ARM: dts: imx6ull-colibri: add touchscreen device nodes

Move all Atmel nodes from the board-level into the main module-level
device tree and prepare the device trees for use with Atmel MXT device
tree overlays. Also, add required pinmux groups.

The common scheme for pin groups in touch screen overlays is as follows:
- pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST signals (default)
- pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals.

Signed-off-by: Denys Drozdov <[e-mail]>
Signed-off-by: Marcel Ziswiler <[e-mail]>
Signed-off-by: Shawn Guo <[e-mail]>

arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi

···
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6 &pinctrl_gpio7>;
+		&pinctrl_gpio4 &pinctrl_gpio6 &pinctrl_gpio7>;
 };
 
 &iomuxc_snvs {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2 &pinctrl_snvs_gpio3>;
+	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
 };

arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi

···
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio7>;
+		&pinctrl_gpio4 &pinctrl_gpio7>;
 
 };
 
 &iomuxc_snvs {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2>;
+	pinctrl-0 = <&pinctrl_snvs_gpio1>;
 };
 
 &usdhc2 {

arch/arm/boot/dts/imx6ull-colibri.dtsi

···
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
 	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;       /* SODIMM 107 / INT */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;    /* SODIMM 106 / RST */
+		status = "disabled";
+	};
 };
 
 &i2c2 {
···
 		>;
 	};
 
+	pinctrl_atmel_adap: atmeladapgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16          0xb0a0  /* SODIMM 28 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05       0xb0a0  /* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_atmel_conn: atmelconngrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10          0xb0a0  /* SODIMM 106 */
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04     0xb0a0	/* SODIMM 107 */
+		>;
+	};
+
 	pinctrl_can_int: canint-grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x13010	/* SODIMM 73 */
···
 	pinctrl_gpio4: gpio4-grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x10b0 /* SODIMM 65 */
-		>;
-	};
-
-	pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0xb0a0 /* SODIMM 106 */
 		>;
 	};
 
···
 			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
 			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 */
 			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
-		>;
-	};
-
-	pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0xb0a0	/* SODIMM 107 */
 		>;
 	};