tjh.dev
commits
Pull SCSI fix from James Bottomley:
"A single fix for machines with pages > 4k (PPC mostly).
There's a bug in our optimal transfer size code where we don't account
for pages > 4k and can set the transfer size to be less than the page
size causing nasty failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Reject optimal transfer length smaller than page size
Pull PCI fixlet from Bjorn Helgaas:
"This marks the TI DRA7xx host bridge driver as broken. Apparently it
has never worked without some additional out-of-tree code, so I'm
going to mark it broken now and remove it completely next cycle unless
it's fixed"
* tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dra7xx: Mark driver as broken
kernel test robot has reported the following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000100
IP: [<c1074df6>] __queue_work+0x26/0x390
*pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53
Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe #1
Workqueue: events vmstat_shepherd
task: cb684600 ti: cb7ba000 task.ti: cb7ba000
EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0
EIP is at __queue_work+0x26/0x390
EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0
Stack:
Call Trace:
__queue_delayed_work+0xa1/0x160
queue_delayed_work_on+0x36/0x60
vmstat_shepherd+0xad/0xf0
process_one_work+0x1aa/0x4c0
worker_thread+0x41/0x440
kthread+0xb0/0xd0
ret_from_kernel_thread+0x21/0x40
The reason is that start_shepherd_timer schedules the shepherd work item
which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates
that workqueue so if the further initialization takes more than HZ we
might end up scheduling on a NULL vmstat_wq. This is really unlikely
but not impossible.
Fixes: 373ccbe59270 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark the dra7xx PCI host driver as broken. This driver was first merged in
v3.17 and has never worked. Although the driver compiles just fine, it is
missing an essential device reset. If the driver is included, the kernel
locks up hard shortly after booting, before any console output appears.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Eryu Guan reported that loading scsi_debug would fail. This turned out
to be caused by scsi_debug reporting an optimal I/O size of 32KB which
is smaller than the 64KB page size on the PowerPC system in question.
Add a check to ensure that we only use the device-reported OPTIMAL
TRANSFER LENGTH if it is bigger than or equal to the page cache size.
Reported-by: Eryu Guan <guaneryu@gmail.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull ARM SoC fixes from Arnd Bergmann:
"This is the final small set of ARM SoC bug fixes for linux-4.4, almost
all regressions:
OMAP:
- data corruption on the Nokia N900 flash
Allwinner:
- Two defconfig change to get USB working again
ARM Versatile:
- Interrupt numbers gone bad after an older bug fix
Nomadik:
- Crashes from incorrect L2 cache settings
VIA vt8500:
- SD/MMC support on WM8650 never worked"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dts: vt8500: Add SDHC node to DTS file for WM8650
ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices
ARM: versatile: fix MMC/SD interrupt assignment
ARM: nomadik: set latencies to 8 cycles
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
ARM: Fix broken USB support in sunxi_defconfig
For 32-bit config reads (size == 4), hisi_pcie_cfg_read() returned success
but never filled in the data we read.
Return the register data for 32-bit config reads.
Without this fix, PCI doesn't work at all because enumeration depends on
32-bit config reads. The driver was tested internally, but got broken in
the process of upstreaming, so this fixes the breakage.
Fixes: 500a1d9a43e0 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit 49718f0fb8c9 ("SCSI: Fix NULL pointer dereference in
runtime PM")
The old commit may lead to a issue that blk_{pre|post}_runtime_suspend and
blk_{pre|post}_runtime_resume may not be called in pairs.
Take sr device as example, when sr device goes to runtime suspend,
blk_{pre|post}_runtime_suspend will be called since sr device defined
pm->runtime_suspend. But blk_{pre|post}_runtime_resume will not be called
since sr device doesn't have pm->runtime_resume. so, sr device can not
resume correctly anymore.
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull KVM fix from Paolo Bonzini:
"A simple fix. I'm sending it before the merge window, because it
refines a patch found in your master branch but not yet in the
kvm/next branch that is destined for 4.5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: only channel 0 of the i8254 is linked to the HPET
Pull "urgent onenand file system corruption fix for n900" from Tony Lindgren:
Last minute urgent pull request to prevent file system corruption
on Nokia N900.
Looks like we have a GPMC bus timing bug that has gone unnoticed
because of bootloader configured registers until few days ago. We
are not detecting the onenand clock rate properly unless we have
CONFIG_OMAP_GPMC_DEBUG set and this causes onenand corruption
that can be easily be reproduced.
There seems to be also an additional bug still lurking around for
onenand corruption. But that is still being investigated and
it does not seem to be GPMC timings related.
Meanwhile, it would be good to get this fix into v4.4 to prevent
wrong timings from corrupting onenand.
* tag 'omap-for-v4.4/onenand-corruption' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
PCI interrupt lines start at 1, not at 0. So, creates additional one
interrupt when register for irq domain.
Error when PCIe devices have 4 INTx:
WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:280
irq_domain_associate+0x17c/0x1cc()
error: hwirq 0x4 is too large for dummy
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pull ACPI fix from Rafael Wysocki:
"Just one obvious fix that adds a missing function argument in ACPI
code introduced recently (Kees Cook)"
* tag 'pm+acpi-4.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / property: avoid leaking format string into kobject name
While setting the KVM PIT counters in 'kvm_pit_load_count', if
'hpet_legacy_start' is set, the function disables the timer on
channel[0], instead of the respective index 'channel'. This is
because channels 1-3 are not linked to the HPET. Fix the caller
to only activate the special HPET processing for channel 0.
Reported-by: P J P <pjp@fedoraproject.org>
Fixes: 0185604c2d82c560dab2f2933a18f797e74ab5a8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Reviewed-by: Alexey Charkov <alchark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
unified the GPMC debug for the SoCs with GPMC. The commit also left out
the option for HWMOD_INIT_NO_RESET as we now require proper timings for
GPMC to be able to remap GPMC devices out of address 0.
Unfortunately on Nokia N900, onenand now only partially works with the
device tree provided timings. It works enough to get detected but the
clock rate supported by the onenand chip gets misdetected. This in turn
causes the GPMC timings to be miscalculated and this leads into file
system corruption on N900.
Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync
write. This is needed also for async timings when we write to onenand
with omap2_onenand_set_async_mode(). Without sync write bit set, the
async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff.
Let's exit with an error if onenand rate is not detected. And let's
remove the extra call to omap2_onenand_set_async_mode() as we only need
to do this once at the end of omap2_onenand_setup_async().
Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Check TLP packet successful completion status. This fix the issue when
accessing multi-function devices in enumeration process, TLP will return
error when accessing non-exist function number. Returns PCI error code
instead of generic errno.
Tested on Ethernet adapter card with multi-functions.
[bhelgaas: simplify completion status checking code]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"A handful of x86 fixes:
- a syscall ABI fix, fixing an Android breakage
- a Xen PV guest fix relating to the RTC device, causing a
non-working console
- a Xen guest syscall stack frame fix
- an MCE hotplug CPU crash fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/numachip: Fix NumaConnect2 MMCFG PCI access
x86/entry: Restore traditional SYSENTER calling convention
x86/entry: Fix some comments
x86/paravirt: Prevent rtc_cmos platform device init on PV guests
x86/xen: Avoid fast syscall path for Xen PV guests
x86/mce: Ensure offline CPUs don't participate in rendezvous process
The dn->name is expected to be used as a literal, so add the missing
"%s".
Fixes: 263b4c1a64bc (ACPI / property: Expose data-only subnodes via sysfs)
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 69fb4dcada77 ("power: Add an axp20x-usb-power driver") introduced a
new driver for the USB power supply used on various Allwinner based SBCs.
However, the driver was not added to multi_v7_defconfig which breaks USB
support for some boards (e.g. LeMaker BananaPi) as the kernel will now
turn off the USB power supply during boot by default if the driver isn't
present. (This was not the case in linux 4.3 or lower where the USB power
was always left on.)
Hence, add the driver to multi_v7_defconfig in order to keep USB support
working on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Requester ID should use the Root Port devfn and it should be always 0.
Previously we constructed the Requester ID using the *Completer* devfn,
i.e., the devfn of the Function we expect to respond to the config access.
This causes issues when accessing configuration space for devices other
than the Root Port.
Build the Requester ID using the Root Port devfn.
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
Pull scheduler fixes from Ingo Molnar:
"Misc scheduler fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Reset task's lockless wake-queues on fork()
sched/core: Fix unserialized r-m-w scribbling stuff
sched/core: Check tgid in is_global_init()
sched/fair: Fix multiplication overflow on 32-bit systems
The MMCFG PCI accessors weren't being setup for NumacConnect2
correctly due to over-early assignment; this would create the
potential for the wrong PCI domain to be accessed.
Fix this by using the correct arch-specific PCI init function.
Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Acked-by: Steffen Persvold <sp@numascale.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1451498807-15920-1-git-send-email-daniel@numascale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull MIPS build fix from Ralf Baechle:
"Fix a makefile issue resulting in build breakage with older binutils.
This has sat in -next for a few days, testers and buildbot are happy
with it, too though if you are going for another -rc that'd certainly
help ironing out a few more issues"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: VDSO: Fix build error with binutils 2.24 and earlier
Commit 0976c946a610d06e907335b7a3afa6db046f8e1b
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.
However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.
Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.
For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.
Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.
Cc: Rob Herring <robh@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 0976c946a610 ("arm/versatile: Fix versatile irq specifications")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TLP_LOOP is 500 and the "loop" variable was a u8 so "loop < TLP_LOOP" is
always true. We only need this condition to work if there is a problem so
it would have been easy to miss this in testing.
Make it a normal for loop with "int i" instead of over thinking things and
making it complicated.
Fixes: 6bb4dd154ae8 ("PCI: altera: Add Altera PCIe host controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong. The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.
Cc: stable@vger.kernel.org # v4.2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull perf fixes from Ingo Molnar:
"Two core subsystem fixes, plus a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix race in swevent hash
perf: Fix race in perf_event_exec()
perf list: Robustify event printing routine
perf list: Add support for PERF_COUNT_SW_BPF_OUT
perf hists browser: Fix segfault if use symbol filter in cmdline
perf hists browser: Reset selection when refresh
perf hists browser: Add NULL pointer check to prevent crash
perf buildid-list: Fix return value of perf buildid-list -k
perf buildid-list: Show running kernel build id fix
In the following commit:
7675104990ed ("sched: Implement lockless wake-queues")
we gained lockless wake-queues.
The -RT kernel managed to lockup itself with those. There could be multiple
attempts for task X to enqueue it for a wakeup _even_ if task X is already
running.
The reason is that task X could be runnable but not yet on CPU. The the
task performing the wakeup did not leave the CPU it could performe
multiple wakeups.
With the proper timming task X could be running and enqueued for a
wakeup. If this happens while X is performing a fork() then its its
child will have a !NULL `wake_q` member copied.
This is not a problem as long as the child task does not participate in
lockless wakeups :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 7675104990ed ("sched: Implement lockless wake-queues")
Link: http://lkml.kernel.org/r/20151221171710.GA5499@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It turns out that some Android versions hardcode the SYSENTER
calling convention. This is buggy and will cause problems no
matter what the kernel does. Nonetheless, we should try to
support it.
Credit goes to Linus for pointing out a clean way to handle
the SYSENTER/SYSCALL clobber differences while preserving
straightforward DWARF annotations.
I believe that the original offending Android commit was:
https://android.googlesource.com/platform%2Fbionic/+/7dc3684d7a2587e43e6d2a8e0e3f39bf759bd535
Reported-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: <mark.gross@intel.com>
Cc: Su Tao <tao.su@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: <frank.wang@intel.com>
Cc: <borun.fu@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Mingwei Shi <mingwei.shi@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull i915 drm fixes from Jani Nikula:
"Two display fixes still for v4.4.
The new year's resolution is to start using signed tags per Linus'
request. This one is still unsigned; I want to fix this up in our
maintainer scripts instead of doing it one-off"
* tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: increase the tries for HDMI hotplug live status checking
drm/i915: Unbreak check_digital_port_conflicts()
Commit 2a037f310bab ("MIPS: VDSO: Fix build error") tries to fix a build
error seen with binutils 2.24 and earlier. However, the fix does not work,
and again results in the already known build errors if the kernel is built
with an earlier version of binutils.
CC arch/mips/vdso/gettimeofday.o
/tmp/ccnOVbHT.s: Assembler messages:
/tmp/ccnOVbHT.s:50: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
/tmp/ccnOVbHT.s:374: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
scripts/Makefile.build:258: recipe for target 'arch/mips/vdso/gettimeofday.o' failed
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
Fixes: 2a037f310bab ("MIPS: VDSO: Fix build error")
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11926/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.
These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct
device::msi_domain"), we use the MSI domain associated with the PCI device.
But finding an MSI domain doesn't mean that the domain is implemented using
the generic MSI domain API, and a number of MSI controllers are still using
arch_setup_msi_irq() and arch_teardown_msi_irqs().
Check that the domain we just obtained is hierarchical. If it is, we can
use the new generic MSI stuff. Otherwise we have to fall back to the old
arch_setup_msi_irq() and arch_teardown_msi_irqs() interfaces.
This avoids an oops in msi_domain_alloc_irqs() on systems with R-Car,
Tegra, Armada 370, and probably other DesignWare-based host controllers.
Fixes: d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct device::msi_domain")
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Tested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
CC: stable@vger.kernel.org # v4.3+
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
CPU0 CPU1
set_current_state(...)
<preempt_schedule>
context_switch(X, Y)
prepare_lock_switch(Y)
Y->on_cpu = 1;
finish_lock_switch(X)
store_release(X->on_cpu, 0);
try_to_wake_up(X)
LOCK(p->pi_lock);
t = X->on_cpu; // 0
context_switch(Y, X)
prepare_lock_switch(X)
X->on_cpu = 1;
finish_lock_switch(Y)
store_release(Y->on_cpu, 0);
</preempt_schedule>
schedule();
deactivate_task(X);
X->on_rq = 0;
if (X->on_rq) // false
if (t) while (X->on_cpu)
cpu_relax();
context_switch(X, ..)
finish_lock_switch(X)
store_release(X->on_cpu, 0);
Avoid the load of X->on_cpu being hoisted over the X->on_rq load.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull irq fix from Ingo Molnar:
"Fixes a core IRQ subsystem deadlock"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent chip buslock deadlock
There's a race on CPU unplug where we free the swevent hash array
while it can still have events on. This will result in a
use-after-free which is BAD.
Simply do not free the hash array on unplug. This leaves the thing
around and no use-after-free takes place.
When the last swevent dies, we do a for_each_possible_cpu() iteration
anyway to clean these up, at which time we'll free it, so no leakage
will occur.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the sched bitfieds (notably sched_reset_on_fork) can be set
on other than current, this can cause the r-m-w to race with other
updates.
Since all the sched bits are serialized by scheduler locks, pull them
in a separate word.
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: hannes@cmpxchg.org
Cc: mhocko@kernel.org
Cc: vdavydov@parallels.com
Link: http://lkml.kernel.org/r/20151125150207.GM11639@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: <mark.gross@intel.com>
Cc: Su Tao <tao.su@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: <qiuxu.zhuo@intel.com>
Cc: <frank.wang@intel.com>
Cc: <borun.fu@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Mingwei Shi <mingwei.shi@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull PCI bugfix from Bjorn Helgaas:
"Here's another fix for v4.4.
This fixes 32-bit config reads for the HiSilicon driver. Obviously
the driver is completely broken without this fix (apparently it
actually was tested internally, but got broken somehow in the process
of upstreaming it).
Summary:
HiSilicon host bridge driver
Fix 32-bit config reads (Dongdong Liu)"
* tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads
The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.
After doing experiments for following monitors, it needs 80ms at least
for those worst cases.
Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)
It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.com
Tested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c693d ("drm/i915: Check live status before reading edid")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea0053b23de42c828d559016eabe0b91523)
[Jani: undo the file mode change of the original commit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 69fb4dcada77 ("power: Add an axp20x-usb-power driver") introduced a new
driver for the USB power supply used on various Allwinner based SBCs. However,
the driver was not added to sunxi_defconfig which breaks USB support for some
boards (e.g. LeMaker BananaPi) as the kernel will now turn off the USB power
supply during boot by default if the driver isn't present. (This was not the
case in linux 4.3 or lower where the USB power was always left on.)
Hence, add the driver to sunxi_defconfig in order to keep USB support working
on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Reported-by: David Tulloh <david@tulloh.id.au>
Tested-by: David Tulloh <david@tulloh.id.au>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b3a72384fe29 ("ARM/PCI: Replace pci_sys_data->align_resource with
global function pointer") introduced an ARM-specific align_resource()
function pointer. This is not portable to other arches and doesn't work
for platforms with two different PCIe host bridge controllers.
Move the function pointer to the pci_host_bridge structure so each host
bridge driver can specify its own align_resource() function.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
Pull SCSI fix from James Bottomley:
"A single fix for machines with pages > 4k (PPC mostly).
There's a bug in our optimal transfer size code where we don't account
for pages > 4k and can set the transfer size to be less than the page
size causing nasty failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Reject optimal transfer length smaller than page size
Pull PCI fixlet from Bjorn Helgaas:
"This marks the TI DRA7xx host bridge driver as broken. Apparently it
has never worked without some additional out-of-tree code, so I'm
going to mark it broken now and remove it completely next cycle unless
it's fixed"
* tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dra7xx: Mark driver as broken
kernel test robot has reported the following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000100
IP: [<c1074df6>] __queue_work+0x26/0x390
*pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53
Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe #1
Workqueue: events vmstat_shepherd
task: cb684600 ti: cb7ba000 task.ti: cb7ba000
EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0
EIP is at __queue_work+0x26/0x390
EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0
Stack:
Call Trace:
__queue_delayed_work+0xa1/0x160
queue_delayed_work_on+0x36/0x60
vmstat_shepherd+0xad/0xf0
process_one_work+0x1aa/0x4c0
worker_thread+0x41/0x440
kthread+0xb0/0xd0
ret_from_kernel_thread+0x21/0x40
The reason is that start_shepherd_timer schedules the shepherd work item
which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates
that workqueue so if the further initialization takes more than HZ we
might end up scheduling on a NULL vmstat_wq. This is really unlikely
but not impossible.
Fixes: 373ccbe59270 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark the dra7xx PCI host driver as broken. This driver was first merged in
v3.17 and has never worked. Although the driver compiles just fine, it is
missing an essential device reset. If the driver is included, the kernel
locks up hard shortly after booting, before any console output appears.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Eryu Guan reported that loading scsi_debug would fail. This turned out
to be caused by scsi_debug reporting an optimal I/O size of 32KB which
is smaller than the 64KB page size on the PowerPC system in question.
Add a check to ensure that we only use the device-reported OPTIMAL
TRANSFER LENGTH if it is bigger than or equal to the page cache size.
Reported-by: Eryu Guan <guaneryu@gmail.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull ARM SoC fixes from Arnd Bergmann:
"This is the final small set of ARM SoC bug fixes for linux-4.4, almost
all regressions:
OMAP:
- data corruption on the Nokia N900 flash
Allwinner:
- Two defconfig change to get USB working again
ARM Versatile:
- Interrupt numbers gone bad after an older bug fix
Nomadik:
- Crashes from incorrect L2 cache settings
VIA vt8500:
- SD/MMC support on WM8650 never worked"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dts: vt8500: Add SDHC node to DTS file for WM8650
ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices
ARM: versatile: fix MMC/SD interrupt assignment
ARM: nomadik: set latencies to 8 cycles
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
ARM: Fix broken USB support in sunxi_defconfig
For 32-bit config reads (size == 4), hisi_pcie_cfg_read() returned success
but never filled in the data we read.
Return the register data for 32-bit config reads.
Without this fix, PCI doesn't work at all because enumeration depends on
32-bit config reads. The driver was tested internally, but got broken in
the process of upstreaming, so this fixes the breakage.
Fixes: 500a1d9a43e0 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit 49718f0fb8c9 ("SCSI: Fix NULL pointer dereference in
runtime PM")
The old commit may lead to a issue that blk_{pre|post}_runtime_suspend and
blk_{pre|post}_runtime_resume may not be called in pairs.
Take sr device as example, when sr device goes to runtime suspend,
blk_{pre|post}_runtime_suspend will be called since sr device defined
pm->runtime_suspend. But blk_{pre|post}_runtime_resume will not be called
since sr device doesn't have pm->runtime_resume. so, sr device can not
resume correctly anymore.
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull KVM fix from Paolo Bonzini:
"A simple fix. I'm sending it before the merge window, because it
refines a patch found in your master branch but not yet in the
kvm/next branch that is destined for 4.5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: only channel 0 of the i8254 is linked to the HPET
Pull "urgent onenand file system corruption fix for n900" from Tony Lindgren:
Last minute urgent pull request to prevent file system corruption
on Nokia N900.
Looks like we have a GPMC bus timing bug that has gone unnoticed
because of bootloader configured registers until few days ago. We
are not detecting the onenand clock rate properly unless we have
CONFIG_OMAP_GPMC_DEBUG set and this causes onenand corruption
that can be easily be reproduced.
There seems to be also an additional bug still lurking around for
onenand corruption. But that is still being investigated and
it does not seem to be GPMC timings related.
Meanwhile, it would be good to get this fix into v4.4 to prevent
wrong timings from corrupting onenand.
* tag 'omap-for-v4.4/onenand-corruption' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
PCI interrupt lines start at 1, not at 0. So, creates additional one
interrupt when register for irq domain.
Error when PCIe devices have 4 INTx:
WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:280
irq_domain_associate+0x17c/0x1cc()
error: hwirq 0x4 is too large for dummy
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While setting the KVM PIT counters in 'kvm_pit_load_count', if
'hpet_legacy_start' is set, the function disables the timer on
channel[0], instead of the respective index 'channel'. This is
because channels 1-3 are not linked to the HPET. Fix the caller
to only activate the special HPET processing for channel 0.
Reported-by: P J P <pjp@fedoraproject.org>
Fixes: 0185604c2d82c560dab2f2933a18f797e74ab5a8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Reviewed-by: Alexey Charkov <alchark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
unified the GPMC debug for the SoCs with GPMC. The commit also left out
the option for HWMOD_INIT_NO_RESET as we now require proper timings for
GPMC to be able to remap GPMC devices out of address 0.
Unfortunately on Nokia N900, onenand now only partially works with the
device tree provided timings. It works enough to get detected but the
clock rate supported by the onenand chip gets misdetected. This in turn
causes the GPMC timings to be miscalculated and this leads into file
system corruption on N900.
Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync
write. This is needed also for async timings when we write to onenand
with omap2_onenand_set_async_mode(). Without sync write bit set, the
async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff.
Let's exit with an error if onenand rate is not detected. And let's
remove the extra call to omap2_onenand_set_async_mode() as we only need
to do this once at the end of omap2_onenand_setup_async().
Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Check TLP packet successful completion status. This fix the issue when
accessing multi-function devices in enumeration process, TLP will return
error when accessing non-exist function number. Returns PCI error code
instead of generic errno.
Tested on Ethernet adapter card with multi-functions.
[bhelgaas: simplify completion status checking code]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"A handful of x86 fixes:
- a syscall ABI fix, fixing an Android breakage
- a Xen PV guest fix relating to the RTC device, causing a
non-working console
- a Xen guest syscall stack frame fix
- an MCE hotplug CPU crash fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/numachip: Fix NumaConnect2 MMCFG PCI access
x86/entry: Restore traditional SYSENTER calling convention
x86/entry: Fix some comments
x86/paravirt: Prevent rtc_cmos platform device init on PV guests
x86/xen: Avoid fast syscall path for Xen PV guests
x86/mce: Ensure offline CPUs don't participate in rendezvous process
Commit 69fb4dcada77 ("power: Add an axp20x-usb-power driver") introduced a
new driver for the USB power supply used on various Allwinner based SBCs.
However, the driver was not added to multi_v7_defconfig which breaks USB
support for some boards (e.g. LeMaker BananaPi) as the kernel will now
turn off the USB power supply during boot by default if the driver isn't
present. (This was not the case in linux 4.3 or lower where the USB power
was always left on.)
Hence, add the driver to multi_v7_defconfig in order to keep USB support
working on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Requester ID should use the Root Port devfn and it should be always 0.
Previously we constructed the Requester ID using the *Completer* devfn,
i.e., the devfn of the Function we expect to respond to the config access.
This causes issues when accessing configuration space for devices other
than the Root Port.
Build the Requester ID using the Root Port devfn.
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
Pull scheduler fixes from Ingo Molnar:
"Misc scheduler fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Reset task's lockless wake-queues on fork()
sched/core: Fix unserialized r-m-w scribbling stuff
sched/core: Check tgid in is_global_init()
sched/fair: Fix multiplication overflow on 32-bit systems
The MMCFG PCI accessors weren't being setup for NumacConnect2
correctly due to over-early assignment; this would create the
potential for the wrong PCI domain to be accessed.
Fix this by using the correct arch-specific PCI init function.
Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Acked-by: Steffen Persvold <sp@numascale.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1451498807-15920-1-git-send-email-daniel@numascale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull MIPS build fix from Ralf Baechle:
"Fix a makefile issue resulting in build breakage with older binutils.
This has sat in -next for a few days, testers and buildbot are happy
with it, too though if you are going for another -rc that'd certainly
help ironing out a few more issues"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: VDSO: Fix build error with binutils 2.24 and earlier
Commit 0976c946a610d06e907335b7a3afa6db046f8e1b
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.
However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.
Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.
For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.
Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.
Cc: Rob Herring <robh@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 0976c946a610 ("arm/versatile: Fix versatile irq specifications")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TLP_LOOP is 500 and the "loop" variable was a u8 so "loop < TLP_LOOP" is
always true. We only need this condition to work if there is a problem so
it would have been easy to miss this in testing.
Make it a normal for loop with "int i" instead of over thinking things and
making it complicated.
Fixes: 6bb4dd154ae8 ("PCI: altera: Add Altera PCIe host controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
Pull perf fixes from Ingo Molnar:
"Two core subsystem fixes, plus a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix race in swevent hash
perf: Fix race in perf_event_exec()
perf list: Robustify event printing routine
perf list: Add support for PERF_COUNT_SW_BPF_OUT
perf hists browser: Fix segfault if use symbol filter in cmdline
perf hists browser: Reset selection when refresh
perf hists browser: Add NULL pointer check to prevent crash
perf buildid-list: Fix return value of perf buildid-list -k
perf buildid-list: Show running kernel build id fix
In the following commit:
7675104990ed ("sched: Implement lockless wake-queues")
we gained lockless wake-queues.
The -RT kernel managed to lockup itself with those. There could be multiple
attempts for task X to enqueue it for a wakeup _even_ if task X is already
running.
The reason is that task X could be runnable but not yet on CPU. The the
task performing the wakeup did not leave the CPU it could performe
multiple wakeups.
With the proper timming task X could be running and enqueued for a
wakeup. If this happens while X is performing a fork() then its its
child will have a !NULL `wake_q` member copied.
This is not a problem as long as the child task does not participate in
lockless wakeups :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 7675104990ed ("sched: Implement lockless wake-queues")
Link: http://lkml.kernel.org/r/20151221171710.GA5499@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It turns out that some Android versions hardcode the SYSENTER
calling convention. This is buggy and will cause problems no
matter what the kernel does. Nonetheless, we should try to
support it.
Credit goes to Linus for pointing out a clean way to handle
the SYSENTER/SYSCALL clobber differences while preserving
straightforward DWARF annotations.
I believe that the original offending Android commit was:
https://android.googlesource.com/platform%2Fbionic/+/7dc3684d7a2587e43e6d2a8e0e3f39bf759bd535
Reported-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: <mark.gross@intel.com>
Cc: Su Tao <tao.su@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: <frank.wang@intel.com>
Cc: <borun.fu@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Mingwei Shi <mingwei.shi@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull i915 drm fixes from Jani Nikula:
"Two display fixes still for v4.4.
The new year's resolution is to start using signed tags per Linus'
request. This one is still unsigned; I want to fix this up in our
maintainer scripts instead of doing it one-off"
* tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: increase the tries for HDMI hotplug live status checking
drm/i915: Unbreak check_digital_port_conflicts()
Commit 2a037f310bab ("MIPS: VDSO: Fix build error") tries to fix a build
error seen with binutils 2.24 and earlier. However, the fix does not work,
and again results in the already known build errors if the kernel is built
with an earlier version of binutils.
CC arch/mips/vdso/gettimeofday.o
/tmp/ccnOVbHT.s: Assembler messages:
/tmp/ccnOVbHT.s:50: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
/tmp/ccnOVbHT.s:374: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
scripts/Makefile.build:258: recipe for target 'arch/mips/vdso/gettimeofday.o' failed
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
Fixes: 2a037f310bab ("MIPS: VDSO: Fix build error")
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11926/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.
These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct
device::msi_domain"), we use the MSI domain associated with the PCI device.
But finding an MSI domain doesn't mean that the domain is implemented using
the generic MSI domain API, and a number of MSI controllers are still using
arch_setup_msi_irq() and arch_teardown_msi_irqs().
Check that the domain we just obtained is hierarchical. If it is, we can
use the new generic MSI stuff. Otherwise we have to fall back to the old
arch_setup_msi_irq() and arch_teardown_msi_irqs() interfaces.
This avoids an oops in msi_domain_alloc_irqs() on systems with R-Car,
Tegra, Armada 370, and probably other DesignWare-based host controllers.
Fixes: d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct device::msi_domain")
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Tested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
CC: stable@vger.kernel.org # v4.3+
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
CPU0 CPU1
set_current_state(...)
<preempt_schedule>
context_switch(X, Y)
prepare_lock_switch(Y)
Y->on_cpu = 1;
finish_lock_switch(X)
store_release(X->on_cpu, 0);
try_to_wake_up(X)
LOCK(p->pi_lock);
t = X->on_cpu; // 0
context_switch(Y, X)
prepare_lock_switch(X)
X->on_cpu = 1;
finish_lock_switch(Y)
store_release(Y->on_cpu, 0);
</preempt_schedule>
schedule();
deactivate_task(X);
X->on_rq = 0;
if (X->on_rq) // false
if (t) while (X->on_cpu)
cpu_relax();
context_switch(X, ..)
finish_lock_switch(X)
store_release(X->on_cpu, 0);
Avoid the load of X->on_cpu being hoisted over the X->on_rq load.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's a race on CPU unplug where we free the swevent hash array
while it can still have events on. This will result in a
use-after-free which is BAD.
Simply do not free the hash array on unplug. This leaves the thing
around and no use-after-free takes place.
When the last swevent dies, we do a for_each_possible_cpu() iteration
anyway to clean these up, at which time we'll free it, so no leakage
will occur.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the sched bitfieds (notably sched_reset_on_fork) can be set
on other than current, this can cause the r-m-w to race with other
updates.
Since all the sched bits are serialized by scheduler locks, pull them
in a separate word.
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: hannes@cmpxchg.org
Cc: mhocko@kernel.org
Cc: vdavydov@parallels.com
Link: http://lkml.kernel.org/r/20151125150207.GM11639@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: <mark.gross@intel.com>
Cc: Su Tao <tao.su@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: <qiuxu.zhuo@intel.com>
Cc: <frank.wang@intel.com>
Cc: <borun.fu@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Mingwei Shi <mingwei.shi@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull PCI bugfix from Bjorn Helgaas:
"Here's another fix for v4.4.
This fixes 32-bit config reads for the HiSilicon driver. Obviously
the driver is completely broken without this fix (apparently it
actually was tested internally, but got broken somehow in the process
of upstreaming it).
Summary:
HiSilicon host bridge driver
Fix 32-bit config reads (Dongdong Liu)"
* tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads
The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.
After doing experiments for following monitors, it needs 80ms at least
for those worst cases.
Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)
It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.com
Tested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c693d ("drm/i915: Check live status before reading edid")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea0053b23de42c828d559016eabe0b91523)
[Jani: undo the file mode change of the original commit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 69fb4dcada77 ("power: Add an axp20x-usb-power driver") introduced a new
driver for the USB power supply used on various Allwinner based SBCs. However,
the driver was not added to sunxi_defconfig which breaks USB support for some
boards (e.g. LeMaker BananaPi) as the kernel will now turn off the USB power
supply during boot by default if the driver isn't present. (This was not the
case in linux 4.3 or lower where the USB power was always left on.)
Hence, add the driver to sunxi_defconfig in order to keep USB support working
on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Reported-by: David Tulloh <david@tulloh.id.au>
Tested-by: David Tulloh <david@tulloh.id.au>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b3a72384fe29 ("ARM/PCI: Replace pci_sys_data->align_resource with
global function pointer") introduced an ARM-specific align_resource()
function pointer. This is not portable to other arches and doesn't work
for platforms with two different PCIe host bridge controllers.
Move the function pointer to the pci_host_bridge structure so each host
bridge driver can specify its own align_resource() function.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag