tjh.dev
commits
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: sbp2: fix freeing of unallocated memory
firewire: ohci: fix Ricoh R5C832, video reception
firewire: ohci: fix Agere FW643 and multiple cameras
firewire: core: fix crash in iso resource management
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a target writes invalid status (typically status of a command that
already timed out), firewire-sbp2 attempts to put away an ORB that
doesn't exist. https://bugzilla.redhat.com/show_bug.cgi?id=519772
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/~dwmw2/mtd-2.6.31:
JFFS2: add missing verify buffer allocation/deallocation
mtd: nftl: fix offset alignments
mtd: nftl: write support is broken
mtd: m25p80: fix null pointer dereference bug
In dual-buffer DMA mode, no video frames are ever received from R5C832
by libdc1394. Fallback to packet-per-buffer DMA works reliably.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/13393/focus=13476
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Allow changing max_sectors_kb above the default 512
The function jffs2_nor_wbuf_flash_setup() doesn't allocate the verify buffer
if CONFIG_JFFS2_FS_WBUF_VERIFY is defined, so causing a kernel panic when
that macro is enabled and the verify function is called. Similarly the
jffs2_nor_wbuf_flash_cleanup() must free the buffer if
CONFIG_JFFS2_FS_WBUF_VERIFY is enabled.
The following patch fixes the problem.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
An Agere FW643 OHCI 1.1 card works fine for video reception from one
camera but fails early if receiving from two cameras. After a short
while, no IR IRQ events occur and the context control register does not
react anymore. This happens regardless whether both IR DMA contexts are
dual-buffer or one is dual-buffer and the other packet-per-buffer.
This can be worked around by disabling dual buffer DMA mode entirely.
http://sourceforge.net/mailarchive/message.php?msg_name=4A7C0594.2020208%40gmail.com
(Reported by Samuel Audet.)
In another report (by Jonathan Cameron), an FW643 works OK with two
cameras in dual buffer mode. Whether this is due to different chip
revisions or different usage patterns (different video formats) is not
yet clear. However, as far as the current capabilities of
firewire-core's isochronous I/O interface are concerned, simply
switching off dual-buffer on non-working and working FW643s alike is not
a problem in practice. We only need to revisit this issue if we are
going to enhance the interface, e.g. so that applications can explicitly
choose modes.
Reported-by: Samuel Audet <samuel.audet@gmail.com>
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'fix/oxygen' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oxygen: handle cards with missing EEPROM
sound: oxygen: fix MCLK rate for 192 kHz playback
The patch "block: Use accessor functions for queue limits"
(ae03bf639a5027d27270123f5f6e3ee6a412781d) changed queue_max_sectors_store()
to use blk_queue_max_sectors() instead of directly assigning the value.
But blk_queue_max_sectors() differs a bit
1. It sets both max_sectors_kb, and max_hw_sectors_kb
2. Never allows one to change max_sectors_kb above BLK_DEF_MAX_SECTORS. If one
specifies a value greater then max_hw_sectors is set to that value but
max_sectors is set to BLK_DEF_MAX_SECTORS
I am not sure whether blk_queue_max_sectors() should be changed, as it seems
to be that way for a long time. And there may be callers dependent on that
behaviour.
This patch simply reverts to the older way of directly assigning the value to
max_sectors as it was before.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Arithmetic conversion in the mask computation makes the upper word
of the second argument passed down to mtd->read_oob(), be always 0
(assuming 'offs' being a 64-bit signed long long type, and
'mtd->writesize' being a 32-bit unsigned int type).
This patch applies over the other one adding masking in nftl_write,
"nftl: write support is broken".
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a regression due to post 2.6.30 commit "firewire: core: do
not DMA-map stack addresses" 6fdc03709433ccc2005f0f593ae9d9dd04f7b485.
As David Moore noted, a previously correct sizeof() expression became
wrong since the commit changed its argument from an array to a pointer.
This resulted in an oops in ohci_cancel_packet in the shared workqueue
thread's context when an isochronous resource was to be freed.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tc: Fix unitialized kernel memory leak
pkt_sched: Revert tasklet_hrtimer changes.
net: sk_free() should be allowed right after sk_alloc()
gianfar: gfar_remove needs to call unregister_netdev()
ipw2200: firmware DMA loading rework
The card model detection code introduced in 2.6.30 that tries to work
around partially broken EEPROM contents by reading the EEPROM directly
does not handle cards where the EEPROM has been omitted. In this case,
we have to use the default ID to allow the driver to load.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: don't free non-existent backlight in acpi video module
toshiba_acpi: return on a fail path
ACPICA: Windows compatibility fix: same buffer/string store
Write support is broken in NFTL. Fix it.
Signed-off-by: <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Fix skcipher_dequeue_givcrypt NULL test
Three bytes of uninitialized kernel memory are currently leaked to user
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not forget to program the MCLK ratio for the I2S output.
Otherwise, the master clock frequency can be too high for
the DACs at sample frequencies above 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: update the group mask on mark addition
inotify: fix length reporting and size checking
inotify: do not send a block of zeros when no pathname is available
acpi_video_put_one_device was attempting to remove sysfs entries and
unregister a backlight device without first checking that said backlight
device structure had been created.
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the following oops, observed with MTD_PARTITIONS=n:
m25p80 spi32766.0: m25p80 (1024 Kbytes)
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xc03a54b0
Oops: Kernel access of bad area, sig: 11 [#1]
Modules linked in:
NIP: c03a54b0 LR: c03a5494 CTR: c01e98b8
REGS: ef82bb60 TRAP: 0300 Not tainted (2.6.31-rc4-00167-g4733fd3)
MSR: 00029000 <EE,ME,CE> CR: 24022022 XER: 20000000
DEAR: 00000008, ESR: 00000000
TASK = ef82c000[1] 'swapper' THREAD: ef82a000
GPR00: 00000000 ef82bc10 ef82c000 0000002e 00001eb8 ffffffff c01e9824 00000036
GPR08: c054ed40 c0542a08 00001eb8 00004000 22022022 1001a1a0 3ff8fd00 00000000
GPR16: 00000000 00000001 00000000 00000000 ef82bddc c0530000 efbef500 ef8356d0
GPR24: 00000000 ef8356d0 00000000 efbf7a00 c0530ec4 ffffffed efbf5300 c0541f98
NIP [c03a54b0] m25p_probe+0x22c/0x354
LR [c03a5494] m25p_probe+0x210/0x354
Call Trace:
[ef82bc10] [c03a5494] m25p_probe+0x210/0x354 (unreliable)
[ef82bca0] [c024e37c] spi_drv_probe+0x2c/0x3c
[ef82bcb0] [c01f1afc] driver_probe_device+0xa4/0x178
[ef82bcd0] [c01f06e8] bus_for_each_drv+0x6c/0xa8
[ef82bd00] [c01f1a34] device_attach+0x84/0xa8
...
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Re-enable cpufreq suspend and resume code
As struct skcipher_givcrypt_request includes struct crypto_request
at a non-zero offset, testing for NULL after converting the pointer
returned by crypto_dequeue_request does not work. This can result
in IPsec crashes when the queue is depleted.
This patch fixes it by doing the pointer conversion only when the
return value is non-NULL. In particular, we create a new function
__crypto_dequeue_request that does the pointer conversion.
Reported-by: Brad Bosch <bradbosch@comcast.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd470d7a64255a10b843b0d188416b78f
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d7983632100a9ff3fd20295f6e34074a8
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea17759e1ce5503bdae2b07e48e32af9
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Aug 18, 2009 at 01:45:17PM -0400, John David Anglin wrote:
> CC arch/parisc/kernel/traps.o
> arch/parisc/kernel/traps.c: In function 'handle_interruption':
> arch/parisc/kernel/traps.c:535:18: warning: operation on 'regs->iasq[0]'
> may be undefined
Yes - Line 535 should use both [0] and [1].
Reported-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seperating the addition and update of marks in inotify resulted in a
regression in that inotify never gets events. The inotify group mask is
always 0. This mask should be updated any time a new mark is added.
Signed-off-by: Eric Paris <eparis@redhat.com>
Return from bt_rfkill_poll() when hci_get_radio_state() fails.
value is invalid in that case and should not be assigned to the rfkill
state.
This also fixes a double unlock bug.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
In the recent change by Al Viro that changes verious subsystems
to use "struct path" one case was missed in the autofs4 module
which causes mounts to no longer expire.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firewire-core (payload of lock requests in the bus
manager work and in iso resource management) to slab-allocated memory.
There are a number on-stack buffers for quadlet write or quadlet read
requests in firewire-core and firewire-sbp2. These are harmless; they
are copied to/ from card driver internal DMA buffers since quadlet
payloads are inlined with packet headers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix csum_ipv6_magic()
[IA64] Fix warning in dma-mapping.c
Commit 4bc5d3413503 is broken and causes regressions:
(1) cpufreq_driver->resume() and ->suspend() were only called on
__powerpc__, but you could set them on all architectures. In fact,
->resume() was defined and used before the PPC-related commit
42d4dc3f4e1e complained about in 4bc5d3413503.
(2) Therfore, the resume functions in acpi_cpufreq and speedstep-smi
would never be called.
(3) This means speedstep-smi would be unusuable after suspend or resume.
The _real_ problem was calling cpufreq_driver->get() with interrupts
off, but it re-enabling interrupts on some platforms. Why is ->get()
necessary?
Some systems like to change the CPU frequency behind our
back, especially during BIOS-intensive operations like suspend or
resume. If such systems also use a CPU frequency-dependant timing loop,
delays might be off by large factors. Therefore, we need to ascertain
as soon as possible that the CPU frequency is indeed at the speed we
think it is. You can do this two ways: either setting it anew, or trying
to get it. The latter is what was done, the former also has the same IRQ
issue.
So, let's try something different: defer the checking to after interrupts
are re-enabled, by calling cpufreq_update_policy() (via schedule_work()).
Timings may be off until this later stage, so let's watch out for
resume regressions caused by the deferred handling of frequency changes
behind the kernel's back.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
kernel_fpu_begin/end used preempt_disable/enable, so sleep should be
prevented between kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After commit 2b85a34e911bf483c27cfdd124aeb1605145dc80
(net: No more expensive sock_hold()/sock_put() on each tx)
sk_free() frees socks conditionally and depends
on sk_wmem_alloc being set e.g. in sock_init_data(). But in some
cases sk_free() is called earlier, usually after other alloc errors.
Fix is to move sk_wmem_alloc initialization from sock_init_data()
to sk_alloc() itself.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]
However, there's a problem with commit
6d76013381ed28979cd122eb4b249a88b5e384fa in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()
This should fix it
[ This patch leaves other problems, particularly the sections directory,
but recent parisc toolchains seem to produce these modules and this
prevents a crash and is a minimal change -- RR ]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the bug that was reported in
http://bugzilla.kernel.org/show_bug.cgi?id=14053
If we're in the case where we need to force a reencode and then resend of
the RPC request, due to xprt_transmit failing with a networking error, then
we _must_ retransmit the entire request.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
0db501bd0610ee0c0 introduced a regresion in that it now sends a nul
terminator but the length accounting when checking for space or
reporting to userspace did not take this into account. This corrects
all of the rounding logic.
Signed-off-by: Eric Paris <eparis@redhat.com>
Fix a compatibility issue when the same buffer or string is
stored to itself. This has been seen in the field. Previously,
ACPICA would zero out the buffer/string. Now, the operation is
treated as a NOP.
http://bugzilla.acpica.org/show_bug.cgi?id=803
Reported-by: Rezwanul Kabir <Rezwanul_Kabir@Dell.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix MacBookPro 3,1/4,1 quirk with ALC889A
ALSA: hda - Add missing mux check for VT1708
The new stack is now recommended over the old one if used for industrial
video (IIDC/DCAM) or for storage devices (SBP-2) due to better
performance, improved compatibility, added features, and security. It
should also be functionally on par with and is more secure than the old
ieee1394 stack in the use case of consumer video devices.
IP-over-1394 support for the new stack is currently emerging, and a
backend of the firedtv DVB driver to the new stack should be available
soon.
The one remaining area where the old stack is still required are audio
devices, as the new stack is not yet able to support the FFADO FireWire
audio framework.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: actually enable the swapext compat handler
The 32-bit parameters (len and csum) of csum_ipv6_magic() are passed in 64-bit
registers in2 and in4. The high order 32 bits of the registers were never
cleared, and garbage was sometimes calculated into the checksum.
Fix this by clearing the high order 32 bits of these registers.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because AES-NI instructions will touch XMM state, corresponding code
must be enclosed within kernel_fpu_begin/end, which used
preempt_disable/enable. So sleep should be prevented between
kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch solves the problem that the Oops(BUG_ON) occurs by rmmod.
# rmmod gianfar_driver
------------[ cut here ]------------
Kernel BUG at c01fec48 [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
MPC837x MDS
Modules linked in: gianfar_driver(-) usb_storage scsi_wait_scan
NIP: c01fec48 LR: c01febf4 CTR: c01feba8
REGS: dec5bd60 TRAP: 0700 Tainted: G W (2.6.31-rc2)
MSR: 00029032 <EE,ME,CE,IR,DR> CR: 22000424 XER: 20000000
TASK = dec4cac0[1135] 'rmmod' THREAD: dec5a000
GPR00: 00000002 dec5be10 dec4cac0 dfba1820 c035d444 c035d478 ffffffff 00000000
GPR08: 0000002b 00000001 dfba193c 00000001 22000424 10019b34 1ffcb000 00000000
GPR16: 10012008 00000000 bf82ebe0 100017ec bf82ebec bf82ebe8 bf82ebd0 00000880
GPR24: 00000000 bf82ebf0 c03532f0 c03532e4 c036b594 dfba183c dfba1800 dfba1820
NIP [c01fec48] free_netdev+0xa0/0xb8
LR [c01febf4] free_netdev+0x4c/0xb8
Call Trace:
[dec5be10] [c01febf4] free_netdev+0x4c/0xb8 (unreliable)
[dec5be30] [e105f290] gfar_remove+0x50/0x68 [gianfar_driver]
[dec5be40] [c01ec534] of_platform_device_remove+0x30/0x44
[dec5be50] [c0181760] __device_release_driver+0x68/0xc8
[dec5be60] [c0181868] driver_detach+0xa8/0xac
[dec5be80] [c0180814] bus_remove_driver+0x9c/0xd8
[dec5bea0] [c0181efc] driver_unregister+0x60/0x98
[dec5beb0] [c01ec650] of_unregister_driver+0x14/0x24
[dec5bec0] [e10631bc] gfar_exit+0x18/0x4bc [gianfar_driver]
[dec5bed0] [c0047584] sys_delete_module+0x16c/0x228
[dec5bf40] [c00116bc] ret_from_syscall+0x0/0x38
--- Exception: c01 at 0xff3669c
LR = 0x10000f34
Instruction dump:
409e0024 a07e00c0 7c63f050 4be74429 80010024 bba10014 38210020 7c0803a6
4e800020 68000003 3160ffff 7d2b0110 <0f090000> 38000004 387e01f0 901e01d4
---[ end trace 8c595bcd37230a0f ]---
localhost kernel: ------------[ cut here ]------------
Signed-off-by: Toru UCHIYAMA uchiyama.toru@jp.fujitsu.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The rarely-used symbol_put_addr() needs to use dereference_function_descriptor
on powerpc.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
> James Bottomley (1):
> module: workaround duplicate section names
-tip testing found that this patch breaks the build on x86 if
CONFIG_KALLSYMS is disabled:
kernel/module.c: In function ‘load_module’:
kernel/module.c:2367: error: ‘struct module’ has no member named ‘sect_attrs’
distcc[8269] ERROR: compile kernel/module.c on ph/32 failed
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel] Error 2
make: *** Waiting for unfinished jobs....
Commit 1b364bf misses the fact that section attributes are only
built and dealt with if kallsyms is enabled. The patch below fixes
this.
( note, technically speaking this should depend on CONFIG_SYSFS as
well but this patch is correct too and keeps the #ifdef less
intrusive - in the KALLSYMS && !SYSFS case the code is a NOP. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Replaced patch with a slightly cleaner variation by James Bottomley ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an event has no pathname, there's no need to pad it with a null byte and
therefore generate an inotify_event sized block of zeros. This fixes a
regression introduced by commit 0db501bd0610ee0c0aca84d927f90bcccd09e2bd where
my system wouldn't finish booting because some process was being confused by
this.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (12564a): MAINTAINERS: Update gspca sn9c20x name style
V4L/DVB (12502): gspca - sn9c20x: Fix gscpa sn9c20x build errors.
V4L/DVB (12495): em28xx: Don't call em28xx_ir_init when disable_ir is true
V4L/DVB (12457): zr364: wrong indexes
V4L/DVB (12451): Update KConfig File to enable SDIO and USB interfaces
V4L/DVB (12450): Siano: Fixed SDIO compilation bugs
V4L/DVB (12449): adds webcam for Micron device MT9M111 0x143A to em28xx
V4L/DVB (12446): sms1xxx: restore GPIO functionality for all Hauppauge devices
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Reference: kernel bug#14078
http://bugzilla.kernel.org/show_bug.cgi?id=14078
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The AR req handler should not check the generation; higher level code
is the better place to handle bus generation changes. The target node
ID just needs to be checked for not being the "all nodes" address; in
this case don't handle the request and don't respond.
Use Address_Error and Type_Error rcodes as appropriate.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix preempt count underflow in nilfs_btnode_prepare_change_key
Fix a small typo in the compat ioctl handler that cause the swapext
compat handler to never be called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
arch/ia64/kernel/dma-mapping.c:14: warning: control reaches end of non-void function
arch/ia64/kernel/dma-mapping.c:14: warning: no return statement in function returning non-void
This warning was introduced by commit: 390bd132b2831a2ad0268e84bffbfc0680debfe5
Add dma_debug_init() for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
Original implementation of aesni_cbc_dec do not save IV if input
length % 4 == 0. This will make decryption of next block failed.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.
Connect to the backend before registering our framebuffer with the kernel.
[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In dual-buffer DMA mode, no video frames are ever received from R5C832
by libdc1394. Fallback to packet-per-buffer DMA works reliably.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/13393/focus=13476
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The function jffs2_nor_wbuf_flash_setup() doesn't allocate the verify buffer
if CONFIG_JFFS2_FS_WBUF_VERIFY is defined, so causing a kernel panic when
that macro is enabled and the verify function is called. Similarly the
jffs2_nor_wbuf_flash_cleanup() must free the buffer if
CONFIG_JFFS2_FS_WBUF_VERIFY is enabled.
The following patch fixes the problem.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
An Agere FW643 OHCI 1.1 card works fine for video reception from one
camera but fails early if receiving from two cameras. After a short
while, no IR IRQ events occur and the context control register does not
react anymore. This happens regardless whether both IR DMA contexts are
dual-buffer or one is dual-buffer and the other packet-per-buffer.
This can be worked around by disabling dual buffer DMA mode entirely.
http://sourceforge.net/mailarchive/message.php?msg_name=4A7C0594.2020208%40gmail.com
(Reported by Samuel Audet.)
In another report (by Jonathan Cameron), an FW643 works OK with two
cameras in dual buffer mode. Whether this is due to different chip
revisions or different usage patterns (different video formats) is not
yet clear. However, as far as the current capabilities of
firewire-core's isochronous I/O interface are concerned, simply
switching off dual-buffer on non-working and working FW643s alike is not
a problem in practice. We only need to revisit this issue if we are
going to enhance the interface, e.g. so that applications can explicitly
choose modes.
Reported-by: Samuel Audet <samuel.audet@gmail.com>
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The patch "block: Use accessor functions for queue limits"
(ae03bf639a5027d27270123f5f6e3ee6a412781d) changed queue_max_sectors_store()
to use blk_queue_max_sectors() instead of directly assigning the value.
But blk_queue_max_sectors() differs a bit
1. It sets both max_sectors_kb, and max_hw_sectors_kb
2. Never allows one to change max_sectors_kb above BLK_DEF_MAX_SECTORS. If one
specifies a value greater then max_hw_sectors is set to that value but
max_sectors is set to BLK_DEF_MAX_SECTORS
I am not sure whether blk_queue_max_sectors() should be changed, as it seems
to be that way for a long time. And there may be callers dependent on that
behaviour.
This patch simply reverts to the older way of directly assigning the value to
max_sectors as it was before.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Arithmetic conversion in the mask computation makes the upper word
of the second argument passed down to mtd->read_oob(), be always 0
(assuming 'offs' being a 64-bit signed long long type, and
'mtd->writesize' being a 32-bit unsigned int type).
This patch applies over the other one adding masking in nftl_write,
"nftl: write support is broken".
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a regression due to post 2.6.30 commit "firewire: core: do
not DMA-map stack addresses" 6fdc03709433ccc2005f0f593ae9d9dd04f7b485.
As David Moore noted, a previously correct sizeof() expression became
wrong since the commit changed its argument from an array to a pointer.
This resulted in an oops in ohci_cancel_packet in the shared workqueue
thread's context when an isochronous resource was to be freed.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The card model detection code introduced in 2.6.30 that tries to work
around partially broken EEPROM contents by reading the EEPROM directly
does not handle cards where the EEPROM has been omitted. In this case,
we have to use the default ID to allow the driver to load.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
acpi_video_put_one_device was attempting to remove sysfs entries and
unregister a backlight device without first checking that said backlight
device structure had been created.
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the following oops, observed with MTD_PARTITIONS=n:
m25p80 spi32766.0: m25p80 (1024 Kbytes)
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xc03a54b0
Oops: Kernel access of bad area, sig: 11 [#1]
Modules linked in:
NIP: c03a54b0 LR: c03a5494 CTR: c01e98b8
REGS: ef82bb60 TRAP: 0300 Not tainted (2.6.31-rc4-00167-g4733fd3)
MSR: 00029000 <EE,ME,CE> CR: 24022022 XER: 20000000
DEAR: 00000008, ESR: 00000000
TASK = ef82c000[1] 'swapper' THREAD: ef82a000
GPR00: 00000000 ef82bc10 ef82c000 0000002e 00001eb8 ffffffff c01e9824 00000036
GPR08: c054ed40 c0542a08 00001eb8 00004000 22022022 1001a1a0 3ff8fd00 00000000
GPR16: 00000000 00000001 00000000 00000000 ef82bddc c0530000 efbef500 ef8356d0
GPR24: 00000000 ef8356d0 00000000 efbf7a00 c0530ec4 ffffffed efbf5300 c0541f98
NIP [c03a54b0] m25p_probe+0x22c/0x354
LR [c03a5494] m25p_probe+0x210/0x354
Call Trace:
[ef82bc10] [c03a5494] m25p_probe+0x210/0x354 (unreliable)
[ef82bca0] [c024e37c] spi_drv_probe+0x2c/0x3c
[ef82bcb0] [c01f1afc] driver_probe_device+0xa4/0x178
[ef82bcd0] [c01f06e8] bus_for_each_drv+0x6c/0xa8
[ef82bd00] [c01f1a34] device_attach+0x84/0xa8
...
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As struct skcipher_givcrypt_request includes struct crypto_request
at a non-zero offset, testing for NULL after converting the pointer
returned by crypto_dequeue_request does not work. This can result
in IPsec crashes when the queue is depleted.
This patch fixes it by doing the pointer conversion only when the
return value is non-NULL. In particular, we create a new function
__crypto_dequeue_request that does the pointer conversion.
Reported-by: Brad Bosch <bradbosch@comcast.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd470d7a64255a10b843b0d188416b78f
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d7983632100a9ff3fd20295f6e34074a8
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea17759e1ce5503bdae2b07e48e32af9
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Aug 18, 2009 at 01:45:17PM -0400, John David Anglin wrote:
> CC arch/parisc/kernel/traps.o
> arch/parisc/kernel/traps.c: In function 'handle_interruption':
> arch/parisc/kernel/traps.c:535:18: warning: operation on 'regs->iasq[0]'
> may be undefined
Yes - Line 535 should use both [0] and [1].
Reported-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return from bt_rfkill_poll() when hci_get_radio_state() fails.
value is invalid in that case and should not be assigned to the rfkill
state.
This also fixes a double unlock bug.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firewire-core (payload of lock requests in the bus
manager work and in iso resource management) to slab-allocated memory.
There are a number on-stack buffers for quadlet write or quadlet read
requests in firewire-core and firewire-sbp2. These are harmless; they
are copied to/ from card driver internal DMA buffers since quadlet
payloads are inlined with packet headers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit 4bc5d3413503 is broken and causes regressions:
(1) cpufreq_driver->resume() and ->suspend() were only called on
__powerpc__, but you could set them on all architectures. In fact,
->resume() was defined and used before the PPC-related commit
42d4dc3f4e1e complained about in 4bc5d3413503.
(2) Therfore, the resume functions in acpi_cpufreq and speedstep-smi
would never be called.
(3) This means speedstep-smi would be unusuable after suspend or resume.
The _real_ problem was calling cpufreq_driver->get() with interrupts
off, but it re-enabling interrupts on some platforms. Why is ->get()
necessary?
Some systems like to change the CPU frequency behind our
back, especially during BIOS-intensive operations like suspend or
resume. If such systems also use a CPU frequency-dependant timing loop,
delays might be off by large factors. Therefore, we need to ascertain
as soon as possible that the CPU frequency is indeed at the speed we
think it is. You can do this two ways: either setting it anew, or trying
to get it. The latter is what was done, the former also has the same IRQ
issue.
So, let's try something different: defer the checking to after interrupts
are re-enabled, by calling cpufreq_update_policy() (via schedule_work()).
Timings may be off until this later stage, so let's watch out for
resume regressions caused by the deferred handling of frequency changes
behind the kernel's back.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
After commit 2b85a34e911bf483c27cfdd124aeb1605145dc80
(net: No more expensive sock_hold()/sock_put() on each tx)
sk_free() frees socks conditionally and depends
on sk_wmem_alloc being set e.g. in sock_init_data(). But in some
cases sk_free() is called earlier, usually after other alloc errors.
Fix is to move sk_wmem_alloc initialization from sock_init_data()
to sk_alloc() itself.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]
However, there's a problem with commit
6d76013381ed28979cd122eb4b249a88b5e384fa in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()
This should fix it
[ This patch leaves other problems, particularly the sections directory,
but recent parisc toolchains seem to produce these modules and this
prevents a crash and is a minimal change -- RR ]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the bug that was reported in
http://bugzilla.kernel.org/show_bug.cgi?id=14053
If we're in the case where we need to force a reencode and then resend of
the RPC request, due to xprt_transmit failing with a networking error, then
we _must_ retransmit the entire request.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a compatibility issue when the same buffer or string is
stored to itself. This has been seen in the field. Previously,
ACPICA would zero out the buffer/string. Now, the operation is
treated as a NOP.
http://bugzilla.acpica.org/show_bug.cgi?id=803
Reported-by: Rezwanul Kabir <Rezwanul_Kabir@Dell.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The new stack is now recommended over the old one if used for industrial
video (IIDC/DCAM) or for storage devices (SBP-2) due to better
performance, improved compatibility, added features, and security. It
should also be functionally on par with and is more secure than the old
ieee1394 stack in the use case of consumer video devices.
IP-over-1394 support for the new stack is currently emerging, and a
backend of the firedtv DVB driver to the new stack should be available
soon.
The one remaining area where the old stack is still required are audio
devices, as the new stack is not yet able to support the FFADO FireWire
audio framework.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The 32-bit parameters (len and csum) of csum_ipv6_magic() are passed in 64-bit
registers in2 and in4. The high order 32 bits of the registers were never
cleared, and garbage was sometimes calculated into the checksum.
Fix this by clearing the high order 32 bits of these registers.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because AES-NI instructions will touch XMM state, corresponding code
must be enclosed within kernel_fpu_begin/end, which used
preempt_disable/enable. So sleep should be prevented between
kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch solves the problem that the Oops(BUG_ON) occurs by rmmod.
# rmmod gianfar_driver
------------[ cut here ]------------
Kernel BUG at c01fec48 [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
MPC837x MDS
Modules linked in: gianfar_driver(-) usb_storage scsi_wait_scan
NIP: c01fec48 LR: c01febf4 CTR: c01feba8
REGS: dec5bd60 TRAP: 0700 Tainted: G W (2.6.31-rc2)
MSR: 00029032 <EE,ME,CE,IR,DR> CR: 22000424 XER: 20000000
TASK = dec4cac0[1135] 'rmmod' THREAD: dec5a000
GPR00: 00000002 dec5be10 dec4cac0 dfba1820 c035d444 c035d478 ffffffff 00000000
GPR08: 0000002b 00000001 dfba193c 00000001 22000424 10019b34 1ffcb000 00000000
GPR16: 10012008 00000000 bf82ebe0 100017ec bf82ebec bf82ebe8 bf82ebd0 00000880
GPR24: 00000000 bf82ebf0 c03532f0 c03532e4 c036b594 dfba183c dfba1800 dfba1820
NIP [c01fec48] free_netdev+0xa0/0xb8
LR [c01febf4] free_netdev+0x4c/0xb8
Call Trace:
[dec5be10] [c01febf4] free_netdev+0x4c/0xb8 (unreliable)
[dec5be30] [e105f290] gfar_remove+0x50/0x68 [gianfar_driver]
[dec5be40] [c01ec534] of_platform_device_remove+0x30/0x44
[dec5be50] [c0181760] __device_release_driver+0x68/0xc8
[dec5be60] [c0181868] driver_detach+0xa8/0xac
[dec5be80] [c0180814] bus_remove_driver+0x9c/0xd8
[dec5bea0] [c0181efc] driver_unregister+0x60/0x98
[dec5beb0] [c01ec650] of_unregister_driver+0x14/0x24
[dec5bec0] [e10631bc] gfar_exit+0x18/0x4bc [gianfar_driver]
[dec5bed0] [c0047584] sys_delete_module+0x16c/0x228
[dec5bf40] [c00116bc] ret_from_syscall+0x0/0x38
--- Exception: c01 at 0xff3669c
LR = 0x10000f34
Instruction dump:
409e0024 a07e00c0 7c63f050 4be74429 80010024 bba10014 38210020 7c0803a6
4e800020 68000003 3160ffff 7d2b0110 <0f090000> 38000004 387e01f0 901e01d4
---[ end trace 8c595bcd37230a0f ]---
localhost kernel: ------------[ cut here ]------------
Signed-off-by: Toru UCHIYAMA uchiyama.toru@jp.fujitsu.com
Signed-off-by: David S. Miller <davem@davemloft.net>
> James Bottomley (1):
> module: workaround duplicate section names
-tip testing found that this patch breaks the build on x86 if
CONFIG_KALLSYMS is disabled:
kernel/module.c: In function ‘load_module’:
kernel/module.c:2367: error: ‘struct module’ has no member named ‘sect_attrs’
distcc[8269] ERROR: compile kernel/module.c on ph/32 failed
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel] Error 2
make: *** Waiting for unfinished jobs....
Commit 1b364bf misses the fact that section attributes are only
built and dealt with if kallsyms is enabled. The patch below fixes
this.
( note, technically speaking this should depend on CONFIG_SYSFS as
well but this patch is correct too and keeps the #ifdef less
intrusive - in the KALLSYMS && !SYSFS case the code is a NOP. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Replaced patch with a slightly cleaner variation by James Bottomley ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an event has no pathname, there's no need to pad it with a null byte and
therefore generate an inotify_event sized block of zeros. This fixes a
regression introduced by commit 0db501bd0610ee0c0aca84d927f90bcccd09e2bd where
my system wouldn't finish booting because some process was being confused by
this.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (12564a): MAINTAINERS: Update gspca sn9c20x name style
V4L/DVB (12502): gspca - sn9c20x: Fix gscpa sn9c20x build errors.
V4L/DVB (12495): em28xx: Don't call em28xx_ir_init when disable_ir is true
V4L/DVB (12457): zr364: wrong indexes
V4L/DVB (12451): Update KConfig File to enable SDIO and USB interfaces
V4L/DVB (12450): Siano: Fixed SDIO compilation bugs
V4L/DVB (12449): adds webcam for Micron device MT9M111 0x143A to em28xx
V4L/DVB (12446): sms1xxx: restore GPIO functionality for all Hauppauge devices
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Reference: kernel bug#14078
http://bugzilla.kernel.org/show_bug.cgi?id=14078
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The AR req handler should not check the generation; higher level code
is the better place to handle bus generation changes. The target node
ID just needs to be checked for not being the "all nodes" address; in
this case don't handle the request and don't respond.
Use Address_Error and Type_Error rcodes as appropriate.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix a small typo in the compat ioctl handler that cause the swapext
compat handler to never be called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
arch/ia64/kernel/dma-mapping.c:14: warning: control reaches end of non-void function
arch/ia64/kernel/dma-mapping.c:14: warning: no return statement in function returning non-void
This warning was introduced by commit: 390bd132b2831a2ad0268e84bffbfc0680debfe5
Add dma_debug_init() for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.
Connect to the backend before registering our framebuffer with the kernel.
[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>