tjh.dev
commits
Pull dmaengine fixes from Vinod Koul:
- tegra210 div_u64 divison and max page fixes
- revert Qualcomm unavailable register workaround which is causing
regression, fixes have been proposed but still gaps are present so
revert this for now
* tag 'dmaengine-fix-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: Revert "dmaengine: qcom: bam_dma: Avoid writing unavailable register"
dmaengine: tegra210-adma: check for adma max page
dmaengine: tegra210-adma: Use div_u64 for 64 bit division
Pull phy fixes from Vinod Koul:
- rockchip phy kconfig dependency fix with USB_COMMON and regression
fix for old DT
- stm32 phy overflow assertion fix
- exonysfs phy refclk masks fix and power gate on exit fix
- freescale fix for clock dividor valid range
- TI regmap syscon register fix
- tegra reset registers on init fix
* tag 'phy-fixes-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: tegra: xusb: reset VBUS & ID OVERRIDE
phy: ti: gmii-sel: Do not use syscon helper to build regmap
phy: exynos5-usbdrd: gs101: ensure power is gated to SS phy in phy_exit()
phy: freescale: fsl-samsung-hdmi: Limit PLL lock detection clock divider to valid range
phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk
phy: stm32: Fix constant-value overflow assertion
phy: rockchip: naneng-combphy: compatible reset with old DT
phy: rockchip: fix Kconfig dependency more
This commit causes a hard crash on sdm845 and likely other platforms.
Revert it until a proper fix is found.
This reverts commit 57a7138d0627: ("dmaengine: qcom: bam_dma: Avoid writing
unavailable register")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Fixes: 57a7138d0627 ("dmaengine: qcom: bam_dma: Avoid writing unavailable register")
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on sdm845-DB845c
Tested-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20250208223112.142567-1-caleb.connolly@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull gpio fix from Bartosz Golaszewski:
- fix a buggy get_direction() retval check
* tag 'gpio-fixes-for-v6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Fix Oops in gpiod_direction_input_nonotify()
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Fixes: bbf711682cd5 ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Change-Id: Ic63058d4d49b4a1f8f9ab313196e20ad131cc591
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20250122105943.8057-1-henryl@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Have additional check for max channel page during the probe
to cover if any offset overshoot happens due to wrong DT
configuration.
Fixes: 68811c928f88 ("dmaengine: tegra210-adma: Support channel page")
Cc: stable@vger.kernel.org
Signed-off-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250210135413.2504272-3-mkumard@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull MIPS fix from Thomas Bogendoerfer:
"Fix fallout of /scripts/sorttable cleanup"
* tag 'mips-fixes_6.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Ignore relocs against __ex_table for relocatable kernel
The gpiod_direction_input_nonotify() function is supposed to return zero
if the direction for the pin is input. But instead it accidentally
returns GPIO_LINE_DIRECTION_IN (1) which will be cast into an ERR_PTR()
in gpiochip_request_own_desc(). The callers dereference it and it leads
to a crash.
I changed gpiod_direction_output_raw_commit() just for consistency but
returning GPIO_LINE_DIRECTION_OUT (0) is fine.
Cc: stable@vger.kernel.org
Fixes: 9d846b1aebbe ("gpiolib: check the return value of gpio_chip::get_direction()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/254f3925-3015-4c9d-aac5-bb9b4b2cd2c5@stanley.mountain
[Bartosz: moved the variable declarations to the top of the functions]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.
This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250123182234.597665-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ADMA base and page address are represented using a 64-bit variable.
To accurately derive the exact ADMA page number provided from the DT
properties, use the div_u64() to divide the address difference between
adma page and base address by the page offset.
This change fixes the below error
"ERROR: modpost: "__udivdi3" [drivers/dma/tegra210-adma.ko] undefined!
ld: drivers/dma/tegra210-adma.o: in function `tegra_adma_probe':
tegra210-adma.c:(.text+0x12cf): undefined reference to `__udivdi3'"
Fixes: 68811c928f88 ("dmaengine: tegra210-adma: Support channel page")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412250204.GCQhdKe3-lkp@intel.com/
Signed-off-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250210135413.2504272-2-mkumard@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull smb client fix from Steve French:
"Fix SMB1 netfs client regression"
* tag 'v6.14-rc4-smb3-client-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix the smb1 readv callback to correctly call netfs
Since commit 6f2c2f93a190 ("scripts/sorttable: Remove unneeded
Elf_Rel"), sorttable no longer clears relocs against __ex_table,
claiming "it was never used." But in fact MIPS relocatable kernel had
been implicitly depending on this behavior, so after this commit the
MIPS relocatable kernel has started to spit oops like:
CPU 1 Unable to handle kernel paging request at virtual address 000000fffbbdbff8, epc == ffffffff818f9a6c, ra == ffffffff813ad7d0
... ...
Call Trace:
[<ffffffff818f9a6c>] __raw_copy_from_user+0x48/0x2fc
[<ffffffff813ad7d0>] cp_statx+0x1a0/0x1e0
[<ffffffff813ae528>] do_statx_fd+0xa8/0x118
[<ffffffff813ae670>] sys_statx+0xd8/0xf8
[<ffffffff81156cc8>] syscall_common+0x34/0x58
So ignore those relocs on our own to fix the issue.
Fixes: 6f2c2f93a190 ("scripts/sorttable: Remove unneeded Elf_Rel")
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We currently don't gate the power to the SS phy in phy_exit().
Shuffle the code slightly to ensure the power is gated to the SS phy as
well.
Fixes: 32267c29bc7d ("phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)")
CC: stable@vger.kernel.org # 6.11+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241205-gs101-usb-phy-fix-v4-1-0278809fb810@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull arm64 fixes from Will Deacon:
"Ryan's been hard at work finding and fixing mm bugs in the arm64 code,
so here's a small crop of fixes for -rc5.
The main changes are to fix our zapping of non-present PTEs for
hugetlb entries created using the contiguous bit in the page-table
rather than a block entry at the level above. Prior to these fixes, we
were pulling the contiguous bit back out of the PTE in order to
determine the size of the hugetlb page but this is clearly bogus if
the thing isn't present and consequently both the clearing of the
PTE(s) and the TLB invalidation were unreliable.
Although the problem was found by code inspection, we really don't
want this sitting around waiting to trigger and the changes are CC'd
to stable accordingly.
Note that the diffstat looks a lot worse than it really is;
huge_ptep_get_and_clear() now takes a size argument from the core code
and so all the arch implementations of that have been updated in a
pretty mechanical fashion.
- Fix a sporadic boot failure due to incorrect randomization of the
linear map on systems that support it
- Fix the zapping (both clearing the entries *and* invalidating the
TLB) of hugetlb PTEs constructed using the contiguous bit"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hugetlb: Fix flush_hugetlb_tlb_range() invalidation level
arm64: hugetlb: Fix huge_ptep_get_and_clear() for non-present ptes
mm: hugetlb: Add huge page size param to huge_ptep_get_and_clear()
arm64/mm: Fix Boot panic on Ampere Altra
Fix cifs_readv_callback() to call netfs_read_subreq_terminated() rather
than queuing the subrequest work item (which is unset). Also call the
I/O progress tracepoint.
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Fixes: e2d46f2ec332 ("netfs: Change the read result collector to only use one work item")
Reported-by: Jean-Christophe Guillain <jean-christophe@guillain.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219793
Tested-by: Jean-Christophe Guillain <jean-christophe@guillain.net>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Pull i2c fix from Wolfram Sang:
"Revert one cleanup which turned out to eat too much stack space"
* tag 'i2c-for-6.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Allocate temporary client dynamically
FIELD_PREP() checks that a value fits into the available bitfield,
but the index div equals to 4,is out of range.
which gcc complains about:
In function ‘fsl_samsung_hdmi_phy_configure_pll_lock_det’,
inlined from ‘fsl_samsung_hdmi_phy_configure’ at
drivers/phy/freescale/phy-fsl-samsung-hdmi.c :470:2:
././include/linux/compiler_types.h:542:38: error: call to ‘__compiletime_assert_538’
declared with attribute error: FIELD_PREP: value too large for the field
542 | _compiletime_assert(condition, msg, __compiletime_assert_,
__COUNTER__)
| ^
././include/linux/compiler_types.h:523:4: note: in definition of
macro ‘__compiletime_assert’ 523 | prefix ## suffix();
| ^~~~~~
././include/linux/compiler_types.h:542:2: note: in expansion of macro
‘_compiletime_assert’
542 | _compiletime_assert(condition, msg, __compiletime_assert_,
__COUNTER__)
REG12_CK_DIV_MASK only two bit, limit div to range 0~3,
so build error will fix.
Fixes: d567679f2b6a ("phy: freescale: fsl-samsung-hdmi: Clean up fld_tg_code calculation")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Changlog:
Reviewed-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/tencent_6F503D43467AA99DD8CC59B8F645F0725B0A@qq.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Pull i2c fixes from Wolfram Sang:
"All driver fixes this time:
- fix interrupt initialization sequence (npcm)
- fix frequency setting (ls2x)
- re-enable interrupts properly at irq handler's exit (amd-asf)"
* tag 'i2c-for-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: amd-asf: Fix EOI register write to enable successive interrupts
i2c: ls2x: Fix frequency division register access
i2c: npcm: disable interrupt enable bit before devm_request_irq
commit c910f2b65518 ("arm64/mm: Update tlb invalidation routines for
FEAT_LPA2") changed the "invalidation level unknown" hint from 0 to
TLBI_TTL_UNKNOWN (INT_MAX). But the fallback "unknown level" path in
flush_hugetlb_tlb_range() was not updated. So as it stands, when trying
to invalidate CONT_PMD_SIZE or CONT_PTE_SIZE hugetlb mappings, we will
spuriously try to invalidate at level 0 on LPA2-enabled systems.
Fix this so that the fallback passes TLBI_TTL_UNKNOWN, and while we are
at it, explicitly use the correct stride and level for CONT_PMD_SIZE and
CONT_PTE_SIZE, which should provide a minor optimization.
Cc: stable@vger.kernel.org
Fixes: c910f2b65518 ("arm64/mm: Update tlb invalidation routines for FEAT_LPA2")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-4-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull Kbuild fixes from Masahiro Yamada:
- Fix annoying logs when building tools in parallel
- Fix the Debian linux-headers package build again
- Fix the target triple detection for userspace programs on Clang
* tag 'kbuild-fixes-v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: Fix a few typos in a comment
kbuild: userprogs: fix bitsize and target detection on clang
kbuild: fix linux-headers package build when $(CC) cannot link userspace
tools: fix annoying "mkdir -p ..." logs when building tools in parallel
Pull EDAC fix from Borislav Petkov:
- Have qcom_edac use the correct interrupt enable register to configure
the RAS interrupt lines
* tag 'edac_urgent_for_v6.14_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/qcom: Correct interrupt enable register configuration
drivers/i2c/i2c-core-base.c: In function ‘i2c_detect.isra’:
drivers/i2c/i2c-core-base.c:2544:1: warning: the frame size of 1312 bytes is larger than 1024 bytes [-Wframe-larger-than=]
2544 | }
| ^
Fix this by allocating the temporary client structure dynamically, as it
is a rather large structure (1216 bytes, depending on kernel config).
This is basically a revert of the to-be-fixed commit with some
checkpatch improvements.
Fixes: 735668f8e5c9 ("i2c: core: Allocate temp client on the stack in i2c_detect")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[wsa: updated commit message, merged tags from similar patch]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
In exynos5_usbdrd_{pipe3,utmi}_set_refclk(), the masks
PHYCLKRST_MPLL_MULTIPLIER_MASK and PHYCLKRST_SSC_REFCLKSEL_MASK are not
inverted when applied to the register values. Fix it.
Cc: stable@vger.kernel.org
Fixes: 59025887fb08 ("phy: Add new Exynos5 USB 3.0 PHY driver")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20250209-exynos5-usbdrd-masks-v1-1-4f7f83f323d7@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ata fixes from Niklas Cassel:
- Fix a regression where the enablement of the PHYs would be skipped
for device trees without any port child nodes (me)
- Revert ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives, as it stops
systems from entering lower package states. LPM works on newer
firmware versions. We will need a more refined quirk that only
targets the older firmware versions (me)
* tag 'ata-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
Revert "ata: libata-core: Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives"
ata: ahci: Make ahci_ignore_port() handle empty mask_port_map
i2c-host-fixes for v6.14-rc5
- npcm fixes interrupt initialization sequence.
- ls2x fixes frequency setting.
- amd-asf re-enables interrupts properly at irq handler's exit.
arm64 supports multiple huge_pte sizes. Some of the sizes are covered by
a single pte entry at a particular level (PMD_SIZE, PUD_SIZE), and some
are covered by multiple ptes at a particular level (CONT_PTE_SIZE,
CONT_PMD_SIZE). So the function has to figure out the size from the
huge_pte pointer. This was previously done by walking the pgtable to
determine the level and by using the PTE_CONT bit to determine the
number of ptes at the level.
But the PTE_CONT bit is only valid when the pte is present. For
non-present pte values (e.g. markers, migration entries), the previous
implementation was therefore erroneously determining the size. There is
at least one known caller in core-mm, move_huge_pte(), which may call
huge_ptep_get_and_clear() for a non-present pte. So we must be robust to
this case. Additionally the "regular" ptep_get_and_clear() is robust to
being called for non-present ptes so it makes sense to follow the
behavior.
Fix this by using the new sz parameter which is now provided to the
function. Additionally when clearing each pte in a contig range, don't
gather the access and dirty bits if the pte is not present.
An alternative approach that would not require API changes would be to
store the PTE_CONT bit in a spare bit in the swap entry pte for the
non-present case. But it felt cleaner to follow other APIs' lead and
just pass in the size.
As an aside, PTE_CONT is bit 52, which corresponds to bit 40 in the swap
entry offset field (layout of non-present pte). Since hugetlb is never
swapped to disk, this field will only be populated for markers, which
always set this bit to 0 and hwpoison swap entries, which set the offset
field to a PFN; So it would only ever be 1 for a 52-bit PVA system where
memory in that high half was poisoned (I think!). So in practice, this
bit would almost always be zero for non-present ptes and we would only
clear the first entry if it was actually a contiguous block. That's
probably a less severe symptom than if it was always interpreted as 1
and cleared out potentially-present neighboring PTEs.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-3-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull driver core api addition from Greg KH:
"Here is a driver core new api for 6.14-rc3 that is being added to
allow platform devices from stop being abused.
It adds a new 'faux_device' structure and bus and api to allow almost
a straight or simpler conversion from platform devices that were not
really a platform device. It also comes with a binding for rust, with
an example driver in rust showing how it's used.
I'm adding this now so that the patches that convert the different
drivers and subsystems can all start flowing into linux-next now
through their different development trees, in time for 6.15-rc1.
We have a number that are already reviewed and tested, but adding
those conversions now doesn't seem right. For now, no one is using
this, and it passes all build tests from 0-day and linux-next, so all
should be good"
* tag 'driver-core-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
rust/kernel: Add faux device bindings
driver core: add a faux bus for use when a simple device/bus is needed
Namely: s/becasue/because/ and s/wiht/with/ plus an added article.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull smb client fix from Steve French:
- Fix potential null pointer dereference
* tag 'v6.14-rc3-smb3-client-fix-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: Add check for next_buffer in receive_encrypted_standard()
The previous implementation incorrectly configured the cmn_interrupt_2_enable
register for interrupt handling. Using cmn_interrupt_2_enable to configure
Tag, Data RAM ECC interrupts would lead to issues like double handling of the
interrupts (EL1 and EL3) as cmn_interrupt_2_enable is meant to be configured
for interrupts which needs to be handled by EL3.
EL1 LLCC EDAC driver needs to use cmn_interrupt_0_enable register to configure
Tag, Data RAM ECC interrupts instead of cmn_interrupt_2_enable.
Fixes: 27450653f1db ("drivers: edac: Add EDAC driver support for QCOM SoCs")
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20241119064608.12326-1-quic_kbajaj@quicinc.com
Rework the workaround as the lookup tables always fits into the bitfield,
and the default values are defined by the hardware and cannot be 0:
Guard against false positive with a WARN_ON check to make the compiler
happy: The offset range is pre-checked against the sorted imp_lookup_table
values and overflow should not happen and would be caught by a warning and
return in error.
Also guard against a true positive found during the max_vswing lookup, as a
max vswing value can be 802000 or 803000 microvolt depending on the current
impedance. Therefore set the default impedence index.
Fixes: 2de679ecd724 ("phy: stm32: work around constant-value overflow assertion")
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Link: https://lore.kernel.org/r/20250210103515.2598377-1-christian.bruel@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
If CONFIG_I2C=n:
WARNING: unmet direct dependencies detected for SND_SOC_AK4642
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && I2C [=n]
Selected by [y]:
- SH_7724_SOLUTION_ENGINE [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
WARNING: unmet direct dependencies detected for SND_SOC_DA7210
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && SND_SOC_I2C_AND_SPI [=n]
Selected by [y]:
- SH_ECOVEC [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
Fix this by replacing select by imply, instead of adding a dependency on
I2C.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501240836.OvXqmANX-lkp@intel.com/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Intel Clearwater Forest report PMT telemetry with GUID 0x14421519, which
can be used to obtain module c1e residency counter of type tcore clock.
Add early support for the counter by using heuristic that should work
for the Clearwater Forest platforms.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix TCR_EL2 configuration to not use the ASID in TTBR1_EL2 and not
mess-up T1SZ/PS by using the HCR_EL2.E2H==0 layout.
- Bring back the VMID allocation to the vcpu_load phase, ensuring
that we only setup VTTBR_EL2 once on VHE. This cures an ugly race
that would lead to running with an unallocated VMID.
RISC-V:
- Fix hart status check in SBI HSM extension
- Fix hart suspend_type usage in SBI HSM extension
- Fix error returned by SBI IPI and TIME extensions for unsupported
function IDs
- Fix suspend_type usage in SBI SUSP extension
- Remove unnecessary vcpu kick after injecting interrupt via IMSIC
guest file
x86:
- Fix an nVMX bug where KVM fails to detect that, after nested
VM-Exit, L1 has a pending IRQ (or NMI).
- To avoid freeing the PIC while vCPUs are still around, which would
cause a NULL pointer access with the previous patch, destroy vCPUs
before any VM-level destruction.
- Handle failures to create vhost_tasks"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: retry nx_huge_page_recovery_thread creation
vhost: return task creation error instead of NULL
KVM: nVMX: Process events on nested VM-Exit if injectable IRQ or NMI is pending
KVM: x86: Free vCPUs before freeing VM state
riscv: KVM: Remove unnecessary vcpu kick
KVM: arm64: Ensure a VMID is allocated before programming VTTBR_EL2
KVM: arm64: Fix tcr_el2 initialisation in hVHE mode
riscv: KVM: Fix SBI sleep_type use
riscv: KVM: Fix SBI TIME error generation
riscv: KVM: Fix SBI IPI error generation
riscv: KVM: Fix hart suspend_type use
riscv: KVM: Fix hart suspend status check
This reverts commit cc77e2ce187d26cc66af3577bf896d7410eb25ab.
It was reported that adding ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives
breaks entering lower package states for certain systems.
It turns out that Samsung SSD 870 QVO actually has working LPM when using
a recent SSD firmware version.
The author of commit cc77e2ce187d ("ata: libata-core: Add ATA_QUIRK_NOLPM
for Samsung SSD 870 QVO drives") reported himself that only older SSD
firmware versions have broken LPM:
https://lore.kernel.org/stable/93c10d38-718c-459d-84a5-4d87680b4da7@debian.org/
Unfortunately, he did not specify which older firmware version he was using
which had broken LPM.
Let's revert this quirk, which has FW version field specified as NULL
(which means that it applies for all Samsung SSD 870 QVO firmware versions)
for now. Once the author reports which older firmware version(s) that are
broken, we can create a more fine grained quirk, which populates the FW
version field accordingly.
Fixes: cc77e2ce187d ("ata: libata-core: Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives")
Reported-by: Dieter Mummenschanz <dmummenschanz@web.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219747
Link: https://lore.kernel.org/r/20250228122603.91814-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The commit b1f8921dfbaa
("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
introduced a method to enable successive interrupts but inadvertently
omitted the necessary write to the EOI register, resulting in a failure to
receive successive interrupts.
Fix this by adding the required write to the EOI register.
Fixes: b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
Cc: stable@vger.kernel.org # v6.13+
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Fixes: 9b25419ad397 ("i2c: amd-asf: Add routine to handle the ASF slave process")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250219135747.3251182-1-Shyam-sundar.S-k@amd.com
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390
Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for some reported problems.
Nothing major, just:
- sc16is7xx irq check fix
- 8250 fifo underflow fix
- serial_port and 8250 iotype fixes
Most of these have been in linux-next already, and all have passed
0-day testing"
* tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: Fix fifo underflow on flush
serial: 8250_pnp: Remove unneeded ->iotype assignment
serial: 8250_platform: Remove unneeded ->iotype assignment
serial: 8250_of: Remove unneeded ->iotype assignment
serial: port: Make ->iotype validation global in __uart_read_properties()
serial: port: Always update ->iotype in __uart_read_properties()
serial: port: Assign ->iotype correctly when ->iobase is set
serial: sc16is7xx: Fix IRQ number check behavior
This introduces a module for working with faux devices in rust, along with
adding sample code to show how the API is used. Unlike other types of
devices, we don't provide any hooks for device probe/removal - since these
are optional for the faux API and are unnecessary in rust.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Maíra Canal <mairacanal@riseup.net>
Cc: Danilo Krummrich <dakr@kernel.org>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/2025021026-exert-accent-b4c6@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scripts/Makefile.clang was changed in the linked commit to move --target from
KBUILD_CFLAGS to KBUILD_CPPFLAGS, as that generally has a broader scope.
However that variable is not inspected by the userprogs logic,
breaking cross compilation on clang.
Use both variables to detect bitsize and target arguments for userprogs.
Fixes: feb843a469fb ("kbuild: add $(CLANG_FLAGS) to KBUILD_CPPFLAGS")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull x86 fixes from Ingo Molnar:
- Fix AVX-VNNI CPU feature dependency bug triggered via the 'noxsave'
boot option
- Fix typos in the SVA documentation
- Add Tony Luck as RDT co-maintainer and remove Fenghua Yu
* tag 'x86-urgent-2025-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
docs: arch/x86/sva: Fix two grammar errors under Background and FAQ
x86/cpufeatures: Make AVX-VNNI depend on AVX
MAINTAINERS: Change maintainer for RDT
Add check for the return value of cifs_buf_get() and cifs_small_buf_get()
in receive_encrypted_standard() to prevent null pointer dereference.
Fixes: eec04ea11969 ("smb: client: fix OOB in receive_encrypted_standard()")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The device tree of RK3568 did not specify reset-names before.
So add fallback to old behaviour to be compatible with old DT.
Fixes: fbcbffbac994 ("phy: rockchip: naneng-combphy: fix phy reset")
Cc: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250106100001.1344418-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull MIPS fix from Thomas Bogendoerfer:
"Revert commit breaking sysv ipc for o32 ABI"
* tag 'mips_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "mips: fix shmctl/semctl/msgctl syscall for o32"
Quite a few places want to build a struct qstr by given string;
it would be convenient to have a primitive doing that, rather
than open-coding it via QSTR_INIT().
The closest approximation was in bcachefs, but that expands to
initializer list - {.len = strlen(string), .name = string}.
It would be more useful to have it as compound literal -
(struct qstr){.len = strlen(string), .name = string}.
Unlike initializer list it's a valid expression. What's more,
it's a valid lvalue - it's an equivalent of anonymous local
variable with such initializer, so the things like
path->dentry = d_alloc_pseudo(mnt->mnt_sb, &QSTR(name));
are valid. It can also be used as initializer, with identical
effect -
struct qstr x = (struct qstr){.name = s, .len = strlen(s)};
is equivalent to
struct qstr anon_variable = {.name = s, .len = strlen(s)};
struct qstr x = anon_variable;
// anon_variable is never used after that point
and any even remotely sane compiler will manage to collapse that
into
struct qstr x = {.name = s, .len = strlen(s)};
What compound literals can't be used for is initialization of
global variables, but those are covered by QSTR_INIT().
This commit lifts definition(s) of QSTR() into linux/dcache.h,
converts it to compound literal (all bcachefs users are fine
with that) and converts assorted open-coded instances to using
that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 654102df2ac2 ("kbuild: add generic support for built-in
boot DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB when built-in DTB support is enabled.
To keep consistency across architectures, this commit also renames
CONFIG_USE_BUILTIN_DTB to CONFIG_BUILTIN_DTB, and
CONFIG_BUILTIN_DTB_SOURCE to CONFIG_BUILTIN_DTB_NAME.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
when turbostat interval mode can't migrate to a CPU, it complains,
prints no data, re-initializes with the new CPU configuration
and starts a new interval.
But this strategy in the face of a CPU hotplug offline during an interval
doesn't help in one-shot mode. When the missing CPU is discovered
at the end of the interval, the forked program has already returned
and there is nothing left for a new interval to measure.
So instead of aborting get_coutners() and delta_cpu() if a missing CPU
is detected, complain, but carry on and output what statistics are
actually present.
Use the same strategy for delta_cpu when aperf:mperf are observed
to have been reset -- complain, but carry on and print data for
the CPUs that are still present.
Interval mode error handling is unchanged.
One-shot mode can now do this:
$ sudo chcpu -e 1 ; sudo ./turbostat --quiet --show PkgWatt,Busy%,CPU chcpu -d 1
CPU 1 enabled
CPU 1 disabled
get_counters: Could not migrate to CPU 1
./turbostat: Counter reset detected
0.036920 sec
CPU Busy% PkgWatt
- 0.00 10.00
0 99.73 10.00
1 0.00
2 91.53
3 16.83
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull thermal control fixes from Rafael Wysocki:
"These fix the processing of DT thermal properties and the Power
Allocator thermal governor:
- Fix parsing cooling-maps in DT for trip points with more than one
cooling device (Rafael Wysocki)
- Fix granted_power computation in the Power Allocator thermal
governor and make it update total_weight on configuration changes
after the thermal zone has been registered (Yu-Che Cheng)"
* tag 'thermal-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: gov_power_allocator: Update total_weight on bind and cdev updates
thermal/of: Fix cdev lookup in thermal_of_should_bind()
thermal: gov_power_allocator: Fix incorrect calculation in divvy_up_power()
A VMM may send a non-fatal signal to its threads, including vCPU tasks,
at any time, and thus may signal vCPU tasks during KVM_RUN. If a vCPU
task receives the signal while its trying to spawn the huge page recovery
vhost task, then KVM_RUN will fail due to copy_process() returning
-ERESTARTNOINTR.
Rework call_once() to mark the call complete if and only if the called
function succeeds, and plumb the function's true error code back to the
call_once() invoker. This provides userspace with the correct, non-fatal
error code so that the VMM doesn't terminate the VM on -ENOMEM, and allows
subsequent KVM_RUN a succeed by virtue of retrying creation of the NX huge
page task.
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
[implemented the kvm user side]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Message-ID: <20250227230631.303431-3-kbusch@meta.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port
numbers") added a skip to ahci_platform_enable_phys() for ports that are
not in mask_port_map.
The code in ahci_platform_get_resources(), will currently set mask_port_map
for each child "port" node it finds in the device tree.
However, device trees that do not have any child "port" nodes will not have
mask_port_map set, and for non-device tree platforms mask_port_map will
only exist as a quirk for specific PCI device + vendor IDs, or as a kernel
module parameter, but will not be set by default.
Therefore, the common thing is that mask_port_map is only set if you do not
want to use all ports (as defined by Offset 0Ch: PI – Ports Implemented
register), but instead only want to use the ports in mask_port_map. If
mask_port_map is not set, all ports are available.
Thus, ahci_ignore_port() must be able to handle an empty mask_port_map.
Fixes: 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port numbers")
Fixes: 2c202e6c4f4d ("ata: libahci_platform: Do not set mask_port_map when not needed")
Fixes: c9b5be909e65 ("ahci: Introduce ahci_ignore_port() helper")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-ide/10b31dd0-d0bb-4f76-9305-2195c3e17670@samsung.com/
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250225141612.942170-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
Pull dmaengine fixes from Vinod Koul:
- tegra210 div_u64 divison and max page fixes
- revert Qualcomm unavailable register workaround which is causing
regression, fixes have been proposed but still gaps are present so
revert this for now
* tag 'dmaengine-fix-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: Revert "dmaengine: qcom: bam_dma: Avoid writing unavailable register"
dmaengine: tegra210-adma: check for adma max page
dmaengine: tegra210-adma: Use div_u64 for 64 bit division
Pull phy fixes from Vinod Koul:
- rockchip phy kconfig dependency fix with USB_COMMON and regression
fix for old DT
- stm32 phy overflow assertion fix
- exonysfs phy refclk masks fix and power gate on exit fix
- freescale fix for clock dividor valid range
- TI regmap syscon register fix
- tegra reset registers on init fix
* tag 'phy-fixes-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: tegra: xusb: reset VBUS & ID OVERRIDE
phy: ti: gmii-sel: Do not use syscon helper to build regmap
phy: exynos5-usbdrd: gs101: ensure power is gated to SS phy in phy_exit()
phy: freescale: fsl-samsung-hdmi: Limit PLL lock detection clock divider to valid range
phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk
phy: stm32: Fix constant-value overflow assertion
phy: rockchip: naneng-combphy: compatible reset with old DT
phy: rockchip: fix Kconfig dependency more
This commit causes a hard crash on sdm845 and likely other platforms.
Revert it until a proper fix is found.
This reverts commit 57a7138d0627: ("dmaengine: qcom: bam_dma: Avoid writing
unavailable register")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Fixes: 57a7138d0627 ("dmaengine: qcom: bam_dma: Avoid writing unavailable register")
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on sdm845-DB845c
Tested-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20250208223112.142567-1-caleb.connolly@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Fixes: bbf711682cd5 ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Change-Id: Ic63058d4d49b4a1f8f9ab313196e20ad131cc591
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20250122105943.8057-1-henryl@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Have additional check for max channel page during the probe
to cover if any offset overshoot happens due to wrong DT
configuration.
Fixes: 68811c928f88 ("dmaengine: tegra210-adma: Support channel page")
Cc: stable@vger.kernel.org
Signed-off-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250210135413.2504272-3-mkumard@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The gpiod_direction_input_nonotify() function is supposed to return zero
if the direction for the pin is input. But instead it accidentally
returns GPIO_LINE_DIRECTION_IN (1) which will be cast into an ERR_PTR()
in gpiochip_request_own_desc(). The callers dereference it and it leads
to a crash.
I changed gpiod_direction_output_raw_commit() just for consistency but
returning GPIO_LINE_DIRECTION_OUT (0) is fine.
Cc: stable@vger.kernel.org
Fixes: 9d846b1aebbe ("gpiolib: check the return value of gpio_chip::get_direction()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/254f3925-3015-4c9d-aac5-bb9b4b2cd2c5@stanley.mountain
[Bartosz: moved the variable declarations to the top of the functions]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.
This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250123182234.597665-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ADMA base and page address are represented using a 64-bit variable.
To accurately derive the exact ADMA page number provided from the DT
properties, use the div_u64() to divide the address difference between
adma page and base address by the page offset.
This change fixes the below error
"ERROR: modpost: "__udivdi3" [drivers/dma/tegra210-adma.ko] undefined!
ld: drivers/dma/tegra210-adma.o: in function `tegra_adma_probe':
tegra210-adma.c:(.text+0x12cf): undefined reference to `__udivdi3'"
Fixes: 68811c928f88 ("dmaengine: tegra210-adma: Support channel page")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412250204.GCQhdKe3-lkp@intel.com/
Signed-off-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250210135413.2504272-2-mkumard@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 6f2c2f93a190 ("scripts/sorttable: Remove unneeded
Elf_Rel"), sorttable no longer clears relocs against __ex_table,
claiming "it was never used." But in fact MIPS relocatable kernel had
been implicitly depending on this behavior, so after this commit the
MIPS relocatable kernel has started to spit oops like:
CPU 1 Unable to handle kernel paging request at virtual address 000000fffbbdbff8, epc == ffffffff818f9a6c, ra == ffffffff813ad7d0
... ...
Call Trace:
[<ffffffff818f9a6c>] __raw_copy_from_user+0x48/0x2fc
[<ffffffff813ad7d0>] cp_statx+0x1a0/0x1e0
[<ffffffff813ae528>] do_statx_fd+0xa8/0x118
[<ffffffff813ae670>] sys_statx+0xd8/0xf8
[<ffffffff81156cc8>] syscall_common+0x34/0x58
So ignore those relocs on our own to fix the issue.
Fixes: 6f2c2f93a190 ("scripts/sorttable: Remove unneeded Elf_Rel")
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We currently don't gate the power to the SS phy in phy_exit().
Shuffle the code slightly to ensure the power is gated to the SS phy as
well.
Fixes: 32267c29bc7d ("phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)")
CC: stable@vger.kernel.org # 6.11+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241205-gs101-usb-phy-fix-v4-1-0278809fb810@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull arm64 fixes from Will Deacon:
"Ryan's been hard at work finding and fixing mm bugs in the arm64 code,
so here's a small crop of fixes for -rc5.
The main changes are to fix our zapping of non-present PTEs for
hugetlb entries created using the contiguous bit in the page-table
rather than a block entry at the level above. Prior to these fixes, we
were pulling the contiguous bit back out of the PTE in order to
determine the size of the hugetlb page but this is clearly bogus if
the thing isn't present and consequently both the clearing of the
PTE(s) and the TLB invalidation were unreliable.
Although the problem was found by code inspection, we really don't
want this sitting around waiting to trigger and the changes are CC'd
to stable accordingly.
Note that the diffstat looks a lot worse than it really is;
huge_ptep_get_and_clear() now takes a size argument from the core code
and so all the arch implementations of that have been updated in a
pretty mechanical fashion.
- Fix a sporadic boot failure due to incorrect randomization of the
linear map on systems that support it
- Fix the zapping (both clearing the entries *and* invalidating the
TLB) of hugetlb PTEs constructed using the contiguous bit"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hugetlb: Fix flush_hugetlb_tlb_range() invalidation level
arm64: hugetlb: Fix huge_ptep_get_and_clear() for non-present ptes
mm: hugetlb: Add huge page size param to huge_ptep_get_and_clear()
arm64/mm: Fix Boot panic on Ampere Altra
Fix cifs_readv_callback() to call netfs_read_subreq_terminated() rather
than queuing the subrequest work item (which is unset). Also call the
I/O progress tracepoint.
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Fixes: e2d46f2ec332 ("netfs: Change the read result collector to only use one work item")
Reported-by: Jean-Christophe Guillain <jean-christophe@guillain.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219793
Tested-by: Jean-Christophe Guillain <jean-christophe@guillain.net>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
FIELD_PREP() checks that a value fits into the available bitfield,
but the index div equals to 4,is out of range.
which gcc complains about:
In function ‘fsl_samsung_hdmi_phy_configure_pll_lock_det’,
inlined from ‘fsl_samsung_hdmi_phy_configure’ at
drivers/phy/freescale/phy-fsl-samsung-hdmi.c :470:2:
././include/linux/compiler_types.h:542:38: error: call to ‘__compiletime_assert_538’
declared with attribute error: FIELD_PREP: value too large for the field
542 | _compiletime_assert(condition, msg, __compiletime_assert_,
__COUNTER__)
| ^
././include/linux/compiler_types.h:523:4: note: in definition of
macro ‘__compiletime_assert’ 523 | prefix ## suffix();
| ^~~~~~
././include/linux/compiler_types.h:542:2: note: in expansion of macro
‘_compiletime_assert’
542 | _compiletime_assert(condition, msg, __compiletime_assert_,
__COUNTER__)
REG12_CK_DIV_MASK only two bit, limit div to range 0~3,
so build error will fix.
Fixes: d567679f2b6a ("phy: freescale: fsl-samsung-hdmi: Clean up fld_tg_code calculation")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Changlog:
Reviewed-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/tencent_6F503D43467AA99DD8CC59B8F645F0725B0A@qq.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Pull i2c fixes from Wolfram Sang:
"All driver fixes this time:
- fix interrupt initialization sequence (npcm)
- fix frequency setting (ls2x)
- re-enable interrupts properly at irq handler's exit (amd-asf)"
* tag 'i2c-for-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: amd-asf: Fix EOI register write to enable successive interrupts
i2c: ls2x: Fix frequency division register access
i2c: npcm: disable interrupt enable bit before devm_request_irq
commit c910f2b65518 ("arm64/mm: Update tlb invalidation routines for
FEAT_LPA2") changed the "invalidation level unknown" hint from 0 to
TLBI_TTL_UNKNOWN (INT_MAX). But the fallback "unknown level" path in
flush_hugetlb_tlb_range() was not updated. So as it stands, when trying
to invalidate CONT_PMD_SIZE or CONT_PTE_SIZE hugetlb mappings, we will
spuriously try to invalidate at level 0 on LPA2-enabled systems.
Fix this so that the fallback passes TLBI_TTL_UNKNOWN, and while we are
at it, explicitly use the correct stride and level for CONT_PMD_SIZE and
CONT_PTE_SIZE, which should provide a minor optimization.
Cc: stable@vger.kernel.org
Fixes: c910f2b65518 ("arm64/mm: Update tlb invalidation routines for FEAT_LPA2")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-4-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull Kbuild fixes from Masahiro Yamada:
- Fix annoying logs when building tools in parallel
- Fix the Debian linux-headers package build again
- Fix the target triple detection for userspace programs on Clang
* tag 'kbuild-fixes-v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: Fix a few typos in a comment
kbuild: userprogs: fix bitsize and target detection on clang
kbuild: fix linux-headers package build when $(CC) cannot link userspace
tools: fix annoying "mkdir -p ..." logs when building tools in parallel
drivers/i2c/i2c-core-base.c: In function ‘i2c_detect.isra’:
drivers/i2c/i2c-core-base.c:2544:1: warning: the frame size of 1312 bytes is larger than 1024 bytes [-Wframe-larger-than=]
2544 | }
| ^
Fix this by allocating the temporary client structure dynamically, as it
is a rather large structure (1216 bytes, depending on kernel config).
This is basically a revert of the to-be-fixed commit with some
checkpatch improvements.
Fixes: 735668f8e5c9 ("i2c: core: Allocate temp client on the stack in i2c_detect")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[wsa: updated commit message, merged tags from similar patch]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
In exynos5_usbdrd_{pipe3,utmi}_set_refclk(), the masks
PHYCLKRST_MPLL_MULTIPLIER_MASK and PHYCLKRST_SSC_REFCLKSEL_MASK are not
inverted when applied to the register values. Fix it.
Cc: stable@vger.kernel.org
Fixes: 59025887fb08 ("phy: Add new Exynos5 USB 3.0 PHY driver")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20250209-exynos5-usbdrd-masks-v1-1-4f7f83f323d7@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ata fixes from Niklas Cassel:
- Fix a regression where the enablement of the PHYs would be skipped
for device trees without any port child nodes (me)
- Revert ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives, as it stops
systems from entering lower package states. LPM works on newer
firmware versions. We will need a more refined quirk that only
targets the older firmware versions (me)
* tag 'ata-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
Revert "ata: libata-core: Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives"
ata: ahci: Make ahci_ignore_port() handle empty mask_port_map
arm64 supports multiple huge_pte sizes. Some of the sizes are covered by
a single pte entry at a particular level (PMD_SIZE, PUD_SIZE), and some
are covered by multiple ptes at a particular level (CONT_PTE_SIZE,
CONT_PMD_SIZE). So the function has to figure out the size from the
huge_pte pointer. This was previously done by walking the pgtable to
determine the level and by using the PTE_CONT bit to determine the
number of ptes at the level.
But the PTE_CONT bit is only valid when the pte is present. For
non-present pte values (e.g. markers, migration entries), the previous
implementation was therefore erroneously determining the size. There is
at least one known caller in core-mm, move_huge_pte(), which may call
huge_ptep_get_and_clear() for a non-present pte. So we must be robust to
this case. Additionally the "regular" ptep_get_and_clear() is robust to
being called for non-present ptes so it makes sense to follow the
behavior.
Fix this by using the new sz parameter which is now provided to the
function. Additionally when clearing each pte in a contig range, don't
gather the access and dirty bits if the pte is not present.
An alternative approach that would not require API changes would be to
store the PTE_CONT bit in a spare bit in the swap entry pte for the
non-present case. But it felt cleaner to follow other APIs' lead and
just pass in the size.
As an aside, PTE_CONT is bit 52, which corresponds to bit 40 in the swap
entry offset field (layout of non-present pte). Since hugetlb is never
swapped to disk, this field will only be populated for markers, which
always set this bit to 0 and hwpoison swap entries, which set the offset
field to a PFN; So it would only ever be 1 for a 52-bit PVA system where
memory in that high half was poisoned (I think!). So in practice, this
bit would almost always be zero for non-present ptes and we would only
clear the first entry if it was actually a contiguous block. That's
probably a less severe symptom than if it was always interpreted as 1
and cleared out potentially-present neighboring PTEs.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-3-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull driver core api addition from Greg KH:
"Here is a driver core new api for 6.14-rc3 that is being added to
allow platform devices from stop being abused.
It adds a new 'faux_device' structure and bus and api to allow almost
a straight or simpler conversion from platform devices that were not
really a platform device. It also comes with a binding for rust, with
an example driver in rust showing how it's used.
I'm adding this now so that the patches that convert the different
drivers and subsystems can all start flowing into linux-next now
through their different development trees, in time for 6.15-rc1.
We have a number that are already reviewed and tested, but adding
those conversions now doesn't seem right. For now, no one is using
this, and it passes all build tests from 0-day and linux-next, so all
should be good"
* tag 'driver-core-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
rust/kernel: Add faux device bindings
driver core: add a faux bus for use when a simple device/bus is needed
The previous implementation incorrectly configured the cmn_interrupt_2_enable
register for interrupt handling. Using cmn_interrupt_2_enable to configure
Tag, Data RAM ECC interrupts would lead to issues like double handling of the
interrupts (EL1 and EL3) as cmn_interrupt_2_enable is meant to be configured
for interrupts which needs to be handled by EL3.
EL1 LLCC EDAC driver needs to use cmn_interrupt_0_enable register to configure
Tag, Data RAM ECC interrupts instead of cmn_interrupt_2_enable.
Fixes: 27450653f1db ("drivers: edac: Add EDAC driver support for QCOM SoCs")
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20241119064608.12326-1-quic_kbajaj@quicinc.com
Rework the workaround as the lookup tables always fits into the bitfield,
and the default values are defined by the hardware and cannot be 0:
Guard against false positive with a WARN_ON check to make the compiler
happy: The offset range is pre-checked against the sorted imp_lookup_table
values and overflow should not happen and would be caught by a warning and
return in error.
Also guard against a true positive found during the max_vswing lookup, as a
max vswing value can be 802000 or 803000 microvolt depending on the current
impedance. Therefore set the default impedence index.
Fixes: 2de679ecd724 ("phy: stm32: work around constant-value overflow assertion")
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Link: https://lore.kernel.org/r/20250210103515.2598377-1-christian.bruel@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
If CONFIG_I2C=n:
WARNING: unmet direct dependencies detected for SND_SOC_AK4642
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && I2C [=n]
Selected by [y]:
- SH_7724_SOLUTION_ENGINE [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
WARNING: unmet direct dependencies detected for SND_SOC_DA7210
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && SND_SOC_I2C_AND_SPI [=n]
Selected by [y]:
- SH_ECOVEC [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
Fix this by replacing select by imply, instead of adding a dependency on
I2C.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501240836.OvXqmANX-lkp@intel.com/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Intel Clearwater Forest report PMT telemetry with GUID 0x14421519, which
can be used to obtain module c1e residency counter of type tcore clock.
Add early support for the counter by using heuristic that should work
for the Clearwater Forest platforms.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix TCR_EL2 configuration to not use the ASID in TTBR1_EL2 and not
mess-up T1SZ/PS by using the HCR_EL2.E2H==0 layout.
- Bring back the VMID allocation to the vcpu_load phase, ensuring
that we only setup VTTBR_EL2 once on VHE. This cures an ugly race
that would lead to running with an unallocated VMID.
RISC-V:
- Fix hart status check in SBI HSM extension
- Fix hart suspend_type usage in SBI HSM extension
- Fix error returned by SBI IPI and TIME extensions for unsupported
function IDs
- Fix suspend_type usage in SBI SUSP extension
- Remove unnecessary vcpu kick after injecting interrupt via IMSIC
guest file
x86:
- Fix an nVMX bug where KVM fails to detect that, after nested
VM-Exit, L1 has a pending IRQ (or NMI).
- To avoid freeing the PIC while vCPUs are still around, which would
cause a NULL pointer access with the previous patch, destroy vCPUs
before any VM-level destruction.
- Handle failures to create vhost_tasks"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: retry nx_huge_page_recovery_thread creation
vhost: return task creation error instead of NULL
KVM: nVMX: Process events on nested VM-Exit if injectable IRQ or NMI is pending
KVM: x86: Free vCPUs before freeing VM state
riscv: KVM: Remove unnecessary vcpu kick
KVM: arm64: Ensure a VMID is allocated before programming VTTBR_EL2
KVM: arm64: Fix tcr_el2 initialisation in hVHE mode
riscv: KVM: Fix SBI sleep_type use
riscv: KVM: Fix SBI TIME error generation
riscv: KVM: Fix SBI IPI error generation
riscv: KVM: Fix hart suspend_type use
riscv: KVM: Fix hart suspend status check
This reverts commit cc77e2ce187d26cc66af3577bf896d7410eb25ab.
It was reported that adding ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives
breaks entering lower package states for certain systems.
It turns out that Samsung SSD 870 QVO actually has working LPM when using
a recent SSD firmware version.
The author of commit cc77e2ce187d ("ata: libata-core: Add ATA_QUIRK_NOLPM
for Samsung SSD 870 QVO drives") reported himself that only older SSD
firmware versions have broken LPM:
https://lore.kernel.org/stable/93c10d38-718c-459d-84a5-4d87680b4da7@debian.org/
Unfortunately, he did not specify which older firmware version he was using
which had broken LPM.
Let's revert this quirk, which has FW version field specified as NULL
(which means that it applies for all Samsung SSD 870 QVO firmware versions)
for now. Once the author reports which older firmware version(s) that are
broken, we can create a more fine grained quirk, which populates the FW
version field accordingly.
Fixes: cc77e2ce187d ("ata: libata-core: Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives")
Reported-by: Dieter Mummenschanz <dmummenschanz@web.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219747
Link: https://lore.kernel.org/r/20250228122603.91814-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The commit b1f8921dfbaa
("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
introduced a method to enable successive interrupts but inadvertently
omitted the necessary write to the EOI register, resulting in a failure to
receive successive interrupts.
Fix this by adding the required write to the EOI register.
Fixes: b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
Cc: stable@vger.kernel.org # v6.13+
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Fixes: 9b25419ad397 ("i2c: amd-asf: Add routine to handle the ASF slave process")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250219135747.3251182-1-Shyam-sundar.S-k@amd.com
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390
Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for some reported problems.
Nothing major, just:
- sc16is7xx irq check fix
- 8250 fifo underflow fix
- serial_port and 8250 iotype fixes
Most of these have been in linux-next already, and all have passed
0-day testing"
* tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: Fix fifo underflow on flush
serial: 8250_pnp: Remove unneeded ->iotype assignment
serial: 8250_platform: Remove unneeded ->iotype assignment
serial: 8250_of: Remove unneeded ->iotype assignment
serial: port: Make ->iotype validation global in __uart_read_properties()
serial: port: Always update ->iotype in __uart_read_properties()
serial: port: Assign ->iotype correctly when ->iobase is set
serial: sc16is7xx: Fix IRQ number check behavior
This introduces a module for working with faux devices in rust, along with
adding sample code to show how the API is used. Unlike other types of
devices, we don't provide any hooks for device probe/removal - since these
are optional for the faux API and are unnecessary in rust.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Maíra Canal <mairacanal@riseup.net>
Cc: Danilo Krummrich <dakr@kernel.org>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/2025021026-exert-accent-b4c6@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scripts/Makefile.clang was changed in the linked commit to move --target from
KBUILD_CFLAGS to KBUILD_CPPFLAGS, as that generally has a broader scope.
However that variable is not inspected by the userprogs logic,
breaking cross compilation on clang.
Use both variables to detect bitsize and target arguments for userprogs.
Fixes: feb843a469fb ("kbuild: add $(CLANG_FLAGS) to KBUILD_CPPFLAGS")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull x86 fixes from Ingo Molnar:
- Fix AVX-VNNI CPU feature dependency bug triggered via the 'noxsave'
boot option
- Fix typos in the SVA documentation
- Add Tony Luck as RDT co-maintainer and remove Fenghua Yu
* tag 'x86-urgent-2025-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
docs: arch/x86/sva: Fix two grammar errors under Background and FAQ
x86/cpufeatures: Make AVX-VNNI depend on AVX
MAINTAINERS: Change maintainer for RDT
Add check for the return value of cifs_buf_get() and cifs_small_buf_get()
in receive_encrypted_standard() to prevent null pointer dereference.
Fixes: eec04ea11969 ("smb: client: fix OOB in receive_encrypted_standard()")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The device tree of RK3568 did not specify reset-names before.
So add fallback to old behaviour to be compatible with old DT.
Fixes: fbcbffbac994 ("phy: rockchip: naneng-combphy: fix phy reset")
Cc: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250106100001.1344418-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Quite a few places want to build a struct qstr by given string;
it would be convenient to have a primitive doing that, rather
than open-coding it via QSTR_INIT().
The closest approximation was in bcachefs, but that expands to
initializer list - {.len = strlen(string), .name = string}.
It would be more useful to have it as compound literal -
(struct qstr){.len = strlen(string), .name = string}.
Unlike initializer list it's a valid expression. What's more,
it's a valid lvalue - it's an equivalent of anonymous local
variable with such initializer, so the things like
path->dentry = d_alloc_pseudo(mnt->mnt_sb, &QSTR(name));
are valid. It can also be used as initializer, with identical
effect -
struct qstr x = (struct qstr){.name = s, .len = strlen(s)};
is equivalent to
struct qstr anon_variable = {.name = s, .len = strlen(s)};
struct qstr x = anon_variable;
// anon_variable is never used after that point
and any even remotely sane compiler will manage to collapse that
into
struct qstr x = {.name = s, .len = strlen(s)};
What compound literals can't be used for is initialization of
global variables, but those are covered by QSTR_INIT().
This commit lifts definition(s) of QSTR() into linux/dcache.h,
converts it to compound literal (all bcachefs users are fine
with that) and converts assorted open-coded instances to using
that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 654102df2ac2 ("kbuild: add generic support for built-in
boot DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB when built-in DTB support is enabled.
To keep consistency across architectures, this commit also renames
CONFIG_USE_BUILTIN_DTB to CONFIG_BUILTIN_DTB, and
CONFIG_BUILTIN_DTB_SOURCE to CONFIG_BUILTIN_DTB_NAME.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
when turbostat interval mode can't migrate to a CPU, it complains,
prints no data, re-initializes with the new CPU configuration
and starts a new interval.
But this strategy in the face of a CPU hotplug offline during an interval
doesn't help in one-shot mode. When the missing CPU is discovered
at the end of the interval, the forked program has already returned
and there is nothing left for a new interval to measure.
So instead of aborting get_coutners() and delta_cpu() if a missing CPU
is detected, complain, but carry on and output what statistics are
actually present.
Use the same strategy for delta_cpu when aperf:mperf are observed
to have been reset -- complain, but carry on and print data for
the CPUs that are still present.
Interval mode error handling is unchanged.
One-shot mode can now do this:
$ sudo chcpu -e 1 ; sudo ./turbostat --quiet --show PkgWatt,Busy%,CPU chcpu -d 1
CPU 1 enabled
CPU 1 disabled
get_counters: Could not migrate to CPU 1
./turbostat: Counter reset detected
0.036920 sec
CPU Busy% PkgWatt
- 0.00 10.00
0 99.73 10.00
1 0.00
2 91.53
3 16.83
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull thermal control fixes from Rafael Wysocki:
"These fix the processing of DT thermal properties and the Power
Allocator thermal governor:
- Fix parsing cooling-maps in DT for trip points with more than one
cooling device (Rafael Wysocki)
- Fix granted_power computation in the Power Allocator thermal
governor and make it update total_weight on configuration changes
after the thermal zone has been registered (Yu-Che Cheng)"
* tag 'thermal-6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: gov_power_allocator: Update total_weight on bind and cdev updates
thermal/of: Fix cdev lookup in thermal_of_should_bind()
thermal: gov_power_allocator: Fix incorrect calculation in divvy_up_power()
A VMM may send a non-fatal signal to its threads, including vCPU tasks,
at any time, and thus may signal vCPU tasks during KVM_RUN. If a vCPU
task receives the signal while its trying to spawn the huge page recovery
vhost task, then KVM_RUN will fail due to copy_process() returning
-ERESTARTNOINTR.
Rework call_once() to mark the call complete if and only if the called
function succeeds, and plumb the function's true error code back to the
call_once() invoker. This provides userspace with the correct, non-fatal
error code so that the VMM doesn't terminate the VM on -ENOMEM, and allows
subsequent KVM_RUN a succeed by virtue of retrying creation of the NX huge
page task.
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
[implemented the kvm user side]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Message-ID: <20250227230631.303431-3-kbusch@meta.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port
numbers") added a skip to ahci_platform_enable_phys() for ports that are
not in mask_port_map.
The code in ahci_platform_get_resources(), will currently set mask_port_map
for each child "port" node it finds in the device tree.
However, device trees that do not have any child "port" nodes will not have
mask_port_map set, and for non-device tree platforms mask_port_map will
only exist as a quirk for specific PCI device + vendor IDs, or as a kernel
module parameter, but will not be set by default.
Therefore, the common thing is that mask_port_map is only set if you do not
want to use all ports (as defined by Offset 0Ch: PI – Ports Implemented
register), but instead only want to use the ports in mask_port_map. If
mask_port_map is not set, all ports are available.
Thus, ahci_ignore_port() must be able to handle an empty mask_port_map.
Fixes: 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port numbers")
Fixes: 2c202e6c4f4d ("ata: libahci_platform: Do not set mask_port_map when not needed")
Fixes: c9b5be909e65 ("ahci: Introduce ahci_ignore_port() helper")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-ide/10b31dd0-d0bb-4f76-9305-2195c3e17670@samsung.com/
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250225141612.942170-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn