ARM: dts: stm32: add support for Protonic PRTT1x boards

This boards are based on STM32MP151AAD3 and use 10BaseT1L for communication.

- PRTT1C - 10BaseT1L switch
- PRTT1S - 10BaseT1L CO2 sensor board
- PRTT1A - 10BaseT1L multi functional controller

Signed-off-by: Oleksij Rempel <[e-mail]>
Signed-off-by: Alexandre Torgue <[e-mail]>

arch/arm/boot/dts/Makefile

···
 	stm32h743i-disco.dtb \
 	stm32h750i-art-pi.dtb \
 	stm32mp135f-dk.dtb \
+	stm32mp151a-prtt1a.dtb \
+	stm32mp151a-prtt1c.dtb \
+	stm32mp151a-prtt1s.dtb \
 	stm32mp153c-dhcom-drc02.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \

arch/arm/boot/dts/stm32mp151a-prtt1a.dts

···
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <[e-mail]>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1A";
+	compatible = "prt,prtt1a", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
+
+&pwm5_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+	};
+};
+
+&pwm5_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};

arch/arm/boot/dts/stm32mp151a-prtt1c.dts

···
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <[e-mail]>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1C";
+	compatible = "prt,prtt1c", "st,stm32mp151";
+
+	clock_ksz9031: clock-ksz9031 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_sja1105: clock-sja1105 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethernet0 {
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpioa {
+	gpio-line-names =
+		"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
+		"", "", "", "", "", "", "", "SPI1_nSS";
+};
+
+&gpiod {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"WFM_RESET", "", "", "", "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names =
+		"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
+		"", "", "", "", "WFM_nIRQ", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "PHY3_nINT",
+		"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
+		"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
+};
+
+&mdio0 {
+	/* All this DP83TD510E PHYs can't be probed before switch@0 is
+	 * probed so we need to use compatible with PHYid
+	 */
+	/* TI DP83TD510E */
+	t1l0_phy: ethernet-phy@6 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <6>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l1_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <7>;
+		interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l2_phy: ethernet-phy@10 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <10>;
+		interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* Micrel KSZ9031 */
+	rj45_phy: ethernet-phy@2 {
+		reg = <2>;
+		interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <1000>;
+
+		clocks = <&clock_ksz9031>;
+	};
+};
+
+&qspi {
+	status = "disabled";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc2_b4_od_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+	};
+};
+
+&sdmmc2_b4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_b4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+			 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc2_d47_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	non-removable;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mmc@1 {
+		compatible = "prt,prtt1c-wfm200", "silabs,wf200";
+		reg = <1>;
+	};
+};
+
+&sdmmc3_b4_od_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+	};
+};
+
+&sdmmc3_b4_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+	};
+};
+
+&sdmmc3_b4_sleep_pins_b {
+	pins {
+		pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+			 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pins_b>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	switch@0 {
+		compatible = "nxp,sja1105q";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-rx-delay-us = <1>;
+		spi-tx-delay-us = <1>;
+		spi-cpha;
+
+		reset-gpios = <&gpioe 6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clock_sja1105>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "t1l0";
+				phy-mode = "rmii";
+				phy-handle = <&t1l0_phy>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "t1l1";
+				phy-mode = "rmii";
+				phy-handle = <&t1l1_phy>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "t1l2";
+				phy-mode = "rmii";
+				phy-handle = <&t1l2_phy>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "rj45";
+				phy-handle = <&rj45_phy>;
+				phy-mode = "rgmii-id";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "cpu";
+				ethernet = <&ethernet0>;
+				phy-mode = "rmii";
+
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};

arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi

···
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <[e-mail]>
+ */
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxad-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mdio-gpio0 = &mdio0;
+		serial0 = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+	 * stmmac MDC clock without reducing system bus rate, we need to use
+	 * gpio based MDIO bus.
+	 */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>; /* ETH1_RMII_TX_EN */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK input */
+			 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&ethernet0_rmii_sleep_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&iwdg2 {
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&qspi_bk1_pins_a {
+	pins1 {
+		bias-pull-up;
+		drive-push-pull;
+		slew-rate = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_od_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc1_b4_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart4_idle_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* UART4_TX */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+		bias-disable;
+		drive-push-pull;
+		slew-rate = <0>;
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>, /* UART4_TX */
+			<STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+	};
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&reg_3v3>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&reg_3v3>;
+};

arch/arm/boot/dts/stm32mp151a-prtt1s.dts

···
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <[e-mail]>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1S";
+	compatible = "prt,prtt1s", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <100000>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	humidity-sensor@40 {
+		compatible = "ti,hdc1080";
+		reg = <0x40>;
+	};
+
+	co2-sensor@62 {
+		compatible = "sensirion,scd41";
+		reg = <0x62>;
+	};
+};
+
+&i2c1_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+	};
+};
+
+&i2c1_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+	};
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};