tjh.dev
commits
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82bae: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
I have moved, I do not have the hardware access anymore.
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since commit 6d178ef2fd5e ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Change ownership of the hpsa driver from Stephen M. Cameron
(Hewlett-Packard) to Don Brace (PMC-Sierra).
Change ownership of the cciss driver from Mike Miller (Hewlett-Packard)
to Don Brace (PMC-Sierra).
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613af ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a
very significant drop in networking performance. The test were
conducted on an OpenBlocks A7 board. Without this patch, the outgoing
performance measured with iperf are:
- highmem OFF, TSO OFF 544 Mbit/s
- highmem OFF, TSO ON 942 Mbit/s
- highmem ON, TSO OFF 306 Mbit/s
- highmem ON, TSO ON 246 Mbit/s
On this Kirkwood platform, the L2 cache is a Feroceon cache, and with
this cache, all the range operations have to be done on virtual
addresses and not physical addresses. Therefore, whenever
CONFIG_HIGHMEM is enabled, the cache maintenance operations call
kmap_atomic_pfn() and kunmap_atomic().
However, kmap_atomic_pfn() does not implement the same fast path for
non-highmem pages as the one implemented in kmap_atomic(), and this is
one of the reason for the performance drop. While this patch does not
fully restore the performances, it clearly improves them a lot:
without patch with patch
- highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s
- highmem ON, TSO ON 246 Mbit/s 434 Mbit/s
We're still far from the !CONFIG_HIGHMEM performances, but it does
improve a bit the situation.
Thanks a lot to Ezequiel Garcia and Gregory Clement for all the
testing work around this topic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
libcxgbi was always returning an ipv4 address for ISCSI_HOST_PARAM_IPADDRESS,
return appropriate address based on address family
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
Most call paths to vmx_vcpu_reset do not hold the SRCU lock. Defer loading
the APIC access page to the next vmentry.
This avoids the following lockdep splat:
[ INFO: suspicious RCU usage. ]
3.18.0-rc2-test2+ #70 Not tainted
-------------------------------
include/linux/kvm_host.h:474 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-x86/2371:
#0: (&vcpu->mutex){+.+...}, at: [<ffffffffa037d800>] vcpu_load+0x20/0xd0 [kvm]
stack backtrace:
CPU: 4 PID: 2371 Comm: qemu-system-x86 Not tainted 3.18.0-rc2-test2+ #70
Hardware name: Dell Inc. OptiPlex 9010/0M9KCM, BIOS A12 01/10/2013
0000000000000001 ffff880209983ca8 ffffffff816f514f 0000000000000000
ffff8802099b8990 ffff880209983cd8 ffffffff810bd687 00000000000fee00
ffff880208a2c000 ffff880208a10000 ffff88020ef50040 ffff880209983d08
Call Trace:
[<ffffffff816f514f>] dump_stack+0x4e/0x71
[<ffffffff810bd687>] lockdep_rcu_suspicious+0xe7/0x120
[<ffffffffa037d055>] gfn_to_memslot+0xd5/0xe0 [kvm]
[<ffffffffa03807d3>] __gfn_to_pfn+0x33/0x60 [kvm]
[<ffffffffa0380885>] gfn_to_page+0x25/0x90 [kvm]
[<ffffffffa038aeec>] kvm_vcpu_reload_apic_access_page+0x3c/0x80 [kvm]
[<ffffffffa08f0a9c>] vmx_vcpu_reset+0x20c/0x460 [kvm_intel]
[<ffffffffa039ab8e>] kvm_vcpu_reset+0x15e/0x1b0 [kvm]
[<ffffffffa039ac0c>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
[<ffffffffa037f7e0>] kvm_vm_ioctl+0x1d0/0x780 [kvm]
[<ffffffff810bc664>] ? __lock_is_held+0x54/0x80
[<ffffffff812231f0>] do_vfs_ioctl+0x300/0x520
[<ffffffff8122ee45>] ? __fget+0x5/0x250
[<ffffffff8122f0fa>] ? __fget_light+0x2a/0xe0
[<ffffffff81223491>] SyS_ioctl+0x81/0xa0
[<ffffffff816fed6d>] system_call_fastpath+0x16/0x1b
Reported-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Fixes: 38b9917350cb2946e368ba684cfc33d1672f104e
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Russell King suggested [1]:
"I'd ask for one change. Please make all these messages start with
"L2C-310 OF" not "PL310 OF:". The device is described in ARM
documentation as a L2C-310 not PL310. (Also note the : is dropped
too - most of the other messages don't have the : either.)
The:
"PL310 OF: cache setting yield illegal associativity
PL310 OF: -1073346556 calculated, only 8 and 16 legal"
message could also be changed to something like:
"L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn"
[1] http://www.spinics.net/lists/arm-kernel/msg372776.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- dpm stability fixes for SI and KV
- remove an invalid pci id
- kmalloc_array fixes
- minor cleanups
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: remove some buggy dead code
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.
v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To generate the right SPI tag messages we need to properly set
QUEUE_FLAG_QUEUED in the request_queue and mirror it to the
request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 513510ddba9650fc7da456eefeb0ead7632324f6
(common: dma-mapping: introduce common remapping functions)
managed to end up with an extra return statement from the
original patch. Drop it.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bunch of DP fixes, and some backlight fix.
* tag 'drm-intel-fixes-2014-10-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
drm/i915: Do a dummy DPCD read before the actual read
The calculation of "num_shader_engines" has a precedence bug because
the right shift happens before the mask, but this variable is never used
so we can just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hash key computation in vmw_cmdbuf_res_remove incorrectly didn't take
the resource type into account, contrary to all the other related functions.
This becomes important when the cmdbuf resource manager handles more than
one resource type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit fb3ccb5da71273e7f0d50b50bc879e50cedd60e7.
SCSI-2/SPI actually needs the tagged/untagged flag in the request to
work properly. Revert this patch and add a follow on to set it in
the right place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
The MTD_NAND_OMAP_BCH doesn't harm on legacy OMAP platforms
so don't state that it should be disabled for them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit f3354ab67476dc80 ("ARM: 8169/1: l2c: parse cache properties from
ePAPR definitions") the following error is seen on imx6q:
[ 0.000000] PL310 OF: cache setting yield illegal associativity
[ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal
As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized.
To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Three changes for the Armada DRM driver:
1. Add back the flags which tell the DRM core that we can do vblank. This
was removed in error during the recent restructuring, and came to light
while trying textured Xv rendering.
2. Fixing a refcount leak with Xv overlay.
3. As per recent discussion, the drm_vblank_pre_modeset() calls can cause
deadlock with other changes to generic code. This change prevents those
deadlocks by switching to the drm_crtc_vblank_*() calls instead.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: convert to use vblank_on/off calls
drm/armada: fix page_flip refcounting leak
drm/armada: add IRQ support back
Ivybridge + 30" monitor prints a drm error on every modeset, since IVB
doesn't support DP3 we should even bother trying to use it.
This regression has been introduced in
commit 06ea66b6bb445043dc25a9626254d5c130093199
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable
devices
Reported-by: Dave Airlie <airlied@redhat.com>
Reference: http://mid.gmane.org/1414566170-9868-1-git-send-email-airlied@gmail.com
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
0x4c6e is a secondary device id so should not be used
by the driver.
Noticed-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After:
commit d059f652e73c35678d28d4cd09ab2cec89696af9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Fri Jul 25 18:07:40 2014 +0200
drm: Handle legacy per-crtc locking with full acquire ctx
drm_mode_cursor_common() was switched to use drm_modeset_(un)lock_crtc()
which uses full aquire ctx. So dropping/reaquiring the lock via
drm_modeset_(un)lock() directly isn't the right thing to do, as lockdep
kindly points out.
The 'FIXME's about sorting out whether vmwgfx *really* needs to lock-all
for cursor updates still apply.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
In case of error during plane initialization load callback
incorrectly return success, this patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
Fixes: c53c6d6a68b1 ("scatterlist: allow chaining to preallocated chunks")
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This commit adds a hidden option to build the omap_elm as a module, if
omap2_nand is a module (and similarly in the built-in case).
This fixes the following build error when omap2_nand is chosen built-in,
and omap_elm is chosen as a module:
drivers/built-in.o: In function `omap_nand_probe':
drivers/mtd/nand/omap2.c:2010: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1980: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1927: undefined reference to `elm_config'
drivers/built-in.o: In function `omap_elm_correct_data':
drivers/mtd/nand/omap2.c:1444: undefined reference to `elm_decode_bch_error_page'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
As a follow-up to commit 6cab7a37f5c04 ("staging: comedi: (regression)
channel list must be set for COMEDI_CMD ioctl"), Hartley Sweeten pointed
out another couple of bugs stemming from commit 6cab7a37f5c04 ("staging:
comedi: comedi_fops: introduce __comedi_get_user_chanlist()").
Firstly, `do_cmdtest_ioctl()` never frees the kernel copy of the user
chanlist allocated by `__comedi_get_user_chanlist()`, so that memory is
leaked. Fix it by freeing the allocated kernel memory pointed to by
`cmd.chanlist` before that pointer is overwritten with its original
pointer to user memory before `cmd` is copied back to user-space.
Secondly, if `__comedi_get_user_chanlist()` returns an error,
`cmd->chanlist` is left unchanged and in fact will be a pointer to user
memory. This causes `do_cmd_ioctl()` to `goto cleanup` and call
`do_become_nonbusy()` which would attempt to free the memory pointed to
by the user-space pointer. Fix it by setting `cmd->chanlist` to NULL at
the start of `__comedi_get_user_chanlist()`.
Fixes: c6cd0eefb27b ("staging: comedi: comedi_fops: introduce __comedi_get_user_chanlist()")
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y: 6cab7a37f5c04
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we only need it for joliet and case-insensitive mounts
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Emulation of code that is 14 bytes to the segment limit or closer
(e.g. RIP = 0xFFFFFFF2 after reset) is broken because we try to read as
many as 15 bytes from the beginning of the instruction, and __linearize
fails when the passed (address, size) pair reaches out of the segment.
To fix this, let __linearize return the maximum accessible size (clamped
to 2^32-1) for usage in __do_insn_fetch_bytes, and avoid the limit check
by passing zero for the desired size.
For expand-down segments, __linearize is performing a redundant check.
(u32)(addr.ea + size - 1) <= lim can only happen if addr.ea is close
to 4GB; in this case, addr.ea + size - 1 will also fail the check against
the upper bound of the segment (which is provided by the D/B bit).
After eliminating the redundant check, it is simple to compute
the *max_size for expand-down segments too.
Now that the limit check is done in __do_insn_fetch_bytes, we want
to inject a general protection fault there if size < op_size (like
__linearize would have done), instead of just aborting.
This fixes booting Tiano Core from emulated flash with EPT disabled.
Cc: stable@vger.kernel.org
Fixes: 719d5a9b2487e0562f178f61e323c3dc18a8b200
Reported-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- a few compilation fixes with randconfigs
- one potential compilation breakage on userspace due to the usage of
a gcc extension
- several warnings fixed
- some other random driver fixes"
* tag 'media/v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (22 commits)
[media] s5p-jpeg: Avoid -Wuninitialized warning in s5p_jpeg_parse_hdr
[media] s5p-fimc: Only build suspend/resume for PM
[media] s5p-jpeg: Only build suspend/resume for PM
[media] Remove references to non-existent PLAT_S5P symbol
[media] videobuf-dma-contig: set vm_pgoff to be zero to pass the sanity check in vm_iomap_memory()
[media] tw68: remove bogus I2C_ALGOBIT dependency
[media] usbvision-video: two use after frees
[media] tw68: remove deprecated IRQF_DISABLED
[media] xc5000: use after free in release()
[media] em28xx-input: NULL dereference on error
[media] wl128x: fix fmdbg compiler warning
Revert "[media] v4l2-dv-timings: fix a sparse warning"
[media] hackrf: harmless off by one in debug code
[media] cx23885: initialize config structs for T9580
[media] v4l: uvcvideo: Fix buffer completion size check
[media] vivid: fix buffer overrun
[media] saa7146: Create a device name before it's used
[media] em28xx: fix uninitialized variable warning
[media] vivid: fix Kconfig FB dependency
[media] anysee: make sure loading modules is const
...
A future commit changes the way various vblank calls behave, which
causes drivers to break. Converting to use the drm_crtc_vblank_on/off
calls avoids this breakage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit c675949ec58ca50d5a3ae3c757892f1560f6e896
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
prevents backlight setup on Macbook 2,1. Apply quirk to ignore the VBT
check so backlight is set up properly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81438
Signed-off-by: Jens Stein Jørgensen <jens.s.stein@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
- bapm seems to cause CPU stuck messages so disable it.
- nb dpm seems to prevent GPU dpm from getting enabled, so
disable it.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=85107
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
encoder object isn't used anymore so remove it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks
Johan writes:
USB-serial fixes for v3.18-rc3
These updates remove two allocations of unused buffers from kobil_sct
and add some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82bae: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
Since commit 6d178ef2fd5e ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Change ownership of the hpsa driver from Stephen M. Cameron
(Hewlett-Packard) to Don Brace (PMC-Sierra).
Change ownership of the cciss driver from Mike Miller (Hewlett-Packard)
to Don Brace (PMC-Sierra).
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613af ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a
very significant drop in networking performance. The test were
conducted on an OpenBlocks A7 board. Without this patch, the outgoing
performance measured with iperf are:
- highmem OFF, TSO OFF 544 Mbit/s
- highmem OFF, TSO ON 942 Mbit/s
- highmem ON, TSO OFF 306 Mbit/s
- highmem ON, TSO ON 246 Mbit/s
On this Kirkwood platform, the L2 cache is a Feroceon cache, and with
this cache, all the range operations have to be done on virtual
addresses and not physical addresses. Therefore, whenever
CONFIG_HIGHMEM is enabled, the cache maintenance operations call
kmap_atomic_pfn() and kunmap_atomic().
However, kmap_atomic_pfn() does not implement the same fast path for
non-highmem pages as the one implemented in kmap_atomic(), and this is
one of the reason for the performance drop. While this patch does not
fully restore the performances, it clearly improves them a lot:
without patch with patch
- highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s
- highmem ON, TSO ON 246 Mbit/s 434 Mbit/s
We're still far from the !CONFIG_HIGHMEM performances, but it does
improve a bit the situation.
Thanks a lot to Ezequiel Garcia and Gregory Clement for all the
testing work around this topic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
libcxgbi was always returning an ipv4 address for ISCSI_HOST_PARAM_IPADDRESS,
return appropriate address based on address family
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
Most call paths to vmx_vcpu_reset do not hold the SRCU lock. Defer loading
the APIC access page to the next vmentry.
This avoids the following lockdep splat:
[ INFO: suspicious RCU usage. ]
3.18.0-rc2-test2+ #70 Not tainted
-------------------------------
include/linux/kvm_host.h:474 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-x86/2371:
#0: (&vcpu->mutex){+.+...}, at: [<ffffffffa037d800>] vcpu_load+0x20/0xd0 [kvm]
stack backtrace:
CPU: 4 PID: 2371 Comm: qemu-system-x86 Not tainted 3.18.0-rc2-test2+ #70
Hardware name: Dell Inc. OptiPlex 9010/0M9KCM, BIOS A12 01/10/2013
0000000000000001 ffff880209983ca8 ffffffff816f514f 0000000000000000
ffff8802099b8990 ffff880209983cd8 ffffffff810bd687 00000000000fee00
ffff880208a2c000 ffff880208a10000 ffff88020ef50040 ffff880209983d08
Call Trace:
[<ffffffff816f514f>] dump_stack+0x4e/0x71
[<ffffffff810bd687>] lockdep_rcu_suspicious+0xe7/0x120
[<ffffffffa037d055>] gfn_to_memslot+0xd5/0xe0 [kvm]
[<ffffffffa03807d3>] __gfn_to_pfn+0x33/0x60 [kvm]
[<ffffffffa0380885>] gfn_to_page+0x25/0x90 [kvm]
[<ffffffffa038aeec>] kvm_vcpu_reload_apic_access_page+0x3c/0x80 [kvm]
[<ffffffffa08f0a9c>] vmx_vcpu_reset+0x20c/0x460 [kvm_intel]
[<ffffffffa039ab8e>] kvm_vcpu_reset+0x15e/0x1b0 [kvm]
[<ffffffffa039ac0c>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
[<ffffffffa037f7e0>] kvm_vm_ioctl+0x1d0/0x780 [kvm]
[<ffffffff810bc664>] ? __lock_is_held+0x54/0x80
[<ffffffff812231f0>] do_vfs_ioctl+0x300/0x520
[<ffffffff8122ee45>] ? __fget+0x5/0x250
[<ffffffff8122f0fa>] ? __fget_light+0x2a/0xe0
[<ffffffff81223491>] SyS_ioctl+0x81/0xa0
[<ffffffff816fed6d>] system_call_fastpath+0x16/0x1b
Reported-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Fixes: 38b9917350cb2946e368ba684cfc33d1672f104e
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Russell King suggested [1]:
"I'd ask for one change. Please make all these messages start with
"L2C-310 OF" not "PL310 OF:". The device is described in ARM
documentation as a L2C-310 not PL310. (Also note the : is dropped
too - most of the other messages don't have the : either.)
The:
"PL310 OF: cache setting yield illegal associativity
PL310 OF: -1073346556 calculated, only 8 and 16 legal"
message could also be changed to something like:
"L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn"
[1] http://www.spinics.net/lists/arm-kernel/msg372776.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- dpm stability fixes for SI and KV
- remove an invalid pci id
- kmalloc_array fixes
- minor cleanups
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: remove some buggy dead code
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.
v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To generate the right SPI tag messages we need to properly set
QUEUE_FLAG_QUEUED in the request_queue and mirror it to the
request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
bunch of DP fixes, and some backlight fix.
* tag 'drm-intel-fixes-2014-10-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
drm/i915: Do a dummy DPCD read before the actual read
The hash key computation in vmw_cmdbuf_res_remove incorrectly didn't take
the resource type into account, contrary to all the other related functions.
This becomes important when the cmdbuf resource manager handles more than
one resource type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit fb3ccb5da71273e7f0d50b50bc879e50cedd60e7.
SCSI-2/SPI actually needs the tagged/untagged flag in the request to
work properly. Revert this patch and add a follow on to set it in
the right place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit f3354ab67476dc80 ("ARM: 8169/1: l2c: parse cache properties from
ePAPR definitions") the following error is seen on imx6q:
[ 0.000000] PL310 OF: cache setting yield illegal associativity
[ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal
As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized.
To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Three changes for the Armada DRM driver:
1. Add back the flags which tell the DRM core that we can do vblank. This
was removed in error during the recent restructuring, and came to light
while trying textured Xv rendering.
2. Fixing a refcount leak with Xv overlay.
3. As per recent discussion, the drm_vblank_pre_modeset() calls can cause
deadlock with other changes to generic code. This change prevents those
deadlocks by switching to the drm_crtc_vblank_*() calls instead.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: convert to use vblank_on/off calls
drm/armada: fix page_flip refcounting leak
drm/armada: add IRQ support back
Ivybridge + 30" monitor prints a drm error on every modeset, since IVB
doesn't support DP3 we should even bother trying to use it.
This regression has been introduced in
commit 06ea66b6bb445043dc25a9626254d5c130093199
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable
devices
Reported-by: Dave Airlie <airlied@redhat.com>
Reference: http://mid.gmane.org/1414566170-9868-1-git-send-email-airlied@gmail.com
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
After:
commit d059f652e73c35678d28d4cd09ab2cec89696af9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Fri Jul 25 18:07:40 2014 +0200
drm: Handle legacy per-crtc locking with full acquire ctx
drm_mode_cursor_common() was switched to use drm_modeset_(un)lock_crtc()
which uses full aquire ctx. So dropping/reaquiring the lock via
drm_modeset_(un)lock() directly isn't the right thing to do, as lockdep
kindly points out.
The 'FIXME's about sorting out whether vmwgfx *really* needs to lock-all
for cursor updates still apply.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
Fixes: c53c6d6a68b1 ("scatterlist: allow chaining to preallocated chunks")
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This commit adds a hidden option to build the omap_elm as a module, if
omap2_nand is a module (and similarly in the built-in case).
This fixes the following build error when omap2_nand is chosen built-in,
and omap_elm is chosen as a module:
drivers/built-in.o: In function `omap_nand_probe':
drivers/mtd/nand/omap2.c:2010: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1980: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1927: undefined reference to `elm_config'
drivers/built-in.o: In function `omap_elm_correct_data':
drivers/mtd/nand/omap2.c:1444: undefined reference to `elm_decode_bch_error_page'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
As a follow-up to commit 6cab7a37f5c04 ("staging: comedi: (regression)
channel list must be set for COMEDI_CMD ioctl"), Hartley Sweeten pointed
out another couple of bugs stemming from commit 6cab7a37f5c04 ("staging:
comedi: comedi_fops: introduce __comedi_get_user_chanlist()").
Firstly, `do_cmdtest_ioctl()` never frees the kernel copy of the user
chanlist allocated by `__comedi_get_user_chanlist()`, so that memory is
leaked. Fix it by freeing the allocated kernel memory pointed to by
`cmd.chanlist` before that pointer is overwritten with its original
pointer to user memory before `cmd` is copied back to user-space.
Secondly, if `__comedi_get_user_chanlist()` returns an error,
`cmd->chanlist` is left unchanged and in fact will be a pointer to user
memory. This causes `do_cmd_ioctl()` to `goto cleanup` and call
`do_become_nonbusy()` which would attempt to free the memory pointed to
by the user-space pointer. Fix it by setting `cmd->chanlist` to NULL at
the start of `__comedi_get_user_chanlist()`.
Fixes: c6cd0eefb27b ("staging: comedi: comedi_fops: introduce __comedi_get_user_chanlist()")
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y: 6cab7a37f5c04
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulation of code that is 14 bytes to the segment limit or closer
(e.g. RIP = 0xFFFFFFF2 after reset) is broken because we try to read as
many as 15 bytes from the beginning of the instruction, and __linearize
fails when the passed (address, size) pair reaches out of the segment.
To fix this, let __linearize return the maximum accessible size (clamped
to 2^32-1) for usage in __do_insn_fetch_bytes, and avoid the limit check
by passing zero for the desired size.
For expand-down segments, __linearize is performing a redundant check.
(u32)(addr.ea + size - 1) <= lim can only happen if addr.ea is close
to 4GB; in this case, addr.ea + size - 1 will also fail the check against
the upper bound of the segment (which is provided by the D/B bit).
After eliminating the redundant check, it is simple to compute
the *max_size for expand-down segments too.
Now that the limit check is done in __do_insn_fetch_bytes, we want
to inject a general protection fault there if size < op_size (like
__linearize would have done), instead of just aborting.
This fixes booting Tiano Core from emulated flash with EPT disabled.
Cc: stable@vger.kernel.org
Fixes: 719d5a9b2487e0562f178f61e323c3dc18a8b200
Reported-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- a few compilation fixes with randconfigs
- one potential compilation breakage on userspace due to the usage of
a gcc extension
- several warnings fixed
- some other random driver fixes"
* tag 'media/v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (22 commits)
[media] s5p-jpeg: Avoid -Wuninitialized warning in s5p_jpeg_parse_hdr
[media] s5p-fimc: Only build suspend/resume for PM
[media] s5p-jpeg: Only build suspend/resume for PM
[media] Remove references to non-existent PLAT_S5P symbol
[media] videobuf-dma-contig: set vm_pgoff to be zero to pass the sanity check in vm_iomap_memory()
[media] tw68: remove bogus I2C_ALGOBIT dependency
[media] usbvision-video: two use after frees
[media] tw68: remove deprecated IRQF_DISABLED
[media] xc5000: use after free in release()
[media] em28xx-input: NULL dereference on error
[media] wl128x: fix fmdbg compiler warning
Revert "[media] v4l2-dv-timings: fix a sparse warning"
[media] hackrf: harmless off by one in debug code
[media] cx23885: initialize config structs for T9580
[media] v4l: uvcvideo: Fix buffer completion size check
[media] vivid: fix buffer overrun
[media] saa7146: Create a device name before it's used
[media] em28xx: fix uninitialized variable warning
[media] vivid: fix Kconfig FB dependency
[media] anysee: make sure loading modules is const
...
commit c675949ec58ca50d5a3ae3c757892f1560f6e896
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
prevents backlight setup on Macbook 2,1. Apply quirk to ignore the VBT
check so backlight is set up properly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81438
Signed-off-by: Jens Stein Jørgensen <jens.s.stein@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks