tjh.dev
commits
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] make pfm_get_task work with virtual pids
[IA64] honor notify_die() returning NOTIFY_STOP
[IA64] remove dead code: __cpu_{down,die} from !HOTPLUG_CPU
[IA64] Appoint kvm/ia64 Maintainers
[IA64] ia64_set_psr should use srlz.i
[IA64] Export three symbols for module use
[IA64] mca style cleanup
[IA64] sn_hwperf semaphore to mutex
[IA64] generalize attribute of fsyscall_gtod_data
[IA64] efi.c Add /* never reached */ annotation
[IA64] efi.c Spelling/punctuation fixes
[IA64] Make efi.c mostly fit in 80 columns
[IA64] aliasing-test: fix gcc warnings on non-ia64
[IA64] Slim-down __clear_bit_unlock
[IA64] Fix the order of atomic operations in restore_previous_kprobes on ia64
[IA64] constify function pointer tables
[IA64] fix userspace compile error in gcc_intrin.h
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] dcss: Initialize workqueue before using it.
[S390] Remove BUILD_BUG_ON() in vmem code.
[S390] sclp_tty/sclp_vt220: Fix scheduling while atomic
[S390] dasd: fix panic caused by alias device offline
[S390] dasd: add ifcc handling
[S390] latencytop s390 support.
[S390] Implement ext2_find_next_bit.
[S390] Cleanup & optimize bitops.
[S390] Define GENERIC_LOCKBREAK.
[S390] console: allow vt220 console to be the only console
[S390] Fix couple of section mismatches.
[S390] Fix smp_call_function_mask semantics.
[S390] Fix linker script.
[S390] DEBUG_PAGEALLOC support for s390.
[S390] cio: Add shutdown callback for ccwgroup.
[S390] cio: Update documentation.
[S390] cio: Clean up chsc response code handling.
[S390] cio: make sense id procedure work with partial hardware response
This pid comes from user space, so treat it accordingly.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[PKT_SCHED]: vlan tag match
[NET]: Add if_addrlabel.h to sanitized headers.
[NET] rtnetlink.c: remove no longer used functions
[ICMP]: Restore pskb_pull calls in receive function
[INET]: Fix accidentally broken inet(6)_hash_connect's port offset calculations.
[NET]: Remove further references to net-modules.txt
bluetooth rfcomm tty: destroy before tty_close()
bluetooth: blacklist another Broadcom BCM2035 device
drivers/bluetooth/btsdio.c: fix double-free
drivers/bluetooth/bpa10x.c: fix memleak
bluetooth: uninlining
bluetooth: hidp_process_hid_control remove unnecessary parameter dealing
tun: impossible to deassert IFF_ONE_QUEUE or IFF_NO_PI
hamradio: fix dmascc section mismatch
[SCTP]: Fix kernel panic while received AUTH chunk with BAD shared key identifier
[SCTP]: Fix kernel panic while received AUTH chunk while enabled auth
[IPV4]: Formatting fix for /proc/net/fib_trie.
[IPV6]: Fix sysctl compilation error.
[NET_SCHED]: Add #ifdef CONFIG_NET_EMATCH in net/sched/cls_flow.c (latest git broken build)
[IPV4]: Fix compile error building without CONFIG_FS_PROC
...
In case a dcss segment cannot be loaded blk_cleanup_queue
will be called before blk_queue_make_request, leaving the
struct work unplug_work of the request queue uninitialized
before it is used.
That leads also to the lockdep message below.
To avoid that call blk_queue_make_request right after the
request_queue has been allocated.
This makes sure that the struct work is always initialized
before it is used.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 Not tainted 2.6.24 #6
Process swapper (pid: 1, task: 000000000f854038, ksp: 000000000f85f980)
040000000f85f860 000000000f85f880 0000000000000002 0000000000000000
000000000f85f920 000000000f85f898 000000000f85f898 000000000001622e
0000000000000000 000000000f85f980 0000000000000000 0000000000000000
000000000f85f880 000000000000000c 000000000f85f880 000000000f85f8f0
0000000000342908 000000000001622e 000000000f85f880 000000000f85f8d0
Call Trace:
([<000000000001619e>] show_trace+0xda/0x104)
[<0000000000016288>] show_stack+0xc0/0xf8
[<00000000000163d0>] dump_stack+0xb0/0xc0
[<000000000006e4ea>] __lock_acquire+0x47e/0x1160
[<000000000006f27c>] lock_acquire+0xb0/0xd8
[<000000000005a522>] __cancel_work_timer+0x9e/0x240
[<000000000005a72e>] cancel_work_sync+0x2a/0x3c
[<0000000000165c46>] kblockd_flush_work+0x26/0x34
[<0000000000169034>] blk_sync_queue+0x38/0x48
[<0000000000169080>] blk_release_queue+0x3c/0xa8
[<000000000017bce8>] kobject_cleanup+0x58/0xac
[<000000000017bd66>] kobject_release+0x2a/0x38
[<000000000017d28e>] kref_put+0x6e/0x94
[<000000000017bc80>] kobject_put+0x38/0x48
[<00000000001653be>] blk_put_queue+0x2a/0x38
[<0000000000168fee>] blk_cleanup_queue+0x82/0x90
[<0000000000213e7e>] dcssblk_add_store+0x34e/0x700
[<00000000005243b8>] dcssblk_init+0x1a0/0x308
[<000000000050a3c2>] kernel_init+0x1b2/0x3a4
[<000000000001ac82>] kernel_thread_starter+0x6/0xc
[<000000000001ac7c>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This requires making die() and die_if_kernel() return a value, and their
callers to honor this (and be prepared that it returns).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64] pci_sun4v.c: Section fixes.
Provide a way to use tc filters on vlan tag even if tag is buried in
skb due to hardware acceleration.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove BUILD_BUG_ON() in vmem code since it causes build failures if
the size of struct page increases. Instead calculate at compile time
the address of the highest physical address that can be added to the
1:1 mapping.
This supposed to fix a build failure with the page owner tracking leak
detector patches as reported by akpm.
page-owner-tracking-leak-detector-broken-on-s390.patch can be removed
from -mm again when this is merged.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Neither __cpu_down() nor __cpu_die() are being referenced without
CONFIG_HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: remove flush_agp_mappings calls from new flush handling code
intel-agp: introduce IS_I915 and do some cleanups..
[intel_agp] fix name for G35 chipset
intel-agp: fixup resource handling in flush code.
intel-agp: add new chipset ID
agp: remove unnecessary pci_dev_put
agp: remove uid comparison as security check
fix AGP warning
agp/intel: Add chipset flushing support for i8xx chipsets.
intel-agp: add chipset flushing support
agp: add chipset flushing support to AGP interface
WARNING: vmlinux.o(.text+0x39be4): Section mismatch in reference from the function probe_existing_entries() to the function .init.text:page_in_phys_avail()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if_addrlabel.h is needed for iproute2 usage.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under load the following bug message appeared while using sysrq-t:
BUG: scheduling while atomic: bash/3662/0x00000004
0000000000105b74 000000003ba17740 0000000000000002 0000000000000000
000000003ba177e0 000000003ba17758 000000003ba17758 0000000000105bfe
0000000000817ba8 000000003f2a5350 0000000000000000 0000000000000000
000000003ba17740 000000000000000c 000000003ba17740 000000003ba177b0
0000000000568630 0000000000105bfe 000000003ba17740 000000003ba17790
Call Trace:
([<0000000000105b74>] show_trace+0x13c/0x158)
[<0000000000105c58>] show_stack+0xc8/0xfc
[<0000000000105cbc>] dump_stack+0x30/0x40
[<000000000012a0c8>] __schedule_bug+0x84/0x94
[<000000000056234e>] schedule+0x5ea/0x970
[<0000000000477cd2>] __sclp_vt220_write+0x1f6/0x3ec
[<0000000000477f00>] sclp_vt220_con_write+0x38/0x48
[<0000000000130b4a>] __call_console_drivers+0xbe/0xd8
[<0000000000130bf0>] _call_console_drivers+0x8c/0xd0
[<0000000000130eea>] release_console_sem+0x1a6/0x2fc
[<0000000000131786>] vprintk+0x262/0x480
[<00000000001319fa>] printk+0x56/0x68
[<0000000000125aaa>] print_cfs_rq+0x45e/0x4a4
[<000000000012614e>] sched_debug_show+0x65e/0xee8
[<000000000012a8fc>] show_state_filter+0x1cc/0x1f0
[<000000000044d39c>] sysrq_handle_showstate+0x2c/0x3c
[<000000000044d1fe>] __handle_sysrq+0xae/0x18c
[<00000000002001f2>] write_sysrq_trigger+0x8a/0x90
[<00000000001f7862>] proc_reg_write+0x9a/0xc4
[<00000000001a83d4>] vfs_write+0xb8/0x174
[<00000000001a8b88>] sys_write+0x58/0x8c
[<0000000000112e7c>] sysc_noemu+0x10/0x16
[<0000020000116f68>] 0x20000116f68
The problem seems to be, that with a full console buffer, release_console_sem
disables interrupts with spin_lock_irqsave and then calls the console function
without enabling interrupts. __sclp_vt220_write checks for in_interrupt, to
decide if it can schedule. It should check for in_atomic instead.
The same is true for sclp_tty.c.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Anthony and Xiantao are working on KVM for ia64.
Signed-off-by Anthony Xu <anthony.xu@intel.com>
Signed-off-by Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add a driver for NetEffect RNICs
IB/mthca: Return proper error codes from mthca_fmr_alloc()
IB: Avoid marking __devinitdata as const
IB/mlx4: Actually print out the driver version
IB/ib_mthca: Pre-link receive WQEs in Tavor mode
IB/mthca: Remove checks for srq->first_free < 0
IB/fmr_pool: Allocate page list for pool FMRs only when caching enabled
IB/srp: Retry stale connections
mlx4_core: Don't read reserved fields in mlx4_QUERY_ADAPTER()
IB/mthca: Don't read reserved fields in mthca_QUERY_ADAPTER()
IPoIB: Remove a misleading debug print
IPoIB: Handle bonding failover race for connected neighbours too
IB/mthca: Fix and simplify page size calculation in mthca_reg_phys_mr()
IB/ehca: Add PMA support
IB/ehca: Update sma_attr also in case of disruptive config change
IB/ehca: Prevent sending UD packets to QP0
IB/cm: Add interim support for routed paths
mlx4_core: Fix more section mismatches
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
This patch removes the following no longer used functions:
- rtattr_parse()
- rtattr_strlcpy()
- __rtattr_parse_nested_compat()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an alias device is set offline while it is in use this may
result in a panic in the cleanup part of the dasd_block_tasklet.
The problem here is that there may exist some ccw requests that were
originally created for the alias device and transferred to the base
device when the alias was set offline. When these request are
cleaned up later, the discipline pointer in the alias device may not
be valid anymore. To fix this use the base device discipline to find
the cleanup function.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The only in kernel use of ia64_set_psr() needs to follow
it with a srlz.i (since it is changing state for PSR.ic).
So it is pointless to issue srlz.d inside this function.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Also fixed the include syntax while I was there.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a standard NIC and RDMA/iWARP driver for NetEffect 1/10Gb ethernet adapters.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new IS_I915 and also do some checkpatch whitespace cleanups.
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'slub-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
Explain kmem_cache_cpu fields
SLUB: Do not upset lockdep
SLUB: Fix coding style violations
Add parameter to add_partial to avoid having two functions
SLUB: rename defrag to remote_node_defrag_ratio
Move count_partial before kmem_cache_shrink
SLUB: Fix sysfs refcounting
slub: fix shadowed variable sparse warnings
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
Somewhere along the development of my ICMP relookup patch the header
length check went AWOL on the non-IPsec path. This patch restores the
check.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding interface control check (ifcc) handling in error recovery.
First retry up to 255 times and if all retries fail try an alternate
path if possible.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since kvm/module needs to use some unexported functions in kernel,
so export them with this patch.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Redo the calculation of NR_syscalls since that disappeared from i386 and
use a similar mechanism on x86_64.
We now figure out the size of the system call table in arch code and stick
that in syscall_table_size. arch/um/kernel/skas/syscall.c defines
NR_syscalls in terms of that since its the only thing that needs to know
how many system calls there are.
The old mechananism that was used on x86_64 is gone.
arch/um/include/sysdep-i386/syscalls.h got some formatting since I was
looking at it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the allocation of the MTT or the mailbox failed, mthca_fmr_alloc()
would return 0 (success) no matter what. This leads to crashes a
little down the road, when we try to dereference eg mr->mtt, which was
really ERR_PTR(-Ewhatever).
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change origin chipset name i965G_1 to market name G35.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (78 commits)
x86: fix RTC lockdep warning: potential hardirq recursion
x86: cpa, micro-optimization
x86: cpa, clean up code flow
x86: cpa, eliminate CPA_ enum
x86: cpa, cleanups
x86: implement gbpages support in change_page_attr()
x86: support gbpages in pagetable dump
x86: add gbpages support to lookup_address
x86: add pgtable accessor functions for gbpages
x86: add PUD_PAGE_SIZE
x86: add feature macros for the gbpages cpuid bit
x86: switch direct mapping setup over to set_pte
x86: fix page-present check in cpa_flush_range
x86: remove cpa warning
x86: remove now unused clear_kernel_mapping
x86: switch pci-gart over to using set_memory_np() instead of clear_kernel_mapping()
x86: cpa selftest, skip non present entries
x86: CPA fix pagetable split
x86: rename LARGE_PAGE_SIZE to PMD_PAGE_SIZE
x86: cpa, fix lookup_address
...
Add some comments explaining the fields of the kmem_cache_cpu structure.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix typo and remove vague comment
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file and remove
superfluous header includes.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Warning message :
WARNING: vmlinux.o(.text+0x9afc): Section mismatch: reference to .init.text:sa1110_mb_enable (between 'sa1111_probe' and 'sa1111_remove')
WARNING: vmlinux.o(.text+0x13b1ac): Section mismatch: reference to .init.text:pcmcia_jornada720_init (between 'pcmcia_probe' and 'pcmcia_remove')
* fixes the 'section mismatch' building warnings for target sa1100. Solution is __init -> __devinit. Thanks to Randy Dunlap for pointing out the solution.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a PXA2xx specific header file to control chip setup.
Without, the PCM027 BSP can't be built.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The port offset calculations depend on the protocol family, but, as
Adrian noticed, I broke this logic with the commit
5ee31fc1ecdcbc234c8c56dcacef87c8e09909d8
[INET]: Consolidate inet(6)_hash_connect.
Return this logic back, by passing the port offset directly into the
consolidated function.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Noticed-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Holger Wolf <wolf@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Unified changelog, 80 columns rule, and address form fix.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tweak the UML defconfig -
we probably don't need 256 old-style ptys - this slows down udev
noticably
enable hostfs
disable slab debugging - another noticable performance hit
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The flush code resource handling was having problems where some BIOS
reserve the resource in a pnp block and some don't.
Also there was a bug in that configure was being called at resume
and resetting some of the structs.
Signed-off-by: Dave Airlie <airlied@linux.ie>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
After disabling both CONFIG_DEBUG_LOCKING_API_SELFTESTS and netconsole
(using current mainline) I get a login prompt, and also...
[ 5.181668] SELinux: policy loaded with handle_unknown=deny
[ 5.183315] type=1403 audit(1202100038.157:3): policy loaded auid=4294967295 ses=4294967295
[ 5.822073] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[ 7.819146] ------------[ cut here ]------------
[ 7.819146] WARNING: at kernel/lockdep.c:2033 trace_hardirqs_on+0x9b/0x10d()
[ 7.819146] Modules linked in: generic ext3 jbd ide_disk ide_core
[ 7.819146] Pid: 399, comm: hwclock Not tainted 2.6.24 #4
[ 7.819146] [<c011d140>] warn_on_slowpath+0x41/0x51
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c013770c>] ? check_usage_forwards+0x19/0x3b
[ 7.819146] [<c01390c4>] ? __lock_acquire+0xac3/0xb0b
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c030ca6c>] ? _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c013848b>] trace_hardirqs_on+0x9b/0x10d
[ 7.819146] [<c030ca6c>] _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c011481e>] hpet_rtc_interrupt+0xdf/0x290
[ 7.819146] [<c014ea90>] handle_IRQ_event+0x1a/0x46
[ 7.819146] [<c014f8ea>] handle_edge_irq+0xbe/0xff
[ 7.819146] [<c0106e08>] do_IRQ+0x6d/0x84
[ 7.819146] [<c0105596>] common_interrupt+0x2e/0x34
[ 7.819146] [<c013007b>] ? ktime_get_ts+0x8/0x3f
[ 7.819146] [<c0139420>] ? lock_release+0x167/0x16f
[ 7.819146] [<c017974a>] ? core_sys_select+0x2c/0x327
[ 7.819146] [<c0179792>] core_sys_select+0x74/0x327
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c030ca6c>] ? _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c01384d6>] ? trace_hardirqs_on+0xe6/0x10d
[ 7.819146] [<c030ca77>] ? _spin_unlock_irq+0x2d/0x42
[ 7.819146] [<c023b437>] ? rtc_do_ioctl+0x11b/0x677
[ 7.819146] [<c01c487e>] ? inode_has_perm+0x5e/0x68
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01c490b>] ? file_has_perm+0x83/0x8c
[ 7.819146] [<c023ba08>] ? rtc_ioctl+0xf/0x11
[ 7.819146] [<c017898d>] ? do_ioctl+0x55/0x67
[ 7.819146] [<c0179d15>] sys_select+0x93/0x163
[ 7.819146] [<c0104b39>] ? sysenter_past_esp+0x9a/0xa5
[ 7.819146] [<c0104afe>] sysenter_past_esp+0x5f/0xa5
[ 7.819146] =======================
[ 7.819146] ---[ end trace 96540ca301ffb84c ]---
[ 7.819210] rtc: lost 6 interrupts
[ 7.870668] type=1400 audit(1202128840.794:4): avc: denied { audit_write } for pid=399 comm="hwclock" capability=29 scontext=system_u:system_r:hwclock_t:s0 tcontext=system_u:system_r:hwclock_t:s0 tclass=capability
[ 9.538866] input: PC Speaker as /class/input/input5
Because hpet_rtc_interrupt()'s call to get_rtc_time() ends up
resolving to include/asm-generic/rtc.h's (hilariously inlined)
get_rtc_time(), which does spin_unlock_irq() from hard IRQ context.
The obvious patch fixes it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
inconsistent {softirq-on-W} -> {in-softirq-W} usage.
swapper/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
(&n->list_lock){-+..}, at: [<ffffffff802935c1>] add_partial+0x31/0xa0
{softirq-on-W} state was registered at:
[<ffffffff80259fb8>] __lock_acquire+0x3e8/0x1140
[<ffffffff80259838>] debug_check_no_locks_freed+0x188/0x1a0
[<ffffffff8025ad65>] lock_acquire+0x55/0x70
[<ffffffff802935c1>] add_partial+0x31/0xa0
[<ffffffff805c76de>] _spin_lock+0x1e/0x30
[<ffffffff802935c1>] add_partial+0x31/0xa0
[<ffffffff80296f9c>] kmem_cache_open+0x1cc/0x330
[<ffffffff805c7984>] _spin_unlock_irq+0x24/0x30
[<ffffffff802974f4>] create_kmalloc_cache+0x64/0xf0
[<ffffffff80295640>] init_alloc_cpu_cpu+0x70/0x90
[<ffffffff8080ada5>] kmem_cache_init+0x65/0x1d0
[<ffffffff807f1b4e>] start_kernel+0x23e/0x350
[<ffffffff807f112d>] _sinittext+0x12d/0x140
[<ffffffffffffffff>] 0xffffffffffffffff
This change isn't really necessary for correctness, but it prevents lockdep
from getting upset and then disabling itself.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file and remove
superfluous header includes.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move update_process_times() out from under xtime_lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
The is caused by the patch below:
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
It renamed the confusing get_hsync_len() to get_hsync_invperiod(), which
unfortunately leaves poodle.c un-modified.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] make pfm_get_task work with virtual pids
[IA64] honor notify_die() returning NOTIFY_STOP
[IA64] remove dead code: __cpu_{down,die} from !HOTPLUG_CPU
[IA64] Appoint kvm/ia64 Maintainers
[IA64] ia64_set_psr should use srlz.i
[IA64] Export three symbols for module use
[IA64] mca style cleanup
[IA64] sn_hwperf semaphore to mutex
[IA64] generalize attribute of fsyscall_gtod_data
[IA64] efi.c Add /* never reached */ annotation
[IA64] efi.c Spelling/punctuation fixes
[IA64] Make efi.c mostly fit in 80 columns
[IA64] aliasing-test: fix gcc warnings on non-ia64
[IA64] Slim-down __clear_bit_unlock
[IA64] Fix the order of atomic operations in restore_previous_kprobes on ia64
[IA64] constify function pointer tables
[IA64] fix userspace compile error in gcc_intrin.h
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] dcss: Initialize workqueue before using it.
[S390] Remove BUILD_BUG_ON() in vmem code.
[S390] sclp_tty/sclp_vt220: Fix scheduling while atomic
[S390] dasd: fix panic caused by alias device offline
[S390] dasd: add ifcc handling
[S390] latencytop s390 support.
[S390] Implement ext2_find_next_bit.
[S390] Cleanup & optimize bitops.
[S390] Define GENERIC_LOCKBREAK.
[S390] console: allow vt220 console to be the only console
[S390] Fix couple of section mismatches.
[S390] Fix smp_call_function_mask semantics.
[S390] Fix linker script.
[S390] DEBUG_PAGEALLOC support for s390.
[S390] cio: Add shutdown callback for ccwgroup.
[S390] cio: Update documentation.
[S390] cio: Clean up chsc response code handling.
[S390] cio: make sense id procedure work with partial hardware response
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[PKT_SCHED]: vlan tag match
[NET]: Add if_addrlabel.h to sanitized headers.
[NET] rtnetlink.c: remove no longer used functions
[ICMP]: Restore pskb_pull calls in receive function
[INET]: Fix accidentally broken inet(6)_hash_connect's port offset calculations.
[NET]: Remove further references to net-modules.txt
bluetooth rfcomm tty: destroy before tty_close()
bluetooth: blacklist another Broadcom BCM2035 device
drivers/bluetooth/btsdio.c: fix double-free
drivers/bluetooth/bpa10x.c: fix memleak
bluetooth: uninlining
bluetooth: hidp_process_hid_control remove unnecessary parameter dealing
tun: impossible to deassert IFF_ONE_QUEUE or IFF_NO_PI
hamradio: fix dmascc section mismatch
[SCTP]: Fix kernel panic while received AUTH chunk with BAD shared key identifier
[SCTP]: Fix kernel panic while received AUTH chunk while enabled auth
[IPV4]: Formatting fix for /proc/net/fib_trie.
[IPV6]: Fix sysctl compilation error.
[NET_SCHED]: Add #ifdef CONFIG_NET_EMATCH in net/sched/cls_flow.c (latest git broken build)
[IPV4]: Fix compile error building without CONFIG_FS_PROC
...
In case a dcss segment cannot be loaded blk_cleanup_queue
will be called before blk_queue_make_request, leaving the
struct work unplug_work of the request queue uninitialized
before it is used.
That leads also to the lockdep message below.
To avoid that call blk_queue_make_request right after the
request_queue has been allocated.
This makes sure that the struct work is always initialized
before it is used.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 Not tainted 2.6.24 #6
Process swapper (pid: 1, task: 000000000f854038, ksp: 000000000f85f980)
040000000f85f860 000000000f85f880 0000000000000002 0000000000000000
000000000f85f920 000000000f85f898 000000000f85f898 000000000001622e
0000000000000000 000000000f85f980 0000000000000000 0000000000000000
000000000f85f880 000000000000000c 000000000f85f880 000000000f85f8f0
0000000000342908 000000000001622e 000000000f85f880 000000000f85f8d0
Call Trace:
([<000000000001619e>] show_trace+0xda/0x104)
[<0000000000016288>] show_stack+0xc0/0xf8
[<00000000000163d0>] dump_stack+0xb0/0xc0
[<000000000006e4ea>] __lock_acquire+0x47e/0x1160
[<000000000006f27c>] lock_acquire+0xb0/0xd8
[<000000000005a522>] __cancel_work_timer+0x9e/0x240
[<000000000005a72e>] cancel_work_sync+0x2a/0x3c
[<0000000000165c46>] kblockd_flush_work+0x26/0x34
[<0000000000169034>] blk_sync_queue+0x38/0x48
[<0000000000169080>] blk_release_queue+0x3c/0xa8
[<000000000017bce8>] kobject_cleanup+0x58/0xac
[<000000000017bd66>] kobject_release+0x2a/0x38
[<000000000017d28e>] kref_put+0x6e/0x94
[<000000000017bc80>] kobject_put+0x38/0x48
[<00000000001653be>] blk_put_queue+0x2a/0x38
[<0000000000168fee>] blk_cleanup_queue+0x82/0x90
[<0000000000213e7e>] dcssblk_add_store+0x34e/0x700
[<00000000005243b8>] dcssblk_init+0x1a0/0x308
[<000000000050a3c2>] kernel_init+0x1b2/0x3a4
[<000000000001ac82>] kernel_thread_starter+0x6/0xc
[<000000000001ac7c>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove BUILD_BUG_ON() in vmem code since it causes build failures if
the size of struct page increases. Instead calculate at compile time
the address of the highest physical address that can be added to the
1:1 mapping.
This supposed to fix a build failure with the page owner tracking leak
detector patches as reported by akpm.
page-owner-tracking-leak-detector-broken-on-s390.patch can be removed
from -mm again when this is merged.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: remove flush_agp_mappings calls from new flush handling code
intel-agp: introduce IS_I915 and do some cleanups..
[intel_agp] fix name for G35 chipset
intel-agp: fixup resource handling in flush code.
intel-agp: add new chipset ID
agp: remove unnecessary pci_dev_put
agp: remove uid comparison as security check
fix AGP warning
agp/intel: Add chipset flushing support for i8xx chipsets.
intel-agp: add chipset flushing support
agp: add chipset flushing support to AGP interface
WARNING: vmlinux.o(.text+0x39be4): Section mismatch in reference from the function probe_existing_entries() to the function .init.text:page_in_phys_avail()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under load the following bug message appeared while using sysrq-t:
BUG: scheduling while atomic: bash/3662/0x00000004
0000000000105b74 000000003ba17740 0000000000000002 0000000000000000
000000003ba177e0 000000003ba17758 000000003ba17758 0000000000105bfe
0000000000817ba8 000000003f2a5350 0000000000000000 0000000000000000
000000003ba17740 000000000000000c 000000003ba17740 000000003ba177b0
0000000000568630 0000000000105bfe 000000003ba17740 000000003ba17790
Call Trace:
([<0000000000105b74>] show_trace+0x13c/0x158)
[<0000000000105c58>] show_stack+0xc8/0xfc
[<0000000000105cbc>] dump_stack+0x30/0x40
[<000000000012a0c8>] __schedule_bug+0x84/0x94
[<000000000056234e>] schedule+0x5ea/0x970
[<0000000000477cd2>] __sclp_vt220_write+0x1f6/0x3ec
[<0000000000477f00>] sclp_vt220_con_write+0x38/0x48
[<0000000000130b4a>] __call_console_drivers+0xbe/0xd8
[<0000000000130bf0>] _call_console_drivers+0x8c/0xd0
[<0000000000130eea>] release_console_sem+0x1a6/0x2fc
[<0000000000131786>] vprintk+0x262/0x480
[<00000000001319fa>] printk+0x56/0x68
[<0000000000125aaa>] print_cfs_rq+0x45e/0x4a4
[<000000000012614e>] sched_debug_show+0x65e/0xee8
[<000000000012a8fc>] show_state_filter+0x1cc/0x1f0
[<000000000044d39c>] sysrq_handle_showstate+0x2c/0x3c
[<000000000044d1fe>] __handle_sysrq+0xae/0x18c
[<00000000002001f2>] write_sysrq_trigger+0x8a/0x90
[<00000000001f7862>] proc_reg_write+0x9a/0xc4
[<00000000001a83d4>] vfs_write+0xb8/0x174
[<00000000001a8b88>] sys_write+0x58/0x8c
[<0000000000112e7c>] sysc_noemu+0x10/0x16
[<0000020000116f68>] 0x20000116f68
The problem seems to be, that with a full console buffer, release_console_sem
disables interrupts with spin_lock_irqsave and then calls the console function
without enabling interrupts. __sclp_vt220_write checks for in_interrupt, to
decide if it can schedule. It should check for in_atomic instead.
The same is true for sclp_tty.c.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add a driver for NetEffect RNICs
IB/mthca: Return proper error codes from mthca_fmr_alloc()
IB: Avoid marking __devinitdata as const
IB/mlx4: Actually print out the driver version
IB/ib_mthca: Pre-link receive WQEs in Tavor mode
IB/mthca: Remove checks for srq->first_free < 0
IB/fmr_pool: Allocate page list for pool FMRs only when caching enabled
IB/srp: Retry stale connections
mlx4_core: Don't read reserved fields in mlx4_QUERY_ADAPTER()
IB/mthca: Don't read reserved fields in mthca_QUERY_ADAPTER()
IPoIB: Remove a misleading debug print
IPoIB: Handle bonding failover race for connected neighbours too
IB/mthca: Fix and simplify page size calculation in mthca_reg_phys_mr()
IB/ehca: Add PMA support
IB/ehca: Update sma_attr also in case of disruptive config change
IB/ehca: Prevent sending UD packets to QP0
IB/cm: Add interim support for routed paths
mlx4_core: Fix more section mismatches
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
When an alias device is set offline while it is in use this may
result in a panic in the cleanup part of the dasd_block_tasklet.
The problem here is that there may exist some ccw requests that were
originally created for the alias device and transferred to the base
device when the alias was set offline. When these request are
cleaned up later, the discipline pointer in the alias device may not
be valid anymore. To fix this use the base device discipline to find
the cleanup function.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'slub-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
Explain kmem_cache_cpu fields
SLUB: Do not upset lockdep
SLUB: Fix coding style violations
Add parameter to add_partial to avoid having two functions
SLUB: rename defrag to remote_node_defrag_ratio
Move count_partial before kmem_cache_shrink
SLUB: Fix sysfs refcounting
slub: fix shadowed variable sparse warnings
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
Redo the calculation of NR_syscalls since that disappeared from i386 and
use a similar mechanism on x86_64.
We now figure out the size of the system call table in arch code and stick
that in syscall_table_size. arch/um/kernel/skas/syscall.c defines
NR_syscalls in terms of that since its the only thing that needs to know
how many system calls there are.
The old mechananism that was used on x86_64 is gone.
arch/um/include/sysdep-i386/syscalls.h got some formatting since I was
looking at it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the allocation of the MTT or the mailbox failed, mthca_fmr_alloc()
would return 0 (success) no matter what. This leads to crashes a
little down the road, when we try to dereference eg mr->mtt, which was
really ERR_PTR(-Ewhatever).
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (78 commits)
x86: fix RTC lockdep warning: potential hardirq recursion
x86: cpa, micro-optimization
x86: cpa, clean up code flow
x86: cpa, eliminate CPA_ enum
x86: cpa, cleanups
x86: implement gbpages support in change_page_attr()
x86: support gbpages in pagetable dump
x86: add gbpages support to lookup_address
x86: add pgtable accessor functions for gbpages
x86: add PUD_PAGE_SIZE
x86: add feature macros for the gbpages cpuid bit
x86: switch direct mapping setup over to set_pte
x86: fix page-present check in cpa_flush_range
x86: remove cpa warning
x86: remove now unused clear_kernel_mapping
x86: switch pci-gart over to using set_memory_np() instead of clear_kernel_mapping()
x86: cpa selftest, skip non present entries
x86: CPA fix pagetable split
x86: rename LARGE_PAGE_SIZE to PMD_PAGE_SIZE
x86: cpa, fix lookup_address
...
Warning message :
WARNING: vmlinux.o(.text+0x9afc): Section mismatch: reference to .init.text:sa1110_mb_enable (between 'sa1111_probe' and 'sa1111_remove')
WARNING: vmlinux.o(.text+0x13b1ac): Section mismatch: reference to .init.text:pcmcia_jornada720_init (between 'pcmcia_probe' and 'pcmcia_remove')
* fixes the 'section mismatch' building warnings for target sa1100. Solution is __init -> __devinit. Thanks to Randy Dunlap for pointing out the solution.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The port offset calculations depend on the protocol family, but, as
Adrian noticed, I broke this logic with the commit
5ee31fc1ecdcbc234c8c56dcacef87c8e09909d8
[INET]: Consolidate inet(6)_hash_connect.
Return this logic back, by passing the port offset directly into the
consolidated function.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Noticed-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tweak the UML defconfig -
we probably don't need 256 old-style ptys - this slows down udev
noticably
enable hostfs
disable slab debugging - another noticable performance hit
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
After disabling both CONFIG_DEBUG_LOCKING_API_SELFTESTS and netconsole
(using current mainline) I get a login prompt, and also...
[ 5.181668] SELinux: policy loaded with handle_unknown=deny
[ 5.183315] type=1403 audit(1202100038.157:3): policy loaded auid=4294967295 ses=4294967295
[ 5.822073] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[ 7.819146] ------------[ cut here ]------------
[ 7.819146] WARNING: at kernel/lockdep.c:2033 trace_hardirqs_on+0x9b/0x10d()
[ 7.819146] Modules linked in: generic ext3 jbd ide_disk ide_core
[ 7.819146] Pid: 399, comm: hwclock Not tainted 2.6.24 #4
[ 7.819146] [<c011d140>] warn_on_slowpath+0x41/0x51
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c013770c>] ? check_usage_forwards+0x19/0x3b
[ 7.819146] [<c01390c4>] ? __lock_acquire+0xac3/0xb0b
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c030ca6c>] ? _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c013848b>] trace_hardirqs_on+0x9b/0x10d
[ 7.819146] [<c030ca6c>] _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c011481e>] hpet_rtc_interrupt+0xdf/0x290
[ 7.819146] [<c014ea90>] handle_IRQ_event+0x1a/0x46
[ 7.819146] [<c014f8ea>] handle_edge_irq+0xbe/0xff
[ 7.819146] [<c0106e08>] do_IRQ+0x6d/0x84
[ 7.819146] [<c0105596>] common_interrupt+0x2e/0x34
[ 7.819146] [<c013007b>] ? ktime_get_ts+0x8/0x3f
[ 7.819146] [<c0139420>] ? lock_release+0x167/0x16f
[ 7.819146] [<c017974a>] ? core_sys_select+0x2c/0x327
[ 7.819146] [<c0179792>] core_sys_select+0x74/0x327
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c030ca6c>] ? _spin_unlock_irq+0x22/0x42
[ 7.819146] [<c01384d6>] ? trace_hardirqs_on+0xe6/0x10d
[ 7.819146] [<c030ca77>] ? _spin_unlock_irq+0x2d/0x42
[ 7.819146] [<c023b437>] ? rtc_do_ioctl+0x11b/0x677
[ 7.819146] [<c01c487e>] ? inode_has_perm+0x5e/0x68
[ 7.819146] [<c01364a9>] ? lock_release_holdtime+0x50/0x56
[ 7.819146] [<c0108c98>] ? native_sched_clock+0x8b/0x9f
[ 7.819146] [<c01c490b>] ? file_has_perm+0x83/0x8c
[ 7.819146] [<c023ba08>] ? rtc_ioctl+0xf/0x11
[ 7.819146] [<c017898d>] ? do_ioctl+0x55/0x67
[ 7.819146] [<c0179d15>] sys_select+0x93/0x163
[ 7.819146] [<c0104b39>] ? sysenter_past_esp+0x9a/0xa5
[ 7.819146] [<c0104afe>] sysenter_past_esp+0x5f/0xa5
[ 7.819146] =======================
[ 7.819146] ---[ end trace 96540ca301ffb84c ]---
[ 7.819210] rtc: lost 6 interrupts
[ 7.870668] type=1400 audit(1202128840.794:4): avc: denied { audit_write } for pid=399 comm="hwclock" capability=29 scontext=system_u:system_r:hwclock_t:s0 tcontext=system_u:system_r:hwclock_t:s0 tclass=capability
[ 9.538866] input: PC Speaker as /class/input/input5
Because hpet_rtc_interrupt()'s call to get_rtc_time() ends up
resolving to include/asm-generic/rtc.h's (hilariously inlined)
get_rtc_time(), which does spin_unlock_irq() from hard IRQ context.
The obvious patch fixes it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
inconsistent {softirq-on-W} -> {in-softirq-W} usage.
swapper/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
(&n->list_lock){-+..}, at: [<ffffffff802935c1>] add_partial+0x31/0xa0
{softirq-on-W} state was registered at:
[<ffffffff80259fb8>] __lock_acquire+0x3e8/0x1140
[<ffffffff80259838>] debug_check_no_locks_freed+0x188/0x1a0
[<ffffffff8025ad65>] lock_acquire+0x55/0x70
[<ffffffff802935c1>] add_partial+0x31/0xa0
[<ffffffff805c76de>] _spin_lock+0x1e/0x30
[<ffffffff802935c1>] add_partial+0x31/0xa0
[<ffffffff80296f9c>] kmem_cache_open+0x1cc/0x330
[<ffffffff805c7984>] _spin_unlock_irq+0x24/0x30
[<ffffffff802974f4>] create_kmalloc_cache+0x64/0xf0
[<ffffffff80295640>] init_alloc_cpu_cpu+0x70/0x90
[<ffffffff8080ada5>] kmem_cache_init+0x65/0x1d0
[<ffffffff807f1b4e>] start_kernel+0x23e/0x350
[<ffffffff807f112d>] _sinittext+0x12d/0x140
[<ffffffffffffffff>] 0xffffffffffffffff
This change isn't really necessary for correctness, but it prevents lockdep
from getting upset and then disabling itself.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
The is caused by the patch below:
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
It renamed the confusing get_hsync_len() to get_hsync_invperiod(), which
unfortunately leaves poodle.c un-modified.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>