tjh.dev
commits
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Ensure that direct mapping alias is always flushed when changing
page attributes. The optimization for small ranges failed to do so
when the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it
is guaranteed to only be called once during boot and cannot be
rearmed by clearing warn_once after boot. If it's invoked post boot
then lockdep rightfully complains about a potential deadlock as the
calling context is different.
- A series of fixes for objtool and the ORC unwinder addressing
variety of small issues:
- Stack offset tracking for indirect CFAs in objtool ignored
subsequent pushs and pops
- Repair the unwind hints in the register clearing entry ASM code
- Make the unwinding in the low level exit to usermode code stop
after switching to the trampoline stack. The unwind hint is no
longer valid and the ORC unwinder emits a warning as it can't
find the registers anymore.
- Fix unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
- Prevent unwinder warnings when dumping the stack of a
non-current task as there is no way to be sure about the
validity because the dumped stack can be a moving target.
- Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip
the first frame.
- Prevent ORC unwinding before ORC data has been initialized
- Immediately terminate unwinding when a unknown ORC entry type
is found.
- Prevent premature stop of the unwinder caused by IRET frames.
- Fix another infinite loop in objtool caused by a negative
offset which was not catched.
- Address a few build warnings in the ORC unwinder and add
missing static/ro_after_init annotations"
* tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Move ORC sorting variables under !CONFIG_MODULES
x86/apic: Move TSC deadline timer debug printk
ftrace/x86: Fix trace event registration for syscalls without arguments
x86/mm/cpa: Flush direct map alias during cpa
objtool: Fix infinite loop in for_offset_range()
x86/unwind/orc: Fix premature unwind stoppage due to IRET frames
x86/unwind/orc: Fix error path for bad ORC entry type
x86/unwind/orc: Prevent unwinding before ORC initialization
x86/unwind/orc: Don't skip the first frame for inactive tasks
x86/unwind: Prevent false warnings for non-current tasks
x86/unwind/orc: Convert global variables to static
x86/entry/64: Fix unwind hints in rewind_stack_do_exit()
x86/entry/64: Fix unwind hints in __switch_to_asm()
x86/entry/64: Fix unwind hints in kernel exit path
x86/entry/64: Fix unwind hints in register clearing code
objtool: Fix stack offset tracking for indirect CFAs
Pull objtool fix from Thomas Gleixner:
"A single fix for objtool to prevent an infinite loop in the
jump table search which can be triggered when building the
kernel with '-ffunction-sections'"
* tag 'objtool-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix infinite loop in find_jump_table()
Fix the following warnings seen with !CONFIG_MODULES:
arch/x86/kernel/unwind_orc.c:29:26: warning: 'cur_orc_table' defined but not used [-Wunused-variable]
29 | static struct orc_entry *cur_orc_table = __start_orc_unwind;
| ^~~~~~~~~~~~~
arch/x86/kernel/unwind_orc.c:28:13: warning: 'cur_orc_ip_table' defined but not used [-Wunused-variable]
28 | static int *cur_orc_ip_table = __start_orc_unwind_ip;
| ^~~~~~~~~~~~~~~~
Fixes: 153eb2223c79 ("x86/unwind/orc: Convert global variables to static")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linux Next Mailing List <linux-next@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200428071640.psn5m7eh3zt2in4v@treble
Pull locking fix from Thomas Gleixner:
"A single fix for the fallout of the recent futex uacess rework.
With those changes GCC9 fails to analyze arch_futex_atomic_op_inuser()
correctly and emits a 'maybe unitialized' warning. While we usually
ignore compiler stupidity the conditional store is pointless anyway
because the correct case has to store. For the fault case the extra
store does no harm"
* tag 'locking-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM: futex: Address build warning
Kristen found a hang in objtool when building with -ffunction-sections.
It was caused by evergreen_pcie_gen2_enable.cold() being laid out
immediately before evergreen_pcie_gen2_enable(). Since their "pfunc" is
always the same, find_jump_table() got into an infinite loop because it
didn't recognize the boundary between the two functions.
Fix that with a new prev_insn_same_sym() helper, which doesn't cross
subfunction boundaries.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/378b51c9d9c894dc3294bc460b4b0869e950b7c5.1588110291.git.jpoimboe@redhat.com
Leon reported that the printk_once() in __setup_APIC_LVTT() triggers a
lockdep splat due to a lock order violation between hrtimer_base::lock and
console_sem, when the 'once' condition is reset via
/sys/kernel/debug/clear_warn_once after boot.
The initial printk cannot trigger this because that happens during boot
when the local APIC timer is set up on the boot CPU.
Prevent it by moving the printk to a place which is guaranteed to be only
called once during boot.
Mark the deadline timer check related functions and data __init while at
it.
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/87y2qhoshi.fsf@nanos.tec.linutronix.de
Pull iommu fixes from Joerg Roedel:
- Race condition fixes for the AMD IOMMU driver.
These are five patches fixing two race conditions around
increase_address_space(). The first race condition was around the
non-atomic update of the domain page-table root pointer and the
variable containing the page-table depth (called mode). This is fixed
now be merging page-table root and mode into one 64-bit field which
is read/written atomically.
The second race condition was around updating the page-table root
pointer and making it public before the hardware caches were flushed.
This could cause addresses to be mapped and returned to drivers which
are not reachable by IOMMU hardware yet, causing IO page-faults. This
is fixed too by adding the necessary flushes before a new page-table
root is published.
Related to the race condition fixes these patches also add a missing
domain_flush_complete() barrier to update_domain() and a fix to bail
out of the loop which tries to increase the address space when the
call to increase_address_space() fails.
Qian was able to trigger the race conditions under high load and
memory pressure within a few days of testing. He confirmed that he
has seen no issues anymore with the fixes included here.
- Fix for a list-handling bug in the VirtIO IOMMU driver.
* tag 'iommu-fixes-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/virtio: Reverse arguments to list_add
iommu/amd: Do not flush Device Table in iommu_map_page()
iommu/amd: Update Device Table in increase_address_space()
iommu/amd: Call domain_flush_complete() in update_domain()
iommu/amd: Do not loop forever when trying to increase address space
iommu/amd: Fix race in increase_address_space()/fetch_pte()
Stephen reported the following build warning on a ARM multi_v7_defconfig
build with GCC 9.2.1:
kernel/futex.c: In function 'do_futex':
kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized]
1676 | return oldval == cmparg;
| ~~~~~~~^~~~~~~~~
kernel/futex.c:1652:6: note: 'oldval' was declared here
1652 | int oldval, ret;
| ^~~~~~
introduced by commit a08971e9488d ("futex: arch_futex_atomic_op_inuser()
calling conventions change").
While that change should not make any difference it confuses GCC which
fails to work out that oldval is not referenced when the return value is
not zero.
GCC fails to properly analyze arch_futex_atomic_op_inuser(). It's not the
early return, the issue is with the assembly macros. GCC fails to detect
that those either set 'ret' to 0 and set oldval or set 'ret' to -EFAULT
which makes oldval uninteresting. The store to the callsite supplied oldval
pointer is conditional on ret == 0.
The straight forward way to solve this is to make the store unconditional.
Aside of addressing the build warning this makes sense anyway because it
removes the conditional from the fastpath. In the error case the stored
value is uninteresting and the extra store does not matter at all.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/87pncao2ph.fsf@nanos.tec.linutronix.de
The refactoring of SYSCALL_DEFINE0() macros removed the ABI stubs and
simply defines __abi_sys_$NAME as alias of __do_sys_$NAME.
As a result kallsyms_lookup() returns "__do_sys_$NAME" which does not match
with the declared trace event name.
See also commit 1c758a2202a6 ("tracing/x86: Update syscall trace events to
handle new prefixed syscall func names").
Add __do_sys_ to the valid prefixes which are checked in
arch_syscall_match_sym_name().
Fixes: d2b5de495ee9 ("x86/entry: Refactor SYSCALL_DEFINE0 macros")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/158636958997.7900.16485049455470033557.stgit@buzz
Pull block fixes from Jens Axboe:
- a small series fixing a use-after-free of bdi name (Christoph,Yufen)
- NVMe fix for a regression with the smaller CQ update (Alexey)
- NVMe fix for a hang at namespace scanning error recovery (Sagi)
- fix race with blk-iocost iocg->abs_vdebt updates (Tejun)
* tag 'block-5.7-2020-05-09' of git://git.kernel.dk/linux-block:
nvme: fix possible hang when ns scanning fails during error recovery
nvme-pci: fix "slimmer CQ head update"
bdi: add a ->dev_name field to struct backing_dev_info
bdi: use bdi_dev_name() to get device name
bdi: move bdi_dev_name out of line
vboxsf: don't use the source name in the bdi name
iocost: protect iocg->abs_vdebt with iocg->waitq.lock
Elsewhere in the file, there is a list_for_each_entry with
&vdev->resv_regions as the second argument, suggesting that
&vdev->resv_regions is the list head. So exchange the
arguments on the list_add call to put the list head in the
second argument.
Fixes: 2a5a31487445 ("iommu/virtio: Add probe request")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/1588704467-13431-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull crypto fixes from Herbert Xu:
"This fixes a potential scheduling latency problem for the algorithms
used by WireGuard"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arch/nhpoly1305 - process in explicit 4k chunks
crypto: arch/lib - limit simd usage to 4k chunks
Pull more btrfs fixes from David Sterba:
"A few more stability fixes, minor build warning fixes and git url
fixup:
- fix partial loss of prealloc extent past i_size after fsync
- fix potential deadlock due to wrong transaction handle passing via
journal_info
- fix gcc 4.8 struct intialization warning
- update git URL in MAINTAINERS entry"
* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: btrfs: fix git repo URL
btrfs: fix gcc-4.8 build warning for struct initializer
btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info
btrfs: fix partial loss of prealloc extent past i_size after fsync
As an optimization, cpa_flush() was changed to optionally only flush
the range in @cpa if it was small enough. However, this range does
not include any direct map aliases changed in cpa_process_alias(). So
small set_memory_() calls that touch that alias don't get the direct
map changes flushed. This situation can happen when the virtual
address taking variants are passed an address in vmalloc or modules
space.
In these cases, force a full TLB flush.
Note this issue does not extend to cases where the set_memory_() calls are
passed a direct map address, or page array, etc, as the primary target. In
those cases the direct map would be flushed.
Fixes: 935f5839827e ("x86/mm/cpa: Optimize cpa_flush_array() TLB invalidation")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200424105343.GA20730@hirez.programming.kicks-ass.net
It seems that for whatever reason, gcc-10 ends up not inlining a couple
of functions that used to be inlined before. Even if they only have one
single callsite - it looks like gcc may have decided that the code was
unlikely, and not worth inlining.
The code generation difference is harmless, but caused a few new section
mismatch errors, since the (now no longer inlined) function wasn't in
the __init section, but called other init functions:
Section mismatch in reference from the function kexec_free_initrd() to the function .init.text:free_initrd_mem()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memremap()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memunmap()
So add the appropriate __init annotation to make modpost not complain.
In both cases there were trivially just a single callsite from another
__init function.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the controller is reconnecting, the host fails I/O and admin
commands as the host cannot reach the controller. ns scanning may
revalidate namespaces during that period and it is wrong to remove
namespaces due to these failures as we may hang (see 205da2434301).
One command that may fail is nvme_identify_ns_descs. Since we return
success due to having ns identify descriptor list optional, we continue
to compare ns identifiers in nvme_revalidate_disk, obviously fail and
return -ENODEV to nvme_validate_ns, which will remove the namespace.
Exactly what we don't want to happen.
Fixes: 22802bf742c2 ("nvme: Namepace identification descriptor list is optional")
Tested-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The flush of the Device Table Entries for the domain has already
happened in increase_address_space(), if necessary. Do no flush them
again in iommu_map_page().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-6-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull x86 platform driver fixes from Andy Shevchenko:
- Avoid loading asus-nb-wmi module on selected laptop models
- Fix S0ix debug support for Jasper Lake PMC
- Few fixes which have been reported by Hulk bot and others
* tag 'platform-drivers-x86-v5.7-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: Remove always false 'value < 0' statement
platform/x86: intel_pmc_core: avoid unused-function warnings
platform/x86: asus-nb-wmi: Do not load on Asus T100TA and T200TA
platform/x86: intel_pmc_core: Change Jasper Lake S0ix debug reg map back to ICL
platform/x86/intel-uncore-freq: make uncore_root_kobj static
platform/x86: wmi: Make two functions static
platform/x86: surface3_power: Fix a NULL vs IS_ERR() check in probe
Rather than chunking via PAGE_SIZE, this commit changes the arch
implementations to chunk in explicit 4k parts, so that calculations on
maximum acceptable latency don't suddenly become invalid on platforms
where PAGE_SIZE isn't 4k, such as arm64.
Fixes: 0f961f9f670e ("crypto: x86/nhpoly1305 - add AVX2 accelerated NHPoly1305")
Fixes: 012c82388c03 ("crypto: x86/nhpoly1305 - add SSE2 accelerated NHPoly1305")
Fixes: a00fa0c88774 ("crypto: arm64/nhpoly1305 - add NEON-accelerated NHPoly1305")
Fixes: 16aae3595a9d ("crypto: arm/nhpoly1305 - add NEON-accelerated NHPoly1305")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull IOMMU fixes from Joerg Roedel:
- Fix a memory leak when dev_iommu gets freed and a sub-pointer does
not
- Build dependency fixes for Mediatek, spapr_tce, and Intel IOMMU
driver
- Export iommu_group_get_for_dev() only for GPLed modules
- Fix AMD IOMMU interrupt remapping when x2apic is enabled
- Fix error path in the QCOM IOMMU driver probe function
* tag 'iommu-fixes-v5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/qcom: Fix local_base status check
iommu: Properly export iommu_group_get_for_dev()
iommu/vt-d: Use right Kconfig option name
iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system
iommu: spapr_tce: Disable compile testing to fix build on book3s_32 config
iommu/mediatek: Fix MTK_IOMMU dependencies
iommu: Fix the memory leak in dev_iommu_free()
The git repo listed for btrfs hasn't been updated in over a year.
List the current one instead.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Randy reported that objtool got stuck in an infinite loop when
processing drivers/i2c/busses/i2c-parport.o. It was caused by the
following code:
00000000000001fd <line_set>:
1fd: 48 b8 00 00 00 00 00 movabs $0x0,%rax
204: 00 00 00
1ff: R_X86_64_64 .rodata-0x8
207: 41 55 push %r13
209: 41 89 f5 mov %esi,%r13d
20c: 41 54 push %r12
20e: 49 89 fc mov %rdi,%r12
211: 55 push %rbp
212: 48 89 d5 mov %rdx,%rbp
215: 53 push %rbx
216: 0f b6 5a 01 movzbl 0x1(%rdx),%ebx
21a: 48 8d 34 dd 00 00 00 lea 0x0(,%rbx,8),%rsi
221: 00
21e: R_X86_64_32S .rodata
222: 48 89 f1 mov %rsi,%rcx
225: 48 29 c1 sub %rax,%rcx
find_jump_table() saw the .rodata reference and tried to find a jump
table associated with it (though there wasn't one). The -0x8 rela
addend is unusual. It caused find_jump_table() to send a negative
table_offset (unsigned 0xfffffffffffffff8) to find_rela_by_dest().
The negative offset should have been harmless, but it actually threw
for_offset_range() for a loop... literally. When the mask value got
incremented past the end value, it also wrapped to zero, causing the
loop exit condition to remain true forever.
Prevent this scenario from happening by ensuring the incremented value
is always >= the starting value.
Fixes: 74b873e49d92 ("objtool: Optimize find_rela_by_dest_range()")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Julien Thierry <jthierry@redhat.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/02b719674b031800b61e33c30b2e823183627c19.1587842122.git.jpoimboe@redhat.com
Pull RISC-V fixes from Palmer Dabbelt:
"A smattering of fixes and cleanups:
- Dead code removal.
- Exporting riscv_cpuid_to_hartid_mask for modules.
- Per-CPU tracking of ISA features.
- Setting max_pfn correctly when probing memory.
- Adding a note to the VDSO so glibc can check the kernel's version
without a uname().
- A fix to force the bootloader to initialize the boot spin tables,
which still get used as a fallback when SBI-0.1 is enabled"
* tag 'riscv-for-linus-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Remove unused code from STRICT_KERNEL_RWX
riscv: force __cpu_up_ variables to put in data section
riscv: add Linux note to vdso
riscv: set max_pfn to the PFN of the last page
RISC-V: Remove N-extension related defines
RISC-V: Add bitmap reprensenting ISA features common across CPUs
RISC-V: Export riscv_cpuid_to_hartid_mask() API
Pre-incrementing ->cq_head can't be done in memory because OOB value
can be observed by another context.
This devalues space savings compared to original code :-\
$ ./scripts/bloat-o-meter ../vmlinux-000 ../obj/vmlinux
add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-32 (-32)
Function old new delta
nvme_poll_irqdisable 464 456 -8
nvme_poll 455 447 -8
nvme_irq 388 380 -8
nvme_dev_disable 955 947 -8
But the code is minimal now: one read for head, one read for q_depth,
one increment, one comparison, single instruction phase bit update and
one write for new head.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: John Garry <john.garry@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Fixes: e2a366a4b0feaeb ("nvme-pci: slimmer CQ head update")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Device Table needs to be updated before the new page-table root
can be published in domain->pt_root. Otherwise a concurrent call to
fetch_pte might fetch a PTE which is not reachable through the Device
Table Entry.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-5-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull HID fixes from Jiri Kosina:
- Wacom driver functional and regression fixes from Jason Gerecke
- race condition fix in usbhid, found by syzbot and fixed by Alan Stern
- a few device-specific quirks and ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: quirks: Add HID_QUIRK_NO_INIT_REPORTS quirk for Dell K12A keyboard-dock
HID: mcp2221: add gpiolib dependency
HID: i2c-hid: reset Synaptics SYNA2393 on resume
HID: wacom: Report 2nd-gen Intuos Pro S center button status over BT
HID: usbhid: Fix race between usbhid_close() and usbhid_stop()
Revert "HID: wacom: generic: read the number of expected touches on a per collection basis"
HID: alps: ALPS_1657 is too specific; use U1_UNICORN_LEGACY instead
HID: alps: Add AUI1657 device ID
HID: logitech: Add support for Logitech G11 extra keys
HID: multitouch: add eGalaxTouch P80H84 support
HID: wacom: Read HID_DG_CONTACTMAX directly for non-generic devices
Since 'value' is declared as unsigned long, the following statement is
always false.
value < 0
So let's remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The initial Zinc patchset, after some mailing list discussion, contained
code to ensure that kernel_fpu_enable would not be kept on for more than
a 4k chunk, since it disables preemption. The choice of 4k isn't totally
scientific, but it's not a bad guess either, and it's what's used in
both the x86 poly1305, blake2s, and nhpoly1305 code already (in the form
of PAGE_SIZE, which this commit corrects to be explicitly 4k for the
former two).
Ard did some back of the envelope calculations and found that
at 5 cycles/byte (overestimate) on a 1ghz processor (pretty slow), 4k
means we have a maximum preemption disabling of 20us, which Sebastian
confirmed was probably a good limit.
Unfortunately the chunking appears to have been left out of the final
patchset that added the glue code. So, this commit adds it back in.
Fixes: 84e03fa39fbe ("crypto: x86/chacha - expose SIMD ChaCha routine as library function")
Fixes: b3aad5bad26a ("crypto: arm64/chacha - expose arm64 ChaCha routine as library function")
Fixes: a44a3430d71b ("crypto: arm/chacha - expose ARM ChaCha routine as library function")
Fixes: d7d7b8535662 ("crypto: x86/poly1305 - wire up faster implementations for kernel")
Fixes: f569ca164751 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Fixes: a6b803b3ddc7 ("crypto: arm/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Fixes: ed0356eda153 ("crypto: blake2s - x86_64 SIMD implementation")
Cc: Eric Biggers <ebiggers@google.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull power management fixes from Rafael Wysocki:
- prevent the intel_pstate driver from printing excessive diagnostic
messages in some cases (Chris Wilson)
- make the hibernation restore kernel freeze kernel threads as well as
user space tasks (Dexuan Cui)
- fix the ACPI device PM disagnostic messages to include the correct
power state name (Kai-Heng Feng).
* tag 'pm-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: ACPI: Output correct message on target power state
PM: hibernate: Freeze kernel threads in software_resume()
cpufreq: intel_pstate: Only mention the BIOS disabling turbo mode once
The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.
Fixes: 0ae349a0f33f ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200418134703.1760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some older compilers like gcc-4.8 warn about mismatched curly braces in
a initializer:
fs/btrfs/backref.c: In function 'is_shared_data_backref':
fs/btrfs/backref.c:394:9: error: missing braces around
initializer [-Werror=missing-braces]
struct prelim_ref target = {0};
^
fs/btrfs/backref.c:394:9: error: (near initialization for
'target.rbnode') [-Werror=missing-braces]
Use the GNU empty initializer extension to avoid this.
Fixes: ed58f2e66e84 ("btrfs: backref, don't add refs from shared block when resolving normal backref")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The following execution path is possible:
fsnotify()
[ realign the stack and store previous SP in R10 ]
<IRQ>
[ only IRET regs saved ]
common_interrupt()
interrupt_entry()
<NMI>
[ full pt_regs saved ]
...
[ unwind stack ]
When the unwinder goes through the NMI and the IRQ on the stack, and
then sees fsnotify(), it doesn't have access to the value of R10,
because it only has the five IRET registers. So the unwind stops
prematurely.
However, because the interrupt_entry() code is careful not to clobber
R10 before saving the full regs, the unwinder should be able to read R10
from the previously saved full pt_regs associated with the NMI.
Handle this case properly. When encountering an IRET regs frame
immediately after a full pt_regs frame, use the pt_regs as a backup
which can be used to get the C register values.
Also, note that a call frame resets the 'prev_regs' value, because a
function is free to clobber the registers. For this fix to work, the
IRET and full regs frames must be adjacent, with no FUNC frames in
between. So replace the FUNC hint in interrupt_entry() with an
IRET_REGS hint.
Fixes: ee9f8fce9964 ("x86/unwind: Add the ORC unwinder")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Jones <dsj@fb.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lore.kernel.org/r/97a408167cc09f1cfa0de31a7b70dd88868d743f.1587808742.git.jpoimboe@redhat.com
gcc-10 has started warning about conflicting types for a few new
built-in functions, particularly 'free()'.
This results in warnings like:
crypto/xts.c:325:13: warning: conflicting types for built-in function ‘free’; expected ‘void(void *)’ [-Wbuiltin-declaration-mismatch]
because the crypto layer had its local freeing functions called
'free()'.
Gcc-10 is in the wrong here, since that function is marked 'static', and
thus there is no chance of confusion with any standard library function
namespace.
But the simplest thing to do is to just use a different name here, and
avoid this gcc mis-feature.
[ Side note: gcc knowing about 'free()' is in itself not the
mis-feature: the semantics of 'free()' are special enough that a
compiler can validly do special things when seeing it.
So the mis-feature here is that gcc thinks that 'free()' is some
restricted name, and you can't shadow it as a local static function.
Making the special 'free()' semantics be a function attribute rather
than tied to the name would be the much better model ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the unused functions set_kernel_text_rw/ro.
Currently, it is not being invoked from anywhere and no other architecture
(except arm) uses this code. Even in ARM, these functions are not invoked
from anywhere currently.
Fixes: d27c3c90817e ("riscv: add STRICT_KERNEL_RWX support")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cache a copy of the name for the life time of the backing_dev_info
structure so that we can reference it even after unregistering.
Fixes: 68f23b89067f ("memcg: fix a crash in wb_workfn when a device disappears")
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The update_domain() function is expected to also inform the hardware
about domain changes. This needs a COMPLETION_WAIT command to be sent
to all IOMMUs which use the domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-4-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull gcc-plugins fixes from Kees Cook:
"GCC 10 fixes for gcc-plugins:
- Adjust caller of cgraph_create_edge for GCC 10 argument usage
- Update common headers to build under GCC 10 (Frédéric Pierret)"
* tag 'gcc-plugins-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-common.h: Update for GCC 10
gcc-plugins/stackleak: Avoid assignment for unused macro argument
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the Dell K12A keyboard-dock,
which can be used with various Dell Venue 11 models.
Without this quirk the keyboard/touchpad combo works fine when connected
at boot, but when hotplugged 9 out of 10 times it will not work properly.
Adding the quirk fixes this.
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When both CONFIG_DEBUG_FS and CONFIG_PM_SLEEP are disabled, the
functions that got moved out of the #ifdef section now cause
a warning:
drivers/platform/x86/intel_pmc_core.c:654:13: error: 'pmc_core_lpm_display' defined but not used [-Werror=unused-function]
654 | static void pmc_core_lpm_display(struct pmc_dev *pmcdev, struct device *dev,
| ^~~~~~~~~~~~~~~~~~~~
drivers/platform/x86/intel_pmc_core.c:617:13: error: 'pmc_core_slps0_display' defined but not used [-Werror=unused-function]
617 | static void pmc_core_slps0_display(struct pmc_dev *pmcdev, struct device *dev,
| ^~~~~~~~~~~~~~~~~~~~~~
Rather than add even more #ifdefs here, remove them entirely and
let the compiler work it out, it can actually get rid of all the
debugfs calls without problems as long as the struct member is
there.
The two PM functions just need a __maybe_unused annotations to avoid
another warning instead of the #ifdef.
Fixes: aae43c2bcdc1 ("platform/x86: intel_pmc_core: Relocate pmc_core_*_display() to outside of CONFIG_DEBUG_FS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For skcipher algorithms, the input, output HW S/G tables
look like this: [IV, src][dst, IV]
Now, we can have 2 conditions here:
- there is no IV;
- src and dst are equal (in-place encryption) and scattered
and the error is an "off-by-one" in the HW S/G table.
This issue was seen with KASAN:
BUG: KASAN: slab-out-of-bounds in skcipher_edesc_alloc+0x95c/0x1018
Read of size 4 at addr ffff000022a02958 by task cryptomgr_test/321
CPU: 2 PID: 321 Comm: cryptomgr_test Not tainted
5.6.0-rc1-00165-ge4ef8383-dirty #4
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load4+0x90/0xb0
skcipher_edesc_alloc+0x95c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Allocated by task 321:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
skcipher_edesc_alloc+0x21c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff000022a02800
which belongs to the cache dma-kmalloc-512 of size 512
The buggy address is located 344 bytes inside of
512-byte region [ffff000022a02800, ffff000022a02a00)
The buggy address belongs to the page:
page:fffffe00006a8000 refcount:1 mapcount:0 mapping:ffff00093200c400
index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c400
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000022a02800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff000022a02880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff000022a02900: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
^
ffff000022a02980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff000022a02a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 334d37c9e263 ("crypto: caam - update IV using HW support")
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull iomap fix from Darrick Wong:
"Hoist the check for an unrepresentable FIBMAP return value into
ioctl_fibmap.
The internal kernel function can handle 64-bit values (and is needed
to fix a regression on ext4 + jbd2). It is only the userspace ioctl
that is so old that it cannot deal"
* tag 'iomap-5.7-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fibmap: Warn and return an error in case of block > INT_MAX
* pm-cpufreq:
cpufreq: intel_pstate: Only mention the BIOS disabling turbo mode once
* pm-sleep:
PM: hibernate: Freeze kernel threads in software_resume()
In commit a7ba5c3d008d ("drivers/iommu: Export core IOMMU API symbols to
permit modular drivers") a bunch of iommu symbols were exported, all
with _GPL markings except iommu_group_get_for_dev(). That export should
also be _GPL like the others.
Fixes: a7ba5c3d008d ("drivers/iommu: Export core IOMMU API symbols to permit modular drivers")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200430120120.2948448-1-gregkh@linuxfoundation.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
[BUG]
One run of btrfs/063 triggered the following lockdep warning:
============================================
WARNING: possible recursive locking detected
5.6.0-rc7-custom+ #48 Not tainted
--------------------------------------------
kworker/u24:0/7 is trying to acquire lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
but task is already holding lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sb_internal#2);
lock(sb_internal#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u24:0/7:
#0: ffff88817b495948 ((wq_completion)btrfs-endio-write){+.+.}, at: process_one_work+0x557/0xb80
#1: ffff888189ea7db8 ((work_completion)(&work->normal_work)){+.+.}, at: process_one_work+0x557/0xb80
#2: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
#3: ffff888174ca4da8 (&fs_info->reloc_mutex){+.+.}, at: btrfs_record_root_in_trans+0x83/0xd0 [btrfs]
stack backtrace:
CPU: 0 PID: 7 Comm: kworker/u24:0 Not tainted 5.6.0-rc7-custom+ #48
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
Call Trace:
dump_stack+0xc2/0x11a
__lock_acquire.cold+0xce/0x214
lock_acquire+0xe6/0x210
__sb_start_write+0x14e/0x290
start_transaction+0x66c/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
find_free_extent+0x1504/0x1a50 [btrfs]
btrfs_reserve_extent+0xd5/0x1f0 [btrfs]
btrfs_alloc_tree_block+0x1ac/0x570 [btrfs]
btrfs_copy_root+0x213/0x580 [btrfs]
create_reloc_root+0x3bd/0x470 [btrfs]
btrfs_init_reloc_root+0x2d2/0x310 [btrfs]
record_root_in_trans+0x191/0x1d0 [btrfs]
btrfs_record_root_in_trans+0x90/0xd0 [btrfs]
start_transaction+0x16e/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
btrfs_finish_ordered_io+0x55d/0xcd0 [btrfs]
finish_ordered_fn+0x15/0x20 [btrfs]
btrfs_work_helper+0x116/0x9a0 [btrfs]
process_one_work+0x632/0xb80
worker_thread+0x80/0x690
kthread+0x1a3/0x1f0
ret_from_fork+0x27/0x50
It's pretty hard to reproduce, only one hit so far.
[CAUSE]
This is because we're calling btrfs_join_transaction() without re-using
the current running one:
btrfs_finish_ordered_io()
|- btrfs_join_transaction() <<< Call #1
|- btrfs_record_root_in_trans()
|- btrfs_reserve_extent()
|- btrfs_join_transaction() <<< Call #2
Normally such btrfs_join_transaction() call should re-use the existing
one, without trying to re-start a transaction.
But the problem is, in btrfs_join_transaction() call #1, we call
btrfs_record_root_in_trans() before initializing current::journal_info.
And in btrfs_join_transaction() call #2, we're relying on
current::journal_info to avoid such deadlock.
[FIX]
Call btrfs_record_root_in_trans() after we have initialized
current::journal_info.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If the ORC entry type is unknown, nothing else can be done other than
reporting an error. Exit the function instead of breaking out of the
switch statement.
Fixes: ee9f8fce9964 ("x86/unwind: Add the ORC unwinder")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Jones <dsj@fb.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lore.kernel.org/r/a7fa668ca6eabbe81ab18b2424f15adbbfdc810a.1587808742.git.jpoimboe@redhat.com
gcc-10 now warns about passing aliasing pointers to functions that take
restricted pointers.
That's actually a great warning, and if we ever start using 'restrict'
in the kernel, it might be quite useful. But right now we don't, and it
turns out that the only thing this warns about is an idiom where we have
declared a few functions to be "printf-like" (which seems to make gcc
pick up the restricted pointer thing), and then we print to the same
buffer that we also use as an input.
And people do that as an odd concatenation pattern, with code like this:
#define sysfs_show_gen_prop(buffer, fmt, ...) \
snprintf(buffer, PAGE_SIZE, "%s"fmt, buffer, __VA_ARGS__)
where we have 'buffer' as both the destination of the final result, and
as the initial argument.
Yes, it's a bit questionable. And outside of the kernel, people do have
standard declarations like
int snprintf( char *restrict buffer, size_t bufsz,
const char *restrict format, ... );
where that output buffer is marked as a restrict pointer that cannot
alias with any other arguments.
But in the context of the kernel, that 'use snprintf() to concatenate to
the end result' does work, and the pattern shows up in multiple places.
And we have not marked our own version of snprintf() as taking restrict
pointers, so the warning is incorrect for now, and gcc picks it up on
its own.
If we do start using 'restrict' in the kernel (and it might be a good
idea if people find places where it matters), we'll need to figure out
how to avoid this issue for snprintf and friends. But in the meantime,
this warning is not useful.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put __cpu_up_stack_pointer and __cpu_up_task_pointer in data section.
Currently, these two variables are put in bss section, there is a
potential risk that secondary harts get the uninitialized value before
main hart finishing the bss clearing. In this case, all secondary
harts would pass the waiting loop and enable the MMU before main hart
set up the page table.
This issue happens on random booting of multiple harts, which means
it will manifest for BBL and OpenSBI v0.6 (or older version). In OpenSBI
v0.7 (or higher version), we have HSM extension so all the secondary harts
are brought-up by Linux kernel in an orderly fashion. This means we don't
need this change for OpenSBI v0.7 (or higher version).
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Use the common interface bdi_dev_name() to get device name.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Add missing <linux/backing-dev.h> include BFQ
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When increase_address_space() fails to allocate memory, alloc_pte()
will call it again until it succeeds. Do not loop forever while trying
to increase the address space and just return an error instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull virtio fixes from Michael Tsirkin:
"A couple of bug fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: vsock: kick send_pkt worker once device is started
virtio-blk: handle block_device_operations callbacks after hot unplug
Remove "params.h" include, which has been dropped in GCC 10.
Remove is_a_helper() macro, which is now defined in gimple.h, as seen
when running './scripts/gcc-plugin.sh g++ g++ gcc':
In file included from <stdin>:1:
./gcc-plugins/gcc-common.h:852:13: error: redefinition of ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’
852 | inline bool is_a_helper<const ggoto *>::test(const_gimple gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from ./gcc-plugins/gcc-common.h:125,
from <stdin>:1:
/usr/lib/gcc/x86_64-redhat-linux/10/plugin/include/gimple.h:1037:1: note: ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’ previously declared here
1037 | is_a_helper <const ggoto *>::test (const gimple *gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Add -Wno-format-diag to scripts/gcc-plugins/Makefile to avoid
meaningless warnings from error() formats used by plugins:
scripts/gcc-plugins/structleak_plugin.c: In function ‘int plugin_init(plugin_name_args*, plugin_gcc_version*)’:
scripts/gcc-plugins/structleak_plugin.c:253:12: warning: unquoted sequence of 2 consecutive punctuation characters ‘'-’ in format [-Wformat-diag]
253 | error(G_("unknown option '-fplugin-arg-%s-%s'"), plugin_name, argv[i].key);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Frédéric Pierret (fepitre) <frederic.pierret@qubes-os.org>
Link: https://lore.kernel.org/r/20200407113259.270172-1-frederic.pierret@qubes-os.org
[kees: include -Wno-format-diag for plugin builds]
Signed-off-by: Kees Cook <keescook@chromium.org>
Without gpiolib, this driver fails to link:
arm-linux-gnueabi-ld: drivers/hid/hid-mcp2221.o: in function `mcp2221_probe':
hid-mcp2221.c:(.text+0x1b0): undefined reference to `devm_gpiochip_add_data'
arm-linux-gnueabi-ld: drivers/hid/hid-mcp2221.o: in function `mcp_gpio_get':
hid-mcp2221.c:(.text+0x30c): undefined reference to `gpiochip_get_data'
Fixes: 328de1c519c5 ("HID: mcp2221: add GPIO functionality support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
asus-nb-wmi does not add any extra functionality on these Asus
Transformer books. They have detachable keyboards, so the hotkeys are
send through a HID device (and handled by the hid-asus driver) and also
the rfkill functionality is not used on these devices.
Besides not adding any extra functionality, initializing the WMI interface
on these devices actually has a negative side-effect. For some reason
the \_SB.ATKD.INIT() function which asus_wmi_platform_init() calls drives
GPO2 (INT33FC:02) pin 8, which is connected to the front facing webcam LED,
high and there is no (WMI or other) interface to drive this low again
causing the LED to be permanently on, even during suspend.
This commit adds a blacklist of DMI system_ids on which not to load the
asus-nb-wmi and adds these Transformer books to this list. This fixes
the webcam LED being permanently on under Linux.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Here's the KASAN report:
BUG: KASAN: use-after-free in rsa_pub_done+0x70/0xe8
Read of size 1 at addr ffff000023082014 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #60
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
rsa_pub_done+0x70/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
cpuidle_enter_state+0xa4/0x490
cpuidle_enter+0x48/0x70
call_cpuidle+0x44/0x70
do_idle+0x304/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
rsa_edesc_alloc+0x2cc/0xe10
caam_rsa_enc+0x9c/0x5f0
test_akcipher_one+0x78c/0x968
alg_test_akcipher+0x78/0xf8
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
rsa_pub_done+0x68/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff000023082000
which belongs to the cache dma-kmalloc-256 of size 256
The buggy address is located 20 bytes inside of
256-byte region [ffff000023082000, ffff000023082100)
The buggy address belongs to the page:
page:fffffe00006c2080 refcount:1 mapcount:0 mapping:ffff00093200c200 index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c200
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000023081f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff000023081f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff000023082000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff000023082080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff000023082100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: bf53795025a2 ("crypto: caam - add crypto_engine support for RSA algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes:
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect
requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups:
- Remove unreachable error conditions"
* tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a race in __nfs_list_for_each_server()
NFSv4.1: fix handling of backchannel binding in BIND_CONN_TO_SESSION
SUNRPC: defer slow parts of rpc_free_client() to a workqueue.
NFSv4: Remove unreachable error condition due to rpc_run_task()
SUNRPC: Remove unreachable error condition
xprtrdma: Fix use of xdr_stream_encode_item_{present, absent}
xprtrdma: Fix trace point use-after-free race
xprtrdma: Restore wake-up-all to rpcrdma_cm_event_handler()
nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl
NFS/pnfs: Fix a credential use-after-free issue in pnfs_roc()
NFS/pnfs: Ensure that _pnfs_return_layout() waits for layoutreturn completion
We better warn the fibmap user and not return a truncated and therefore
an incorrect block map address if the bmap() returned block address
is greater than INT_MAX (since user supplied integer pointer).
It's better to pr_warn() all user of ioctl_fibmap() and return a proper
error code rather than silently letting a FS corruption happen if the
user tries to fiddle around with the returned block map address.
We fix this by returning an error code of -ERANGE and returning 0 as the
block mapping address in case if it is > INT_MAX.
Now iomap_bmap() could be called from either of these two paths.
Either when a user is calling an ioctl_fibmap() interface to get
the block mapping address or by some filesystem via use of bmap()
internal kernel API.
bmap() kernel API is well equipped with handling of u64 addresses.
WARN condition in iomap_bmap_actor() was mainly added to warn all
the fibmap users. But now that we have directly added this warning
for all fibmap users and also made sure to return 0 as block map address
in case if addr > INT_MAX.
So we can now remove this logic from iomap_bmap_actor().
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Transitioned power state logged at the end of setting ACPI power.
However, D3cold won't be in the message because state can only be
D3hot at most.
Use target_state to corretly report when power state is D3cold.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make a note of the first time we discover the turbo mode has been
disabled by the BIOS, as otherwise we complain every time we try to
update the mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Ensure that direct mapping alias is always flushed when changing
page attributes. The optimization for small ranges failed to do so
when the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it
is guaranteed to only be called once during boot and cannot be
rearmed by clearing warn_once after boot. If it's invoked post boot
then lockdep rightfully complains about a potential deadlock as the
calling context is different.
- A series of fixes for objtool and the ORC unwinder addressing
variety of small issues:
- Stack offset tracking for indirect CFAs in objtool ignored
subsequent pushs and pops
- Repair the unwind hints in the register clearing entry ASM code
- Make the unwinding in the low level exit to usermode code stop
after switching to the trampoline stack. The unwind hint is no
longer valid and the ORC unwinder emits a warning as it can't
find the registers anymore.
- Fix unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
- Prevent unwinder warnings when dumping the stack of a
non-current task as there is no way to be sure about the
validity because the dumped stack can be a moving target.
- Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip
the first frame.
- Prevent ORC unwinding before ORC data has been initialized
- Immediately terminate unwinding when a unknown ORC entry type
is found.
- Prevent premature stop of the unwinder caused by IRET frames.
- Fix another infinite loop in objtool caused by a negative
offset which was not catched.
- Address a few build warnings in the ORC unwinder and add
missing static/ro_after_init annotations"
* tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Move ORC sorting variables under !CONFIG_MODULES
x86/apic: Move TSC deadline timer debug printk
ftrace/x86: Fix trace event registration for syscalls without arguments
x86/mm/cpa: Flush direct map alias during cpa
objtool: Fix infinite loop in for_offset_range()
x86/unwind/orc: Fix premature unwind stoppage due to IRET frames
x86/unwind/orc: Fix error path for bad ORC entry type
x86/unwind/orc: Prevent unwinding before ORC initialization
x86/unwind/orc: Don't skip the first frame for inactive tasks
x86/unwind: Prevent false warnings for non-current tasks
x86/unwind/orc: Convert global variables to static
x86/entry/64: Fix unwind hints in rewind_stack_do_exit()
x86/entry/64: Fix unwind hints in __switch_to_asm()
x86/entry/64: Fix unwind hints in kernel exit path
x86/entry/64: Fix unwind hints in register clearing code
objtool: Fix stack offset tracking for indirect CFAs
Pull objtool fix from Thomas Gleixner:
"A single fix for objtool to prevent an infinite loop in the
jump table search which can be triggered when building the
kernel with '-ffunction-sections'"
* tag 'objtool-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix infinite loop in find_jump_table()
Fix the following warnings seen with !CONFIG_MODULES:
arch/x86/kernel/unwind_orc.c:29:26: warning: 'cur_orc_table' defined but not used [-Wunused-variable]
29 | static struct orc_entry *cur_orc_table = __start_orc_unwind;
| ^~~~~~~~~~~~~
arch/x86/kernel/unwind_orc.c:28:13: warning: 'cur_orc_ip_table' defined but not used [-Wunused-variable]
28 | static int *cur_orc_ip_table = __start_orc_unwind_ip;
| ^~~~~~~~~~~~~~~~
Fixes: 153eb2223c79 ("x86/unwind/orc: Convert global variables to static")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linux Next Mailing List <linux-next@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200428071640.psn5m7eh3zt2in4v@treble
Pull locking fix from Thomas Gleixner:
"A single fix for the fallout of the recent futex uacess rework.
With those changes GCC9 fails to analyze arch_futex_atomic_op_inuser()
correctly and emits a 'maybe unitialized' warning. While we usually
ignore compiler stupidity the conditional store is pointless anyway
because the correct case has to store. For the fault case the extra
store does no harm"
* tag 'locking-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM: futex: Address build warning
Kristen found a hang in objtool when building with -ffunction-sections.
It was caused by evergreen_pcie_gen2_enable.cold() being laid out
immediately before evergreen_pcie_gen2_enable(). Since their "pfunc" is
always the same, find_jump_table() got into an infinite loop because it
didn't recognize the boundary between the two functions.
Fix that with a new prev_insn_same_sym() helper, which doesn't cross
subfunction boundaries.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/378b51c9d9c894dc3294bc460b4b0869e950b7c5.1588110291.git.jpoimboe@redhat.com
Leon reported that the printk_once() in __setup_APIC_LVTT() triggers a
lockdep splat due to a lock order violation between hrtimer_base::lock and
console_sem, when the 'once' condition is reset via
/sys/kernel/debug/clear_warn_once after boot.
The initial printk cannot trigger this because that happens during boot
when the local APIC timer is set up on the boot CPU.
Prevent it by moving the printk to a place which is guaranteed to be only
called once during boot.
Mark the deadline timer check related functions and data __init while at
it.
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/87y2qhoshi.fsf@nanos.tec.linutronix.de
Pull iommu fixes from Joerg Roedel:
- Race condition fixes for the AMD IOMMU driver.
These are five patches fixing two race conditions around
increase_address_space(). The first race condition was around the
non-atomic update of the domain page-table root pointer and the
variable containing the page-table depth (called mode). This is fixed
now be merging page-table root and mode into one 64-bit field which
is read/written atomically.
The second race condition was around updating the page-table root
pointer and making it public before the hardware caches were flushed.
This could cause addresses to be mapped and returned to drivers which
are not reachable by IOMMU hardware yet, causing IO page-faults. This
is fixed too by adding the necessary flushes before a new page-table
root is published.
Related to the race condition fixes these patches also add a missing
domain_flush_complete() barrier to update_domain() and a fix to bail
out of the loop which tries to increase the address space when the
call to increase_address_space() fails.
Qian was able to trigger the race conditions under high load and
memory pressure within a few days of testing. He confirmed that he
has seen no issues anymore with the fixes included here.
- Fix for a list-handling bug in the VirtIO IOMMU driver.
* tag 'iommu-fixes-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/virtio: Reverse arguments to list_add
iommu/amd: Do not flush Device Table in iommu_map_page()
iommu/amd: Update Device Table in increase_address_space()
iommu/amd: Call domain_flush_complete() in update_domain()
iommu/amd: Do not loop forever when trying to increase address space
iommu/amd: Fix race in increase_address_space()/fetch_pte()
Stephen reported the following build warning on a ARM multi_v7_defconfig
build with GCC 9.2.1:
kernel/futex.c: In function 'do_futex':
kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized]
1676 | return oldval == cmparg;
| ~~~~~~~^~~~~~~~~
kernel/futex.c:1652:6: note: 'oldval' was declared here
1652 | int oldval, ret;
| ^~~~~~
introduced by commit a08971e9488d ("futex: arch_futex_atomic_op_inuser()
calling conventions change").
While that change should not make any difference it confuses GCC which
fails to work out that oldval is not referenced when the return value is
not zero.
GCC fails to properly analyze arch_futex_atomic_op_inuser(). It's not the
early return, the issue is with the assembly macros. GCC fails to detect
that those either set 'ret' to 0 and set oldval or set 'ret' to -EFAULT
which makes oldval uninteresting. The store to the callsite supplied oldval
pointer is conditional on ret == 0.
The straight forward way to solve this is to make the store unconditional.
Aside of addressing the build warning this makes sense anyway because it
removes the conditional from the fastpath. In the error case the stored
value is uninteresting and the extra store does not matter at all.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/87pncao2ph.fsf@nanos.tec.linutronix.de
The refactoring of SYSCALL_DEFINE0() macros removed the ABI stubs and
simply defines __abi_sys_$NAME as alias of __do_sys_$NAME.
As a result kallsyms_lookup() returns "__do_sys_$NAME" which does not match
with the declared trace event name.
See also commit 1c758a2202a6 ("tracing/x86: Update syscall trace events to
handle new prefixed syscall func names").
Add __do_sys_ to the valid prefixes which are checked in
arch_syscall_match_sym_name().
Fixes: d2b5de495ee9 ("x86/entry: Refactor SYSCALL_DEFINE0 macros")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/158636958997.7900.16485049455470033557.stgit@buzz
Pull block fixes from Jens Axboe:
- a small series fixing a use-after-free of bdi name (Christoph,Yufen)
- NVMe fix for a regression with the smaller CQ update (Alexey)
- NVMe fix for a hang at namespace scanning error recovery (Sagi)
- fix race with blk-iocost iocg->abs_vdebt updates (Tejun)
* tag 'block-5.7-2020-05-09' of git://git.kernel.dk/linux-block:
nvme: fix possible hang when ns scanning fails during error recovery
nvme-pci: fix "slimmer CQ head update"
bdi: add a ->dev_name field to struct backing_dev_info
bdi: use bdi_dev_name() to get device name
bdi: move bdi_dev_name out of line
vboxsf: don't use the source name in the bdi name
iocost: protect iocg->abs_vdebt with iocg->waitq.lock
Elsewhere in the file, there is a list_for_each_entry with
&vdev->resv_regions as the second argument, suggesting that
&vdev->resv_regions is the list head. So exchange the
arguments on the list_add call to put the list head in the
second argument.
Fixes: 2a5a31487445 ("iommu/virtio: Add probe request")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/1588704467-13431-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull crypto fixes from Herbert Xu:
"This fixes a potential scheduling latency problem for the algorithms
used by WireGuard"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arch/nhpoly1305 - process in explicit 4k chunks
crypto: arch/lib - limit simd usage to 4k chunks
Pull more btrfs fixes from David Sterba:
"A few more stability fixes, minor build warning fixes and git url
fixup:
- fix partial loss of prealloc extent past i_size after fsync
- fix potential deadlock due to wrong transaction handle passing via
journal_info
- fix gcc 4.8 struct intialization warning
- update git URL in MAINTAINERS entry"
* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: btrfs: fix git repo URL
btrfs: fix gcc-4.8 build warning for struct initializer
btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info
btrfs: fix partial loss of prealloc extent past i_size after fsync
As an optimization, cpa_flush() was changed to optionally only flush
the range in @cpa if it was small enough. However, this range does
not include any direct map aliases changed in cpa_process_alias(). So
small set_memory_() calls that touch that alias don't get the direct
map changes flushed. This situation can happen when the virtual
address taking variants are passed an address in vmalloc or modules
space.
In these cases, force a full TLB flush.
Note this issue does not extend to cases where the set_memory_() calls are
passed a direct map address, or page array, etc, as the primary target. In
those cases the direct map would be flushed.
Fixes: 935f5839827e ("x86/mm/cpa: Optimize cpa_flush_array() TLB invalidation")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200424105343.GA20730@hirez.programming.kicks-ass.net
It seems that for whatever reason, gcc-10 ends up not inlining a couple
of functions that used to be inlined before. Even if they only have one
single callsite - it looks like gcc may have decided that the code was
unlikely, and not worth inlining.
The code generation difference is harmless, but caused a few new section
mismatch errors, since the (now no longer inlined) function wasn't in
the __init section, but called other init functions:
Section mismatch in reference from the function kexec_free_initrd() to the function .init.text:free_initrd_mem()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memremap()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memunmap()
So add the appropriate __init annotation to make modpost not complain.
In both cases there were trivially just a single callsite from another
__init function.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the controller is reconnecting, the host fails I/O and admin
commands as the host cannot reach the controller. ns scanning may
revalidate namespaces during that period and it is wrong to remove
namespaces due to these failures as we may hang (see 205da2434301).
One command that may fail is nvme_identify_ns_descs. Since we return
success due to having ns identify descriptor list optional, we continue
to compare ns identifiers in nvme_revalidate_disk, obviously fail and
return -ENODEV to nvme_validate_ns, which will remove the namespace.
Exactly what we don't want to happen.
Fixes: 22802bf742c2 ("nvme: Namepace identification descriptor list is optional")
Tested-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The flush of the Device Table Entries for the domain has already
happened in increase_address_space(), if necessary. Do no flush them
again in iommu_map_page().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-6-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull x86 platform driver fixes from Andy Shevchenko:
- Avoid loading asus-nb-wmi module on selected laptop models
- Fix S0ix debug support for Jasper Lake PMC
- Few fixes which have been reported by Hulk bot and others
* tag 'platform-drivers-x86-v5.7-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: Remove always false 'value < 0' statement
platform/x86: intel_pmc_core: avoid unused-function warnings
platform/x86: asus-nb-wmi: Do not load on Asus T100TA and T200TA
platform/x86: intel_pmc_core: Change Jasper Lake S0ix debug reg map back to ICL
platform/x86/intel-uncore-freq: make uncore_root_kobj static
platform/x86: wmi: Make two functions static
platform/x86: surface3_power: Fix a NULL vs IS_ERR() check in probe
Rather than chunking via PAGE_SIZE, this commit changes the arch
implementations to chunk in explicit 4k parts, so that calculations on
maximum acceptable latency don't suddenly become invalid on platforms
where PAGE_SIZE isn't 4k, such as arm64.
Fixes: 0f961f9f670e ("crypto: x86/nhpoly1305 - add AVX2 accelerated NHPoly1305")
Fixes: 012c82388c03 ("crypto: x86/nhpoly1305 - add SSE2 accelerated NHPoly1305")
Fixes: a00fa0c88774 ("crypto: arm64/nhpoly1305 - add NEON-accelerated NHPoly1305")
Fixes: 16aae3595a9d ("crypto: arm/nhpoly1305 - add NEON-accelerated NHPoly1305")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull IOMMU fixes from Joerg Roedel:
- Fix a memory leak when dev_iommu gets freed and a sub-pointer does
not
- Build dependency fixes for Mediatek, spapr_tce, and Intel IOMMU
driver
- Export iommu_group_get_for_dev() only for GPLed modules
- Fix AMD IOMMU interrupt remapping when x2apic is enabled
- Fix error path in the QCOM IOMMU driver probe function
* tag 'iommu-fixes-v5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/qcom: Fix local_base status check
iommu: Properly export iommu_group_get_for_dev()
iommu/vt-d: Use right Kconfig option name
iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system
iommu: spapr_tce: Disable compile testing to fix build on book3s_32 config
iommu/mediatek: Fix MTK_IOMMU dependencies
iommu: Fix the memory leak in dev_iommu_free()
Randy reported that objtool got stuck in an infinite loop when
processing drivers/i2c/busses/i2c-parport.o. It was caused by the
following code:
00000000000001fd <line_set>:
1fd: 48 b8 00 00 00 00 00 movabs $0x0,%rax
204: 00 00 00
1ff: R_X86_64_64 .rodata-0x8
207: 41 55 push %r13
209: 41 89 f5 mov %esi,%r13d
20c: 41 54 push %r12
20e: 49 89 fc mov %rdi,%r12
211: 55 push %rbp
212: 48 89 d5 mov %rdx,%rbp
215: 53 push %rbx
216: 0f b6 5a 01 movzbl 0x1(%rdx),%ebx
21a: 48 8d 34 dd 00 00 00 lea 0x0(,%rbx,8),%rsi
221: 00
21e: R_X86_64_32S .rodata
222: 48 89 f1 mov %rsi,%rcx
225: 48 29 c1 sub %rax,%rcx
find_jump_table() saw the .rodata reference and tried to find a jump
table associated with it (though there wasn't one). The -0x8 rela
addend is unusual. It caused find_jump_table() to send a negative
table_offset (unsigned 0xfffffffffffffff8) to find_rela_by_dest().
The negative offset should have been harmless, but it actually threw
for_offset_range() for a loop... literally. When the mask value got
incremented past the end value, it also wrapped to zero, causing the
loop exit condition to remain true forever.
Prevent this scenario from happening by ensuring the incremented value
is always >= the starting value.
Fixes: 74b873e49d92 ("objtool: Optimize find_rela_by_dest_range()")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Julien Thierry <jthierry@redhat.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/02b719674b031800b61e33c30b2e823183627c19.1587842122.git.jpoimboe@redhat.com
Pull RISC-V fixes from Palmer Dabbelt:
"A smattering of fixes and cleanups:
- Dead code removal.
- Exporting riscv_cpuid_to_hartid_mask for modules.
- Per-CPU tracking of ISA features.
- Setting max_pfn correctly when probing memory.
- Adding a note to the VDSO so glibc can check the kernel's version
without a uname().
- A fix to force the bootloader to initialize the boot spin tables,
which still get used as a fallback when SBI-0.1 is enabled"
* tag 'riscv-for-linus-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Remove unused code from STRICT_KERNEL_RWX
riscv: force __cpu_up_ variables to put in data section
riscv: add Linux note to vdso
riscv: set max_pfn to the PFN of the last page
RISC-V: Remove N-extension related defines
RISC-V: Add bitmap reprensenting ISA features common across CPUs
RISC-V: Export riscv_cpuid_to_hartid_mask() API
Pre-incrementing ->cq_head can't be done in memory because OOB value
can be observed by another context.
This devalues space savings compared to original code :-\
$ ./scripts/bloat-o-meter ../vmlinux-000 ../obj/vmlinux
add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-32 (-32)
Function old new delta
nvme_poll_irqdisable 464 456 -8
nvme_poll 455 447 -8
nvme_irq 388 380 -8
nvme_dev_disable 955 947 -8
But the code is minimal now: one read for head, one read for q_depth,
one increment, one comparison, single instruction phase bit update and
one write for new head.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: John Garry <john.garry@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Fixes: e2a366a4b0feaeb ("nvme-pci: slimmer CQ head update")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Device Table needs to be updated before the new page-table root
can be published in domain->pt_root. Otherwise a concurrent call to
fetch_pte might fetch a PTE which is not reachable through the Device
Table Entry.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-5-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull HID fixes from Jiri Kosina:
- Wacom driver functional and regression fixes from Jason Gerecke
- race condition fix in usbhid, found by syzbot and fixed by Alan Stern
- a few device-specific quirks and ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: quirks: Add HID_QUIRK_NO_INIT_REPORTS quirk for Dell K12A keyboard-dock
HID: mcp2221: add gpiolib dependency
HID: i2c-hid: reset Synaptics SYNA2393 on resume
HID: wacom: Report 2nd-gen Intuos Pro S center button status over BT
HID: usbhid: Fix race between usbhid_close() and usbhid_stop()
Revert "HID: wacom: generic: read the number of expected touches on a per collection basis"
HID: alps: ALPS_1657 is too specific; use U1_UNICORN_LEGACY instead
HID: alps: Add AUI1657 device ID
HID: logitech: Add support for Logitech G11 extra keys
HID: multitouch: add eGalaxTouch P80H84 support
HID: wacom: Read HID_DG_CONTACTMAX directly for non-generic devices
The initial Zinc patchset, after some mailing list discussion, contained
code to ensure that kernel_fpu_enable would not be kept on for more than
a 4k chunk, since it disables preemption. The choice of 4k isn't totally
scientific, but it's not a bad guess either, and it's what's used in
both the x86 poly1305, blake2s, and nhpoly1305 code already (in the form
of PAGE_SIZE, which this commit corrects to be explicitly 4k for the
former two).
Ard did some back of the envelope calculations and found that
at 5 cycles/byte (overestimate) on a 1ghz processor (pretty slow), 4k
means we have a maximum preemption disabling of 20us, which Sebastian
confirmed was probably a good limit.
Unfortunately the chunking appears to have been left out of the final
patchset that added the glue code. So, this commit adds it back in.
Fixes: 84e03fa39fbe ("crypto: x86/chacha - expose SIMD ChaCha routine as library function")
Fixes: b3aad5bad26a ("crypto: arm64/chacha - expose arm64 ChaCha routine as library function")
Fixes: a44a3430d71b ("crypto: arm/chacha - expose ARM ChaCha routine as library function")
Fixes: d7d7b8535662 ("crypto: x86/poly1305 - wire up faster implementations for kernel")
Fixes: f569ca164751 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Fixes: a6b803b3ddc7 ("crypto: arm/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Fixes: ed0356eda153 ("crypto: blake2s - x86_64 SIMD implementation")
Cc: Eric Biggers <ebiggers@google.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull power management fixes from Rafael Wysocki:
- prevent the intel_pstate driver from printing excessive diagnostic
messages in some cases (Chris Wilson)
- make the hibernation restore kernel freeze kernel threads as well as
user space tasks (Dexuan Cui)
- fix the ACPI device PM disagnostic messages to include the correct
power state name (Kai-Heng Feng).
* tag 'pm-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: ACPI: Output correct message on target power state
PM: hibernate: Freeze kernel threads in software_resume()
cpufreq: intel_pstate: Only mention the BIOS disabling turbo mode once
The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.
Fixes: 0ae349a0f33f ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200418134703.1760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some older compilers like gcc-4.8 warn about mismatched curly braces in
a initializer:
fs/btrfs/backref.c: In function 'is_shared_data_backref':
fs/btrfs/backref.c:394:9: error: missing braces around
initializer [-Werror=missing-braces]
struct prelim_ref target = {0};
^
fs/btrfs/backref.c:394:9: error: (near initialization for
'target.rbnode') [-Werror=missing-braces]
Use the GNU empty initializer extension to avoid this.
Fixes: ed58f2e66e84 ("btrfs: backref, don't add refs from shared block when resolving normal backref")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The following execution path is possible:
fsnotify()
[ realign the stack and store previous SP in R10 ]
<IRQ>
[ only IRET regs saved ]
common_interrupt()
interrupt_entry()
<NMI>
[ full pt_regs saved ]
...
[ unwind stack ]
When the unwinder goes through the NMI and the IRQ on the stack, and
then sees fsnotify(), it doesn't have access to the value of R10,
because it only has the five IRET registers. So the unwind stops
prematurely.
However, because the interrupt_entry() code is careful not to clobber
R10 before saving the full regs, the unwinder should be able to read R10
from the previously saved full pt_regs associated with the NMI.
Handle this case properly. When encountering an IRET regs frame
immediately after a full pt_regs frame, use the pt_regs as a backup
which can be used to get the C register values.
Also, note that a call frame resets the 'prev_regs' value, because a
function is free to clobber the registers. For this fix to work, the
IRET and full regs frames must be adjacent, with no FUNC frames in
between. So replace the FUNC hint in interrupt_entry() with an
IRET_REGS hint.
Fixes: ee9f8fce9964 ("x86/unwind: Add the ORC unwinder")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Jones <dsj@fb.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lore.kernel.org/r/97a408167cc09f1cfa0de31a7b70dd88868d743f.1587808742.git.jpoimboe@redhat.com
gcc-10 has started warning about conflicting types for a few new
built-in functions, particularly 'free()'.
This results in warnings like:
crypto/xts.c:325:13: warning: conflicting types for built-in function ‘free’; expected ‘void(void *)’ [-Wbuiltin-declaration-mismatch]
because the crypto layer had its local freeing functions called
'free()'.
Gcc-10 is in the wrong here, since that function is marked 'static', and
thus there is no chance of confusion with any standard library function
namespace.
But the simplest thing to do is to just use a different name here, and
avoid this gcc mis-feature.
[ Side note: gcc knowing about 'free()' is in itself not the
mis-feature: the semantics of 'free()' are special enough that a
compiler can validly do special things when seeing it.
So the mis-feature here is that gcc thinks that 'free()' is some
restricted name, and you can't shadow it as a local static function.
Making the special 'free()' semantics be a function attribute rather
than tied to the name would be the much better model ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the unused functions set_kernel_text_rw/ro.
Currently, it is not being invoked from anywhere and no other architecture
(except arm) uses this code. Even in ARM, these functions are not invoked
from anywhere currently.
Fixes: d27c3c90817e ("riscv: add STRICT_KERNEL_RWX support")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cache a copy of the name for the life time of the backing_dev_info
structure so that we can reference it even after unregistering.
Fixes: 68f23b89067f ("memcg: fix a crash in wb_workfn when a device disappears")
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The update_domain() function is expected to also inform the hardware
about domain changes. This needs a COMPLETION_WAIT command to be sent
to all IOMMUs which use the domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-4-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull gcc-plugins fixes from Kees Cook:
"GCC 10 fixes for gcc-plugins:
- Adjust caller of cgraph_create_edge for GCC 10 argument usage
- Update common headers to build under GCC 10 (Frédéric Pierret)"
* tag 'gcc-plugins-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-common.h: Update for GCC 10
gcc-plugins/stackleak: Avoid assignment for unused macro argument
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the Dell K12A keyboard-dock,
which can be used with various Dell Venue 11 models.
Without this quirk the keyboard/touchpad combo works fine when connected
at boot, but when hotplugged 9 out of 10 times it will not work properly.
Adding the quirk fixes this.
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When both CONFIG_DEBUG_FS and CONFIG_PM_SLEEP are disabled, the
functions that got moved out of the #ifdef section now cause
a warning:
drivers/platform/x86/intel_pmc_core.c:654:13: error: 'pmc_core_lpm_display' defined but not used [-Werror=unused-function]
654 | static void pmc_core_lpm_display(struct pmc_dev *pmcdev, struct device *dev,
| ^~~~~~~~~~~~~~~~~~~~
drivers/platform/x86/intel_pmc_core.c:617:13: error: 'pmc_core_slps0_display' defined but not used [-Werror=unused-function]
617 | static void pmc_core_slps0_display(struct pmc_dev *pmcdev, struct device *dev,
| ^~~~~~~~~~~~~~~~~~~~~~
Rather than add even more #ifdefs here, remove them entirely and
let the compiler work it out, it can actually get rid of all the
debugfs calls without problems as long as the struct member is
there.
The two PM functions just need a __maybe_unused annotations to avoid
another warning instead of the #ifdef.
Fixes: aae43c2bcdc1 ("platform/x86: intel_pmc_core: Relocate pmc_core_*_display() to outside of CONFIG_DEBUG_FS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For skcipher algorithms, the input, output HW S/G tables
look like this: [IV, src][dst, IV]
Now, we can have 2 conditions here:
- there is no IV;
- src and dst are equal (in-place encryption) and scattered
and the error is an "off-by-one" in the HW S/G table.
This issue was seen with KASAN:
BUG: KASAN: slab-out-of-bounds in skcipher_edesc_alloc+0x95c/0x1018
Read of size 4 at addr ffff000022a02958 by task cryptomgr_test/321
CPU: 2 PID: 321 Comm: cryptomgr_test Not tainted
5.6.0-rc1-00165-ge4ef8383-dirty #4
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load4+0x90/0xb0
skcipher_edesc_alloc+0x95c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Allocated by task 321:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
skcipher_edesc_alloc+0x21c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff000022a02800
which belongs to the cache dma-kmalloc-512 of size 512
The buggy address is located 344 bytes inside of
512-byte region [ffff000022a02800, ffff000022a02a00)
The buggy address belongs to the page:
page:fffffe00006a8000 refcount:1 mapcount:0 mapping:ffff00093200c400
index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c400
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000022a02800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff000022a02880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff000022a02900: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
^
ffff000022a02980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff000022a02a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 334d37c9e263 ("crypto: caam - update IV using HW support")
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull iomap fix from Darrick Wong:
"Hoist the check for an unrepresentable FIBMAP return value into
ioctl_fibmap.
The internal kernel function can handle 64-bit values (and is needed
to fix a regression on ext4 + jbd2). It is only the userspace ioctl
that is so old that it cannot deal"
* tag 'iomap-5.7-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fibmap: Warn and return an error in case of block > INT_MAX
In commit a7ba5c3d008d ("drivers/iommu: Export core IOMMU API symbols to
permit modular drivers") a bunch of iommu symbols were exported, all
with _GPL markings except iommu_group_get_for_dev(). That export should
also be _GPL like the others.
Fixes: a7ba5c3d008d ("drivers/iommu: Export core IOMMU API symbols to permit modular drivers")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200430120120.2948448-1-gregkh@linuxfoundation.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
[BUG]
One run of btrfs/063 triggered the following lockdep warning:
============================================
WARNING: possible recursive locking detected
5.6.0-rc7-custom+ #48 Not tainted
--------------------------------------------
kworker/u24:0/7 is trying to acquire lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
but task is already holding lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sb_internal#2);
lock(sb_internal#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u24:0/7:
#0: ffff88817b495948 ((wq_completion)btrfs-endio-write){+.+.}, at: process_one_work+0x557/0xb80
#1: ffff888189ea7db8 ((work_completion)(&work->normal_work)){+.+.}, at: process_one_work+0x557/0xb80
#2: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
#3: ffff888174ca4da8 (&fs_info->reloc_mutex){+.+.}, at: btrfs_record_root_in_trans+0x83/0xd0 [btrfs]
stack backtrace:
CPU: 0 PID: 7 Comm: kworker/u24:0 Not tainted 5.6.0-rc7-custom+ #48
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
Call Trace:
dump_stack+0xc2/0x11a
__lock_acquire.cold+0xce/0x214
lock_acquire+0xe6/0x210
__sb_start_write+0x14e/0x290
start_transaction+0x66c/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
find_free_extent+0x1504/0x1a50 [btrfs]
btrfs_reserve_extent+0xd5/0x1f0 [btrfs]
btrfs_alloc_tree_block+0x1ac/0x570 [btrfs]
btrfs_copy_root+0x213/0x580 [btrfs]
create_reloc_root+0x3bd/0x470 [btrfs]
btrfs_init_reloc_root+0x2d2/0x310 [btrfs]
record_root_in_trans+0x191/0x1d0 [btrfs]
btrfs_record_root_in_trans+0x90/0xd0 [btrfs]
start_transaction+0x16e/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
btrfs_finish_ordered_io+0x55d/0xcd0 [btrfs]
finish_ordered_fn+0x15/0x20 [btrfs]
btrfs_work_helper+0x116/0x9a0 [btrfs]
process_one_work+0x632/0xb80
worker_thread+0x80/0x690
kthread+0x1a3/0x1f0
ret_from_fork+0x27/0x50
It's pretty hard to reproduce, only one hit so far.
[CAUSE]
This is because we're calling btrfs_join_transaction() without re-using
the current running one:
btrfs_finish_ordered_io()
|- btrfs_join_transaction() <<< Call #1
|- btrfs_record_root_in_trans()
|- btrfs_reserve_extent()
|- btrfs_join_transaction() <<< Call #2
Normally such btrfs_join_transaction() call should re-use the existing
one, without trying to re-start a transaction.
But the problem is, in btrfs_join_transaction() call #1, we call
btrfs_record_root_in_trans() before initializing current::journal_info.
And in btrfs_join_transaction() call #2, we're relying on
current::journal_info to avoid such deadlock.
[FIX]
Call btrfs_record_root_in_trans() after we have initialized
current::journal_info.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If the ORC entry type is unknown, nothing else can be done other than
reporting an error. Exit the function instead of breaking out of the
switch statement.
Fixes: ee9f8fce9964 ("x86/unwind: Add the ORC unwinder")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Jones <dsj@fb.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lore.kernel.org/r/a7fa668ca6eabbe81ab18b2424f15adbbfdc810a.1587808742.git.jpoimboe@redhat.com
gcc-10 now warns about passing aliasing pointers to functions that take
restricted pointers.
That's actually a great warning, and if we ever start using 'restrict'
in the kernel, it might be quite useful. But right now we don't, and it
turns out that the only thing this warns about is an idiom where we have
declared a few functions to be "printf-like" (which seems to make gcc
pick up the restricted pointer thing), and then we print to the same
buffer that we also use as an input.
And people do that as an odd concatenation pattern, with code like this:
#define sysfs_show_gen_prop(buffer, fmt, ...) \
snprintf(buffer, PAGE_SIZE, "%s"fmt, buffer, __VA_ARGS__)
where we have 'buffer' as both the destination of the final result, and
as the initial argument.
Yes, it's a bit questionable. And outside of the kernel, people do have
standard declarations like
int snprintf( char *restrict buffer, size_t bufsz,
const char *restrict format, ... );
where that output buffer is marked as a restrict pointer that cannot
alias with any other arguments.
But in the context of the kernel, that 'use snprintf() to concatenate to
the end result' does work, and the pattern shows up in multiple places.
And we have not marked our own version of snprintf() as taking restrict
pointers, so the warning is incorrect for now, and gcc picks it up on
its own.
If we do start using 'restrict' in the kernel (and it might be a good
idea if people find places where it matters), we'll need to figure out
how to avoid this issue for snprintf and friends. But in the meantime,
this warning is not useful.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put __cpu_up_stack_pointer and __cpu_up_task_pointer in data section.
Currently, these two variables are put in bss section, there is a
potential risk that secondary harts get the uninitialized value before
main hart finishing the bss clearing. In this case, all secondary
harts would pass the waiting loop and enable the MMU before main hart
set up the page table.
This issue happens on random booting of multiple harts, which means
it will manifest for BBL and OpenSBI v0.6 (or older version). In OpenSBI
v0.7 (or higher version), we have HSM extension so all the secondary harts
are brought-up by Linux kernel in an orderly fashion. This means we don't
need this change for OpenSBI v0.7 (or higher version).
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Use the common interface bdi_dev_name() to get device name.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Add missing <linux/backing-dev.h> include BFQ
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When increase_address_space() fails to allocate memory, alloc_pte()
will call it again until it succeeds. Do not loop forever while trying
to increase the address space and just return an error instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Remove "params.h" include, which has been dropped in GCC 10.
Remove is_a_helper() macro, which is now defined in gimple.h, as seen
when running './scripts/gcc-plugin.sh g++ g++ gcc':
In file included from <stdin>:1:
./gcc-plugins/gcc-common.h:852:13: error: redefinition of ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’
852 | inline bool is_a_helper<const ggoto *>::test(const_gimple gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from ./gcc-plugins/gcc-common.h:125,
from <stdin>:1:
/usr/lib/gcc/x86_64-redhat-linux/10/plugin/include/gimple.h:1037:1: note: ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’ previously declared here
1037 | is_a_helper <const ggoto *>::test (const gimple *gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Add -Wno-format-diag to scripts/gcc-plugins/Makefile to avoid
meaningless warnings from error() formats used by plugins:
scripts/gcc-plugins/structleak_plugin.c: In function ‘int plugin_init(plugin_name_args*, plugin_gcc_version*)’:
scripts/gcc-plugins/structleak_plugin.c:253:12: warning: unquoted sequence of 2 consecutive punctuation characters ‘'-’ in format [-Wformat-diag]
253 | error(G_("unknown option '-fplugin-arg-%s-%s'"), plugin_name, argv[i].key);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Frédéric Pierret (fepitre) <frederic.pierret@qubes-os.org>
Link: https://lore.kernel.org/r/20200407113259.270172-1-frederic.pierret@qubes-os.org
[kees: include -Wno-format-diag for plugin builds]
Signed-off-by: Kees Cook <keescook@chromium.org>
Without gpiolib, this driver fails to link:
arm-linux-gnueabi-ld: drivers/hid/hid-mcp2221.o: in function `mcp2221_probe':
hid-mcp2221.c:(.text+0x1b0): undefined reference to `devm_gpiochip_add_data'
arm-linux-gnueabi-ld: drivers/hid/hid-mcp2221.o: in function `mcp_gpio_get':
hid-mcp2221.c:(.text+0x30c): undefined reference to `gpiochip_get_data'
Fixes: 328de1c519c5 ("HID: mcp2221: add GPIO functionality support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
asus-nb-wmi does not add any extra functionality on these Asus
Transformer books. They have detachable keyboards, so the hotkeys are
send through a HID device (and handled by the hid-asus driver) and also
the rfkill functionality is not used on these devices.
Besides not adding any extra functionality, initializing the WMI interface
on these devices actually has a negative side-effect. For some reason
the \_SB.ATKD.INIT() function which asus_wmi_platform_init() calls drives
GPO2 (INT33FC:02) pin 8, which is connected to the front facing webcam LED,
high and there is no (WMI or other) interface to drive this low again
causing the LED to be permanently on, even during suspend.
This commit adds a blacklist of DMI system_ids on which not to load the
asus-nb-wmi and adds these Transformer books to this list. This fixes
the webcam LED being permanently on under Linux.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Here's the KASAN report:
BUG: KASAN: use-after-free in rsa_pub_done+0x70/0xe8
Read of size 1 at addr ffff000023082014 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #60
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
rsa_pub_done+0x70/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
cpuidle_enter_state+0xa4/0x490
cpuidle_enter+0x48/0x70
call_cpuidle+0x44/0x70
do_idle+0x304/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
rsa_edesc_alloc+0x2cc/0xe10
caam_rsa_enc+0x9c/0x5f0
test_akcipher_one+0x78c/0x968
alg_test_akcipher+0x78/0xf8
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
rsa_pub_done+0x68/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff000023082000
which belongs to the cache dma-kmalloc-256 of size 256
The buggy address is located 20 bytes inside of
256-byte region [ffff000023082000, ffff000023082100)
The buggy address belongs to the page:
page:fffffe00006c2080 refcount:1 mapcount:0 mapping:ffff00093200c200 index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c200
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000023081f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff000023081f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff000023082000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff000023082080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff000023082100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: bf53795025a2 ("crypto: caam - add crypto_engine support for RSA algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes:
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect
requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups:
- Remove unreachable error conditions"
* tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a race in __nfs_list_for_each_server()
NFSv4.1: fix handling of backchannel binding in BIND_CONN_TO_SESSION
SUNRPC: defer slow parts of rpc_free_client() to a workqueue.
NFSv4: Remove unreachable error condition due to rpc_run_task()
SUNRPC: Remove unreachable error condition
xprtrdma: Fix use of xdr_stream_encode_item_{present, absent}
xprtrdma: Fix trace point use-after-free race
xprtrdma: Restore wake-up-all to rpcrdma_cm_event_handler()
nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl
NFS/pnfs: Fix a credential use-after-free issue in pnfs_roc()
NFS/pnfs: Ensure that _pnfs_return_layout() waits for layoutreturn completion
We better warn the fibmap user and not return a truncated and therefore
an incorrect block map address if the bmap() returned block address
is greater than INT_MAX (since user supplied integer pointer).
It's better to pr_warn() all user of ioctl_fibmap() and return a proper
error code rather than silently letting a FS corruption happen if the
user tries to fiddle around with the returned block map address.
We fix this by returning an error code of -ERANGE and returning 0 as the
block mapping address in case if it is > INT_MAX.
Now iomap_bmap() could be called from either of these two paths.
Either when a user is calling an ioctl_fibmap() interface to get
the block mapping address or by some filesystem via use of bmap()
internal kernel API.
bmap() kernel API is well equipped with handling of u64 addresses.
WARN condition in iomap_bmap_actor() was mainly added to warn all
the fibmap users. But now that we have directly added this warning
for all fibmap users and also made sure to return 0 as block map address
in case if addr > INT_MAX.
So we can now remove this logic from iomap_bmap_actor().
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Transitioned power state logged at the end of setting ACPI power.
However, D3cold won't be in the message because state can only be
D3hot at most.
Use target_state to corretly report when power state is D3cold.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>