tjh.dev
Linux kernel mirror (for testing)
git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
kernel
os
linux
1/*======================================================================
2
3 A driver for PCMCIA serial devices
4
5 serial_cs.c 1.134 2002/05/04 05:48:53
6
7 The contents of this file are subject to the Mozilla Public
8 License Version 1.1 (the "License"); you may not use this file
9 except in compliance with the License. You may obtain a copy of
10 the License at http://www.mozilla.org/MPL/
11
12 Software distributed under the License is distributed on an "AS
13 IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
14 implied. See the License for the specific language governing
15 rights and limitations under the License.
16
17 The initial developer of the original code is David A. Hinds
18 <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
19 are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
20
21 Alternatively, the contents of this file may be used under the
22 terms of the GNU General Public License version 2 (the "GPL"), in which
23 case the provisions of the GPL are applicable instead of the
24 above. If you wish to allow the use of your version of this file
25 only under the terms of the GPL and not to allow others to use
26 your version of this file under the MPL, indicate your decision
27 by deleting the provisions above and replace them with the notice
28 and other provisions required by the GPL. If you do not delete
29 the provisions above, a recipient may use your version of this
30 file under either the MPL or the GPL.
31
32======================================================================*/
33
34#include <linux/module.h>
35#include <linux/moduleparam.h>
36#include <linux/kernel.h>
37#include <linux/init.h>
38#include <linux/ptrace.h>
39#include <linux/slab.h>
40#include <linux/string.h>
41#include <linux/timer.h>
42#include <linux/serial_core.h>
43#include <linux/delay.h>
44#include <linux/major.h>
45#include <asm/io.h>
46#include <asm/system.h>
47
48#include <pcmcia/cs_types.h>
49#include <pcmcia/cs.h>
50#include <pcmcia/cistpl.h>
51#include <pcmcia/ciscode.h>
52#include <pcmcia/ds.h>
53#include <pcmcia/cisreg.h>
54
55#include "8250.h"
56
57
58/*====================================================================*/
59
60/* Parameters that can be set with 'insmod' */
61
62/* Enable the speaker? */
63static int do_sound = 1;
64/* Skip strict UART tests? */
65static int buggy_uart;
66
67module_param(do_sound, int, 0444);
68module_param(buggy_uart, int, 0444);
69
70/*====================================================================*/
71
72/* Table of multi-port card ID's */
73
74struct serial_quirk {
75 unsigned int manfid;
76 unsigned int prodid;
77 int multi; /* 1 = multifunction, > 1 = # ports */
78 void (*config)(struct pcmcia_device *);
79 void (*setup)(struct pcmcia_device *, struct uart_port *);
80 void (*wakeup)(struct pcmcia_device *);
81 int (*post)(struct pcmcia_device *);
82};
83
84struct serial_info {
85 struct pcmcia_device *p_dev;
86 int ndev;
87 int multi;
88 int slave;
89 int manfid;
90 int prodid;
91 int c950ctrl;
92 dev_node_t node[4];
93 int line[4];
94 const struct serial_quirk *quirk;
95};
96
97struct serial_cfg_mem {
98 tuple_t tuple;
99 cisparse_t parse;
100 u_char buf[256];
101};
102
103/*
104 * vers_1 5.0, "Brain Boxes", "2-Port RS232 card", "r6"
105 * manfid 0x0160, 0x0104
106 * This card appears to have a 14.7456MHz clock.
107 */
108static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port)
109{
110 port->uartclk = 14745600;
111}
112
113static int quirk_post_ibm(struct pcmcia_device *link)
114{
115 conf_reg_t reg = { 0, CS_READ, 0x800, 0 };
116 int ret;
117
118 ret = pcmcia_access_configuration_register(link, ®);
119 if (ret)
120 goto failed;
121
122 reg.Action = CS_WRITE;
123 reg.Value = reg.Value | 1;
124 ret = pcmcia_access_configuration_register(link, ®);
125 if (ret)
126 goto failed;
127 return 0;
128
129 failed:
130 return -ENODEV;
131}
132
133/*
134 * Nokia cards are not really multiport cards. Shouldn't this
135 * be handled by setting the quirk entry .multi = 0 | 1 ?
136 */
137static void quirk_config_nokia(struct pcmcia_device *link)
138{
139 struct serial_info *info = link->priv;
140
141 if (info->multi > 1)
142 info->multi = 1;
143}
144
145static void quirk_wakeup_oxsemi(struct pcmcia_device *link)
146{
147 struct serial_info *info = link->priv;
148
149 if (info->c950ctrl)
150 outb(12, info->c950ctrl + 1);
151}
152
153/* request_region? oxsemi branch does no request_region too... */
154/*
155 * This sequence is needed to properly initialize MC45 attached to OXCF950.
156 * I tried decreasing these msleep()s, but it worked properly (survived
157 * 1000 stop/start operations) with these timeouts (or bigger).
158 */
159static void quirk_wakeup_possio_gcc(struct pcmcia_device *link)
160{
161 struct serial_info *info = link->priv;
162 unsigned int ctrl = info->c950ctrl;
163
164 outb(0xA, ctrl + 1);
165 msleep(100);
166 outb(0xE, ctrl + 1);
167 msleep(300);
168 outb(0xC, ctrl + 1);
169 msleep(100);
170 outb(0xE, ctrl + 1);
171 msleep(200);
172 outb(0xF, ctrl + 1);
173 msleep(100);
174 outb(0xE, ctrl + 1);
175 msleep(100);
176 outb(0xC, ctrl + 1);
177}
178
179/*
180 * Socket Dual IO: this enables irq's for second port
181 */
182static void quirk_config_socket(struct pcmcia_device *link)
183{
184 struct serial_info *info = link->priv;
185
186 if (info->multi) {
187 link->conf.Present |= PRESENT_EXT_STATUS;
188 link->conf.ExtStatus = ESR_REQ_ATTN_ENA;
189 }
190}
191
192static const struct serial_quirk quirks[] = {
193 {
194 .manfid = 0x0160,
195 .prodid = 0x0104,
196 .multi = -1,
197 .setup = quirk_setup_brainboxes_0104,
198 }, {
199 .manfid = MANFID_IBM,
200 .prodid = ~0,
201 .multi = -1,
202 .post = quirk_post_ibm,
203 }, {
204 .manfid = MANFID_INTEL,
205 .prodid = PRODID_INTEL_DUAL_RS232,
206 .multi = 2,
207 }, {
208 .manfid = MANFID_NATINST,
209 .prodid = PRODID_NATINST_QUAD_RS232,
210 .multi = 4,
211 }, {
212 .manfid = MANFID_NOKIA,
213 .prodid = ~0,
214 .multi = -1,
215 .config = quirk_config_nokia,
216 }, {
217 .manfid = MANFID_OMEGA,
218 .prodid = PRODID_OMEGA_QSP_100,
219 .multi = 4,
220 }, {
221 .manfid = MANFID_OXSEMI,
222 .prodid = ~0,
223 .multi = -1,
224 .wakeup = quirk_wakeup_oxsemi,
225 }, {
226 .manfid = MANFID_POSSIO,
227 .prodid = PRODID_POSSIO_GCC,
228 .multi = -1,
229 .wakeup = quirk_wakeup_possio_gcc,
230 }, {
231 .manfid = MANFID_QUATECH,
232 .prodid = PRODID_QUATECH_DUAL_RS232,
233 .multi = 2,
234 }, {
235 .manfid = MANFID_QUATECH,
236 .prodid = PRODID_QUATECH_DUAL_RS232_D1,
237 .multi = 2,
238 }, {
239 .manfid = MANFID_QUATECH,
240 .prodid = PRODID_QUATECH_DUAL_RS232_G,
241 .multi = 2,
242 }, {
243 .manfid = MANFID_QUATECH,
244 .prodid = PRODID_QUATECH_QUAD_RS232,
245 .multi = 4,
246 }, {
247 .manfid = MANFID_SOCKET,
248 .prodid = PRODID_SOCKET_DUAL_RS232,
249 .multi = 2,
250 .config = quirk_config_socket,
251 }, {
252 .manfid = MANFID_SOCKET,
253 .prodid = ~0,
254 .multi = -1,
255 .config = quirk_config_socket,
256 }
257};
258
259
260static int serial_config(struct pcmcia_device * link);
261
262
263/*======================================================================
264
265 After a card is removed, serial_remove() will unregister
266 the serial device(s), and release the PCMCIA configuration.
267
268======================================================================*/
269
270static void serial_remove(struct pcmcia_device *link)
271{
272 struct serial_info *info = link->priv;
273 int i;
274
275 dev_dbg(&link->dev, "serial_release\n");
276
277 /*
278 * Recheck to see if the device is still configured.
279 */
280 for (i = 0; i < info->ndev; i++)
281 serial8250_unregister_port(info->line[i]);
282
283 info->p_dev->dev_node = NULL;
284
285 if (!info->slave)
286 pcmcia_disable_device(link);
287}
288
289static int serial_suspend(struct pcmcia_device *link)
290{
291 struct serial_info *info = link->priv;
292 int i;
293
294 for (i = 0; i < info->ndev; i++)
295 serial8250_suspend_port(info->line[i]);
296
297 return 0;
298}
299
300static int serial_resume(struct pcmcia_device *link)
301{
302 struct serial_info *info = link->priv;
303 int i;
304
305 for (i = 0; i < info->ndev; i++)
306 serial8250_resume_port(info->line[i]);
307
308 if (info->quirk && info->quirk->wakeup)
309 info->quirk->wakeup(link);
310
311 return 0;
312}
313
314/*======================================================================
315
316 serial_attach() creates an "instance" of the driver, allocating
317 local data structures for one device. The device is registered
318 with Card Services.
319
320======================================================================*/
321
322static int serial_probe(struct pcmcia_device *link)
323{
324 struct serial_info *info;
325
326 dev_dbg(&link->dev, "serial_attach()\n");
327
328 /* Create new serial device */
329 info = kzalloc(sizeof (*info), GFP_KERNEL);
330 if (!info)
331 return -ENOMEM;
332 info->p_dev = link;
333 link->priv = info;
334
335 link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
336 link->io.NumPorts1 = 8;
337 link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING;
338 link->conf.Attributes = CONF_ENABLE_IRQ;
339 if (do_sound) {
340 link->conf.Attributes |= CONF_ENABLE_SPKR;
341 link->conf.Status = CCSR_AUDIO_ENA;
342 }
343 link->conf.IntType = INT_MEMORY_AND_IO;
344
345 return serial_config(link);
346}
347
348/*======================================================================
349
350 This deletes a driver "instance". The device is de-registered
351 with Card Services. If it has been released, all local data
352 structures are freed. Otherwise, the structures will be freed
353 when the device is released.
354
355======================================================================*/
356
357static void serial_detach(struct pcmcia_device *link)
358{
359 struct serial_info *info = link->priv;
360
361 dev_dbg(&link->dev, "serial_detach\n");
362
363 /*
364 * Ensure any outstanding scheduled tasks are completed.
365 */
366 flush_scheduled_work();
367
368 /*
369 * Ensure that the ports have been released.
370 */
371 serial_remove(link);
372
373 /* free bits */
374 kfree(info);
375}
376
377/*====================================================================*/
378
379static int setup_serial(struct pcmcia_device *handle, struct serial_info * info,
380 unsigned int iobase, int irq)
381{
382 struct uart_port port;
383 int line;
384
385 memset(&port, 0, sizeof (struct uart_port));
386 port.iobase = iobase;
387 port.irq = irq;
388 port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
389 port.uartclk = 1843200;
390 port.dev = &handle->dev;
391 if (buggy_uart)
392 port.flags |= UPF_BUGGY_UART;
393
394 if (info->quirk && info->quirk->setup)
395 info->quirk->setup(handle, &port);
396
397 line = serial8250_register_port(&port);
398 if (line < 0) {
399 printk(KERN_NOTICE "serial_cs: serial8250_register_port() at "
400 "0x%04lx, irq %d failed\n", (u_long)iobase, irq);
401 return -EINVAL;
402 }
403
404 info->line[info->ndev] = line;
405 sprintf(info->node[info->ndev].dev_name, "ttyS%d", line);
406 info->node[info->ndev].major = TTY_MAJOR;
407 info->node[info->ndev].minor = 0x40 + line;
408 if (info->ndev > 0)
409 info->node[info->ndev - 1].next = &info->node[info->ndev];
410 info->ndev++;
411
412 return 0;
413}
414
415/*====================================================================*/
416
417static int simple_config_check(struct pcmcia_device *p_dev,
418 cistpl_cftable_entry_t *cf,
419 cistpl_cftable_entry_t *dflt,
420 unsigned int vcc,
421 void *priv_data)
422{
423 static const int size_table[2] = { 8, 16 };
424 int *try = priv_data;
425
426 if (cf->vpp1.present & (1 << CISTPL_POWER_VNOM))
427 p_dev->conf.Vpp =
428 cf->vpp1.param[CISTPL_POWER_VNOM] / 10000;
429
430 if ((cf->io.nwin > 0) && (cf->io.win[0].len == size_table[(*try >> 1)])
431 && (cf->io.win[0].base != 0)) {
432 p_dev->io.BasePort1 = cf->io.win[0].base;
433 p_dev->io.IOAddrLines = ((*try & 0x1) == 0) ?
434 16 : cf->io.flags & CISTPL_IO_LINES_MASK;
435 if (!pcmcia_request_io(p_dev, &p_dev->io))
436 return 0;
437 }
438 return -EINVAL;
439}
440
441static int simple_config_check_notpicky(struct pcmcia_device *p_dev,
442 cistpl_cftable_entry_t *cf,
443 cistpl_cftable_entry_t *dflt,
444 unsigned int vcc,
445 void *priv_data)
446{
447 static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
448 int j;
449
450 if ((cf->io.nwin > 0) && ((cf->io.flags & CISTPL_IO_LINES_MASK) <= 3)) {
451 for (j = 0; j < 5; j++) {
452 p_dev->io.BasePort1 = base[j];
453 p_dev->io.IOAddrLines = base[j] ? 16 : 3;
454 if (!pcmcia_request_io(p_dev, &p_dev->io))
455 return 0;
456 }
457 }
458 return -ENODEV;
459}
460
461static int simple_config(struct pcmcia_device *link)
462{
463 struct serial_info *info = link->priv;
464 int i = -ENODEV, try;
465
466 /* If the card is already configured, look up the port and irq */
467 if (link->function_config) {
468 unsigned int port = 0;
469 if ((link->io.BasePort2 != 0) &&
470 (link->io.NumPorts2 == 8)) {
471 port = link->io.BasePort2;
472 info->slave = 1;
473 } else if ((info->manfid == MANFID_OSITECH) &&
474 (link->io.NumPorts1 == 0x40)) {
475 port = link->io.BasePort1 + 0x28;
476 info->slave = 1;
477 }
478 if (info->slave) {
479 return setup_serial(link, info, port,
480 link->irq.AssignedIRQ);
481 }
482 }
483
484 /* First pass: look for a config entry that looks normal.
485 * Two tries: without IO aliases, then with aliases */
486 for (try = 0; try < 4; try++)
487 if (!pcmcia_loop_config(link, simple_config_check, &try))
488 goto found_port;
489
490 /* Second pass: try to find an entry that isn't picky about
491 its base address, then try to grab any standard serial port
492 address, and finally try to get any free port. */
493 if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL))
494 goto found_port;
495
496 printk(KERN_NOTICE
497 "serial_cs: no usable port range found, giving up\n");
498 return -1;
499
500found_port:
501 i = pcmcia_request_irq(link, &link->irq);
502 if (i != 0)
503 link->irq.AssignedIRQ = 0;
504
505 if (info->multi && (info->manfid == MANFID_3COM))
506 link->conf.ConfigIndex &= ~(0x08);
507
508 /*
509 * Apply any configuration quirks.
510 */
511 if (info->quirk && info->quirk->config)
512 info->quirk->config(link);
513
514 i = pcmcia_request_configuration(link, &link->conf);
515 if (i != 0)
516 return -1;
517 return setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ);
518}
519
520static int multi_config_check(struct pcmcia_device *p_dev,
521 cistpl_cftable_entry_t *cf,
522 cistpl_cftable_entry_t *dflt,
523 unsigned int vcc,
524 void *priv_data)
525{
526 int *base2 = priv_data;
527
528 /* The quad port cards have bad CIS's, so just look for a
529 window larger than 8 ports and assume it will be right */
530 if ((cf->io.nwin == 1) && (cf->io.win[0].len > 8)) {
531 p_dev->io.BasePort1 = cf->io.win[0].base;
532 p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
533 if (!pcmcia_request_io(p_dev, &p_dev->io)) {
534 *base2 = p_dev->io.BasePort1 + 8;
535 return 0;
536 }
537 }
538 return -ENODEV;
539}
540
541static int multi_config_check_notpicky(struct pcmcia_device *p_dev,
542 cistpl_cftable_entry_t *cf,
543 cistpl_cftable_entry_t *dflt,
544 unsigned int vcc,
545 void *priv_data)
546{
547 int *base2 = priv_data;
548
549 if (cf->io.nwin == 2) {
550 p_dev->io.BasePort1 = cf->io.win[0].base;
551 p_dev->io.BasePort2 = cf->io.win[1].base;
552 p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
553 if (!pcmcia_request_io(p_dev, &p_dev->io)) {
554 *base2 = p_dev->io.BasePort2;
555 return 0;
556 }
557 }
558 return -ENODEV;
559}
560
561static int multi_config(struct pcmcia_device *link)
562{
563 struct serial_info *info = link->priv;
564 int i, base2 = 0;
565
566 /* First, look for a generic full-sized window */
567 link->io.NumPorts1 = info->multi * 8;
568 if (pcmcia_loop_config(link, multi_config_check, &base2)) {
569 /* If that didn't work, look for two windows */
570 link->io.NumPorts1 = link->io.NumPorts2 = 8;
571 info->multi = 2;
572 if (pcmcia_loop_config(link, multi_config_check_notpicky,
573 &base2)) {
574 printk(KERN_NOTICE "serial_cs: no usable port range"
575 "found, giving up\n");
576 return -ENODEV;
577 }
578 }
579
580 i = pcmcia_request_irq(link, &link->irq);
581 if (i != 0) {
582 /* FIXME: comment does not fit, error handling does not fit */
583 printk(KERN_NOTICE
584 "serial_cs: no usable port range found, giving up\n");
585 link->irq.AssignedIRQ = 0;
586 }
587
588 /*
589 * Apply any configuration quirks.
590 */
591 if (info->quirk && info->quirk->config)
592 info->quirk->config(link);
593
594 i = pcmcia_request_configuration(link, &link->conf);
595 if (i != 0)
596 return -ENODEV;
597
598 /* The Oxford Semiconductor OXCF950 cards are in fact single-port:
599 * 8 registers are for the UART, the others are extra registers.
600 * Siemen's MC45 PCMCIA (Possio's GCC) is OXCF950 based too.
601 */
602 if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO &&
603 info->prodid == PRODID_POSSIO_GCC)) {
604 int err;
605
606 if (link->conf.ConfigIndex == 1 ||
607 link->conf.ConfigIndex == 3) {
608 err = setup_serial(link, info, base2,
609 link->irq.AssignedIRQ);
610 base2 = link->io.BasePort1;
611 } else {
612 err = setup_serial(link, info, link->io.BasePort1,
613 link->irq.AssignedIRQ);
614 }
615 info->c950ctrl = base2;
616
617 /*
618 * FIXME: We really should wake up the port prior to
619 * handing it over to the serial layer.
620 */
621 if (info->quirk && info->quirk->wakeup)
622 info->quirk->wakeup(link);
623
624 return 0;
625 }
626
627 setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ);
628 for (i = 0; i < info->multi - 1; i++)
629 setup_serial(link, info, base2 + (8 * i),
630 link->irq.AssignedIRQ);
631 return 0;
632}
633
634static int serial_check_for_multi(struct pcmcia_device *p_dev,
635 cistpl_cftable_entry_t *cf,
636 cistpl_cftable_entry_t *dflt,
637 unsigned int vcc,
638 void *priv_data)
639{
640 struct serial_info *info = p_dev->priv;
641
642 if ((cf->io.nwin == 1) && (cf->io.win[0].len % 8 == 0))
643 info->multi = cf->io.win[0].len >> 3;
644
645 if ((cf->io.nwin == 2) && (cf->io.win[0].len == 8) &&
646 (cf->io.win[1].len == 8))
647 info->multi = 2;
648
649 return 0; /* break */
650}
651
652
653/*======================================================================
654
655 serial_config() is scheduled to run after a CARD_INSERTION event
656 is received, to configure the PCMCIA socket, and to make the
657 serial device available to the system.
658
659======================================================================*/
660
661static int serial_config(struct pcmcia_device * link)
662{
663 struct serial_info *info = link->priv;
664 int i;
665
666 dev_dbg(&link->dev, "serial_config\n");
667
668 /* Is this a compliant multifunction card? */
669 info->multi = (link->socket->functions > 1);
670
671 /* Is this a multiport card? */
672 info->manfid = link->manf_id;
673 info->prodid = link->card_id;
674
675 for (i = 0; i < ARRAY_SIZE(quirks); i++)
676 if ((quirks[i].manfid == ~0 ||
677 quirks[i].manfid == info->manfid) &&
678 (quirks[i].prodid == ~0 ||
679 quirks[i].prodid == info->prodid)) {
680 info->quirk = &quirks[i];
681 break;
682 }
683
684 /* Another check for dual-serial cards: look for either serial or
685 multifunction cards that ask for appropriate IO port ranges */
686 if ((info->multi == 0) &&
687 (link->has_func_id) &&
688 ((link->func_id == CISTPL_FUNCID_MULTI) ||
689 (link->func_id == CISTPL_FUNCID_SERIAL)))
690 pcmcia_loop_config(link, serial_check_for_multi, info);
691
692 /*
693 * Apply any multi-port quirk.
694 */
695 if (info->quirk && info->quirk->multi != -1)
696 info->multi = info->quirk->multi;
697
698 if (info->multi > 1)
699 i = multi_config(link);
700 else
701 i = simple_config(link);
702
703 if (i || info->ndev == 0)
704 goto failed;
705
706 /*
707 * Apply any post-init quirk. FIXME: This should really happen
708 * before we register the port, since it might already be in use.
709 */
710 if (info->quirk && info->quirk->post)
711 if (info->quirk->post(link))
712 goto failed;
713
714 link->dev_node = &info->node[0];
715 return 0;
716
717failed:
718 dev_warn(&link->dev, "serial_cs: failed to initialize\n");
719 serial_remove(link);
720 return -ENODEV;
721}
722
723static struct pcmcia_device_id serial_ids[] = {
724 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0057, 0x0021),
725 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0089, 0x110a),
726 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0104, 0x000a),
727 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0xea15),
728 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0109, 0x0501),
729 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0138, 0x110a),
730 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0140, 0x000a),
731 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0x3341),
732 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0xc0ab),
733 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x016c, 0x0081),
734 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x021b, 0x0101),
735 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x08a1, 0xc0ab),
736 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0d0a),
737 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0e0a),
738 PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3288", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x04cd2988, 0x46a52d63),
739 PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3336", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x0143b773, 0x46a52d63),
740 PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "EM1144T", "PCMCIA MODEM", 0xf510db04, 0x856d66c8, 0xbd6c43ef),
741 PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "XJEM1144/CCEM1144", "PCMCIA MODEM", 0xf510db04, 0x52d21e1e, 0xbd6c43ef),
742 PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM28", 0x2e3ee845, 0x0ea978ea),
743 PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM33", 0x2e3ee845, 0x80609023),
744 PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM56", 0x2e3ee845, 0xa650c32a),
745 PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "REM10", 0x2e3ee845, 0x76df1d29),
746 PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "XEM5600", 0x2e3ee845, 0xf1403719),
747 PCMCIA_PFC_DEVICE_PROD_ID12(1, "AnyCom", "Fast Ethernet + 56K COMBO", 0x578ba6e7, 0xb0ac62c4),
748 PCMCIA_PFC_DEVICE_PROD_ID12(1, "ATKK", "LM33-PCM-T", 0xba9eb7e2, 0x077c174e),
749 PCMCIA_PFC_DEVICE_PROD_ID12(1, "D-Link", "DME336T", 0x1a424a1c, 0xb23897ff),
750 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Gateway 2000", "XJEM3336", 0xdd9989be, 0x662c394c),
751 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae),
752 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033),
753 PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58),
754 PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e),
755 PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555),
756 PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001" ,0x18df0ba0 ,0x831b1064),
757 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9),
758 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed),
759 PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc),
760 PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f),
761 PCMCIA_PFC_DEVICE_PROD_ID12(1, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed),
762 PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf),
763 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0e01),
764 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05),
765 PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101),
766 PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070),
767 PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562),
768 PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0104, 0x0070),
769 PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x016c, 0x0020),
770 PCMCIA_MFC_DEVICE_PROD_ID123(1, "APEX DATA", "MULTICARD", "ETHERNET-MODEM", 0x11c2da09, 0x7289dc5d, 0xaad95e1f),
771 PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away 28.8 PC Card ", 0xb569a6e5, 0x5bd4ff2c),
772 PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away Credit Card Adapter", 0xb569a6e5, 0x4bdf15c3),
773 PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "w95 Home and Away Credit Card ", 0xb569a6e5, 0xae911c15),
774 PCMCIA_MFC_DEVICE_PROD_ID1(1, "Motorola MARQUIS", 0xf03e4e77),
775 PCMCIA_MFC_DEVICE_PROD_ID2(1, "FAX/Modem/Ethernet Combo Card ", 0x1ed59302),
776 PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0301),
777 PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x0276),
778 PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0039),
779 PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0006),
780 PCMCIA_DEVICE_MANF_CARD(0x0105, 0x410a),
781 PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d50),
782 PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d51),
783 PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d52),
784 PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d53),
785 PCMCIA_DEVICE_MANF_CARD(0x010b, 0xd180),
786 PCMCIA_DEVICE_MANF_CARD(0x0137, 0x000e),
787 PCMCIA_DEVICE_MANF_CARD(0x0137, 0x001b),
788 PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0025),
789 PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0045),
790 PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0052),
791 PCMCIA_DEVICE_PROD_ID134("ADV", "TECH", "COMpad-32/85", 0x67459937, 0x916d02ba, 0x8fbe92ae),
792 PCMCIA_DEVICE_PROD_ID124("GATEWAY2000", "CC3144", "PCMCIA MODEM", 0x506bccae, 0xcb3685f1, 0xbd6c43ef),
793 PCMCIA_DEVICE_PROD_ID14("MEGAHERTZ", "PCMCIA MODEM", 0xf510db04, 0xbd6c43ef),
794 PCMCIA_DEVICE_PROD_ID124("TOSHIBA", "T144PF", "PCMCIA MODEM", 0xb4585a1a, 0x7271409c, 0xbd6c43ef),
795 PCMCIA_DEVICE_PROD_ID123("FUJITSU", "FC14F ", "MBH10213", 0x6ee5a3d8, 0x30ead12b, 0xb00f05a0),
796 PCMCIA_DEVICE_PROD_ID123("Novatel Wireless", "Merlin UMTS Modem", "U630", 0x32607776, 0xd9e73b13, 0xe87332e),
797 PCMCIA_DEVICE_PROD_ID13("MEGAHERTZ", "V.34 PCMCIA MODEM", 0xf510db04, 0xbb2cce4a),
798 PCMCIA_DEVICE_PROD_ID12("Brain Boxes", "Bluetooth PC Card", 0xee138382, 0xd4ce9b02),
799 PCMCIA_DEVICE_PROD_ID12("CIRRUS LOGIC", "FAX MODEM", 0xe625f451, 0xcecd6dfa),
800 PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 28800 FAX/DATA MODEM", 0xa3a3062c, 0x8cbd7c76),
801 PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 33600 FAX/DATA MODEM", 0xa3a3062c, 0x5a00ce95),
802 PCMCIA_DEVICE_PROD_ID12("Computerboards, Inc.", "PCM-COM422", 0xd0b78f51, 0x7e2d49ed),
803 PCMCIA_DEVICE_PROD_ID12("Dr. Neuhaus", "FURY CARD 14K4", 0x76942813, 0x8b96ce65),
804 PCMCIA_DEVICE_PROD_ID12("Intelligent", "ANGIA FAX/MODEM", 0xb496e65e, 0xf31602a6),
805 PCMCIA_DEVICE_PROD_ID12("Intel", "MODEM 2400+", 0x816cc815, 0x412729fb),
806 PCMCIA_DEVICE_PROD_ID12("IOTech Inc ", "PCMCIA Dual RS-232 Serial Port Card", 0x3bd2d898, 0x92abc92f),
807 PCMCIA_DEVICE_PROD_ID12("MACRONIX", "FAX/MODEM", 0x668388b3, 0x3f9bdf2f),
808 PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT1432LT", 0x5f73be51, 0x0b3e2383),
809 PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e),
810 PCMCIA_DEVICE_PROD_ID12("OEM ", "C288MX ", 0xb572d360, 0xd2385b7a),
811 PCMCIA_DEVICE_PROD_ID12("PCMCIA ", "C336MX ", 0x99bcafe9, 0xaa25bcab),
812 PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f),
813 PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d),
814 PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"),
815 PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"),
816 PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"),
817 PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"),
818 PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"),
819 PCMCIA_MFC_DEVICE_CIS_PROD_ID12(1, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "cis/DP83903.cis"),
820 PCMCIA_MFC_DEVICE_CIS_PROD_ID4(1, "NSC MF LAN/Modem", 0x58fc6056, "cis/DP83903.cis"),
821 PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0556, "cis/3CCFEM556.cis"),
822 PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0175, 0x0000, "cis/DP83903.cis"),
823 PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0035, "cis/3CXEM556.cis"),
824 PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x003d, "cis/3CXEM556.cis"),
825 PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC850", 0xd85f6206, 0x42a2c018, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC850 3G Network Adapter R1 */
826 PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC860", 0xd85f6206, 0x698f93db, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC860 3G Network Adapter R1 */
827 PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC710/AC750", 0xd85f6206, 0x761b11e0, "cis/SW_7xx_SER.cis"), /* Sierra Wireless AC710/AC750 GPRS Network Adapter R1 */
828 PCMCIA_DEVICE_CIS_MANF_CARD(0x0192, 0xa555, "cis/SW_555_SER.cis"), /* Sierra Aircard 555 CDMA 1xrtt Modem -- pre update */
829 PCMCIA_DEVICE_CIS_MANF_CARD(0x013f, 0xa555, "cis/SW_555_SER.cis"), /* Sierra Aircard 555 CDMA 1xrtt Modem -- post update */
830 PCMCIA_DEVICE_CIS_PROD_ID12("MultiTech", "PCMCIA 56K DataFax", 0x842047ee, 0xc2efcf03, "cis/MT5634ZLX.cis"),
831 PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-2", 0x96913a85, 0x27ab5437, "cis/COMpad2.cis"),
832 PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"),
833 PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"),
834 PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"),
835 PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"),
836 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100 1.00.",0x19ca78af,0xf964f42b),
837 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100",0x19ca78af,0x71d98e83),
838 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232 1.00.",0x19ca78af,0x69fb7490),
839 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232",0x19ca78af,0xb6bc0235),
840 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232",0x63f2e0bd,0xb9e175d3),
841 PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232-5",0x63f2e0bd,0xfce33442),
842 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232",0x3beb8cf2,0x171e7190),
843 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232-5",0x3beb8cf2,0x20da4262),
844 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF428",0x3beb8cf2,0xea5dd57d),
845 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF500",0x3beb8cf2,0xd77255fa),
846 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: IC232",0x3beb8cf2,0x6a709903),
847 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: SL232",0x3beb8cf2,0x18430676),
848 PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: XL232",0x3beb8cf2,0x6f933767),
849 PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7),
850 PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41),
851 PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029),
852 PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4),
853 PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial+Parallel Port: SP230",0x3beb8cf2,0xdb9e58bc),
854 PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7),
855 PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41),
856 PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029),
857 PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4),
858 PCMCIA_MFC_DEVICE_PROD_ID12(2,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4),
859 PCMCIA_MFC_DEVICE_PROD_ID12(3,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4),
860 PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b),
861 /* too generic */
862 /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */
863 /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */
864 PCMCIA_DEVICE_FUNC_ID(2),
865 PCMCIA_DEVICE_NULL,
866};
867MODULE_DEVICE_TABLE(pcmcia, serial_ids);
868
869MODULE_FIRMWARE("cis/PCMLM28.cis");
870MODULE_FIRMWARE("cis/DP83903.cis");
871MODULE_FIRMWARE("cis/3CCFEM556.cis");
872MODULE_FIRMWARE("cis/3CXEM556.cis");
873MODULE_FIRMWARE("cis/SW_8xx_SER.cis");
874MODULE_FIRMWARE("cis/SW_7xx_SER.cis");
875MODULE_FIRMWARE("cis/SW_555_SER.cis");
876MODULE_FIRMWARE("cis/MT5634ZLX.cis");
877MODULE_FIRMWARE("cis/COMpad2.cis");
878MODULE_FIRMWARE("cis/COMpad4.cis");
879MODULE_FIRMWARE("cis/RS-COM-2P.cis");
880
881static struct pcmcia_driver serial_cs_driver = {
882 .owner = THIS_MODULE,
883 .drv = {
884 .name = "serial_cs",
885 },
886 .probe = serial_probe,
887 .remove = serial_detach,
888 .id_table = serial_ids,
889 .suspend = serial_suspend,
890 .resume = serial_resume,
891};
892
893static int __init init_serial_cs(void)
894{
895 return pcmcia_register_driver(&serial_cs_driver);
896}
897
898static void __exit exit_serial_cs(void)
899{
900 pcmcia_unregister_driver(&serial_cs_driver);
901}
902
903module_init(init_serial_cs);
904module_exit(exit_serial_cs);
905
906MODULE_LICENSE("GPL");