tjh.dev
commits
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: Support PCI IO access of SH7780 base boards.
sh: Fix PCI IO space base address of SH7780.
The old code did did only work as long as CFE and the kernel were using
the same interrupt numbering ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IO access of PCI is not supported in R7780RP and the MS7780SE
board now. The support of the IO access mode of e100 and a lot of IDE
chips becomes possible by fixing the code.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix x86-32 early fixmap initialization.
x86: disable hpet legacy replacement for kdump
x86: disable hpet on shutdown
PCI IO space base address of SH7780 was wrong.
Change from 0xFE400000 to 0xFE200000.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc
Revert "[POWERPC] Fix RTAS os-term usage on kernel panic"
pageexec@freemail.hu writes:
> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)
Thanks for the reminder I thought we had fixed this problem a while ago.
Needed to get fixed virtual address for USB debug and earlycon with mmio.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
x86 setup: don't recalculate ss:esp unless really necessary
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
ACPI: Delete the IRQ operation in throttling controll via PTC
xmon is broken under arch/ppc so remove it from the defconfig.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
we should also add hpet_disable() for kdump.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdio_uart: fix sign of paramter status in sdio_uart_receive_chars()
In order to work around old LILO versions providing an invalid ss
register, the current setup code always sets up a new stack,
immediately following .bss and the heap. But this breaks LOADLIN.
This rewrite of the workaround checks for an invalid stack (ss!=ds)
first, and leaves ss:sp alone otherwise (apart from aligning esp).
[hpa note: LOADLIN has a number of arbitrary hard-coded limits that
are being pushed up against. Without some major revision of LOADLIN
itself it will not be sustainable keeping it alive. This gives it
another brief lease on life, however. This patch also helps the
cmdline truncation problem with old versions of SYSLINUX.]
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: cpu accounting controller (V2)
This reverts commit a2b51812a4dc5db09ab4d4638d4d8ed456e2457e.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2.6.11 gave __GFP_ZERO's prep_zero_page a bogus "highmem may have to wait"
assertion. Presumably added under the misconception that clear_highpage
uses nonatomic kmap; but then and now it uses kmap_atomic, so no problem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] NCR5380: Fix bugs and canonicalize irq handler usage
[SCSI] zfcp: fix cleanup of dismissed error recovery actions
[SCSI] zfcp: fix dismissal of error recovery actions
[SCSI] qla1280: convert to use the data buffer accessors
[SCSI] iscsi: return data transfer residual for data-out commands
[SCSI] iscsi_tcp: fix potential lockup with write commands
[SCSI] aacraid: fix security weakness
[SCSI] aacraid: fix up le32 issues in BlinkLED
[SCSI] aacraid: fix potential panic in thread stop
[SCSI] aacraid: don't assign cpu_to_le32(constant) to u8
Commit cfb5285660aad4931b2ebbfa902ea48a37dfffa1 removed a useful feature for
us, which provided a cpu accounting resource controller. This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.
The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df64065e7c135d0002f069444fbdfc64768f), with
these differences:
- Removed load average information. I felt it needs more thought (esp
to deal with SMP and virtualized platforms) and can be added for
2.6.25 after more discussions.
- Convert group cpu usage to be nanosecond accurate (as rest of the cfs
stats are) and invoke cpuacct_charge() from the respective scheduler
classes
- Make accounting scalable on SMP systems by splitting the usage
counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
code is not big enough to warrant a new file and also this rightly
needs to live inside the scheduler. Also things like accessing
rq->lock while reading cpu usage becomes easier if the code lived in
kernel/sched.c)
The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
some simple tests like cpuspin (spin on the cpu), ran several tasks in
the same group and timed them. Compared their time stamps with
cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changed resolution of named references in packages
Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.
http://bugzilla.kernel.org/show_bug.cgi?id=5328
http://bugzilla.kernel.org/show_bug.cgi?id=9429
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix static rate if path faster than link
IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tmpfs was misconverted to __GFP_ZERO in 2.6.11. There's an unusual case in
which shmem_getpage receives the page from its caller instead of allocating.
We must cover this case by clear_highpage before SetPageUptodate, as before.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
* Always pass the same value to free_irq() that we pass to
request_irq(). This fixes several bugs.
* Always call NCR5380_intr() with 'irq' and 'dev_id' arguments.
Note, scsi_falcon_intr() is the only case now where dev_id is not the
scsi_host.
* Always pass Scsi_Host to request_irq(). For most cases, the drivers
already did so, and I merely neated the source code line. In other
cases, either NULL or a non-sensical value was passed, verified to be
unused, then changed to be Scsi_Host in anticipation of the future.
In addition to the bugs fixes, this change makes the interface usage
consistent, which in turn enables the possibility of directly
referencing Scsi_Host from all NCR5380_intr() invocations.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.
This fixes an oops on T61 -- a regression due to
f79f06ab9f86 b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix build.
[MIPS] Fix use of smp_processor_id() in preemptible code.
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: clean up kernel/sched_stat.h
sched: clean up overlong line in kernel/sched_debug.c
sched: clean up, move __sched_text_start/end to sched.h
sched: clean up sd_alloc_ctl_cpu_table() definition
softlockup: fix false positives on CONFIG_NOHZ
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
LIB82596: correct data types for hardware addresses
via-velocity: don't oops on MTU change (resend)
Stop phy code from returning success to unknown ioctls.
SET_NETDEV_DEV() in fec_mpc52xx.c
net: smc911x: only enable for mpr2 on sh.
e1000: Fix NAPI state bug when Rx complete
sky2: turn of dynamic Tx watermark workaround (FE+ only)
sky2: don't use AER routines
sky2: revert to access PCI config via device space
cxgb - fix stats
cxgb - fix NAPI
cxgb - fix T2 GSO
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
phylib: marvell: add support for TX-only and RX-only Internal Delay
phylib: add PHY interface modes for internal delay for tx and rx only
skge: MTU changing fix
skge: serial mode register values
skge version 1.13
skge: increase TX threshold for Jumbo
skge: fiber link up/down fix
...
The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.
This patch fixes it by introducing a separate mutex to protect the
handling of handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Calling zfcp_erp_strategy_check_action() after zfcp_erp_action_to_running()
in zfcp_erp_strategy() might cause an unbalanced up() for erp_ready_sem,
which makes the zfcp recovery fail somewhere along the way:
erp thread processing erp_action:
|
| someone waking up erp thread for erp_action
| |
| | someone else dismissing erp_action:
| | |
V V V
write_lock_irqsave(&adapter->erp_lock, flags);
...
if (zfcp_erp_action_exists(erp_action) == ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem); /* first up() for erp_action */
}
write_unlock_irqrestore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
...
zfcp_erp_action_to_running(erp_action);
write_unlock_restore(&adapter->erp_lock, flags);
/* processing erp_action */
write_lock_irqsave(&adapter->erp_lock, flags);
...
erp_action->status |= ZFCP_STATUS_ERP_DISMISSED;
if (zfcp_erp_action_exists(erp_action) ==
ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem);
/* second, unbalanced up() for erp_action */
}
...
write_unlock_restore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
if (erp_action->status & ZFCP_STATUS_ERP_DISMISSED) {
zfcp_erp_action_dequeue(erp_action);
retval = ZFCP_ERP_DISMISSED;
}
...
write_unlock_restore(&adapter->erp_lock, flags);
down(&adapter->erp_ready_sem);
/* this down() is meant to balance the first up() */
The erp thread must not dismiss an erp_action after moving that action to
erp_running_head. Instead it should just go through the down() operation,
which balances the first up(), and run through zfcp_erp_strategy one more
time for the second up(), which eventually cleans up erp_action. Which
is similar to the normal processing of an event for erp_action doing
something asynchronously (e.g. waiting for the completion of an fsf_req).
This only works if we make sure that a dismissed erp_action is passed to
zfcp_erp_strategy() prior to the other action, which caused actions to be
dismissed. Therefore the patch implements this rule: running actions go to
the head of the ready list; new actions go to the tail of the ready list;
the erp thread picks actions to be processed from the ready list's head.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
If a port goes down, ipoib_ib_dev_down() is invoked -- which flushes
the mcasts (clearing priv->broadcast) and clearing the path record
cache. If ipoib_start_xmit() is then invoked (before the broadcast
group is rejoined), a kernel oops results from attempting to access
priv->broadcast, which is still unset.
Returning NULL from path_rec_create() if priv->broadcast is NULL is a
harmless way of bypassing the problem -- the offending packet is
simply discarded "without prejudice."
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make them depend on TCGETS2. If that one is implemented the rest should be
there as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix: http://bugzilla.kernel.org/show_bug.cgi?id=3043
only allow coredumping to the same uid that the coredumping
task runs under.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clean up kernel/sched_stat.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix broken Marvell 7042 support.
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
ata_piix: add more toshiba laptops to broken suspend list
libata: More IVB horkage from TSST
libata: report protocol and full CDB on error
Several fixes for the AVR32 PATA driver
sata_mv: fix compilation error when enabling DEBUG
Set proper ATA UDMA mode for bf548 according to system clock.
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Well I clearly goofed when I added the initial network namespace support
for /proc/net. Currently things work but there are odd details visible to
user space, even when we have a single network namespace.
Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.
To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.
As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
zfcp_erp_action_dismiss() used to ignore any actions in the ready list. This
is a bug. Any action superseded by a stronger action needs to be dismissed.
This patch changes zfcp_erp_action_dismiss() so that it dismisses actions
regardless of their list affiliation. The ERP thread is able to handle this.
It is important to kick the erp thread only for actions in the running list,
though, as an imbalance of wakeup signals would confuse the erp thread
otherwise.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON. Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.
The call was added as part of commit ddc2e812d592457747c4367fb73edcaa8e1e49ff
with the comment that "overhead should be minimal". It may have been
minimal at the time, but it isn't now.
[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
performance regression but rather the virt_to_head_page() changes to
virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
[<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
[<802e4b84>] debug_smp_processor_id+0xd4/0xf0
[<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.
Cpu options of cpu0 are assumed to be the superset of all processors.
Can I make the same assumptions for cache line size and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-scsi: use print_hex_dump from <linux/kernel.h>
ide: More TSST drives with broken cable detection
ali14xx: constify __initdata
ide: remove bogus ide_fix_driveid() comment
trm290: remove bogus init_hwif_trm290() comment
piix: add HP compaq laptop to short cable list
alim15x3: add Mitac 8317 and derivatives to ali_cable_override()
ide: add TORiSAN model: CD-ROM CDR_U200 fw: 1.09 to DMA blacklist
amd74xx: arm hack
drivers/ide: Add missing "space"
ide-cris: don't override ide_register_hw() result
ide: move CONFIG_IDE_ETRAX to drivers/ide/Kconfig
ide: add CONFIG_IDE_H8300 config option
ide/Kconfig: fix mpc8xx host driver dependencies
macide/q40ide: add missing __init tag to {macide,q40ide}_init()
aec62xx: Fix kernel oops in driver's probe function
ide: skip ide_wait_not_busy() on noprobe-disks
siimage: remove resetproc() method
ide: don't set PIO mode on pre-EIDE drives
sis5513.c: Add Packard Bell EasyNote K5305 to laptops
In wait_task_stopped() exit_code already contains the right value for the
si_status member of siginfo, and this is simply set in the non WNOWAIT
case.
If you call waitid() with a stopped or traced process, you'll get the signal
in siginfo.si_status as expected -- however if you call waitid(WNOWAIT) at the
same time, you'll get the signal << 8 | 0x7f
Pass it unchanged to wait_noreap_copyout(); we would only need to shift it
and add 0x7f if we were returning it in the user status field and that
isn't used for any function that permits WNOWAIT.
Signed-off-by: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: reverse inline-data truncate args
ocfs2: Fix comparison in ocfs2_size_fits_inline_data()
ocfs2: Remove bug statement in ocfs2_dentry_iput()
[PATCH] ocfs2: Remove expensive bitmap scanning
ocfs2: log valid inode # on bad inode
ocfs2: Filter -ENOSPC in mlog_errno()
[PATCH] fs/ocfs2: Add missing "space"
ocfs2: Reset journal parameters after s_mount_opt update
clean up overlong line in kernel/sched_debug.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pageexec@freemail.hu writes:
> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)
Thanks for the reminder I thought we had fixed this problem a while ago.
Needed to get fixed virtual address for USB debug and earlycon with mmio.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to work around old LILO versions providing an invalid ss
register, the current setup code always sets up a new stack,
immediately following .bss and the heap. But this breaks LOADLIN.
This rewrite of the workaround checks for an invalid stack (ss!=ds)
first, and leaves ss:sp alone otherwise (apart from aligning esp).
[hpa note: LOADLIN has a number of arbitrary hard-coded limits that
are being pushed up against. Without some major revision of LOADLIN
itself it will not be sustainable keeping it alive. This gives it
another brief lease on life, however. This patch also helps the
cmdline truncation problem with old versions of SYSLINUX.]
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit a2b51812a4dc5db09ab4d4638d4d8ed456e2457e.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2.6.11 gave __GFP_ZERO's prep_zero_page a bogus "highmem may have to wait"
assertion. Presumably added under the misconception that clear_highpage
uses nonatomic kmap; but then and now it uses kmap_atomic, so no problem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] NCR5380: Fix bugs and canonicalize irq handler usage
[SCSI] zfcp: fix cleanup of dismissed error recovery actions
[SCSI] zfcp: fix dismissal of error recovery actions
[SCSI] qla1280: convert to use the data buffer accessors
[SCSI] iscsi: return data transfer residual for data-out commands
[SCSI] iscsi_tcp: fix potential lockup with write commands
[SCSI] aacraid: fix security weakness
[SCSI] aacraid: fix up le32 issues in BlinkLED
[SCSI] aacraid: fix potential panic in thread stop
[SCSI] aacraid: don't assign cpu_to_le32(constant) to u8
Commit cfb5285660aad4931b2ebbfa902ea48a37dfffa1 removed a useful feature for
us, which provided a cpu accounting resource controller. This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.
The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df64065e7c135d0002f069444fbdfc64768f), with
these differences:
- Removed load average information. I felt it needs more thought (esp
to deal with SMP and virtualized platforms) and can be added for
2.6.25 after more discussions.
- Convert group cpu usage to be nanosecond accurate (as rest of the cfs
stats are) and invoke cpuacct_charge() from the respective scheduler
classes
- Make accounting scalable on SMP systems by splitting the usage
counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
code is not big enough to warrant a new file and also this rightly
needs to live inside the scheduler. Also things like accessing
rq->lock while reading cpu usage becomes easier if the code lived in
kernel/sched.c)
The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
some simple tests like cpuspin (spin on the cpu), ran several tasks in
the same group and timed them. Compared their time stamps with
cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changed resolution of named references in packages
Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.
http://bugzilla.kernel.org/show_bug.cgi?id=5328
http://bugzilla.kernel.org/show_bug.cgi?id=9429
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tmpfs was misconverted to __GFP_ZERO in 2.6.11. There's an unusual case in
which shmem_getpage receives the page from its caller instead of allocating.
We must cover this case by clear_highpage before SetPageUptodate, as before.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
* Always pass the same value to free_irq() that we pass to
request_irq(). This fixes several bugs.
* Always call NCR5380_intr() with 'irq' and 'dev_id' arguments.
Note, scsi_falcon_intr() is the only case now where dev_id is not the
scsi_host.
* Always pass Scsi_Host to request_irq(). For most cases, the drivers
already did so, and I merely neated the source code line. In other
cases, either NULL or a non-sensical value was passed, verified to be
unused, then changed to be Scsi_Host in anticipation of the future.
In addition to the bugs fixes, this change makes the interface usage
consistent, which in turn enables the possibility of directly
referencing Scsi_Host from all NCR5380_intr() invocations.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.
This fixes an oops on T61 -- a regression due to
f79f06ab9f86 b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: clean up kernel/sched_stat.h
sched: clean up overlong line in kernel/sched_debug.c
sched: clean up, move __sched_text_start/end to sched.h
sched: clean up sd_alloc_ctl_cpu_table() definition
softlockup: fix false positives on CONFIG_NOHZ
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
LIB82596: correct data types for hardware addresses
via-velocity: don't oops on MTU change (resend)
Stop phy code from returning success to unknown ioctls.
SET_NETDEV_DEV() in fec_mpc52xx.c
net: smc911x: only enable for mpr2 on sh.
e1000: Fix NAPI state bug when Rx complete
sky2: turn of dynamic Tx watermark workaround (FE+ only)
sky2: don't use AER routines
sky2: revert to access PCI config via device space
cxgb - fix stats
cxgb - fix NAPI
cxgb - fix T2 GSO
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
phylib: marvell: add support for TX-only and RX-only Internal Delay
phylib: add PHY interface modes for internal delay for tx and rx only
skge: MTU changing fix
skge: serial mode register values
skge version 1.13
skge: increase TX threshold for Jumbo
skge: fiber link up/down fix
...
The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.
This patch fixes it by introducing a separate mutex to protect the
handling of handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Calling zfcp_erp_strategy_check_action() after zfcp_erp_action_to_running()
in zfcp_erp_strategy() might cause an unbalanced up() for erp_ready_sem,
which makes the zfcp recovery fail somewhere along the way:
erp thread processing erp_action:
|
| someone waking up erp thread for erp_action
| |
| | someone else dismissing erp_action:
| | |
V V V
write_lock_irqsave(&adapter->erp_lock, flags);
...
if (zfcp_erp_action_exists(erp_action) == ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem); /* first up() for erp_action */
}
write_unlock_irqrestore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
...
zfcp_erp_action_to_running(erp_action);
write_unlock_restore(&adapter->erp_lock, flags);
/* processing erp_action */
write_lock_irqsave(&adapter->erp_lock, flags);
...
erp_action->status |= ZFCP_STATUS_ERP_DISMISSED;
if (zfcp_erp_action_exists(erp_action) ==
ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem);
/* second, unbalanced up() for erp_action */
}
...
write_unlock_restore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
if (erp_action->status & ZFCP_STATUS_ERP_DISMISSED) {
zfcp_erp_action_dequeue(erp_action);
retval = ZFCP_ERP_DISMISSED;
}
...
write_unlock_restore(&adapter->erp_lock, flags);
down(&adapter->erp_ready_sem);
/* this down() is meant to balance the first up() */
The erp thread must not dismiss an erp_action after moving that action to
erp_running_head. Instead it should just go through the down() operation,
which balances the first up(), and run through zfcp_erp_strategy one more
time for the second up(), which eventually cleans up erp_action. Which
is similar to the normal processing of an event for erp_action doing
something asynchronously (e.g. waiting for the completion of an fsf_req).
This only works if we make sure that a dismissed erp_action is passed to
zfcp_erp_strategy() prior to the other action, which caused actions to be
dismissed. Therefore the patch implements this rule: running actions go to
the head of the ready list; new actions go to the tail of the ready list;
the erp thread picks actions to be processed from the ready list's head.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
If a port goes down, ipoib_ib_dev_down() is invoked -- which flushes
the mcasts (clearing priv->broadcast) and clearing the path record
cache. If ipoib_start_xmit() is then invoked (before the broadcast
group is rejoined), a kernel oops results from attempting to access
priv->broadcast, which is still unset.
Returning NULL from path_rec_create() if priv->broadcast is NULL is a
harmless way of bypassing the problem -- the offending packet is
simply discarded "without prejudice."
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make them depend on TCGETS2. If that one is implemented the rest should be
there as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix: http://bugzilla.kernel.org/show_bug.cgi?id=3043
only allow coredumping to the same uid that the coredumping
task runs under.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix broken Marvell 7042 support.
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
ata_piix: add more toshiba laptops to broken suspend list
libata: More IVB horkage from TSST
libata: report protocol and full CDB on error
Several fixes for the AVR32 PATA driver
sata_mv: fix compilation error when enabling DEBUG
Set proper ATA UDMA mode for bf548 according to system clock.
Well I clearly goofed when I added the initial network namespace support
for /proc/net. Currently things work but there are odd details visible to
user space, even when we have a single network namespace.
Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.
To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.
As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
zfcp_erp_action_dismiss() used to ignore any actions in the ready list. This
is a bug. Any action superseded by a stronger action needs to be dismissed.
This patch changes zfcp_erp_action_dismiss() so that it dismisses actions
regardless of their list affiliation. The ERP thread is able to handle this.
It is important to kick the erp thread only for actions in the running list,
though, as an imbalance of wakeup signals would confuse the erp thread
otherwise.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON. Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.
The call was added as part of commit ddc2e812d592457747c4367fb73edcaa8e1e49ff
with the comment that "overhead should be minimal". It may have been
minimal at the time, but it isn't now.
[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
performance regression but rather the virt_to_head_page() changes to
virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
[<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
[<802e4b84>] debug_smp_processor_id+0xd4/0xf0
[<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.
Cpu options of cpu0 are assumed to be the superset of all processors.
Can I make the same assumptions for cache line size and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-scsi: use print_hex_dump from <linux/kernel.h>
ide: More TSST drives with broken cable detection
ali14xx: constify __initdata
ide: remove bogus ide_fix_driveid() comment
trm290: remove bogus init_hwif_trm290() comment
piix: add HP compaq laptop to short cable list
alim15x3: add Mitac 8317 and derivatives to ali_cable_override()
ide: add TORiSAN model: CD-ROM CDR_U200 fw: 1.09 to DMA blacklist
amd74xx: arm hack
drivers/ide: Add missing "space"
ide-cris: don't override ide_register_hw() result
ide: move CONFIG_IDE_ETRAX to drivers/ide/Kconfig
ide: add CONFIG_IDE_H8300 config option
ide/Kconfig: fix mpc8xx host driver dependencies
macide/q40ide: add missing __init tag to {macide,q40ide}_init()
aec62xx: Fix kernel oops in driver's probe function
ide: skip ide_wait_not_busy() on noprobe-disks
siimage: remove resetproc() method
ide: don't set PIO mode on pre-EIDE drives
sis5513.c: Add Packard Bell EasyNote K5305 to laptops
In wait_task_stopped() exit_code already contains the right value for the
si_status member of siginfo, and this is simply set in the non WNOWAIT
case.
If you call waitid() with a stopped or traced process, you'll get the signal
in siginfo.si_status as expected -- however if you call waitid(WNOWAIT) at the
same time, you'll get the signal << 8 | 0x7f
Pass it unchanged to wait_noreap_copyout(); we would only need to shift it
and add 0x7f if we were returning it in the user status field and that
isn't used for any function that permits WNOWAIT.
Signed-off-by: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: reverse inline-data truncate args
ocfs2: Fix comparison in ocfs2_size_fits_inline_data()
ocfs2: Remove bug statement in ocfs2_dentry_iput()
[PATCH] ocfs2: Remove expensive bitmap scanning
ocfs2: log valid inode # on bad inode
ocfs2: Filter -ENOSPC in mlog_errno()
[PATCH] fs/ocfs2: Add missing "space"
ocfs2: Reset journal parameters after s_mount_opt update
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>