tjh.dev
commits
Pull i2c fixes from Wolfram Sang:
- hisi: update maintainership
- fix several issues in rtl9300 xfer:
- check message length boundaries
- correct multi-byte value composition on write
- increase polling timeout
- fix block transfer protocol
* tag 'i2c-for-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rtl9300: Add missing count byte for SMBus Block Ops
i2c: rtl9300: Increase timeout for transfer polling
i2c: rtl9300: Fix multi-byte I2C write
i2c: rtl9300: Fix out-of-bounds bug in rtl9300_i2c_smbus_xfer
MAINTAINERS: i2c: Update i2c_hisi entry
Pull perf fix from Borislav Petkov:
- Fix a case where the events throttling logic operates on inactive
events
* tag 'perf_urgent_for_v6.17_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Avoid undefined behavior from stopping/starting inactive events
i2c-host-fixes for v6.17-rc3
- hisi: update maintainership
- rtl9300: fix several issues in xfer
- check message length boundaries
- correct multi-byte value composition on write
- increase polling timeout
- fix block transfer protocol
Pull x86 fixes from Borislav Petkov:
- Fix the GDS mitigation detection on some machines after the recent
attack vectors conversion
- Filter out the invalid machine reset reason value -1 when running as
a guest as in such cases the reason why the machine was rebooted does
not make a whole lot of sense
- Init the resource control machinery on Hygon hw in order to avoid a
division by zero and to actually enable the feature on hw which
supports it
* tag 'x86_urgent_for_v6.17_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Fix GDS mitigation selecting when mitigation is off
x86/CPU/AMD: Ignore invalid reset reason value
x86/cpu/hygon: Add missing resctrl_cpu_detect() in bsp_init helper
Calling pmu->start()/stop() on perf events in PERF_EVENT_STATE_OFF can
leave event->hw.idx at -1. When PMU drivers later attempt to use this
negative index as a shift exponent in bitwise operations, it leads to UBSAN
shift-out-of-bounds reports.
The issue is a logical flaw in how event groups handle throttling when some
members are intentionally disabled. Based on the analysis and the
reproducer provided by Mark Rutland (this issue on both arm64 and x86-64).
The scenario unfolds as follows:
1. A group leader event is configured with a very aggressive sampling
period (e.g., sample_period = 1). This causes frequent interrupts and
triggers the throttling mechanism.
2. A child event in the same group is created in a disabled state
(.disabled = 1). This event remains in PERF_EVENT_STATE_OFF.
Since it hasn't been scheduled onto the PMU, its event->hw.idx remains
initialized at -1.
3. When throttling occurs, perf_event_throttle_group() and later
perf_event_unthrottle_group() iterate through all siblings, including
the disabled child event.
4. perf_event_throttle()/unthrottle() are called on this inactive child
event, which then call event->pmu->start()/stop().
5. The PMU driver receives the event with hw.idx == -1 and attempts to
use it as a shift exponent. e.g., in macros like PMCNTENSET(idx),
leading to the UBSAN report.
The throttling mechanism attempts to start/stop events that are not
actively scheduled on the hardware.
Move the state check into perf_event_throttle()/perf_event_unthrottle() so
that inactive events are skipped entirely. This ensures only active events
with a valid hw.idx are processed, preventing undefined behavior and
silencing UBSAN warnings. The corrected check ensures true before
proceeding with PMU operations.
The problem can be reproduced with the syzkaller reproducer:
Fixes: 9734e25fbf5a ("perf: Fix the throttle logic for a group")
Signed-off-by: Yunseong Kim <ysk@kzalloc.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20250812181046.292382-2-ysk@kzalloc.com
The expected on-wire format of an SMBus Block Write is
S Addr Wr [A] Comm [A] Count [A] Data [A] Data [A] ... [A] Data [A] P
Everything starting from the Count byte is provided by the I2C subsystem in
the array data->block. But the driver was skipping the Count byte
(data->block[0]) when sending it to the RTL93xx I2C controller.
Only the actual data could be seen on the wire:
S Addr Wr [A] Comm [A] Data [A] Data [A] ... [A] Data [A] P
This wire format is not SMBus Block Write compatible but matches the format
of an I2C Block Write. Simply adding the count byte to the buffer for the
I2C controller is enough to fix the transmission.
This also affects read because the I2C controller must receive the count
byte + $count * data bytes.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-4-cd9dca0db722@narfation.org
Pull MIPS fixes from Thomas Bogendoerfer:
"Fix ethernet on Lantiq boards"
* tag 'mips-fixes_6.17_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: lantiq: xway: sysctrl: rename the etop node
mips: dts: lantiq: danube: add missing burst length property
The current GDS mitigation logic incorrectly returns early when the
attack vector mitigation is turned off, which leads to two problems:
1. CPUs without ARCH_CAP_GDS_CTRL support are incorrectly marked with
GDS_MITIGATION_OFF when they should be marked as
GDS_MITIGATION_UCODE_NEEDED.
2. The mitigation state checks and locking verification that follow are
skipped, which means:
- fail to detect if the mitigation was locked
- miss the warning when trying to disable a locked mitigation
Remove the early return to ensure proper mitigation state handling. This
allows:
- Proper mitigation classification for non-ARCH_CAP_GDS_CTRL CPUs
- Complete mitigation state verification
This also addresses the failed MSR 0x123 write attempt at boot on
non-ARCH_CAP_GDS_CTRL CPUs:
unchecked MSR access error: WRMSR to 0x123 (tried to write 0x0000000000000010) at rIP: ... (update_gds_msr)
Call Trace:
identify_secondary_cpu
start_secondary
common_startup_64
WARNING: CPU: 1 PID: 0 at arch/x86/kernel/cpu/bugs.c:1053 update_gds_msr
[ bp: Massage, zap superfluous braces. ]
Fixes: 8c7261abcb7ad ("x86/bugs: Add attack vector controls for GDS")
Suggested-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Link: https://lore.kernel.org/20250819023356.2012-1-lirongqing@baidu.com
Pull x86 fixes from Borislav Petkov:
- Remove a transitional asm/cpuid.h header which was added only as a
fallback during cpuid helpers reorg
- Initialize reserved fields in the SVSM page validation calls
structure to zero in order to allow for future structure extensions
- Have the sev-guest driver's buffers used in encryption operations be
in linear mapping space as the encryption operation can be offloaded
to an accelerator
- Have a read-only MSR write when in an AMD SNP guest trap to the
hypervisor as it is usually done. This makes the guest user
experience better by simply raising a #GP instead of terminating said
guest
- Do not output AVX512 elapsed time for kernel threads because the data
is wrong and fix a NULL pointer dereferencing in the process
- Adjust the SRSO mitigation selection to the new attack vectors
* tag 'x86_urgent_for_v6.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpuid: Remove transitional <asm/cpuid.h> header
x86/sev: Ensure SVSM reserved fields in a page validation entry are initialized to zero
virt: sev-guest: Satisfy linear mapping requirement in get_derived_key()
x86/sev: Improve handling of writes to intercepted TSC MSRs
x86/fpu: Fix NULL dereference in avx512_status()
x86/bugs: Select best SRSO mitigation
The timeout for transfers was only set to 2ms. Because of this relatively
low limit, 12-byte read operations to the frontend MCU of a RTL8239 POE PSE
chip cluster was consistently resulting in a timeout.
The original OpenWrt downstream driver [1] was not using any timeout limit
at all. This is also possible by setting the timeout_us parameter of
regmap_read_poll_timeout() to 0. But since the driver currently implements
the ETIMEDOUT error, it is more sensible to increase the timeout in such a
way that communication with the (quite common) Realtek I2C-connected POE
management solution is possible.
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-6.12/drivers/i2c/busses/i2c-rtl9300.c;h=c4d973195ef39dc56d6207e665d279745525fcac#l202
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-3-cd9dca0db722@narfation.org
Pull modules fix from Daniel Gomez:
"This includes a fix part of the KSPP (Kernel Self Protection Project)
to replace the deprecated and unsafe strcpy() calls in the kernel
parameter string handler and sysfs parameters for built-in modules.
Single commit, no functional changes"
* tag 'modules-6.17-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux:
params: Replace deprecated strcpy() with strscpy() and memcpy()
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad93741 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
The reset reason value may be "all bits set", e.g. 0xFFFFFFFF. This is a
commonly used error response from hardware. This may occur due to a real
hardware issue or when running in a VM.
The user will see all reset reasons reported in this case.
Check for an error response value and return early to avoid decoding
invalid data.
Also, adjust the data variable type to match the hardware register size.
Fixes: ab8131028710 ("x86/CPU/AMD: Print the reason for the last reset")
Reported-by: Libing He <libhe@redhat.com>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250721181155.3536023-1-yazen.ghannam@amd.com
Pull turbostat updates from Len Brown:
"tools/power turbostat: version 2025.09.09
- Probe and display L3 Cache topology
- Add ability to average an added counter (useful for pre-integrated
"counters", such as Watts)
- Break the limit of 64 built-in counters
- Assorted bug fixes and minor feature tweaks"
* tag 'turbostat-2025.09.09' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2025.09.09
tools/power turbostat: Handle non-root legacy-uncore sysfs permissions
tools/power turbostat: standardize PER_THREAD_PARAMS
tools/power turbostat: Fix DMR support
tools/power turbostat: add format "average" for external attributes
tools/power turbostat: delete GET_PKG()
tools/power turbostat: probe and display L3 cache topology
tools/power turbostat: Support more than 64 built-in-counters
tools/power turbostat.8: Document Totl%C0, Any%C0, GFX%C0, CPUGFX% columns
tools/power turbostat: Fix bogus SysWatt for forked program
tools/power turbostat: Handle cap_get_proc() ENOSYS
tools/power turbostat: Fix build with musl
tools/power turbostat: verify arguments to params --show and --hide
tools/power turbostat: regression fix: --show C1E%
Pull locking fixes from Borislav Petkov:
- Make sure sanity checks down in the mutex lock path happen on the
correct type of task so that they don't trigger falsely
- Use the write unsafe user access pairs when writing a futex value to
prevent an error on PowerPC which does user read and write accesses
differently
* tag 'locking_urgent_for_v6.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking: Fix __clear_task_blocked_on() warning from __ww_mutex_wound() path
futex: Use user_write_access_begin/_end() in futex_put_value()
All CPUID call sites were updated at commit:
968e30006807 ("x86/cpuid: Set <asm/cpuid/api.h> as the main CPUID header")
to include <asm/cpuid/api.h> instead of <asm/cpuid.h>.
The <asm/cpuid.h> header was still retained as a wrapper, just in case
some new code in -next started using it. Now that everything is merged
to Linus' tree, remove the header.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250815070227.19981-2-darwi@linutronix.de
The RTL93xx I2C controller has 4 32 bit registers to store the bytes for
the upcoming I2C transmission. The first byte is stored in the
least-significant byte of the first register. And the last byte in the most
significant byte of the last register. A map of the transferred bytes to
their order in the registers is:
reg 0: 0x04_03_02_01
reg 1: 0x08_07_06_05
reg 2: 0x0c_0b_0a_09
reg 3: 0x10_0f_0e_0d
The i2c_read() function basically demonstrates how the hardware would pick
up bytes from this register set. But the i2c_write() function was just
pushing bytes one after another to the least significant byte of a register
AFTER shifting the last one to the next more significant byte position.
If you would then have tried to send a buffer with numbers 1-11 using
i2c_write(), you would have ended up with following register content:
reg 0: 0x01_02_03_04
reg 1: 0x05_06_07_08
reg 2: 0x00_09_0a_0b
reg 3: 0x00_00_00_00
On the wire, you would then have seen:
Sr Addr Wr [A] 04 A 03 A 02 A 01 A 08 A 07 A 06 A 05 A 0b A 0a A 09 A P
But the correct data transmission was expected to be
Sr Addr Wr [A] 01 A 02 A 03 A 04 A 05 A 06 A 07 A 08 A 09 A 0a A 0b A P
Because of this multi-byte ordering problem, only single byte i2c_write()
operations were executed correctly (on the wire).
By shifting the byte directly to the correct end position in the register,
it is possible to avoid this incorrect byte ordering and fix multi-byte
transmissions.
The second initialization (to 0) of vals was also be dropped because this
array is initialized to 0 on the stack by using `= {};`. This makes the
fix a lot more readable.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Cc: <stable@vger.kernel.org> # v6.13+
Co-developed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-2-cd9dca0db722@narfation.org
Pull char/misc/iio fixes from Greg KH:
"Here are a small number of char/misc/iio and other driver fixes for
6.17-rc3. Included in here are:
- IIO driver bugfixes for reported issues
- bunch of comedi driver fixes
- most core bugfix
- fpga driver bugfix
- cdx driver bugfix
All of these have been in linux-next this week with no reported
issues"
* tag 'char-misc-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
most: core: Drop device reference after usage in get_channel()
comedi: Make insn_rw_emulate_bits() do insn->n samples
comedi: Fix use of uninitialized memory in do_insn_ioctl() and do_insnlist_ioctl()
comedi: pcl726: Prevent invalid irq number
cdx: Fix off-by-one error in cdx_rpmsg_probe()
fpga: zynq_fpga: Fix the wrong usage of dma_map_sgtable()
iio: pressure: bmp280: Use IS_ERR() in bmp280_common_probe()
iio: light: as73211: Ensure buffer holes are zeroed
iio: adc: rzg2l_adc: Set driver data before enabling runtime PM
iio: adc: rzg2l: Cleanup suspend/resume path
iio: adc: ad7380: fix missing max_conversion_rate_hz on adaq4381-4
iio: adc: bd79124: Add GPIOLIB dependency
iio: imu: inv_icm42600: change invalid data error to -EBUSY
iio: adc: ad7124: fix channel lookup in syscalib functions
iio: temperature: maxim_thermocouple: use DMA-safe buffer for spi_read()
iio: adc: ad7173: prevent scan if too many setups requested
iio: proximity: isl29501: fix buffered read on big-endian systems
iio: accel: sca3300: fix uninitialized iio scan data
strcpy() is deprecated; use strscpy() and memcpy() instead.
In param_set_copystring(), we can safely use memcpy() because we already
know the length of the source string 'val' and that it is guaranteed to
be NUL-terminated within the first 'kps->maxlen' bytes.
Link: https://github.com/KSPP/linux/issues/88
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Link: https://lore.kernel.org/r/20250813132200.184064-2-thorsten.blum@linux.dev
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0aa ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Since
923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot")
resctrl_cpu_detect() has been moved from common CPU initialization code to
the vendor-specific BSP init helper, while Hygon didn't put that call in their
code.
This triggers a division by zero fault during early booting stage on our
machines with X86_FEATURE_CQM* supported, where get_rdt_mon_resources() tries
to calculate mon_l3_config with uninitialized boot_cpu_data.x86_cache_occ_scale.
Add the missing resctrl_cpu_detect() in the Hygon BSP init helper.
[ bp: Massage commit message. ]
Fixes: 923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot")
Signed-off-by: Tianxiang Peng <txpeng@tencent.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Hui Li <caelli@tencent.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/20250623093153.3016937-1-txpeng@tencent.com
Pull smp fixes from Borislav Petkov:
- Remove an obsolete comment and fix spelling
* tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Remove obsolete comment from takedown_cpu()
smp: Fix spelling in on_each_cpu_cond_mask()'s doc-comment
Probe and display L3 Cache topology
Add ability to average an added counter
(useful for pre-integrated "counters", such as Watts)
Break the limit of 64 built-in counters.
Assorted bug fixes and minor feature tweaks
Signed-off-by: Len Brown <len.brown@intel.com>
Pull rust fixes from Miguel Ojeda:
- Workaround 'rustdoc' target modifiers bug in Rust >= 1.88.0. It will
be fixed in Rust 1.90.0 (expected 2025-09-18).
- Clean 'rustdoc' output before running it to avoid confusing the tool
when files from previous versions remain.
* tag 'rust-fixes-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: kbuild: clean output before running `rustdoc`
rust: workaround `rustdoc` target modifiers bug
The __clear_task_blocked_on() helper added a number of sanity
checks ensuring we hold the mutex wait lock and that the task
we are clearing blocked_on pointer (if set) matches the mutex.
However, there is an edge case in the _ww_mutex_wound() logic
where we need to clear the blocked_on pointer for the task that
owns the mutex, not the task that is waiting on the mutex.
For this case the sanity checks aren't valid, so handle this
by allowing a NULL lock to skip the additional checks.
K Prateek Nayak and Maarten Lankhorst also pointed out that in
this case where we don't hold the owner's mutex wait_lock, we
need to be a bit more careful using READ_ONCE/WRITE_ONCE in both
the __clear_task_blocked_on() and __set_task_blocked_on()
implementations to avoid accidentally tripping WARN_ONs if two
instances race. So do that here as well.
This issue was easier to miss, I realized, as the test-ww_mutex
driver only exercises the wait-die class of ww_mutexes. I've
sent a patch[1] to address this so the logic will be easier to
test.
[1]: https://lore.kernel.org/lkml/20250801023358.562525-2-jstultz@google.com/
Fixes: a4f0b6fef4b0 ("locking/mutex: Add p->blocked_on wrappers for correctness checks")
Closes: https://lore.kernel.org/lkml/68894443.a00a0220.26d0e1.0015.GAE@google.com/
Reported-by: syzbot+602c4720aed62576cd79@syzkaller.appspotmail.com
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: K Prateek Nayak <kprateek.nayak@amd.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20250805001026.2247040-1-jstultz@google.com
In order to support future versions of the SVSM_CORE_PVALIDATE call, all
reserved fields within a PVALIDATE entry must be set to zero as an SVSM should
be ensuring all reserved fields are zero in order to support future usage of
reserved areas based on the protocol version.
Fixes: fcd042e86422 ("x86/sev: Perform PVALIDATE using the SVSM when not at VMPL0")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/7cde412f8b057ea13a646fb166b1ca023f6a5031.1755098819.git.thomas.lendacky@amd.com
The data->block[0] variable comes from user. Without proper check,
the variable may be very large to cause an out-of-bounds bug.
Fix this bug by checking the value of data->block[0] first.
1. commit 39244cc75482 ("i2c: ismt: Fix an out-of-bounds bug in
ismt_access()")
2. commit 92fbb6d1296f ("i2c: xgene-slimpro: Fix out-of-bounds bug in
xgene_slimpro_i2c_xfer()")
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Alex Guo <alexguo1023@gmail.com>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-1-cd9dca0db722@narfation.org
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 6.17-rc3 to resolve a bunch
of reported issues. Included in here are:
- typec driver fixes
- dwc3 new device id
- dwc3 driver fixes
- new usb-storage driver quirks
- xhci driver fixes
- other tiny USB driver fixes to resolve bugs
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: fix host not responding after suspend and resume
usb: xhci: Fix slot_id resource race conflict
usb: typec: fusb302: Revert incorrect threaded irq fix
USB: core: Update kerneldoc for usb_hcd_giveback_urb()
usb: typec: maxim_contaminant: re-enable cc toggle if cc is open and port is clean
usb: typec: maxim_contaminant: disable low power mode when reading comparator values
usb: dwc3: Remove WARN_ON for device endpoint command timeouts
USB: storage: Ignore driver CD mode for Realtek multi-mode Wi-Fi dongles
usb: storage: realtek_cr: Use correct byte order for bcs->Residue
usb: chipidea: imx: improve usbmisc_imx7d_pullup()
kcov, usb: Don't disable interrupts in kcov_remote_start_usb_softirq()
usb: dwc3: pci: add support for the Intel Wildcat Lake
usb: dwc3: Ignore late xferNotReady event to prevent halt timeout
USB: storage: Add unusual-devs entry for Novatek NTK96550-based camera
usb: core: hcd: fix accessing unmapped memory in SINGLE_STEP_SET_FEATURE test
usb: renesas-xhci: Fix External ROM access timeouts
usb: gadget: tegra-xudc: fix PM use count underflow
usb: quirks: Add DELAY_INIT quick for another SanDisk 3.2Gen1 Flash Drive
Jonathan writes:
IIO: 1st set of fixes for 6.17
Usual mixed bunch of ancient issues and relatively new ones.
adi,ad7124
- Fix channel lookup to use chan->address for indexing array.
adi,ad7173
- Stop accidentally enabling more configs than supported at one time.
adi,ad7380
- Fill in missing max_conversion_rate_hz for adaq4381-4
ams,as73211
- Fix uninitialized holes in scan data exposed to userspace.
bosch,bmp280
- Check for error when requesting optional GPIO rather than simply assuming
success or a NULL return when no GPIO provided.
invensense,icm42600
- Change error code returned to -EBUSY on a temperature read with neither
accelerometer nor gyroscope in use. Reduces chance of misinterpretation
by userspace.
kionix,sca3300
- Fix uninitialized holes in scan data exposed to userspace.
maxim,thermocouple
- Use a DMA-safe buffer for spi_read().
renesas,isl29501
- Fix ordering issue for big endian systems
renesas,rsg2l
- Fix an underflow issue around suspend/resume.
- Make sure driver data is in place before enabling runtime PM that uses
it.
rohm,bd79124
- Add missing GPIOLIB dependency. May rework in future to allow this to be
optional in future but for now this is the least invasive build fix.
* tag 'iio-fixes-for-6.17a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: pressure: bmp280: Use IS_ERR() in bmp280_common_probe()
iio: light: as73211: Ensure buffer holes are zeroed
iio: adc: rzg2l_adc: Set driver data before enabling runtime PM
iio: adc: rzg2l: Cleanup suspend/resume path
iio: adc: ad7380: fix missing max_conversion_rate_hz on adaq4381-4
iio: adc: bd79124: Add GPIOLIB dependency
iio: imu: inv_icm42600: change invalid data error to -EBUSY
iio: adc: ad7124: fix channel lookup in syscalib functions
iio: temperature: maxim_thermocouple: use DMA-safe buffer for spi_read()
iio: adc: ad7173: prevent scan if too many setups requested
iio: proximity: isl29501: fix buffered read on big-endian systems
iio: accel: sca3300: fix uninitialized iio scan data
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
takedown_cpu() has a comment about "all preempt/rcu users must observe
!cpu_active()" which is kind of meaningless in this function. This
comment was originally introduced by commit 6acce3ef8452 ("sched: Remove
get_online_cpus() usage") when _cpu_down() was setting cpu_active_mask
and synchronize_rcu()/synchronize_sched() were added after that.
Later commit 40190a78f85f ("sched/hotplug: Convert cpu_[in]active
notifiers to state machine") added a new CPUHP_AP_ACTIVE hotplug
state to set/clear cpu_active_mask. The following commit b2454caa8977
("sched/hotplug: Move sync_rcu to be with set_cpu_active(false)")
move the synchronize_*() calls to sched_cpu_deactivate() associated
with the new hotplug state, but left the comment behind.
Remove this comment as it is no longer relevant in takedown_cpu().
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250729191232.664931-1-longman@redhat.com
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Original-patch-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ata fixes from Damien Le Moal:
- Fix a regression affecting old IDE/PATA device scan and introduced by
the recent link power management cleanups & fixes. The regression
prevented devices from being properly detected (me)
- Fix command duration limits (CDL) feature control: attempting to
enable the feature while NCQ commands are being executed resulted in
a silent failure to enable CDL when needed (Igor)
* tag 'ata-ata-6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-scsi: Fix CDL control
ata: libata-eh: Fix link state check for IDE/PATA ports
`rustdoc` can get confused when generating documentation into a folder
that contains generated files from other `rustdoc` versions.
For instance, running something like:
rustup default 1.78.0
make LLVM=1 rustdoc
rustup default 1.88.0
make LLVM=1 rustdoc
may generate errors like:
error: couldn't generate documentation: invalid template: last line expected to start with a comment
|
= note: failed to create or modify "./Documentation/output/rust/rustdoc/src-files.js"
Thus just always clean the output folder before generating the
documentation -- we are anyway regenerating it every time the `rustdoc`
target gets called, at least for the time being.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Daniel Almeida <daniel.almeida@collabora.com>
Closes: https://rust-for-linux.zulipchat.com/#narrow/channel/288089/topic/x/near/527201113
Reviewed-by: Tamir Duberstein <tamird@kernel.org>
Link: https://lore.kernel.org/r/20250726133435.2460085-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Commit cec199c5e39b ("futex: Implement FUTEX2_NUMA") introduced the
futex_put_value() helper to write a value to the given user
address.
However, it uses user_read_access_begin() before the write. For
architectures that differentiate between read and write accesses, like
PowerPC, futex_put_value() fails with -EFAULT.
Fix that by using the user_write_access_begin/user_write_access_end() pair
instead.
Fixes: cec199c5e39b ("futex: Implement FUTEX2_NUMA")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250811141147.322261-1-longman@redhat.com
Commit
7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
added a check that requires the guest request buffers to be in the linear
mapping. The get_derived_key() function was passing a buffer that was
allocated on the stack, resulting in the call to snp_send_guest_request()
returning an error.
Update the get_derived_key() function to use an allocated buffer instead
of a stack buffer.
Fixes: 7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/9b764ca9fc79199a091aac684c4926e2080ca7a8.1752698495.git.thomas.lendacky@amd.com
Because Yicong Yang will no longer work on
i2c_hisi driver, update the maintainer
information for i2c_hisi.
Signed-off-by: Devyn Liu <liudingyuan@h-partners.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250819020349.4027842-1-liudingyuan@h-partners.com
Pull tracing fixes from Steven Rostedt:
- Fix rtla and latency tooling pkg-config errors
If libtraceevent and libtracefs is installed, but their corresponding
'.pc' files are not installed, it reports that the libraries are
missing and confuses the developer. Instead, report that the
pkg-config files are missing and should be installed.
- Fix overflow bug of the parser in trace_get_user()
trace_get_user() uses the parsing functions to parse the user space
strings. If the parser fails due to incorrect processing, it doesn't
terminate the buffer with a nul byte. Add a "failed" flag to the
parser that gets set when parsing fails and is used to know if the
buffer is fine to use or not.
- Remove a semicolon that was at an end of a comment line
- Fix register_ftrace_graph() to unregister the pm notifier on error
The register_ftrace_graph() registers a pm notifier but there's an
error path that can exit the function without unregistering it. Since
the function returns an error, it will never be unregistered.
- Allocate and copy ftrace hash for reader of ftrace filter files
When the set_ftrace_filter or set_ftrace_notrace files are open for
read, an iterator is created and sets its hash pointer to the
associated hash that represents filtering or notrace filtering to it.
The issue is that the hash it points to can change while the
iteration is happening. All the locking used to access the tracer's
hashes are released which means those hashes can change or even be
freed. Using the hash pointed to by the iterator can cause UAF bugs
or similar.
Have the read of these files allocate and copy the corresponding
hashes and use that as that will keep them the same while the
iterator is open. This also simplifies the code as opening it for
write already does an allocate and copy, and now that the read is
doing the same, there's no need to check which way it was opened on
the release of the file, and the iterator hash can always be freed.
- Fix function graph to copy args into temp storage
The output of the function graph tracer shows both the entry and the
exit of a function. When the exit is right after the entry, it
combines the two events into one with the output of "function();",
instead of showing:
function() {
}
In order to do this, the iterator descriptor that reads the events
includes storage that saves the entry event while it peaks at the
next event in the ring buffer. The peek can free the entry event so
the iterator must store the information to use it after the peek.
With the addition of function graph tracer recording the args, where
the args are a dynamic array in the entry event, the temp storage
does not save them. This causes the args to be corrupted or even
cause a read of unsafe memory.
Add space to save the args in the temp storage of the iterator.
- Fix race between ftrace_dump and reading trace_pipe
ftrace_dump() is used when a crash occurs where the ftrace buffer
will be printed to the console. But it can also be triggered by
sysrq-z. If a sysrq-z is triggered while a task is reading trace_pipe
it can cause a race in the ftrace_dump() where it checks if the
buffer has content, then it checks if the next event is available,
and then prints the output (regardless if the next event was
available or not). Reading trace_pipe at the same time can cause it
to not be available, and this triggers a WARN_ON in the print. Move
the printing into the check if the next event exists or not
* tag 'trace-v6.17-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ftrace: Also allocate and copy hash for reading of filter files
ftrace: Fix potential warning in trace_printk_seq during ftrace_dump
fgraph: Copy args in intermediate storage with entry
trace/fgraph: Fix the warning caused by missing unregister notifier
ring-buffer: Remove redundant semicolons
tracing: Limit access to parser->buffer when trace_get_user failed
rtla: Check pkg-config install
tools/latency-collector: Check pkg-config install
Partially revert commit e1db856bd288 ("usb: xhci: remove '0' write to
write-1-to-clear register") because the patch cleared the Interrupt Pending
bit during interrupt enabling and disabling. The Interrupt Pending bit
should only be cleared when the driver has handled the interrupt.
Ideally, all interrupts should be handled before disabling the interrupt;
consequently, no interrupt should be pending when enabling the interrupt.
For this reason, keep the debug message informing if an interrupt is still
pending when an interrupt is disabled.
Because the Interrupt Pending bit is write-1-to-clear, writing '0' to it
ensures that the state does not change.
Link: https://lore.kernel.org/linux-usb/20250818231103.672ec7ed@foxbook
Fixes: e1db856bd288 ("usb: xhci: remove '0' write to write-1-to-clear register")
Closes: https://bbs.archlinux.org/viewtopic.php?id=307641
cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In get_channel(), the reference obtained by bus_find_device_by_name()
was dropped via put_device() before accessing the device's driver data
Move put_device() after usage to avoid potential issues.
Fixes: 2485055394be ("staging: most: core: drop device reference")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250804082955.3621026-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`devm_gpiod_get_optional()` may return non-NULL error pointer on failure.
Check its return value using `IS_ERR()` and propagate the error if
necessary.
Fixes: df6e71256c84 ("iio: pressure: bmp280: Explicitly mark GPIO optional")
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250818092740.545379-2-salah.triki@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
0-day reported an off by one in the ioremap() sizing:
drivers/irqchip/irq-mvebu-gicp.c:240:45-48: WARNING:
Suspicious code. resource_size is maybe missing with gicp -> res
Convert it to resource_size(), which does the right thing.
Fixes: 3c3d7dbab2c7 ("irqchip/mvebu-gicp: Clear pending interrupts on init")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Closes: https://lore.kernel.org/oe-kbuild-all/202508062150.mtFQMTXc-lkp@intel.com/
"boolean" is spelt as "blooean". Fix that.
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250722161818.6139-1-romank@linux.microsoft.com
use a macro for PER_THREAD_PARAMS to make adding one later more clear.
no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
Pull SCSI fixes from James Bottomley:
"One core change removing the 'w' access flag of attributes that don't
have a set routine (and therefore can't be written to) which should
have no practical impact. The big scsi_debug update is caused by
reformatting lots of arrays and the rest of the bug fixes in drivers
are trivial"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove error print for devm_add_action_or_reset()
scsi: ufs: mediatek: Fix out-of-bounds access in MCQ IRQ mapping
scsi: lpfc: Remove redundant assignment to avoid memory leak
scsi: lpfc: Fix wrong function reference in a comment
scsi: ufs: core: Fix interrupt handling for MCQ Mode
scsi: scsi_debug: Make read-only arrays static const
scsi: core: sysfs: Correct sysfs attributes access rights
Delete extra checks for the ATA_DFLAG_CDL_ENABLED flag that prevent
SET FEATURES command from being issued to a drive when NCQ commands
are active.
ata_mselect_control_ata_feature() sets / clears the ATA_DFLAG_CDL_ENABLED
flag during the translation of MODE SELECT to SET FEATURES. If SET FEATURES
gets deferred due to outstanding NCQ commands, the original MODE SELECT
command will be re-queued. When the re-queued MODE SELECT goes through
the ata_mselect_control_ata_feature() translation again, SET FEATURES
will not be issued because ATA_DFLAG_CDL_ENABLED has been already set or
cleared by the initial translation of MODE SELECT.
The ATA_DFLAG_CDL_ENABLED checks in ata_mselect_control_ata_feature()
are safe to remove because scsi_cdl_enable() implements a similar logic
that avoids enabling CDL if it has been enabled already.
Fixes: 17e897a45675 ("ata: libata-scsi: Improve CDL control")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Starting with Rust 1.88.0 (released 2025-06-26), `rustdoc` complains
about a target modifier mismatch in configurations where `-Zfixed-x18`
is passed:
error: mixing `-Zfixed-x18` will cause an ABI mismatch in crate `rust_out`
|
= help: the `-Zfixed-x18` flag modifies the ABI so Rust crates compiled with different values of this flag cannot be used together safely
= note: unset `-Zfixed-x18` in this crate is incompatible with `-Zfixed-x18=` in dependency `core`
= help: set `-Zfixed-x18=` in this crate or unset `-Zfixed-x18` in `core`
= help: if you are sure this will not cause problems, you may use `-Cunsafe-allow-abi-mismatch=fixed-x18` to silence this error
The reason is that `rustdoc` was not passing the target modifiers when
configuring the session options, and thus it would report a mismatch
that did not exist as soon as a target modifier is used in a dependency.
We did not notice it in the kernel until now because `-Zfixed-x18` has
been a target modifier only since 1.88.0 (and it is the only one we use
so far).
The issue has been reported upstream [1] and a fix has been submitted
[2], including a test similar to the kernel case.
[ This is now fixed upstream (thanks Guillaume for the quick review),
so it will be fixed in Rust 1.90.0 (expected 2025-09-18).
- Miguel ]
Meanwhile, conditionally pass `-Cunsafe-allow-abi-mismatch=fixed-x18`
to workaround the issue on our side.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/rust-for-linux/36cdc798-524f-4910-8b77-d7b9fac08d77@oss.qualcomm.com/
Link: https://github.com/rust-lang/rust/issues/144521 [1]
Link: https://github.com/rust-lang/rust/pull/144523 [2]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250727092317.2930617-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Futex hash allocations are done in mm_init() and the cleanup happens in
__mmput(). That works most of the time, but there are mm instances which
are instantiated via mm_alloc() and freed via mmdrop(), which causes the
futex hash to be leaked.
Move the cleanup to __mmdrop().
Fixes: 56180dd20c19 ("futex: Use RCU-based per-CPU reference counting instead of rcuref_t")
Reported-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/all/87ldo5ihu0.ffs@tglx
Closes: https://lore.kernel.org/all/0c8cc83bb73abf080faf584f319008b67d0931db.camel@linaro.org
Currently, when a Secure TSC enabled SNP guest attempts to write to the
intercepted GUEST_TSC_FREQ MSR (a read-only MSR), the guest kernel response
incorrectly implies a VMM configuration error, when in fact it is the usual
VMM configuration to intercept writes to read-only MSRs, unless explicitly
documented.
Modify the intercepted TSC MSR #VC handling:
* Write to GUEST_TSC_FREQ will generate a #GP instead of terminating the
guest
* Write to MSR_IA32_TSC will generate a #GP instead of silently ignoring it
However, continue to terminate the guest when reading from intercepted
GUEST_TSC_FREQ MSR with Secure TSC enabled, as intercepted reads indicate an
improper VMM configuration for Secure TSC enabled SNP guests.
[ bp: simplify comment. ]
Fixes: 38cc6495cdec ("x86/sev: Prevent GUEST_TSC_FREQ MSR interception for Secure TSC enabled guests")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/20250722074853.22253-1-nikunj@amd.com
Pull driver core fixes from Danilo Krummrich:
- Fix swapped handling of lru_gen and lru_gen_full debugfs files in
vmscan
- Fix debugfs mount options (uid, gid, mode) being silently ignored
- Fix leak of devres action in the unwind path of Devres::new()
- Documentation:
- Expand and fix documentation of (outdated) Device, DeviceContext
and generic driver infrastructure
- Fix C header link of faux device abstractions
- Clarify expected interaction with the security team
- Smooth text flow in the security bug reporting process
documentation
* tag 'driver-core-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
Documentation: smooth the text flow in the security bug reporting process
Documentation: clarify the expected collaboration with security bugs reporters
debugfs: fix mount options not being applied
rust: devres: fix leaking call to devm_add_action()
rust: faux: fix C header link
driver: rust: expand documentation for driver infrastructure
device: rust: expand documentation for Device
device: rust: expand documentation for DeviceContext
mm/vmscan: fix inverted polarity in lru_gen_seq_show()
Currently the reader of set_ftrace_filter and set_ftrace_notrace just adds
the pointer to the global tracer hash to its iterator. Unlike the writer
that allocates a copy of the hash, the reader keeps the pointer to the
filter hashes. This is problematic because this pointer is static across
function calls that release the locks that can update the global tracer
hashes. This can cause UAF and similar bugs.
Allocate and copy the hash for reading the filter files like it is done
for the writers. This not only fixes UAF bugs, but also makes the code a
bit simpler as it doesn't have to differentiate when to free the
iterator's hash between writers and readers.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20250822183606.12962cc3@batman.local.home
Fixes: c20489dad156 ("ftrace: Assign iter->hash to filter or notrace hashes on seq read")
Closes: https://lore.kernel.org/all/20250813023044.2121943-1-wutengda@huaweicloud.com/
Closes: https://lore.kernel.org/all/20250822192437.GA458494@ax162/
Reported-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953ed1 ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_rw_emulate_bits()` function is used as a default handler for
`INSN_READ` instructions for subdevices that have a handler for
`INSN_BITS` but not for `INSN_READ`. Similarly, it is used as a default
handler for `INSN_WRITE` instructions for subdevices that have a handler
for `INSN_BITS` but not for `INSN_WRITE`. It works by emulating the
`INSN_READ` or `INSN_WRITE` instruction handling with a constructed
`INSN_BITS` instruction. However, `INSN_READ` and `INSN_WRITE`
instructions are supposed to be able read or write multiple samples,
indicated by the `insn->n` value, but `insn_rw_emulate_bits()` currently
only handles a single sample. For `INSN_READ`, the comedi core will
copy `insn->n` samples back to user-space. (That triggered KASAN
kernel-infoleak errors when `insn->n` was greater than 1, but that is
being fixed more generally elsewhere in the comedi core.)
Make `insn_rw_emulate_bits()` either handle `insn->n` samples, or return
an error, to conform to the general expectation for `INSN_READ` and
`INSN_WRITE` handlers.
Fixes: ed9eccbe8970 ("Staging: add comedi core")
Cc: stable <stable@kernel.org> # 5.13+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20250725141034.87297-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given that the buffer is copied to a kfifo that ultimately user space
can read, ensure we zero it.
Fixes: 403e5586b52e ("iio: light: as73211: New driver")
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250802164436.515988-2-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull locking fix from Borislav Petkov:
- Prevent a futex hash leak due to different mm lifetimes
* tag 'locking_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Move futex cleanup to __mmdrop()
Hogan reported a vector setup race, which overwrites the interrupt
descriptor in the per CPU vector array resulting in a disfunctional device.
CPU0 CPU1
interrupt is raised in APIC IRR
but not handled
free_irq()
per_cpu(vector_irq, CPU1)[vector] = VECTOR_SHUTDOWN;
request_irq() common_interrupt()
d = this_cpu_read(vector_irq[vector]);
per_cpu(vector_irq, CPU1)[vector] = desc;
if (d == VECTOR_SHUTDOWN)
this_cpu_write(vector_irq[vector], VECTOR_UNUSED);
free_irq() cannot observe the pending vector in the CPU1 APIC as there is
no way to query the remote CPUs APIC IRR.
This requires that request_irq() uses the same vector/CPU as the one which
was freed, but this also can be triggered by a spurious interrupt.
Interestingly enough this problem managed to be hidden for more than a
decade.
Prevent this by reevaluating vector_irq under the vector lock, which is
held by the interrupt activation code when vector_irq is updated.
To avoid ifdeffery or IS_ENABLED() nonsense, move the
[un]lock_vector_lock() declarations out under the
CONFIG_IRQ_DOMAIN_HIERARCHY guard as it's only provided when
CONFIG_X86_LOCAL_APIC=y.
The current CONFIG_IRQ_DOMAIN_HIERARCHY guard is selected by
CONFIG_X86_LOCAL_APIC, but can also be selected by other parts of the
Kconfig system, which makes 32-bit UP builds with CONFIG_X86_LOCAL_APIC=n
fail.
Can we just get rid of this !APIC nonsense once and forever?
Fixes: 9345005f4eed ("x86/irq: Fix do_IRQ() interrupt warning for cpu hotplug retriggered irqs")
Reported-by: Hogan Wang <hogan.wang@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hogan Wang <hogan.wang@huawei.com>
Link: https://lore.kernel.org/all/draft-87ikjhrhhh.ffs@tglx
Pull i2c fixes from Wolfram Sang:
- hisi: update maintainership
- fix several issues in rtl9300 xfer:
- check message length boundaries
- correct multi-byte value composition on write
- increase polling timeout
- fix block transfer protocol
* tag 'i2c-for-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rtl9300: Add missing count byte for SMBus Block Ops
i2c: rtl9300: Increase timeout for transfer polling
i2c: rtl9300: Fix multi-byte I2C write
i2c: rtl9300: Fix out-of-bounds bug in rtl9300_i2c_smbus_xfer
MAINTAINERS: i2c: Update i2c_hisi entry
Pull x86 fixes from Borislav Petkov:
- Fix the GDS mitigation detection on some machines after the recent
attack vectors conversion
- Filter out the invalid machine reset reason value -1 when running as
a guest as in such cases the reason why the machine was rebooted does
not make a whole lot of sense
- Init the resource control machinery on Hygon hw in order to avoid a
division by zero and to actually enable the feature on hw which
supports it
* tag 'x86_urgent_for_v6.17_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Fix GDS mitigation selecting when mitigation is off
x86/CPU/AMD: Ignore invalid reset reason value
x86/cpu/hygon: Add missing resctrl_cpu_detect() in bsp_init helper
Calling pmu->start()/stop() on perf events in PERF_EVENT_STATE_OFF can
leave event->hw.idx at -1. When PMU drivers later attempt to use this
negative index as a shift exponent in bitwise operations, it leads to UBSAN
shift-out-of-bounds reports.
The issue is a logical flaw in how event groups handle throttling when some
members are intentionally disabled. Based on the analysis and the
reproducer provided by Mark Rutland (this issue on both arm64 and x86-64).
The scenario unfolds as follows:
1. A group leader event is configured with a very aggressive sampling
period (e.g., sample_period = 1). This causes frequent interrupts and
triggers the throttling mechanism.
2. A child event in the same group is created in a disabled state
(.disabled = 1). This event remains in PERF_EVENT_STATE_OFF.
Since it hasn't been scheduled onto the PMU, its event->hw.idx remains
initialized at -1.
3. When throttling occurs, perf_event_throttle_group() and later
perf_event_unthrottle_group() iterate through all siblings, including
the disabled child event.
4. perf_event_throttle()/unthrottle() are called on this inactive child
event, which then call event->pmu->start()/stop().
5. The PMU driver receives the event with hw.idx == -1 and attempts to
use it as a shift exponent. e.g., in macros like PMCNTENSET(idx),
leading to the UBSAN report.
The throttling mechanism attempts to start/stop events that are not
actively scheduled on the hardware.
Move the state check into perf_event_throttle()/perf_event_unthrottle() so
that inactive events are skipped entirely. This ensures only active events
with a valid hw.idx are processed, preventing undefined behavior and
silencing UBSAN warnings. The corrected check ensures true before
proceeding with PMU operations.
The problem can be reproduced with the syzkaller reproducer:
Fixes: 9734e25fbf5a ("perf: Fix the throttle logic for a group")
Signed-off-by: Yunseong Kim <ysk@kzalloc.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20250812181046.292382-2-ysk@kzalloc.com
The expected on-wire format of an SMBus Block Write is
S Addr Wr [A] Comm [A] Count [A] Data [A] Data [A] ... [A] Data [A] P
Everything starting from the Count byte is provided by the I2C subsystem in
the array data->block. But the driver was skipping the Count byte
(data->block[0]) when sending it to the RTL93xx I2C controller.
Only the actual data could be seen on the wire:
S Addr Wr [A] Comm [A] Data [A] Data [A] ... [A] Data [A] P
This wire format is not SMBus Block Write compatible but matches the format
of an I2C Block Write. Simply adding the count byte to the buffer for the
I2C controller is enough to fix the transmission.
This also affects read because the I2C controller must receive the count
byte + $count * data bytes.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-4-cd9dca0db722@narfation.org
The current GDS mitigation logic incorrectly returns early when the
attack vector mitigation is turned off, which leads to two problems:
1. CPUs without ARCH_CAP_GDS_CTRL support are incorrectly marked with
GDS_MITIGATION_OFF when they should be marked as
GDS_MITIGATION_UCODE_NEEDED.
2. The mitigation state checks and locking verification that follow are
skipped, which means:
- fail to detect if the mitigation was locked
- miss the warning when trying to disable a locked mitigation
Remove the early return to ensure proper mitigation state handling. This
allows:
- Proper mitigation classification for non-ARCH_CAP_GDS_CTRL CPUs
- Complete mitigation state verification
This also addresses the failed MSR 0x123 write attempt at boot on
non-ARCH_CAP_GDS_CTRL CPUs:
unchecked MSR access error: WRMSR to 0x123 (tried to write 0x0000000000000010) at rIP: ... (update_gds_msr)
Call Trace:
identify_secondary_cpu
start_secondary
common_startup_64
WARNING: CPU: 1 PID: 0 at arch/x86/kernel/cpu/bugs.c:1053 update_gds_msr
[ bp: Massage, zap superfluous braces. ]
Fixes: 8c7261abcb7ad ("x86/bugs: Add attack vector controls for GDS")
Suggested-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Link: https://lore.kernel.org/20250819023356.2012-1-lirongqing@baidu.com
Pull x86 fixes from Borislav Petkov:
- Remove a transitional asm/cpuid.h header which was added only as a
fallback during cpuid helpers reorg
- Initialize reserved fields in the SVSM page validation calls
structure to zero in order to allow for future structure extensions
- Have the sev-guest driver's buffers used in encryption operations be
in linear mapping space as the encryption operation can be offloaded
to an accelerator
- Have a read-only MSR write when in an AMD SNP guest trap to the
hypervisor as it is usually done. This makes the guest user
experience better by simply raising a #GP instead of terminating said
guest
- Do not output AVX512 elapsed time for kernel threads because the data
is wrong and fix a NULL pointer dereferencing in the process
- Adjust the SRSO mitigation selection to the new attack vectors
* tag 'x86_urgent_for_v6.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpuid: Remove transitional <asm/cpuid.h> header
x86/sev: Ensure SVSM reserved fields in a page validation entry are initialized to zero
virt: sev-guest: Satisfy linear mapping requirement in get_derived_key()
x86/sev: Improve handling of writes to intercepted TSC MSRs
x86/fpu: Fix NULL dereference in avx512_status()
x86/bugs: Select best SRSO mitigation
The timeout for transfers was only set to 2ms. Because of this relatively
low limit, 12-byte read operations to the frontend MCU of a RTL8239 POE PSE
chip cluster was consistently resulting in a timeout.
The original OpenWrt downstream driver [1] was not using any timeout limit
at all. This is also possible by setting the timeout_us parameter of
regmap_read_poll_timeout() to 0. But since the driver currently implements
the ETIMEDOUT error, it is more sensible to increase the timeout in such a
way that communication with the (quite common) Realtek I2C-connected POE
management solution is possible.
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-6.12/drivers/i2c/busses/i2c-rtl9300.c;h=c4d973195ef39dc56d6207e665d279745525fcac#l202
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-3-cd9dca0db722@narfation.org
Pull modules fix from Daniel Gomez:
"This includes a fix part of the KSPP (Kernel Self Protection Project)
to replace the deprecated and unsafe strcpy() calls in the kernel
parameter string handler and sysfs parameters for built-in modules.
Single commit, no functional changes"
* tag 'modules-6.17-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux:
params: Replace deprecated strcpy() with strscpy() and memcpy()
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad93741 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
The reset reason value may be "all bits set", e.g. 0xFFFFFFFF. This is a
commonly used error response from hardware. This may occur due to a real
hardware issue or when running in a VM.
The user will see all reset reasons reported in this case.
Check for an error response value and return early to avoid decoding
invalid data.
Also, adjust the data variable type to match the hardware register size.
Fixes: ab8131028710 ("x86/CPU/AMD: Print the reason for the last reset")
Reported-by: Libing He <libhe@redhat.com>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250721181155.3536023-1-yazen.ghannam@amd.com
Pull turbostat updates from Len Brown:
"tools/power turbostat: version 2025.09.09
- Probe and display L3 Cache topology
- Add ability to average an added counter (useful for pre-integrated
"counters", such as Watts)
- Break the limit of 64 built-in counters
- Assorted bug fixes and minor feature tweaks"
* tag 'turbostat-2025.09.09' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2025.09.09
tools/power turbostat: Handle non-root legacy-uncore sysfs permissions
tools/power turbostat: standardize PER_THREAD_PARAMS
tools/power turbostat: Fix DMR support
tools/power turbostat: add format "average" for external attributes
tools/power turbostat: delete GET_PKG()
tools/power turbostat: probe and display L3 cache topology
tools/power turbostat: Support more than 64 built-in-counters
tools/power turbostat.8: Document Totl%C0, Any%C0, GFX%C0, CPUGFX% columns
tools/power turbostat: Fix bogus SysWatt for forked program
tools/power turbostat: Handle cap_get_proc() ENOSYS
tools/power turbostat: Fix build with musl
tools/power turbostat: verify arguments to params --show and --hide
tools/power turbostat: regression fix: --show C1E%
Pull locking fixes from Borislav Petkov:
- Make sure sanity checks down in the mutex lock path happen on the
correct type of task so that they don't trigger falsely
- Use the write unsafe user access pairs when writing a futex value to
prevent an error on PowerPC which does user read and write accesses
differently
* tag 'locking_urgent_for_v6.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking: Fix __clear_task_blocked_on() warning from __ww_mutex_wound() path
futex: Use user_write_access_begin/_end() in futex_put_value()
All CPUID call sites were updated at commit:
968e30006807 ("x86/cpuid: Set <asm/cpuid/api.h> as the main CPUID header")
to include <asm/cpuid/api.h> instead of <asm/cpuid.h>.
The <asm/cpuid.h> header was still retained as a wrapper, just in case
some new code in -next started using it. Now that everything is merged
to Linus' tree, remove the header.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250815070227.19981-2-darwi@linutronix.de
The RTL93xx I2C controller has 4 32 bit registers to store the bytes for
the upcoming I2C transmission. The first byte is stored in the
least-significant byte of the first register. And the last byte in the most
significant byte of the last register. A map of the transferred bytes to
their order in the registers is:
reg 0: 0x04_03_02_01
reg 1: 0x08_07_06_05
reg 2: 0x0c_0b_0a_09
reg 3: 0x10_0f_0e_0d
The i2c_read() function basically demonstrates how the hardware would pick
up bytes from this register set. But the i2c_write() function was just
pushing bytes one after another to the least significant byte of a register
AFTER shifting the last one to the next more significant byte position.
If you would then have tried to send a buffer with numbers 1-11 using
i2c_write(), you would have ended up with following register content:
reg 0: 0x01_02_03_04
reg 1: 0x05_06_07_08
reg 2: 0x00_09_0a_0b
reg 3: 0x00_00_00_00
On the wire, you would then have seen:
Sr Addr Wr [A] 04 A 03 A 02 A 01 A 08 A 07 A 06 A 05 A 0b A 0a A 09 A P
But the correct data transmission was expected to be
Sr Addr Wr [A] 01 A 02 A 03 A 04 A 05 A 06 A 07 A 08 A 09 A 0a A 0b A P
Because of this multi-byte ordering problem, only single byte i2c_write()
operations were executed correctly (on the wire).
By shifting the byte directly to the correct end position in the register,
it is possible to avoid this incorrect byte ordering and fix multi-byte
transmissions.
The second initialization (to 0) of vals was also be dropped because this
array is initialized to 0 on the stack by using `= {};`. This makes the
fix a lot more readable.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Cc: <stable@vger.kernel.org> # v6.13+
Co-developed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-2-cd9dca0db722@narfation.org
Pull char/misc/iio fixes from Greg KH:
"Here are a small number of char/misc/iio and other driver fixes for
6.17-rc3. Included in here are:
- IIO driver bugfixes for reported issues
- bunch of comedi driver fixes
- most core bugfix
- fpga driver bugfix
- cdx driver bugfix
All of these have been in linux-next this week with no reported
issues"
* tag 'char-misc-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
most: core: Drop device reference after usage in get_channel()
comedi: Make insn_rw_emulate_bits() do insn->n samples
comedi: Fix use of uninitialized memory in do_insn_ioctl() and do_insnlist_ioctl()
comedi: pcl726: Prevent invalid irq number
cdx: Fix off-by-one error in cdx_rpmsg_probe()
fpga: zynq_fpga: Fix the wrong usage of dma_map_sgtable()
iio: pressure: bmp280: Use IS_ERR() in bmp280_common_probe()
iio: light: as73211: Ensure buffer holes are zeroed
iio: adc: rzg2l_adc: Set driver data before enabling runtime PM
iio: adc: rzg2l: Cleanup suspend/resume path
iio: adc: ad7380: fix missing max_conversion_rate_hz on adaq4381-4
iio: adc: bd79124: Add GPIOLIB dependency
iio: imu: inv_icm42600: change invalid data error to -EBUSY
iio: adc: ad7124: fix channel lookup in syscalib functions
iio: temperature: maxim_thermocouple: use DMA-safe buffer for spi_read()
iio: adc: ad7173: prevent scan if too many setups requested
iio: proximity: isl29501: fix buffered read on big-endian systems
iio: accel: sca3300: fix uninitialized iio scan data
strcpy() is deprecated; use strscpy() and memcpy() instead.
In param_set_copystring(), we can safely use memcpy() because we already
know the length of the source string 'val' and that it is guaranteed to
be NUL-terminated within the first 'kps->maxlen' bytes.
Link: https://github.com/KSPP/linux/issues/88
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Link: https://lore.kernel.org/r/20250813132200.184064-2-thorsten.blum@linux.dev
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0aa ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Since
923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot")
resctrl_cpu_detect() has been moved from common CPU initialization code to
the vendor-specific BSP init helper, while Hygon didn't put that call in their
code.
This triggers a division by zero fault during early booting stage on our
machines with X86_FEATURE_CQM* supported, where get_rdt_mon_resources() tries
to calculate mon_l3_config with uninitialized boot_cpu_data.x86_cache_occ_scale.
Add the missing resctrl_cpu_detect() in the Hygon BSP init helper.
[ bp: Massage commit message. ]
Fixes: 923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot")
Signed-off-by: Tianxiang Peng <txpeng@tencent.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Hui Li <caelli@tencent.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/20250623093153.3016937-1-txpeng@tencent.com
Pull rust fixes from Miguel Ojeda:
- Workaround 'rustdoc' target modifiers bug in Rust >= 1.88.0. It will
be fixed in Rust 1.90.0 (expected 2025-09-18).
- Clean 'rustdoc' output before running it to avoid confusing the tool
when files from previous versions remain.
* tag 'rust-fixes-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: kbuild: clean output before running `rustdoc`
rust: workaround `rustdoc` target modifiers bug
The __clear_task_blocked_on() helper added a number of sanity
checks ensuring we hold the mutex wait lock and that the task
we are clearing blocked_on pointer (if set) matches the mutex.
However, there is an edge case in the _ww_mutex_wound() logic
where we need to clear the blocked_on pointer for the task that
owns the mutex, not the task that is waiting on the mutex.
For this case the sanity checks aren't valid, so handle this
by allowing a NULL lock to skip the additional checks.
K Prateek Nayak and Maarten Lankhorst also pointed out that in
this case where we don't hold the owner's mutex wait_lock, we
need to be a bit more careful using READ_ONCE/WRITE_ONCE in both
the __clear_task_blocked_on() and __set_task_blocked_on()
implementations to avoid accidentally tripping WARN_ONs if two
instances race. So do that here as well.
This issue was easier to miss, I realized, as the test-ww_mutex
driver only exercises the wait-die class of ww_mutexes. I've
sent a patch[1] to address this so the logic will be easier to
test.
[1]: https://lore.kernel.org/lkml/20250801023358.562525-2-jstultz@google.com/
Fixes: a4f0b6fef4b0 ("locking/mutex: Add p->blocked_on wrappers for correctness checks")
Closes: https://lore.kernel.org/lkml/68894443.a00a0220.26d0e1.0015.GAE@google.com/
Reported-by: syzbot+602c4720aed62576cd79@syzkaller.appspotmail.com
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: K Prateek Nayak <kprateek.nayak@amd.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20250805001026.2247040-1-jstultz@google.com
In order to support future versions of the SVSM_CORE_PVALIDATE call, all
reserved fields within a PVALIDATE entry must be set to zero as an SVSM should
be ensuring all reserved fields are zero in order to support future usage of
reserved areas based on the protocol version.
Fixes: fcd042e86422 ("x86/sev: Perform PVALIDATE using the SVSM when not at VMPL0")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/7cde412f8b057ea13a646fb166b1ca023f6a5031.1755098819.git.thomas.lendacky@amd.com
The data->block[0] variable comes from user. Without proper check,
the variable may be very large to cause an out-of-bounds bug.
Fix this bug by checking the value of data->block[0] first.
1. commit 39244cc75482 ("i2c: ismt: Fix an out-of-bounds bug in
ismt_access()")
2. commit 92fbb6d1296f ("i2c: xgene-slimpro: Fix out-of-bounds bug in
xgene_slimpro_i2c_xfer()")
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Alex Guo <alexguo1023@gmail.com>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-1-cd9dca0db722@narfation.org
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 6.17-rc3 to resolve a bunch
of reported issues. Included in here are:
- typec driver fixes
- dwc3 new device id
- dwc3 driver fixes
- new usb-storage driver quirks
- xhci driver fixes
- other tiny USB driver fixes to resolve bugs
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: fix host not responding after suspend and resume
usb: xhci: Fix slot_id resource race conflict
usb: typec: fusb302: Revert incorrect threaded irq fix
USB: core: Update kerneldoc for usb_hcd_giveback_urb()
usb: typec: maxim_contaminant: re-enable cc toggle if cc is open and port is clean
usb: typec: maxim_contaminant: disable low power mode when reading comparator values
usb: dwc3: Remove WARN_ON for device endpoint command timeouts
USB: storage: Ignore driver CD mode for Realtek multi-mode Wi-Fi dongles
usb: storage: realtek_cr: Use correct byte order for bcs->Residue
usb: chipidea: imx: improve usbmisc_imx7d_pullup()
kcov, usb: Don't disable interrupts in kcov_remote_start_usb_softirq()
usb: dwc3: pci: add support for the Intel Wildcat Lake
usb: dwc3: Ignore late xferNotReady event to prevent halt timeout
USB: storage: Add unusual-devs entry for Novatek NTK96550-based camera
usb: core: hcd: fix accessing unmapped memory in SINGLE_STEP_SET_FEATURE test
usb: renesas-xhci: Fix External ROM access timeouts
usb: gadget: tegra-xudc: fix PM use count underflow
usb: quirks: Add DELAY_INIT quick for another SanDisk 3.2Gen1 Flash Drive
Jonathan writes:
IIO: 1st set of fixes for 6.17
Usual mixed bunch of ancient issues and relatively new ones.
adi,ad7124
- Fix channel lookup to use chan->address for indexing array.
adi,ad7173
- Stop accidentally enabling more configs than supported at one time.
adi,ad7380
- Fill in missing max_conversion_rate_hz for adaq4381-4
ams,as73211
- Fix uninitialized holes in scan data exposed to userspace.
bosch,bmp280
- Check for error when requesting optional GPIO rather than simply assuming
success or a NULL return when no GPIO provided.
invensense,icm42600
- Change error code returned to -EBUSY on a temperature read with neither
accelerometer nor gyroscope in use. Reduces chance of misinterpretation
by userspace.
kionix,sca3300
- Fix uninitialized holes in scan data exposed to userspace.
maxim,thermocouple
- Use a DMA-safe buffer for spi_read().
renesas,isl29501
- Fix ordering issue for big endian systems
renesas,rsg2l
- Fix an underflow issue around suspend/resume.
- Make sure driver data is in place before enabling runtime PM that uses
it.
rohm,bd79124
- Add missing GPIOLIB dependency. May rework in future to allow this to be
optional in future but for now this is the least invasive build fix.
* tag 'iio-fixes-for-6.17a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: pressure: bmp280: Use IS_ERR() in bmp280_common_probe()
iio: light: as73211: Ensure buffer holes are zeroed
iio: adc: rzg2l_adc: Set driver data before enabling runtime PM
iio: adc: rzg2l: Cleanup suspend/resume path
iio: adc: ad7380: fix missing max_conversion_rate_hz on adaq4381-4
iio: adc: bd79124: Add GPIOLIB dependency
iio: imu: inv_icm42600: change invalid data error to -EBUSY
iio: adc: ad7124: fix channel lookup in syscalib functions
iio: temperature: maxim_thermocouple: use DMA-safe buffer for spi_read()
iio: adc: ad7173: prevent scan if too many setups requested
iio: proximity: isl29501: fix buffered read on big-endian systems
iio: accel: sca3300: fix uninitialized iio scan data
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
takedown_cpu() has a comment about "all preempt/rcu users must observe
!cpu_active()" which is kind of meaningless in this function. This
comment was originally introduced by commit 6acce3ef8452 ("sched: Remove
get_online_cpus() usage") when _cpu_down() was setting cpu_active_mask
and synchronize_rcu()/synchronize_sched() were added after that.
Later commit 40190a78f85f ("sched/hotplug: Convert cpu_[in]active
notifiers to state machine") added a new CPUHP_AP_ACTIVE hotplug
state to set/clear cpu_active_mask. The following commit b2454caa8977
("sched/hotplug: Move sync_rcu to be with set_cpu_active(false)")
move the synchronize_*() calls to sched_cpu_deactivate() associated
with the new hotplug state, but left the comment behind.
Remove this comment as it is no longer relevant in takedown_cpu().
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250729191232.664931-1-longman@redhat.com
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Original-patch-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ata fixes from Damien Le Moal:
- Fix a regression affecting old IDE/PATA device scan and introduced by
the recent link power management cleanups & fixes. The regression
prevented devices from being properly detected (me)
- Fix command duration limits (CDL) feature control: attempting to
enable the feature while NCQ commands are being executed resulted in
a silent failure to enable CDL when needed (Igor)
* tag 'ata-ata-6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-scsi: Fix CDL control
ata: libata-eh: Fix link state check for IDE/PATA ports
`rustdoc` can get confused when generating documentation into a folder
that contains generated files from other `rustdoc` versions.
For instance, running something like:
rustup default 1.78.0
make LLVM=1 rustdoc
rustup default 1.88.0
make LLVM=1 rustdoc
may generate errors like:
error: couldn't generate documentation: invalid template: last line expected to start with a comment
|
= note: failed to create or modify "./Documentation/output/rust/rustdoc/src-files.js"
Thus just always clean the output folder before generating the
documentation -- we are anyway regenerating it every time the `rustdoc`
target gets called, at least for the time being.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Daniel Almeida <daniel.almeida@collabora.com>
Closes: https://rust-for-linux.zulipchat.com/#narrow/channel/288089/topic/x/near/527201113
Reviewed-by: Tamir Duberstein <tamird@kernel.org>
Link: https://lore.kernel.org/r/20250726133435.2460085-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Commit cec199c5e39b ("futex: Implement FUTEX2_NUMA") introduced the
futex_put_value() helper to write a value to the given user
address.
However, it uses user_read_access_begin() before the write. For
architectures that differentiate between read and write accesses, like
PowerPC, futex_put_value() fails with -EFAULT.
Fix that by using the user_write_access_begin/user_write_access_end() pair
instead.
Fixes: cec199c5e39b ("futex: Implement FUTEX2_NUMA")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250811141147.322261-1-longman@redhat.com
Commit
7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
added a check that requires the guest request buffers to be in the linear
mapping. The get_derived_key() function was passing a buffer that was
allocated on the stack, resulting in the call to snp_send_guest_request()
returning an error.
Update the get_derived_key() function to use an allocated buffer instead
of a stack buffer.
Fixes: 7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/9b764ca9fc79199a091aac684c4926e2080ca7a8.1752698495.git.thomas.lendacky@amd.com
Because Yicong Yang will no longer work on
i2c_hisi driver, update the maintainer
information for i2c_hisi.
Signed-off-by: Devyn Liu <liudingyuan@h-partners.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250819020349.4027842-1-liudingyuan@h-partners.com
Pull tracing fixes from Steven Rostedt:
- Fix rtla and latency tooling pkg-config errors
If libtraceevent and libtracefs is installed, but their corresponding
'.pc' files are not installed, it reports that the libraries are
missing and confuses the developer. Instead, report that the
pkg-config files are missing and should be installed.
- Fix overflow bug of the parser in trace_get_user()
trace_get_user() uses the parsing functions to parse the user space
strings. If the parser fails due to incorrect processing, it doesn't
terminate the buffer with a nul byte. Add a "failed" flag to the
parser that gets set when parsing fails and is used to know if the
buffer is fine to use or not.
- Remove a semicolon that was at an end of a comment line
- Fix register_ftrace_graph() to unregister the pm notifier on error
The register_ftrace_graph() registers a pm notifier but there's an
error path that can exit the function without unregistering it. Since
the function returns an error, it will never be unregistered.
- Allocate and copy ftrace hash for reader of ftrace filter files
When the set_ftrace_filter or set_ftrace_notrace files are open for
read, an iterator is created and sets its hash pointer to the
associated hash that represents filtering or notrace filtering to it.
The issue is that the hash it points to can change while the
iteration is happening. All the locking used to access the tracer's
hashes are released which means those hashes can change or even be
freed. Using the hash pointed to by the iterator can cause UAF bugs
or similar.
Have the read of these files allocate and copy the corresponding
hashes and use that as that will keep them the same while the
iterator is open. This also simplifies the code as opening it for
write already does an allocate and copy, and now that the read is
doing the same, there's no need to check which way it was opened on
the release of the file, and the iterator hash can always be freed.
- Fix function graph to copy args into temp storage
The output of the function graph tracer shows both the entry and the
exit of a function. When the exit is right after the entry, it
combines the two events into one with the output of "function();",
instead of showing:
function() {
}
In order to do this, the iterator descriptor that reads the events
includes storage that saves the entry event while it peaks at the
next event in the ring buffer. The peek can free the entry event so
the iterator must store the information to use it after the peek.
With the addition of function graph tracer recording the args, where
the args are a dynamic array in the entry event, the temp storage
does not save them. This causes the args to be corrupted or even
cause a read of unsafe memory.
Add space to save the args in the temp storage of the iterator.
- Fix race between ftrace_dump and reading trace_pipe
ftrace_dump() is used when a crash occurs where the ftrace buffer
will be printed to the console. But it can also be triggered by
sysrq-z. If a sysrq-z is triggered while a task is reading trace_pipe
it can cause a race in the ftrace_dump() where it checks if the
buffer has content, then it checks if the next event is available,
and then prints the output (regardless if the next event was
available or not). Reading trace_pipe at the same time can cause it
to not be available, and this triggers a WARN_ON in the print. Move
the printing into the check if the next event exists or not
* tag 'trace-v6.17-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ftrace: Also allocate and copy hash for reading of filter files
ftrace: Fix potential warning in trace_printk_seq during ftrace_dump
fgraph: Copy args in intermediate storage with entry
trace/fgraph: Fix the warning caused by missing unregister notifier
ring-buffer: Remove redundant semicolons
tracing: Limit access to parser->buffer when trace_get_user failed
rtla: Check pkg-config install
tools/latency-collector: Check pkg-config install
Partially revert commit e1db856bd288 ("usb: xhci: remove '0' write to
write-1-to-clear register") because the patch cleared the Interrupt Pending
bit during interrupt enabling and disabling. The Interrupt Pending bit
should only be cleared when the driver has handled the interrupt.
Ideally, all interrupts should be handled before disabling the interrupt;
consequently, no interrupt should be pending when enabling the interrupt.
For this reason, keep the debug message informing if an interrupt is still
pending when an interrupt is disabled.
Because the Interrupt Pending bit is write-1-to-clear, writing '0' to it
ensures that the state does not change.
Link: https://lore.kernel.org/linux-usb/20250818231103.672ec7ed@foxbook
Fixes: e1db856bd288 ("usb: xhci: remove '0' write to write-1-to-clear register")
Closes: https://bbs.archlinux.org/viewtopic.php?id=307641
cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In get_channel(), the reference obtained by bus_find_device_by_name()
was dropped via put_device() before accessing the device's driver data
Move put_device() after usage to avoid potential issues.
Fixes: 2485055394be ("staging: most: core: drop device reference")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250804082955.3621026-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`devm_gpiod_get_optional()` may return non-NULL error pointer on failure.
Check its return value using `IS_ERR()` and propagate the error if
necessary.
Fixes: df6e71256c84 ("iio: pressure: bmp280: Explicitly mark GPIO optional")
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250818092740.545379-2-salah.triki@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
0-day reported an off by one in the ioremap() sizing:
drivers/irqchip/irq-mvebu-gicp.c:240:45-48: WARNING:
Suspicious code. resource_size is maybe missing with gicp -> res
Convert it to resource_size(), which does the right thing.
Fixes: 3c3d7dbab2c7 ("irqchip/mvebu-gicp: Clear pending interrupts on init")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Closes: https://lore.kernel.org/oe-kbuild-all/202508062150.mtFQMTXc-lkp@intel.com/
Pull SCSI fixes from James Bottomley:
"One core change removing the 'w' access flag of attributes that don't
have a set routine (and therefore can't be written to) which should
have no practical impact. The big scsi_debug update is caused by
reformatting lots of arrays and the rest of the bug fixes in drivers
are trivial"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove error print for devm_add_action_or_reset()
scsi: ufs: mediatek: Fix out-of-bounds access in MCQ IRQ mapping
scsi: lpfc: Remove redundant assignment to avoid memory leak
scsi: lpfc: Fix wrong function reference in a comment
scsi: ufs: core: Fix interrupt handling for MCQ Mode
scsi: scsi_debug: Make read-only arrays static const
scsi: core: sysfs: Correct sysfs attributes access rights
Delete extra checks for the ATA_DFLAG_CDL_ENABLED flag that prevent
SET FEATURES command from being issued to a drive when NCQ commands
are active.
ata_mselect_control_ata_feature() sets / clears the ATA_DFLAG_CDL_ENABLED
flag during the translation of MODE SELECT to SET FEATURES. If SET FEATURES
gets deferred due to outstanding NCQ commands, the original MODE SELECT
command will be re-queued. When the re-queued MODE SELECT goes through
the ata_mselect_control_ata_feature() translation again, SET FEATURES
will not be issued because ATA_DFLAG_CDL_ENABLED has been already set or
cleared by the initial translation of MODE SELECT.
The ATA_DFLAG_CDL_ENABLED checks in ata_mselect_control_ata_feature()
are safe to remove because scsi_cdl_enable() implements a similar logic
that avoids enabling CDL if it has been enabled already.
Fixes: 17e897a45675 ("ata: libata-scsi: Improve CDL control")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Starting with Rust 1.88.0 (released 2025-06-26), `rustdoc` complains
about a target modifier mismatch in configurations where `-Zfixed-x18`
is passed:
error: mixing `-Zfixed-x18` will cause an ABI mismatch in crate `rust_out`
|
= help: the `-Zfixed-x18` flag modifies the ABI so Rust crates compiled with different values of this flag cannot be used together safely
= note: unset `-Zfixed-x18` in this crate is incompatible with `-Zfixed-x18=` in dependency `core`
= help: set `-Zfixed-x18=` in this crate or unset `-Zfixed-x18` in `core`
= help: if you are sure this will not cause problems, you may use `-Cunsafe-allow-abi-mismatch=fixed-x18` to silence this error
The reason is that `rustdoc` was not passing the target modifiers when
configuring the session options, and thus it would report a mismatch
that did not exist as soon as a target modifier is used in a dependency.
We did not notice it in the kernel until now because `-Zfixed-x18` has
been a target modifier only since 1.88.0 (and it is the only one we use
so far).
The issue has been reported upstream [1] and a fix has been submitted
[2], including a test similar to the kernel case.
[ This is now fixed upstream (thanks Guillaume for the quick review),
so it will be fixed in Rust 1.90.0 (expected 2025-09-18).
- Miguel ]
Meanwhile, conditionally pass `-Cunsafe-allow-abi-mismatch=fixed-x18`
to workaround the issue on our side.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/rust-for-linux/36cdc798-524f-4910-8b77-d7b9fac08d77@oss.qualcomm.com/
Link: https://github.com/rust-lang/rust/issues/144521 [1]
Link: https://github.com/rust-lang/rust/pull/144523 [2]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250727092317.2930617-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Futex hash allocations are done in mm_init() and the cleanup happens in
__mmput(). That works most of the time, but there are mm instances which
are instantiated via mm_alloc() and freed via mmdrop(), which causes the
futex hash to be leaked.
Move the cleanup to __mmdrop().
Fixes: 56180dd20c19 ("futex: Use RCU-based per-CPU reference counting instead of rcuref_t")
Reported-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/all/87ldo5ihu0.ffs@tglx
Closes: https://lore.kernel.org/all/0c8cc83bb73abf080faf584f319008b67d0931db.camel@linaro.org
Currently, when a Secure TSC enabled SNP guest attempts to write to the
intercepted GUEST_TSC_FREQ MSR (a read-only MSR), the guest kernel response
incorrectly implies a VMM configuration error, when in fact it is the usual
VMM configuration to intercept writes to read-only MSRs, unless explicitly
documented.
Modify the intercepted TSC MSR #VC handling:
* Write to GUEST_TSC_FREQ will generate a #GP instead of terminating the
guest
* Write to MSR_IA32_TSC will generate a #GP instead of silently ignoring it
However, continue to terminate the guest when reading from intercepted
GUEST_TSC_FREQ MSR with Secure TSC enabled, as intercepted reads indicate an
improper VMM configuration for Secure TSC enabled SNP guests.
[ bp: simplify comment. ]
Fixes: 38cc6495cdec ("x86/sev: Prevent GUEST_TSC_FREQ MSR interception for Secure TSC enabled guests")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/20250722074853.22253-1-nikunj@amd.com
Pull driver core fixes from Danilo Krummrich:
- Fix swapped handling of lru_gen and lru_gen_full debugfs files in
vmscan
- Fix debugfs mount options (uid, gid, mode) being silently ignored
- Fix leak of devres action in the unwind path of Devres::new()
- Documentation:
- Expand and fix documentation of (outdated) Device, DeviceContext
and generic driver infrastructure
- Fix C header link of faux device abstractions
- Clarify expected interaction with the security team
- Smooth text flow in the security bug reporting process
documentation
* tag 'driver-core-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
Documentation: smooth the text flow in the security bug reporting process
Documentation: clarify the expected collaboration with security bugs reporters
debugfs: fix mount options not being applied
rust: devres: fix leaking call to devm_add_action()
rust: faux: fix C header link
driver: rust: expand documentation for driver infrastructure
device: rust: expand documentation for Device
device: rust: expand documentation for DeviceContext
mm/vmscan: fix inverted polarity in lru_gen_seq_show()
Currently the reader of set_ftrace_filter and set_ftrace_notrace just adds
the pointer to the global tracer hash to its iterator. Unlike the writer
that allocates a copy of the hash, the reader keeps the pointer to the
filter hashes. This is problematic because this pointer is static across
function calls that release the locks that can update the global tracer
hashes. This can cause UAF and similar bugs.
Allocate and copy the hash for reading the filter files like it is done
for the writers. This not only fixes UAF bugs, but also makes the code a
bit simpler as it doesn't have to differentiate when to free the
iterator's hash between writers and readers.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20250822183606.12962cc3@batman.local.home
Fixes: c20489dad156 ("ftrace: Assign iter->hash to filter or notrace hashes on seq read")
Closes: https://lore.kernel.org/all/20250813023044.2121943-1-wutengda@huaweicloud.com/
Closes: https://lore.kernel.org/all/20250822192437.GA458494@ax162/
Reported-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953ed1 ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_rw_emulate_bits()` function is used as a default handler for
`INSN_READ` instructions for subdevices that have a handler for
`INSN_BITS` but not for `INSN_READ`. Similarly, it is used as a default
handler for `INSN_WRITE` instructions for subdevices that have a handler
for `INSN_BITS` but not for `INSN_WRITE`. It works by emulating the
`INSN_READ` or `INSN_WRITE` instruction handling with a constructed
`INSN_BITS` instruction. However, `INSN_READ` and `INSN_WRITE`
instructions are supposed to be able read or write multiple samples,
indicated by the `insn->n` value, but `insn_rw_emulate_bits()` currently
only handles a single sample. For `INSN_READ`, the comedi core will
copy `insn->n` samples back to user-space. (That triggered KASAN
kernel-infoleak errors when `insn->n` was greater than 1, but that is
being fixed more generally elsewhere in the comedi core.)
Make `insn_rw_emulate_bits()` either handle `insn->n` samples, or return
an error, to conform to the general expectation for `INSN_READ` and
`INSN_WRITE` handlers.
Fixes: ed9eccbe8970 ("Staging: add comedi core")
Cc: stable <stable@kernel.org> # 5.13+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20250725141034.87297-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given that the buffer is copied to a kfifo that ultimately user space
can read, ensure we zero it.
Fixes: 403e5586b52e ("iio: light: as73211: New driver")
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250802164436.515988-2-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Hogan reported a vector setup race, which overwrites the interrupt
descriptor in the per CPU vector array resulting in a disfunctional device.
CPU0 CPU1
interrupt is raised in APIC IRR
but not handled
free_irq()
per_cpu(vector_irq, CPU1)[vector] = VECTOR_SHUTDOWN;
request_irq() common_interrupt()
d = this_cpu_read(vector_irq[vector]);
per_cpu(vector_irq, CPU1)[vector] = desc;
if (d == VECTOR_SHUTDOWN)
this_cpu_write(vector_irq[vector], VECTOR_UNUSED);
free_irq() cannot observe the pending vector in the CPU1 APIC as there is
no way to query the remote CPUs APIC IRR.
This requires that request_irq() uses the same vector/CPU as the one which
was freed, but this also can be triggered by a spurious interrupt.
Interestingly enough this problem managed to be hidden for more than a
decade.
Prevent this by reevaluating vector_irq under the vector lock, which is
held by the interrupt activation code when vector_irq is updated.
To avoid ifdeffery or IS_ENABLED() nonsense, move the
[un]lock_vector_lock() declarations out under the
CONFIG_IRQ_DOMAIN_HIERARCHY guard as it's only provided when
CONFIG_X86_LOCAL_APIC=y.
The current CONFIG_IRQ_DOMAIN_HIERARCHY guard is selected by
CONFIG_X86_LOCAL_APIC, but can also be selected by other parts of the
Kconfig system, which makes 32-bit UP builds with CONFIG_X86_LOCAL_APIC=n
fail.
Can we just get rid of this !APIC nonsense once and forever?
Fixes: 9345005f4eed ("x86/irq: Fix do_IRQ() interrupt warning for cpu hotplug retriggered irqs")
Reported-by: Hogan Wang <hogan.wang@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hogan Wang <hogan.wang@huawei.com>
Link: https://lore.kernel.org/all/draft-87ikjhrhhh.ffs@tglx