tjh.dev
Linux kernel mirror (for testing)
git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
kernel
os
linux
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Copyright (C) 2018 Marvell
4 *
5 * Authors:
6 * Evan Wang <xswang@marvell.com>
7 * Miquèl Raynal <miquel.raynal@bootlin.com>
8 * Pali Rohár <pali@kernel.org>
9 * Marek Behún <kabel@kernel.org>
10 *
11 * Structure inspired from phy-mvebu-cp110-comphy.c written by Antoine Tenart.
12 * Comphy code from ARM Trusted Firmware ported by Pali Rohár <pali@kernel.org>
13 * and Marek Behún <kabel@kernel.org>.
14 */
15
16#include <linux/bitfield.h>
17#include <linux/clk.h>
18#include <linux/io.h>
19#include <linux/iopoll.h>
20#include <linux/mfd/syscon.h>
21#include <linux/module.h>
22#include <linux/phy.h>
23#include <linux/phy/phy.h>
24#include <linux/platform_device.h>
25#include <linux/spinlock.h>
26
27#define PLL_SET_DELAY_US 600
28#define COMPHY_PLL_SLEEP 1000
29#define COMPHY_PLL_TIMEOUT 150000
30
31/* Comphy lane2 indirect access register offset */
32#define COMPHY_LANE2_INDIR_ADDR 0x0
33#define COMPHY_LANE2_INDIR_DATA 0x4
34
35/* SATA and USB3 PHY offset compared to SATA PHY */
36#define COMPHY_LANE2_REGS_BASE 0x200
37
38/*
39 * When accessing common PHY lane registers directly, we need to shift by 1,
40 * since the registers are 16-bit.
41 */
42#define COMPHY_LANE_REG_DIRECT(reg) (((reg) & 0x7FF) << 1)
43
44/* COMPHY registers */
45#define COMPHY_POWER_PLL_CTRL 0x01
46#define PU_IVREF_BIT BIT(15)
47#define PU_PLL_BIT BIT(14)
48#define PU_RX_BIT BIT(13)
49#define PU_TX_BIT BIT(12)
50#define PU_TX_INTP_BIT BIT(11)
51#define PU_DFE_BIT BIT(10)
52#define RESET_DTL_RX_BIT BIT(9)
53#define PLL_LOCK_BIT BIT(8)
54#define REF_FREF_SEL_MASK GENMASK(4, 0)
55#define REF_FREF_SEL_SERDES_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x1)
56#define REF_FREF_SEL_SERDES_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
57#define REF_FREF_SEL_SERDES_50MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x4)
58#define REF_FREF_SEL_PCIE_USB3_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x2)
59#define REF_FREF_SEL_PCIE_USB3_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
60#define COMPHY_MODE_MASK GENMASK(7, 5)
61#define COMPHY_MODE_SATA FIELD_PREP(COMPHY_MODE_MASK, 0x0)
62#define COMPHY_MODE_PCIE FIELD_PREP(COMPHY_MODE_MASK, 0x3)
63#define COMPHY_MODE_SERDES FIELD_PREP(COMPHY_MODE_MASK, 0x4)
64#define COMPHY_MODE_USB3 FIELD_PREP(COMPHY_MODE_MASK, 0x5)
65
66#define COMPHY_KVCO_CAL_CTRL 0x02
67#define USE_MAX_PLL_RATE_BIT BIT(12)
68#define SPEED_PLL_MASK GENMASK(7, 2)
69#define SPEED_PLL_VALUE_16 FIELD_PREP(SPEED_PLL_MASK, 0x10)
70
71#define COMPHY_DIG_LOOPBACK_EN 0x23
72#define SEL_DATA_WIDTH_MASK GENMASK(11, 10)
73#define DATA_WIDTH_10BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x0)
74#define DATA_WIDTH_20BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x1)
75#define DATA_WIDTH_40BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x2)
76#define PLL_READY_TX_BIT BIT(4)
77
78#define COMPHY_SYNC_PATTERN 0x24
79#define TXD_INVERT_BIT BIT(10)
80#define RXD_INVERT_BIT BIT(11)
81
82#define COMPHY_SYNC_MASK_GEN 0x25
83#define PHY_GEN_MAX_MASK GENMASK(11, 10)
84#define PHY_GEN_MAX_USB3_5G FIELD_PREP(PHY_GEN_MAX_MASK, 0x1)
85
86#define COMPHY_ISOLATION_CTRL 0x26
87#define PHY_ISOLATE_MODE BIT(15)
88
89#define COMPHY_GEN2_SET2 0x3e
90#define GS2_TX_SSC_AMP_MASK GENMASK(15, 9)
91#define GS2_TX_SSC_AMP_4128 FIELD_PREP(GS2_TX_SSC_AMP_MASK, 0x20)
92#define GS2_VREG_RXTX_MAS_ISET_MASK GENMASK(8, 7)
93#define GS2_VREG_RXTX_MAS_ISET_60U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
94 0x0)
95#define GS2_VREG_RXTX_MAS_ISET_80U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
96 0x1)
97#define GS2_VREG_RXTX_MAS_ISET_100U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
98 0x2)
99#define GS2_VREG_RXTX_MAS_ISET_120U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
100 0x3)
101#define GS2_RSVD_6_0_MASK GENMASK(6, 0)
102
103#define COMPHY_GEN3_SET2 0x3f
104
105#define COMPHY_IDLE_SYNC_EN 0x48
106#define IDLE_SYNC_EN BIT(12)
107
108#define COMPHY_MISC_CTRL0 0x4F
109#define CLK100M_125M_EN BIT(4)
110#define TXDCLK_2X_SEL BIT(6)
111#define CLK500M_EN BIT(7)
112#define PHY_REF_CLK_SEL BIT(10)
113
114#define COMPHY_SFT_RESET 0x52
115#define SFT_RST BIT(9)
116#define SFT_RST_NO_REG BIT(10)
117
118#define COMPHY_MISC_CTRL1 0x73
119#define SEL_BITS_PCIE_FORCE BIT(15)
120
121#define COMPHY_GEN2_SET3 0x112
122#define GS3_FFE_CAP_SEL_MASK GENMASK(3, 0)
123#define GS3_FFE_CAP_SEL_VALUE FIELD_PREP(GS3_FFE_CAP_SEL_MASK, 0xF)
124
125/* PIPE registers */
126#define COMPHY_PIPE_LANE_CFG0 0x180
127#define PRD_TXDEEMPH0_MASK BIT(0)
128#define PRD_TXMARGIN_MASK GENMASK(3, 1)
129#define PRD_TXSWING_MASK BIT(4)
130#define CFG_TX_ALIGN_POS_MASK GENMASK(8, 5)
131
132#define COMPHY_PIPE_LANE_CFG1 0x181
133#define PRD_TXDEEMPH1_MASK BIT(15)
134#define USE_MAX_PLL_RATE_EN BIT(9)
135#define TX_DET_RX_MODE BIT(6)
136#define GEN2_TX_DATA_DLY_MASK GENMASK(4, 3)
137#define GEN2_TX_DATA_DLY_DEFT FIELD_PREP(GEN2_TX_DATA_DLY_MASK, 2)
138#define TX_ELEC_IDLE_MODE_EN BIT(0)
139
140#define COMPHY_PIPE_LANE_STAT1 0x183
141#define TXDCLK_PCLK_EN BIT(0)
142
143#define COMPHY_PIPE_LANE_CFG4 0x188
144#define SPREAD_SPECTRUM_CLK_EN BIT(7)
145
146#define COMPHY_PIPE_RST_CLK_CTRL 0x1C1
147#define PIPE_SOFT_RESET BIT(0)
148#define PIPE_REG_RESET BIT(1)
149#define MODE_CORE_CLK_FREQ_SEL BIT(9)
150#define MODE_PIPE_WIDTH_32 BIT(3)
151#define MODE_REFDIV_MASK GENMASK(5, 4)
152#define MODE_REFDIV_BY_4 FIELD_PREP(MODE_REFDIV_MASK, 0x2)
153
154#define COMPHY_PIPE_TEST_MODE_CTRL 0x1C2
155#define MODE_MARGIN_OVERRIDE BIT(2)
156
157#define COMPHY_PIPE_CLK_SRC_LO 0x1C3
158#define MODE_CLK_SRC BIT(0)
159#define BUNDLE_PERIOD_SEL BIT(1)
160#define BUNDLE_PERIOD_SCALE_MASK GENMASK(3, 2)
161#define BUNDLE_SAMPLE_CTRL BIT(4)
162#define PLL_READY_DLY_MASK GENMASK(7, 5)
163#define CFG_SEL_20B BIT(15)
164
165#define COMPHY_PIPE_PWR_MGM_TIM1 0x1D0
166#define CFG_PM_OSCCLK_WAIT_MASK GENMASK(15, 12)
167#define CFG_PM_RXDEN_WAIT_MASK GENMASK(11, 8)
168#define CFG_PM_RXDEN_WAIT_1_UNIT FIELD_PREP(CFG_PM_RXDEN_WAIT_MASK, 0x1)
169#define CFG_PM_RXDLOZ_WAIT_MASK GENMASK(7, 0)
170#define CFG_PM_RXDLOZ_WAIT_7_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0x7)
171#define CFG_PM_RXDLOZ_WAIT_12_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0xC)
172
173/*
174 * This register is not from PHY lane register space. It only exists in the
175 * indirect register space, before the actual PHY lane 2 registers. So the
176 * offset is absolute, not relative to COMPHY_LANE2_REGS_BASE.
177 * It is used only for SATA PHY initialization.
178 */
179#define COMPHY_RESERVED_REG 0x0E
180#define PHYCTRL_FRM_PIN_BIT BIT(13)
181
182/* South Bridge PHY Configuration Registers */
183#define COMPHY_PHY_REG(lane, reg) (((1 - (lane)) * 0x28) + ((reg) & 0x3f))
184
185/*
186 * lane0: USB3/GbE1 PHY Configuration 1
187 * lane1: PCIe/GbE0 PHY Configuration 1
188 * (used only by SGMII code)
189 */
190#define COMPHY_PHY_CFG1 0x0
191#define PIN_PU_IVREF_BIT BIT(1)
192#define PIN_RESET_CORE_BIT BIT(11)
193#define PIN_RESET_COMPHY_BIT BIT(12)
194#define PIN_PU_PLL_BIT BIT(16)
195#define PIN_PU_RX_BIT BIT(17)
196#define PIN_PU_TX_BIT BIT(18)
197#define PIN_TX_IDLE_BIT BIT(19)
198#define GEN_RX_SEL_MASK GENMASK(25, 22)
199#define GEN_RX_SEL_VALUE(val) FIELD_PREP(GEN_RX_SEL_MASK, (val))
200#define GEN_TX_SEL_MASK GENMASK(29, 26)
201#define GEN_TX_SEL_VALUE(val) FIELD_PREP(GEN_TX_SEL_MASK, (val))
202#define SERDES_SPEED_1_25_G 0x6
203#define SERDES_SPEED_3_125_G 0x8
204#define PHY_RX_INIT_BIT BIT(30)
205
206/*
207 * lane0: USB3/GbE1 PHY Status 1
208 * lane1: PCIe/GbE0 PHY Status 1
209 * (used only by SGMII code)
210 */
211#define COMPHY_PHY_STAT1 0x18
212#define PHY_RX_INIT_DONE_BIT BIT(0)
213#define PHY_PLL_READY_RX_BIT BIT(2)
214#define PHY_PLL_READY_TX_BIT BIT(3)
215
216/* PHY Selector */
217#define COMPHY_SELECTOR_PHY_REG 0xFC
218/* bit0: 0: Lane1 is GbE0; 1: Lane1 is PCIe */
219#define COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT BIT(0)
220/* bit4: 0: Lane0 is GbE1; 1: Lane0 is USB3 */
221#define COMPHY_SELECTOR_USB3_GBE1_SEL_BIT BIT(4)
222/* bit8: 0: Lane0 is USB3 instead of GbE1, Lane2 is SATA; 1: Lane2 is USB3 */
223#define COMPHY_SELECTOR_USB3_PHY_SEL_BIT BIT(8)
224
225struct mvebu_a3700_comphy_conf {
226 unsigned int lane;
227 enum phy_mode mode;
228 int submode;
229};
230
231#define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode) \
232 { \
233 .lane = _lane, \
234 .mode = _mode, \
235 .submode = _smode, \
236 }
237
238#define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode) \
239 MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA)
240
241#define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode) \
242 MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode)
243
244static const struct mvebu_a3700_comphy_conf mvebu_a3700_comphy_modes[] = {
245 /* lane 0 */
246 MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS),
247 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII),
248 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_1000BASEX),
249 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX),
250 /* lane 1 */
251 MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE),
252 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII),
253 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_1000BASEX),
254 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX),
255 /* lane 2 */
256 MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA),
257 MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS),
258};
259
260struct mvebu_a3700_comphy_priv {
261 void __iomem *comphy_regs;
262 void __iomem *lane0_phy_regs; /* USB3 and GbE1 */
263 void __iomem *lane1_phy_regs; /* PCIe and GbE0 */
264 void __iomem *lane2_phy_indirect; /* SATA and USB3 */
265 spinlock_t lock; /* for PHY selector access */
266 bool xtal_is_40m;
267};
268
269struct mvebu_a3700_comphy_lane {
270 struct mvebu_a3700_comphy_priv *priv;
271 struct device *dev;
272 unsigned int id;
273 enum phy_mode mode;
274 int submode;
275 bool invert_tx;
276 bool invert_rx;
277 bool needs_reset;
278};
279
280struct gbe_phy_init_data_fix {
281 u16 addr;
282 u16 value;
283};
284
285/* Changes to 40M1G25 mode data required for running 40M3G125 init mode */
286static struct gbe_phy_init_data_fix gbe_phy_init_fix[] = {
287 { 0x005, 0x07CC }, { 0x015, 0x0000 }, { 0x01B, 0x0000 },
288 { 0x01D, 0x0000 }, { 0x01E, 0x0000 }, { 0x01F, 0x0000 },
289 { 0x020, 0x0000 }, { 0x021, 0x0030 }, { 0x026, 0x0888 },
290 { 0x04D, 0x0152 }, { 0x04F, 0xA020 }, { 0x050, 0x07CC },
291 { 0x053, 0xE9CA }, { 0x055, 0xBD97 }, { 0x071, 0x3015 },
292 { 0x076, 0x03AA }, { 0x07C, 0x0FDF }, { 0x0C2, 0x3030 },
293 { 0x0C3, 0x8000 }, { 0x0E2, 0x5550 }, { 0x0E3, 0x12A4 },
294 { 0x0E4, 0x7D00 }, { 0x0E6, 0x0C83 }, { 0x101, 0xFCC0 },
295 { 0x104, 0x0C10 }
296};
297
298/* 40M1G25 mode init data */
299static u16 gbe_phy_init[512] = {
300 /* 0 1 2 3 4 5 6 7 */
301 /*-----------------------------------------------------------*/
302 /* 8 9 A B C D E F */
303 0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26, /* 00 */
304 0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52, /* 08 */
305 0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000, /* 10 */
306 0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF, /* 18 */
307 0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000, /* 20 */
308 0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, /* 28 */
309 0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */
310 0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100, /* 38 */
311 0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00, /* 40 */
312 0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A, /* 48 */
313 0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001, /* 50 */
314 0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF, /* 58 */
315 0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000, /* 60 */
316 0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002, /* 68 */
317 0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780, /* 70 */
318 0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000, /* 78 */
319 0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000, /* 80 */
320 0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210, /* 88 */
321 0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F, /* 90 */
322 0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651, /* 98 */
323 0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000, /* A0 */
324 0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* A8 */
325 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* B0 */
326 0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000, /* B8 */
327 0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003, /* C0 */
328 0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000, /* C8 */
329 0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00, /* D0 */
330 0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000, /* D8 */
331 0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541, /* E0 */
332 0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200, /* E8 */
333 0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000, /* F0 */
334 0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000, /* F8 */
335 0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000, /*100 */
336 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*108 */
337 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000, /*110 */
338 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*118 */
339 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*120 */
340 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*128 */
341 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*130 */
342 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*138 */
343 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*140 */
344 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*148 */
345 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*150 */
346 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*158 */
347 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*160 */
348 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*168 */
349 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*170 */
350 0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000, /*178 */
351 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*180 */
352 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*188 */
353 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*190 */
354 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*198 */
355 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A0 */
356 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A8 */
357 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B0 */
358 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B8 */
359 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C0 */
360 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C8 */
361 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D0 */
362 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D8 */
363 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E0 */
364 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E8 */
365 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1F0 */
366 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 /*1F8 */
367};
368
369static inline void comphy_reg_set(void __iomem *addr, u32 data, u32 mask)
370{
371 u32 val;
372
373 val = readl(addr);
374 val = (val & ~mask) | (data & mask);
375 writel(val, addr);
376}
377
378static inline void comphy_reg_set16(void __iomem *addr, u16 data, u16 mask)
379{
380 u16 val;
381
382 val = readw(addr);
383 val = (val & ~mask) | (data & mask);
384 writew(val, addr);
385}
386
387/* Used for accessing lane 2 registers (SATA/USB3 PHY) */
388static void comphy_set_indirect(struct mvebu_a3700_comphy_priv *priv,
389 u32 offset, u16 data, u16 mask)
390{
391 writel(offset,
392 priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_ADDR);
393 comphy_reg_set(priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_DATA,
394 data, mask);
395}
396
397static void comphy_lane_reg_set(struct mvebu_a3700_comphy_lane *lane,
398 u16 reg, u16 data, u16 mask)
399{
400 if (lane->id == 2) {
401 /* lane 2 PHY registers are accessed indirectly */
402 comphy_set_indirect(lane->priv,
403 reg + COMPHY_LANE2_REGS_BASE,
404 data, mask);
405 } else {
406 void __iomem *base = lane->id == 1 ?
407 lane->priv->lane1_phy_regs :
408 lane->priv->lane0_phy_regs;
409
410 comphy_reg_set16(base + COMPHY_LANE_REG_DIRECT(reg),
411 data, mask);
412 }
413}
414
415static int comphy_lane_reg_poll(struct mvebu_a3700_comphy_lane *lane,
416 u16 reg, u16 bits,
417 ulong sleep_us, ulong timeout_us)
418{
419 int ret;
420
421 if (lane->id == 2) {
422 u32 data;
423
424 /* lane 2 PHY registers are accessed indirectly */
425 writel(reg + COMPHY_LANE2_REGS_BASE,
426 lane->priv->lane2_phy_indirect +
427 COMPHY_LANE2_INDIR_ADDR);
428
429 ret = readl_poll_timeout(lane->priv->lane2_phy_indirect +
430 COMPHY_LANE2_INDIR_DATA,
431 data, (data & bits) == bits,
432 sleep_us, timeout_us);
433 } else {
434 void __iomem *base = lane->id == 1 ?
435 lane->priv->lane1_phy_regs :
436 lane->priv->lane0_phy_regs;
437 u16 data;
438
439 ret = readw_poll_timeout(base + COMPHY_LANE_REG_DIRECT(reg),
440 data, (data & bits) == bits,
441 sleep_us, timeout_us);
442 }
443
444 return ret;
445}
446
447static void comphy_periph_reg_set(struct mvebu_a3700_comphy_lane *lane,
448 u8 reg, u32 data, u32 mask)
449{
450 comphy_reg_set(lane->priv->comphy_regs + COMPHY_PHY_REG(lane->id, reg),
451 data, mask);
452}
453
454static int comphy_periph_reg_poll(struct mvebu_a3700_comphy_lane *lane,
455 u8 reg, u32 bits,
456 ulong sleep_us, ulong timeout_us)
457{
458 u32 data;
459
460 return readl_poll_timeout(lane->priv->comphy_regs +
461 COMPHY_PHY_REG(lane->id, reg),
462 data, (data & bits) == bits,
463 sleep_us, timeout_us);
464}
465
466/* PHY selector configures with corresponding modes */
467static int
468mvebu_a3700_comphy_set_phy_selector(struct mvebu_a3700_comphy_lane *lane)
469{
470 u32 old, new, clr = 0, set = 0;
471 unsigned long flags;
472
473 switch (lane->mode) {
474 case PHY_MODE_SATA:
475 /* SATA must be in Lane2 */
476 if (lane->id == 2)
477 clr = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
478 else
479 goto error;
480 break;
481
482 case PHY_MODE_ETHERNET:
483 if (lane->id == 0)
484 clr = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
485 else if (lane->id == 1)
486 clr = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
487 else
488 goto error;
489 break;
490
491 case PHY_MODE_USB_HOST_SS:
492 if (lane->id == 2)
493 set = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
494 else if (lane->id == 0)
495 set = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
496 else
497 goto error;
498 break;
499
500 case PHY_MODE_PCIE:
501 /* PCIE must be in Lane1 */
502 if (lane->id == 1)
503 set = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
504 else
505 goto error;
506 break;
507
508 default:
509 goto error;
510 }
511
512 spin_lock_irqsave(&lane->priv->lock, flags);
513
514 old = readl(lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
515 new = (old & ~clr) | set;
516 writel(new, lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
517
518 spin_unlock_irqrestore(&lane->priv->lock, flags);
519
520 dev_dbg(lane->dev,
521 "COMPHY[%d] mode[%d] changed PHY selector 0x%08x -> 0x%08x\n",
522 lane->id, lane->mode, old, new);
523
524 return 0;
525error:
526 dev_err(lane->dev, "COMPHY[%d] mode[%d] is invalid\n", lane->id,
527 lane->mode);
528 return -EINVAL;
529}
530
531static int
532mvebu_a3700_comphy_sata_power_on(struct mvebu_a3700_comphy_lane *lane)
533{
534 u32 mask, data, ref_clk;
535 int ret;
536
537 /* Configure phy selector for SATA */
538 ret = mvebu_a3700_comphy_set_phy_selector(lane);
539 if (ret)
540 return ret;
541
542 /* Clear phy isolation mode to make it work in normal mode */
543 comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
544 0x0, PHY_ISOLATE_MODE);
545
546 /* 0. Check the Polarity invert bits */
547 data = 0x0;
548 if (lane->invert_tx)
549 data |= TXD_INVERT_BIT;
550 if (lane->invert_rx)
551 data |= RXD_INVERT_BIT;
552 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
553 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
554
555 /* 1. Select 40-bit data width */
556 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
557 DATA_WIDTH_40BIT, SEL_DATA_WIDTH_MASK);
558
559 /* 2. Select reference clock(25M) and PHY mode (SATA) */
560 if (lane->priv->xtal_is_40m)
561 ref_clk = REF_FREF_SEL_SERDES_40MHZ;
562 else
563 ref_clk = REF_FREF_SEL_SERDES_25MHZ;
564
565 data = ref_clk | COMPHY_MODE_SATA;
566 mask = REF_FREF_SEL_MASK | COMPHY_MODE_MASK;
567 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
568
569 /* 3. Use maximum PLL rate (no power save) */
570 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
571 USE_MAX_PLL_RATE_BIT, USE_MAX_PLL_RATE_BIT);
572
573 /* 4. Reset reserved bit */
574 comphy_set_indirect(lane->priv, COMPHY_RESERVED_REG,
575 0x0, PHYCTRL_FRM_PIN_BIT);
576
577 /* 5. Set vendor-specific configuration (It is done in sata driver) */
578 /* XXX: in U-Boot below sequence was executed in this place, in Linux
579 * not. Now it is done only in U-Boot before this comphy
580 * initialization - tests shows that it works ok, but in case of any
581 * future problem it is left for reference.
582 * reg_set(MVEBU_REGS_BASE + 0xe00a0, 0, 0xffffffff);
583 * reg_set(MVEBU_REGS_BASE + 0xe00a4, BIT(6), BIT(6));
584 */
585
586 /* Wait for > 55 us to allow PLL be enabled */
587 udelay(PLL_SET_DELAY_US);
588
589 /* Polling status */
590 ret = comphy_lane_reg_poll(lane, COMPHY_DIG_LOOPBACK_EN,
591 PLL_READY_TX_BIT, COMPHY_PLL_SLEEP,
592 COMPHY_PLL_TIMEOUT);
593 if (ret)
594 dev_err(lane->dev, "Failed to lock SATA PLL\n");
595
596 return ret;
597}
598
599static void comphy_gbe_phy_init(struct mvebu_a3700_comphy_lane *lane,
600 bool is_1gbps)
601{
602 int addr, fix_idx;
603 u16 val;
604
605 fix_idx = 0;
606 for (addr = 0; addr < 512; addr++) {
607 /*
608 * All PHY register values are defined in full for 3.125Gbps
609 * SERDES speed. The values required for 1.25 Gbps are almost
610 * the same and only few registers should be "fixed" in
611 * comparison to 3.125 Gbps values. These register values are
612 * stored in "gbe_phy_init_fix" array.
613 */
614 if (!is_1gbps && gbe_phy_init_fix[fix_idx].addr == addr) {
615 /* Use new value */
616 val = gbe_phy_init_fix[fix_idx].value;
617 if (fix_idx < ARRAY_SIZE(gbe_phy_init_fix))
618 fix_idx++;
619 } else {
620 val = gbe_phy_init[addr];
621 }
622
623 comphy_lane_reg_set(lane, addr, val, 0xFFFF);
624 }
625}
626
627static int
628mvebu_a3700_comphy_ethernet_power_on(struct mvebu_a3700_comphy_lane *lane)
629{
630 u32 mask, data, speed_sel;
631 int ret;
632
633 /* Set selector */
634 ret = mvebu_a3700_comphy_set_phy_selector(lane);
635 if (ret)
636 return ret;
637
638 /*
639 * 1. Reset PHY by setting PHY input port PIN_RESET=1.
640 * 2. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep
641 * PHY TXP/TXN output to idle state during PHY initialization
642 * 3. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0.
643 */
644 data = PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT | PIN_RESET_COMPHY_BIT;
645 mask = data | PIN_RESET_CORE_BIT | PIN_PU_PLL_BIT | PIN_PU_RX_BIT |
646 PIN_PU_TX_BIT | PHY_RX_INIT_BIT;
647 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
648
649 /* 4. Release reset to the PHY by setting PIN_RESET=0. */
650 data = 0x0;
651 mask = PIN_RESET_COMPHY_BIT;
652 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
653
654 /*
655 * 5. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide COMPHY
656 * bit rate
657 */
658 switch (lane->submode) {
659 case PHY_INTERFACE_MODE_SGMII:
660 case PHY_INTERFACE_MODE_1000BASEX:
661 /* SGMII 1G, SerDes speed 1.25G */
662 speed_sel = SERDES_SPEED_1_25_G;
663 break;
664 case PHY_INTERFACE_MODE_2500BASEX:
665 /* 2500Base-X, SerDes speed 3.125G */
666 speed_sel = SERDES_SPEED_3_125_G;
667 break;
668 default:
669 /* Other rates are not supported */
670 dev_err(lane->dev,
671 "unsupported phy speed %d on comphy lane%d\n",
672 lane->submode, lane->id);
673 return -EINVAL;
674 }
675 data = GEN_RX_SEL_VALUE(speed_sel) | GEN_TX_SEL_VALUE(speed_sel);
676 mask = GEN_RX_SEL_MASK | GEN_TX_SEL_MASK;
677 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
678
679 /*
680 * 6. Wait 10mS for bandgap and reference clocks to stabilize; then
681 * start SW programming.
682 */
683 mdelay(10);
684
685 /* 7. Program COMPHY register PHY_MODE */
686 data = COMPHY_MODE_SERDES;
687 mask = COMPHY_MODE_MASK;
688 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
689
690 /*
691 * 8. Set COMPHY register REFCLK_SEL to select the correct REFCLK
692 * source
693 */
694 data = 0x0;
695 mask = PHY_REF_CLK_SEL;
696 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
697
698 /*
699 * 9. Set correct reference clock frequency in COMPHY register
700 * REF_FREF_SEL.
701 */
702 if (lane->priv->xtal_is_40m)
703 data = REF_FREF_SEL_SERDES_50MHZ;
704 else
705 data = REF_FREF_SEL_SERDES_25MHZ;
706
707 mask = REF_FREF_SEL_MASK;
708 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
709
710 /*
711 * 10. Program COMPHY register PHY_GEN_MAX[1:0]
712 * This step is mentioned in the flow received from verification team.
713 * However the PHY_GEN_MAX value is only meaningful for other interfaces
714 * (not SERDES). For instance, it selects SATA speed 1.5/3/6 Gbps or
715 * PCIe speed 2.5/5 Gbps
716 */
717
718 /*
719 * 11. Program COMPHY register SEL_BITS to set correct parallel data
720 * bus width
721 */
722 data = DATA_WIDTH_10BIT;
723 mask = SEL_DATA_WIDTH_MASK;
724 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, data, mask);
725
726 /*
727 * 12. As long as DFE function needs to be enabled in any mode,
728 * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F
729 * for real chip during COMPHY power on.
730 * The value of the DFE_UPDATE_EN already is 0x3F, because it is the
731 * default value after reset of the PHY.
732 */
733
734 /*
735 * 13. Program COMPHY GEN registers.
736 * These registers should be programmed based on the lab testing result
737 * to achieve optimal performance. Please contact the CEA group to get
738 * the related GEN table during real chip bring-up. We only required to
739 * run though the entire registers programming flow defined by
740 * "comphy_gbe_phy_init" when the REF clock is 40 MHz. For REF clock
741 * 25 MHz the default values stored in PHY registers are OK.
742 */
743 dev_dbg(lane->dev, "Running C-DPI phy init %s mode\n",
744 lane->submode == PHY_INTERFACE_MODE_2500BASEX ? "2G5" : "1G");
745 if (lane->priv->xtal_is_40m)
746 comphy_gbe_phy_init(lane,
747 lane->submode != PHY_INTERFACE_MODE_2500BASEX);
748
749 /*
750 * 14. Check the PHY Polarity invert bit
751 */
752 data = 0x0;
753 if (lane->invert_tx)
754 data |= TXD_INVERT_BIT;
755 if (lane->invert_rx)
756 data |= RXD_INVERT_BIT;
757 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
758 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
759
760 /*
761 * 15. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 to
762 * start PHY power up sequence. All the PHY register programming should
763 * be done before PIN_PU_PLL=1. There should be no register programming
764 * for normal PHY operation from this point.
765 */
766 data = PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT;
767 mask = data;
768 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
769
770 /*
771 * 16. Wait for PHY power up sequence to finish by checking output ports
772 * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1.
773 */
774 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
775 PHY_PLL_READY_TX_BIT |
776 PHY_PLL_READY_RX_BIT,
777 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
778 if (ret) {
779 dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
780 lane->id);
781 return ret;
782 }
783
784 /*
785 * 17. Set COMPHY input port PIN_TX_IDLE=0
786 */
787 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, 0x0, PIN_TX_IDLE_BIT);
788
789 /*
790 * 18. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. To
791 * start RX initialization. PIN_RX_INIT_DONE will be cleared to 0 by the
792 * PHY After RX initialization is done, PIN_RX_INIT_DONE will be set to
793 * 1 by COMPHY Set PIN_RX_INIT=0 after PIN_RX_INIT_DONE= 1. Please
794 * refer to RX initialization part for details.
795 */
796 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1,
797 PHY_RX_INIT_BIT, PHY_RX_INIT_BIT);
798
799 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
800 PHY_PLL_READY_TX_BIT |
801 PHY_PLL_READY_RX_BIT,
802 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
803 if (ret) {
804 dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
805 lane->id);
806 return ret;
807 }
808
809 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
810 PHY_RX_INIT_DONE_BIT,
811 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
812 if (ret)
813 dev_err(lane->dev, "Failed to init RX of SERDES PHY %d\n",
814 lane->id);
815
816 return ret;
817}
818
819static int
820mvebu_a3700_comphy_usb3_power_on(struct mvebu_a3700_comphy_lane *lane)
821{
822 u32 mask, data, cfg, ref_clk;
823 int ret;
824
825 /* Set phy seclector */
826 ret = mvebu_a3700_comphy_set_phy_selector(lane);
827 if (ret)
828 return ret;
829
830 /*
831 * 0. Set PHY OTG Control(0x5d034), bit 4, Power up OTG module The
832 * register belong to UTMI module, so it is set in UTMI phy driver.
833 */
834
835 /*
836 * 1. Set PRD_TXDEEMPH (3.5db de-emph)
837 */
838 data = PRD_TXDEEMPH0_MASK;
839 mask = PRD_TXDEEMPH0_MASK | PRD_TXMARGIN_MASK | PRD_TXSWING_MASK |
840 CFG_TX_ALIGN_POS_MASK;
841 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG0, data, mask);
842
843 /*
844 * 2. Set BIT0: enable transmitter in high impedance mode
845 * Set BIT[3:4]: delay 2 clock cycles for HiZ off latency
846 * Set BIT6: Tx detect Rx at HiZ mode
847 * Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db
848 * together with bit 0 of COMPHY_PIPE_LANE_CFG0 register
849 */
850 data = TX_DET_RX_MODE | GEN2_TX_DATA_DLY_DEFT | TX_ELEC_IDLE_MODE_EN;
851 mask = PRD_TXDEEMPH1_MASK | TX_DET_RX_MODE | GEN2_TX_DATA_DLY_MASK |
852 TX_ELEC_IDLE_MODE_EN;
853 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1, data, mask);
854
855 /*
856 * 3. Set Spread Spectrum Clock Enabled
857 */
858 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG4,
859 SPREAD_SPECTRUM_CLK_EN, SPREAD_SPECTRUM_CLK_EN);
860
861 /*
862 * 4. Set Override Margining Controls From the MAC:
863 * Use margining signals from lane configuration
864 */
865 comphy_lane_reg_set(lane, COMPHY_PIPE_TEST_MODE_CTRL,
866 MODE_MARGIN_OVERRIDE, 0xFFFF);
867
868 /*
869 * 5. Set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles
870 * set Mode Clock Source = PCLK is generated from REFCLK
871 */
872 data = 0x0;
873 mask = MODE_CLK_SRC | BUNDLE_PERIOD_SEL | BUNDLE_PERIOD_SCALE_MASK |
874 BUNDLE_SAMPLE_CTRL | PLL_READY_DLY_MASK;
875 comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO, data, mask);
876
877 /*
878 * 6. Set G2 Spread Spectrum Clock Amplitude at 4K
879 */
880 comphy_lane_reg_set(lane, COMPHY_GEN2_SET2,
881 GS2_TX_SSC_AMP_4128, GS2_TX_SSC_AMP_MASK);
882
883 /*
884 * 7. Unset G3 Spread Spectrum Clock Amplitude
885 * set G3 TX and RX Register Master Current Select
886 */
887 data = GS2_VREG_RXTX_MAS_ISET_60U;
888 mask = GS2_TX_SSC_AMP_MASK | GS2_VREG_RXTX_MAS_ISET_MASK |
889 GS2_RSVD_6_0_MASK;
890 comphy_lane_reg_set(lane, COMPHY_GEN3_SET2, data, mask);
891
892 /*
893 * 8. Check crystal jumper setting and program the Power and PLL Control
894 * accordingly Change RX wait
895 */
896 if (lane->priv->xtal_is_40m) {
897 ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
898 cfg = CFG_PM_RXDLOZ_WAIT_12_UNIT;
899 } else {
900 ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
901 cfg = CFG_PM_RXDLOZ_WAIT_7_UNIT;
902 }
903
904 data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
905 PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_USB3 | ref_clk;
906 mask = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
907 PU_TX_INTP_BIT | PU_DFE_BIT | PLL_LOCK_BIT | COMPHY_MODE_MASK |
908 REF_FREF_SEL_MASK;
909 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
910
911 data = CFG_PM_RXDEN_WAIT_1_UNIT | cfg;
912 mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
913 CFG_PM_RXDLOZ_WAIT_MASK;
914 comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
915
916 /*
917 * 9. Enable idle sync
918 */
919 comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
920 IDLE_SYNC_EN, IDLE_SYNC_EN);
921
922 /*
923 * 10. Enable the output of 500M clock
924 */
925 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, CLK500M_EN, CLK500M_EN);
926
927 /*
928 * 11. Set 20-bit data width
929 */
930 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
931 DATA_WIDTH_20BIT, 0xFFFF);
932
933 /*
934 * 12. Override Speed_PLL value and use MAC PLL
935 */
936 data = SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT;
937 mask = 0xFFFF;
938 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, data, mask);
939
940 /*
941 * 13. Check the Polarity invert bit
942 */
943 data = 0x0;
944 if (lane->invert_tx)
945 data |= TXD_INVERT_BIT;
946 if (lane->invert_rx)
947 data |= RXD_INVERT_BIT;
948 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
949 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
950
951 /*
952 * 14. Set max speed generation to USB3.0 5Gbps
953 */
954 comphy_lane_reg_set(lane, COMPHY_SYNC_MASK_GEN,
955 PHY_GEN_MAX_USB3_5G, PHY_GEN_MAX_MASK);
956
957 /*
958 * 15. Set capacitor value for FFE gain peaking to 0xF
959 */
960 comphy_lane_reg_set(lane, COMPHY_GEN2_SET3,
961 GS3_FFE_CAP_SEL_VALUE, GS3_FFE_CAP_SEL_MASK);
962
963 /*
964 * 16. Release SW reset
965 */
966 data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32 | MODE_REFDIV_BY_4;
967 mask = 0xFFFF;
968 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
969
970 /* Wait for > 55 us to allow PCLK be enabled */
971 udelay(PLL_SET_DELAY_US);
972
973 ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
974 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
975 if (ret)
976 dev_err(lane->dev, "Failed to lock USB3 PLL\n");
977
978 return ret;
979}
980
981static int
982mvebu_a3700_comphy_pcie_power_on(struct mvebu_a3700_comphy_lane *lane)
983{
984 u32 mask, data, ref_clk;
985 int ret;
986
987 /* Configure phy selector for PCIe */
988 ret = mvebu_a3700_comphy_set_phy_selector(lane);
989 if (ret)
990 return ret;
991
992 /* 1. Enable max PLL. */
993 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1,
994 USE_MAX_PLL_RATE_EN, USE_MAX_PLL_RATE_EN);
995
996 /* 2. Select 20 bit SERDES interface. */
997 comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO,
998 CFG_SEL_20B, CFG_SEL_20B);
999
1000 /* 3. Force to use reg setting for PCIe mode */
1001 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL1,
1002 SEL_BITS_PCIE_FORCE, SEL_BITS_PCIE_FORCE);
1003
1004 /* 4. Change RX wait */
1005 data = CFG_PM_RXDEN_WAIT_1_UNIT | CFG_PM_RXDLOZ_WAIT_12_UNIT;
1006 mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
1007 CFG_PM_RXDLOZ_WAIT_MASK;
1008 comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
1009
1010 /* 5. Enable idle sync */
1011 comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
1012 IDLE_SYNC_EN, IDLE_SYNC_EN);
1013
1014 /* 6. Enable the output of 100M/125M/500M clock */
1015 data = CLK500M_EN | TXDCLK_2X_SEL | CLK100M_125M_EN;
1016 mask = data;
1017 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
1018
1019 /*
1020 * 7. Enable TX, PCIE global register, 0xd0074814, it is done in
1021 * PCI-E driver
1022 */
1023
1024 /*
1025 * 8. Check crystal jumper setting and program the Power and PLL
1026 * Control accordingly
1027 */
1028
1029 if (lane->priv->xtal_is_40m)
1030 ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
1031 else
1032 ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
1033
1034 data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
1035 PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_PCIE | ref_clk;
1036 mask = 0xFFFF;
1037 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
1038
1039 /* 9. Override Speed_PLL value and use MAC PLL */
1040 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
1041 SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT,
1042 0xFFFF);
1043
1044 /* 10. Check the Polarity invert bit */
1045 data = 0x0;
1046 if (lane->invert_tx)
1047 data |= TXD_INVERT_BIT;
1048 if (lane->invert_rx)
1049 data |= RXD_INVERT_BIT;
1050 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
1051 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
1052
1053 /* 11. Release SW reset */
1054 data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32;
1055 mask = data | PIPE_SOFT_RESET | MODE_REFDIV_MASK;
1056 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
1057
1058 /* Wait for > 55 us to allow PCLK be enabled */
1059 udelay(PLL_SET_DELAY_US);
1060
1061 ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
1062 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
1063 if (ret)
1064 dev_err(lane->dev, "Failed to lock PCIE PLL\n");
1065
1066 return ret;
1067}
1068
1069static void
1070mvebu_a3700_comphy_sata_power_off(struct mvebu_a3700_comphy_lane *lane)
1071{
1072 /* Set phy isolation mode */
1073 comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
1074 PHY_ISOLATE_MODE, PHY_ISOLATE_MODE);
1075
1076 /* Power off PLL, Tx, Rx */
1077 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1078 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1079}
1080
1081static void
1082mvebu_a3700_comphy_ethernet_power_off(struct mvebu_a3700_comphy_lane *lane)
1083{
1084 u32 mask, data;
1085
1086 data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT | PIN_PU_IVREF_BIT |
1087 PHY_RX_INIT_BIT;
1088 mask = data;
1089 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
1090}
1091
1092static void
1093mvebu_a3700_comphy_pcie_power_off(struct mvebu_a3700_comphy_lane *lane)
1094{
1095 /* Power off PLL, Tx, Rx */
1096 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1097 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1098}
1099
1100static int mvebu_a3700_comphy_reset(struct phy *phy)
1101{
1102 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1103 u16 mask, data;
1104
1105 dev_dbg(lane->dev, "resetting lane %d\n", lane->id);
1106
1107 /* COMPHY reset for internal logic */
1108 comphy_lane_reg_set(lane, COMPHY_SFT_RESET,
1109 SFT_RST_NO_REG, SFT_RST_NO_REG);
1110
1111 /* COMPHY register reset (cleared automatically) */
1112 comphy_lane_reg_set(lane, COMPHY_SFT_RESET, SFT_RST, SFT_RST);
1113
1114 /* PIPE soft and register reset */
1115 data = PIPE_SOFT_RESET | PIPE_REG_RESET;
1116 mask = data;
1117 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
1118
1119 /* Release PIPE register reset */
1120 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL,
1121 0x0, PIPE_REG_RESET);
1122
1123 /* Reset SB configuration register (only for lanes 0 and 1) */
1124 if (lane->id == 0 || lane->id == 1) {
1125 u32 mask, data;
1126
1127 data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT |
1128 PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT;
1129 mask = data | PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT;
1130 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
1131 }
1132
1133 return 0;
1134}
1135
1136static bool mvebu_a3700_comphy_check_mode(int lane,
1137 enum phy_mode mode,
1138 int submode)
1139{
1140 int i, n = ARRAY_SIZE(mvebu_a3700_comphy_modes);
1141
1142 /* Unused PHY mux value is 0x0 */
1143 if (mode == PHY_MODE_INVALID)
1144 return false;
1145
1146 for (i = 0; i < n; i++) {
1147 if (mvebu_a3700_comphy_modes[i].lane == lane &&
1148 mvebu_a3700_comphy_modes[i].mode == mode &&
1149 mvebu_a3700_comphy_modes[i].submode == submode)
1150 break;
1151 }
1152
1153 if (i == n)
1154 return false;
1155
1156 return true;
1157}
1158
1159static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode,
1160 int submode)
1161{
1162 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1163
1164 if (!mvebu_a3700_comphy_check_mode(lane->id, mode, submode)) {
1165 dev_err(lane->dev, "invalid COMPHY mode\n");
1166 return -EINVAL;
1167 }
1168
1169 /* Mode cannot be changed while the PHY is powered on */
1170 if (phy->power_count &&
1171 (lane->mode != mode || lane->submode != submode))
1172 return -EBUSY;
1173
1174 /* If changing mode, ensure reset is called */
1175 if (lane->mode != PHY_MODE_INVALID && lane->mode != mode)
1176 lane->needs_reset = true;
1177
1178 /* Just remember the mode, ->power_on() will do the real setup */
1179 lane->mode = mode;
1180 lane->submode = submode;
1181
1182 return 0;
1183}
1184
1185static int mvebu_a3700_comphy_power_on(struct phy *phy)
1186{
1187 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1188 int ret;
1189
1190 if (!mvebu_a3700_comphy_check_mode(lane->id, lane->mode,
1191 lane->submode)) {
1192 dev_err(lane->dev, "invalid COMPHY mode\n");
1193 return -EINVAL;
1194 }
1195
1196 if (lane->needs_reset) {
1197 ret = mvebu_a3700_comphy_reset(phy);
1198 if (ret)
1199 return ret;
1200
1201 lane->needs_reset = false;
1202 }
1203
1204 switch (lane->mode) {
1205 case PHY_MODE_USB_HOST_SS:
1206 dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id);
1207 return mvebu_a3700_comphy_usb3_power_on(lane);
1208 case PHY_MODE_SATA:
1209 dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id);
1210 return mvebu_a3700_comphy_sata_power_on(lane);
1211 case PHY_MODE_ETHERNET:
1212 dev_dbg(lane->dev, "set lane %d to Ethernet mode\n", lane->id);
1213 return mvebu_a3700_comphy_ethernet_power_on(lane);
1214 case PHY_MODE_PCIE:
1215 dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id);
1216 return mvebu_a3700_comphy_pcie_power_on(lane);
1217 default:
1218 dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode);
1219 return -EOPNOTSUPP;
1220 }
1221}
1222
1223static int mvebu_a3700_comphy_power_off(struct phy *phy)
1224{
1225 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1226
1227 switch (lane->mode) {
1228 case PHY_MODE_USB_HOST_SS:
1229 /*
1230 * The USB3 MAC sets the USB3 PHY to low state, so we do not
1231 * need to power off USB3 PHY again.
1232 */
1233 break;
1234
1235 case PHY_MODE_SATA:
1236 mvebu_a3700_comphy_sata_power_off(lane);
1237 break;
1238
1239 case PHY_MODE_ETHERNET:
1240 mvebu_a3700_comphy_ethernet_power_off(lane);
1241 break;
1242
1243 case PHY_MODE_PCIE:
1244 mvebu_a3700_comphy_pcie_power_off(lane);
1245 break;
1246
1247 default:
1248 dev_err(lane->dev, "invalid COMPHY mode\n");
1249 return -EINVAL;
1250 }
1251
1252 return 0;
1253}
1254
1255static const struct phy_ops mvebu_a3700_comphy_ops = {
1256 .power_on = mvebu_a3700_comphy_power_on,
1257 .power_off = mvebu_a3700_comphy_power_off,
1258 .reset = mvebu_a3700_comphy_reset,
1259 .set_mode = mvebu_a3700_comphy_set_mode,
1260 .owner = THIS_MODULE,
1261};
1262
1263static struct phy *mvebu_a3700_comphy_xlate(struct device *dev,
1264 struct of_phandle_args *args)
1265{
1266 struct mvebu_a3700_comphy_lane *lane;
1267 unsigned int port;
1268 struct phy *phy;
1269
1270 phy = of_phy_simple_xlate(dev, args);
1271 if (IS_ERR(phy))
1272 return phy;
1273
1274 lane = phy_get_drvdata(phy);
1275
1276 port = args->args[0];
1277 if (port != 0 && (port != 1 || lane->id != 0)) {
1278 dev_err(lane->dev, "invalid port number %u\n", port);
1279 return ERR_PTR(-EINVAL);
1280 }
1281
1282 lane->invert_tx = args->args[1] & BIT(0);
1283 lane->invert_rx = args->args[1] & BIT(1);
1284
1285 return phy;
1286}
1287
1288static int mvebu_a3700_comphy_probe(struct platform_device *pdev)
1289{
1290 struct mvebu_a3700_comphy_priv *priv;
1291 struct phy_provider *provider;
1292 struct device_node *child;
1293 struct resource *res;
1294 struct clk *clk;
1295 int ret;
1296
1297 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
1298 if (!priv)
1299 return -ENOMEM;
1300
1301 spin_lock_init(&priv->lock);
1302
1303 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "comphy");
1304 priv->comphy_regs = devm_ioremap_resource(&pdev->dev, res);
1305 if (IS_ERR(priv->comphy_regs))
1306 return PTR_ERR(priv->comphy_regs);
1307
1308 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1309 "lane1_pcie_gbe");
1310 priv->lane1_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1311 if (IS_ERR(priv->lane1_phy_regs))
1312 return PTR_ERR(priv->lane1_phy_regs);
1313
1314 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1315 "lane0_usb3_gbe");
1316 priv->lane0_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1317 if (IS_ERR(priv->lane0_phy_regs))
1318 return PTR_ERR(priv->lane0_phy_regs);
1319
1320 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1321 "lane2_sata_usb3");
1322 priv->lane2_phy_indirect = devm_ioremap_resource(&pdev->dev, res);
1323 if (IS_ERR(priv->lane2_phy_indirect))
1324 return PTR_ERR(priv->lane2_phy_indirect);
1325
1326 /*
1327 * Driver needs to know if reference xtal clock is 40MHz or 25MHz.
1328 * Old DT bindings do not have xtal clk present. So do not fail here
1329 * and expects that default 25MHz reference clock is used.
1330 */
1331 clk = clk_get(&pdev->dev, "xtal");
1332 if (IS_ERR(clk)) {
1333 if (PTR_ERR(clk) == -EPROBE_DEFER)
1334 return -EPROBE_DEFER;
1335 dev_warn(&pdev->dev, "missing 'xtal' clk (%ld)\n",
1336 PTR_ERR(clk));
1337 } else {
1338 ret = clk_prepare_enable(clk);
1339 if (ret) {
1340 dev_warn(&pdev->dev, "enabling xtal clk failed (%d)\n",
1341 ret);
1342 } else {
1343 if (clk_get_rate(clk) == 40000000)
1344 priv->xtal_is_40m = true;
1345 clk_disable_unprepare(clk);
1346 }
1347 clk_put(clk);
1348 }
1349
1350 dev_set_drvdata(&pdev->dev, priv);
1351
1352 for_each_available_child_of_node(pdev->dev.of_node, child) {
1353 struct mvebu_a3700_comphy_lane *lane;
1354 struct phy *phy;
1355 int ret;
1356 u32 lane_id;
1357
1358 ret = of_property_read_u32(child, "reg", &lane_id);
1359 if (ret < 0) {
1360 dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
1361 ret);
1362 continue;
1363 }
1364
1365 if (lane_id >= 3) {
1366 dev_err(&pdev->dev, "invalid 'reg' property\n");
1367 continue;
1368 }
1369
1370 lane = devm_kzalloc(&pdev->dev, sizeof(*lane), GFP_KERNEL);
1371 if (!lane) {
1372 of_node_put(child);
1373 return -ENOMEM;
1374 }
1375
1376 phy = devm_phy_create(&pdev->dev, child,
1377 &mvebu_a3700_comphy_ops);
1378 if (IS_ERR(phy)) {
1379 of_node_put(child);
1380 return PTR_ERR(phy);
1381 }
1382
1383 lane->priv = priv;
1384 lane->dev = &pdev->dev;
1385 lane->mode = PHY_MODE_INVALID;
1386 lane->submode = PHY_INTERFACE_MODE_NA;
1387 lane->id = lane_id;
1388 lane->invert_tx = false;
1389 lane->invert_rx = false;
1390 phy_set_drvdata(phy, lane);
1391
1392 /*
1393 * To avoid relying on the bootloader/firmware configuration,
1394 * power off all comphys.
1395 */
1396 mvebu_a3700_comphy_reset(phy);
1397 lane->needs_reset = false;
1398 }
1399
1400 provider = devm_of_phy_provider_register(&pdev->dev,
1401 mvebu_a3700_comphy_xlate);
1402
1403 return PTR_ERR_OR_ZERO(provider);
1404}
1405
1406static const struct of_device_id mvebu_a3700_comphy_of_match_table[] = {
1407 { .compatible = "marvell,comphy-a3700" },
1408 { },
1409};
1410MODULE_DEVICE_TABLE(of, mvebu_a3700_comphy_of_match_table);
1411
1412static struct platform_driver mvebu_a3700_comphy_driver = {
1413 .probe = mvebu_a3700_comphy_probe,
1414 .driver = {
1415 .name = "mvebu-a3700-comphy",
1416 .of_match_table = mvebu_a3700_comphy_of_match_table,
1417 },
1418};
1419module_platform_driver(mvebu_a3700_comphy_driver);
1420
1421MODULE_AUTHOR("Miquèl Raynal <miquel.raynal@bootlin.com>");
1422MODULE_AUTHOR("Pali Rohár <pali@kernel.org>");
1423MODULE_AUTHOR("Marek Behún <kabel@kernel.org>");
1424MODULE_DESCRIPTION("Common PHY driver for A3700");
1425MODULE_LICENSE("GPL v2");