[PATCH] dvb: flexcop: add big endian register definitions

Add big-endian register definitions for running on a PowerPC.
(Thanks to Paavo Hartikainen for testing.)

Signed-off-by: Patrick Boettcher <[e-mail]>
Signed-off-by: Johannes Stezenbach <[e-mail]>
Signed-off-by: Andrew Morton <[e-mail]>
Signed-off-by: Linus Torvalds <[e-mail]>

drivers/media/dvb/b2c2/flexcop-reg.h

···
 extern const char *flexcop_device_names[];
 
 /* FlexCop IBI Registers */
+#if defined(__LITTLE_ENDIAN)
+	#include "flexcop_ibi_value_le.h"
+#elif defined(__BIG_ENDIAN)
+	#include "flexcop_ibi_value_be.h"
+#else
+	#error no endian defined
+#endif
 
-/* flexcop_ibi_reg - a huge union representing the register structure */
-typedef union {
-	u32 raw;
-
-/* DMA 0x000 to 0x01c
- * DMA1 0x000 to 0x00c
- * DMA2 0x010 to 0x01c
- */
-	struct {
-		u32 dma_0start        : 1;   /* set: data will be delivered to dma1_address0 */
-        u32 dma_0No_update    : 1;   /* set: dma1_cur_address will be updated, unset: no update */
-        u32 dma_address0      :30;   /* physical/virtual host memory address0 DMA */
-	} dma_0x0;
-
-	struct {
-		u32 DMA_maxpackets    : 8;   /* (remapped) PCI DMA1 Packet Count Interrupt. This variable
-										is able to be read and written while bit(1) of register
-										0x00c (remap_enable) is set. This variable represents
-										the number of packets that will be transmitted to the PCI
-										host using PCI DMA1 before an interrupt to the PCI is
-										asserted. This functionality may be enabled using bit(20)
-										of register 0x208. N=0 disables the IRQ. */
-		u32 dma_addr_size     :24;   /* size of memory buffer in DWORDs (bytesize / 4) for DMA */
-	} dma_0x4_remap;
-
-	struct {
-		u32 dma1timer         : 7;   /* reading PCI DMA1 timer ... when remap_enable is 0 */
-		u32 unused            : 1;
-		u32 dma_addr_size     :24;
-	} dma_0x4_read;
-
-	struct {
-		u32 unused            : 1;
-		u32 dmatimer          : 7;   /* writing PCI DMA1 timer ... when remap_enable is 0 */
-		u32 dma_addr_size     :24;
-	} dma_0x4_write;
-
-	struct {
-		u32 unused            : 2;
-		u32 dma_cur_addr      :30;   /* current physical host memory address pointer for DMA */
-	} dma_0x8;
-
-	struct {
-		u32 dma_1start        : 1;   /* set: data will be delivered to dma_address1, when dma_address0 is full */
-		u32 remap_enable      : 1;   /* remap enable for 0x0x4(7:0) */
-		u32 dma_address1      :30;   /* Physical/virtual address 1 on DMA */
-	} dma_0xc;
-
-/* Two-wire Serial Master and Clock 0x100-0x110 */
-	struct {
-//		u32 slave_transmitter : 1;   /* ???*/
-		u32 chipaddr          : 7;   /* two-line serial address of the target slave */
-		u32 reserved1         : 1;
-		u32 baseaddr          : 8;   /* address of the location of the read/write operation */
-		u32 data1_reg         : 8;   /* first byte in two-line serial read/write operation */
-		u32 working_start     : 1;  /* when doing a write operation this indicator is 0 when ready
-									  * set to 1 when doing a write operation */
-		u32 twoWS_rw          : 1;   /* read/write indicator (1 = read, 0 write) */
-		u32 total_bytes       : 2;   /* number of data bytes in each two-line serial transaction (0 = 1 byte, 11 = 4byte)*/
-		u32 twoWS_port_reg    : 2;   /* port selection: 01 - Front End/Demod, 10 - EEPROM, 11 - Tuner */
-		u32 no_base_addr_ack_error : 1;   /* writing: write-req: frame is produced w/o baseaddr, read-req: read-cycles w/o
-									  * preceding address assignment write frame
-									  * ACK_ERROR = 1 when no ACK from slave in the last transaction */
-		u32 st_done           : 1;   /* indicator for transaction is done */
-	} tw_sm_c_100;
-
-	struct {
-		u32 data2_reg         : 8;   /* 2nd data byte */
-		u32 data3_reg         : 8;   /* 3rd data byte */
-		u32 data4_reg         : 8;   /* 4th data byte */
-		u32 exlicit_stops     : 1;   /* when set, transactions are produced w/o trailing STOP flag, then send isolated STOP flags */
-		u32 force_stop        : 1;   /* isolated stop flag */
-		u32 unused            : 6;
-	} tw_sm_c_104;
-
-/* Clock. The register allows the FCIII to convert an incoming Master clock
- * (MCLK) signal into a lower frequency clock through the use of a LowCounter
- * (TLO) and a High- Counter (THI). The time counts for THI and TLO are
- * measured in MCLK; each count represents 4 MCLK input clock cycles.
- *
- * The default output for port #1 is set for Front End Demod communication. (0x108)
- * The default output for port #2 is set for EEPROM communication. (0x10c)
- * The default output for port #3 is set for Tuner communication. (0x110)
- */
-	struct {
-		u32 thi1              : 6;   /* Thi for port #1 (def: 100110b; 38) */
-		u32 reserved1         : 2;
-		u32 tlo1              : 5;   /* Tlo for port #1 (def: 11100b; 28) */
-		u32 reserved2         :19;
-	} tw_sm_c_108;
-
-	struct {
-		u32 thi1              : 6;   /* Thi for port #2 (def: 111001b; 57) */
-		u32 reserved1         : 2;
-		u32 tlo1              : 5;   /* Tlo for port #2 (def: 11100b; 28) */
-		u32 reserved2         :19;
-	} tw_sm_c_10c;
-
-	struct {
-		u32 thi1              : 6;   /* Thi for port #3 (def: 111001b; 57) */
-		u32 reserved1         : 2;
-		u32 tlo1              : 5;   /* Tlo for port #3 (def: 11100b; 28) */
-		u32 reserved2         :19;
-	} tw_sm_c_110;
-
-/* LNB Switch Frequency 0x200
- * Clock that creates the LNB switch tone. The default is set to have a fixed
- * low output (not oscillating) to the LNB_CTL line.
- */
-	struct {
-		u32 LNB_CTLHighCount_sig :15; /* It is the number of pre-scaled clock cycles that will be low. */
-		u32 LNB_CTLLowCount_sig  :15; /* For example, to obtain a 22KHz output given a 45 Mhz Master
-										Clock signal (MCLK), set PreScalar=01 and LowCounter value to 0x1ff. */
-		u32 LNB_CTLPrescaler_sig : 2; /* pre-scaler divides MCLK: 00 (no division), 01 by 2, 10 by 4, 11 by 12 */
-	} lnb_switch_freq_200;
-
-/* ACPI, Peripheral Reset, LNB Polarity
- * ACPI power conservation mode, LNB polarity selection (low or high voltage),
- * and peripheral reset.
- */
-	struct {
-		u32 ACPI1_sig         : 1;   /* turn of the power of tuner and LNB, not implemented in FCIII */
-		u32 ACPI3_sig         : 1;   /* turn of power of the complete satelite receiver board (except FCIII) */
-		u32 LNB_L_H_sig       : 1;   /* low or high voltage for LNB. (0 = low, 1 = high) */
-		u32 Per_reset_sig     : 1;   /* misc. init reset (default: 1), to reset set to low and back to high */
-		u32 reserved          :20;
-		u32 Rev_N_sig_revision_hi : 4;/* 0xc in case of FCIII */
-		u32 Rev_N_sig_reserved1 : 2;
-		u32 Rev_N_sig_caps    : 1;   /* if 1, FCIII has 32 PID- and MAC-filters and is capable of IP multicast */
-		u32 Rev_N_sig_reserved2 : 1;
-	} misc_204;
-
-/* Control and Status 0x208 to 0x21c */
-/* Gross enable and disable control */
-	struct {
-		u32 Stream1_filter_sig : 1;  /* Stream1 PID filtering */
-		u32 Stream2_filter_sig : 1;  /* Stream2 PID filtering */
-		u32 PCR_filter_sig    : 1;   /* PCR PID filter */
-		u32 PMT_filter_sig    : 1;   /* PMT PID filter */
-
-		u32 EMM_filter_sig    : 1;   /* EMM PID filter */
-		u32 ECM_filter_sig    : 1;   /* ECM PID filter */
-		u32 Null_filter_sig   : 1;   /* Filters null packets, PID=0x1fff. */
-		u32 Mask_filter_sig   : 1;   /* mask PID filter */
-
-		u32 WAN_Enable_sig    : 1;   /* WAN output line through V8 memory space is activated. */
-		u32 WAN_CA_Enable_sig : 1;   /* not in FCIII */
-		u32 CA_Enable_sig     : 1;   /* not in FCIII */
-		u32 SMC_Enable_sig    : 1;   /* CI stream data (CAI) goes directly to the smart card intf (opposed IBI 0x600 or SC-cmd buf). */
-
-		u32 Per_CA_Enable_sig : 1;   /* not in FCIII */
-		u32 Multi2_Enable_sig : 1;   /* ? */
-		u32 MAC_filter_Mode_sig : 1; /* (MAC_filter_enable) Globally enables MAC filters for Net PID filteres. */
-		u32 Rcv_Data_sig      : 1;   /* PID filtering module enable. When this bit is a one, the PID filter will
-										examine and process packets according to all other (individual) PID
-										filtering controls. If it a zero, no packet processing of any kind will
-										take place. All data from the tuner will be thrown away. */
-
-		u32 DMA1_IRQ_Enable_sig : 1; /* When set, a DWORD counter is enabled on PCI DMA1 that asserts the PCI
-									  * interrupt after the specified count for filling the buffer. */
-		u32 DMA1_Timer_Enable_sig : 1; /* When set, a timer is enabled on PCI DMA1 that asserts the PCI interrupt
-											after a specified amount of time. */
-		u32 DMA2_IRQ_Enable_sig : 1;   /* same as DMA1_IRQ_Enable_sig but for DMA2 */
-		u32 DMA2_Timer_Enable_sig : 1;   /* same as DMA1_Timer_Enable_sig but for DMA2 */
-
-		u32 DMA1_Size_IRQ_Enable_sig : 1; /* When set, a packet count detector is enabled on PCI DMA1 that asserts the PCI interrupt. */
-		u32 DMA2_Size_IRQ_Enable_sig : 1; /* When set, a packet	count detector is enabled on PCI DMA2 that asserts the PCI interrupt. */
-		u32 Mailbox_from_V8_Enable_sig: 1; /* When set, writes to the mailbox register produce an interrupt to the
-											PCI host to indicate that mailbox data is available. */
-
-		u32 unused            : 9;
-	} ctrl_208;
-
-/* General status. When a PCI interrupt occurs, this register is read to
- * discover the reason for the interrupt.
- */
-	struct {
-		u32 DMA1_IRQ_Status   : 1;   /* When set(1) the DMA1 counter had generated an IRQ. Read Only. */
-		u32 DMA1_Timer_Status : 1;   /* When set(1) the DMA1 timer had generated an IRQ. Read Only. */
-		u32 DMA2_IRQ_Status   : 1;   /* When set(1) the DMA2 counter had generated an IRQ. Read Only. */
-		u32 DMA2_Timer_Status : 1;   /* When set(1) the DMA2 timer had generated an IRQ. Read Only. */
-		u32 DMA1_Size_IRQ_Status : 1; /* (Read only). This register is read after an interrupt to */
-		u32 DMA2_Size_IRQ_Status : 1; /* find out why we had an IRQ. Reading this register will clear this bit. Packet count*/
-		u32 Mailbox_from_V8_Status_sig: 1; /* Same as above. Reading this register will clear this bit. */
-		u32 Data_receiver_error : 1; /* 1 indicate an error in the receiver Front End (Tuner module) */
-		u32 Continuity_error_flag : 1;   /* 1 indicates a continuity error in the TS stream. */
-		u32 LLC_SNAP_FLAG_set : 1;   /* 1 indicates that the LCC_SNAP_FLAG was set. */
-		u32 Transport_Error   : 1;   /*  When set indicates that an unexpected packet was received. */
-		u32 reserved          :21;
-	} irq_20c;
-
-
-/* Software reset register */
-	struct {
-		u32 reset_blocks      : 8;   /* Enabled when Block_reset_enable = 0xB2 and 0x208 bits 15:8 = 0x00.
-										Each bit location represents a 0x100 block of registers. Writing
-										a one in a bit location resets that block of registers and the logic
-										that it controls. */
-		u32 Block_reset_enable : 8;  /* This variable is set to 0xB2 when the register is written. */
-		u32 Special_controls  :16;   /* Asserts Reset_V8 => 0xC258; Turns on pci encryption => 0xC25A;
-										Turns off pci encryption => 0xC259 Note: pci_encryption default
-										at power-up is ON. */
-	} sw_reset_210;
-
-	struct {
-		u32 vuart_oe_sig      : 1;   /* When clear, the V8 processor has sole control of the serial UART
-										(RS-232 Smart Card interface). When set, the IBI interface
-										defined by register 0x600 controls the serial UART. */
-		u32 v2WS_oe_sig       : 1;   /* When clear, the V8 processor has direct control of the Two-line
-										Serial Master EEPROM target. When set, the Two-line Serial Master
-										EEPROM target interface is controlled by IBI register 0x100. */
-		u32 halt_V8_sig       : 1;   /* When set, contiguous wait states are applied to the V8-space
-										bus masters. Once this signal is cleared, normal V8-space
-										operations resume. */
-		u32 section_pkg_enable_sig: 1; /* When set, this signal enables the front end translation circuitry
-										  to process section packed transport streams. */
-		u32 s2p_sel_sig       : 1;   /* Serial to parallel conversion. When set, polarized transport data
-										within the FlexCop3 front end circuitry is converted from a serial
-										stream into parallel data before downstream processing otherwise
-										interprets the data. */
-		u32 unused1           : 3;
-		u32 polarity_PS_CLK_sig: 1;  /* This signal is used to invert the input polarity of the tranport
-										stream CLOCK signal before any processing occurs on the transport
-										stream within FlexCop3. */
-		u32 polarity_PS_VALID_sig: 1; /* This signal is used to invert the input polarity of the tranport
-										stream VALID signal before any processing occurs on the transport
-										stream within FlexCop3. */
-		u32 polarity_PS_SYNC_sig: 1; /* This signal is used to invert the input polarity of the tranport
-										stream SYNC signal before any processing occurs on the transport
-										stream within FlexCop3. */
-		u32 polarity_PS_ERR_sig: 1;  /* This signal is used to invert the input polarity of the tranport
-										stream ERROR signal before any processing occurs on the transport
-										stream within FlexCop3. */
-		u32 unused2           :20;
-	} misc_214;
-
-/* Mailbox from V8 to host */
-	struct {
-		u32 Mailbox_from_V8   :32;   /* When this register is written by either the V8 processor or by an
-										end host, an interrupt is generated to the PCI host to indicate
-										that mailbox data is available. Reading register 20c will clear
-										the IRQ. */
-	} mbox_v8_to_host_218;
-
-/* Mailbox from host to v8 Mailbox_to_V8
- * Mailbox_to_V8 mailbox storage register
- * used to send messages from PCI to V8. Writing to this register will send an
- * IRQ to the V8. Then it can read the data from here. Reading this register
- * will clear the IRQ. If the V8 is halted and bit 31 of this register is set,
- * then this register is used instead as a direct interface to access the
- * V8space memory.
- */
-	struct {
-		u32 sysramaccess_data : 8;   /* Data byte written or read from the specified address in V8 SysRAM. */
-		u32 sysramaccess_addr :15;   /* 15 bit address used to access V8 Sys-RAM. */
-		u32 unused            : 7;
-		u32 sysramaccess_write: 1;   /* Write flag used to latch data into the V8 SysRAM. */
-		u32 sysramaccess_busmuster: 1; /* Setting this bit when the V8 is halted at 0x214 Bit(2) allows
-										  this IBI register interface to directly drive the V8-space memory. */
-	} mbox_host_to_v8_21c;
-
-
-/* PIDs, Translation Bit, SMC Filter Select 0x300 to 0x31c */
-	struct {
-		u32 Stream1_PID       :13;   /* Primary use is receiving Net data, so these 13 bits normally
-										hold the PID value for the desired network stream. */
-		u32 Stream1_trans     : 1;   /* When set, Net translation will take place for Net data ferried in TS packets. */
-		u32 MAC_Multicast_filter : 1;   /* When clear, multicast MAC filtering is not allowed for Stream1 and PID_n filters. */
-		u32 debug_flag_pid_saved : 1;
-		u32 Stream2_PID       :13;   /* 13 bits for Stream 2 PID filter value. General use. */
-		u32 Stream2_trans     : 1;   /* When set Tables/CAI translation will take place for the data ferried in
-										Stream2_PID TS packets. */
-		u32 debug_flag_write_status00 : 1;
-		u32 debug_fifo_problem : 1;
-	} pid_filter_300;
-
-	struct {
-		u32 PCR_PID           :13;   /* PCR stream PID filter value. Primary use is Program Clock Reference stream filtering. */
-		u32 PCR_trans         : 1;   /* When set, Tables/CAI translation will take place for these packets. */
-		u32 debug_overrun3    : 1;
-		u32 debug_overrun2    : 1;
-		u32 PMT_PID           :13;   /* stream PID filter value. Primary use is Program Management Table segment filtering. */
-		u32 PMT_trans         : 1;   /* When set, Tables/CAI translation will take place for these packets. */
-		u32 reserved          : 2;
-	} pid_filter_304;
-
-	struct {
-		u32 EMM_PID           :13;   /* EMM PID filter value. Primary use is Entitlement Management Messaging for
-										conditional access-related data. */
-		u32 EMM_trans         : 1;   /* When set, Tables/CAI translation will take place for these packets. */
-		u32 EMM_filter_4      : 1;   /* When set will pass only EMM data possessing the same ID code as the
-										first four bytes (32 bits) of the end-user s 6-byte Smart Card ID number Select */
-		u32 EMM_filter_6      : 1;   /* When set will pass only EMM data possessing the same 6-byte code as the end-users
-										complete 6-byte Smart Card ID number. */
-		u32 ECM_PID           :13;   /* ECM PID filter value. Primary use is Entitlement Control Messaging for conditional
-										access-related data. */
-		u32 ECM_trans         : 1;   /* When set, Tables/CAI translation will take place for these packets. */
-		u32 reserved          : 2;
-	} pid_filter_308;
-
-	struct {
-		u32 Group_PID     :13;   /* PID value for group filtering. */
-		u32 Group_trans   : 1;   /* When set, Tables/CAI translation will take place for these packets. */
-		u32 unused1       : 2;
-		u32 Group_mask    :13;   /* Mask value used in logical "and" equation that defines group filtering */
-		u32 unused2       : 3;
-	} pid_filter_30c_ext_ind_0_7;
-
-	struct {
-		u32 net_master_read :17;
-		u32 unused        :15;
-	} pid_filter_30c_ext_ind_1;
-
-	struct {
-		u32 net_master_write :17;
-		u32 unused        :15;
-	} pid_filter_30c_ext_ind_2;
-
-	struct {
-		u32 next_net_master_write :17;
-		u32 unused        :15;
-	} pid_filter_30c_ext_ind_3;
-
-	struct {
-		u32 unused1       : 1;
-		u32 state_write   :10;
-		u32 reserved1     : 6;   /* default: 000100 */
-		u32 stack_read    :10;
-		u32 reserved2     : 5;   /* default: 00100 */
-	} pid_filter_30c_ext_ind_4;
-
-	struct {
-		u32 stack_cnt     :10;
-		u32 unused        :22;
-	} pid_filter_30c_ext_ind_5;
-
-	struct {
-		u32 pid_fsm_save_reg0 : 2;
-		u32 pid_fsm_save_reg1 : 2;
-		u32 pid_fsm_save_reg2 : 2;
-		u32 pid_fsm_save_reg3 : 2;
-		u32 pid_fsm_save_reg4 : 2;
-		u32 pid_fsm_save_reg300 : 2;
-		u32 write_status1 : 2;
-		u32 write_status4 : 2;
-		u32 data_size_reg :12;
-		u32 unused        : 4;
-	} pid_filter_30c_ext_ind_6;
-
-	struct {
-		u32 index_reg         : 5;   /* (Index pointer) Points at an internal PIDn register. A binary code
-										representing one of 32 internal PIDn registers as well as its
-										corresponding internal MAC_lown register. */
-		u32 extra_index_reg   : 3;   /* This vector is used to select between sets of debug signals routed to register 0x30c. */
-		u32 AB_select         : 1;   /* Used in conjunction with 0x31c. read/write to the MAC_highA or MAC_highB register
-										0=MAC_highB register, 1=MAC_highA */
-		u32 pass_alltables    : 1;   /* 1=Net packets are not filtered against the Network Table ID found in register 0x400.
-										All types of networks (DVB, ATSC, ISDB) are passed. */
-		u32 unused            :22;
-	} index_reg_310;
-
-	struct {
-		u32 PID               :13;   /* PID value */
-		u32 PID_trans         : 1;   /* translation will take place for packets filtered */
-		u32 PID_enable_bit    : 1;   /* When set this PID filter is enabled */
-		u32 reserved          :17;
-	} pid_n_reg_314;
-
-	struct {
-		u32 A4_byte           : 8;
-		u32 A5_byte           : 8;
-		u32 A6_byte           : 8;
-		u32 Enable_bit        : 1;   /* enabled (1) or disabled (1) */
-		u32 HighAB_bit        : 1;   /* use MAC_highA (1) or MAC_highB (0) as MSB */
-		u32 reserved          : 6;
-	} mac_low_reg_318;
-
-	struct {
-		u32 A1_byte           : 8;
-		u32 A2_byte           : 8;
-		u32 A3_byte           : 8;
-		u32 reserved          : 8;
-	} mac_high_reg_31c;
-
-/* Table, SMCID,MACDestination Filters 0x400 to 0x41c */
-	struct {
-		u32 reserved          :16;
 #define fc_data_Tag_ID_DVB  0x3e
 #define fc_data_Tag_ID_ATSC 0x3f
 #define fc_data_Tag_ID_IDSB 0x8b
-		u32 data_Tag_ID       :16;
-	} data_tag_400;
 
-	struct {
-		u32 Card_IDbyte6      : 8;
-		u32 Card_IDbyte5      : 8;
-		u32 Card_IDbyte4      : 8;
-		u32 Card_IDbyte3      : 8;
-	} card_id_408;
-
-	struct {
-		u32 Card_IDbyte2      : 8;
-		u32 Card_IDbyte1      : 8;
-	} card_id_40c;
-
-	/* holding the unique mac address of the receiver which houses the FlexCopIII */
-	struct {
-		u32 MAC1              : 8;
-		u32 MAC2              : 8;
-		u32 MAC3              : 8;
-		u32 MAC6              : 8;
-	} mac_address_418;
-
-	struct {
-		u32 MAC7              : 8;
-		u32 MAC8              : 8;
-		u32 reserved          : 16;
-	} mac_address_41c;
-
-	struct {
-		u32 transmitter_data_byte : 8;
-		u32 ReceiveDataReady  : 1;
-		u32 ReceiveByteFrameError: 1;
-		u32 txbuffempty       : 1;
-		u32 reserved          :21;
-	} ci_600;
-
-	struct {
-		u32 pi_d              : 8;
-		u32 pi_ha             :20;
-		u32 pi_rw             : 1;
-		u32 pi_component_reg  : 3;
-	} pi_604;
-
-	struct {
-		u32 serialReset       : 1;
-		u32 oncecycle_read    : 1;
-		u32 Timer_Read_req    : 1;
-		u32 Timer_Load_req    : 1;
-		u32 timer_data        : 7;
-		u32 unused            : 1; /* ??? not mentioned in data book */
-		u32 Timer_addr        : 5;
-		u32 reserved          : 3;
-		u32 pcmcia_a_mod_pwr_n : 1;
-		u32 pcmcia_b_mod_pwr_n : 1;
-		u32 config_Done_stat  : 1;
-		u32 config_Init_stat  : 1;
-		u32 config_Prog_n     : 1;
-		u32 config_wr_n       : 1;
-		u32 config_cs_n       : 1;
-		u32 config_cclk       : 1;
-		u32 pi_CiMax_IRQ_n    : 1;
-		u32 pi_timeout_status : 1;
-		u32 pi_wait_n         : 1;
-		u32 pi_busy_n         : 1;
-	} pi_608;
-
-	struct {
-		u32 PID               :13;
-		u32 key_enable        : 1;
 #define fc_key_code_default 0x1
 #define fc_key_code_even    0x2
 #define fc_key_code_odd     0x3
-		u32 key_code          : 2;
-		u32 key_array_col     : 3;
-		u32 key_array_row     : 5;
-		u32 dvb_en            : 1; /* 0=TS bypasses the Descrambler */
-		u32 rw_flag           : 1;
-		u32 reserved          : 6;
-	} dvb_reg_60c;
-
-/* SRAM and Output Destination 0x700 to 0x714 */
-	struct {
-		u32 sram_addr         :15;
-		u32 sram_rw           : 1;   /* 0=write, 1=read */
-		u32 sram_data         : 8;
-		u32 sc_xfer_bit       : 1;
-		u32 reserved1         : 3;
-		u32 oe_pin_reg        : 1;
-		u32 ce_pin_reg        : 1;
-		u32 reserved2         : 1;
-		u32 start_sram_ibi    : 1;
-	} sram_ctrl_reg_700;
-
-	struct {
-		u32 net_addr_read     :16;
-		u32 net_addr_write    :16;
-	} net_buf_reg_704;
-
-	struct {
-		u32 cai_read          :11;
-		u32 reserved1         : 5;
-		u32 cai_write         :11;
-		u32 reserved2         : 6;
-		u32 cai_cnt           : 4;
-	} cai_buf_reg_708;
-
-	struct {
-		u32 cao_read          :11;
-		u32 reserved1         : 5;
-		u32 cap_write         :11;
-		u32 reserved2         : 6;
-		u32 cao_cnt           : 4;
-	} cao_buf_reg_70c;
-
-	struct {
-		u32 media_read        :11;
-		u32 reserved1         : 5;
-		u32 media_write       :11;
-		u32 reserved2         : 6;
-		u32 media_cnt         : 4;
-	} media_buf_reg_710;
-
-	struct {
-		u32 NET_Dest          : 2;
-		u32 CAI_Dest          : 2;
-		u32 CAO_Dest          : 2;
-		u32 MEDIA_Dest        : 2;
-		u32 net_ovflow_error  : 1;
-		u32 media_ovflow_error : 1;
-		u32 cai_ovflow_error  : 1;
-		u32 cao_ovflow_error  : 1;
-		u32 ctrl_usb_wan      : 1;
-		u32 ctrl_sramdma      : 1;
-		u32 ctrl_maximumfill  : 1;
-		u32 reserved          :17;
-	} sram_dest_reg_714;
-
-	struct {
-		u32 net_cnt           :12;
-		u32 reserved1         : 4;
-		u32 net_addr_read     : 1;
-		u32 reserved2         : 3;
-		u32 net_addr_write    : 1;
-		u32 reserved3         :11;
-	} net_buf_reg_718;
-
-	struct {
-		u32 wan_speed_sig     : 2;
-		u32 reserved1         : 6;
-		u32 wan_wait_state    : 8;
-		u32 sram_chip         : 2;
-		u32 sram_memmap       : 2;
-		u32 reserved2         : 4;
-		u32 wan_pkt_frame     : 4;
-		u32 reserved3         : 4;
-	} wan_ctrl_reg_71c;
-} flexcop_ibi_value;
 
 extern flexcop_ibi_value ibi_zero;
 

drivers/media/dvb/b2c2/flexcop_ibi_value_be.h

···
+/* This file is part of linux driver for digital TV devices equipped with B2C2 FlexcopII(b)/III
+ *
+ * register descriptions
+ *
+ * see flexcop.c for copyright information.
+ */
+
+/* This file is automatically generated, do not edit things here. */
+#ifndef __FLEXCOP_IBI_VALUE_INCLUDED__
+#define __FLEXCOP_IBI_VALUE_INCLUDED__
+
+typedef union {
+	u32 raw;
+
+	struct {
+		u32 dma_address0                   :30;
+		u32 dma_0No_update                 : 1;
+		u32 dma_0start                     : 1;
+	} dma_0x0;
+
+	struct {
+		u32 dma_addr_size                  :24;
+		u32 DMA_maxpackets                 : 8;
+	} dma_0x4_remap;
+
+	struct {
+		u32 dma_addr_size                  :24;
+		u32 unused                         : 1;
+		u32 dma1timer                      : 7;
+	} dma_0x4_read;
+
+	struct {
+		u32 dma_addr_size                  :24;
+		u32 dmatimer                       : 7;
+		u32 unused                         : 1;
+	} dma_0x4_write;
+
+	struct {
+		u32 dma_cur_addr                   :30;
+		u32 unused                         : 2;
+	} dma_0x8;
+
+	struct {
+		u32 dma_address1                   :30;
+		u32 remap_enable                   : 1;
+		u32 dma_1start                     : 1;
+	} dma_0xc;
+
+	struct {
+		u32 st_done                        : 1;
+		u32 no_base_addr_ack_error         : 1;
+		u32 twoWS_port_reg                 : 2;
+		u32 total_bytes                    : 2;
+		u32 twoWS_rw                       : 1;
+		u32 working_start                  : 1;
+		u32 data1_reg                      : 8;
+		u32 baseaddr                       : 8;
+		u32 reserved1                      : 1;
+		u32 chipaddr                       : 7;
+	} tw_sm_c_100;
+
+	struct {
+		u32 unused                         : 6;
+		u32 force_stop                     : 1;
+		u32 exlicit_stops                  : 1;
+		u32 data4_reg                      : 8;
+		u32 data3_reg                      : 8;
+		u32 data2_reg                      : 8;
+	} tw_sm_c_104;
+
+	struct {
+		u32 reserved2                      :19;
+		u32 tlo1                           : 5;
+		u32 reserved1                      : 2;
+		u32 thi1                           : 6;
+	} tw_sm_c_108;
+
+	struct {
+		u32 reserved2                      :19;
+		u32 tlo1                           : 5;
+		u32 reserved1                      : 2;
+		u32 thi1                           : 6;
+	} tw_sm_c_10c;
+
+	struct {
+		u32 reserved2                      :19;
+		u32 tlo1                           : 5;
+		u32 reserved1                      : 2;
+		u32 thi1                           : 6;
+	} tw_sm_c_110;
+
+	struct {
+		u32 LNB_CTLPrescaler_sig           : 2;
+		u32 LNB_CTLLowCount_sig            :15;
+		u32 LNB_CTLHighCount_sig           :15;
+	} lnb_switch_freq_200;
+
+	struct {
+		u32 Rev_N_sig_reserved2            : 1;
+		u32 Rev_N_sig_caps                 : 1;
+		u32 Rev_N_sig_reserved1            : 2;
+		u32 Rev_N_sig_revision_hi          : 4;
+		u32 reserved                       :20;
+		u32 Per_reset_sig                  : 1;
+		u32 LNB_L_H_sig                    : 1;
+		u32 ACPI3_sig                      : 1;
+		u32 ACPI1_sig                      : 1;
+	} misc_204;
+
+	struct {
+		u32 unused                         : 9;
+		u32 Mailbox_from_V8_Enable_sig     : 1;
+		u32 DMA2_Size_IRQ_Enable_sig       : 1;
+		u32 DMA1_Size_IRQ_Enable_sig       : 1;
+		u32 DMA2_Timer_Enable_sig          : 1;
+		u32 DMA2_IRQ_Enable_sig            : 1;
+		u32 DMA1_Timer_Enable_sig          : 1;
+		u32 DMA1_IRQ_Enable_sig            : 1;
+		u32 Rcv_Data_sig                   : 1;
+		u32 MAC_filter_Mode_sig            : 1;
+		u32 Multi2_Enable_sig              : 1;
+		u32 Per_CA_Enable_sig              : 1;
+		u32 SMC_Enable_sig                 : 1;
+		u32 CA_Enable_sig                  : 1;
+		u32 WAN_CA_Enable_sig              : 1;
+		u32 WAN_Enable_sig                 : 1;
+		u32 Mask_filter_sig                : 1;
+		u32 Null_filter_sig                : 1;
+		u32 ECM_filter_sig                 : 1;
+		u32 EMM_filter_sig                 : 1;
+		u32 PMT_filter_sig                 : 1;
+		u32 PCR_filter_sig                 : 1;
+		u32 Stream2_filter_sig             : 1;
+		u32 Stream1_filter_sig             : 1;
+	} ctrl_208;
+
+	struct {
+		u32 reserved                       :21;
+		u32 Transport_Error                : 1;
+		u32 LLC_SNAP_FLAG_set              : 1;
+		u32 Continuity_error_flag          : 1;
+		u32 Data_receiver_error            : 1;
+		u32 Mailbox_from_V8_Status_sig     : 1;
+		u32 DMA2_Size_IRQ_Status           : 1;
+		u32 DMA1_Size_IRQ_Status           : 1;
+		u32 DMA2_Timer_Status              : 1;
+		u32 DMA2_IRQ_Status                : 1;
+		u32 DMA1_Timer_Status              : 1;
+		u32 DMA1_IRQ_Status                : 1;
+	} irq_20c;
+
+	struct {
+		u32 Special_controls               :16;
+		u32 Block_reset_enable             : 8;
+		u32 reset_blocks                   : 8;
+	} sw_reset_210;
+
+	struct {
+		u32 unused2                        :20;
+		u32 polarity_PS_ERR_sig            : 1;
+		u32 polarity_PS_SYNC_sig           : 1;
+		u32 polarity_PS_VALID_sig          : 1;
+		u32 polarity_PS_CLK_sig            : 1;
+		u32 unused1                        : 3;
+		u32 s2p_sel_sig                    : 1;
+		u32 section_pkg_enable_sig         : 1;
+		u32 halt_V8_sig                    : 1;
+		u32 v2WS_oe_sig                    : 1;
+		u32 vuart_oe_sig                   : 1;
+	} misc_214;
+
+	struct {
+		u32 Mailbox_from_V8                :32;
+	} mbox_v8_to_host_218;
+
+	struct {
+		u32 sysramaccess_busmuster         : 1;
+		u32 sysramaccess_write             : 1;
+		u32 unused                         : 7;
+		u32 sysramaccess_addr              :15;
+		u32 sysramaccess_data              : 8;
+	} mbox_host_to_v8_21c;
+
+	struct {
+		u32 debug_fifo_problem             : 1;
+		u32 debug_flag_write_status00      : 1;
+		u32 Stream2_trans                  : 1;
+		u32 Stream2_PID                    :13;
+		u32 debug_flag_pid_saved           : 1;
+		u32 MAC_Multicast_filter           : 1;
+		u32 Stream1_trans                  : 1;
+		u32 Stream1_PID                    :13;
+	} pid_filter_300;
+
+	struct {
+		u32 reserved                       : 2;
+		u32 PMT_trans                      : 1;
+		u32 PMT_PID                        :13;
+		u32 debug_overrun2                 : 1;
+		u32 debug_overrun3                 : 1;
+		u32 PCR_trans                      : 1;
+		u32 PCR_PID                        :13;
+	} pid_filter_304;
+
+	struct {
+		u32 reserved                       : 2;
+		u32 ECM_trans                      : 1;
+		u32 ECM_PID                        :13;
+		u32 EMM_filter_6                   : 1;
+		u32 EMM_filter_4                   : 1;
+		u32 EMM_trans                      : 1;
+		u32 EMM_PID                        :13;
+	} pid_filter_308;
+
+	struct {
+		u32 unused2                        : 3;
+		u32 Group_mask                     :13;
+		u32 unused1                        : 2;
+		u32 Group_trans                    : 1;
+		u32 Group_PID                      :13;
+	} pid_filter_30c_ext_ind_0_7;
+
+	struct {
+		u32 unused                         :15;
+		u32 net_master_read                :17;
+	} pid_filter_30c_ext_ind_1;
+
+	struct {
+		u32 unused                         :15;
+		u32 net_master_write               :17;
+	} pid_filter_30c_ext_ind_2;
+
+	struct {
+		u32 unused                         :15;
+		u32 next_net_master_write          :17;
+	} pid_filter_30c_ext_ind_3;
+
+	struct {
+		u32 reserved2                      : 5;
+		u32 stack_read                     :10;
+		u32 reserved1                      : 6;
+		u32 state_write                    :10;
+		u32 unused1                        : 1;
+	} pid_filter_30c_ext_ind_4;
+
+	struct {
+		u32 unused                         :22;
+		u32 stack_cnt                      :10;
+	} pid_filter_30c_ext_ind_5;
+
+	struct {
+		u32 unused                         : 4;
+		u32 data_size_reg                  :12;
+		u32 write_status4                  : 2;
+		u32 write_status1                  : 2;
+		u32 pid_fsm_save_reg300            : 2;
+		u32 pid_fsm_save_reg4              : 2;
+		u32 pid_fsm_save_reg3              : 2;
+		u32 pid_fsm_save_reg2              : 2;
+		u32 pid_fsm_save_reg1              : 2;
+		u32 pid_fsm_save_reg0              : 2;
+	} pid_filter_30c_ext_ind_6;
+
+	struct {
+		u32 unused                         :22;
+		u32 pass_alltables                 : 1;
+		u32 AB_select                      : 1;
+		u32 extra_index_reg                : 3;
+		u32 index_reg                      : 5;
+	} index_reg_310;
+
+	struct {
+		u32 reserved                       :17;
+		u32 PID_enable_bit                 : 1;
+		u32 PID_trans                      : 1;
+		u32 PID                            :13;
+	} pid_n_reg_314;
+
+	struct {
+		u32 reserved                       : 6;
+		u32 HighAB_bit                     : 1;
+		u32 Enable_bit                     : 1;
+		u32 A6_byte                        : 8;
+		u32 A5_byte                        : 8;
+		u32 A4_byte                        : 8;
+	} mac_low_reg_318;
+
+	struct {
+		u32 reserved                       : 8;
+		u32 A3_byte                        : 8;
+		u32 A2_byte                        : 8;
+		u32 A1_byte                        : 8;
+	} mac_high_reg_31c;
+
+	struct {
+		u32 data_Tag_ID                    :16;
+		u32 reserved                       :16;
+	} data_tag_400;
+
+	struct {
+		u32 Card_IDbyte3                   : 8;
+		u32 Card_IDbyte4                   : 8;
+		u32 Card_IDbyte5                   : 8;
+		u32 Card_IDbyte6                   : 8;
+	} card_id_408;
+
+	struct {
+		u32 Card_IDbyte1                   : 8;
+		u32 Card_IDbyte2                   : 8;
+	} card_id_40c;
+
+	struct {
+		u32 MAC6                           : 8;
+		u32 MAC3                           : 8;
+		u32 MAC2                           : 8;
+		u32 MAC1                           : 8;
+	} mac_address_418;
+
+	struct {
+		u32 reserved                       :16;
+		u32 MAC8                           : 8;
+		u32 MAC7                           : 8;
+	} mac_address_41c;
+
+	struct {
+		u32 reserved                       :21;
+		u32 txbuffempty                    : 1;
+		u32 ReceiveByteFrameError          : 1;
+		u32 ReceiveDataReady               : 1;
+		u32 transmitter_data_byte          : 8;
+	} ci_600;
+
+	struct {
+		u32 pi_component_reg               : 3;
+		u32 pi_rw                          : 1;
+		u32 pi_ha                          :20;
+		u32 pi_d                           : 8;
+	} pi_604;
+
+	struct {
+		u32 pi_busy_n                      : 1;
+		u32 pi_wait_n                      : 1;
+		u32 pi_timeout_status              : 1;
+		u32 pi_CiMax_IRQ_n                 : 1;
+		u32 config_cclk                    : 1;
+		u32 config_cs_n                    : 1;
+		u32 config_wr_n                    : 1;
+		u32 config_Prog_n                  : 1;
+		u32 config_Init_stat               : 1;
+		u32 config_Done_stat               : 1;
+		u32 pcmcia_b_mod_pwr_n             : 1;
+		u32 pcmcia_a_mod_pwr_n             : 1;
+		u32 reserved                       : 3;
+		u32 Timer_addr                     : 5;
+		u32 unused                         : 1;
+		u32 timer_data                     : 7;
+		u32 Timer_Load_req                 : 1;
+		u32 Timer_Read_req                 : 1;
+		u32 oncecycle_read                 : 1;
+		u32 serialReset                    : 1;
+	} pi_608;
+
+	struct {
+		u32 reserved                       : 6;
+		u32 rw_flag                        : 1;
+		u32 dvb_en                         : 1;
+		u32 key_array_row                  : 5;
+		u32 key_array_col                  : 3;
+		u32 key_code                       : 2;
+		u32 key_enable                     : 1;
+		u32 PID                            :13;
+	} dvb_reg_60c;
+
+	struct {
+		u32 start_sram_ibi                 : 1;
+		u32 reserved2                      : 1;
+		u32 ce_pin_reg                     : 1;
+		u32 oe_pin_reg                     : 1;
+		u32 reserved1                      : 3;
+		u32 sc_xfer_bit                    : 1;
+		u32 sram_data                      : 8;
+		u32 sram_rw                        : 1;
+		u32 sram_addr                      :15;
+	} sram_ctrl_reg_700;
+
+	struct {
+		u32 net_addr_write                 :16;
+		u32 net_addr_read                  :16;
+	} net_buf_reg_704;
+
+	struct {
+		u32 cai_cnt                        : 4;
+		u32 reserved2                      : 6;
+		u32 cai_write                      :11;
+		u32 reserved1                      : 5;
+		u32 cai_read                       :11;
+	} cai_buf_reg_708;
+
+	struct {
+		u32 cao_cnt                        : 4;
+		u32 reserved2                      : 6;
+		u32 cap_write                      :11;
+		u32 reserved1                      : 5;
+		u32 cao_read                       :11;
+	} cao_buf_reg_70c;
+
+	struct {
+		u32 media_cnt                      : 4;
+		u32 reserved2                      : 6;
+		u32 media_write                    :11;
+		u32 reserved1                      : 5;
+		u32 media_read                     :11;
+	} media_buf_reg_710;
+
+	struct {
+		u32 reserved                       :17;
+		u32 ctrl_maximumfill               : 1;
+		u32 ctrl_sramdma                   : 1;
+		u32 ctrl_usb_wan                   : 1;
+		u32 cao_ovflow_error               : 1;
+		u32 cai_ovflow_error               : 1;
+		u32 media_ovflow_error             : 1;
+		u32 net_ovflow_error               : 1;
+		u32 MEDIA_Dest                     : 2;
+		u32 CAO_Dest                       : 2;
+		u32 CAI_Dest                       : 2;
+		u32 NET_Dest                       : 2;
+	} sram_dest_reg_714;
+
+	struct {
+		u32 reserved3                      :11;
+		u32 net_addr_write                 : 1;
+		u32 reserved2                      : 3;
+		u32 net_addr_read                  : 1;
+		u32 reserved1                      : 4;
+		u32 net_cnt                        :12;
+	} net_buf_reg_718;
+
+	struct {
+		u32 reserved3                      : 4;
+		u32 wan_pkt_frame                  : 4;
+		u32 reserved2                      : 4;
+		u32 sram_memmap                    : 2;
+		u32 sram_chip                      : 2;
+		u32 wan_wait_state                 : 8;
+		u32 reserved1                      : 6;
+		u32 wan_speed_sig                  : 2;
+	} wan_ctrl_reg_71c;
+} flexcop_ibi_value;
+
+#endif

drivers/media/dvb/b2c2/flexcop_ibi_value_le.h

···
+/* This file is part of linux driver for digital TV devices equipped with B2C2 FlexcopII(b)/III
+ *
+ * register descriptions
+ *
+ * see flexcop.c for copyright information.
+ */
+
+/* This file is automatically generated, do not edit things here. */
+#ifndef __FLEXCOP_IBI_VALUE_INCLUDED__
+#define __FLEXCOP_IBI_VALUE_INCLUDED__
+
+typedef union {
+	u32 raw;
+
+	struct {
+		u32 dma_0start                     : 1;
+		u32 dma_0No_update                 : 1;
+		u32 dma_address0                   :30;
+	} dma_0x0;
+
+	struct {
+		u32 DMA_maxpackets                 : 8;
+		u32 dma_addr_size                  :24;
+	} dma_0x4_remap;
+
+	struct {
+		u32 dma1timer                      : 7;
+		u32 unused                         : 1;
+		u32 dma_addr_size                  :24;
+	} dma_0x4_read;
+
+	struct {
+		u32 unused                         : 1;
+		u32 dmatimer                       : 7;
+		u32 dma_addr_size                  :24;
+	} dma_0x4_write;
+
+	struct {
+		u32 unused                         : 2;
+		u32 dma_cur_addr                   :30;
+	} dma_0x8;
+
+	struct {
+		u32 dma_1start                     : 1;
+		u32 remap_enable                   : 1;
+		u32 dma_address1                   :30;
+	} dma_0xc;
+
+	struct {
+		u32 chipaddr                       : 7;
+		u32 reserved1                      : 1;
+		u32 baseaddr                       : 8;
+		u32 data1_reg                      : 8;
+		u32 working_start                  : 1;
+		u32 twoWS_rw                       : 1;
+		u32 total_bytes                    : 2;
+		u32 twoWS_port_reg                 : 2;
+		u32 no_base_addr_ack_error         : 1;
+		u32 st_done                        : 1;
+	} tw_sm_c_100;
+
+	struct {
+		u32 data2_reg                      : 8;
+		u32 data3_reg                      : 8;
+		u32 data4_reg                      : 8;
+		u32 exlicit_stops                  : 1;
+		u32 force_stop                     : 1;
+		u32 unused                         : 6;
+	} tw_sm_c_104;
+
+	struct {
+		u32 thi1                           : 6;
+		u32 reserved1                      : 2;
+		u32 tlo1                           : 5;
+		u32 reserved2                      :19;
+	} tw_sm_c_108;
+
+	struct {
+		u32 thi1                           : 6;
+		u32 reserved1                      : 2;
+		u32 tlo1                           : 5;
+		u32 reserved2                      :19;
+	} tw_sm_c_10c;
+
+	struct {
+		u32 thi1                           : 6;
+		u32 reserved1                      : 2;
+		u32 tlo1                           : 5;
+		u32 reserved2                      :19;
+	} tw_sm_c_110;
+
+	struct {
+		u32 LNB_CTLHighCount_sig           :15;
+		u32 LNB_CTLLowCount_sig            :15;
+		u32 LNB_CTLPrescaler_sig           : 2;
+	} lnb_switch_freq_200;
+
+	struct {
+		u32 ACPI1_sig                      : 1;
+		u32 ACPI3_sig                      : 1;
+		u32 LNB_L_H_sig                    : 1;
+		u32 Per_reset_sig                  : 1;
+		u32 reserved                       :20;
+		u32 Rev_N_sig_revision_hi          : 4;
+		u32 Rev_N_sig_reserved1            : 2;
+		u32 Rev_N_sig_caps                 : 1;
+		u32 Rev_N_sig_reserved2            : 1;
+	} misc_204;
+
+	struct {
+		u32 Stream1_filter_sig             : 1;
+		u32 Stream2_filter_sig             : 1;
+		u32 PCR_filter_sig                 : 1;
+		u32 PMT_filter_sig                 : 1;
+		u32 EMM_filter_sig                 : 1;
+		u32 ECM_filter_sig                 : 1;
+		u32 Null_filter_sig                : 1;
+		u32 Mask_filter_sig                : 1;
+		u32 WAN_Enable_sig                 : 1;
+		u32 WAN_CA_Enable_sig              : 1;
+		u32 CA_Enable_sig                  : 1;
+		u32 SMC_Enable_sig                 : 1;
+		u32 Per_CA_Enable_sig              : 1;
+		u32 Multi2_Enable_sig              : 1;
+		u32 MAC_filter_Mode_sig            : 1;
+		u32 Rcv_Data_sig                   : 1;
+		u32 DMA1_IRQ_Enable_sig            : 1;
+		u32 DMA1_Timer_Enable_sig          : 1;
+		u32 DMA2_IRQ_Enable_sig            : 1;
+		u32 DMA2_Timer_Enable_sig          : 1;
+		u32 DMA1_Size_IRQ_Enable_sig       : 1;
+		u32 DMA2_Size_IRQ_Enable_sig       : 1;
+		u32 Mailbox_from_V8_Enable_sig     : 1;
+		u32 unused                         : 9;
+	} ctrl_208;
+
+	struct {
+		u32 DMA1_IRQ_Status                : 1;
+		u32 DMA1_Timer_Status              : 1;
+		u32 DMA2_IRQ_Status                : 1;
+		u32 DMA2_Timer_Status              : 1;
+		u32 DMA1_Size_IRQ_Status           : 1;
+		u32 DMA2_Size_IRQ_Status           : 1;
+		u32 Mailbox_from_V8_Status_sig     : 1;
+		u32 Data_receiver_error            : 1;
+		u32 Continuity_error_flag          : 1;
+		u32 LLC_SNAP_FLAG_set              : 1;
+		u32 Transport_Error                : 1;
+		u32 reserved                       :21;
+	} irq_20c;
+
+	struct {
+		u32 reset_blocks                   : 8;
+		u32 Block_reset_enable             : 8;
+		u32 Special_controls               :16;
+	} sw_reset_210;
+
+	struct {
+		u32 vuart_oe_sig                   : 1;
+		u32 v2WS_oe_sig                    : 1;
+		u32 halt_V8_sig                    : 1;
+		u32 section_pkg_enable_sig         : 1;
+		u32 s2p_sel_sig                    : 1;
+		u32 unused1                        : 3;
+		u32 polarity_PS_CLK_sig            : 1;
+		u32 polarity_PS_VALID_sig          : 1;
+		u32 polarity_PS_SYNC_sig           : 1;
+		u32 polarity_PS_ERR_sig            : 1;
+		u32 unused2                        :20;
+	} misc_214;
+
+	struct {
+		u32 Mailbox_from_V8                :32;
+	} mbox_v8_to_host_218;
+
+	struct {
+		u32 sysramaccess_data              : 8;
+		u32 sysramaccess_addr              :15;
+		u32 unused                         : 7;
+		u32 sysramaccess_write             : 1;
+		u32 sysramaccess_busmuster         : 1;
+	} mbox_host_to_v8_21c;
+
+	struct {
+		u32 Stream1_PID                    :13;
+		u32 Stream1_trans                  : 1;
+		u32 MAC_Multicast_filter           : 1;
+		u32 debug_flag_pid_saved           : 1;
+		u32 Stream2_PID                    :13;
+		u32 Stream2_trans                  : 1;
+		u32 debug_flag_write_status00      : 1;
+		u32 debug_fifo_problem             : 1;
+	} pid_filter_300;
+
+	struct {
+		u32 PCR_PID                        :13;
+		u32 PCR_trans                      : 1;
+		u32 debug_overrun3                 : 1;
+		u32 debug_overrun2                 : 1;
+		u32 PMT_PID                        :13;
+		u32 PMT_trans                      : 1;
+		u32 reserved                       : 2;
+	} pid_filter_304;
+
+	struct {
+		u32 EMM_PID                        :13;
+		u32 EMM_trans                      : 1;
+		u32 EMM_filter_4                   : 1;
+		u32 EMM_filter_6                   : 1;
+		u32 ECM_PID                        :13;
+		u32 ECM_trans                      : 1;
+		u32 reserved                       : 2;
+	} pid_filter_308;
+
+	struct {
+		u32 Group_PID                      :13;
+		u32 Group_trans                    : 1;
+		u32 unused1                        : 2;
+		u32 Group_mask                     :13;
+		u32 unused2                        : 3;
+	} pid_filter_30c_ext_ind_0_7;
+
+	struct {
+		u32 net_master_read                :17;
+		u32 unused                         :15;
+	} pid_filter_30c_ext_ind_1;
+
+	struct {
+		u32 net_master_write               :17;
+		u32 unused                         :15;
+	} pid_filter_30c_ext_ind_2;
+
+	struct {
+		u32 next_net_master_write          :17;
+		u32 unused                         :15;
+	} pid_filter_30c_ext_ind_3;
+
+	struct {
+		u32 unused1                        : 1;
+		u32 state_write                    :10;
+		u32 reserved1                      : 6;
+		u32 stack_read                     :10;
+		u32 reserved2                      : 5;
+	} pid_filter_30c_ext_ind_4;
+
+	struct {
+		u32 stack_cnt                      :10;
+		u32 unused                         :22;
+	} pid_filter_30c_ext_ind_5;
+
+	struct {
+		u32 pid_fsm_save_reg0              : 2;
+		u32 pid_fsm_save_reg1              : 2;
+		u32 pid_fsm_save_reg2              : 2;
+		u32 pid_fsm_save_reg3              : 2;
+		u32 pid_fsm_save_reg4              : 2;
+		u32 pid_fsm_save_reg300            : 2;
+		u32 write_status1                  : 2;
+		u32 write_status4                  : 2;
+		u32 data_size_reg                  :12;
+		u32 unused                         : 4;
+	} pid_filter_30c_ext_ind_6;
+
+	struct {
+		u32 index_reg                      : 5;
+		u32 extra_index_reg                : 3;
+		u32 AB_select                      : 1;
+		u32 pass_alltables                 : 1;
+		u32 unused                         :22;
+	} index_reg_310;
+
+	struct {
+		u32 PID                            :13;
+		u32 PID_trans                      : 1;
+		u32 PID_enable_bit                 : 1;
+		u32 reserved                       :17;
+	} pid_n_reg_314;
+
+	struct {
+		u32 A4_byte                        : 8;
+		u32 A5_byte                        : 8;
+		u32 A6_byte                        : 8;
+		u32 Enable_bit                     : 1;
+		u32 HighAB_bit                     : 1;
+		u32 reserved                       : 6;
+	} mac_low_reg_318;
+
+	struct {
+		u32 A1_byte                        : 8;
+		u32 A2_byte                        : 8;
+		u32 A3_byte                        : 8;
+		u32 reserved                       : 8;
+	} mac_high_reg_31c;
+
+	struct {
+		u32 reserved                       :16;
+		u32 data_Tag_ID                    :16;
+	} data_tag_400;
+
+	struct {
+		u32 Card_IDbyte6                   : 8;
+		u32 Card_IDbyte5                   : 8;
+		u32 Card_IDbyte4                   : 8;
+		u32 Card_IDbyte3                   : 8;
+	} card_id_408;
+
+	struct {
+		u32 Card_IDbyte2                   : 8;
+		u32 Card_IDbyte1                   : 8;
+	} card_id_40c;
+
+	struct {
+		u32 MAC1                           : 8;
+		u32 MAC2                           : 8;
+		u32 MAC3                           : 8;
+		u32 MAC6                           : 8;
+	} mac_address_418;
+
+	struct {
+		u32 MAC7                           : 8;
+		u32 MAC8                           : 8;
+		u32 reserved                       :16;
+	} mac_address_41c;
+
+	struct {
+		u32 transmitter_data_byte          : 8;
+		u32 ReceiveDataReady               : 1;
+		u32 ReceiveByteFrameError          : 1;
+		u32 txbuffempty                    : 1;
+		u32 reserved                       :21;
+	} ci_600;
+
+	struct {
+		u32 pi_d                           : 8;
+		u32 pi_ha                          :20;
+		u32 pi_rw                          : 1;
+		u32 pi_component_reg               : 3;
+	} pi_604;
+
+	struct {
+		u32 serialReset                    : 1;
+		u32 oncecycle_read                 : 1;
+		u32 Timer_Read_req                 : 1;
+		u32 Timer_Load_req                 : 1;
+		u32 timer_data                     : 7;
+		u32 unused                         : 1;
+		u32 Timer_addr                     : 5;
+		u32 reserved                       : 3;
+		u32 pcmcia_a_mod_pwr_n             : 1;
+		u32 pcmcia_b_mod_pwr_n             : 1;
+		u32 config_Done_stat               : 1;
+		u32 config_Init_stat               : 1;
+		u32 config_Prog_n                  : 1;
+		u32 config_wr_n                    : 1;
+		u32 config_cs_n                    : 1;
+		u32 config_cclk                    : 1;
+		u32 pi_CiMax_IRQ_n                 : 1;
+		u32 pi_timeout_status              : 1;
+		u32 pi_wait_n                      : 1;
+		u32 pi_busy_n                      : 1;
+	} pi_608;
+
+	struct {
+		u32 PID                            :13;
+		u32 key_enable                     : 1;
+		u32 key_code                       : 2;
+		u32 key_array_col                  : 3;
+		u32 key_array_row                  : 5;
+		u32 dvb_en                         : 1;
+		u32 rw_flag                        : 1;
+		u32 reserved                       : 6;
+	} dvb_reg_60c;
+
+	struct {
+		u32 sram_addr                      :15;
+		u32 sram_rw                        : 1;
+		u32 sram_data                      : 8;
+		u32 sc_xfer_bit                    : 1;
+		u32 reserved1                      : 3;
+		u32 oe_pin_reg                     : 1;
+		u32 ce_pin_reg                     : 1;
+		u32 reserved2                      : 1;
+		u32 start_sram_ibi                 : 1;
+	} sram_ctrl_reg_700;
+
+	struct {
+		u32 net_addr_read                  :16;
+		u32 net_addr_write                 :16;
+	} net_buf_reg_704;
+
+	struct {
+		u32 cai_read                       :11;
+		u32 reserved1                      : 5;
+		u32 cai_write                      :11;
+		u32 reserved2                      : 6;
+		u32 cai_cnt                        : 4;
+	} cai_buf_reg_708;
+
+	struct {
+		u32 cao_read                       :11;
+		u32 reserved1                      : 5;
+		u32 cap_write                      :11;
+		u32 reserved2                      : 6;
+		u32 cao_cnt                        : 4;
+	} cao_buf_reg_70c;
+
+	struct {
+		u32 media_read                     :11;
+		u32 reserved1                      : 5;
+		u32 media_write                    :11;
+		u32 reserved2                      : 6;
+		u32 media_cnt                      : 4;
+	} media_buf_reg_710;
+
+	struct {
+		u32 NET_Dest                       : 2;
+		u32 CAI_Dest                       : 2;
+		u32 CAO_Dest                       : 2;
+		u32 MEDIA_Dest                     : 2;
+		u32 net_ovflow_error               : 1;
+		u32 media_ovflow_error             : 1;
+		u32 cai_ovflow_error               : 1;
+		u32 cao_ovflow_error               : 1;
+		u32 ctrl_usb_wan                   : 1;
+		u32 ctrl_sramdma                   : 1;
+		u32 ctrl_maximumfill               : 1;
+		u32 reserved                       :17;
+	} sram_dest_reg_714;
+
+	struct {
+		u32 net_cnt                        :12;
+		u32 reserved1                      : 4;
+		u32 net_addr_read                  : 1;
+		u32 reserved2                      : 3;
+		u32 net_addr_write                 : 1;
+		u32 reserved3                      :11;
+	} net_buf_reg_718;
+
+	struct {
+		u32 wan_speed_sig                  : 2;
+		u32 reserved1                      : 6;
+		u32 wan_wait_state                 : 8;
+		u32 sram_chip                      : 2;
+		u32 sram_memmap                    : 2;
+		u32 reserved2                      : 4;
+		u32 wan_pkt_frame                  : 4;
+		u32 reserved3                      : 4;
+	} wan_ctrl_reg_71c;
+} flexcop_ibi_value;
+
+#endif