.. and this should hopefully be the last -rc before final 3.4 release.

Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:

- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"

A set of PCH bug fixes, and one patch to fix up compile warnings

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers

* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board

Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.

Fixes the following compiler warnings:

drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]

drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

It should be (1 << 2) for ctrlbit of exynos5_clk_pdma1.

Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pull networking fixes from David S. Miller:

1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.

2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.

3) Fix PM resume locking in IGB driver, from Benjamin Poirier.

4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.

5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.

6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.

7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.

8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.

9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.

10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.

11) Fix pktgen OOPS on module unload, from Eric Dumazet.

12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.

13) Cure division by zero in SFC driver, from Ben Hutchings.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...

Fix a use-after-free in the TMF path, where cmd may have been already
freed by virtscsi_complete_free when wait_for_completion restarts
executing virtscsi_tmf. Technically a race, but in practice the command
will always be freed long before the completion waiter is awoken.

The fix is to make callers specifying a completion responsible for
freeing the command in all cases.

Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Jean-Francois Dagenais reported:

Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.

The driver is wrong in several ways:

1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.

2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.

3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.

Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.

Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).

Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Fix two board spefific regressions and one regression caused by bad documentation

By Archit Taneja (1) and others
via Tony Lindgren
* tag 'omap-fixes-for-v3.4-rc6-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: igep0020: fix smsc911x dummy regulator id
ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler

Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.

Thanks to imx and tegra guys for actual code.

Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.

Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."

* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton

If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6f381fa344911d5a234b13574433cf23036f9467
Author: Lin Ming <ming.m.lin@intel.com>

[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue

Caused a regression where we oops in every legacy mode SCSI host driver
because they supply a NULL pointer to scsi_add_host(). Fix this by checking
for the NULL in scsi_add_host_with_dma() and changing the DMA device to being
the platform_bus in that case (which replicates the original behaviour).

Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.

Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.

Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.

Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

By Ben Hutchings (1) and Ian Campbell (1)
via Jason Cooper: "ARM: kirkwood: fixes for v3.4"
* 'kirkwood_fixes_for_v3.4' of git://git.infradead.org/users/jcooper/linux-kirkwood:
ARM: orion5x: Fix GPIO enable bits for MPP9
ARM: kirkwood: add missing kexec.h include

id 0 is already used and causes errors at boot:

WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'

Fix it by using the next available one (id=1).

This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.

Signed-off-by: Enrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix SMP TWD boot regression on sh73a0 based platforms caused by:

4200b16 ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

This patch removed shmobile_twd_init() which is no longer needed

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Since cpufreq has no official maintainer at the moment, I'm willing
to maintain it along some other power management core code I've been
maintaining already.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the requested scsi_dh module is already loaded then skip
request_module().

Multipath table loads can hang in an unnecessary __request_module.

Reported-by: Ben Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.

Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Commit 554cdaefd1cf7bb54b209c4e68c7cec87ce442a9 ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only). For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:

[ 12.711476] leds-gpio: probe of leds-gpio failed with error -22

Reported-by: Henry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [v3.0+]
Tested-by: Hans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This reverts commit 46f8c3c7e95c0d30d95911e7975ddc4f93b3e237.

The commit above swapped the DSI1_PPID and DSI2_PPID register fields in
CONTROL_DSIPHY to be in sync with the newer public OMAP TRMs(after version V).

With this commit, contention errors were reported on DSI lanes some OMAP4 SDPs.
After probing the DSI lanes on OMAP4 SDP, it was seen that setting bits in the
DSI2_PPID field was pulling up voltage on DSI1 lanes, and DSI1_PPID field was
pulling up voltage on DSI2 lanes.

This proves that the current version of OMAP4 TRM is incorrect, swap the
position of register fields according to the older TRM versions as they were
correct.

Cc: stable@vger.kernel.org # v3.2+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix SMP TWD boot regression on r8a7779 based platforms caused by:

4200b16 ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Pull x86 fixes form Peter Anvin

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
x86, relocs: Remove an unused variable
asm-generic: Use __BITS_PER_LONG in statfs.h
x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it

Pull GPIO omap bug fix from Grant Likely.

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/omap: fix incorrect initialization of omap_gpio_mod_init

Remove duplicate copy of string "device-mapper" (DM_NAME) from
MODULE_DESCRIPTION.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Take vlan header length into account, when vlan id is stored as
vlan_tci. Otherwise tagged packets coming from macvtap will be
truncated.

Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[jejb: checkpatch fixes]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixes the following build error when CONFIG_KEXEC is enabled:
CC arch/arm/mach-kirkwood/board-dt.o
arch/arm/mach-kirkwood/board-dt.c: In function 'kirkwood_dt_init':
arch/arm/mach-kirkwood/board-dt.c:52:2: error: 'kexec_reinit' undeclared (first use in this function)
arch/arm/mach-kirkwood/board-dt.c:52:2: note: each undeclared identifier is reported only once for each function it appears in

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
[v4, rebase onto recent Linus for repost]
[v3, speak actual English in the commit message, thanks Sergei Shtylyov]
[v2, using linux/kexec.h not asm/kexec.h]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Commit 384ebe1c2849160d040df3e68634ec506f13d9ff, "gpio/omap: Add DT
support to GPIO driver", introduced dynamic IRQ numbering of OMAP GPIO
interrupts, breaking all IH_GPIO_BASE based IRQ number calculations.
This issue was corrected in the OMAP GPIO driver and the related header
file with commit 25db711df3258d125dc1209800317e5c0ef3c870, "gpio/omap:
Fix IRQ handling for SPARSE_IRQ".

However, the Amstrad Delta FIQ handler, which replaces the gpio-omap
driver in serving GPIO interrupts on this board, still uses that
outdated method. Fix it.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This also fixes the following modular mmc build failure:

arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'

on this platform by eliminating the use of an inline function, which
calls into the mmc core.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Pull btrfs fixes from Chris Mason:
"The big ones here are a memory leak we introduced in rc1, and a
scheduling while atomic if the transid on disk doesn't match the
transid we expected. This happens for corrupt blocks, or out of date
disks.

It also fixes up the ioctl definition for our ioctl to resolve logical
inode numbers. The __u32 was a merging error and doesn't match what
we ship in the progs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: avoid sleeping in verify_parent_transid while atomic
Btrfs: fix crash in scrub repair code when device is missing
btrfs: Fix mismatching struct members in ioctl.h
Btrfs: fix page leak when allocing extent buffers
Btrfs: Add properly locking around add_root_to_dirty_list

So that the power button still wakes up the platform.

Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Link: http://lkml.kernel.org/r/20120504210244.F2EA5A018B@akpm.mtv.corp.google.com
Tested-by: Kangkai Yin <kangkai.yin@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Pull another powerpc irq fix from Benjamin Herrenschmidt:
"It looks like my previous fix for the lazy irq masking problem wasn't
quite enough. There was another problem related to performance
monitor interrupts acting as NMIs leaving the flags in an incorrect
state. Here's a fix that finally seems to make perf solid again."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/irq: Fix another case of lazy IRQ state getting out of sync

Fix two places in commit 104655fd4dce ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.

Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:

WARNING: at lib/list_debug.c:32 __list_add+0x8f/0xa0()
...
list_add corruption. next->prev should be prev (ffff880323b96140), but was ffff8801d2c48440. (next=ffff8801d2c485c0).
...
Pid: 17205, comm: kworker/u:1 Tainted: G W O 3.4.0-rc3.snitm+ #1
Call Trace:
[<ffffffff8103ca1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103cb16>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa04f6ce6>] ? bio_detain+0xc6/0x210 [dm_thin_pool]
[<ffffffff8124ff3f>] __list_add+0x8f/0xa0
[<ffffffffa04f70d2>] process_discard+0x2a2/0x2d0 [dm_thin_pool]
[<ffffffffa04f6a78>] ? remap_and_issue+0x38/0x50 [dm_thin_pool]
[<ffffffffa04f7c3b>] process_deferred_bios+0x7b/0x230 [dm_thin_pool]
[<ffffffffa04f7df0>] ? process_deferred_bios+0x230/0x230 [dm_thin_pool]
[<ffffffffa04f7e42>] do_worker+0x52/0x60 [dm_thin_pool]
[<ffffffff81056fa9>] process_one_work+0x129/0x450
[<ffffffff81059b9c>] worker_thread+0x17c/0x3c0
[<ffffffff81059a20>] ? manage_workers+0x120/0x120
[<ffffffff8105eabe>] kthread+0x9e/0xb0
[<ffffffff814ceda4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105ea20>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff814ceda0>] ? gs_change+0x13/0x13
---[ end trace 7e0a523bc5e52692 ]---

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.

Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This also fixes the following modular mmc build failure:

arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'

on this platform by eliminating the use of an inline function, which
calls into the mmc core.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there. Switch to use of set_personality_ia32()...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.

But, a few callers are using it with spinlocks held. Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case. This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.

Signed-off-by: Chris Mason <chris.mason@oracle.com>

It seems that there was an error with the active_low = 1 for the
LED, since it should be set to 0 (meaning that active is high,
since 0 is false, hence the confusion.

The wiki article about it confuses it, since it contradicts itself,
regarding what turns on the LED.

I have tested 3.4-rc2 on my net5501 with this patch, and it makes the LED
behave correctly, where "none" turns it off, and "default-on" turns it on,
when echoed onto the trigger "file" in /sys/class/leds.

Signed-off-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Link: http://lkml.kernel.org/r/20120504210146.62186A018B@akpm.mtv.corp.google.com
Cc: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.

That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.

This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."

* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion

So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.

This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.

This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit
6f94a4c45a6f744383f9f695dde019998db3df55 ("dm thin: fix stacked bi_next
usage").

A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.

In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).

Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.

In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.

Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.

The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).

To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."

* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering

Pull alpha fixes from Matt Turner:
"My alpha tree is back up (after taking quite some time to get my GPG
key signed). It contains just some simple fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: silence 'const' warning in sys_marvel.c
alpha: include module.h to fix modpost on Tsunami
alpha: properly define get/set_rtc_time on Marvel/SMP
alpha: VGA_HOSE depends on VGA_CONSOLE

Fix that when scrub tries to repair an I/O or checksum error and one of
the devices containing the mirror is missing, it crashes in bio_add_page
because the bdev is a NULL pointer for missing devices.

Reported-by: Marco L. Crociani <marco.crociani@gmail.com>
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

sh_symtab is set but not used.

[ hpa: putting this in urgent because of the sheer harmlessness of the patch:
it quiets a build warning but does not change any generated code. ]

Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: http://lkml.kernel.org/r/20120401082932.D5E066FC03D@msa105.auone-net.jp
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>

Pull a m68knommu fix from Greg Ungerer:
"It contains a single fix for including the ColdFire QSPI interface
setup code when enabled as a module. This was broken in the
consolidation of the ColdFire SoC device tables in the 3.4 merge
window."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable qspi support when SPI_COLDFIRE_QSPI = m

This patch removes some potentially problematic legacy code within
core_clear_initiator_node_from_tpg() that was originally intended to
release left over se_lun_acl setup during dynamic NodeACL+MappedLUN
generate when running with TPG demo-mode operation.

Since we now only ever expect to allocate and release se_lun_acl from
within target_core_fabric_configfs.c:target_fabric_make_mappedlun() and
target_fabric_drop_mappedlun() context respectively, this code for
demo-mode release is incorrect and needs to be removed.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>