Pull SCSI fixes from James Bottomley:
"Four fixes, all in drivers: three fairly obvious small ones and a
large one in aacraid to add block queue completion mapping and fix a
CPU offline hang"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix incorrect big endian type assignment in bsg loopback path
scsi: target: core: Fix error path in target_setup_session()
scsi: storvsc: Always set no_report_opcodes
scsi: aacraid: Reply queue mapping to CPUs based on IRQ affinity

Pull ata fix from Damien Le Moal:

- Avoid deadlocks on resume from sleep by delaying scsi rescan until
the scsi device is also fully resumed.

* tag 'ata-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-scsi: Avoid deadlock on rescan after device resume

The kernel test robot reported sparse warnings regarding incorrect type
assignment for __be16 variables in bsg loopback path.

Change the flagged lines to use the be16_to_cpu() and cpu_to_be16() macros
appropriately.

Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230614175944.3577-1-justintee8345@gmail.com
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306110819.sDIKiGgg-lkp@intel.com/
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull parisc fix from Helge Deller:

- Drop redundant register definitions to fix build with latest binutils

* tag 'parisc-for-6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Delete redundant register definitions in <asm/assembly.h>

When an ATA port is resumed from sleep, the port is reset and a power
management request issued to libata EH to reset the port and rescanning
the device(s) attached to the port. Device rescanning is done by
scheduling an ata_scsi_dev_rescan() work, which will execute
scsi_rescan_device().

However, scsi_rescan_device() takes the generic device lock, which is
also taken by dpm_resume() when the SCSI device is resumed as well. If
a device rescan execution starts before the completion of the SCSI
device resume, the rcu locking used to refresh the cached VPD pages of
the device, combined with the generic device locking from
scsi_rescan_device() and from dpm_resume() can cause a deadlock.

Avoid this situation by changing struct ata_port scsi_rescan_task to be
a delayed work instead of a simple work_struct. ata_scsi_dev_rescan() is
modified to check if the SCSI device associated with the ATA device that
must be rescanned is not suspended. If the SCSI device is still
suspended, ata_scsi_dev_rescan() returns early and reschedule itself for
execution after an arbitrary delay of 5ms.

Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Joe Breuer <linux-kernel@jmbreuer.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217530
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Joe Breuer <linux-kernel@jmbreuer.net>

In the error exits in target_setup_session(), if a branch is taken to
free_sess: transport_free_session() may call to target_free_cmd_counter()
and then fall through to call target_free_cmd_counter() a second time.
This can, and does, sometimes cause seg faults since the data field in
cmd_cnt->refcnt has been freed in the first call.

Fix this problem by simply returning after the call to
transport_free_session(). The second call is redundant for those cases.

Fixes: 4edba7e4a8f3 ("scsi: target: Move cmd counter allocation")
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Link: https://lore.kernel.org/r/20230613144259.12890-1-rpearsonhpe@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The error unrolling was leaving the VMAs detached in many cases and
leaving the locked_vm statistic altered, and skipping the unrolling
entirely in the case of the vma tree write failing.

Fix the error path by re-attaching the detached VMAs and adding the
necessary goto for the failed vma tree write, and fix the locked_vm
statistic by only updating after the vma tree write succeeds.

Fixes: 763ecb035029 ("mm: remove the vma linked list")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We define sp and ipsw in <asm/asmregs.h> using ".reg", and when using
current binutils (snapshot 2.40.50.20230611) the definitions in
<asm/assembly.h> using "=" conflict with those:

arch/parisc/include/asm/assembly.h: Assembler messages:
arch/parisc/include/asm/assembly.h:93: Error: symbol `sp' is already defined
arch/parisc/include/asm/assembly.h:95: Error: symbol `ipsw' is already defined

Delete the duplicate definitions in <asm/assembly.h>.

Also delete the definition of gp, which isn't used anywhere.

Signed-off-by: Ben Hutchings <benh@debian.org>
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Helge Deller <deller@gmx.de>

For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.

However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:

hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type

Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.

Reported-by: Xingui Yang <yangxingui@huawei.com>
Fixes: 41bda9c98035 ("libata-link: update hotplug to handle PMP links")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>

Hyper-V synthetic SCSI devices do not support the MAINTENANCE_IN SCSI
command, so scsi_report_opcode() always fails, resulting in messages like
this:

hv_storvsc <guid>: tag#205 cmd 0xa3 status: scsi 0x2 srb 0x86 hv 0xc0000001

The recently added support for command duration limits calls
scsi_report_opcode() four times as each device comes online, which
significantly increases the number of messages logged in a system with many
disks.

Fix the problem by always marking Hyper-V synthetic SCSI devices as not
supporting scsi_report_opcode(). With this setting, the MAINTENANCE_IN SCSI
command is not issued and no messages are logged.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1686343101-18930-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull staging driver fix from Greg KH:
"Here is a single staging driver "fix" for 6.4-rc7. I've been sitting
on it in my tree for many weeks as it is just a simple documentation
update, with the hope that maybe some other staging driver fixes would
need to be merged for 6.4-final, but that does not seem to be the
case.

So please, pull in this one documentation update so that Aaro doesn't
get emails going forward that he can't do anything about"

* tag 'staging-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon: delete my name from TODO contact

Current only one entry is enabled but IP itself is using 4 different IDs
which are already listed in zynqmp.dtsi.

sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
...
iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
<&smmu 0x4c2>, <&smmu 0x4c3>;
};

Fixes: 8ac47837f0e0 ("arm64: dts: zynqmp: Add missing iommu IDs")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>

Fix the I/O hang that arises because of the MSIx vector not having a mapped
online CPU upon receiving completion.

SCSI cmds take the blk_mq route, which is setup during init. Reserved cmds
fetch the vector_no from mq_map after init is complete. Before init, they
have to use 0 - as per the norm.

Reviewed-by: Gilbert Wu <gilbert.wu@microchip.com>
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20230519230834.27436-1-sagar.biradar@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull USB / Thunderbolt fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes and new device
ids for 6.4-rc7 to resolve some reported problems. Included in here
are:

- new USB serial device ids

- USB gadget core fixes for long-dissussed problems

- dwc3 bugfixes for reported issues.

- typec driver fixes

- thunderbolt driver fixes

All of these have been in linux-next this week with no reported issues"

* tag 'usb-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc: core: Prevent soft_connect_store() race
usb: gadget: udc: core: Offload usb_udc_vbus_handler processing
usb: typec: Fix fast_role_swap_current show function
usb: typec: ucsi: Fix command cancellation
USB: dwc3: fix use-after-free on core driver unbind
USB: dwc3: qcom: fix NULL-deref on suspend
usb: dwc3: gadget: Reset num TRBs before giving back the request
usb: gadget: udc: renesas_usb3: Fix RZ/V2M {modprobe,bind} error
USB: serial: option: add Quectel EM061KGL series
thunderbolt: Mask ring interrupt on Intel hardware as well
thunderbolt: Do not touch CL state configuration during discovery
thunderbolt: Increase DisplayPort Connection Manager handshake timeout
thunderbolt: dma_test: Use correct value for absent rings when creating paths

I gave up using MIPS OCTEON hardware after the drivers were deleted from
staging in 2019. Afterwards, the driver seems to be added back but the TODO
contact name was not updated accordingly. Delete my name, as I still get
mails from people asking help with the driver and their systems.

Fixes: 422d97b8b05e ("Revert "staging: octeon: delete driver"")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230427211606.GD881984@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 fix from Borislav Petkov:

- Set up the kernel CS earlier in the boot process in case EFI boots
the kernel after bypassing the decompressor and the CS descriptor
used ends up being the EFI one which is not mapped in the identity
page table, leading to early SEV/SNP guest communication exceptions
resulting in the guest crashing

* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed

gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:

In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~

See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.

Cc: stable@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull serial driver fixes from Greg KH:
"Here are two small serial driver fixes for 6.4-rc7 that resolve some
reported problems:

- lantiq serial driver irq fix

- fsl_lpuart serial driver watermark fix

Both of these have been in linux-next this week with no reported issues"

* tag 'tty-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: fsl_lpuart: reduce RX watermark to 0 on LS1028A
serial: lantiq: add missing interrupt ack

usb_udc_connect_control(), soft_connect_store() and
usb_gadget_deactivate() can potentially race against each other to invoke
usb_gadget_connect()/usb_gadget_disconnect(). To prevent this, guard
udc->started, gadget->allow_connect, gadget->deactivate and
gadget->connect with connect_lock so that ->pullup() is only invoked when
the gadget is bound, started and not deactivated. The routines
usb_gadget_connect_locked(), usb_gadget_disconnect_locked(),
usb_udc_connect_control_locked(), usb_gadget_udc_start_locked(),
usb_gadget_udc_stop_locked() are called with this lock held.

An earlier version of this commit was reverted due to the crash reported in
https://lore.kernel.org/all/ZF4BvgsOyoKxdPFF@francesco-nb.int.toradex.com/.
commit 16737e78d190 ("usb: gadget: udc: core: Offload usb_udc_vbus_handler processing")
addresses the crash reported.

Cc: stable@vger.kernel.org
Fixes: 628ef0d273a6 ("usb: udc: add usb_udc_vbus_handler")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-2-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:

- Fix four slab out of bounds warnings: improve checks for protocol
id, and for small packet length, and for create context parsing,
and for negotiate context parsing

- Fix for incorrect dereferencing POSIX ACLs"

* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: validate smb request protocol id
ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
ksmbd: fix out-of-bound read in parse_lease_state()
ksmbd: fix out-of-bound read in deassemble_neg_contexts()

The call to startup_64_setup_env() will install a new GDT but does not
actually switch to using the KERNEL_CS entry until returning from the
function call.

Commit bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in
boot") moved the call to sme_enable() earlier in the boot process and in
between the call to startup_64_setup_env() and the switch to KERNEL_CS.
An SEV-ES or an SEV-SNP guest will trigger #VC exceptions during the call
to sme_enable() and if the CS pushed on the stack as part of the exception
and used by IRETQ is not mapped by the new GDT, then problems occur.
Today, the current CS when entering startup_64 is the kernel CS value
because it was set up by the decompressor code, so no issue is seen.

However, a recent patchset that looked to avoid using the legacy
decompressor during an EFI boot exposed this bug. At entry to startup_64,
the CS value is that of EFI and is not mapped in the new kernel GDT. So
when a #VC exception occurs, the CS value used by IRETQ is not valid and
the guest boot crashes.

Fix this issue by moving the block that switches to the KERNEL_CS value to
be done immediately after returning from startup_64_setup_env().

Fixes: bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in boot")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/all/6ff1f28af2829cc9aea357ebee285825f90a431f.1684340801.git.thomas.lendacky%40amd.com

Pull compute express link fixes from Dan Williams:

- Fix a compilation issue with DEFINE_STATIC_SRCU() in the unit tests

- Fix leaking kernel memory to a root-only sysfs attribute

* tag 'cxl-fixes-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl: Add missing return to cdat read error path
tools/testing/cxl: Use DEFINE_STATIC_SRCU()

When target mode is enabled, the pci_irq_get_affinity() function may return
a NULL value in qla_mapq_init_qp_cpu_map() due to the qla24xx_enable_msix()
code that handles IRQ settings for target mode. This leads to a crash due
to a NULL pointer dereference.

This patch fixes the issue by adding a check for the NULL value returned by
pci_irq_get_affinity() and introducing a 'cpu_mapped' boolean flag to the
qla_qpair structure, ensuring that the qpair's CPU affinity is updated when
it has not been mapped to a CPU.

Fixes: 1d201c81d4cc ("scsi: qla2xxx: Select qpair depending on which CPU post_cmd() gets called")
Signed-off-by: Gleb Chesnokov <gleb.chesnokov@scst.dev>
Link: https://lore.kernel.org/r/56b416f2-4e0f-b6cf-d6d5-b7c372e3c6a2@scst.dev
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes:

- Fix an OOB issue in the Mediatek mt8365 driver where arrays of clks
are mismatched in size

- Use the proper clk_ops for a few clks in the Mediatek mt8365 driver

- Stop using abs() in clk_composite_determine_rate() because 64-bit
math goes wrong on large unsigned long numbers that are subtracted
and passed into abs()

- Zero initialize a struct clk_init_data in clk-loongson2 to avoid
stack junk confusing clk_hw_register()

- Actually use a pointer to __iomem for writel() in
pxa3xx_clk_update_accr() so we don't oops"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: pxa: fix NULL pointer dereference in pxa3xx_clk_update_accr
clk: clk-loongson2: Zero init clk_init_data
clk: mediatek: mt8365: Fix inverted topclk operations
clk: composite: Fix handling of high clock rates
clk: mediatek: mt8365: Fix index issue

LS1028A is using DMA with LPUART. Having RX watermark set to 1, means
DMA transactions are started only after receiving the second character.

On other platforms with newer LPUART IP, Receiver Idle Empty function
initiates the DMA request after the receiver is idling for 4 characters.
But this feature is missing on LS1028A, which is causing a 1-character
delay in the RX direction on this platform.

Set RX watermark to 0 to initiate RX DMA after each character.

Link: https://lore.kernel.org/linux-serial/20230607103459.1222426-1-robert.hodaszi@digi.com/
Fixes: 9ad9df844754 ("tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case")
Cc: stable <stable@kernel.org>
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Message-ID: <20230609121334.1878626-1-robert.hodaszi@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_udc_vbus_handler() can be invoked from interrupt context by irq
handlers of the gadget drivers, however, usb_udc_connect_control() has
to run in non-atomic context due to the following:
a. Some of the gadget driver implementations expect the ->pullup
callback to be invoked in non-atomic context.
b. usb_gadget_disconnect() acquires udc_lock which is a mutex.

Hence offload invocation of usb_udc_connect_control()
to workqueue.

UDC should not be pulled up unless gadget driver is bound. The new flag
"allow_connect" is now set by gadget_bind_driver() and cleared by
gadget_unbind_driver(). This prevents work item to pull up the gadget
even if queued when the gadget driver is already unbound.

Cc: stable@vger.kernel.org
Fixes: 1016fc0c096c ("USB: gadget: Fix obscure lockdep violation for udc_mutex")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-1-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.

Build:

- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.

It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.

libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.

Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.

- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.

- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:

$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)

- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.

- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.

- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.

- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:

Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev

- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.

perf BPF filters:

- New feature where BPF can be used to filter samples, for instance:

$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)

- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:

Essentially the BPF filter expression is:

<term> <operator> <value> (("," | "||") <term> <operator> <value>)*

The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops

The <operator> can be one of:
==, !=, >, >=, <, <=, &

The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)

perf lock contention:

- Show lock type with address.

- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:

$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80

- Update default map size to 16384.

- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.

- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).

- Fix problems found with MSAn.

perf report/top:

- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.

- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.

perf sched:

- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d482 ("perf sched: Prefer sched_waking event when it
exists").

perf ftrace:

- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:

# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#

perf top:

- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.

- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.

perf annotate:

- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.

perf kvm:

- Add TUI mode for 'perf kvm stat report'.

Reference counting:

- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.

To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:

https://perf.wiki.kernel.org/index.php/Reference_Count_Checking

- The above caught, for instance, fix, present in this series:

- Fix maps use after put in 'perf test "Share thread maps"':

'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.

Fixed by reversing the order of puts so that the leader is put
last.

- Also several fixes were made to places where reference counts were
not being held.

- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.

ARM64:

- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.

- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".

arm64 vendor events:

- Add N1 metrics.

Intel vendor events:

- Add graniterapids, grandridge and sierraforrest events.

- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp

- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.

perf stat:

- Implement --topdown using JSON metrics.

- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.

- Use metrics for --smi-cost.

- Update topdown documentation.

Vendor events (JSON) infrastructure:

- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:

{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},

- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.

- Support for printing metric thresholds in 'perf list'.

- Add --metric-no-threshold option to 'perf stat'.

- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.

- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.

S/390:

- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).

- Add cache metrics for z13, z14, z15 and z16.

- Add metric for TLB and cache.

ARM:

- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.

Intel PT hardware tracing:

- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.

- Add support for new branch instructions ERETS and ERETU.

- Fix CYC timestamps after standalone CBR

ARM CoreSight hardware tracing:

- Allow user to override timestamp and contextid settings.

- Fix segfault in dso lookup.

- Fix timeless decode mode detection.

- Add separate decode paths for timeless and per-thread modes.

auxtrace:

- Fix address filter entire kernel size.

Miscellaneous:

- Fix use-after-free and unaligned bugs in the PLT handling routines.

- Use zfree() to reduce chances of use after free.

- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.

- Suppress massive unsupported target platform errors in the unwind
code.

- Fix return incorrect build_id size in elf_read_build_id().

- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .

- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.

- Add 'perf bench syscall fork' benchmark.

- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.

- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.

- Fix some spelling mistakes"

* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...

Pull i2c fixes from Wolfram Sang:
"Biggest news is that Andi Shyti steps in for maintaining the
controller drivers. Thank you very much!

Other than that, one new driver maintainer and the rest is usual
driver bugfixes. at24 has a Kconfig dependecy fix"

* tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver
eeprom: at24: also select REGMAP
i2c: sprd: Delete i2c adapter in .remove's error path
i2c: mv64xxx: Fix reading invalid status value in atomic mode
i2c: designware: fix idx_write_cnt in read loop
i2c: mchp-pci1xxxx: Avoid cast to incompatible function type
i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"
MAINTAINERS: Add myself as I2C host drivers maintainer

This patch add the validation for smb request protocol id.
If it is not one of the four ids(SMB1_PROTO_NUMBER, SMB2_PROTO_NUMBER,
SMB2_TRANSFORM_PROTO_NUM, SMB2_COMPRESSION_TRANSFORM_ID), don't allow
processing the request. And this will fix the following KASAN warning
also.

[ 13.905265] BUG: KASAN: slab-out-of-bounds in init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.905900] Read of size 16 at addr ffff888005fd2f34 by task kworker/0:2/44
...
[ 13.908553] Call Trace:
[ 13.908793] <TASK>
[ 13.908995] dump_stack_lvl+0x33/0x50
[ 13.909369] print_report+0xcc/0x620
[ 13.910870] kasan_report+0xae/0xe0
[ 13.911519] kasan_check_range+0x35/0x1b0
[ 13.911796] init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.912492] handle_ksmbd_work+0xe5/0x820

Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.

Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.

smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.

Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.

On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.

Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21

Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:

-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1

This is also expected to make the scheduler do rather wonky things
too.

[ dhansen: remove CPUID detail from changelog, add end user effects ]

CC: stable@kernel.org
Fixes: bbb65d2d365e ("x86: use cpuid vector 0xb when available for detecting cpu topology")
Fixes: 95f3d39ccf7a ("x86/cpu/topology: Provide detect_extended_topology_early()")
Suggested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com

Pull parisc architecture fixes from Helge Deller:

- Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag

- Include reboot.h to avoid gcc-12 compiler warning

* tag 'parisc-for-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
parisc: kexec: include reboot.h

Add a return to the error path when cxl_cdat_read_table() fails. Current
code continues with the table pointer points to freed memory.

Fixes: 7a877c923995 ("cxl/pci: Simplify CDAT retrieval error path")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/168382793506.3510737.4792518576623749076.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The tpg->np_login_sem is a semaphore that is used to serialize the login
process when multiple login threads run concurrently against the same
target portal group.

The iscsi_target_locate_portal() function finds the tpg, calls
iscsit_access_np() against the np_login_sem semaphore and saves the tpg
pointer in conn->tpg;

If iscsi_target_locate_portal() fails, the caller will check for the
conn->tpg pointer and, if it's not NULL, then it will assume that
iscsi_target_locate_portal() called iscsit_access_np() on the semaphore.

Make sure that conn->tpg gets initialized only if iscsit_access_np() was
successful, otherwise iscsit_deaccess_np() may end up being called against
a semaphore we never took, allowing more than one thread to access the same
tpg.

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/20230508162219.1731964-4-mlombard@redhat.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull drm fixes from Dave Airlie:
"A bunch of misc fixes across the board.

amdgpu is the usual bulk with a revert and other fixes, nouveau has a
race fix that was causing a UAF that was hard hanging systems,
otherwise some qaic, bridge and radeon.

amdgpu:
- GFX9 preemption fixes
- Add missing radeon secondary PCI ID
- vblflash fixes
- SMU 13 fix
- VCN 4.0 fix
- Re-enable TOPDOWN flag for large BAR systems to fix regression
- eDP fix
- PSR hang fix
- DPIA fix

radeon:
- fbdev client warning fix

qaic:
- leak fix
- null ptr deref fix

nouveau:
- use-after-free caused by fence race fix
- runtime pm fix
- NULL ptr checks

bridge:
- ti-sn65dsi86: Avoid possible buffer overflow"

* tag 'drm-fixes-2023-06-17' of git://anongit.freedesktop.org/drm/drm: (21 commits)
nouveau: fix client work fence deletion race
drm/amd/display: limit DPIA link rate to HBR3
drm/amd/display: fix the system hang while disable PSR
drm/amd/display: edp do not add non-edid timings
Revert "drm/amdgpu: remove TOPDOWN flags when allocating VRAM in large bar system"
drm/amdgpu: vcn_4_0 set instance 0 init sched score to 1
drm/radeon: Disable outputs when releasing fbdev client
drm/amd/pm: workaround for compute workload type on some skus
drm/amd: Tighten permissions on VBIOS flashing attributes
drm/amd: Make sure image is written to trigger VBIOS image update flow
drm/amdgpu: add missing radeon secondary PCI ID
drm/amdgpu: Implement gfx9 patch functions for resubmission
drm/amdgpu: Modify indirect buffer packages for resubmission
drm/amdgpu: Program gds backup address as zero if no gds allocated
drm/nouveau: add nv_encoder pointer check for NULL
drm/amdgpu: Reset CP_VMID_PREEMPT after trailing fence signaled
drm/nouveau/dp: check for NULL nv_connector->native_mode
drm/bridge: ti-sn65dsi86: Avoid possible buffer overflow
drm/nouveau: don't detect DSM for non-NVIDIA device
accel/qaic: Fix NULL pointer deref in qaic_destroy_drm_device()
...

sparse points out an embarrasing bug in an older patch of mine,
which uses the register offset instead of an __iomem pointer:

drivers/clk/pxa/clk-pxa3xx.c:167:9: sparse: sparse: Using plain integer as NULL pointer

Unlike sparse, gcc and clang ignore this bug and fail to warn
because a literal '0' is considered a valid representation of
a NULL pointer.

Fixes: 3c816d950a49 ("ARM: pxa: move clk register definitions to driver")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305111301.RAHohdob-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230511105845.299859-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Currently, the error interrupt is never acknowledged, so once active it
will stay active indefinitely, causing the handler to be called in an
infinite loop.

Fixes: 2f0fc4159a6a ("SERIAL: Lantiq: Add driver for MIPS Lantiq SOCs.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bernhard Seibold <mail@bernhard-seibold.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Message-ID: <20230602133029.546-1-mail@bernhard-seibold.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current implementation mistakenly performs a & operation on
the output of sysfs_emit. This patch performs the & operation before
calling sysfs_emit.

Fixes: 662a60102c12 ("usb: typec: Separate USB Power Delivery from USB Type-C")
Cc: stable <stable@kernel.org>
Reported-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Pavan Holla <pholla@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Message-ID: <20230607193328.3359487-1-pholla@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull debugobjects fix from Thomas Gleixner:
"A single fix for debugobjects:

The recent fix to ensure atomicity of lookup and allocation
inadvertently broke the pool refill mechanism, so that debugobject
OOMs now in certain situations. The reason is that the functions which
got updated no longer invoke debug_objecs_init(), which is now the
only place to care about refilling the tracking object pool.

Restore the original behaviour by adding explicit refill opportunities
to those places"

* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debugobject: Ensure pool refill (again)

This reverts commit a980755beb5aca9002e1c95ba519b83a44242b5b.

We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull soundwire fixes from Vinod Koul:
"Core fix for missing flag clear, error patch handling in qcom driver
and BIOS quirk for HP Spectre x360:

- HP Spectre x360 soundwire DMI quirk

- Error path handling for qcom driver

- Core fix for missing clear of alloc_slave_rt"

* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: Add missing clear of alloc_slave_rt
soundwire: qcom: add proper error paths in qcom_swrm_startup()
soundwire: dmi-quirks: add new mapping for HP Spectre x360

at24 fixes for v6.4-rc6

- fix a Kconfig issue (we need to select REGMAP, not only REGMAP_I2C)

The length field of netbios header must be greater than the SMB header
sizes(smb1 or smb2 header), otherwise the packet is an invalid SMB packet.

If `pdu_size` is 0, ksmbd allocates a 4 bytes chunk to `conn->request_buf`.
In the function `get_smb2_cmd_val` ksmbd will read cmd from
`rcv_hdr->Command`, which is `conn->request_buf + 12`, causing the KASAN
detector to print the following error message:

[ 7.205018] BUG: KASAN: slab-out-of-bounds in get_smb2_cmd_val+0x45/0x60
[ 7.205423] Read of size 2 at addr ffff8880062d8b50 by task ksmbd:42632/248
...
[ 7.207125] <TASK>
[ 7.209191] get_smb2_cmd_val+0x45/0x60
[ 7.209426] ksmbd_conn_enqueue_request+0x3a/0x100
[ 7.209712] ksmbd_server_process_request+0x72/0x160
[ 7.210295] ksmbd_conn_handler_loop+0x30c/0x550
[ 7.212280] kthread+0x160/0x190
[ 7.212762] ret_from_fork+0x1f/0x30
[ 7.212981] </TASK>

Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)

Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.

As a workaround, never enable PCIDs on affected processors.

I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.

Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.

Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

Pull ARM fixes from Russell King:

- fix unwinder for uleb128 case

- fix kernel-doc warnings for HP Jornada 7xx

- fix unbalanced stack on vfp success path

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9297/1: vfp: avoid unbalanced stack on 'success' return path
ARM: 9296/1: HP Jornada 7XX: fix kernel-doc warnings
ARM: 9295/1: unwind:fix unwind abort for uleb128 case

Fix the __swp_offset() and __swp_entry() macros due to commit 6d239fc78c0b
("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE") which introduced the
SWP_EXCLUSIVE flag by reusing the _PAGE_ACCESSED flag.

Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Tested-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 6d239fc78c0b ("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE")
Cc: <stable@vger.kernel.org> # v6.3+

Starting with commit:

95433f726301 ("srcu: Begin offloading srcu_struct fields to srcu_update")

...it is no longer possible to do:

static DEFINE_SRCU(x)

Switch to DEFINE_STATIC_SRCU(x) to fix:

tools/testing/cxl/test/mock.c:22:1: error: duplicate ‘static’
22 | static DEFINE_SRCU(cxl_mock_srcu);
| ^~~~~~

Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168392709546.1135523.10424917245934547117.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/20230508162219.1731964-3-mlombard@redhat.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In the same spirit as commit ca57f02295f1 ("afs: Fix fileserver probe
RTT handling"), don't rule out using a vlserver just because there
haven't been enough packets yet to calculate a real rtt. Always set the
server's probe rtt from the estimate provided by rxrpc_kernel_get_srtt,
which is capped at 1 second.

This could lead to EDESTADDRREQ errors when accessing a cell for the
first time, even though the vl servers are known and have responded to a
probe.

Fixes: 1d4adfaf6574 ("rxrpc: Make rxrpc_kernel_get_srtt() indicate validity")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2023-June/006746.html
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drm-misc-fixes maybe in time for v6.4-rc7:
- qaic leak and null deref fix.
- Fix runtime pm in nouveau.
- Fix array overflow in ti-sn65dsi86 pwm chip handling.
- Assorted null check fixes in nouveau.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <dev@lankhorst.se>
Link: https://patchwork.freedesktop.org/patch/msgid/641eb8a8-fbd7-90ad-0805-310b7fec9344@lankhorst.se

As clk_core_populate_parent_map() checks clk_init_data.num_parents
first, and checks clk_init_data.parent_names[] before
clk_init_data.parent_data[] and clk_init_data.parent_hws[].

Therefore the clk_init_data structure needs to be explicitly initialised
to prevent an unexpected crash if clk_init_data.parent_names[] is a
random value.

CPU 0 Unable to handle kernel paging request at virtual address 0000000000000dc0, era == 9000000002986290, ra == 900000000298624c
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.4.0-rc2+ #4582
pc 9000000002986290 ra 900000000298624c tp 9000000100094000 sp 9000000100097a60
a0 9000000104541e00 a1 0000000000000000 a2 0000000000000dc0 a3 0000000000000001
a4 90000001000979f0 a5 90000001800977d7 a6 0000000000000000 a7 900000000362a000
t0 90000000034f3548 t1 6f8c2a9cb5ab5f64 t2 0000000000011340 t3 90000000031cf5b0
t4 0000000000000dc0 t5 0000000000000004 t6 0000000000011300 t7 9000000104541e40
t8 000000000005a4f8 u0 9000000104541e00 s9 9000000104541e00 s0 9000000104bc4700
s1 9000000104541da8 s2 0000000000000001 s3 900000000356f9d8 s4 ffffffffffffffff
s5 0000000000000000 s6 0000000000000dc0 s7 90000000030d0a88 s8 0000000000000000
ra: 900000000298624c __clk_register+0x228/0x84c
ERA: 9000000002986290 __clk_register+0x26c/0x84c
CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
PRMD: 00000004 (PPLV0 +PIE -PWE)
EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
BADV: 0000000000000dc0
PRID: 0014a000 (Loongson-64bit, )
Modules linked in:
Process swapper/0 (pid: 1, threadinfo=(____ptrval____), task=(____ptrval____))
Stack : 90000000031c1810 90000000030d0a88 900000000325bac0 90000000034f3548
90000001002ab410 9000000104541e00 0000000000000dc0 9000000003150098
90000000031c1810 90000000031a0460 900000000362a000 90000001002ab410
900000000362a000 9000000104541da8 9000000104541de8 90000001002ab410
900000000362a000 9000000002986a68 90000000034f3ed8 90000000030d0aa8
9000000104541da8 900000000298d3b8 90000000031c1810 0000000000000000
90000000034f3ed8 90000000030d0aa8 0000000000000dc0 90000000030d0a88
90000001002ab410 900000000298d401 0000000000000000 6f8c2a9cb5ab5f64
90000000034f4000 90000000030d0a88 9000000003a48a58 90000001002ab410
9000000104bd81a8 900000000298d484 9000000100020260 0000000000000000
...
Call Trace:
[<9000000002986290>] __clk_register+0x26c/0x84c
[<9000000002986a68>] devm_clk_hw_register+0x5c/0xe0
[<900000000298d3b8>] loongson2_clk_register.constprop.0+0xdc/0x10c
[<900000000298d484>] loongson2_clk_probe+0x9c/0x4ac
[<9000000002a4eba4>] platform_probe+0x68/0xc8
[<9000000002a4bf80>] really_probe+0xbc/0x2f0
[<9000000002a4c23c>] __driver_probe_device+0x88/0x128
[<9000000002a4c318>] driver_probe_device+0x3c/0x11c
[<9000000002a4c5dc>] __driver_attach+0x98/0x18c
[<9000000002a49ca0>] bus_for_each_dev+0x80/0xe0
[<9000000002a4b0dc>] bus_add_driver+0xfc/0x1ec
[<9000000002a4d4a8>] driver_register+0x68/0x134
[<90000000020f0110>] do_one_initcall+0x50/0x188
[<9000000003150f00>] kernel_init_freeable+0x224/0x294
[<90000000030240fc>] kernel_init+0x20/0x110
[<90000000020f1568>] ret_from_kernel_thread+0xc/0xa4

Fixes: acc0ccffec50 ("clk: clk-loongson2: add clock controller driver support")
Cc: stable@vger.kernel.org
Cc: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/20230524014924.2869051-1-zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The Cancel command was passed to the write callback as the
offset instead of as the actual command which caused NULL
pointer dereference.

Reported-by: Stephan Bolten <stephan.bolten@gmx.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217517
Fixes: 094902bc6a3c ("usb: typec: ucsi: Always cancel the command if PPM reports BUSY condition")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Message-ID: <20230606115802.79339-1-heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull crypto fixes from Herbert Xu:

- A long-standing bug in crypto_engine

- A buggy but harmless check in the sun8i-ss driver

- A regression in the CRYPTO_USER interface

* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix CRYPTO_USER checks for report function
crypto: engine - fix crypto_queue backlog handling
crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()

The recent fix to ensure atomicity of lookup and allocation inadvertently
broke the pool refill mechanism.

Prior to that change debug_objects_activate() and debug_objecs_assert_init()
invoked debug_objecs_init() to set up the tracking object for statically
initialized objects. That's not longer the case and debug_objecs_init() is
now the only place which does pool refills.

Depending on the number of statically initialized objects this can be
enough to actually deplete the pool, which was observed by Ido via a
debugobjects OOM warning.

Restore the old behaviour by adding explicit refill opportunities to
debug_objects_activate() and debug_objecs_assert_init().

Fixes: 63a759694eed ("debugobject: Prevent init race with static objects")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/871qk05a9d.ffs@tglx

This reverts commit 51924ae69eea5bc90b5da525fbcf4bbd5f8551b3.

We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>