tjh.dev
Linux kernel mirror (for testing)
git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
kernel
os
linux
1# SPDX-License-Identifier: GPL-2.0
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/net/ethernet-phy.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Ethernet PHY Common Properties
8
9maintainers:
10 - Andrew Lunn <andrew@lunn.ch>
11 - Florian Fainelli <f.fainelli@gmail.com>
12 - Heiner Kallweit <hkallweit1@gmail.com>
13
14# The dt-schema tools will generate a select statement first by using
15# the compatible, and second by using the node name if any. In our
16# case, the node name is the one we want to match on, while the
17# compatible is optional.
18select:
19 properties:
20 $nodename:
21 pattern: "^ethernet-phy(@[a-f0-9]+)?$"
22
23 required:
24 - $nodename
25
26properties:
27 $nodename:
28 pattern: "^ethernet-phy(@[a-f0-9]+)?$"
29
30 compatible:
31 oneOf:
32 - const: ethernet-phy-ieee802.3-c22
33 description: PHYs that implement IEEE802.3 clause 22
34 - const: ethernet-phy-ieee802.3-c45
35 description: PHYs that implement IEEE802.3 clause 45
36 - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
37 description:
38 If the PHY reports an incorrect ID (or none at all) then the
39 compatible list may contain an entry with the correct PHY ID
40 in the above form.
41 The first group of digits is the 16 bit Phy Identifier 1
42 register, this is the chip vendor OUI bits 3:18. The
43 second group of digits is the Phy Identifier 2 register,
44 this is the chip vendor OUI bits 19:24, followed by 10
45 bits of a vendor specific ID.
46 - items:
47 - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
48 - const: ethernet-phy-ieee802.3-c22
49 - items:
50 - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
51 - const: ethernet-phy-ieee802.3-c45
52
53 reg:
54 minimum: 0
55 maximum: 31
56 description:
57 The ID number for the PHY.
58
59 interrupts:
60 maxItems: 1
61
62 max-speed:
63 enum:
64 - 10
65 - 100
66 - 1000
67 - 2500
68 - 5000
69 - 10000
70 - 20000
71 - 25000
72 - 40000
73 - 50000
74 - 56000
75 - 100000
76 - 200000
77 description:
78 Maximum PHY supported speed in Mbits / seconds.
79
80 phy-10base-t1l-2.4vpp:
81 description: |
82 tristate, request/disable 2.4 Vpp operating mode. The values are:
83 0: Disable 2.4 Vpp operating mode.
84 1: Request 2.4 Vpp operating mode from link partner.
85 Absence of this property will leave configuration to default values.
86 $ref: /schemas/types.yaml#/definitions/uint32
87 enum: [0, 1]
88
89 broken-turn-around:
90 $ref: /schemas/types.yaml#/definitions/flag
91 description:
92 If set, indicates the PHY device does not correctly release
93 the turn around line low at end of the control phase of the
94 MDIO transaction.
95
96 brr-mode:
97 $ref: /schemas/types.yaml#/definitions/flag
98 description:
99 If set, indicates the network cable interface is an alternative one as
100 defined in the BroadR-Reach link mode specification under 1BR-100 and
101 1BR-10 names. The PHY must be configured to operate in BroadR-Reach mode
102 by software.
103
104 clocks:
105 maxItems: 1
106 description:
107 External clock connected to the PHY. If not specified it is assumed
108 that the PHY uses a fixed crystal or an internal oscillator.
109
110 enet-phy-lane-swap:
111 $ref: /schemas/types.yaml#/definitions/flag
112 description:
113 If set, indicates the PHY will swap the TX/RX lanes to
114 compensate for the board being designed with the lanes
115 swapped.
116
117 enet-phy-lane-no-swap:
118 $ref: /schemas/types.yaml#/definitions/flag
119 description:
120 If set, indicates that PHY will disable swap of the
121 TX/RX lanes. This property allows the PHY to work correctly after
122 e.g. wrong bootstrap configuration caused by issues in PCB
123 layout design.
124
125 eee-broken-100tx:
126 $ref: /schemas/types.yaml#/definitions/flag
127 description:
128 Mark the corresponding energy efficient ethernet mode as
129 broken and request the ethernet to stop advertising it.
130
131 eee-broken-1000t:
132 $ref: /schemas/types.yaml#/definitions/flag
133 description:
134 Mark the corresponding energy efficient ethernet mode as
135 broken and request the ethernet to stop advertising it.
136
137 eee-broken-10gt:
138 $ref: /schemas/types.yaml#/definitions/flag
139 description:
140 Mark the corresponding energy efficient ethernet mode as
141 broken and request the ethernet to stop advertising it.
142
143 eee-broken-1000kx:
144 $ref: /schemas/types.yaml#/definitions/flag
145 description:
146 Mark the corresponding energy efficient ethernet mode as
147 broken and request the ethernet to stop advertising it.
148
149 eee-broken-10gkx4:
150 $ref: /schemas/types.yaml#/definitions/flag
151 description:
152 Mark the corresponding energy efficient ethernet mode as
153 broken and request the ethernet to stop advertising it.
154
155 eee-broken-10gkr:
156 $ref: /schemas/types.yaml#/definitions/flag
157 description:
158 Mark the corresponding energy efficient ethernet mode as
159 broken and request the ethernet to stop advertising it.
160
161 timing-role:
162 $ref: /schemas/types.yaml#/definitions/string
163 enum:
164 - forced-master
165 - forced-slave
166 - preferred-master
167 - preferred-slave
168 description: |
169 Specifies the timing role of the PHY in the network link. This property is
170 required for setups where the role must be explicitly assigned via the
171 device tree due to limitations in hardware strapping or incorrect strap
172 configurations.
173 It is applicable to Single Pair Ethernet (1000/100/10Base-T1) and other
174 PHY types, including 1000Base-T, where it controls whether the PHY should
175 be a master (clock source) or a slave (clock receiver).
176
177 - 'forced-master': The PHY is forced to operate as a master.
178 - 'forced-slave': The PHY is forced to operate as a slave.
179 - 'preferred-master': Prefer the PHY to be master but allow negotiation.
180 - 'preferred-slave': Prefer the PHY to be slave but allow negotiation.
181
182 pses:
183 $ref: /schemas/types.yaml#/definitions/phandle-array
184 maxItems: 1
185 description:
186 Specifies a reference to a node representing a Power Sourcing Equipment.
187
188 phy-is-integrated:
189 $ref: /schemas/types.yaml#/definitions/flag
190 description:
191 If set, indicates that the PHY is integrated into the same
192 physical package as the Ethernet MAC. If needed, muxers
193 should be configured to ensure the integrated PHY is
194 used. The absence of this property indicates the muxers
195 should be configured so that the external PHY is used.
196
197 resets:
198 maxItems: 1
199
200 reset-names:
201 const: phy
202
203 reset-gpios:
204 maxItems: 1
205 description:
206 The GPIO phandle and specifier for the PHY reset signal.
207
208 reset-assert-us:
209 description:
210 Delay after the reset was asserted in microseconds. If this
211 property is missing the delay will be skipped.
212
213 reset-deassert-us:
214 description:
215 Delay after the reset was deasserted in microseconds. If
216 this property is missing the delay will be skipped.
217
218 sfp:
219 $ref: /schemas/types.yaml#/definitions/phandle
220 description:
221 Specifies a reference to a node representing a SFP cage.
222
223 rx-internal-delay-ps:
224 description: |
225 RGMII Receive PHY Clock Delay defined in pico seconds. This is used for
226 PHY's that have configurable RX internal delays. If this property is
227 present then the PHY applies the RX delay.
228
229 tx-internal-delay-ps:
230 description: |
231 RGMII Transmit PHY Clock Delay defined in pico seconds. This is used for
232 PHY's that have configurable TX internal delays. If this property is
233 present then the PHY applies the TX delay.
234
235 leds:
236 type: object
237
238 properties:
239 '#address-cells':
240 const: 1
241
242 '#size-cells':
243 const: 0
244
245 patternProperties:
246 '^led@[a-f0-9]+$':
247 $ref: /schemas/leds/common.yaml#
248
249 properties:
250 reg:
251 maxItems: 1
252 description:
253 This define the LED index in the PHY or the MAC. It's really
254 driver dependent and required for ports that define multiple
255 LED for the same port.
256
257 required:
258 - reg
259
260 unevaluatedProperties: false
261
262 additionalProperties: false
263
264required:
265 - reg
266
267additionalProperties: true
268
269examples:
270 - |
271 #include <dt-bindings/leds/common.h>
272
273 ethernet {
274 #address-cells = <1>;
275 #size-cells = <0>;
276
277 ethernet-phy@0 {
278 compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c45";
279 interrupt-parent = <&PIC>;
280 interrupts = <35 1>;
281 reg = <0>;
282
283 resets = <&rst 8>;
284 reset-names = "phy";
285 reset-gpios = <&gpio1 4 1>;
286 reset-assert-us = <1000>;
287 reset-deassert-us = <2000>;
288
289 leds {
290 #address-cells = <1>;
291 #size-cells = <0>;
292
293 led@0 {
294 reg = <0>;
295 color = <LED_COLOR_ID_WHITE>;
296 function = LED_FUNCTION_LAN;
297 default-state = "keep";
298 };
299 };
300 };
301 };