Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt

From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board

* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...

Signed-off-by: Kevin Hilman <[e-mail]>

Documentation/devicetree/bindings/arm/atmel-aic.txt

···
 
 Required properties:
 - compatible: Should be "atmel,<chip>-aic"
+  <chip> can be "at91rm9200" or "sama5d3"
 - interrupt-controller: Identifies the node as an interrupt controller.
 - interrupt-parent: For single AIC system, it is an empty property.
 - #interrupt-cells: The number of cells to define the interrupts. It should be 3.

Documentation/devicetree/bindings/arm/atmel-at91.txt

···
 	};
 
 RAMC SDRAM/DDR Controller required properties:
-- compatible: Should be "atmel,at91sam9260-sdramc",
+- compatible: Should be "atmel,at91rm9200-sdramc",
+			"atmel,at91sam9260-sdramc",
 			"atmel,at91sam9g45-ddramc",
 - reg: Should contain registers location and length
   For at91sam9263 and at91sam9g45 you must specify 2 entries.

arch/arm/boot/dts/Makefile

···
 dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
 # sam9x5
 dtb-$(CONFIG_ARCH_AT91) += at91-ariag25.dtb
+dtb-$(CONFIG_ARCH_AT91) += at91-cosino_mega2560.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb

arch/arm/boot/dts/animeo_ip.dts

···
 			nand-on-flash-bbt;
 			status = "okay";
 
-			at91bootstrap@0 {
-				label = "at91bootstrap";
-				reg = <0x0 0x8000>;
-			};
-
-			barebox@8000 {
+			barebox@0 {
 				label = "barebox";
-				reg = <0x8000 0x40000>;
+				reg = <0x0 0x58000>;
 			};
 
-			bareboxenv@48000 {
-				label = "bareboxenv";
-				reg = <0x48000 0x8000>;
+			u_boot_env@58000 {
+				label = "u_boot_env";
+				reg = <0x58000 0x8000>;
 			};
 
-			user_block@0x50000 {
-				label = "user_block";
-				reg = <0x50000 0xb0000>;
-			};
-
-			kernel@100000 {
-				label = "kernel";
-				reg = <0x100000 0x1b0000>;
-			};
-
-			root@2b0000 {
-				label = "root";
-				reg = <0x2b0000 0x1D50000>;
+			ubi@60000 {
+				label = "ubi";
+				reg = <0x60000 0x1FA0000>;
 			};
 		};
 

arch/arm/boot/dts/at91-cosino.dtsi

···
+/*
+ * at91-cosino.dtsi - Device Tree file for Cosino core module
+ *
+ * Copyright (C) 2013 - Rodolfo Giometti <[e-mail]>
+ *			HCE Engineering
+ *
+ * Derived from at91sam9x5ek.dtsi by:
+ *	Copyright (C) 2012 Atmel,
+ *	2012 Nicolas Ferre <[e-mail]>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "at91sam9g35.dtsi"
+
+/ {
+	model = "HCE Cosino core module";
+	compatible = "hce,cosino", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+					&pinctrl_board_mmc0
+					&pinctrl_mmc0_slot0_clk_cmd_dat0
+					&pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			usart0: serial@f801c000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@f8010000 {
+				status = "okay";
+			};
+
+			adc0: adc@f804c000 {
+				atmel,adc-clock-rate = <1000000>;
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
+				status = "okay";
+			};
+
+			pinctrl@fffff400 {
+				mmc0 {
+					pinctrl_board_mmc0: mmc0-board {
+						atmel,pins =
+							<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PD15 gpio CD pin pull up and deglitch */
+					};
+				};
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;	/* Enable PMECC */
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			uboot@40000 {
+				label = "u-boot";
+				reg = <0x40000 0x80000>;
+			};
+
+			ubootenv@c0000 {
+				label = "U-Boot Env";
+				reg = <0xc0000 0x140000>;
+			};
+
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs@800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/at91-cosino_mega2560.dts

···
+/*
+ * at91-cosino_mega2560.dts - Device Tree file for Cosino board with
+ *			      Mega 2560 extension
+ *
+ * Copyright (C) 2013 - Rodolfo Giometti <[e-mail]>
+ *			HCE Engineering
+ *
+ * Derived from at91sam9g35ek.dts by:
+ * 	Copyright (C) 2012 Atmel,
+ *      2012 Nicolas Ferre <[e-mail]>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+#include "at91-cosino.dtsi"
+
+/ {
+	model = "HCE Cosino Mega 2560";
+	compatible = "hce,cosino_mega2560", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	ahb {
+		apb {
+			macb0: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			adc0: adc@f804c000 {
+				atmel,adc-clock-rate = <1000000>;
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
+				status = "okay";
+			};
+
+
+			tsadcc: tsadcc@f804c000 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+
+			usart1: serial@f8020000 {
+				status = "okay";
+			};
+
+			usart2: serial@f8024000 {
+				status = "okay";
+			};
+
+			usb2: gadget@f803c000 {
+				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
+			mmc1: mmc@f000c000 {
+				pinctrl-0 = <
+					&pinctrl_mmc1_slot0_clk_cmd_dat0
+					&pinctrl_mmc1_slot0_dat1_3>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					non-removable;
+				};
+			};
+		};
+
+		usb0: ohci@00600000 {
+			status = "okay";
+			num-ports = <3>;
+			atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW */
+					   &pioD 19 GPIO_ACTIVE_LOW
+					   &pioD 20 GPIO_ACTIVE_LOW
+					  >;
+		};
+
+		usb1: ehci@00700000 {
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/at91rm9200.dtsi

···
 							 AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA18 periph A */
 					};
 
-					pinctrl_uart0_rts: uart0_rts-0 {
+					pinctrl_uart0_cts: uart0_cts-0 {
 						atmel,pins =
 							<AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA20 periph A */
 					};
 
-					pinctrl_uart0_cts: uart0_cts-0 {
+					pinctrl_uart0_rts: uart0_rts-0 {
 						atmel,pins =
 							<AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA21 periph A */
 					};

arch/arm/boot/dts/at91rm9200ek.dts

···
 
 	ahb {
 		apb {
-			dbgu: serial@fffff200 {
+			usb1: gadget@fffb0000 {
+				atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>;
+				atmel,pullup-gpio = <&pioD 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
+			};
+
+			macb0: ethernet@fffbc000 {
+				phy-mode = "rmii";
+				status = "okay";
+
+				phy0: ethernet-phy {
+					interrupt-parent = <&pioC>;
+					interrupts = <4 IRQ_TYPE_EDGE_BOTH>;
+				};
 			};
 
 			usart1: serial@fffc4000 {
···
 				status = "okay";
 			};
 
-			macb0: ethernet@fffbc000 {
-				phy-mode = "rmii";
-				status = "okay";
-			};
-
-			usb1: gadget@fffb0000 {
-				atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>;
-				status = "okay";
-			};
-
 			spi0: spi@fffe0000 {
 				status = "okay";
 				cs-gpios = <&pioA 3 0>, <0>, <0>, <0>;
···
 					reg = <0>;
 				};
 			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
 		};
 
 		usb0: ohci@00300000 {
 			num-ports = <2>;
 			status = "okay";
+		};
+
+		nor_flash@10000000 {
+			compatible = "cfi-flash";
+			reg = <0x10000000 0x800000>;
+			linux,mtd-name = "physmap-flash.0";
+			bank-width = <2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			barebox@0 {
+				label = "barebox";
+				reg = <0x00000 0x40000>;
+			};
+
+			bareboxenv@40000 {
+				label = "bareboxenv";
+				reg = <0x40000 0x10000>;
+			};
+
+			kernel@50000 {
+				label = "kernel";
+				reg = <0x50000 0x300000>;
+			};
+
+			root@350000  {
+				label = "root";
+				reg = <0x350000 0x4B0000>;
+			};
 		};
 	};
 

arch/arm/boot/dts/at91sam9263.dtsi

···
 					};
 				};
 
+				fb {
+					pinctrl_fb: fb-0 {
+						atmel,pins =
+							<AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC1 periph A */
+							 AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC2 periph A */
+							 AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC3 periph A */
+							 AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PB9 periph B */
+							 AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC6 periph A */
+							 AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC7 periph A */
+							 AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC8 periph A */
+							 AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC9 periph A */
+							 AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC10 periph A */
+							 AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC11 periph A */
+							 AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC14 periph A */
+							 AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC15 periph A */
+							 AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC16 periph A */
+							 AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PC12 periph B */
+							 AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC18 periph A */
+							 AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC19 periph A */
+							 AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC22 periph A */
+							 AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC23 periph A */
+							 AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC24 periph A */
+							 AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PC17 periph B */
+							 AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC26 periph A */
+							 AT91_PIOC 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PC27 periph A */
+					};
+				};
+
 				pioA: gpio@fffff200 {
 					compatible = "atmel,at91rm9200-gpio";
 					reg = <0xfffff200 0x200>;
···
 				pinctrl-0 = <&pinctrl_spi1>;
 				status = "disabled";
 			};
+		};
+
+		fb0: fb@0x00700000 {
+			compatible = "atmel,at91sam9263-lcdc";
+			reg = <0x00700000 0x1000>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fb>;
+			status = "disabled";
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/at91sam9263ek.dts

···
 			};
 		};
 
+		fb0: fb@0x00700000 {
+			display = <&display0>;
+			status = "okay";
+
+			display0: display {
+				bits-per-pixel = <16>;
+				atmel,lcdcon-backlight;
+				atmel,dmacon = <0x1>;
+				atmel,lcdcon2 = <0x80008002>;
+				atmel,guard-time = <1>;
+
+				display-timings {
+					native-mode = <&timing0>;
+					timing0: timing0 {
+						clock-frequency = <4965000>;
+						hactive = <240>;
+						vactive = <320>;
+						hback-porch = <1>;
+						hfront-porch = <33>;
+						vback-porch = <1>;
+						vfront-porch = <0>;
+						hsync-len = <5>;
+						vsync-len = <1>;
+						hsync-active = <1>;
+						vsync-active = <1>;
+					};
+				};
+			};
+		};
+
 		nand0: nand@40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "soft";

arch/arm/boot/dts/at91sam9g45.dtsi

···
 					};
 				};
 
+				i2c0 {
+					pinctrl_i2c0: i2c0-0 {
+						atmel,pins =
+							<AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PA21 periph A TWCK0 */
+							 AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA20 periph A TWD0 */
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1: i2c1-0 {
+						atmel,pins =
+							<AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB11 periph A TWCK1 */
+							 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A TWD1 */
+					};
+				};
+
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
···
 					};
 				};
 
+				fb {
+					pinctrl_fb: fb-0 {
+						atmel,pins =
+							<AT91_PIOE 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE0 periph A */
+							 AT91_PIOE 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE2 periph A */
+							 AT91_PIOE 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE3 periph A */
+							 AT91_PIOE 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE4 periph A */
+							 AT91_PIOE 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE5 periph A */
+							 AT91_PIOE 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE6 periph A */
+							 AT91_PIOE 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE7 periph A */
+							 AT91_PIOE 8 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE8 periph A */
+							 AT91_PIOE 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE9 periph A */
+							 AT91_PIOE 10 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE10 periph A */
+							 AT91_PIOE 11 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE11 periph A */
+							 AT91_PIOE 12 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE12 periph A */
+							 AT91_PIOE 13 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE13 periph A */
+							 AT91_PIOE 14 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE14 periph A */
+							 AT91_PIOE 15 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE15 periph A */
+							 AT91_PIOE 16 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE16 periph A */
+							 AT91_PIOE 17 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE17 periph A */
+							 AT91_PIOE 18 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE18 periph A */
+							 AT91_PIOE 19 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE19 periph A */
+							 AT91_PIOE 20 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE20 periph A */
+							 AT91_PIOE 21 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE21 periph A */
+							 AT91_PIOE 22 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE22 periph A */
+							 AT91_PIOE 23 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE23 periph A */
+							 AT91_PIOE 24 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE24 periph A */
+							 AT91_PIOE 25 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE25 periph A */
+							 AT91_PIOE 26 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE26 periph A */
+							 AT91_PIOE 27 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE27 periph A */
+							 AT91_PIOE 28 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE28 periph A */
+							 AT91_PIOE 29 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PE29 periph A */
+							 AT91_PIOE 30 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PE30 periph A */
+					};
+				};
+
 				pioA: gpio@fffff200 {
 					compatible = "atmel,at91rm9200-gpio";
 					reg = <0xfffff200 0x200>;
···
 				compatible = "atmel,at91sam9g10-i2c";
 				reg = <0xfff84000 0x100>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
···
 				compatible = "atmel,at91sam9g10-i2c";
 				reg = <0xfff88000 0x100>;
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
···
 				compatible = "atmel,hsmci";
 				reg = <0xfff80000 0x600>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
+				pinctrl-names = "default";
 				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
 				dma-names = "rxtx";
 				#address-cells = <1>;
···
 				compatible = "atmel,hsmci";
 				reg = <0xfffd0000 0x600>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>;
+				pinctrl-names = "default";
 				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(13)>;
 				dma-names = "rxtx";
 				#address-cells = <1>;
···
 					atmel,can-isoc;
 				};
 			};
+		};
+
+		fb0: fb@0x00500000 {
+			compatible = "atmel,at91sam9g45-lcdc";
+			reg = <0x00500000 0x1000>;
+			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fb>;
+			status = "disabled";
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/at91sam9m10g45ek.dts

···
 			};
 		};
 
+		fb0: fb@0x00500000 {
+			display = <&display0>;
+			status = "okay";
+
+			display0: display {
+				bits-per-pixel = <32>;
+				atmel,lcdcon-backlight;
+				atmel,dmacon = <0x1>;
+				atmel,lcdcon2 = <0x80008002>;
+				atmel,guard-time = <9>;
+				atmel,lcd-wiring-mode = "RGB";
+
+				display-timings {
+					native-mode = <&timing0>;
+					timing0: timing0 {
+						clock-frequency = <9000000>;
+						hactive = <480>;
+						vactive = <272>;
+						hback-porch = <1>;
+						hfront-porch = <1>;
+						vback-porch = <40>;
+						vfront-porch = <1>;
+						hsync-len = <45>;
+						vsync-len = <1>;
+					};
+				};
+			};
+		};
+
 		nand0: nand@40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "soft";

arch/arm/boot/dts/sama5d3.dtsi

···
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(11)>,
 				       <&dma1 2 AT91_DMA_CFG_PER_ID(12)>;
 				dma-names = "tx", "rx";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&twi2_clk>;
···
 			};
 
 			sha@f8034000 {
-				compatible = "atmel,sam9g46-sha";
+				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf8034000 0x100>;
 				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(17)>;
+				dma-names = "tx";
 			};
 
 			aes@f8038000 {
-				compatible = "atmel,sam9g46-aes";
+				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf8038000 0x100>;
-				interrupts = <43 4 0>;
+				interrupts = <43 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(18)>,
+				       <&dma1 2 AT91_DMA_CFG_PER_ID(19)>;
+				dma-names = "tx", "rx";
 			};
 
 			tdes@f803c000 {
-				compatible = "atmel,sam9g46-tdes";
+				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xf803c000 0x100>;
 				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(20)>,
+				       <&dma1 2 AT91_DMA_CFG_PER_ID(21)>;
+				dma-names = "tx", "rx";
 			};
 
 			dma0: dma-controller@ffffe600 {
···
 						atmel,pins =
 							<AT91_PIOC 26 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PC26 periph B TWD1 pin, conflicts with SPI1_NPCS1, ISI_D11 */
 							 AT91_PIOC 27 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC27 periph B TWCK1 pin, conflicts with SPI1_NPCS2, ISI_D10 */
+					};
+				};
+
+				i2c2 {
+					pinctrl_i2c2: i2c2-0 {
+						atmel,pins =
+							<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE	/* TWD2 pin, conflicts with LCDDAT18, ISI_D2 */
+							 AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TWCK2 pin, conflicts with LCDDAT19, ISI_D3 */
 					};
 				};
 

arch/arm/boot/dts/sama5d3_uart.dtsi

···
 #include <dt-bindings/clk/at91.h>
 
 / {
+	aliases {
+		serial5 = &uart0;
+		serial6 = &uart1;
+	};
+
 	ahb {
 		apb {
 			pinctrl@fffff200 {

arch/arm/boot/dts/sama5d3xdm.dtsi

···
 					interrupts = <31 0x0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_qt1070_irq>;
+					wakeup-source;
 				};
 			};