Pull x86 fix from Borislav Petkov:

- Set up the kernel CS earlier in the boot process in case EFI boots
the kernel after bypassing the decompressor and the CS descriptor
used ends up being the EFI one which is not mapped in the identity
page table, leading to early SEV/SNP guest communication exceptions
resulting in the guest crashing

* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed

Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:

- Fix four slab out of bounds warnings: improve checks for protocol
id, and for small packet length, and for create context parsing,
and for negotiate context parsing

- Fix for incorrect dereferencing POSIX ACLs"

* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: validate smb request protocol id
ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
ksmbd: fix out-of-bound read in parse_lease_state()
ksmbd: fix out-of-bound read in deassemble_neg_contexts()

The call to startup_64_setup_env() will install a new GDT but does not
actually switch to using the KERNEL_CS entry until returning from the
function call.

Commit bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in
boot") moved the call to sme_enable() earlier in the boot process and in
between the call to startup_64_setup_env() and the switch to KERNEL_CS.
An SEV-ES or an SEV-SNP guest will trigger #VC exceptions during the call
to sme_enable() and if the CS pushed on the stack as part of the exception
and used by IRETQ is not mapped by the new GDT, then problems occur.
Today, the current CS when entering startup_64 is the kernel CS value
because it was set up by the decompressor code, so no issue is seen.

However, a recent patchset that looked to avoid using the legacy
decompressor during an EFI boot exposed this bug. At entry to startup_64,
the CS value is that of EFI and is not mapped in the new kernel GDT. So
when a #VC exception occurs, the CS value used by IRETQ is not valid and
the guest boot crashes.

Fix this issue by moving the block that switches to the KERNEL_CS value to
be done immediately after returning from startup_64_setup_env().

Fixes: bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in boot")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/all/6ff1f28af2829cc9aea357ebee285825f90a431f.1684340801.git.thomas.lendacky%40amd.com

Pull i2c fixes from Wolfram Sang:
"Biggest news is that Andi Shyti steps in for maintaining the
controller drivers. Thank you very much!

Other than that, one new driver maintainer and the rest is usual
driver bugfixes. at24 has a Kconfig dependecy fix"

* tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver
eeprom: at24: also select REGMAP
i2c: sprd: Delete i2c adapter in .remove's error path
i2c: mv64xxx: Fix reading invalid status value in atomic mode
i2c: designware: fix idx_write_cnt in read loop
i2c: mchp-pci1xxxx: Avoid cast to incompatible function type
i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"
MAINTAINERS: Add myself as I2C host drivers maintainer

This patch add the validation for smb request protocol id.
If it is not one of the four ids(SMB1_PROTO_NUMBER, SMB2_PROTO_NUMBER,
SMB2_TRANSFORM_PROTO_NUM, SMB2_COMPRESSION_TRANSFORM_ID), don't allow
processing the request. And this will fix the following KASAN warning
also.

[ 13.905265] BUG: KASAN: slab-out-of-bounds in init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.905900] Read of size 16 at addr ffff888005fd2f34 by task kworker/0:2/44
...
[ 13.908553] Call Trace:
[ 13.908793] <TASK>
[ 13.908995] dump_stack_lvl+0x33/0x50
[ 13.909369] print_report+0xcc/0x620
[ 13.910870] kasan_report+0xae/0xe0
[ 13.911519] kasan_check_range+0x35/0x1b0
[ 13.911796] init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.912492] handle_ksmbd_work+0xe5/0x820

Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.

Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.

smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.

Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.

On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.

Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21

Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:

-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1

This is also expected to make the scheduler do rather wonky things
too.

[ dhansen: remove CPUID detail from changelog, add end user effects ]

CC: stable@kernel.org
Fixes: bbb65d2d365e ("x86: use cpuid vector 0xb when available for detecting cpu topology")
Fixes: 95f3d39ccf7a ("x86/cpu/topology: Provide detect_extended_topology_early()")
Suggested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com

Pull soundwire fixes from Vinod Koul:
"Core fix for missing flag clear, error patch handling in qcom driver
and BIOS quirk for HP Spectre x360:

- HP Spectre x360 soundwire DMI quirk

- Error path handling for qcom driver

- Core fix for missing clear of alloc_slave_rt"

* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: Add missing clear of alloc_slave_rt
soundwire: qcom: add proper error paths in qcom_swrm_startup()
soundwire: dmi-quirks: add new mapping for HP Spectre x360

at24 fixes for v6.4-rc6

- fix a Kconfig issue (we need to select REGMAP, not only REGMAP_I2C)

The length field of netbios header must be greater than the SMB header
sizes(smb1 or smb2 header), otherwise the packet is an invalid SMB packet.

If `pdu_size` is 0, ksmbd allocates a 4 bytes chunk to `conn->request_buf`.
In the function `get_smb2_cmd_val` ksmbd will read cmd from
`rcv_hdr->Command`, which is `conn->request_buf + 12`, causing the KASAN
detector to print the following error message:

[ 7.205018] BUG: KASAN: slab-out-of-bounds in get_smb2_cmd_val+0x45/0x60
[ 7.205423] Read of size 2 at addr ffff8880062d8b50 by task ksmbd:42632/248
...
[ 7.207125] <TASK>
[ 7.209191] get_smb2_cmd_val+0x45/0x60
[ 7.209426] ksmbd_conn_enqueue_request+0x3a/0x100
[ 7.209712] ksmbd_server_process_request+0x72/0x160
[ 7.210295] ksmbd_conn_handler_loop+0x30c/0x550
[ 7.212280] kthread+0x160/0x190
[ 7.212762] ret_from_fork+0x1f/0x30
[ 7.212981] </TASK>

Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)

Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.

As a workaround, never enable PCIDs on affected processors.

I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.

Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.

Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for the Qualcomm Snapdragon
platforms.

There are bug fixes for error handling in Qualcomm icc-bwmon,
rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
firmware driver and a missing initialization in the Arm ff-a firmware
driver. The Qualcomm RPMh and EDAC drivers need some rework to work
correctly on all supported chips.

The DT fixes include:

- i.MX8 fixes for gpio, pinmux and clock settings

- ADS touchscreen gpio polarity settings in several machines

- Address dtb warnings for caches, panel and input-enable properties
on Qualcomm platforms

- Incorrect data on qualcomm platforms fir SA8155P power domains,
SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire

- Remoteproc firmware paths are corrected for Sony Xperia 10 IV"

* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
firmware: arm_ffa: Set handle field to zero in memory descriptor
ARM: dts: Fix erroneous ADS touchscreen polarities
arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
EDAC/qcom: Get rid of hardcoded register offsets
EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
dt-bindings: cache: qcom,llcc: Fix SM8550 description
arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
soc: qcom: rpmhpd: Add SA8155P power domains
arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
dt-bindings: power: qcom,rpmpd: Add SA8155P
soc: qcom: Rename ice to qcom_ice to avoid module name conflict
soc: qcom: rmtfs: Fix error code in probe()
soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
ARM: at91: pm: fix imbalanced reference counter for ethernet devices
arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
...

The current path that skips allocating the slave runtime does not clear
the alloc_slave_rt flag, this is clearly incorrect. Add the missing
clear, so the runtime won't be erroneously cleaned up.

Fixes: f3016b891c8c ("soundwire: stream: sdw_stream_add_ functions can be called multiple times")
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230602101140.2040141-1-ckeepax@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add the MAINTAINERS entries for the Renesas RZ/V2M I2C driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.

../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
540 | struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]

Fixes: 5c015258478e ("eeprom: at24: add basic regmap_i2c support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Dan reported the following error message:

fs/smb/server/smbacl.c:1296 smb_check_perm_dacl()
error: 'posix_acls' dereferencing possible ERR_PTR()
fs/smb/server/vfs.c:1323 ksmbd_vfs_make_xattr_posix_acl()
error: 'posix_acls' dereferencing possible ERR_PTR()
fs/smb/server/vfs.c:1830 ksmbd_vfs_inherit_posix_acl()
error: 'acls' dereferencing possible ERR_PTR()

__get_acl() returns a mix of error pointers and NULL. This change it
with IS_ERR_OR_NULL().

Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Enable k10temp on this system.

[ bp: Massage. ]

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230427053338.16653-3-mario.limonciello@amd.com

Pull block fixes from Jens Axboe:

- Fix an issue with the hardware queue nr_active, causing it to become
imbalanced (Tian)

- Fix an issue with null_blk not releasing pages if configured as
memory backed (Nitesh)

- Fix a locking issue in dasd (Jan)

* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
s390/dasd: Use correct lock while counting channel queue length
null_blk: Fix: memory release when memory_backed=1
blk-mq: fix blk_mq_hw_ctx active request accounting

i.MX fixes for 6.4, round 2:

- Fix SPI CS pinmux for the final production version of imx8mn-beacon
board.
- Fix GPIOs for USDHC2 CD and WP signals on imx8qm-mek board.
- Assign default clock rate for i.MX8 LPUARTs to fix UART failure.

* tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals

Link: https://lore.kernel.org/r/20230607141312.GU4199@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Reverse actions in qcom_swrm_startup() error paths to avoid leaking
stream memory and keeping runtime PM unbalanced.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230517163736.997553-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.

So only skip clk disabling if resume failed, but do delete the adapter.

Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This bug is in parse_lease_state, and it is caused by the missing check
of `struct create_context`. When the ksmbd traverses the create_contexts,
it doesn't check if the field of `NameOffset` and `Next` is valid,
The KASAN message is following:

[ 6.664323] BUG: KASAN: slab-out-of-bounds in parse_lease_state+0x7d/0x280
[ 6.664738] Read of size 2 at addr ffff888005c08988 by task kworker/0:3/103
...
[ 6.666644] Call Trace:
[ 6.666796] <TASK>
[ 6.666933] dump_stack_lvl+0x33/0x50
[ 6.667167] print_report+0xcc/0x620
[ 6.667903] kasan_report+0xae/0xe0
[ 6.668374] kasan_check_range+0x35/0x1b0
[ 6.668621] parse_lease_state+0x7d/0x280
[ 6.668868] smb2_open+0xbe8/0x4420
[ 6.675137] handle_ksmbd_work+0x282/0x820

Use smb2_find_context_vals() to find smb2 create request lease context.
smb2_find_context_vals validate create context fields.

Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Tested-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Commit

310e782a99c7 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")

switched to using amd_smn_read() which relies upon the misc PCI ID used
by DF function 3 being included in a table. The ID for model 78h is
missing in that table, so amd_smn_read() doesn't work.

Add the missing ID into amd_nb, restoring s2idle on this system.

[ bp: Simplify commit message. ]

Fixes: 310e782a99c7 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230427053338.16653-2-mario.limonciello@amd.com

Pull virtio bug fixes from Michael Tsirkin:
"A bunch of fixes all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: use canonical ftrace path
vhost_vdpa: support PACKED when setting-getting vring_base
vhost: support PACKED when setting-getting vring_base
vhost: Fix worker hangs due to missed wake up calls
vhost: Fix crash during early vhost_transport_send_pkt calls
vhost_net: revert upend_idx only on retriable error
vhost_vdpa: tell vqs about the negotiated
vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
tools/virtio: Add .gitignore for ringtest
tools/virtio: Fix arm64 ringtest compilation error
vduse: avoid empty string for dev name
vhost: use kzalloc() instead of kmalloc() followed by memset()

The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit
583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.

The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.

Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.

Fixes: 583d6535cb9d ("dasd: remove dead code")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

AMDTEE add return origin to load TA command

* tag 'amdtee-fix-for-v6.5' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'

Link: https://lore.kernel.org/r/20230606075843.GA2792442@rayden
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The final production baseboard had a different chip select than
earlier prototype boards. When the newer board was released,
the SPI stopped working because the wrong pin was used in the device
tree and conflicted with the UART RTS. Fix the pinmux for
production boards.

Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

A BIOS/DMI update seems to have broken some devices, let's add a new
mapping.

Link: https://github.com/thesofproject/linux/issues/4323
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230515074859.3097-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.

My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt

This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.

I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.

Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.

[1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78

Fixes: 544a8d75f3d6 ("i2c: mv64xxx: Add atomic_xfer method to driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.

Build:

- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.

It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.

libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.

Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.

- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.

- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:

$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)

- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.

- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.

- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.

- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:

Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev

- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.

perf BPF filters:

- New feature where BPF can be used to filter samples, for instance:

$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)

- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:

Essentially the BPF filter expression is:

<term> <operator> <value> (("," | "||") <term> <operator> <value>)*

The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops

The <operator> can be one of:
==, !=, >, >=, <, <=, &

The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)

perf lock contention:

- Show lock type with address.

- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:

$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80

- Update default map size to 16384.

- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.

- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).

- Fix problems found with MSAn.

perf report/top:

- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.

- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.

perf sched:

- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d482 ("perf sched: Prefer sched_waking event when it
exists").

perf ftrace:

- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:

# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#

perf top:

- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.

- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.

perf annotate:

- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.

perf kvm:

- Add TUI mode for 'perf kvm stat report'.

Reference counting:

- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.

To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:

https://perf.wiki.kernel.org/index.php/Reference_Count_Checking

- The above caught, for instance, fix, present in this series:

- Fix maps use after put in 'perf test "Share thread maps"':

'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.

Fixed by reversing the order of puts so that the leader is put
last.

- Also several fixes were made to places where reference counts were
not being held.

- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.

ARM64:

- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.

- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".

arm64 vendor events:

- Add N1 metrics.

Intel vendor events:

- Add graniterapids, grandridge and sierraforrest events.

- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp

- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.

perf stat:

- Implement --topdown using JSON metrics.

- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.

- Use metrics for --smi-cost.

- Update topdown documentation.

Vendor events (JSON) infrastructure:

- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:

{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},

- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.

- Support for printing metric thresholds in 'perf list'.

- Add --metric-no-threshold option to 'perf stat'.

- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.

- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.

S/390:

- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).

- Add cache metrics for z13, z14, z15 and z16.

- Add metric for TLB and cache.

ARM:

- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.

Intel PT hardware tracing:

- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.

- Add support for new branch instructions ERETS and ERETU.

- Fix CYC timestamps after standalone CBR

ARM CoreSight hardware tracing:

- Allow user to override timestamp and contextid settings.

- Fix segfault in dso lookup.

- Fix timeless decode mode detection.

- Add separate decode paths for timeless and per-thread modes.

auxtrace:

- Fix address filter entire kernel size.

Miscellaneous:

- Fix use-after-free and unaligned bugs in the PLT handling routines.

- Use zfree() to reduce chances of use after free.

- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.

- Suppress massive unsupported target platform errors in the unwind
code.

- Fix return incorrect build_id size in elf_read_build_id().

- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .

- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.

- Add 'perf bench syscall fork' benchmark.

- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.

- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.

- Fix some spelling mistakes"

* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...

The check in the beginning is
`clen + sizeof(struct smb2_neg_context) <= len_of_ctxts`,
but in the end of loop, `len_of_ctxts` will subtract
`((clen + 7) & ~0x7) + sizeof(struct smb2_neg_context)`, which causes
integer underflow when clen does the 8 alignment. We should use
`(clen + 7) & ~0x7` in the check to avoid underflow from happening.

Then there are some variables that need to be declared unsigned
instead of signed.

[ 11.671070] BUG: KASAN: slab-out-of-bounds in smb2_handle_negotiate+0x799/0x1610
[ 11.671533] Read of size 2 at addr ffff888005e86cf2 by task kworker/0:0/7
...
[ 11.673383] Call Trace:
[ 11.673541] <TASK>
[ 11.673679] dump_stack_lvl+0x33/0x50
[ 11.673913] print_report+0xcc/0x620
[ 11.674671] kasan_report+0xae/0xe0
[ 11.675171] kasan_check_range+0x35/0x1b0
[ 11.675412] smb2_handle_negotiate+0x799/0x1610
[ 11.676217] ksmbd_smb_negotiate_common+0x526/0x770
[ 11.676795] handle_ksmbd_work+0x274/0x810
...

Cc: stable@vger.kernel.org
Signed-off-by: Chih-Yen Chang <cc85nod@gmail.com>
Tested-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Pull ceph fixes from Ilya Dryomov:
"A fix for a potential data corruption in differential backup and
snapshot-based mirroring scenarios in RBD and a reference counting
fixup to avoid use-after-free in CephFS, all marked for stable"

* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
ceph: fix use-after-free bug for inodes when flushing capsnaps
rbd: get snapshot context after exclusive lock is ensured to be held
rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting

The canonical location for the tracefs filesystem is at /sys/kernel/tracing.

But, from Documentation/trace/ftrace.rst:

Before 4.1, all ftrace tracing control files were within the debugfs
file system, which is typically located at /sys/kernel/debug/tracing.
For backward compatibility, when mounting the debugfs file system,
the tracefs file system will be automatically mounted at:

/sys/kernel/debug/tracing

A few spots in tools/virtio still refer to this older debugfs
path, so let's update them to avoid confusion.

Signed-off-by: Ross Zwisler <zwisler@google.com>
Message-Id: <20230215223350.2658616-6-zwisler@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>

Memory/pages are not freed, when unloading nullblk driver.

Steps to reproduce issue
1.free -h
total used free shared buff/cache available
Mem: 7.8Gi 260Mi 7.1Gi 3.0Mi 395Mi 7.3Gi
Swap: 0B 0B 0B
2.modprobe null_blk memory_backed=1
3.dd if=/dev/urandom of=/dev/nullb0 oflag=direct bs=1M count=1000
4.modprobe -r null_blk
5.free -h
total used free shared buff/cache available
Mem: 7.8Gi 1.2Gi 6.1Gi 3.0Mi 398Mi 6.3Gi
Swap: 0B 0B 0B

Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Nitesh Shetty <nj.shetty@samsung.com>
Link: https://lore.kernel.org/r/20230605062354.24785-1-nj.shetty@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Arm FF-A fix for v6.4

A single fix addressing another MBZ field being non-zero and non-compliant
resulting in the rejection of certain memory interface transmissions by
the receivers(secure partitions). The issue was addressed before but missed
to address this one field which is part of this change.

* tag 'ffa-fix-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Set handle field to zero in memory descriptor

Link: https://lore.kernel.org/r/20230606125720.2816923-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

After TEE has completed processing of TEE_CMD_ID_LOAD_TA, set proper
value in 'return_origin' argument passed by open_session() call. To do
so, add 'return_origin' field to the structure tee_cmd_load_ta. The
Trusted OS shall update return_origin as part of TEE processing.

This change to 'struct tee_cmd_load_ta' interface requires a similar update
in AMD-TEE Trusted OS's TEE_CMD_ID_LOAD_TA interface.

This patch has been verified on Phoenix Birman setup. On older APUs,
return_origin value will be 0.

Cc: stable@vger.kernel.org
Fixes: 757cc3e9ff1d ("tee: add AMD-TEE driver")
Tested-by: Sourabh Das <sourabh.das@amd.com>
Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>

Add the assigned-clocks and assigned-clock-rates properties for the
LPUARTx nodes. Without these properties, the default clock rate
used would be 0, which can cause the UART ports to fail when open.

Fixes: 35f4e9d7530f ("arm64: dts: imx8: split adma ss into dma and audio ss")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until
RX FIFO is empty. When testing with the slave-eeprom, each transaction
has 2 bytes for address/index and 1 byte for value, the address byte
can be written as data byte due to dropping STOP condition.

In the test below, the master continuously writes to the slave, first 2
bytes are index, 3rd byte is value and follow by a STOP condition.

i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3]

Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so
next 2 bytes can be treated as buffer index for upcoming transaction.
Supposedly the slave eeprom buffer would be written as

EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0xD2
EEPROM[0x00D3] = 0xD3

When CPU load is high the slave irq handler may not read fast enough,
the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET
(0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see
the transactions below.

0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4

After `D1` is received, read loop continues to read `00` which is the
first bype of next index. Since STOP condition is ignored by the loop,
eeprom buffer index increased to `D2` and `00` is written as value.

So the slave eeprom buffer becomes

EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0x00
EEPROM[0x00D3] = 0xD3

The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split
the transactions. The first index byte in this case would have bit 11
set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event
which will reset `idx_write_cnt` in slave eeprom.

Signed-off-by: David Zheng <david.zheng@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull debugobjects fix from Thomas Gleixner:
"A single fix for debugobjects:

The recent fix to ensure atomicity of lookup and allocation
inadvertently broke the pool refill mechanism, so that debugobject
OOMs now in certain situations. The reason is that the functions which
got updated no longer invoke debug_objecs_init(), which is now the
only place to care about refilling the tracking object pool.

Restore the original behaviour by adding explicit refill opportunities
to those places"

* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debugobject: Ensure pool refill (again)

This reverts commit a980755beb5aca9002e1c95ba519b83a44242b5b.

We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull smb server fixes from Steve French:
"Eight server fixes (most also for stable):

- Two fixes for uninitialized pointer reads (rename and link)

- Fix potential UAF in oplock break

- Two fixes for potential out of bound reads in negotiate

- Fix crediting bug

- Two fixes for xfstests (allocation size fix for test 694 and lookup
issue shown by test 464)"

* tag '6.4-rc4-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: call putname after using the last component
ksmbd: fix incorrect AllocationSize set in smb2_get_info
ksmbd: fix UAF issue from opinfo->conn
ksmbd: fix multiple out-of-bounds read during context decoding
ksmbd: fix slab-out-of-bounds read in smb2_handle_negotiate
ksmbd: fix credit count leakage
ksmbd: fix uninitialized pointer read in smb2_create_link()
ksmbd: fix uninitialized pointer read in ksmbd_vfs_rename()

Pull RISC-V fixes from Palmer Dabbelt:

- A fix to avoid ISA-disallowed privilege mappings that can result from
WRITE+EXEC mmap requests from userspace.

- A fix for kfence to handle the huge pages.

- A fix to avoid converting misaligned VAs to huge pages.

- ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE has been selected so kprobe
can understand user pointers.

* tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix kprobe __user string arg print fault issue
riscv: Check the virtual alignment before choosing a map size
riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD
riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable

There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:

== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING

To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.

[ idryomov: need_put int -> bool ]

Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

The nr_active counter continues to increase over time which causes the
blk_mq_get_tag to hang until the thread is rescheduled to a different
core despite there are still tags available.

kernel-stack

INFO: task inboundIOReacto:3014879 blocked for more than 2 seconds
Not tainted 6.1.15-amd64 #1 Debian 6.1.15~debian11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:inboundIOReacto state:D stack:0 pid:3014879 ppid:4557 flags:0x00000000
Call Trace:
<TASK>
__schedule+0x351/0xa20
scheduler+0x5d/0xe0
io_schedule+0x42/0x70
blk_mq_get_tag+0x11a/0x2a0
? dequeue_task_stop+0x70/0x70
__blk_mq_alloc_requests+0x191/0x2e0

kprobe output showing RQF_MQ_INFLIGHT bit is not cleared before
__blk_mq_free_request being called.

320 320 kworker/29:1H __blk_mq_free_request rq_flags 0x220c0 in-flight 1
b'__blk_mq_free_request+0x1 [kernel]'
b'bt_iter+0x50 [kernel]'
b'blk_mq_queue_tag_busy_iter+0x318 [kernel]'
b'blk_mq_timeout_work+0x7c [kernel]'
b'process_one_work+0x1c4 [kernel]'
b'worker_thread+0x4d [kernel]'
b'kthread+0xe6 [kernel]'
b'ret_from_fork+0x1f [kernel]'

Signed-off-by: Tian Lan <tian.lan@twosigma.com>
Fixes: 2e315dc07df0 ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230513221227.497327-1-tilan7663@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Several device tree files get the polarity of the pendown-gpios
wrong: this signal is active low. Fix up all incorrect flags, so
that operating systems can rely on the flag being correctly set.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

As described in the commit 111a833dc5cb ("firmware: arm_ffa: Set
reserved/MBZ fields to zero in the memory descriptors") some fields in
the memory descriptor have to be zeroed explicitly. The handle field is
one of these, but it was left out from that change, fix this now.

Fixes: 111a833dc5cb ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors")
Reported-by: Imre Kis <imre.kis@arm.com>
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Link: https://lore.kernel.org/r/20230601140749.93812-1-balint.dobszay@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

The USDHC2 CD and WP sginal should be on LSIO_GPIO5.

Fixes: 307fd14d4b14 ("arm64: dts: imx: add imx8qm mek support")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type,
update the type to match that expected by __devm_add_action.

Reported by clang-16 with W-1:

.../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action'
__devm_add_action(release, action, data, #action)
^~~~~~

No functional change intended.
Compile tested only.

Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Tharun Kumar P<tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull crypto fixes from Herbert Xu:

- A long-standing bug in crypto_engine

- A buggy but harmless check in the sun8i-ss driver

- A regression in the CRYPTO_USER interface

* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix CRYPTO_USER checks for report function
crypto: engine - fix crypto_queue backlog handling
crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()

The recent fix to ensure atomicity of lookup and allocation inadvertently
broke the pool refill mechanism.

Prior to that change debug_objects_activate() and debug_objecs_assert_init()
invoked debug_objecs_init() to set up the tracking object for statically
initialized objects. That's not longer the case and debug_objecs_init() is
now the only place which does pool refills.

Depending on the number of statically initialized objects this can be
enough to actually deplete the pool, which was observed by Ido via a
debugobjects OOM warning.

Restore the old behaviour by adding explicit refill opportunities to
debug_objects_activate() and debug_objecs_assert_init().

Fixes: 63a759694eed ("debugobject: Prevent init race with static objects")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/871qk05a9d.ffs@tglx

This reverts commit 51924ae69eea5bc90b5da525fbcf4bbd5f8551b3.

We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull smb client fixes from Steve French:
"Four small smb3 client fixes:

- two small fixes suggested by kernel test robot

- small cleanup fix

- update Paulo's email address in the maintainer file"

* tag '6.4-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: address unused variable warning
smb: delete an unnecessary statement
smb3: missing null check in SMB2_change_notify
smb3: update a reviewer email in MAINTAINERS file

last component point filename struct. Currently putname is called after
vfs_path_parent_lookup(). And then last component is used for
lookup_one_qstr_excl(). name in last component is freed by previous
calling putname(). And It cause file lookup failure when testing
generic/464 test of xfstest.

Fixes: 74d7970febf7 ("ksmbd: fix racy issue from using ->d_parent and ->d_name")
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

Pull s390 fixes from Alexander Gordeev:

- Avoid linker error for randomly generated config file that has
CONFIG_BRANCH_PROFILE_NONE enabled and make it similar to riscv, x86
and also to commit 4bf3ec384edf ("s390: disable branch profiling for
vdso").

- Currently, if the device is offline and all the channel paths are
either configured or varied offline, the associated subchannel gets
unregistered. Don't unregister the subchannel, instead unregister
offline device.

* tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/purgatory: disable branch profiling
s390/cio: unregister device when the only path is gone

On riscv qemu platform, when add kprobe event on do_sys_open() to show
filename string arg, it just print fault as follow:

echo 'p:myprobe do_sys_open dfd=$arg1 filename=+0($arg2):string flags=$arg3
mode=$arg4' > kprobe_events

bash-166 [000] ...1. 360.195367: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-166 [000] ...1. 360.219369: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-191 [000] ...1. 360.378827: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x98800 mode=0x0

As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:

bash-166 [000] ...1. 96.767641: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-166 [000] ...1. 96.793751: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-177 [000] ...1. 96.962354: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/sys/kernel/debug/tracing/events/kprobes/"
flags=0x98800 mode=0x0

Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Fixes: 0ebeea8ca8a4 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Link: https://lore.kernel.org/r/20230504072910.3742842-1-ruanjinjie@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Move capturing the snapshot context into the image request state
machine, after exclusive lock is ensured to be held for the duration of
dealing with the image request. This is needed to ensure correctness
of fast-diff states (OBJECT_EXISTS vs OBJECT_EXISTS_CLEAN) and object
deltas computed based off of them. Otherwise the object map that is
forked for the snapshot isn't guaranteed to accurately reflect the
contents of the snapshot when the snapshot is taken under I/O. This
breaks differential backup and snapshot-based mirroring use cases with
fast-diff enabled: since some object deltas may be incomplete, the
destination image may get corrupted.

Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/61472
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>