Pull tracing fix from Steven Rostedt:
"A regression showed up that there's a large delay when enabling all
events. This was prevalent when FTRACE_SELFTEST was enabled which
enables all events several times, and caused the system bootup to
pause for over a minute.

This was tracked down to an addition of a synchronize_sched()
performed when system call tracepoints are unregistered.

The synchronize_sched() is needed between the unregistering of the
system call tracepoint and a deletion of a tracing instance buffer.
But placing the synchronize_sched() in the unreg of *every* system
call tracepoint is a bit overboard. A single synchronize_sched()
before the deletion of the instance is sufficient"

* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Only run synchronize_sched() at instance deletion time

Pull aio fix from Benjamin LaHaise:
"AIO fix from Gu Zheng that fixes a GPF that Dave Jones uncovered with
trinity"

* git://git.kvack.org/~bcrl/aio-next:
aio: clean up aio ring in the fail path

It has been reported that boot up with FTRACE_SELFTEST enabled can take a
very long time. There can be stalls of over a minute.

This was tracked down to the synchronize_sched() called when a system call
event is disabled. As the self tests enable and disable thousands of events,
this makes the synchronize_sched() get called thousands of times.

The synchornize_sched() was added with d562aff93bfb53 "tracing: Add support
for SOFT_DISABLE to syscall events" which caused this regression (added
in 3.13-rc1).

The synchronize_sched() is to protect against the events being accessed
when a tracer instance is being deleted. When an instance is being deleted
all the events associated to it are unregistered. The synchronize_sched()
makes sure that no more users are running when it finishes.

Instead of calling synchronize_sched() for all syscall events, we only
need to call it once, after the events are unregistered and before the
instance is deleted. The event_mutex is held during this action to
prevent new users from enabling events.

Link: http://lkml.kernel.org/r/20131203124120.427b9661@gandalf.local.home

Reported-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Acked-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Pull SCSI fixes from James Bottomley:
"This is a set of nine fixes (and one author update).

The libsas one should fix discovery in eSATA devices, the WRITE_SAME
one is the largest, but it should fix a lot of problems we've been
getting with the emulated RAID devices (they've been effectively lying
about support and then firmware has been choking on the commands).

The rest are various crash, hang or warn driver fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bfa: Fix crash when symb name set for offline vport
[SCSI] enclosure: fix WARN_ON in dual path device removing
[SCSI] pm80xx: Tasklets synchronization fix.
[SCSI] pm80xx: Resetting the phy state.
[SCSI] pm80xx: Fix for direct attached device.
[SCSI] pm80xx: Module author addition
[SCSI] hpsa: return 0 from driver probe function on success, not 1
[SCSI] hpsa: do not discard scsi status on aborted commands
[SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
[SCSI] libsas: fix usage of ata_tf_to_fis

Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898

Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

Pull IMA fixes from James Morris:
"Here are two more fixes for IMA"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: properly free ima_template_entry structures
ima: Do not free 'entry' before it is initialized

This patch fixes a crash when tried setting symbolic name for an offline
vport through sysfs. Crash is due to uninitialized pointer lport->ns,
which gets initialized only on linkup (port online).

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

After freeing ring_pages we leave it as is causing a dangling pointer. This
has already caused an issue so to help catching any issues in the future
NULL it out.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

Pull ARM64 fixes from Catalin Marinas:
- Remove preempt_count modifications in the arm64 IRQ handling code
since that's already dealt with in generic irq_enter/irq_exit
- PTE_PROT_NONE bit moved higher up to avoid overlapping with the
hardware bits (for PROT_NONE mappings which are pte_present)
- Big-endian fixes for ptrace support
- Asynchronous aborts unmasking while in the kernel
- pgprot_writecombine() change to create Normal NonCacheable memory
rather than Device GRE

* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Move PTE_PROT_NONE higher up
arm64: Use Normal NonCacheable memory for writecombine
arm64: debug: make aarch32 bkpt checking endian clean
arm64: ptrace: fix compat registes get/set to be endian clean
arm64: Unmask asynchronous aborts when in kernel mode
arm64: dts: Reserve the memory used for secondary CPU release address
arm64: let the core code deal with preempt_count

Pull devicetree fixes from Rob Herring:
- Various DT binding documentation updates
- Add Kumar Gala and remove Stephen Warren as DT binding maintainers

* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt: binding: reword PowerPC 8xxx GPIO documentation
ARM: tegra: delete nvidia,tegra20-spi.txt binding
hwmon: ntc_thermistor: Fix typo (pullup-uV -> pullup-uv)
of: add vendor prefix for GMT
clk: exynos: Fix typos in DT bindings documentation
of: Add vendor prefix for LG Corporation
Documentation: net: fsl-fec.txt: Add phy-supply entry
ARM: dts: doc: Document missing binding for omap5-mpu
dt-bindings: add ARMv8 PMU binding
MAINTAINERS: remove swarren from DT bindings
MAINTAINERS: Add Kumar to Device Tree Binding maintainers group

Bug report from: wenxiong@linux.vnet.ibm.com

The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.

enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.

For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.

Tested-by: wenxiong@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

ioctx_alloc() calls aio_setup_ring() to allocate a ring. If aio_setup_ring()
fails to do so it would call aio_free_ring() before returning, but
ioctx_alloc() would call aio_free_ring() again causing a double free of
the ring.

This is easily reproducible from userspace.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

Pull s390 updates from Martin Schwidefsky:
"One performance improvement and a few bug fixes. Two of the fixes
deal with the clock related problems we have seen on recent kernels"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: handle asce-type exceptions as normal page fault
s390,time: revert direct ktime path for s390 clockevent device
s390/time,vdso: convert to the new update_vsyscall interface
s390/uaccess: add missing page table walk range check
s390/mm: optimize copy_page
s390/dasd: validate request size before building CCW/TCW request
s390/signal: always restore saved runtime instrumentation psw bit

PTE_PROT_NONE means that a pte is present but does not have any
read/write attributes. However, setting the memory type like
pgprot_writecombine() is allowed and such bits overlap with
PTE_PROT_NONE. This causes mmap/munmap issues in drivers that change the
vma->vm_pg_prot on PROT_NONE mappings.

This patch reverts the PTE_FILE/PTE_PROT_NONE shift in commit
59911ca4325d (ARM64: mm: Move PTE_PROT_NONE bit) and moves PTE_PROT_NONE
together with the other software bits.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Cc: <stable@vger.kernel.org> # 3.11+

Pull power management fixes from Rafael Wysocki:

- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to avoid
garbage sysfs files from being left behind in case of a suspend error

- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.

- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled from
the kernel command line. From Konrad Rzeszutek Wilk.

- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.

- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.

- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.

- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.

* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PowerCap: Fix mode for energy counter
PNP: fix restoring devices after hibernation
cpuidle: Check for dev before deregistering it.
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
intel_idle: Fixed C6 state on Avoton/Rangeley processors

re-format and re-word the device tree binding documentation for MPC8xxx
and compatibles, reference the common document for interrupt controllers
and remove outdated duplicate SoC specific information

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <Pawel.Moll@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <devicetree@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

The new templates management mechanism records information associated
to an event into an array of 'ima_field_data' structures and makes it
available through the 'template_data' field of the 'ima_template_entry'
structure (the element of the measurements list created by IMA).

Since 'ima_field_data' contains dynamically allocated data (which length
varies depending on the data associated to a selected template field),
it is not enough to just free the memory reserved for a
'ima_template_entry' structure if something goes wrong.

This patch creates the new function ima_free_template_entry() which
walks the array of 'ima_field_data' structures, frees the memory
referenced by the 'data' pointer and finally the space reserved for
the 'ima_template_entry' structure. Further, it replaces existing kfree()
that have a pointer to an 'ima_template_entry' structure as argument
with calls to the new function.

Fixes: a71dc65: ima: switch to new template management mechanism
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>

When multiple vectors are used, the vector variable is over written,
resulting in unhandled operation for those vectors.
This fix prevents the problem by maitaining HBA instance and
vector values for each irq.

[jejb: checkpatch fixes]
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix

Git commit 9e34f2686bb088b211b6cac8772e1f644c6180f8
"s390/mm,tlb: tlb flush on page table upgrade fixup" removed the
exception handler for the asce-type exception. This is incorrect
as the user-copy with MVCOS can cause asce-type exceptions in
the kernel if a user pointer is too large. Those need to be
handled with do_no_context to branch to the fixup in the
user-copy code.

The simplest fix for this problem is to call do_dat_exception for
asce-type excpetions, as there is no vma for the address the code
will handle the exception correctly.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

This provides better performance compared to Device GRE and also allows
unaligned accesses. Such memory is intended to be used with standard RAM
(e.g. framebuffers) and not I/O.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull arch/tile ftrace bug fix from Chris Metcalf:
"This fixes a build failure with allyesconfig reported by Fengguang Wu
and fixed by Tony Lu"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
ftrace: default to tilegx if ARCH=tile is specified

* pm-epoll:
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled

* pnp:
PNP: fix restoring devices after hibernation

* powercap:
PowerCap: Fix mode for energy counter

This binding shouldn't exist; Tegra20 has two forms of SPI controller
that are documented separately in nvidia,tegra20-sflash.txt and
nvidia,tegra20-slink.txt.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

7bc5f447ce9d0 (ima: define new function ima_alloc_init_template() to
API) moved the initialization of 'entry' in ima_add_boot_aggregate() a
bit more below, after the if (ima_used_chip).

So, 'entry' is not initialized while being inside this if-block. So, we
should not attempt to free it.

Found by Coverity (CID: 1131971)

Fixes: 7bc5f447ce9d0 (ima: define new function ima_alloc_init_template() to API)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>

Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.

Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull networking fixes from David Miller:
"I'm sending a pull request of these lingering bug fixes for networking
before the normal merge window material because some of this stuff I'd
like to get to -stable ASAP"

1) cxgb3 stopped working on 32-bit machines, fix from Ben Hutchings.

2) Structures passed via netlink for netfilter logging are not fully
initialized. From Mathias Krause.

3) Properly unlink upper openvswitch device during notifications, from
Alexei Starovoitov.

4) Fix race conditions involving access to the IP compression scratch
buffer, from Michal Kubrecek.

5) We don't handle the expiration of MTU information contained in ipv6
routes sometimes, fix from Hannes Frederic Sowa.

6) With Fast Open we can miscompute the TCP SYN/ACK RTT, from Yuchung
Cheng.

7) Don't take TCP RTT sample when an ACK doesn't acknowledge new data,
also from Yuchung Cheng.

8) The decreased IPSEC garbage collection threshold causes problems for
some people, bump it back up. From Steffen Klassert.

9) Fix skb->truesize calculated by tcp_tso_segment(), from Eric
Dumazet.

10) flow_dissector doesn't validate packet lengths sufficiently, from
Jason Wang

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net/mlx4_core: Fix call to __mlx4_unregister_mac
net: sctp: do not trigger BUG_ON in sctp_cmd_delete_tcb
net: flow_dissector: fail on evil iph->ihl
xfrm: Fix null pointer dereference when decoding sessions
can: kvaser_usb: fix usb endpoints detection
can: c_can: Fix RX message handling, handle lost message before EOB
doc:net: Fix typo in Documentation/networking
bgmac: don't update slot on skb alloc/dma mapping error
ibm emac: Fix locking for enable/disable eob irq
ibm emac: Don't call napi_complete if napi_reschedule failed
virtio-net: correctly handle cpu hotplug notifier during resuming
bridge: pass correct vlan id to multicast code
net: x25: Fix dead URLs in Kconfig
netfilter: xt_NFQUEUE: fix --queue-bypass regression
xen-netback: use jiffies_64 value to calculate credit timeout
cxgb3: Fix length calculation in write_ofld_wr() on 32-bit architectures
bnx2x: Disable VF access on PF removal
bnx2x: prevent FW assert on low mem during unload
tcp: gso: fix truesize tracking
xfrm: Increase the garbage collector threshold
...

aio kiocb refcounting was broken - it was relying on keeping track of
the number of available ring buffer entries, which it needs to do
anyways; then at shutdown time it'd wait for completions to be delivered
until the # of available ring buffer entries equalled what it was
initialized to.

Problem with that is that the ring buffer is mapped writable into
userspace, so userspace could futz with the head and tail pointers to
cause the kernel to see extra completions, and cause free_ioctx() to
return while there were still outstanding kiocbs. Which would be bad.

Fix is just to directly refcount the kiocbs - which is more
straightforward, and with the new percpu refcounting code doesn't cost
us any cacheline bouncing which was the whole point of the original
scheme.

Also clean up ioctx_alloc()'s error path and fix a bug where it wasn't
subtracting from aio_nr if ioctx_add_table() failed.

Signed-off-by: Kent Overstreet <kmo@daterainc.com>

Pull workqueue fixes from Tejun Heo:
"This contains one important fix. The NUMA support added a while back
broke ordering guarantees on ordered workqueues. It was enforced by
having single frontend interface with @max_active == 1 but the NUMA
support puts multiple interfaces on unbound workqueues on NUMA
machines thus breaking the ordered guarantee. This is fixed by
disabling NUMA support on ordered workqueues.

The above and a couple other patches were sitting in for-3.12-fixes
but I forgot to push that out, so they ended up waiting a bit too
long. My aplogies.

Other fixes are minor"

* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix pool ID allocation leakage and remove BUILD_BUG_ON() in init_workqueues
workqueue: fix comment typo for __queue_work()
workqueue: fix ordered workqueues in NUMA setups
workqueue: swap set_cpus_allowed_ptr() and PF_NO_SETAFFINITY

In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.

Signed-off-by: Florian Meier <florian.meier@koalo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Git commit 4f37a68cdaf6dea833cfdded2a3e0c47c0f006da
"s390: Use direct ktime path for s390 clockevent device" makes use
of the CLOCK_EVT_FEAT_KTIME clockevent option to avoid the delta
calculation with ktime_get() in clockevents_program_event and the
get_tod_clock() in s390_next_event. This is based on the assumption
that the difference between the internal ktime and the hardware
clock is reflected in the wall_to_monotonic delta. But this is not
true, the ntp corrections are applied via changes to the tk->mult
multiplier and this is not reflected in wall_to_monotonic.

In theory this could be solved by using the raw monotonic clock
but it is simpler to switch back to the standard clock delta
calculation.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The current breakpoint instruction checking code for A32 is not endian
clean. Fix this with appropriate byte-swapping when retrieving
instructions.

Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. It contains:

- A fix for a use-after-free of a request in blk-mq. From Ming Lei

- A fix for a blk-mq bug that could attempt to dereference a NULL rq
if allocation failed

- Two xen-blkfront small fixes

- Cleanup of submit_bio_wait() type uses in the kernel, unifying
that. From Kent

- A fix for 32-bit blkg_rwstat reading. I apologize for this one
looking mangled in the shortlog, it's entirely my fault for missing
an empty line between the description and body of the text"

* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix use-after-free of request
blk-mq: fix dereference of rq->mq_ctx if allocation fails
block: xen-blkfront: Fix possible NULL ptr dereference
xen-blkfront: Silence pfn maybe-uninitialized warning
block: submit_bio_wait() conversions
Update of blkg_stat and blkg_rwstat may happen in bh context

This matches the existing behavior in arch/tile/Makefile for defconfig.

Reported-by: fengguang.wu@intel.com
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Tony Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors

* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate

Drop EPOLLWAKEUP from epoll events mask if CONFIG_PM_SLEEP is disabled.

Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

On returning from hibernation 'restore' callback is called,
not 'resume'. Fix it.

Fixes: eaf140b60ec9 (PNP: convert PNP driver bus legacy pm_ops to dev_pm_ops)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

As per the documentation of powercap sysfs, energy_uj field is read only,
if it can't be reset. Currently it always allows write but will fail,
if there is no reset callback.
Changing mode field, to read only if there is no reset callback.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch fix typo of property name from 'pullup-uV' to 'pullup-uv'.
The ntc_thermistor.c use 'pullup-uv' when parsing dt data.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition

In case of direct attached SATA device delay is not enough.
It will give crash for set device state command response and
wait_for_completion is the best solution for this.

Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

In function mlx4_master_deactivate_admin_state() __mlx4_unregister_mac was
called using the MAC index. It should be called with the value of the MAC itself.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libata fixes from Tejun Heo:
"libata device removal path was removing parent device node before its
child, which is mostly harmless but triggers warning after recent
sysfs changes. Rafael's patch fixes the order.

Other than that, minor controller-specific fixes and device ID
additions"

* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ATA: Fix port removal ordering
ahci: add Marvell 9230 to the AHCI PCI device list
ata: fix acpi_bus_get_device() return value check
pata_arasan_cf: add missing clk_disable_unprepare() on error path
ahci: add support for IBM Akebono platform device

When one work starts execution, the high bits of work's data contain
pool ID. It can represent a maximum of WORK_OFFQ_POOL_NONE. Pool ID
is assigned WORK_OFFQ_POOL_NONE when the work being initialized
indicating that no pool is associated and get_work_pool() uses it to
check the associated pool. So if worker_pool_assign_id() assigns a
ID greater than or equal WORK_OFFQ_POOL_NONE to a pool, it triggers
leakage, and it may break the non-reentrance guarantee.

This patch fix this issue by modifying the worker_pool_assign_id()
function calling idr_alloc() by setting @end param WORK_OFFQ_POOL_NONE.

Furthermore, in the current implementation, the BUILD_BUG_ON() in
init_workqueues makes no sense. The number of worker pools needed
cannot be determined at compile time, because the number of backing
pools for UNBOUND workqueues is dynamic based on the assigned custom
attributes. So remove it.

tj: Minor comment and indentation updates.

Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.

Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Switch to the improved update_vsyscall interface that provides
sub-nanosecond precision for gettimeofday and clock_gettime.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

On a BE system the wrong half of the X registers is retrieved/written
when attempting to get/set the value of aarch32 registers through
ptrace.

Ensure that types are the correct width so that the relevant
casting occurs.

Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning
delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond
Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings

* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix do_div() warning by instead using sector_div()
MAINTAINERS: Update contact information for Trond Myklebust
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
SUNRPC: do not fail gss proc NULL calls with EACCES
NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
NFSv4: Update list of irrecoverable errors on DELEGRETURN
NFSv4 wait on recovery for async session errors
NFS: Fix a warning in nfs_setsecurity
NFS: Enabling v4.2 should not recompile nfsd and lockd

If accounting is on, we will do the IO completion accounting after
we have freed the request. Fix that by moving it sooner instead.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

If not, we could end up in the unfortunate situation where
we dereference a NULL pointer b/c we have cpuidle disabled.

This is the case when booting under Xen (which uses the
ACPI P/C states but disables the CPU idle driver) - and can
be easily reproduced when booting with cpuidle.off=1.

BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8156db4a>] cpuidle_unregister_device+0x2a/0x90
.. snip..
Call Trace:
[<ffffffff813b15b4>] acpi_processor_power_exit+0x3c/0x5c
[<ffffffff813af0a9>] acpi_processor_stop+0x61/0xb6
[<ffffffff814215bf>] __device_release_driver+0fffff81421653>] device_release_driver+0x23/0x30
[<ffffffff81420ed8>] bus_remove_device+0x108/0x180
[<ffffffff8141d9d9>] device_del+0x129/0x1c0
[<ffffffff813cb4b0>] ? unregister_xenbus_watch+0x1f0/0x1f0
[<ffffffff8141da8e>] device_unregister+0x1e/0x60
[<ffffffff814243e9>] unregister_cpu+0x39/0x60
[<ffffffff81019e03>] arch_unregister_cpu+0x23/0x30
[<ffffffff813c3c51>] handle_vcpu_hotplug_event+0xc1/0xe0
[<ffffffff813cb4f5>] xenwatch_thread+0x45/0x120
[<ffffffff810af010>] ? abort_exclusive_wait+0xb0/0xb0
[<ffffffff8108ec42>] kthread+0xd2/0xf0
[<ffffffff8108eb70>] ? kthread_create_on_node+0x180/0x180
[<ffffffff816ce17c>] ret_from_fork+0x7c/0xb0
[<ffffffff8108eb70>] ? kthread_create_on_node+0x180/0x180

This problem also appears in 3.12 and could be a candidate for backport.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This is effectively a revert of commit 5302c3fb2e62 ("cpufreq: Perform
light-weight init/teardown during suspend/resume"), which enabled
suspend/resume optimizations leaving the sysfs files in place.

Errors during suspend/resume are not handled properly, leaving
dead sysfs attributes in case of failures. There are are number of
functions with special code for the "frozen" case, and all these
need to also have special error handling.

The problem is easy to demonstrate by making cpufreq_driver->init()
or cpufreq_driver->get() fail during resume.

The code is too complex for a simple fix, with split code paths
in multiple blocks within a number of functions. It is therefore
best to revert the patch enabling this code until the error handling
is in place.

Examples of problems resulting from resume errors:

WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b

The failure to restore cpufreq devices on cancelled hibernation is
not a new bug. It is caused by the ACPI _PPC call failing unless the
hibernate is completed. This makes the acpi_cpufreq driver fail its
init.

Previously, the cpufreq device could be restored by offlining the
cpu temporarily. And as a complete hibernation cycle would do this,
it would be automatically restored most of the time. But after
commit 5302c3fb2e62 the leftover sysfs attributes will block any
device add action. Therefore offlining and onlining CPU 1 will no
longer restore the cpufreq object, and a complete suspend/resume
cycle will replace it with garbage.

Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix compile error with gcc option: -Werror=format-security for
dev_set_name(&control_type->dev, name).

Changed to dev_set_name(&control_type->dev, "%s", name).

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Adding Global Mixed-mode Technology Inc. to the list
of devicetree vendor prefixes.

Signed-off-by: Wei Ni <wni@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>