel(s->dev, "rx");
 	if (!s->rx_dma_chan)
 		goto err_out;
 	s->rx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
···
 		goto err_out;
 
 	/* init for TX */
-	s->dma_channel = s->dma_channel_tx;
-	s->dma_data.chan_irq = s->dma_irq_tx;
-	s->tx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+	s->tx_dma_chan = dma_request_slave_channel(s->dev, "tx");
 	if (!s->tx_dma_chan)
 		goto err_out;
 	s->tx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
···
 		struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
-	u32 dma_channel[2];
 	int ret;
 
 	if (!np)
···
 	}
 	s->port.line = ret;
 
-	s->dma_irq_rx = platform_get_irq(pdev, 1);
-	s->dma_irq_tx = platform_get_irq(pdev, 2);
+	s->flags |= MXS_AUART_DMA_CONFIG;
 
-	ret = of_property_read_u32_array(np, "fsl,auart-dma-channel",
-					dma_channel, 2);
-	if (ret == 0) {
-		s->dma_channel_rx = dma_channel[0];
-		s->dma_channel_tx = dma_channel[1];
-
-		s->flags |= MXS_AUART_DMA_CONFIG;
-	} else {
-		s->dma_channel_rx = -1;
-		s->dma_channel_tx = -1;
-	}
 	return 0;
 }
 

drivers/video/Kconfig

···
 	select FB_CFB_FILLRECT
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
+	select FB_MODE_HELPERS
+	select OF_VIDEOMODE
 	help
 	  Framebuffer support for the MXS SoC.
 

drivers/video/mxsfb.c

···
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
+#include <video/of_display_timing.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/dma-mapping.h>
 #include <linux/io.h>
 #include <linux/pinctrl/consumer.h>
-#include <linux/mxsfb.h>
+#include <linux/fb.h>
+#include <linux/regulator/consumer.h>
+#include <video/videomode.h>
 
 #define REG_SET	4
 #define REG_CLR	8
···
 #define VDCTRL0_ENABLE_PRESENT		(1 << 28)
 #define VDCTRL0_VSYNC_ACT_HIGH		(1 << 27)
 #define VDCTRL0_HSYNC_ACT_HIGH		(1 << 26)
-#define VDCTRL0_DOTCLK_ACT_FAILING	(1 << 25)
+#define VDCTRL0_DOTCLK_ACT_FALLING	(1 << 25)
 #define VDCTRL0_ENABLE_ACT_HIGH		(1 << 24)
 #define VDCTRL0_VSYNC_PERIOD_UNIT	(1 << 21)
 #define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT	(1 << 20)
···
 #define BLUE 2
 #define TRANSP 3
 
+#define STMLCDIF_8BIT  1 /** pixel data bus to the display is of 8 bit width */
+#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
+#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
+#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
+
+#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT	(1 << 6)
+#define MXSFB_SYNC_DOTCLK_FALLING_ACT	(1 << 7) /* negtive edge sampling */
+
 enum mxsfb_devtype {
 	MXSFB_V3,
 	MXSFB_V4,
···
 	unsigned ld_intf_width;
 	unsigned dotclk_delay;
 	const struct mxsfb_devdata *devdata;
-	int mapped;
 	u32 sync;
+	struct regulator *reg_lcd;
 };
 
 #define mxsfb_is_v3(host) (host->devdata->ipversion == 3)
···
 {
 	struct mxsfb_info *host = to_imxfb_host(fb_info);
 	u32 reg;
+	int ret;
 
 	dev_dbg(&host->pdev->dev, "%s\n", __func__);
+
+	if (host->reg_lcd) {
+		ret = regulator_enable(host->reg_lcd);
+		if (ret) {
+			dev_err(&host->pdev->dev,
+				"lcd regulator enable failed:	%d\n", ret);
+			return;
+		}
+	}
 
 	clk_prepare_enable(host->clk);
 	clk_set_rate(host->clk, PICOS2KHZ(fb_info->var.pixclock) * 1000U);
···
 	struct mxsfb_info *host = to_imxfb_host(fb_info);
 	unsigned loop;
 	u32 reg;
+	int ret;
 
 	dev_dbg(&host->pdev->dev, "%s\n", __func__);
 
···
 	clk_disable_unprepare(host->clk);
 
 	host->enabled = 0;
+
+	if (host->reg_lcd) {
+		ret = regulator_disable(host->reg_lcd);
+		if (ret)
+			dev_err(&host->pdev->dev,
+				"lcd regulator disable failed: %d\n", ret);
+	}
 }
 
 static int mxsfb_set_par(struct fb_info *fb_info)
···
 		vdctrl0 |= VDCTRL0_VSYNC_ACT_HIGH;
 	if (host->sync & MXSFB_SYNC_DATA_ENABLE_HIGH_ACT)
 		vdctrl0 |= VDCTRL0_ENABLE_ACT_HIGH;
-	if (host->sync & MXSFB_SYNC_DOTCLK_FAILING_ACT)
-		vdctrl0 |= VDCTRL0_DOTCLK_ACT_FAILING;
+	if (host->sync & MXSFB_SYNC_DOTCLK_FALLING_ACT)
+		vdctrl0 |= VDCTRL0_DOTCLK_ACT_FALLING;
 
 	writel(vdctrl0, host->base + LCDC_VDCTRL0);
 
···
 	return 0;
 }
 
+static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host)
+{
+	struct fb_info *fb_info = &host->fb_info;
+	struct fb_var_screeninfo *var = &fb_info->var;
+	struct device *dev = &host->pdev->dev;
+	struct device_node *np = host->pdev->dev.of_node;
+	struct device_node *display_np;
+	struct device_node *timings_np;
+	struct display_timings *timings;
+	u32 width;
+	int i;
+	int ret = 0;
+
+	display_np = of_parse_phandle(np, "display", 0);
+	if (!display_np) {
+		dev_err(dev, "failed to find display phandle\n");
+		return -ENOENT;
+	}
+
+	ret = of_property_read_u32(display_np, "bus-width", &width);
+	if (ret < 0) {
+		dev_err(dev, "failed to get property bus-width\n");
+		goto put_display_node;
+	}
+
+	switch (width) {
+	case 8:
+		host->ld_intf_width = STMLCDIF_8BIT;
+		break;
+	case 16:
+		host->ld_intf_width = STMLCDIF_16BIT;
+		break;
+	case 18:
+		host->ld_intf_width = STMLCDIF_18BIT;
+		break;
+	case 24:
+		host->ld_intf_width = STMLCDIF_24BIT;
+		break;
+	default:
+		dev_err(dev, "invalid bus-width value\n");
+		ret = -EINVAL;
+		goto put_display_node;
+	}
+
+	ret = of_property_read_u32(display_np, "bits-per-pixel",
+				   &var->bits_per_pixel);
+	if (ret < 0) {
+		dev_err(dev, "failed to get property bits-per-pixel\n");
+		goto put_display_node;
+	}
+
+	timings = of_get_display_timings(display_np);
+	if (!timings) {
+		dev_err(dev, "failed to get display timings\n");
+		ret = -ENOENT;
+		goto put_display_node;
+	}
+
+	timings_np = of_find_node_by_name(display_np,
+					  "display-timings");
+	if (!timings_np) {
+		dev_err(dev, "failed to find display-timings node\n");
+		ret = -ENOENT;
+		goto put_display_node;
+	}
+
+	for (i = 0; i < of_get_child_count(timings_np); i++) {
+		struct videomode vm;
+		struct fb_videomode fb_vm;
+
+		ret = videomode_from_timing(timings, &vm, i);
+		if (ret < 0)
+			goto put_timings_node;
+		ret = fb_videomode_from_videomode(&vm, &fb_vm);
+		if (ret < 0)
+			goto put_timings_node;
+
+		if (vm.data_flags & DISPLAY_FLAGS_DE_HIGH)
+			host->sync |= MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
+		if (vm.data_flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
+			host->sync |= MXSFB_SYNC_DOTCLK_FALLING_ACT;
+		fb_add_videomode(&fb_vm, &fb_info->modelist);
+	}
+
+put_timings_node:
+	of_node_put(timings_np);
+put_display_node:
+	of_node_put(display_np);
+	return ret;
+}
+
 static int mxsfb_init_fbinfo(struct mxsfb_info *host)
 {
 	struct fb_info *fb_info = &host->fb_info;
 	struct fb_var_screeninfo *var = &fb_info->var;
-	struct mxsfb_platform_data *pdata = host->pdev->dev.platform_data;
 	dma_addr_t fb_phys;
 	void *fb_virt;
-	unsigned fb_size = pdata->fb_size;
+	unsigned fb_size;
+	int ret;
 
 	fb_info->fbops = &mxsfb_ops;
 	fb_info->flags = FBINFO_FLAG_DEFAULT | FBINFO_READS_FAST;
···
 	fb_info->fix.visual = FB_VISUAL_TRUECOLOR,
 	fb_info->fix.accel = FB_ACCEL_NONE;
 
-	var->bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
+	ret = mxsfb_init_fbinfo_dt(host);
+	if (ret)
+		return ret;
+
 	var->nonstd = 0;
 	var->activate = FB_ACTIVATE_NOW;
 	var->accel_flags = 0;
 	var->vmode = FB_VMODE_NONINTERLACED;
 
-	host->dotclk_delay = pdata->dotclk_delay;
-	host->ld_intf_width = pdata->ld_intf_width;
-
 	/* Memory allocation for framebuffer */
-	if (pdata->fb_phys) {
-		if (!fb_size)
-			return -EINVAL;
+	fb_size = SZ_2M;
+	fb_virt = alloc_pages_exact(fb_size, GFP_DMA);
+	if (!fb_virt)
+		return -ENOMEM;
 
-		fb_phys = pdata->fb_phys;
-
-		if (!request_mem_region(fb_phys, fb_size, host->pdev->name))
-			return -ENOMEM;
-
-		fb_virt = ioremap(fb_phys, fb_size);
-		if (!fb_virt) {
-			release_mem_region(fb_phys, fb_size);
-			return -ENOMEM;
-		}
-		host->mapped = 1;
-	} else {
-		if (!fb_size)
-			fb_size = SZ_2M; /* default */
-		fb_virt = alloc_pages_exact(fb_size, GFP_DMA);
-		if (!fb_virt)
-			return -ENOMEM;
-
-		fb_phys = virt_to_phys(fb_virt);
-	}
+	fb_phys = virt_to_phys(fb_virt);
 
 	fb_info->fix.smem_start = fb_phys;
 	fb_info->screen_base = fb_virt;
···
 {
 	struct fb_info *fb_info = &host->fb_info;
 
-	if (host->mapped) {
-		iounmap(fb_info->screen_base);
-		release_mem_region(fb_info->fix.smem_start,
-				fb_info->screen_size);
-	} else {
-		free_pages_exact(fb_info->screen_base, fb_info->fix.smem_len);
-	}
+	free_pages_exact(fb_info->screen_base, fb_info->fix.smem_len);
 }
 
 static struct platform_device_id mxsfb_devtype[] = {
···
 {
 	const struct of_device_id *of_id =
 			of_match_device(mxsfb_dt_ids, &pdev->dev);
-	struct mxsfb_platform_data *pdata = pdev->dev.platform_data;
 	struct resource *res;
 	struct mxsfb_info *host;
 	struct fb_info *fb_info;
 	struct fb_modelist *modelist;
 	struct pinctrl *pinctrl;
-	int panel_enable;
-	enum of_gpio_flags flags;
-	int i, ret;
+	int ret;
 
 	if (of_id)
 		pdev->id_entry = of_id->data;
-
-	if (!pdata) {
-		dev_err(&pdev->dev, "No platformdata. Giving up\n");
-		return -ENODEV;
-	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
···
 		return -ENODEV;
 	}
 
-	if (!request_mem_region(res->start, resource_size(res), pdev->name))
-		return -EBUSY;
-
 	fb_info = framebuffer_alloc(sizeof(struct mxsfb_info), &pdev->dev);
 	if (!fb_info) {
 		dev_err(&pdev->dev, "Failed to allocate fbdev\n");
-		ret = -ENOMEM;
-		goto error_alloc_info;
+		return -ENOMEM;
 	}
 
 	host = to_imxfb_host(fb_info);
 
-	host->base = ioremap(res->start, resource_size(res));
-	if (!host->base) {
+	host->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(host->base)) {
 		dev_err(&pdev->dev, "ioremap failed\n");
-		ret = -ENOMEM;
-		goto error_ioremap;
+		ret = PTR_ERR(host->base);
+		goto fb_release;
 	}
 
 	host->pdev = pdev;
···
 	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);
-		goto error_getpin;
+		goto fb_release;
 	}
 
-	host->clk = clk_get(&host->pdev->dev, NULL);
+	host->clk = devm_clk_get(&host->pdev->dev, NULL);
 	if (IS_ERR(host->clk)) {
 		ret = PTR_ERR(host->clk);
-		goto error_getclock;
+		goto fb_release;
 	}
 
-	panel_enable = of_get_named_gpio_flags(pdev->dev.of_node,
-					       "panel-enable-gpios", 0, &flags);
-	if (gpio_is_valid(panel_enable)) {
-		unsigned long f = GPIOF_OUT_INIT_HIGH;
-		if (flags == OF_GPIO_ACTIVE_LOW)
-			f = GPIOF_OUT_INIT_LOW;
-		ret = devm_gpio_request_one(&pdev->dev, panel_enable,
-					    f, "panel-enable");
-		if (ret) {
-			dev_err(&pdev->dev,
-				"failed to request gpio %d: %d\n",
-				panel_enable, ret);
-			goto error_panel_enable;
-		}
-	}
+	host->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
+	if (IS_ERR(host->reg_lcd))
+		host->reg_lcd = NULL;
 
-	fb_info->pseudo_palette = kmalloc(sizeof(u32) * 16, GFP_KERNEL);
+	fb_info->pseudo_palette = devm_kzalloc(&pdev->dev, sizeof(u32) * 16,
+					       GFP_KERNEL);
 	if (!fb_info->pseudo_palette) {
 		ret = -ENOMEM;
-		goto error_pseudo_pallette;
+		goto fb_release;
 	}
 
 	INIT_LIST_HEAD(&fb_info->modelist);
 
-	host->sync = pdata->sync;
-
 	ret = mxsfb_init_fbinfo(host);
 	if (ret != 0)
-		goto error_init_fb;
-
-	for (i = 0; i < pdata->mode_count; i++)
-		fb_add_videomode(&pdata->mode_list[i], &fb_info->modelist);
+		goto fb_release;
 
 	modelist = list_first_entry(&fb_info->modelist,
 			struct fb_modelist, list);
···
 	ret = register_framebuffer(fb_info);
 	if (ret != 0) {
 		dev_err(&pdev->dev,"Failed to register framebuffer\n");
-		goto error_register;
+		goto fb_destroy;
 	}
 
 	if (!host->enabled) {
···
 
 	return 0;
 
-error_register:
+fb_destroy:
 	if (host->enabled)
 		clk_disable_unprepare(host->clk);
 	fb_destroy_modelist(&fb_info->modelist);
-error_init_fb:
-	kfree(fb_info->pseudo_palette);
-error_pseudo_pallette:
-error_panel_enable:
-	clk_put(host->clk);
-error_getclock:
-error_getpin:
-	iounmap(host->base);
-error_ioremap:
+fb_release:
 	framebuffer_release(fb_info);
-error_alloc_info:
-	release_mem_region(res->start, resource_size(res));
 
 	return ret;
 }
···
 {
 	struct fb_info *fb_info = platform_get_drvdata(pdev);
 	struct mxsfb_info *host = to_imxfb_host(fb_info);
-	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
 	if (host->enabled)
 		mxsfb_disable_controller(fb_info);
 
 	unregister_framebuffer(fb_info);
-	kfree(fb_info->pseudo_palette);
 	mxsfb_free_videomem(host);
-	iounmap(host->base);
-	clk_put(host->clk);
 
 	framebuffer_release(fb_info);
-	release_mem_region(res->start, resource_size(res));
 
 	platform_set_drvdata(pdev, NULL);
 

include/linux/mxsfb.h

···
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __LINUX_MXSFB_H
-#define __LINUX_MXSFB_H
-
-#include <linux/fb.h>
-
-#define STMLCDIF_8BIT 1	/** pixel data bus to the display is of 8 bit width */
-#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
-#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
-#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
-
-#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT	(1 << 6)
-#define MXSFB_SYNC_DOTCLK_FAILING_ACT	(1 << 7) /* failing/negtive edge sampling */
-
-struct mxsfb_platform_data {
-	struct fb_videomode *mode_list;
-	unsigned mode_count;
-
-	unsigned default_bpp;
-
-	unsigned dotclk_delay;	/* refer manual HW_LCDIF_VDCTRL4 register */
-	unsigned ld_intf_width;	/* refer STMLCDIF_* macros */
-
-	unsigned fb_size;	/* Size of the video memory. If zero a
-				 * default will be used
-				 */
-	unsigned long fb_phys;	/* physical address for the video memory. If
-				 * zero the framebuffer memory will be dynamically
-				 * allocated. If specified,fb_size must also be specified.
-				 * fb_phys must be unused by Linux.
-				 */
-	u32 sync;		/* sync mask, contains MXSFB specifics not
-				 * carried in fb_info->var.sync
-				 */
-};
-
-#endif /* __LINUX_MXSFB_H */

include/linux/spi/mxs-spi.h

···
 #ifndef __LINUX_SPI_MXS_SPI_H__
 #define __LINUX_SPI_MXS_SPI_H__
 
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
 
 #define ssp_is_old(host)	((host)->devid == IMX23_SSP)
 
···
 	unsigned int			clk_rate;
 	enum mxs_ssp_id			devid;
 
-	int				dma_channel;
 	struct dma_chan			*dmach;
-	struct mxs_dma_data		dma_data;
 	unsigned int			dma_dir;
 	enum dma_transfer_direction	slave_dirn;
 	u32				ssp_pio_words[SSP_PIO_NUM];