kernel / arch / powerpc / sysdev / cpm2_common.c

/*
 * General Purpose functions for the global management of the
 * 8260 Communication Processor Module.
 * Copyright (c) 1999-2001 Dan Malek <[e-mail]>
 * Copyright (c) 2000 MontaVista Software, Inc ([e-mail])
 *	2.3.99 Updates
 *
 * 2006 (c) MontaVista Software, Inc.
 * Vitaly Bordug <[e-mail]>
 * 	Merged to arch/powerpc from arch/ppc/syslib/cpm2_common.c
 *
 * This file is licensed under the terms of the GNU General Public License
 * version 2. This program is licensed "as is" without any warranty of any
 * kind, whether express or implied.
 */

/*
 *
 * In addition to the individual control of the communication
 * channels, there are a few functions that globally affect the
 * communication processor.
 *
 * Buffer descriptors must be allocated from the dual ported memory
 * space.  The allocator for that is here.  When the communication
 * process is reset, we reclaim the memory available.  There is
 * currently no deallocator for this memory.
 */
#include <linux/errno.h>
#include <linux/sched.h>
#include <linux/kernel.h>
#include <linux/param.h>
#include <linux/string.h>
#include <linux/mm.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/of.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mpc8260.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/cpm2.h>
#include <asm/rheap.h>
#include <asm/fs_pd.h>

#include <sysdev/fsl_soc.h>

#ifndef CONFIG_PPC_CPM_NEW_BINDING
static void cpm2_dpinit(void);
#endif

cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor space */

/* We allocate this here because it is used almost exclusively for
 * the communication processor devices.
 */
cpm2_map_t __iomem *cpm2_immr;

#define CPM_MAP_SIZE	(0x40000)	/* 256k - the PQ3 reserve this amount
					   of space for CPM as it is larger
					   than on PQ2 */

void __init cpm2_reset(void)
{
#ifdef CONFIG_PPC_85xx
	cpm2_immr = ioremap(CPM_MAP_ADDR, CPM_MAP_SIZE);
#else
	cpm2_immr = ioremap(get_immrbase(), CPM_MAP_SIZE);
#endif

	/* Reclaim the DP memory for our use.
	 */
#ifdef CONFIG_PPC_CPM_NEW_BINDING
	cpm_muram_init();
#else
	cpm2_dpinit();
#endif

	/* Tell everyone where the comm processor resides.
	 */
	cpmp = &cpm2_immr->im_cpm;
}

/* Set a baud rate generator.  This needs lots of work.  There are
 * eight BRGs, which can be connected to the CPM channels or output
 * as clocks.  The BRGs are in two different block of internal
 * memory mapped space.
 * The baud rate clock is the system clock divided by something.
 * It was set up long ago during the initial boot phase and is
 * is given to us.
 * Baud rate clocks are zero-based in the driver code (as that maps
 * to port numbers).  Documentation uses 1-based numbering.
 */
#define BRG_INT_CLK	(get_brgfreq())
#define BRG_UART_CLK	(BRG_INT_CLK/16)

/* This function is used by UARTS, or anything else that uses a 16x
 * oversampled clock.
 */
void
cpm_setbrg(uint brg, uint rate)
{
	u32 __iomem *bp;

	/* This is good enough to get SMCs running.....
	*/
	if (brg < 4) {
		bp = cpm2_map_size(im_brgc1, 16);
	} else {
		bp = cpm2_map_size(im_brgc5, 16);
		brg -= 4;
	}
	bp += brg;
	out_be32(bp, (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN);

	cpm2_unmap(bp);
}

/* This function is used to set high speed synchronous baud rate
 * clocks.
 */
void
cpm2_fastbrg(uint brg, uint rate, int div16)
{
	u32 __iomem *bp;
	u32 val;

	if (brg < 4) {
		bp = cpm2_map_size(im_brgc1, 16);
	}
	else {
		bp = cpm2_map_size(im_brgc5, 16);
		brg -= 4;
	}
	bp += brg;
	val = ((BRG_INT_CLK / rate) << 1) | CPM_BRG_EN;
	if (div16)
		val |= CPM_BRG_DIV16;

	out_be32(bp, val);
	cpm2_unmap(bp);
}

int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode)
{
	int ret = 0;
	int shift;
	int i, bits = 0;
	cpmux_t __iomem *im_cpmux;
	u32 __iomem *reg;
	u32 mask = 7;

	u8 clk_map[][3] = {
		{CPM_CLK_FCC1, CPM_BRG5, 0},
		{CPM_CLK_FCC1, CPM_BRG6, 1},
		{CPM_CLK_FCC1, CPM_BRG7, 2},
		{CPM_CLK_FCC1, CPM_BRG8, 3},
		{CPM_CLK_FCC1, CPM_CLK9, 4},
		{CPM_CLK_FCC1, CPM_CLK10, 5},
		{CPM_CLK_FCC1, CPM_CLK11, 6},
		{CPM_CLK_FCC1, CPM_CLK12, 7},
		{CPM_CLK_FCC2, CPM_BRG5, 0},
		{CPM_CLK_FCC2, CPM_BRG6, 1},
		{CPM_CLK_FCC2, CPM_BRG7, 2},
		{CPM_CLK_FCC2, CPM_BRG8, 3},
		{CPM_CLK_FCC2, CPM_CLK13, 4},
		{CPM_CLK_FCC2, CPM_CLK14, 5},
		{CPM_CLK_FCC2, CPM_CLK15, 6},
		{CPM_CLK_FCC2, CPM_CLK16, 7},
		{CPM_CLK_FCC3, CPM_BRG5, 0},
		{CPM_CLK_FCC3, CPM_BRG6, 1},
		{CPM_CLK_FCC3, CPM_BRG7, 2},
		{CPM_CLK_FCC3, CPM_BRG8, 3},
		{CPM_CLK_FCC3, CPM_CLK13, 4},
		{CPM_CLK_FCC3, CPM_CLK14, 5},
		{CPM_CLK_FCC3, CPM_CLK15, 6},
		{CPM_CLK_FCC3, CPM_CLK16, 7},
		{CPM_CLK_SCC1, CPM_BRG1, 0},
		{CPM_CLK_SCC1, CPM_BRG2, 1},
		{CPM_CLK_SCC1, CPM_BRG3, 2},
		{CPM_CLK_SCC1, CPM_BRG4, 3},
		{CPM_CLK_SCC1, CPM_CLK11, 4},
		{CPM_CLK_SCC1, CPM_CLK12, 5},
		{CPM_CLK_SCC1, CPM_CLK3, 6},
		{CPM_CLK_SCC1, CPM_CLK4, 7},
		{CPM_CLK_SCC2, CPM_BRG1, 0},
		{CPM_CLK_SCC2, CPM_BRG2, 1},
		{CPM_CLK_SCC2, CPM_BRG3, 2},
		{CPM_CLK_SCC2, CPM_BRG4, 3},
		{CPM_CLK_SCC2, CPM_CLK11, 4},
		{CPM_CLK_SCC2, CPM_CLK12, 5},
		{CPM_CLK_SCC2, CPM_CLK3, 6},
		{CPM_CLK_SCC2, CPM_CLK4, 7},
		{CPM_CLK_SCC3, CPM_BRG1, 0},
		{CPM_CLK_SCC3, CPM_BRG2, 1},
		{CPM_CLK_SCC3, CPM_BRG3, 2},
		{CPM_CLK_SCC3, CPM_BRG4, 3},
		{CPM_CLK_SCC3, CPM_CLK5, 4},
		{CPM_CLK_SCC3, CPM_CLK6, 5},
		{CPM_CLK_SCC3, CPM_CLK7, 6},
		{CPM_CLK_SCC3, CPM_CLK8, 7},
		{CPM_CLK_SCC4, CPM_BRG1, 0},
		{CPM_CLK_SCC4, CPM_BRG2, 1},
		{CPM_CLK_SCC4, CPM_BRG3, 2},
		{CPM_CLK_SCC4, CPM_BRG4, 3},
		{CPM_CLK_SCC4, CPM_CLK5, 4},
		{CPM_CLK_SCC4, CPM_CLK6, 5},
		{CPM_CLK_SCC4, CPM_CLK7, 6},
		{CPM_CLK_SCC4, CPM_CLK8, 7},
	};

	im_cpmux = cpm2_map(im_cpmux);

	switch (target) {
	case CPM_CLK_SCC1:
		reg = &im_cpmux->cmx_scr;
		shift = 24;
	case CPM_CLK_SCC2:
		reg = &im_cpmux->cmx_scr;
		shift = 16;
		break;
	case CPM_CLK_SCC3:
		reg = &im_cpmux->cmx_scr;
		shift = 8;
		break;
	case CPM_CLK_SCC4:
		reg = &im_cpmux->cmx_scr;
		shift = 0;
		break;
	case CPM_CLK_FCC1:
		reg = &im_cpmux->cmx_fcr;
		shift = 24;
		break;
	case CPM_CLK_FCC2:
		reg = &im_cpmux->cmx_fcr;
		shift = 16;
		break;
	case CPM_CLK_FCC3:
		reg = &im_cpmux->cmx_fcr;
		shift = 8;
		break;
	default:
		printk(KERN_ERR "cpm2_clock_setup: invalid clock target\n");
		return -EINVAL;
	}

	if (mode == CPM_CLK_RX)
		shift += 3;

	for (i = 0; i < ARRAY_SIZE(clk_map); i++) {
		if (clk_map[i][0] == target && clk_map[i][1] == clock) {
			bits = clk_map[i][2];
			break;
		}
	}
	if (i == ARRAY_SIZE(clk_map))
	    ret = -EINVAL;

	bits <<= shift;
	mask <<= shift;

	out_be32(reg, (in_be32(reg) & ~mask) | bits);

	cpm2_unmap(im_cpmux);
	return ret;
}

int cpm2_smc_clk_setup(enum cpm_clk_target target, int clock)
{
	int ret = 0;
	int shift;
	int i, bits = 0;
	cpmux_t __iomem *im_cpmux;
	u8 __iomem *reg;
	u8 mask = 3;

	u8 clk_map[][3] = {
		{CPM_CLK_SMC1, CPM_BRG1, 0},
		{CPM_CLK_SMC1, CPM_BRG7, 1},
		{CPM_CLK_SMC1, CPM_CLK7, 2},
		{CPM_CLK_SMC1, CPM_CLK9, 3},
		{CPM_CLK_SMC2, CPM_BRG2, 0},
		{CPM_CLK_SMC2, CPM_BRG8, 1},
		{CPM_CLK_SMC2, CPM_CLK4, 2},
		{CPM_CLK_SMC2, CPM_CLK15, 3},
	};

	im_cpmux = cpm2_map(im_cpmux);

	switch (target) {
	case CPM_CLK_SMC1:
		reg = &im_cpmux->cmx_smr;
		mask = 3;
		shift = 4;
		break;
	case CPM_CLK_SMC2:
		reg = &im_cpmux->cmx_smr;
		mask = 3;
		shift = 0;
		break;
	default:
		printk(KERN_ERR "cpm2_smc_clock_setup: invalid clock target\n");
		return -EINVAL;
	}

	for (i = 0; i < ARRAY_SIZE(clk_map); i++) {
		if (clk_map[i][0] == target && clk_map[i][1] == clock) {
			bits = clk_map[i][2];
			break;
		}
	}
	if (i == ARRAY_SIZE(clk_map))
	    ret = -EINVAL;

	bits <<= shift;
	mask <<= shift;

	out_8(reg, (in_8(reg) & ~mask) | bits);

	cpm2_unmap(im_cpmux);
	return ret;
}

#ifndef CONFIG_PPC_CPM_NEW_BINDING
/*
 * dpalloc / dpfree bits.
 */
static spinlock_t cpm_dpmem_lock;
/* 16 blocks should be enough to satisfy all requests
 * until the memory subsystem goes up... */
static rh_block_t cpm_boot_dpmem_rh_block[16];
static rh_info_t cpm_dpmem_info;
static u8 __iomem *im_dprambase;

static void cpm2_dpinit(void)
{
	spin_lock_init(&cpm_dpmem_lock);

	/* initialize the info header */
	rh_init(&cpm_dpmem_info, 1,
			sizeof(cpm_boot_dpmem_rh_block) /
			sizeof(cpm_boot_dpmem_rh_block[0]),
			cpm_boot_dpmem_rh_block);

	im_dprambase = cpm2_immr;

	/* Attach the usable dpmem area */
	/* XXX: This is actually crap. CPM_DATAONLY_BASE and
	 * CPM_DATAONLY_SIZE is only a subset of the available dpram. It
	 * varies with the processor and the microcode patches activated.
	 * But the following should be at least safe.
	 */
	rh_attach_region(&cpm_dpmem_info, CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
}

/* This function returns an index into the DPRAM area.
 */
unsigned long cpm_dpalloc(uint size, uint align)
{
	unsigned long start;
	unsigned long flags;

	spin_lock_irqsave(&cpm_dpmem_lock, flags);
	cpm_dpmem_info.alignment = align;
	start = rh_alloc(&cpm_dpmem_info, size, "commproc");
	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);

	return (uint)start;
}
EXPORT_SYMBOL(cpm_dpalloc);

int cpm_dpfree(unsigned long offset)
{
	int ret;
	unsigned long flags;

	spin_lock_irqsave(&cpm_dpmem_lock, flags);
	ret = rh_free(&cpm_dpmem_info, offset);
	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);

	return ret;
}
EXPORT_SYMBOL(cpm_dpfree);

/* not sure if this is ever needed */
unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align)
{
	unsigned long start;
	unsigned long flags;

	spin_lock_irqsave(&cpm_dpmem_lock, flags);
	cpm_dpmem_info.alignment = align;
	start = rh_alloc_fixed(&cpm_dpmem_info, offset, size, "commproc");
	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);

	return start;
}
EXPORT_SYMBOL(cpm_dpalloc_fixed);

void cpm_dpdump(void)
{
	rh_dump(&cpm_dpmem_info);
}
EXPORT_SYMBOL(cpm_dpdump);

void *cpm_dpram_addr(unsigned long offset)
{
	return (void *)(im_dprambase + offset);
}
EXPORT_SYMBOL(cpm_dpram_addr);
#endif /* !CONFIG_PPC_CPM_NEW_BINDING */

struct cpm2_ioports {
	u32 dir, par, sor, odr, dat;
	u32 res[3];
};

void cpm2_set_pin(int port, int pin, int flags)
{
	struct cpm2_ioports __iomem *iop =
		(struct cpm2_ioports __iomem *)&cpm2_immr->im_ioport;

	pin = 1 << (31 - pin);

	if (flags & CPM_PIN_OUTPUT)
		setbits32(&iop[port].dir, pin);
	else
		clrbits32(&iop[port].dir, pin);

	if (!(flags & CPM_PIN_GPIO))
		setbits32(&iop[port].par, pin);
	else
		clrbits32(&iop[port].par, pin);

	if (flags & CPM_PIN_SECONDARY)
		setbits32(&iop[port].sor, pin);
	else
		clrbits32(&iop[port].sor, pin);

	if (flags & CPM_PIN_OPENDRAIN)
		setbits32(&iop[port].odr, pin);
	else
		clrbits32(&iop[port].odr, pin);
}