* git://git.infradead.org/mtd-2.6:
mtd: fix timeout in M25P80 driver
mtd: Bug in m25p80.c during whole-chip erase
mtd: expose subpage size via sysfs
mtd: mtd in mtd_release is unused without CONFIG_MTD_CHAR

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: MCE: make cmci_discover_lock irq-safe
x86: xen, i386: reserve Xen pagetables
x86, kexec: fix crashdump panic with CONFIG_KEXEC_JUMP
x86-64: finish cleanup_highmaps()'s job wrt. _brk_end
x86: fix boot hang in early_reserve_e820()
x86: Fix a typo in a printk message
x86, srat: do not register nodes beyond e820 map

Extend erase timeout in M25P80 SPI Flash driver.

The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.

Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (w83781d) Fix W83782D support (NULL pointer dereference)
hwmon: (asus_atk0110) Fix compiler warning

Lockdep reports the warning below when Li tries to offline one cpu:

[ 110.835487] =================================
[ 110.835616] [ INFO: inconsistent lock state ]
[ 110.835688] 2.6.30-rc4-00336-g8c9ed89 #52
[ 110.835757] ---------------------------------
[ 110.835828] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[ 110.835908] swapper/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
[ 110.835982] (cmci_discover_lock){?.+...}, at: [<ffffffff80236dc0>] cmci_clear+0x30/0x9b

cmci_clear() can be called via smp_call_function_single().

It is better to disable interrupt while holding cmci_discover_lock,
to turn it into an irq-safe lock - we can deadlock otherwise.

[ Impact: fix possible deadlock in the MCE code ]

Reported-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A03ED38.8000700@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Shaohua Li<shaohua.li@intel.com>

There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.

Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix return value for sys_ipc
microblaze: Storage class should be before const qualifier

Commit 360782dde00a2e6e7d9fd57535f90934707ab8a8 (hwmon: (w83781d) Stop
abusing struct i2c_client for ISA devices) broke W83782D support for
devices connected on the ISA bus. You will hit a NULL pointer
dereference as soon as you read any device attribute. Other devices,
and W83782D devices on the SMBus, aren't affected.

Reported-by: Michel Abraham
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Abraham

The Xen pagetables are no longer implicitly reserved as part of the other
i386_start_kernel reservations, so make sure we explicitly reserve them.
This prevents them from being released into the general kernel free page
pool and reused.

[ Impact: fix Xen guest crash ]

Also-Bisected-by: Bryan Donlan <bdonlan@gmail.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4A032EEC.30509@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

MTD has got sysfs support in 2.6.30-rc1. But subpage size is not
exposed there - do this.

UBI utilities badly need this parameter. At the moment there is
no way to get subpage size - ioctls do not return it. And we
just got sysfs support, so we can easilly extend it with this
additional parameter.

This can be merged late in the development cycle because:
1. sysfs support has been just added - there are no users for
it so far, even.
2. UBI utilities really need this parameter, and it is better
not to delay this.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fix kprobes to lock text_mutex around some arch_arm/disarm_kprobe() which
are newly added by commit de5bd88d5a5cce3cacea904d3503e5ebdb3852a2.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

atk_sensor_type is only used when DEBUG is defined.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Tim Starling reported that crashdump will panic with kernel compiled
with CONFIG_KEXEC_JUMP due to null pointer deference in
machine_kexec_32.c: machine_kexec(), when deferencing
kexec_image. Refering to:

http://bugzilla.kernel.org/show_bug.cgi?id=13265

This patch fixes the BUG via replacing global variable reference:
kexec_image in machine_kexec() with local variable reference: image,
which is more appropriate, and will not be null.

Same BUG is in machine_kexec_64.c too, so fixed too in the same way.

[ Impact: fix crash on kexec ]

Reported-by: Tim Starling <tstarling@wikimedia.org>
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1241751101.6259.85.camel@yhuang-dev.sh.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

drivers/mtd/mtdcore.c: In function 'mtd_release':
drivers/mtd/mtdcore.c:51: warning: unused variable 'mtd'

[akpm: make it actually build]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (32 commits)
[CIFS] Fix double list addition in cifs posix open code
[CIFS] Allow raw ntlmssp code to be enabled with sec=ntlmssp
[CIFS] Fix SMB uid in NTLMSSP authenticate request
[CIFS] NTLMSSP reenabled after move from connect.c to sess.c
[CIFS] Remove sparse warning
[CIFS] remove checkpatch warning
[CIFS] Fix final user of old string conversion code
[CIFS] remove cifs_strfromUCS_le
[CIFS] NTLMSSP support moving into new file, old dead code removed
[CIFS] Fix endian conversion of vcnum field
[CIFS] Remove trailing whitespace
[CIFS] Remove sparse endian warnings
[CIFS] Add remaining ntlmssp flags and standardize field names
[CIFS] Fix build warning
cifs: fix length handling in cifs_get_name_from_search_buf
[CIFS] Remove unneeded QuerySymlink call and fix mapping for unmapped status
[CIFS] rename cifs_strndup to cifs_strndup_from_ucs
Added loop check when mounting DFS tree.
Enable dfs submounts to handle remote referrals.
[CIFS] Remove older session setup implementation
...

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michal Simek <monstr@monstr.eu>

Don't check vm_region::vm_start is page aligned in add_nommu_region() because
the region may reflect some non-page-aligned mapped file, such as could be
obtained from RomFS XIP.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With the introduction of the .brk section, special care must be taken
that no unused page table entries remain if _brk_end and _end are
separated by a 2M page boundary. cleanup_highmap() runs very early and
hence cannot take care of that, hence potential entries needing to be
removed past _brk_end must be cleared once the brk allocator has done
its job.

[ Impact: avoids undesirable TLB aliases ]

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Remove adding open file entry twice to lists in the file
Do not fill file info twice in case of posix opens and creates

Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

* 'for-linus' of git://neil.brown.name/md:
md: remove rd%d links immediately after stopping an array.
md: remove ability to explicit set an inactive array to 'clean'.
md: constify VFTs
md: tidy up status_resync to handle large arrays.
md: fix some (more) errors with bitmaps on devices larger than 2TB.
md/raid10: don't clear bitmap during recovery if array will still be degraded.
md: fix loading of out-of-date bitmap.

If the first non-reserved (sub-)range doesn't fit the size requested,
an endless loop will be entered. If a range returned from
find_e820_area_size() turns out insufficient in size, the range must
be skipped before calling the function again.

[ Impact: fixes boot hang on some platforms ]

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix scheduling while holding the new active list spinlock
drm/i915: Allow tiling of objects with bit 17 swizzling by the CPU.
drm/i915: Correctly set the write flag for get_user_pages in pread.
drm/i915: Fix use of uninitialized var in 40a5f0de
drm/i915: indicate framebuffer restore key in SysRq help message
drm/i915: sync hdmi detection by hdmi identifier with 2D
drm/i915: Fix a mismerge of the IGD patch (new .find_pll hooks missed)
drm/i915: Implement batch and ring buffer dumping

On mount, "sec=ntlmssp" can now be specified to allow
"rawntlmssp" security to be enabled during
CIFS session establishment/authentication (ntlmssp used to
require specifying krb5 which was counterintuitive).

Signed-off-by: Steve French <sfrench@us.ibm.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Fix min function comparison warning
ecryptfs: fix printk format warning

It's a really simple patch that basically just open-codes the current
"secure_ip_id()" call, but when open-coding it we now use a _static_
hashing area, so that it gets updated every time.

And to make sure somebody can't just start from the same original seed of
all-zeroes, and then do the "half_md4_transform()" over and over until
they get the same sequence as the kernel has, each iteration also mixes in
the same old "current->pid + jiffies" we used - so we should now have a
regular strong pseudo-number generator, but we also have one that doesn't
have a single seed.

Note: the "pid + jiffies" is just meant to be a tiny tiny bit of noise. It
has no real meaning. It could be anything. I just picked the previous
seed, it's just that now we keep the state in between calls and that will
feed into the next result, and that should make all the difference.

I made that hash be a per-cpu data just to avoid cache-line ping-pong:
having multiple CPU's write to the same data would be fine for randomness,
and add yet another layer of chaos to it, but since get_random_int() is
supposed to be a fast interface I did it that way instead. I considered
using "__raw_get_cpu_var()" to avoid any preemption overhead while still
getting the hash be _mostly_ ping-pong free, but in the end good taste won
out.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

md maintains link in sys/mdXX/md/ to identify which device has
which role in the array. e.g.
rd2 -> dev-sda

indicates that the device with role '2' in the array is sda.

These links are only present when the array is active. They are
created immediately after ->run is called, and so should be removed
immediately after ->stop is called.
However they are currently removed a little bit later, and it is
possible for ->run to be called again, thus adding these links, before
they are removed.

So move the removal earlier so they are consistently only present when
the array is active.

Signed-off-by: NeilBrown <neilb@suse.de>

[ Impact: printk message cleanup ]

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
LKML-Reference: <200905040908.27299.knikanth@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Revert part of af5c820a3169e81af869c113e18ec7588836cd50 ("x86: cpumask:
use work_on_cpu in arch/x86/kernel/microcode_core.c")

That change is causing only one Intel CPU's microcode to be updated e.g.
microcode: CPU3 updated from revision 0x9 to 0x17, date = 2005-04-22
where before it announced that also for CPU0 and CPU1 and CPU2.

We cannot use work_on_cpu() in the CONFIG_MICROCODE_OLD_INTERFACE code,
because Intel's request_microcode_user() involves a copy_from_user() from
/sbin/microcode_ctl, which therefore needs to be on that CPU at the time.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

regression caused by commit 5e118f4139feafe97e913df67b1f7c1e5083e535:
i915_gem_object_move_to_inactive() should be called in task context,
as it calls fput();

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
[anholt: Add more detail to the comment about the lock break that's added]
Signed-off-by: Eric Anholt <eric@anholt.net>

We were not setting the SMB uid in NTLMSSP authenticate
request which could lead to INVALID_PARAMETER error
on 2nd session setup.

Signed-off-by: Steve French <sfrench@us.ibm.com>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (11652): au0828: fix kernel oops regression on USB disconnect.
V4L/DVB (11626): cx23885: Two fixes for DViCO FusionHDTV DVB-T Dual Express
V4L/DVB (11612): mx3_camera: Fix compilation with CONFIG_PM
V4L/DVB (11570): patch: s2255drv: fix race condition on set mode
V4L/DVB (11568): cx18: Fix the handling of i2c bus registration error
V4L/DVB (11561a): move media after i2c
V4L/DVB (11516): drivers/media/video/saa5246a.c: fix use-after-free
V4L/DVB (11515): drivers/media/video/saa5249.c: fix use-after-free and leak
V4L/DVB (11494a): cx231xx Kconfig fixes
V4L/DVB (11494): cx18: Send correct input routing value to external audio multiplexers

This warning shows up on 64 bit builds:

fs/ecryptfs/inode.c:693: warning: comparison of distinct pointer types
lacks a cast

Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>

* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5507/1: support R_ARM_MOVW_ABS_NC and MOVT_ABS relocation types
[ARM] 5506/1: davinci: DMA_32BIT_MASK --> DMA_BIT_MASK(32)
i.MX31: Disable CPU_32v6K in mx3_defconfig.
mx3fb: Fix compilation with CONFIG_PM
mx27ads: move PBC mapping out of vmalloc space
MXC: remove BUG_ON in interrupt handler
mx31: remove mx31moboard_defconfig
ARM: ARCH_MXC should select HAVE_CLK
mxc : BUG in imx_dma_request
mxc : Clean up properly when imx_dma_free() used without imx_dma_disable()
[ARM] mv78xx0: update defconfig
[ARM] orion5x: update defconfig
[ARM] Kirkwood: update defconfig
[ARM] Kconfig typo fix: "PXA930" -> "CPU_PXA930".
[ARM] S3C2412: Add missing cache flush in suspend code
[ARM] S3C: Add UDIVSLOT support for newer UARTS
[ARM] S3C64XX: Add S3C64XX_PA_IIS{0,1} to <mach/map.h>

Being able to write 'clean' to an 'array_state' of an inactive array
to activate it in 'clean' mode is both unnecessary and inconvenient.

It is unnecessary because the same can be achieved by writing
'active'. This activates and array, but it still remains 'clean'
until the first write.

It is inconvenient because writing 'clean' is more often used to
cause an 'active' array to revert to 'clean' mode (thus blocking
any writes until a 'write-pending' is promoted to 'active').

Allowing 'clean' to both activate an array and mark an active array as
clean can lead to races: One program writes 'clean' to mark the
active array as clean at the same time as another program writes
'inactive' to deactivate (stop) and active array. Depending on which
writes first, the array could be deactivated and immediately
reactivated which isn't what was desired.

So just disable the use of 'clean' to activate an array.

This avoids a race that can be triggered with mdadm-3.0 and external
metadata, so it suitable for -stable.

Reported-by: Rafal Marszewski <rafal.marszewski@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>

The mem= option will truncate the memory map at a specified address so
it's not possible to register nodes with memory beyond the e820 upper
bound.

unparse_node() is only called when then node had memory associated with
it, although with the mem= option it is no longer addressable.

[ Impact: fix boot hang on certain (large) systems ]

Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <alpine.DEB.2.00.0905051248150.20021@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: warn about lockdep disabling after kernel taint, fix

Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.

Signed-off-by: Eric Anholt <eric@anholt.net>

The NTLMSSP code was removed from fs/cifs/connect.c and merged
(75% smaller, cleaner) into fs/cifs/sess.c

As with the old code it requires that cifs be built with
CONFIG_CIFS_EXPERIMENTAL, the /proc/fs/cifs/Experimental flag
must be set to 2, and mount must turn on extended security
(e.g. with sec=krb5).

Although NTLMSSP encapsulated in SPNEGO is not enabled yet,
"raw" ntlmssp is common and useful in some cases since it
offers more complete security negotiation, and is the
default way of negotiating security for many Windows systems.
SPNEGO encapsulated NTLMSSP will be able to reuse the same
code.

Signed-off-by: Steve French <sfrench@us.ibm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
e100: do not go D3 in shutdown unless system is powering off
netfilter: revised locking for x_tables
Bluetooth: Fix connection establishment with low security requirement
Bluetooth: Add different pairing timeout for Legacy Pairing
Bluetooth: Ensure that HCI sysfs add/del is preempt safe
net: Avoid extra wakeups of threads blocked in wait_for_packet()
net: Fix typo in net_device_ops description.
ipv4: Limit size of route cache hash table
Add reference to CAPI 2.0 standard
Documentation/isdn/INTERFACE.CAPI
update Documentation/isdn/00-INDEX
ixgbe: Fix WoL functionality for 82599 KX4 devices
veth: prevent oops caused by netdev destructor
xfrm: wrong hash value for temporary SA
forcedeth: tx timeout fix
net: Fix LL_MAX_HEADER for CONFIG_TR_MODULE
mlx4_en: Handle page allocation failure during receive
mlx4_en: Fix cleanup flow on cq activation
vlan: update vlan carrier state for admin up/down
netfilter: xt_recent: fix stack overread in compat code
...

A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

fs/ecryptfs/inode.c:670: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Fix zillions of -mm x86_64 allmodconfig build errors - the file uses
EXPORT_SYMBOL() and kmalloc but misses the needed includes.

Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From: Bruce Ashfield <bruce.ashfield@windriver.com>

To fully support the armv7-a instruction set/optimizations, support
for the R_ARM_MOVW_ABS_NC and R_ARM_MOVT_ABS relocation types is
required.

The MOVW and MOVT are both load-immediate instructions, MOVW loads 16
bits into the bottom half of a register, and MOVT loads 16 bits into the
top half of a register.

The relocation information for these instructions has a full 32 bit
value, plus an addend which is stored in the 16 immediate bits in the
instruction itself. The immediate bits in the instruction are not
contiguous (the register # splits it into a 4 bit and 12 bit value),
so the addend has to be extracted accordingly and added to the value.
The value is then split and put into the instruction; a MOVW uses the
bottom 16 bits of the value, and a MOVT uses the top 16 bits.

Signed-off-by: David Borman <david.borman@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: NeilBrown <neilb@suse.de>

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r128: fix r128 ioremaps to use ioremap_wc.
drm: cleanup properly in drm_get_dev() failure paths
drm: clean the map list before destroying the hash table
drm: remove unreachable code in drm_sysfs.c
drm: add control node checks missing from kms merge
drm/kms: don't try to shortcut drm mode set function
drm/radeon: bump minor version for occlusion queries support

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix "direct_io" private mmap
fuse: fix argument type in fuse_get_user_pages()

Impact: build fix for Sparc and s390

Stephen Rothwell reported that the Sparc build broke:

In file included from kernel/panic.c:12:
include/linux/debug_locks.h: In function '__debug_locks_off':
include/linux/debug_locks.h:15: error: implicit declaration of function 'xchg'

due to:

9eeba61: lockdep: warn about lockdep disabling after kernel taint

There is some inconsistency between architectures about where exactly
xchg() is defined.

The traditional place is in system.h but the more logical point for it
is in atomic.h - where most architectures (especially new ones) have
it defined. These architecture also still offer it via system.h.

Some, such as Sparc or s390 only have it in asm/system.h and not available
via asm/atomic.h at all.

Use the widest set of headers in debug_locks.h and also include asm/system.h.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20090414144317.026498df.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Otherwise, the results of our read didn't show up when we were faulting in
the page being read into (as happened with a testcase reading into a big
stack area). Likely accounts for some conformance test failures.

Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Steve French <sfrench@us.ibm.com>

* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix up error path leak in i915_cmdbuffer
drm/i915: fix unpaired i915 device mutex on entervt failure.
drm/i915: add support for G41 chipset
drm/i915: Enable ASLE if present
drm/i915: Unregister ACPI video driver when exiting
drm/i915: Register ACPI video even when not modesetting
drm/i915: fix transition to I915_TILING_NONE
drm/i915: Don't let an oops get triggered from irq_emit without dma init.
drm/i915: allow tiled front buffers on 965+

After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two fixes for DViCO FusionHDTV DVB-T Dual Express:

* Reset correct tuner when reinitializing xc3028.
* Disable the I2C gate control to avoid locking up the I2C bus.

Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

With the removal of duplicate unpack_to_rootfs() (commit
df52092f3c97788592ef72501a43fb7ac6a3cfe0) the messages displayed do not
actually correspond to what the kernel is doing. In addition, depending
if ramdisks are supported or not, the messages are not at all the same.

So keep the messages more in sync with what is really doing the kernel,
and only display a second message in case of failure. This also ensure
that the printk message cannot be split by other printk's.

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As per commit 284901a90a9e0b812ca3f5f852cbbfb60d10249d, use
DMA_BIT_MASK(n)

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Two problems in status_resync.
1/ It still used Kilobytes as the basic block unit, while most code
now uses sectors uniformly.
2/ It doesn't allow for the possibility that max_sectors exceeds
the range of "unsigned long".

So
- change "max_blocks" to "max_sectors", and store sector numbers
in there and in 'resync'
- Make 'rt' a 'sector_t' so it can temporarily hold the number of
remaining sectors.
- use sector_div rather than normal division.
- change the magic '100' used to preserve precision to '32'.
+ making it a power of 2 makes division easier
+ it doesn't need to be as large as it was chosen when we averaged
speed over the entire run. Now we average speed over the last 30
seconds or so.

Reported-by: "Mario 'BitKoenig' Holbe" <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: NeilBrown <neilb@suse.de>