tjh.dev
Linux kernel mirror (for testing)
git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
kernel
os
linux
1/*
2 * Copyright (C) 1996-1998 Linus Torvalds & authors (see below)
3 */
4
5/*
6 * Authors:
7 * Jaromir Koutek <miri@punknet.cz>,
8 * Jan Harkes <jaharkes@cwi.nl>,
9 * Mark Lord <mlord@pobox.com>
10 * Some parts of code are from ali14xx.c and from rz1000.c.
11 *
12 * OPTi is trademark of OPTi, Octek is trademark of Octek.
13 *
14 * I used docs from OPTi databook, from ftp.opti.com, file 9123-0002.ps
15 * and disassembled/traced setupvic.exe (DOS program).
16 * It increases kernel code about 2 kB.
17 * I don't have this card no more, but I hope I can get some in case
18 * of needed development.
19 * My card is Octek PIDE 1.01 (on card) or OPTiViC (program).
20 * It has a place for a secondary connector in circuit, but nothing
21 * is there. Also BIOS says no address for
22 * secondary controller (see bellow in ide_init_opti621).
23 * I've only tested this on my system, which only has one disk.
24 * It's Western Digital WDAC2850, with PIO mode 3. The PCI bus
25 * is at 20 MHz (I have DX2/80, I tried PCI at 40, but I got random
26 * lockups). I tried the OCTEK double speed CD-ROM and
27 * it does not work! But I can't boot DOS also, so it's probably
28 * hardware fault. I have connected Conner 80MB, the Seagate 850MB (no
29 * problems) and Seagate 1GB (as slave, WD as master). My experiences
30 * with the third, 1GB drive: I got 3MB/s (hdparm), but sometimes
31 * it slows to about 100kB/s! I don't know why and I have
32 * not this drive now, so I can't try it again.
33 * I write this driver because I lost the paper ("manual") with
34 * settings of jumpers on the card and I have to boot Linux with
35 * Loadlin except LILO, cause I have to run the setupvic.exe program
36 * already or I get disk errors (my test: rpm -Vf
37 * /usr/X11R6/bin/XF86_SVGA - or any big file).
38 * Some numbers from hdparm -t /dev/hda:
39 * Timing buffer-cache reads: 32 MB in 3.02 seconds =10.60 MB/sec
40 * Timing buffered disk reads: 16 MB in 5.52 seconds = 2.90 MB/sec
41 * I have 4 Megs/s before, but I don't know why (maybe changes
42 * in hdparm test).
43 * After release of 0.1, I got some successful reports, so it might work.
44 *
45 * The main problem with OPTi is that some timings for master
46 * and slave must be the same. For example, if you have master
47 * PIO 3 and slave PIO 0, driver have to set some timings of
48 * master for PIO 0. Second problem is that opti621_set_pio_mode
49 * got only one drive to set, but have to set both drives.
50 * This is solved in compute_pios. If you don't set
51 * the second drive, compute_pios use ide_get_best_pio_mode
52 * for autoselect mode (you can change it to PIO 0, if you want).
53 * If you then set the second drive to another PIO, the old value
54 * (automatically selected) will be overrided by yours.
55 * There is a 25/33MHz switch in configuration
56 * register, but driver is written for use at any frequency.
57 *
58 * Version 0.1, Nov 8, 1996
59 * by Jaromir Koutek, for 2.1.8.
60 * Initial version of driver.
61 *
62 * Version 0.2
63 * Number 0.2 skipped.
64 *
65 * Version 0.3, Nov 29, 1997
66 * by Mark Lord (probably), for 2.1.68
67 * Updates for use with new IDE block driver.
68 *
69 * Version 0.4, Dec 14, 1997
70 * by Jan Harkes
71 * Fixed some errors and cleaned the code.
72 *
73 * Version 0.5, Jan 2, 1998
74 * by Jaromir Koutek
75 * Updates for use with (again) new IDE block driver.
76 * Update of documentation.
77 *
78 * Version 0.6, Jan 2, 1999
79 * by Jaromir Koutek
80 * Reversed to version 0.3 of the driver, because
81 * 0.5 doesn't work.
82 */
83
84#include <linux/types.h>
85#include <linux/module.h>
86#include <linux/kernel.h>
87#include <linux/pci.h>
88#include <linux/ide.h>
89
90#include <asm/io.h>
91
92#define DRV_NAME "opti621"
93
94#define READ_REG 0 /* index of Read cycle timing register */
95#define WRITE_REG 1 /* index of Write cycle timing register */
96#define CNTRL_REG 3 /* index of Control register */
97#define STRAP_REG 5 /* index of Strap register */
98#define MISC_REG 6 /* index of Miscellaneous register */
99
100static int reg_base;
101
102static DEFINE_SPINLOCK(opti621_lock);
103
104/* Write value to register reg, base of register
105 * is at reg_base (0x1f0 primary, 0x170 secondary,
106 * if not changed by PCI configuration).
107 * This is from setupvic.exe program.
108 */
109static void write_reg(u8 value, int reg)
110{
111 inw(reg_base + 1);
112 inw(reg_base + 1);
113 outb(3, reg_base + 2);
114 outb(value, reg_base + reg);
115 outb(0x83, reg_base + 2);
116}
117
118/* Read value from register reg, base of register
119 * is at reg_base (0x1f0 primary, 0x170 secondary,
120 * if not changed by PCI configuration).
121 * This is from setupvic.exe program.
122 */
123static u8 read_reg(int reg)
124{
125 u8 ret = 0;
126
127 inw(reg_base + 1);
128 inw(reg_base + 1);
129 outb(3, reg_base + 2);
130 ret = inb(reg_base + reg);
131 outb(0x83, reg_base + 2);
132
133 return ret;
134}
135
136static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
137{
138 ide_hwif_t *hwif = drive->hwif;
139 ide_drive_t *pair = ide_get_pair_dev(drive);
140 unsigned long flags;
141 unsigned long mode = XFER_PIO_0 + pio, pair_mode;
142 u8 tim, misc, addr_pio = pio, clk;
143
144 /* DRDY is default 2 (by OPTi Databook) */
145 static const u8 addr_timings[2][5] = {
146 { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */
147 { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */
148 };
149 static const u8 data_rec_timings[2][5] = {
150 { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */
151 { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */
152 };
153
154 ide_set_drivedata(drive, (void *)mode);
155
156 if (pair) {
157 pair_mode = (unsigned long)ide_get_drivedata(pair);
158 if (pair_mode && pair_mode < mode)
159 addr_pio = pair_mode - XFER_PIO_0;
160 }
161
162 spin_lock_irqsave(&opti621_lock, flags);
163
164 reg_base = hwif->io_ports.data_addr;
165
166 /* allow Register-B */
167 outb(0xc0, reg_base + CNTRL_REG);
168 /* hmm, setupvic.exe does this ;-) */
169 outb(0xff, reg_base + 5);
170 /* if reads 0xff, adapter not exist? */
171 (void)inb(reg_base + CNTRL_REG);
172 /* if reads 0xc0, no interface exist? */
173 read_reg(CNTRL_REG);
174
175 /* check CLK speed */
176 clk = read_reg(STRAP_REG) & 1;
177
178 printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
179
180 tim = data_rec_timings[clk][pio];
181 misc = addr_timings[clk][addr_pio];
182
183 /* select Index-0/1 for Register-A/B */
184 write_reg(drive->dn & 1, MISC_REG);
185 /* set read cycle timings */
186 write_reg(tim, READ_REG);
187 /* set write cycle timings */
188 write_reg(tim, WRITE_REG);
189
190 /* use Register-A for drive 0 */
191 /* use Register-B for drive 1 */
192 write_reg(0x85, CNTRL_REG);
193
194 /* set address setup, DRDY timings, */
195 /* and read prefetch for both drives */
196 write_reg(misc, MISC_REG);
197
198 spin_unlock_irqrestore(&opti621_lock, flags);
199}
200
201static const struct ide_port_ops opti621_port_ops = {
202 .set_pio_mode = opti621_set_pio_mode,
203};
204
205static const struct ide_port_info opti621_chipset __devinitdata = {
206 .name = DRV_NAME,
207 .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
208 .port_ops = &opti621_port_ops,
209 .host_flags = IDE_HFLAG_NO_DMA,
210 .pio_mask = ATA_PIO4,
211};
212
213static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
214{
215 return ide_pci_init_one(dev, &opti621_chipset, NULL);
216}
217
218static const struct pci_device_id opti621_pci_tbl[] = {
219 { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
220 { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
221 { 0, },
222};
223MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
224
225static struct pci_driver opti621_pci_driver = {
226 .name = "Opti621_IDE",
227 .id_table = opti621_pci_tbl,
228 .probe = opti621_init_one,
229 .remove = ide_pci_remove,
230 .suspend = ide_pci_suspend,
231 .resume = ide_pci_resume,
232};
233
234static int __init opti621_ide_init(void)
235{
236 return ide_pci_register_driver(&opti621_pci_driver);
237}
238
239static void __exit opti621_ide_exit(void)
240{
241 pci_unregister_driver(&opti621_pci_driver);
242}
243
244module_init(opti621_ide_init);
245module_exit(opti621_ide_exit);
246
247MODULE_AUTHOR("Jaromir Koutek, Jan Harkes, Mark Lord");
248MODULE_DESCRIPTION("PCI driver module for Opti621 IDE");
249MODULE_LICENSE("GPL");