Merge tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.15

- Switches support for the Draak and Ebisu development boards,
- I2C support on RZ/G2L,
- I2C EEPROM support on the Ebisu development board,
- Sound support for the R-Car D3 SoC and the Draak development board,
- Support for the new R-Car H3e-2G and M3e-2G SoCs on the Salvator-XS
and ULCB development boards,
- IOMMU support for DMAC, EtherAVB, and SDHI on the R-Car M3-W+ SoC,
- Miscellaneous fixes and improvements.

* tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (29 commits)
arm64: dts: renesas: r8a77961: Add iommus to ipmmu_ds[01] related nodes
arm64: dts: renesas: Add support for M3ULCB+Kingfisher with R-Car M3e-2G
arm64: dts: renesas: Add support for M3ULCB with R-Car M3e-2G
arm64: dts: renesas: Add support for Salvator-XS with R-Car M3e-2G
arm64: dts: renesas: Add support for H3ULCB+Kingfisher with R-Car H3e-2G
arm64: dts: renesas: Add support for H3ULCB with R-Car H3e-2G
arm64: dts: renesas: Add support for Salvator-XS with R-Car H3e-2G
arm64: dts: renesas: Add Renesas R8A779M3 SoC support
arm64: dts: renesas: Add Renesas R8A779M1 SoC support
arm64: dts: renesas: hihope-rzg2-ex: Add EtherAVB internal rx delay
arm64: dts: renesas: r8a77995: draak: Add R-Car Sound support
arm64: dts: renesas: r8a77995: Add R-Car Sound support
arm64: dts: renesas: rcar-gen3: Add SoC model to comment headers
arm64: dts: renesas: r8a77990: ebisu: Add I2C EEPROM for PMIC
arm64: dts: renesas: r8a77995: draak: Remove bogus adv7511w properties
arm64: dts: renesas: beacon: Enable micbias
arm64: dts: renesas: r9a07g044: Add I2C nodes
arm64: dts: renesas: r8a779a0: Restore sort order
arm64: dts: renesas: r8a77990: ebisu: Add SW4 support
arm64: dts: renesas: r8a77995: draak: Add SW56 support
...

Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Arnd Bergmann <[e-mail]>

arch/arm/boot/dts/r8a73a4.dtsi

···
 		power-domains = <&pd_a3bc>;
 	};
 
-	dmac: dma-multiplexer {
-		compatible = "renesas,shdma-mux";
-		#dma-cells = <1>;
-		dma-channels = <20>;
-		dma-requests = <256>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		dma0: dma-controller@e6700020 {
-			compatible = "renesas,shdma-r8a73a4";
-			reg = <0 0xe6700020 0 0x89e0>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "error",
-					"ch0", "ch1", "ch2", "ch3",
-					"ch4", "ch5", "ch6", "ch7",
-					"ch8", "ch9", "ch10", "ch11",
-					"ch12", "ch13", "ch14", "ch15",
-					"ch16", "ch17", "ch18", "ch19";
-			clocks = <&mstp2_clks R8A73A4_CLK_DMAC>;
-			power-domains = <&pd_a3sp>;
-		};
-	};
-
 	i2c5: i2c@e60b0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm/boot/dts/r8a7742.dtsi

···
 		iic3: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a7742";
+			compatible = "renesas,iic-r8a7742",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
 			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;

arch/arm/boot/dts/r8a7743.dtsi

···
 			/* doesn't need pinmux */
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a7743";
+			compatible = "renesas,iic-r8a7743",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
 			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;

arch/arm/boot/dts/r8a7744.dtsi

···
 			/* doesn't need pinmux */
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a7744";
+			compatible = "renesas,iic-r8a7744",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
 			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;

arch/arm64/boot/dts/renesas/Makefile

···
 
 dtb-$(CONFIG_ARCH_R8A779A0) += r8a779a0-falcon.dtb
 
+dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-salvator-xs.dtb
+dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-ulcb.dtb
+dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-ulcb-kf.dtb
+
+dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-salvator-xs.dtb
+dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb.dtb
+dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb-kf.dtb
+
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc.dtb

arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi

···
 		compatible = "audio-graph-card";
 		label = "rcar-sound";
 		dais = <&rsnd_port0>, <&rsnd_port1>;
+		widgets = "Microphone", "Mic Jack",
+			  "Line", "Line In Jack",
+			  "Headphone", "Headphone Jack";
+		mic-det-gpio = <&gpio0 2 GPIO_ACTIVE_LOW>;
+		routing = "Headphone Jack", "HPOUTL",
+			 "Headphone Jack", "HPOUTR",
+			 "IN3R", "MICBIAS",
+			 "Mic Jack", "IN3R";
 	};
 
 	vccq_sdhi0: regulator-vccq-sdhi0 {

arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi

···
 	pinctrl-names = "default";
 	phy-handle = <&phy0>;
 	tx-internal-delay-ps = <2000>;
+	rx-internal-delay-ps = <1800>;
 	status = "okay";
 
 	phy0: ethernet-phy@0 {

arch/arm64/boot/dts/renesas/r8a774a1.dtsi

···
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
+		i2c7 = &iic_pmic;
 	};
 
 	/*
···
 			status = "disabled";
 		};
 
-		i2c_dvfs: i2c@e60b0000 {
+		iic_pmic: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "renesas,iic-r8a774a1",

arch/arm64/boot/dts/renesas/r8a774b1.dtsi

···
 			status = "disabled";
 		};
 
-		i2c_dvfs: i2c@e60b0000 {
+		iic_pmic: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "renesas,iic-r8a774b1",

arch/arm64/boot/dts/renesas/r8a774c0.dtsi

···
 			status = "disabled";
 		};
 
-		i2c_dvfs: i2c@e60b0000 {
+		iic_pmic: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a774c0";
-			reg = <0 0xe60b0000 0 0x15>;
+			compatible = "renesas,iic-r8a774c0",
+				     "renesas,rcar-gen3-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;

arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts

···
 	clock-names = "du.0", "du.1", "du.2", "du.3",
 		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
 };
-
-&ehci2 {
-	status = "okay";
-};
-
-&hdmi1 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi1_out: endpoint {
-				remote-endpoint = <&hdmi1_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-			dw_hdmi1_snd_in: endpoint {
-				remote-endpoint = <&rsnd_endpoint2>;
-			};
-		};
-	};
-};
-
-&hdmi1_con {
-	remote-endpoint = <&rcar_dw_hdmi1_out>;
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&pfc {
-	usb2_pins: usb2 {
-		groups = "usb2";
-		function = "usb2";
-	};
-};
-
-&rcar_sound {
-	ports {
-		/* rsnd_port0/1 are described in salvator-common.dtsi */
-		rsnd_port2: port@2 {
-			reg = <2>;
-			rsnd_endpoint2: endpoint {
-				remote-endpoint = <&dw_hdmi1_snd_in>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_endpoint2>;
-				frame-master = <&rsnd_endpoint2>;
-
-				playback = <&ssi3>;
-			};
-		};
-	};
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_card {
-	dais = <&rsnd_port0	/* ak4613 */
-		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2>;	/* HDMI1  */
-};
-
-&usb2_phy2 {
-	pinctrl-0 = <&usb2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};

arch/arm64/boot/dts/renesas/r8a77950-ulcb-kf.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the H3ULCB Kingfisher board
+ * Device Tree Source for the H3ULCB Kingfisher board with R-Car H3 ES1.x
  *
  * Copyright (C) 2017 Renesas Electronics Corp.
  * Copyright (C) 2017 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77950-ulcb.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board
+ * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board with R-Car H3 ES1.x
  *
  * Copyright (C) 2016 Renesas Electronics Corp.
  * Copyright (C) 2016 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77950.dtsi

···
 
 #include "r8a77951.dtsi"
 
+#undef SOC_HAS_USB2_CH3
+
 &audma0 {
 	iommus = <&ipmmu_mp1 0>, <&ipmmu_mp1 1>,
 	       <&ipmmu_mp1 2>, <&ipmmu_mp1 3>,

arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts

···
 	clock-names = "du.0", "du.1", "du.2", "du.3",
 		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
 };
-
-&ehci2 {
-	status = "okay";
-};
-
-&hdmi1 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi1_out: endpoint {
-				remote-endpoint = <&hdmi1_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-			dw_hdmi1_snd_in: endpoint {
-				remote-endpoint = <&rsnd_endpoint2>;
-			};
-		};
-	};
-};
-
-&hdmi1_con {
-	remote-endpoint = <&rcar_dw_hdmi1_out>;
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&pfc {
-	usb2_pins: usb2 {
-		groups = "usb2";
-		function = "usb2";
-	};
-};
-
-&rcar_sound {
-	ports {
-		/* rsnd_port0/1 are described in salvator-common.dtsi */
-		rsnd_port2: port@2 {
-			reg = <2>;
-			rsnd_endpoint2: endpoint {
-				remote-endpoint = <&dw_hdmi1_snd_in>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_endpoint2>;
-				frame-master = <&rsnd_endpoint2>;
-
-				playback = <&ssi3>;
-			};
-		};
-	};
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_card {
-	dais = <&rsnd_port0	/* ak4613 */
-		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2>;	/* HDMI1  */
-};
-
-&usb2_phy2 {
-	pinctrl-0 = <&usb2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};

arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts

···
 	clock-names = "du.0", "du.1", "du.2", "du.3",
 		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
 };
-
-&ehci2 {
-	status = "okay";
-};
-
-&ehci3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&hdmi1 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi1_out: endpoint {
-				remote-endpoint = <&hdmi1_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-			dw_hdmi1_snd_in: endpoint {
-				remote-endpoint = <&rsnd_endpoint2>;
-			};
-		};
-	};
-};
-
-&hdmi1_con {
-	remote-endpoint = <&rcar_dw_hdmi1_out>;
-};
-
-&hsusb3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&ohci3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&pca9654 {
-	pcie-sata-switch-hog {
-		gpio-hog;
-		gpios = <7 GPIO_ACTIVE_HIGH>;
-		output-low; /* enable SATA by default */
-		line-name = "PCIE/SATA switch";
-	};
-};
-
-&pfc {
-	usb2_pins: usb2 {
-		groups = "usb2";
-		function = "usb2";
-	};
-
-	/*
-	 * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
-	 *   (when SW31 is the default setting on Salvator-XS).
-	 * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
-	 *   r8a77951 with Salvator-XS.
-	 *   Hence the SW31 setting must be changed like 2) below.
-	 *   1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
-	 *	- Connect GP6_3[01] to ADV7842.
-	 *   2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
-	 *	- Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
-	 *	- Connect GP6_{04,21} to ADV7842.
-	 */
-	usb2_ch3_pins: usb2_ch3 {
-		groups = "usb2_ch3";
-		function = "usb2_ch3";
-	};
-};
-
-&rcar_sound {
-	ports {
-		/* rsnd_port0/1 are described in salvator-common.dtsi */
-		rsnd_port2: port@2 {
-			reg = <2>;
-			rsnd_endpoint2: endpoint {
-				remote-endpoint = <&dw_hdmi1_snd_in>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_endpoint2>;
-				frame-master = <&rsnd_endpoint2>;
-
-				playback = <&ssi3>;
-			};
-		};
-	};
-};
-
-/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
-&sata {
-	status = "okay";
-};
-
-&sound_card {
-	dais = <&rsnd_port0	/* ak4613 */
-		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2>;	/* HDMI1  */
-};
-
-&usb2_phy2 {
-	pinctrl-0 = <&usb2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&usb2_phy3 {
-	pinctrl-0 = <&usb2_ch3_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};

arch/arm64/boot/dts/renesas/r8a77951-ulcb-kf.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the H3ULCB Kingfisher board
+ * Device Tree Source for the H3ULCB Kingfisher board with R-Car H3 ES2.0+
  *
  * Copyright (C) 2017 Renesas Electronics Corp.
  * Copyright (C) 2017 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77951-ulcb.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board
+ * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board with R-Car H3 ES2.0+
  *
  * Copyright (C) 2016 Renesas Electronics Corp.
  * Copyright (C) 2016 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77951.dtsi

···
 
 #define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
+#define SOC_HAS_HDMI1
+#define SOC_HAS_SATA
+#define SOC_HAS_USB2_CH2
+#define SOC_HAS_USB2_CH3
+
 / {
 	compatible = "renesas,r8a7795";
 	#address-cells = <2>;

arch/arm64/boot/dts/renesas/r8a77960-ulcb-kf.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3ULCB Kingfisher board
+ * Device Tree Source for the M3ULCB Kingfisher board with R-Car M3-W
  *
  * Copyright (C) 2017 Renesas Electronics Corp.
  * Copyright (C) 2017 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77960-ulcb.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) board
+ * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) board with R-Car M3-W
  *
  * Copyright (C) 2016 Renesas Electronics Corp.
  * Copyright (C) 2016 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77961-ulcb-kf.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3ULCB Kingfisher board
+ * Device Tree Source for the M3ULCB Kingfisher board with R-Car M3-W+
  *
  * Copyright (C) 2020 Eugeniu Rosca <[e-mail]>
  */

arch/arm64/boot/dts/renesas/r8a77961-ulcb.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) board with R-Car
- * M3-W+
+ * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) board with R-Car M3-W+
  *
  * Copyright (C) 2020 Renesas Electronics Corp.
  */

arch/arm64/boot/dts/renesas/r8a77961.dtsi

···
 			resets = <&cpg 219>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds0 0>, <&ipmmu_ds0 1>,
+			       <&ipmmu_ds0 2>, <&ipmmu_ds0 3>,
+			       <&ipmmu_ds0 4>, <&ipmmu_ds0 5>,
+			       <&ipmmu_ds0 6>, <&ipmmu_ds0 7>,
+			       <&ipmmu_ds0 8>, <&ipmmu_ds0 9>,
+			       <&ipmmu_ds0 10>, <&ipmmu_ds0 11>,
+			       <&ipmmu_ds0 12>, <&ipmmu_ds0 13>,
+			       <&ipmmu_ds0 14>, <&ipmmu_ds0 15>;
 		};
 
 		dmac1: dma-controller@e7300000 {
···
 			resets = <&cpg 218>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 0>, <&ipmmu_ds1 1>,
+			       <&ipmmu_ds1 2>, <&ipmmu_ds1 3>,
+			       <&ipmmu_ds1 4>, <&ipmmu_ds1 5>,
+			       <&ipmmu_ds1 6>, <&ipmmu_ds1 7>,
+			       <&ipmmu_ds1 8>, <&ipmmu_ds1 9>,
+			       <&ipmmu_ds1 10>, <&ipmmu_ds1 11>,
+			       <&ipmmu_ds1 12>, <&ipmmu_ds1 13>,
+			       <&ipmmu_ds1 14>, <&ipmmu_ds1 15>;
 		};
 
 		dmac2: dma-controller@e7310000 {
···
 			resets = <&cpg 217>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 16>, <&ipmmu_ds1 17>,
+			       <&ipmmu_ds1 18>, <&ipmmu_ds1 19>,
+			       <&ipmmu_ds1 20>, <&ipmmu_ds1 21>,
+			       <&ipmmu_ds1 22>, <&ipmmu_ds1 23>,
+			       <&ipmmu_ds1 24>, <&ipmmu_ds1 25>,
+			       <&ipmmu_ds1 26>, <&ipmmu_ds1 27>,
+			       <&ipmmu_ds1 28>, <&ipmmu_ds1 29>,
+			       <&ipmmu_ds1 30>, <&ipmmu_ds1 31>;
 		};
 
 		ipmmu_ds0: iommu@e6740000 {
···
 			phy-mode = "rgmii";
 			rx-internal-delay-ps = <0>;
 			tx-internal-delay-ps = <0>;
+			iommus = <&ipmmu_ds0 16>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
···
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
+			iommus = <&ipmmu_ds1 32>;
 			status = "disabled";
 		};
 
···
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
+			iommus = <&ipmmu_ds1 33>;
 			status = "disabled";
 		};
 
···
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
+			iommus = <&ipmmu_ds1 34>;
 			status = "disabled";
 		};
 
···
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
+			iommus = <&ipmmu_ds1 35>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts

···
 	clock-names = "du.0", "du.1", "du.3",
 		      "dclkin.0", "dclkin.1", "dclkin.3";
 };
-
-&pca9654 {
-	pcie-sata-switch-hog {
-		gpio-hog;
-		gpios = <7 GPIO_ACTIVE_HIGH>;
-		output-low; /* enable SATA by default */
-		line-name = "PCIE/SATA switch";
-	};
-};
-
-/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
-&sata {
-	status = "okay";
-};

arch/arm64/boot/dts/renesas/r8a77965-ulcb-kf.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3NULCB Kingfisher board
+ * Device Tree Source for the M3NULCB Kingfisher board with R-Car M3-N
  *
  * Copyright (C) 2018 Renesas Electronics Corp.
  * Copyright (C) 2018 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77965-ulcb.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the M3NULCB (R-Car Starter Kit Pro) board
+ * Device Tree Source for the M3NULCB (R-Car Starter Kit Pro) board with R-Car M3-N
  *
  * Copyright (C) 2018 Renesas Electronics Corp.
  * Copyright (C) 2018 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77965.dtsi

···
 
 #define CPG_AUDIO_CLK_I		R8A77965_CLK_S0D4
 
+#define SOC_HAS_SATA
+
 / {
 	compatible = "renesas,r8a77965";
 	#address-cells = <2>;

arch/arm64/boot/dts/renesas/r8a77970-eagle.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the Eagle board
+ * Device Tree Source for the Eagle board with R-Car V3M
  *
  * Copyright (C) 2016-2017 Renesas Electronics Corp.
  * Copyright (C) 2017 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77980-condor.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the Condor board
+ * Device Tree Source for the Condor board with R-Car V3H
  *
  * Copyright (C) 2018 Renesas Electronics Corp.
  * Copyright (C) 2018 Cogent Embedded, Inc.

arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the ebisu board
+ * Device Tree Source for the Ebisu board with R-Car E3
  *
  * Copyright (C) 2018 Renesas Electronics Corp.
  */
···
 /dts-v1/;
 #include "r8a77990.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Renesas Ebisu board based on r8a77990";
···
 			hdmi_con_out: endpoint {
 				remote-endpoint = <&adv7511_out>;
 			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW4-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW4-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW4-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW4-4";
+			wakeup-source;
+			debounce-interval = <20>;
 		};
 	};
 
···
 		rohm,ddr-backup-power = <0x1>;
 		rohm,rstbmode-level;
 	};
+
+	eeprom@50 {
+		compatible = "rohm,br24t01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
 };
 
 &lvds0 {
···
 	irq0_pins: irq0 {
 		groups = "intc_ex_irq0";
 		function = "intc_ex";
+	};
+
+	keys_pins: keys {
+		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
+		bias-pull-up;
 	};
 
 	pwm3_pins: pwm3 {

arch/arm64/boot/dts/renesas/r8a77990.dtsi

···
 		i2c_dvfs: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a77990";
-			reg = <0 0xe60b0000 0 0x15>;
+			compatible = "renesas,iic-r8a77990",
+				     "renesas,rcar-gen3-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;

arch/arm64/boot/dts/renesas/r8a77995-draak.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the Draak board
+ * Device Tree Source for the Draak board with R-Car D3
  *
  * Copyright (C) 2016-2018 Renesas Electronics Corp.
  * Copyright (C) 2017 Glider bvba
···
 /dts-v1/;
 #include "r8a77995.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Renesas Draak board based on r8a77995";
···
 	aliases {
 		serial0 = &scif2;
 		ethernet0 = &avb;
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
 	};
 
 	backlight: backlight {
···
 			hdmi_con_out: endpoint {
 				remote-endpoint = <&adv7511_out>;
 			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW56-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW56-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW56-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW56-4";
+			wakeup-source;
+			debounce-interval = <20>;
 		};
 	};
 
···
 		regulator-always-on;
 	};
 
+	sound_card: sound {
+		compatible = "audio-graph-card";
+
+		dais = <&rsnd_port0	/* ak4613 */
+			/* HDMI is not yet supported */
+		>;
+	};
+
 	vga {
 		compatible = "vga-connector";
 
···
 		#clock-cells = <0>;
 		clock-frequency = <74250000>;
 	};
+
+	x19_clk: x19 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&audio_clk_b {
+	/*
+	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
+	 * and R-Car Sound uses AUDIO_CLKB.
+	 * Note is that schematic indicates VI4_FIELD conection only
+	 * not AUDIO_CLKB at SoC page.
+	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
+	 * SW60 should be 1-2.
+	 */
+
+	clock-frequency = <22579200>;
 };
 
 &avb {
···
 	pinctrl-names = "default";
 	status = "okay";
 
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 0>; /* audio_clkout */
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+
+		port {
+			ak4613_endpoint: endpoint {
+				remote-endpoint = <&rsnd_for_ak4613>;
+			};
+		};
+	};
+
 	composite-in@20 {
 		compatible = "adi,adv7180cp";
 		reg = <0x20>;
···
 		reg-names = "main", "edid", "cec", "packet";
 		interrupt-parent = <&gpio1>;
 		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
-
-		/* Depends on LVDS */
-		max-clock = <135000000>;
-		min-vrefresh = <50>;
 
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
···
 				};
 			};
 		};
+	};
+
+	cs2000: clk-multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
 	};
 
 	eeprom@50 {
···
 		function = "i2c1";
 	};
 
+	keys_pins: keys {
+		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
+		bias-pull-up;
+	};
+
 	pwm0_pins: pwm0 {
 		groups = "pwm0_c";
 		function = "pwm0";
···
 		power-source = <1800>;
 	};
 
+	sound_pins: sound {
+		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound-clk {
+		groups = "audio_clk_a", "audio_clk_b",
+			 "audio_clkout", "audio_clkout1";
+		function = "audio_clk";
+	};
+
 	usb0_pins: usb0 {
 		groups = "usb0";
 		function = "usb0";
···
 	pinctrl-names = "default";
 
 	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1 */
+	#clock-cells = <1>;
+	clock-frequency = <12288000 11289600>;
+
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
+		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&cs2000>, <&audio_clk_b>,
+		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
+
+	ports {
+		rsnd_port0: port {
+			rsnd_for_ak4613: endpoint {
+				remote-endpoint = <&ak4613_endpoint>;
+				dai-format = "left_j";
+				bitclock-master = <&rsnd_for_ak4613>;
+				frame-master = <&rsnd_for_ak4613>;
+				playback = <&ssi3>, <&src5>, <&dvc0>;
+				capture  = <&ssi4>, <&src6>, <&dvc1>;
+			};
+		};
+	};
 };
 
 &rwdt {
···
 	no-sdio;
 	non-removable;
 	status = "okay";
+};
+
+&ssi4 {
+	shared-pin;
 };
 
 &usb2_phy0 {

arch/arm64/boot/dts/renesas/r8a77995.dtsi

···
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	/*
+	 * The external audio clocks are configured as 0 Hz fixed frequency
+	 * clocks by default.
+	 * Boards that provide audio clocks should override them.
+	 */
+	audio_clk_a: audio_clk_a {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_b: audio_clk_b {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
···
 			resets = <&cpg 807>;
 			renesas,id = <4>;
 			status = "disabled";
+		};
+
+		rcar_sound: sound@ec500000 {
+			/*
+			 * #sound-dai-cells is required
+			 *
+			 * Single DAI : #sound-dai-cells = <0>;	<&rcar_sound>;
+			 * Multi  DAI : #sound-dai-cells = <1>;	<&rcar_sound N>;
+			 */
+			/*
+			 * #clock-cells is required for audio_clkout0/1/2/3
+			 *
+			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
+			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
+			 */
+			compatible =  "renesas,rcar_sound-r8a77995", "renesas,rcar_sound-gen3";
+			reg =	<0 0xec500000 0 0x1000>, /* SCU */
+				<0 0xec5a0000 0 0x100>,  /* ADG */
+				<0 0xec540000 0 0x1000>, /* SSIU */
+				<0 0xec541000 0 0x280>,  /* SSI */
+				<0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
+			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
+
+			clocks = <&cpg CPG_MOD 1005>,
+				 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
+				 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+				 <&audio_clk_a>, <&audio_clk_b>,
+				 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
+			clock-names = "ssi-all",
+				      "ssi.4", "ssi.3",
+				      "src.6", "src.5",
+				      "mix.1", "mix.0",
+				      "ctu.1", "ctu.0",
+				      "dvc.0", "dvc.1",
+				      "clk_a", "clk_b", "clk_i";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 1005>,
+				 <&cpg 1011>, <&cpg 1012>;
+			reset-names = "ssi-all",
+				      "ssi.4", "ssi.3";
+			status = "disabled";
+
+			rcar_sound,ctu {
+				ctu00: ctu-0 { };
+				ctu01: ctu-1 { };
+				ctu02: ctu-2 { };
+				ctu03: ctu-3 { };
+				ctu10: ctu-4 { };
+				ctu11: ctu-5 { };
+				ctu12: ctu-6 { };
+				ctu13: ctu-7 { };
+			};
+
+			rcar_sound,dvc {
+				dvc0: dvc-0 {
+					dmas = <&audma0 0xbc>;
+					dma-names = "tx";
+				};
+				dvc1: dvc-1 {
+					dmas = <&audma0 0xbe>;
+					dma-names = "tx";
+				};
+			};
+
+			rcar_sound,mix {
+				mix0: mix-0 { };
+				mix1: mix-1 { };
+			};
+
+			rcar_sound,src {
+				src5: src-5 {
+					interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8f>, <&audma0 0xb2>;
+					dma-names = "rx", "tx";
+				};
+				src6: src-6 {
+					interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x91>, <&audma0 0xb4>;
+					dma-names = "rx", "tx";
+				};
+			};
+
+			rcar_sound,ssi {
+				ssi3: ssi-3 {
+					interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x07>, <&audma0 0x08>,
+					       <&audma0 0x6f>, <&audma0 0x70>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi4: ssi-4 {
+					interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x09>, <&audma0 0x0a>,
+					       <&audma0 0x71>, <&audma0 0x72>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+			};
+		};
+
+		audma0: dma-controller@ec700000 {
+			compatible = "renesas,dmac-r8a77995",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec700000 0 0x10000>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7",
+					"ch8", "ch9", "ch10", "ch11",
+					"ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 502>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 502>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+			iommus = <&ipmmu_mp 0>, <&ipmmu_mp 1>,
+				 <&ipmmu_mp 2>, <&ipmmu_mp 3>,
+				 <&ipmmu_mp 4>, <&ipmmu_mp 5>,
+				 <&ipmmu_mp 6>, <&ipmmu_mp 7>,
+				 <&ipmmu_mp 8>, <&ipmmu_mp 9>,
+				 <&ipmmu_mp 10>, <&ipmmu_mp 11>,
+				 <&ipmmu_mp 12>, <&ipmmu_mp 13>,
+				 <&ipmmu_mp 14>, <&ipmmu_mp 15>;
 		};
 
 		ohci0: usb@ee080000 {

arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts

···
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Device Tree Source for the Falcon CPU and BreakOut boards
+ * Device Tree Source for the Falcon CPU and BreakOut boards with R-Car V3U
  *
  * Copyright (C) 2020 Renesas Electronics Corp.
  */

arch/arm64/boot/dts/renesas/r8a779a0.dtsi

···
 			#power-domain-cells = <1>;
 		};
 
+		tsc: thermal@e6190000 {
+			compatible = "renesas,r8a779a0-thermal";
+			reg = <0 0xe6190000 0 0x200>,
+			      <0 0xe6198000 0 0x200>,
+			      <0 0xe61a0000 0 0x200>,
+			      <0 0xe61a8000 0 0x200>,
+			      <0 0xe61b0000 0 0x200>;
+			clocks = <&cpg CPG_MOD 919>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 919>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		tmu0: timer@e61e0000 {
 			compatible = "renesas,tmu-r8a779a0", "renesas,tmu";
 			reg = <0 0xe61e0000 0 0x30>;
···
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 717>;
 			status = "disabled";
-		};
-
-		tsc: thermal@e6190000 {
-			compatible = "renesas,r8a779a0-thermal";
-			reg = <0 0xe6190000 0 0x200>,
-			      <0 0xe6198000 0 0x200>,
-			      <0 0xe61a0000 0 0x200>,
-			      <0 0xe61a8000 0 0x200>,
-			      <0 0xe61b0000 0 0x200>;
-			clocks = <&cpg CPG_MOD 919>;
-			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets = <&cpg 919>;
-			#thermal-sensor-cells = <1>;
 		};
 
 		i2c0: i2c@e6500000 {

arch/arm64/boot/dts/renesas/r8a779m1-salvator-xs.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car H3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77951-salvator-xs.dts
+ * Copyright (C) 2015-2017 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779m1.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a779m1";
+	compatible = "renesas,salvator-xs", "renesas,r8a779m1",
+		     "renesas,r8a7795";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	memory@500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory@700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 721>,
+		 <&versaclock6 1>,
+		 <&x21_clk>,
+		 <&x22_clk>,
+		 <&versaclock6 2>;
+	clock-names = "du.0", "du.1", "du.2", "du.3",
+		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
+};

arch/arm64/boot/dts/renesas/r8a779m1-ulcb-kf.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the H3ULCB Kingfisher board with R-Car H3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77951-ulcb-kf.dts
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ * Copyright (C) 2017 Cogent Embedded, Inc.
+ */
+
+#include "r8a779m1-ulcb.dts"
+#include "ulcb-kf.dtsi"
+
+/ {
+	model = "Renesas H3ULCB Kingfisher board based on r8a779m1";
+	compatible = "shimafuji,kingfisher", "renesas,h3ulcb",
+		     "renesas,r8a779m1", "renesas,r8a7795";
+};

arch/arm64/boot/dts/renesas/r8a779m1-ulcb.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) with R-Car H3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77951-ulcb.dts
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ */
+
+/dts-v1/;
+#include "r8a779m1.dtsi"
+#include "ulcb.dtsi"
+
+/ {
+	model = "Renesas H3ULCB board based on r8a779m1";
+	compatible = "renesas,h3ulcb", "renesas,r8a779m1", "renesas,r8a7795";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	memory@500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory@700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 721>,
+		 <&versaclock5 1>,
+		 <&versaclock5 3>,
+		 <&versaclock5 4>,
+		 <&versaclock5 2>;
+	clock-names = "du.0", "du.1", "du.2", "du.3",
+		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
+};

arch/arm64/boot/dts/renesas/r8a779m1.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3e-2G (R8A779M1) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m1", "renesas,r8a7795";
+};

arch/arm64/boot/dts/renesas/r8a779m3-salvator-xs.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car M3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77961-salvator-xs.dts
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779m3.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a779m3";
+	compatible = "renesas,salvator-xs", "renesas,r8a779m3",
+		     "renesas,r8a77961";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@480000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x1 0x00000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&versaclock6 1>,
+		 <&x21_clk>,
+		 <&versaclock6 2>;
+	clock-names = "du.0", "du.1", "du.2",
+		      "dclkin.0", "dclkin.1", "dclkin.2";
+};

arch/arm64/boot/dts/renesas/r8a779m3-ulcb-kf.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the M3ULCB Kingfisher board with R-Car M3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77961-ulcb-kf.dts
+ * Copyright (C) 2020 Eugeniu Rosca <[e-mail]>
+ */
+
+#include "r8a779m3-ulcb.dts"
+#include "ulcb-kf.dtsi"
+
+/ {
+	model = "Renesas M3ULCB Kingfisher board based on r8a779m3";
+	compatible = "shimafuji,kingfisher", "renesas,m3ulcb",
+		     "renesas,r8a779m3", "renesas,r8a77961";
+};

arch/arm64/boot/dts/renesas/r8a779m3-ulcb.dts

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) with R-Car M3e-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77961-ulcb.dts
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779m3.dtsi"
+#include "ulcb.dtsi"
+
+/ {
+	model = "Renesas M3ULCB board based on r8a779m3";
+	compatible = "renesas,m3ulcb", "renesas,r8a779m3", "renesas,r8a77961";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@480000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x1 0x00000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&versaclock5 1>,
+		 <&versaclock5 3>,
+		 <&versaclock5 2>;
+	clock-names = "du.0", "du.1", "du.2",
+		      "dclkin.0", "dclkin.1", "dclkin.2";
+};

arch/arm64/boot/dts/renesas/r8a779m3.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3e-2G (R8A779M3) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77961.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m3", "renesas,r8a77961";
+};

arch/arm64/boot/dts/renesas/r9a07g044.dtsi

···
 			status = "disabled";
 		};
 
+		i2c0: i2c@10058000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g044", "renesas,riic-rz";
+			reg = <0 0x10058000 0 0x400>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 348 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 349 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_I2C0_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G044_I2C0_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@10058400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g044", "renesas,riic-rz";
+			reg = <0 0x10058400 0 0x400>;
+			interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 356 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 357 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_I2C1_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G044_I2C1_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@10058800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g044", "renesas,riic-rz";
+			reg = <0 0x10058800 0 0x400>;
+			interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_I2C2_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G044_I2C2_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@10058c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g044", "renesas,riic-rz";
+			reg = <0 0x10058c00 0 0x400>;
+			interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 372 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 373 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_I2C3_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G044_I2C3_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@11010000 {
 			compatible = "renesas,r9a07g044-cpg";
 			reg = <0 0x11010000 0 0x10000>;

arch/arm64/boot/dts/renesas/salvator-common.dtsi

···
 		label = "rcar-sound";
 
 		dais = <&rsnd_port0	/* ak4613 */
-			&rsnd_port1>;	/* HDMI0  */
+			&rsnd_port1	/* HDMI0  */
+#ifdef SOC_HAS_HDMI1
+			&rsnd_port2	/* HDMI1  */
+#endif
+			>;
 	};
 
 	vbus0_usb2: regulator-vbus0-usb2 {
···
 &hdmi0_con {
 	remote-endpoint = <&rcar_dw_hdmi0_out>;
 };
+
+#ifdef SOC_HAS_HDMI1
+&hdmi1 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+			rcar_dw_hdmi1_out: endpoint {
+				remote-endpoint = <&hdmi1_con>;
+			};
+		};
+		port@2 {
+			reg = <2>;
+			dw_hdmi1_snd_in: endpoint {
+				remote-endpoint = <&rsnd_endpoint2>;
+			};
+		};
+	};
+};
+
+&hdmi1_con {
+	remote-endpoint = <&rcar_dw_hdmi1_out>;
+};
+#endif /* SOC_HAS_HDMI1 */
 
 &hscif1 {
 	pinctrl-0 = <&hscif1_pins>;
···
 				playback = <&ssi2>;
 			};
 		};
+
+#ifdef SOC_HAS_HDMI1
+		rsnd_port2: port@2 {
+			reg = <2>;
+			rsnd_endpoint2: endpoint {
+				remote-endpoint = <&dw_hdmi1_snd_in>;
+
+				dai-format = "i2s";
+				bitclock-master = <&rsnd_endpoint2>;
+				frame-master = <&rsnd_endpoint2>;
+
+				playback = <&ssi3>;
+			};
+		};
+#endif /* SOC_HAS_HDMI1 */
 	};
 };
 
···
 	timeout-sec = <60>;
 	status = "okay";
 };
+
+#ifdef SOC_HAS_SATA
+&sata {
+	status = "okay";
+};
+#endif /* SOC_HAS_SATA */
 
 &scif1 {
 	pinctrl-0 = <&scif1_pins>;
···
 
 	status = "okay";
 };
+
+#ifdef SOC_HAS_USB2_CH2
+&ehci2 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&pfc {
+	usb2_pins: usb2 {
+		groups = "usb2";
+		function = "usb2";
+	};
+};
+
+&usb2_phy2 {
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+#endif /* SOC_HAS_USB2_CH2 */

arch/arm64/boot/dts/renesas/salvator-xs.dtsi

···
 		clock-names = "xin";
 	};
 };
+
+#ifdef SOC_HAS_SATA
+&pca9654 {
+	pcie-sata-switch-hog {
+		gpio-hog;
+		gpios = <7 GPIO_ACTIVE_HIGH>;
+		output-low; /* enable SATA by default */
+		line-name = "PCIE/SATA switch";
+	};
+};
+
+/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
+#endif /* SOC_HAS_SATA */
+
+#ifdef SOC_HAS_USB2_CH3
+&ehci3 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&hsusb3 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci3 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&pfc {
+	/*
+	 * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
+	 *   (when SW31 is the default setting on Salvator-XS).
+	 * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
+	 *   r8a77951 with Salvator-XS.
+	 *   Hence the SW31 setting must be changed like 2) below.
+	 *   1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
+	 *	- Connect GP6_3[01] to ADV7842.
+	 *   2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
+	 *	- Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
+	 *	- Connect GP6_{04,21} to ADV7842.
+	 */
+	usb2_ch3_pins: usb2_ch3 {
+		groups = "usb2_ch3";
+		function = "usb2_ch3";
+	};
+};
+
+&usb2_phy3 {
+	pinctrl-0 = <&usb2_ch3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+#endif /* SOC_HAS_USB2_CH3 */