Pull thermal fixes from Eduardo Valentin:
"Specifics in this pull request:

- Fixes in mediatek and OF thermal drivers

- Fixes in power_allocator governor

- More fixes of unsigned to int type change in thermal_core.c.

These change have been CI tested using KernelCI bot. \o/"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: fix Mediatek thermal controller build
thermal: consistently use int for trip temp
thermal: fix mtk_thermal build dependency
thermal: minor mtk_thermal.c cleanups
thermal: power_allocator: req_range multiplication should be a 64 bit type
thermal: of: add __init attribute

Pull asm-generic update from Arnd Bergmann:
"Here is one patch to wire up the preadv/pwritev system calls in the
generic system call table, which is required for all architectures
that were merged in the last few years, including arm64.

Usually these get merged along with the syscall implementation or one
of the architecture trees, but this time that did not happen.

Andre and Christoph both sent a version of this patch, I picked the
one I got first"

* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
generic syscalls: wire up preadv2 and pwritev2 syscalls

At least with CONFIG_COMPILE_TEST, there's no reason to assume
that CONFIG_RESET_CONTROLLER is set, but the code for this
controller requires it since it calls device_reset().

Make CONFIG_MTK_THERMAL properly depend on CONFIG_RESET_CONTROLLER.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull x86 fixes from Ingo Molnar:
"Misc fixes: two EDAC driver fixes, a Xen crash fix, a HyperV log spam
fix and a documentation fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86 EDAC, sb_edac.c: Take account of channel hashing when needed
x86 EDAC, sb_edac.c: Repair damage introduced when "fixing" channel address
x86/mm/xen: Suppress hugetlbfs in PV guests
x86/doc: Correct limits in Documentation/x86/x86_64/mm.txt
x86/hyperv: Avoid reporting bogus NMI status for Gen2 instances

These new syscalls are implemented as generic code, so enable them for
architectures like arm64 which use the generic syscall table.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The commit 17e8351a7739 consistently use int for temperature,
however it missed a few in trip temperature and thermal_core.

In current codes, the trip->temperature used "unsigned long"
and zone->temperature used"int", if the temperature is negative
value, it will get wrong result when compare temperature with
trip temperature.

This patch can fix it.

Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull perf, cpu hotplug and timer fixes from Ingo Molnar:
"perf:
- A single tooling fix for a user-triggerable segfault.

CPU hotplug:
- Fix a CPU hotplug corner case regression, introduced by the recent
hotplug rework

timers:
- Fix a boot hang in the ARM based Tango SoC clocksource driver"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf intel-pt: Fix segfault tracing transactions

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Fix rollback during error-out in __cpu_disable()

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/tango-xtal: Fix boot hang due to incorrect test

Haswell and Broadwell can be configured to hash the channel
interleave function using bits [27:12] of the physical address.

On those processor models we must check to see if hashing is
enabled (bit21 of the HASWELL_HASYSDEFEATURE2 register) and
act accordingly.

Based on a patch by patrickg <patrickg@supermicro.com>

Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Fix build errors when MTK_THERMAL=y and NVMEM=m by preventing that
Kconfig combination.

drivers/built-in.o: In function `mtk_thermal_probe':
mtk_thermal.c:(.text+0xffa8f): undefined reference to `nvmem_cell_get'
mtk_thermal.c:(.text+0xffabe): undefined reference to `nvmem_cell_read'
mtk_thermal.c:(.text+0xffac9): undefined reference to `nvmem_cell_put'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: <linux-pm@vger.kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Hanyi Wu <hanyi.wu@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull locking fixes from Ingo Molnar:
"Misc fixes:

pvqspinlocks:
- an instrumentation fix

futexes:
- preempt-count vs pagefault_disable decouple corner case fix
- futex requeue plist race window fix
- futex UNLOCK_PI transaction fix for a corner case"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
asm-generic/futex: Re-enable preemption in futex_atomic_cmpxchg_inatomic()
futex: Acknowledge a new waiter in counter before plist
futex: Handle unlock_pi race gracefully
locking/pvqspinlock: Fix division by zero in qstat_read()

Pull a perf/urgent fix from Arnaldo Carvalho de Melo:

- Fix segfault tracing transactions in Intel PT (Adrian Hunter)

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The recent introduction of the hotplug thread which invokes the callbacks on
the plugged cpu, cased the following regression:

If takedown_cpu() fails, then we run into several issues:

1) The rollback of the target cpu states is not invoked. That leaves the smp
threads and the hotplug thread in disabled state.

2) notify_online() is executed due to a missing skip_onerr flag. That causes
that both CPU_DOWN_FAILED and CPU_ONLINE notifications are invoked which
confuses quite some notifiers.

3) The CPU_DOWN_FAILED notification is not invoked on the target CPU. That's
not an issue per se, but it is inconsistent and in consequence blocks the
patches which rely on these states being invoked on the target CPU and not
on the controlling cpu. It also does not preserve the strict call order on
rollback which is problematic for the ongoing state machine conversion as
well.

To fix this we add a rollback flag to the remote callback machinery and invoke
the rollback including the CPU_DOWN_FAILED notification on the remote
cpu. Further mark the notify online state with 'skip_onerr' so we don't get a
double invokation.

This workaround will go away once we moved the unplug invocation to the target
cpu itself.

[ tglx: Massaged changelog and moved the CPU_DOWN_FAILED notifiaction to the
target cpu ]

Fixes: 4cb28ced23c4 ("cpu/hotplug: Create hotplug threads")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-s390@vger.kernel.org
Cc: rt@linutronix.de
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: http://lkml.kernel.org/r/20160408124015.GA21960@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Commit 0881841f7e78 introduced a regression by inverting a test check
after calling clocksource_mmio_init(). That results on the system to
hang at boot time.

Fix it by inverting the test again.

Fixes: 0881841f7e78 ("Replace code by clocksource_mmio_init")
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

In commit:

eb1af3b71f9d ("Fix computation of channel address")

I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.

Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: eb1af3b71f9d ("Fix computation of channel address")
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull device mapper fix from Mike Snitzer:
"Fix for earlier 4.6-rc4 stable@ commit that introduced improper use of
write lock in cmd_read_lock() -- due to cut-n-paste gone awry (and
sparse didn't catch it)"

* tag 'dm-4.6-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache metadata: fix cmd_read_lock() acquiring write lock

Trivial cleanups:
- delete one duplicate #include
- end email address with closing '>'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Hanyi Wu <hanyi.wu@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull irq fixes from Ingo Molnar:
"A core irq affinity masks related fix and a MIPS irqchip driver fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips-gic: Don't overrun pcpu_masks array
genirq: Dont allow affinity mask to be updated on IPIs

The recent decoupling of pagefault disable and preempt disable added an
explicit preempt_disable/enable() pair to the futex_atomic_cmpxchg_inatomic()
implementation in asm-generic/futex.h. But it forgot to add preempt_enable()
calls to the error handling code pathes, which results in a preemption count
imbalance.

This is observable on boot when the test for atomic_cmpxchg() is calling
futex_atomic_cmpxchg_inatomic() on a NULL pointer.

Add the missing preempt_enable() calls to the error handling code pathes.

[ tglx: Massaged changelog ]

Fixes: d9b9ff8c1889 ("sched/preempt, futex: Disable preemption in UP futex_atomic_cmpxchg_inatomic() explicitly")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: linux-arch@vger.kernel.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1460640963-690-1-git-send-email-romain.perier@free-electrons.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Tracing a workload that uses transactions gave a seg fault as follows:

perf record -e intel_pt// workload
perf report
Program received signal SIGSEGV, Segmentation fault.
0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
at util/intel-pt.c:929
929 ptq->last_branch_rb->nr = 0;
(gdb) p ptq->last_branch_rb
$1 = (struct branch_stack *) 0x0
(gdb) up
1148 intel_pt_reset_last_branch_rb(ptq);
(gdb) l
1143 if (ret)
1144 pr_err("Intel Processor Trace: failed to deliver transaction event
1145 ret);
1146
1147 if (pt->synth_opts.callchain)
1148 intel_pt_reset_last_branch_rb(ptq);
1149
1150 return ret;
1151 }
1152
(gdb) p pt->synth_opts.callchain
$2 = true
(gdb)
(gdb) bt
#0 0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
#1 0x000000000054c1e0 in intel_pt_synth_transaction_sample (ptq=0x1a36110)
#2 0x000000000054c5b2 in intel_pt_sample (ptq=0x1a36110)

Caused by checking the 'callchain' flag when it should have been the
'last_branch' flag. Fix that.

Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: f14445ee72c5 ("perf intel-pt: Support generating branch stack")
Link: http://lkml.kernel.org/r/1460977068-11566-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Use signed integer output in the pr_err() string format, here PTR_ERR() value
is negative and it should be reported in human readable way.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1458603727-4446-1-git-send-email-vz@mleia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:

kernel BUG at .../fs/hugetlbfs/inode.c:428!
invalid opcode: 0000 [#1] SMP
...
RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320
...
Call Trace:
[<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40
[<ffffffff81167b3d>] evict+0xbd/0x1b0
[<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0
[<ffffffff81165b0e>] dput+0x1fe/0x220
[<ffffffff81150535>] __fput+0x155/0x200
[<ffffffff81079fc0>] task_work_run+0x60/0xa0
[<ffffffff81063510>] do_exit+0x160/0x400
[<ffffffff810637eb>] do_group_exit+0x3b/0xa0
[<ffffffff8106e8bd>] get_signal+0x1ed/0x470
[<ffffffff8100f854>] do_signal+0x14/0x110
[<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0
[<ffffffff814178a5>] retint_user+0x8/0x13

This is CVE-2016-3961 / XSA-174.

Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <JGross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: stable@vger.kernel.org
Cc: xen-devel <xen-devel@lists.xenproject.org>
Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes for 4.6-rc4. Full details
are in the shortlog, nothing major here.

These have all been in linux-next for a while with no reported issues"

* tag 'char-misc-4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: do not leak free page on kmalloc failure
lkdtm: fix memory leak of base
lkdtm: fix memory leak of val
extcon: palmas: Drop stray IRQF_EARLY_RESUME flag

Commit 9567366fefdd ("dm cache metadata: fix READ_LOCK macros and
cleanup WRITE_LOCK macros") uses down_write() instead of down_read() in
cmd_read_lock(), yet up_read() is used to release the lock in
READ_UNLOCK(). Fix it.

Fixes: 9567366fefdd ("dm cache metadata: fix READ_LOCK macros and cleanup WRITE_LOCK macros")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmed Samy <f.fallen45@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

req_range is declared as a u64 to cope with overflows in the
multiplication of two u32. As both req_power and power_range are u32,
we need to make sure the multiplication is done with u64 types.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull objtool fixes from Ingo Molnar:
"A handful of objtool fixes: two improvements to how warnings are
printed plus a false positive warning fix, and build environment fix"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix Makefile to properly see if libelf is supported
objtool: Detect falling through to the next function
objtool: Add workaround for GCC switch jump table bug

Commit 2a0787051182 ("irqchip/mips-gic: Use gic_vpes instead of
NR_CPUS") & commit 78930f09b940 ("irqchip/mips-gic: Clear percpu_masks
correctly when mapping") both introduce code which accesses gic_vpes
entries in the pcpu_masks array. However, this array has length NR_CPUS.
If NR_CPUS is less than gic_vpes (ie. the kernel supports use of less
CPUs than are present in the system) then we overrun the array, clobber
some other data & generally die pretty promptly.

Most notably this affects uniprocessor kernels running on any multicore
or multithreaded Malta with a GIC (ie. the vast majority of real Malta
boards).

Fix this by only accessing up to min(gic_vpes, NR_CPUS) entries in the
pcpu_masks array, preventing the array overrun.

Fixes: 2a0787051182 ("irqchip/mips-gic: Use gic_vpes instead of NR_CPUS")
Fixes: 78930f09b940 ("irqchip/mips-gic: Clear percpu_masks correctly when mapping")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1461234714-9975-1-git-send-email-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Otherwise an incoming waker on the dest hash bucket can miss
the waiter adding itself to the plist during the lockless
check optimization (small window but still the correct way
of doing this); similarly to the decrement counterpart.

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: bigeasy@linutronix.de
Cc: dvhart@infradead.org
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1461208164-29150-1-git-send-email-dave@stgolabs.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Patch 5a50f5291701 ("perf/x86/ibs: Fix race with IBS_STARTING state")
closed a big hole while opening another, smaller hole.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 5a50f5291701 ("perf/x86/ibs: Fix race with IBS_STARTING state")
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull cpu hotplug updates from Thomas Gleixner:
"This is the first part of the ongoing cpu hotplug rework:

- Initial implementation of the state machine

- Runs all online and prepare down callbacks on the plugged cpu and
not on some random processor

- Replaces busy loop waiting with completions

- Adds tracepoints so the states can be followed"

More detailed commentary on this work from an earlier email:
"What's wrong with the current cpu hotplug infrastructure?

- Asymmetry

The hotplug notifier mechanism is asymmetric versus the bringup and
teardown. This is mostly caused by the notifier mechanism.

- Largely undocumented dependencies

While some notifiers use explicitely defined notifier priorities,
we have quite some notifiers which use numerical priorities to
express dependencies without any documentation why.

- Control processor driven

Most of the bringup/teardown of a cpu is driven by a control
processor. While it is understandable, that preperatory steps,
like idle thread creation, memory allocation for and initialization
of essential facilities needs to be done before a cpu can boot,
there is no reason why everything else must run on a control
processor. Before this patch series, bringup looks like this:

Control CPU Booting CPU

do preparatory steps
kick cpu into life

do low level init

sync with booting cpu sync with control cpu

bring the rest up

- All or nothing approach

There is no way to do partial bringups. That's something which is
really desired because we waste e.g. at boot substantial amount of
time just busy waiting that the cpu comes to life. That's stupid
as we could very well do preparatory steps and the initial IPI for
other cpus and then go back and do the necessary low level
synchronization with the freshly booted cpu.

- Minimal debuggability

Due to the notifier based design, it's impossible to switch between
two stages of the bringup/teardown back and forth in order to test
the correctness. So in many hotplug notifiers the cancel
mechanisms are either not existant or completely untested.

- Notifier [un]registering is tedious

To [un]register notifiers we need to protect against hotplug at
every callsite. There is no mechanism that bringup/teardown
callbacks are issued on the online cpus, so every caller needs to
do it itself. That also includes error rollback.

What's the new design?

The base of the new design is a symmetric state machine, where both
the control processor and the booting/dying cpu execute a well
defined set of states. Each state is symmetric in the end, except
for some well defined exceptions, and the bringup/teardown can be
stopped and reversed at almost all states.

So the bringup of a cpu will look like this in the future:

Control CPU Booting CPU

do preparatory steps
kick cpu into life

do low level init

sync with booting cpu sync with control cpu

bring itself up

The synchronization step does not require the control cpu to wait.
That mechanism can be done asynchronously via a worker or some
other mechanism.

The teardown can be made very similar, so that the dying cpu cleans
up and brings itself down. Cleanups which need to be done after
the cpu is gone, can be scheduled asynchronously as well.

There is a long way to this, as we need to refactor the notion when a
cpu is available. Today we set the cpu online right after it comes
out of the low level bringup, which is not really correct.

The proper mechanism is to set it to available, i.e. cpu local
threads, like softirqd, hotplug thread etc. can be scheduled on that
cpu, and once it finished all booting steps, it's set to online, so
general workloads can be scheduled on it. The reverse happens on
teardown. First thing to do is to forbid scheduling of general
workloads, then teardown all the per cpu resources and finally shut it
off completely.

This patch series implements the basic infrastructure for this at the
core level. This includes the following:

- Basic state machine implementation with well defined states, so
ordering and prioritization can be expressed.

- Interfaces to [un]register state callbacks

This invokes the bringup/teardown callback on all online cpus with
the proper protection in place and [un]installs the callbacks in
the state machine array.

For callbacks which have no particular ordering requirement we have
a dynamic state space, so that drivers don't have to register an
explicit hotplug state.

If a callback fails, the code automatically does a rollback to the
previous state.

- Sysfs interface to drive the state machine to a particular step.

This is only partially functional today. Full functionality and
therefor testability will be achieved once we converted all
existing hotplug notifiers over to the new scheme.

- Run all CPU_ONLINE/DOWN_PREPARE notifiers on the booting/dying
processor:

Control CPU Booting CPU

do preparatory steps
kick cpu into life

do low level init

sync with booting cpu sync with control cpu
wait for boot
bring itself up

Signal completion to control cpu

In a previous step of this work we've done a full tree mechanical
conversion of all hotplug notifiers to the new scheme. The balance
is a net removal of about 4000 lines of code.

This is not included in this series, as we decided to take a
different approach. Instead of mechanically converting everything
over, we will do a proper overhaul of the usage sites one by one so
they nicely fit into the symmetric callback scheme.

I decided to do that after I looked at the ugliness of some of the
converted sites and figured out that their hotplug mechanism is
completely buggered anyway. So there is no point to do a
mechanical conversion first as we need to go through the usage
sites one by one again in order to achieve a full symmetric and
testable behaviour"

* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
cpu/hotplug: Document states better
cpu/hotplug: Fix smpboot thread ordering
cpu/hotplug: Remove redundant state check
cpu/hotplug: Plug death reporting race
rcu: Make CPU_DYING_IDLE an explicit call
cpu/hotplug: Make wait for dead cpu completion based
cpu/hotplug: Let upcoming cpu bring itself fully up
arch/hotplug: Call into idle with a proper state
cpu/hotplug: Move online calls to hotplugged cpu
cpu/hotplug: Create hotplug threads
cpu/hotplug: Split out the state walk into functions
cpu/hotplug: Unpark smpboot threads from the state machine
cpu/hotplug: Move scheduler cpu_online notifier to hotplug core
cpu/hotplug: Implement setup/removal interface
cpu/hotplug: Make target state writeable
cpu/hotplug: Add sysfs state interface
cpu/hotplug: Hand in target state to _cpu_up/down
cpu/hotplug: Convert the hotplugged cpu work to a state machine
cpu/hotplug: Convert to a state machine for the control processor
cpu/hotplug: Add tracepoints
...

Correct the size of the module mapping space and the maximum available
physical memory size of current processors.

Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1461310504-15977-1-git-send-email-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull misc fixes from Greg KH:
"Here are three small fixes for 4.6-rc4.

Two fix up some lz4 issues with big endian systems, and the remaining
one resolves a minor debugfs issue that was reported.

All have been in linux-next with no reported issues"

* tag 'driver-core-4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lib: lz4: cleanup unaligned access efficiency detection
lib: lz4: fixed zram with lz4 on big endian machines
debugfs: Make automount point inodes permanently empty

Kees briefly writes:

fixes some possible memory allocation leaks on error paths

The READ_LOCK macro was incorrectly returning -EINVAL if
dm_bm_is_read_only() was true -- it will always be true once the cache
metadata transitions to read-only by dm_cache_metadata_set_read_only().

Wrap READ_LOCK and WRITE_LOCK multi-statement macros in do {} while(0).
Also, all accesses of the 'cmd' argument passed to these related macros
are now encapsulated in parenthesis.

A follow-up patch can be developed to eliminate the use of macros in
favor of pure C code. Avoiding that now given that this needs to apply
to stable@.

Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d14fcf3dd79 ("dm cache: make sure every metadata function checks fail_io")
Cc: stable@vger.kernel.org

Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.

The result of objdump -x on the function before the change is as follows:

0000000000000086 l F .text.unlikely 0000000000000739 thermal_of_build_thermal_zone

And after the change it is as follows:

0000000000000000 l F .init.text 0000000000000734 thermal_of_build_thermal_zone

Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull USB / PHY driver fixes from Greg KH:
"Here are two small sets of patches, both from subsystem trees, USB
gadget and PHY drivers.

Full details are in the shortlog, and they have all been in linux-next
for a while (before I merged them to the USB tree)"

* tag 'usb-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_fs: Fix use-after-free
usb: dwc3: gadget: Fix suspend/resume during device mode
usb: dwc3: fix memory leak of dwc->regset
usb: dwc3: core: fix PHY handling during suspend
usb: dwc3: omap: fix up error path on probe()
usb: gadget: composite: Clear reserved fields of SSP Dev Cap
phy: rockchip-emmc: adapt binding to specifiy register offset and length
phy: rockchip-emmc: should be a child device of the GRF
phy: rockchip-dp: should be a child device of the GRF

When doing a make allmodconfig, I hit the following compile error:

In file included from builtin-check.c:32:0:
elf.h:22:18: fatal error: gelf.h: No such file or directory
compilation terminated.
...

Digging into it, it appears that the $(shell ..) command in the Makefile does
not give the proper result when it fails to find -lelf, and continues to
compile objtool.

Instead, use the "try-run" makefile macro to perform the test. This gives a
proper result for both cases.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Fixes: 442f04c34a1a4 ("objtool: Add tool to perform compile-time stack metadata validation")
Link: http://lkml.kernel.org/r/20160420153234.GA24032@home.goodmis.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The IPI domain re-purposes the IRQ affinity to signify the mask of CPUs
that this IPI will deliver to. This must not be modified before the IPI
is destroyed again, so set the IRQ_NO_BALANCING flag to prevent the
affinity being overwritten by setup_affinity().

Without this, if an IPI is reserved for a single target CPU, then
allocated using __setup_irq(), the affinity is overwritten with
cpu_online_mask. When ipi_destroy() is subsequently called on a
multi-cpu system, it will attempt to free cpumask_weight() IRQs
that were never allocated, and crash.

Fixes: d17bf24e6952 ("genirq: Add a new generic IPI reservation code to irq core")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Link: http://lkml.kernel.org/r/1461229712-13057-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0
transition in user space first then the user space value might not have the
waiters bit set. This opens the following race:

CPU0 CPU1
uval = get_user(futex)
lock(hb)
lock(hb)
futex |= FUTEX_WAITERS
....
unlock(hb)

cmpxchg(futex, uval, newval)

So the cmpxchg fails and returns -EINVAL to user space, which is wrong because
the futex value is valid.

To handle this (yes, yet another) corner case gracefully, check for a flag
change and retry.

[ tglx: Massaged changelog and slightly reworked implementation ]

Fixes: ccf9e6a80d9e ("futex: Make unlock_pi more robust")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

In the error path, event_file not being NULL is used to determine
whether the event itself still needs to be free'd, so fix it up to
avoid leaking.

Reported-by: Leon Yu <chianglungyu@gmail.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 130056275ade ("perf: Do not double free")
Link: http://lkml.kernel.org/r/87twk06yxp.fsf@ashishki-desk.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull irq updates from Thomas Gleixner:
"The 4.6 pile of irq updates contains:

- Support for IPI irqdomains to support proper integration of IPIs to
and from coprocessors. The first user of this new facility is
MIPS. The relevant MIPS patches come with the core to avoid merge
ordering issues and have been acked by Ralf.

- A new command line option to set the default interrupt affinity
mask at boot time.

- Support for some more new ARM and MIPS interrupt controllers:
tango, alpine-msix and bcm6345-l1

- Two small cleanups for x86/apic which we merged into irq/core to
avoid yet another branch in x86 with two tiny commits.

- The usual set of updates, cleanups in drivers/irqchip. Mostly in
the area of ARM-GIC, arada-37-xp and atmel chips. Nothing
outstanding here"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
irqchip/irq-alpine-msi: Release the correct domain on error
irqchip/mxs: Fix error check of of_io_request_and_map()
irqchip/sunxi-nmi: Fix error check of of_io_request_and_map()
genirq: Export IRQ functions for module use
irqchip/gic/realview: Support more RealView DCC variants
Documentation/bindings: Document the Alpine MSIX driver
irqchip: Add the Alpine MSIX interrupt controller
irqchip/gic-v3: Always return IRQ_SET_MASK_OK_DONE in gic_set_affinity
irqchip/gic-v3-its: Mark its_init() and its children as __init
irqchip/gic-v3: Remove gic_root_node variable from the ITS code
irqchip/gic-v3: ACPI: Add redistributor support via GICC structures
irqchip/gic-v3: Add ACPI support for GICv3/4 initialization
irqchip/gic-v3: Refactor gic_of_init() for GICv3 driver
x86/apic: Deinline _flat_send_IPI_mask, save ~150 bytes
x86/apic: Deinline __default_send_IPI_*, save ~200 bytes
dt-bindings: interrupt-controller: Add SoC-specific compatible string to Marvell ODMI
irqchip/mips-gic: Add new DT property to reserve IPIs
MIPS: Delete smp-gic.c
MIPS: Make smp CMP, CPS and MT use the new generic IPI functions
MIPS: Add generic SMP IPI support
...

Requested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Generation2 instances don't support reporting the NMI status on port 0x61,
read from there returns 'ff' and we end up reporting nonsensical PCI
error (as there is no PCI bus in these instances) on all NMIs:

NMI: PCI system error (SERR) for reason ff on CPU 0.
Dazed and confused, but trying to continue

Fix the issue by overriding x86_platform.get_nmi_reason. Use 'booted on
EFI' flag to detect Gen2 instances.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Cathy Avery <cavery@redhat.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devel@linuxdriverproject.org
Link: http://lkml.kernel.org/r/1460728232-31433-1-git-send-email-vkuznets@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull USB driver fixes from Greg KH:
"Here are some small USB fixes for 4.6-rc4.

Mostly xhci fixes for reported issues, a UAS bug that has hit a number
of people, including stable tree users, and a few other minor things.

All have been in linux-next for a while with no reported issues"

* tag 'usb-4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: hcd: out of bounds access in for_each_companion
USB: uas: Add a new NO_REPORT_LUNS quirk
USB: uas: Limit qdepth at the scsi-host level
doc: usb: Fix typo in gadget_multi documentation
usb: host: xhci-plat: Make enum xhci_plat_type start at a non zero value
xhci: fix 10 second timeout on removal of PCI hotpluggable xhci controllers
usb: xhci: fix wild pointers in xhci_mem_cleanup
usb: host: xhci-plat: fix cannot work if R-Car Gen2/3 run on above 4GB phys
usb: host: xhci: add a new quirk XHCI_NO_64BIT_SUPPORT
xhci: resume USB 3 roothub first
usb: xhci: applying XHCI_PME_STUCK_QUIRK to Intel BXT B0 host
cdc-acm: fix crash if flushed with nothing buffered

These identifiers are bogus. The interested architectures should define
HAVE_EFFICIENT_UNALIGNED_ACCESS whenever relevant to do so. If this
isn't true for some arch, it should be fixed in the arch definition.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Chanwoo writes:

Update extcon for v4.6-rc3

This patch fixes the following one issue:
- In extcon-palmas.c, the external abort happen when wake-up from suspend state
on BeagleBoard-X15 platform. So, drop the IRQF_EARLY_RESUME flag.

This frees the allocated page if there is a kmalloc failure.

Signed-off-by: Kees Cook <keescook@chromium.org>

Commit c80914e81ec5b08 ("dm: return error if bio_integrity_clone() fails
in clone_bio()") changed clone_bio() such that if it does return error
then the alloc_tio() created resources (both the bio that was allocated
to be a clone and the containing dm_target_io struct) will leak.

Fix this by calling free_tio() in __clone_and_map_data_bio()'s
clone_bio() error path.

Fixes: c80914e81ec5b08 ("dm: return error if bio_integrity_clone() fails in clone_bio()")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Pull crypto fixes from Herbert Xu:
"This fixes the following issues:

- Incorrect output buffer size calculation in rsa-pkcs1pad

- Uninitialised padding bytes on exported state in ccp driver

- Potentially freed pointer used on completion callback in sha1-mb"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Prevent information leakage on export
crypto: sha1-mb - use corrcet pointer while completing jobs
crypto: rsa-pkcs1pad - fix dst len

Pull serial fixes from Greg KH:
"Here are 3 serial driver fixes for issues that have been reported.

Two are reverts, fixing problems that were in the big TTY/Serial
driver merge in 4.6-rc1, and the last one is a simple bugfix for a
regression that showed up in 4.6-rc1 as well.

All have been in linux-next with no reported issues"

* tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Add hardware dependency to RT288X option"
tty/serial/8250: fix RS485 half-duplex RX
Revert "serial-uartlite: Constify uartlite_be/uartlite_le"

Kishon writes:

phy: for 4.6-rc

*) make rockchip-dp and rockchip-emmc PHY child device of
GRF

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

There are several cases in compiled C code where a function may not
return at the end, and may instead fall through to the next function.

That may indicate a bug in the code, or a gcc bug, or even an objtool
bug. But in each case, objtool reports an unhelpful warning, something
like:

drivers/scsi/qla2xxx/qla_attr.o: warning: objtool: qla2x00_get_fc_host_stats()+0x0: duplicate frame pointer save
drivers/scsi/qla2xxx/qla_attr.o: warning: objtool: qla2x00_get_fc_host_stats()+0x0: frame pointer state mismatch

Detect this situation and print a more useful error message:

drivers/scsi/qla2xxx/qla_attr.o: warning: objtool: qla2x00_get_host_fabric_name() falls through to next function qla2x00_get_starget_node_name()

Also add some information about this warning and its potential causes to
the documentation.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/caa4ec6c687931db805e692d4e4bf06cd87d33e6.1460729697.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

While playing with the qstat statistics (in <debugfs>/qlockstat/) I ran into
the following splat on a VM when opening pv_hash_hops:

divide error: 0000 [#1] SMP
...
RIP: 0010:[<ffffffff810b61fe>] [<ffffffff810b61fe>] qstat_read+0x12e/0x1e0
...
Call Trace:
[<ffffffff811cad7c>] ? mem_cgroup_commit_charge+0x6c/0xd0
[<ffffffff8119750c>] ? page_add_new_anon_rmap+0x8c/0xd0
[<ffffffff8118d3b9>] ? handle_mm_fault+0x1439/0x1b40
[<ffffffff811937a9>] ? do_mmap+0x449/0x550
[<ffffffff811d3de3>] ? __vfs_read+0x23/0xd0
[<ffffffff811d4ab2>] ? rw_verify_area+0x52/0xd0
[<ffffffff811d4bb1>] ? vfs_read+0x81/0x120
[<ffffffff811d5f12>] ? SyS_read+0x42/0xa0
[<ffffffff815720f6>] ? entry_SYSCALL_64_fastpath+0x1e/0xa8

Fix this by verifying that qstat_pv_kick_unlock is in fact non-zero,
similarly to what the qstat_pv_latency_wake case does, as if nothing
else, this can come from resetting the statistics, thus having 0 kicks
should be quite valid in this context.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reviewed-by: Waiman Long <Waiman.Long@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: waiman.long@hpe.com
Link: http://lkml.kernel.org/r/1460961103-24953-1-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Stephane reported that commit:

3cbaa5906967 ("perf: Fix ctx time tracking by introducing EVENT_TIME")

introduced a regression wrt. time tracking, as easily observed by:

> This patch introduce a bug in the time tracking of events when
> multiplexing is used.
>
> The issue is easily reproducible with the following perf run:
>
> $ perf stat -a -C 0 -e branches,branches,branches,branches,branches,branches -I 1000
> 1.000730239 652,394 branches (66.41%)
> 1.000730239 597,809 branches (66.41%)
> 1.000730239 593,870 branches (66.63%)
> 1.000730239 651,440 branches (67.03%)
> 1.000730239 656,725 branches (66.96%)
> 1.000730239 <not counted> branches
>
> One branches event is shown as not having run. Yet, with
> multiplexing, all events should run especially with a 1s (-I 1000)
> interval. The delta for time_running comes out to 0. Yet, the event
> has run because the kernel is actually multiplexing the events. The
> problem is that the time tracking is the kernel and especially in
> ctx_sched_out() is wrong now.
>
> The problem is that in case that the kernel enters ctx_sched_out() with the
> following state:
> ctx->is_active=0x7 event_type=0x1
> Call Trace:
> [<ffffffff813ddd41>] dump_stack+0x63/0x82
> [<ffffffff81182bdc>] ctx_sched_out+0x2bc/0x2d0
> [<ffffffff81183896>] perf_mux_hrtimer_handler+0xf6/0x2c0
> [<ffffffff811837a0>] ? __perf_install_in_context+0x130/0x130
> [<ffffffff810f5818>] __hrtimer_run_queues+0xf8/0x2f0
> [<ffffffff810f6097>] hrtimer_interrupt+0xb7/0x1d0
> [<ffffffff810509a8>] local_apic_timer_interrupt+0x38/0x60
> [<ffffffff8175ca9d>] smp_apic_timer_interrupt+0x3d/0x50
> [<ffffffff8175ac7c>] apic_timer_interrupt+0x8c/0xa0
>
> In that case, the test:
> if (is_active & EVENT_TIME)
>
> will be false and the time will not be updated. Time must always be updated on
> sched out.

Fix this by always updating time if EVENT_TIME was set, as opposed to
only updating time when EVENT_TIME changed.

Reported-by: Stephane Eranian <eranian@google.com>
Tested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Fixes: 3cbaa5906967 ("perf: Fix ctx time tracking by introducing EVENT_TIME")
Link: http://lkml.kernel.org/r/20160329072644.GB3408@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull timer updates from Thomas Gleixner:
"The timer department delivers this time:

- Support for cross clock domain timestamps in the core code plus a
first user. That allows more precise timestamping for PTP and
later for audio and other peripherals.

The ptp/e1000e patches have been acked by the relevant maintainers
and are carried in the timer tree to avoid merge ordering issues.

- Support for unregistering the current clocksource watchdog. That
lifts a limitation for switching clocksources which has been there
from day 1

- The usual pile of fixes and updates to the core and the drivers.
Nothing outstanding and exciting"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
time/timekeeping: Work around false positive GCC warning
e1000e: Adds hardware supported cross timestamp on e1000e nic
ptp: Add PTP_SYS_OFFSET_PRECISE for driver crosstimestamping
x86/tsc: Always Running Timer (ART) correlated clocksource
hrtimer: Revert CLOCK_MONOTONIC_RAW support
time: Add history to cross timestamp interface supporting slower devices
time: Add driver cross timestamp interface for higher precision time synchronization
time: Remove duplicated code in ktime_get_raw_and_real()
time: Add timekeeping snapshot code capturing system time and counter
time: Add cycles to nanoseconds translation
jiffies: Use CLOCKSOURCE_MASK instead of constant
clocksource: Introduce clocksource_freq2mult()
clockevents/drivers/exynos_mct: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_global_timer: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_arch_timer: Implement ->set_state_oneshot_stopped()
clocksource/drivers/arm_global_timer: Register delay timer
clocksource/drivers/lpc32xx: Support timer-based ARM delay
clocksource/drivers/lpc32xx: Support periodic mode
clocksource/drivers/lpc32xx: Don't use the prescaler counter for clockevents
clocksource/drivers/rockchip: Add err handle for rk_timer_init
...

Pull irqchip core changes from Jason Cooper:

- mvebu: Update dt binding docs for new odmi driver

Commit 931ef163309e moved the smpboot thread park/unpark invocation to the
state machine. The move of the unpark invocation was premature as it depends
on work in progress patches.

As a result cpu down can fail, because rcu synchronization in takedown_cpu()
eventually requires a functional softirq thread. I never encountered the
problem in testing, but 0day testing managed to provide a reliable reproducer.

Remove the smpboot_threads_park() call from the state machine for now and put
it back into the original place after the rcu synchronization.

I'm embarrassed as I knew about the dependency and still managed to get it
wrong. Hotplug induced brain melt seems to be the only sensible explanation
for that.

Fixes: 931ef163309e "cpu/hotplug: Unpark smpboot threads from the state machine"
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

Pull block fixes from Jens Axboe:
"A few fixes for the current series. This contains:

- Two fixes for NVMe:

One fixes a reset race that can be triggered by repeated
insert/removal of the module.

The other fixes an issue on some platforms, where we get probe
timeouts since legacy interrupts isn't working. This used not to
be a problem since we had the worker thread poll for completions,
but since that was killed off, it means those poor souls can't
successfully probe their NVMe device. Use a proper IRQ check and
probe (msi-x -> msi ->legacy), like most other drivers to work
around this. Both from Keith.

- A loop corruption issue with offset in iters, from Ming Lei.

- A fix for not having the partition stat per cpu ref count
initialized before sending out the KOBJ_ADD, which could cause user
space to access the counter prior to initialization. Also from
Ming Lei.

- A fix for using the wrong congestion state, from Kaixu Xia"

* 'for-linus' of git://git.kernel.dk/linux-block:
block: loop: fix filesystem corruption in case of aio/dio
NVMe: Always use MSI/MSI-x interrupts
NVMe: Fix reset/remove race
writeback: fix the wrong congested state variable definition
block: partition: initialize percpuref before sending out KOBJ_ADD